46
GeneRal InfoRMaTIon
TecH ManUal – M
ecHanIcal ancHoRs ©2013 D
eWalT PRInTeD 6/13
meC
Han
iCal a
nCHo
rS
www.DeWalT.com/anchors
secTIon conTenTsGeneral Information
Installation Information
Design Information
Material Information
ordering Information
assembly
VeRsIonsstraight collar:
carbon steel, Zinc Plated
stainless steel
Hot Dipped Galvanized (no eTa approval)
lipped collar
carbon steel, Zinc Plated
appRoVals• eTa-13/0056
geneRal InfoRmaTIon
Dm-Pro Part 6Drop-In Anchor
ProDUCt DeSCriPtion
The DM-PRo is a drop-in anchor which shows good performance for competitive price for typical mass applications. It can be used in a wide range of concrete strengths and in all installation directions. The DM-PRo is available in carbon steel and stainless steel. The lipped version is furnished with a flange preventing the anchor to pertain too deep into the concrete. With an eTaG 001 Part 6 approval, the DM-PRo can also be used in cracked concrete, but only for multiple connection in non-structural applications.
General aPPliCationS anD USeS
featUreS anD BenefitS
•Price competitive anchoring for all kinds of mechanical, electrical and plumbing installation
•straightforward installation with hand driven hammer
•suitable for threaded steel elements of various strength and grade
•Internally threaded anchor for easy bolt removability and service work
aPProValS anD liStinGS
ETAG 001 Part 6 F120
loaDinG ConDitionS
STATIC QUASI-STATIC
SUitaBle BaSe materialS
DEWALT DESIGN ASSISTReal-Time anchor Design software
www.DeWalTdesignassist.com
www.DEWALT.com/anchors 47
TecH
Man
Ual
– M
ecHa
nIca
l an
cHoR
s ©
2013
DeW
alT
PRI
nTeD
6/1
3
InsTallaTIon InfoRMaTIon
meC
Han
iCal
an
CHo
rSInsTallaTIon InfoRmaTIon
inStallation Data
notation UnitDm-pRo part 6
m6 m8 m10 m12
anchor diameter d [mm] 8 10 12 16
nominal drill bit diameter d0 [mm] 8 10 12 16
Diameter of hole clearance in fixture df [mm] 7 9 12 14
effective embedment depth hef [mm] 25 30 40 50
Drill hole depth h1 [mm] 26 32 42 43
Minimum member thickness for hmin hmin [mm] 80 80 80 100
Minimum spacing smin [mm] 150 150 150 150
Minimum edge distance cmin [mm] 200 200 200 200
Maximum torque threaded rod Tmax [nm] 4 8 15 35
hmin
hef
d0
df
Sw
Tmax
h1
tfix
inStallation inStrUCtionS
1.) Using the proper drill bit size, drill a hole into the base material to the required depth.
2.) Remove dust and debris from the hole using a hand pump or compressed air.
3.) Insert drop in anchor in to drilled hole.
4.) Expand anchor by hammering on setting tool until the collar of the setting tool touches the fixture.
5.) Insert threaded rod and prestress with defined torque.
for complete installation instructions, see technical approval.
48
TecH ManUal – M
ecHanIcal ancHoRs ©2013 D
eWalT PRInTeD 6/13
DesIGn InfoRMaTIon
www.DEWALT.com/anchors
meC
Han
iCal a
nCHo
rS
DesIgn InfoRmaTIon
loaD CaPaCitieS - ParameterS for CalCUlation of DeSiGn StrenGtHAccording to ETAG 001 Annex C Method A.
