It’s so easy with tp24 Plug & Play G40 LED Downlights
AWARDW
INNING DESIGN
50m
m
G40 Downlight lamp specification:
G40 Downlight information:
2 year LED warranty (upon registration)300 Lumens3.5W3000K15,000 hours lamp life
•••••
Plug & play, just wire the first connector
No fire hood required, roll insulation straight over the top
Compliant with building regsand sustainable code
Minimal electrical skill required to fit
IP65 for bathrooms, 30, 60 & 90 minute fire rated, air sealing and sound proof
Available in white, chrome and satin silver
Plug & Play G40Downlight Guide
2
Installation...
1
3
4
2
Unbox your LED lamp. To activate your free two year warranty, register the unique serial number printed on the base of each lamp at www.tp24.com within 14 days of purchase.
To insert your LED lamp, twist off the bezel on the downlight, insert your push fit LED lamp and reattach the bezel.
Cut the holes for your downlights and feed the plug & play tp24 ‘Linkage cables’ (5712) through each hole.
For advice on downlight spacing visit:www.tp24.com/downlight-advice
Isolate the power supply and wire the tp24 ‘Terminal connection cable’ (5710) to the lighting circuit. If you are not sure how to safely wire a light fitting, hire an electrician.
Once you’ve connected the first downlight to the tp24 ‘Terminal connection cable’ (5710), connect the downlights to the ‘in’ and ‘out’ linkage cables.
Fit the unit into the ceiling hole by bending back the springs and pushing the unit into the pre-cut hole until the springs snap back into place.
33
2
1 Choose your colour & note down the code(s) (shown above)
Place your order
Decide which components you need, you will need one ‘Terminal connection cable’ (5710) for the first fitting in the series and one ‘Linkage cable’ (5712) for each subsequent fitting, depending on the spacing. If the spacing is greater than the 1.7m cable, join the two cables together and tape up if buried. Add an ‘End cap’ (5715) to the spare socket on the last downlight if required. G40 lamps are included with your downlights.
5710 - Terminalconnection cableL100
8620 - SMD G40 LED lamp3.5W 300 Lumens(included with downlight)
5700/5702/5704G40 downlightwith male & female plug & play sockets (downlight includes 8620 SMD G40 LED lamp)
5712 - Linkage cableL1700
5715 - End capUse this to cap off your last spare connection point
5700White
Finishes & codes: Additional components:
Ordering process:
5704Satin silver
Rear view
5702Chrome
4
Slimline...
The tp24 plug & play downlight measures an ultra slimline 50mm in depth.
Joist Insulation Ceiling
G40 Plug & playdownlight
Regulardownlight
Hole cut size: 75mm
G40 tp24 downlight Regular tp24 downlight
50mm
93mm
The slimness of the G40 plug & play downlight offers a number of benefits:
• It’s suitable for use between floors, in loft conversions, flat roofs and sloping roof sides where space is limited
• Insulation can be laid over and around the unit without leaving any air voids thus ensuring there is no thermal bridging
• The unit is fully fire rated, there is no need for a separate fire hood• tp24 G40 downlights are fully compliant with all current building regulations
and sustainable codes• Ideal for caravans, motorhomes, boats and all standard roof spaces
5
Many slimline LED fittings on the market feature fixed, built-in LED lamps, this means that when the lamp fails you need to replace the entire fitting, which is not sustainable. The tp24 G40 plug & play downlights come complete with our slimline, award winning G40 LED lamps which are fully removable, replaceable and upgradeable in the future.
Each tp24 LED lamp has a unique serial number printed on the base, when this unique number is registered on our website (within 14 days of purchase) it activates your two year warranty and enables tp24 to track each batch and ensure that any potential problems are tracked and resolved.
IP65 for Bathrooms...
Not ‘Built-in’ LED...
AWARD
WINNING DESIG
N
Plug & Play...
The design of the tp24 G40 plug & play downlights saves so much time and hassle over conventional wired downlights, eliminating the need to wire each downlight makes them simpler and faster to fit. See installation instructions on page 2.
The tp24 plug & play G40 downlight features a seal on the inside of the bezel designed to lock out moisture. This fitting has an ingress protection rating of IP65 making it suitable for use in certain areas of the bathroom. Please refer to the latest IEE wiring regulations.
Slimfit <50mm
Plug & play installation
Push fit award winningG40 LED lamp
Free 2 year LED warranty (upon registration)
Fire rated & air sealing
IP65 rating
Finishes available inChrome/Satin silver/White
Compliant with building regs & sustainable code
G40 Plug & Play DownlightDon’t Settle For Less
The G40 Plug & play
downlight is not just any
downlight.
Generic Downlight
Plug & Play G40...Not just any downlight
G40 Plug & PlayDownlights by tp24
AWARD
WINNING DESIG
N