notation UnitDm-pRo
m6 m8 m10 m12
capacity for all directions and failure modes
Uncracked and cracked concrete
characteristic resistance c20/25 to c50/60 f0Rk [kn] 2.0 2.0 4.0 5.0
Partial safety factor gMp
1) [-] 2.42) 2.32) 2.12)
Design resistance c20/25 to c50/60 fRd [kn] 0.83 0.87 1.90 2.38
characteristic spacing scr [mm] 200 200 200 200
characteristic edge distance ccr [mm] 150 150 150 150
steel failure with lever arm
Steel failure with lever arm (bending)
characteristic resistance, 8.8 steel M0Rk,s [nm] 12.2 27.3 43.0 104.8
Partial safety factor gMs
1) [-] 1.25
characteristic resistance, a4-70 M0Rk,s [nm] 10.7 26.2 52.3 91.7
Partial safety factor gMp
1) [-] 1.56
1) In absence of other national regulations
2) Partial safety factor of g2 = 1.4 is included
maTeRIal InfoRmaTIon
material SPeCifiCation
31
2
part no. Designation Version material protection
1 anchor sleevesDM-PRo/ DM-lip-Pro cold formed steel, grade sWRcH8a Zinc plated 5 µm
DM-ss-Pro Machined steel, grade ss3161) -
2 expansion conesDM-PRo/ DM-lip-Pro cold formed steel, grade sWRcH8a Zinc plated 5 µm
DM-ss-Pro Machined steel, grade ss3161) -
3 screw or threaded rod
DM-PRo/ DM-lip-Pro steel strength class 4.6, 5.6, 5.8 or 8.8 according to Iso 898-1 Zinc plated 5 µm
DM-ss-Pro steel strength class a4-701) -
1) Mat. no.: 1.4401, 1.4404, 1.4439, 1.4571
www.DEWALT.com/anchors 49
TecH
Man
Ual
– M
ecHa
nIca
l an
cHoR
s ©
2013
DeW
alT
PRI
nTeD
6/1
3
oRDeRInG InfoRMaTIon
meC
Han
iCal
an
CHo
rSoRDeRIng InfoRmaTIon
Anchor
art. no. Type Dia.
[mm]length [mm]
box qty.
carton qty.
DM-PRO
DM-PRO - zinc plated
DfM2110500 M6 Drop-in anchor - zinc plated M6 25 100 1600
DfM2110550 M8 Drop-in anchor - zinc plated M8 30 100 800
DfM2110600 M10 Drop-in anchor - zinc plated M10 40 100 800
DfM2110650 M12 Drop-in anchor - zinc plated M12 50 100 400
DfM2110700 M16 Drop-in anchor - zinc plated M16 65 25 100
DfM2110750 M20 Drop-in anchor - zinc plated M20 80 25 100
DM-LIP-PRO - zinc plated
DM-LiP-PRO
DfM2110000 M6 lipped drop-in anchor - zinc plated M6 25 100 1600
DfM2110100 M8 lipped drop-in anchor - zinc plated M8 30 100 800
DfM2110150 M10 lipped drop-in anchor - zinc plated M10 40 100 800
DfM2110200 M12 lipped drop-in anchor - zinc plated M12 50 100 400
DfM2110300 M16 lipped drop-in anchor - zinc plated M16 65 25 100
DfM2110250 M20 lipped drop-in anchor - zinc plated M20 80 25 100
DM-SS-PRO - A4 stainless steel
DM-SS-PRO
DfM2120000 M6 Drop-in anchor - a4 ss M6 25 100 1600
DfM2120050 M8 Drop-in anchor - a4 ss M8 30 100 800
DfM2120100 M10 Drop-in anchor - a4 ss M10 40 100 800
DfM2120150 M12 Drop-in anchor - a4 ss M12 50 100 400
DfM2120200 M16 Drop-in anchor - a4 ss M16 65 25 100
DfM2120250 M20 Drop-in anchor - a4 ss M20 80 25 100
DMG-PRO - Hot dipped galvanized
DMg-PRO
DfM2150000 M6 Drop-in anchor - HDG M6 25 100 1600
DfM2150050 M8 Drop-in anchor - HDG M8 30 100 800
DfM2150100 M10 Drop-in anchor - HDG M10 40 100 800
DfM2150150 M12 Drop-in anchor - HDG M12 50 100 400
DfM2150200 M16 Drop-in anchor - HDG M16 65 25 100
DfM2150250 M20 Drop-in anchor - HDG M20 80 25 100
Setting Tool for drop-in anchors
art. no. Type box
qty. carton
qty.
SeTTing TOOL
DfM2100010 M6 Drop-in setting tool 1 20
DfM2100060 M8 Drop-in setting tool 1 20
DfM2100110 M10 Drop-in setting tool 1 20
DfM2100160 M12 Drop-in setting tool 1 20
DfM2100210 M16 Drop-in setting tool 1 20
DfM2100260 M20 Drop-in setting tool 1 20