HABILITATION THESIS
RESEARCHES ON POSSIBILITIES TO IMPROVE
ENGINES FUELLING
Assoc. Prof. Ph.D. Florin Emil MARIA IU Technical University of Cluj-Napoca
Faculty of Mechanics
Automotive Engineering and Transports Department
2015
Habilitation thesis – F. Mariasiu 1
!
!
SUMMARY
PAGE
Acknowledgments!!!!!!!!!!!!!!!!!!!!!!!!!!!! 2
Abstract!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.. 3
Nomenclature!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 5
1. CONTEXT OF HABILITATION!!!!!!!!!!!!!!!!!!!!!. 9
2. RESEARCH DIRECTIONS AND COMPETENCES!!!!!!!!!!!!.. 11
3. RESEARCH ACTIVITIES AND RESULTS!!!!!!!!!!!!!!!!. 14
4. CONTEXT OF RESEARCH WORK!!!!!!!!!!!!!!!!!!!. 18
4.1. NECCESITY AND CONTEMPORARY CONTEXT OF RESEARCH ACTIVITIES!!!!!!!!!!!!!!!!!!!!!!!!!!!..
18
4.2. POSSIBILITIES TO INCRESE BIOFUEL’S POTENTIAL USED IN
INTERNAL COMBUSTION ENGINES FUELLING!!!!!!!!!!!
20
4.2.1. Effects of biofuel characteristics on injection process!!!!... 20
4.2.2. Effects of external energy (ultrasonic) application on biofuel use performances!!!!!!!!!!!!!!!!!!!!!!..
39
4.2.3. Possibilities to improve cold-start process of engines fuelled with biofuels!!!!!!!!!!!!!!!!!!!!!!!!!
55
4.2.4. Possibilities to reduce engine’s friction losses at cold-start!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
61
5. CONCLUSIONS!!!!!!!!!!!!!!!!!!!!!!!!!!!.. 75
6. CAREER DEVELOPMENT PLAN. !!!!!!!!!!!!!!!!!!! 77
References!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!. 79
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 2
!
!
Acknowledgments
Reaching a new level of development and professional training by supporting
habilitation thesis would not have been possible without the continued support of
those around me.
Without the unconditionally help of my family, confidence of department
leadership and collegiate collaboration with members of Automotive Engineering and
Transports Department, this would not be possible.
Therefore, now, all my thanks and good thoughts are turning to them.
Assoc. Prof. Florin Emil MARIASIU, PhD
Habilitation thesis – F. Mariasiu 3
!
!
Abstract
The habilitation thesis in mechanical engineering domain of candidate (assoc.prof.
Florin Emil MARIASIU, PhD) represents the synthesis of educational and research activities
conducted at the Technical University of Cluj-Napoca, Department of Automotive and
Transportation.
Research directions addressed by the candidate are refers to investigate the
possibility of increasing the efficient use of biofuels in internal combustion engines fuelling.
As a result of research conducted, were identified contemporary issues which this topic
facing and using original and unconventional methods, were able to manage the issuance of
applicative and relevant solutions and conclusions presented through scientific articles and
books published.
The context in which candidate’s need to follow habilitation process is analyzed and
justified is found in the thesis’ first chapter (CONTEXT OF HABILITATION).
In the second chapter of habilitation thesis "RESEARCH DIRECTIONS AND
COMPETENCES", are presented the research directions followed by the candidate and skills
held by it, as a direct results of professional and academic development.
Chapter 3 entitled "RESEARCH ACTIVITIES AND RESULTS" reviews the scientific
results obtained through research activities. Are presented scientific articles, published books
in the field of biofuels and internal combustion engines, the experience in managing and
conducting research projects, awards and distinctions, patent applications, national and
international collaborations with academia.
The widely development and detailing of research activity in biofuels is being
conducted under Chapter 4 "CONTEXT OF RESEARCH WORK". Based on the summary of
the main articles published in important scientific journals, are presented research directions
and results. Were discussed issues related to the investigation of possibilities: to increase
the efficiency of biofuels use in internal combustion engines fuelling, to optimize engine cold
start process and to reduce engine friction losses. Solutions presented have an original and
unconventional approach on investigated topics (subjects), and also a applicative character
by issuing two patent applications based on the results of this research.
Opinion issued on this basis is found in a succinct (summary) form in the fifth chapter
of the habilitation thesis "CONCLUSIONS". It presents new research directions opened by
the results already obtained.
In the last chapter (Chapter 6 "CAREER DEVELOPMENT PLAN") are highlighted
current and future directions (on short- and long-term) in academic and research career and
directions to be followed by the candidate.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 4
!
!
Rezumat
Teza de abilitare în domeniul ingineriei mecanice a candidatului, conf.dr.ing. Florin
Emil MARIA!IU, reprezint" sinteza activit"#ii educa#ionale $i de cercetare desf"$urate în
cadrul Universit"#ii Tehnice din Cluj-Napoca, departamentul Autovehicule Rutiere $i
Transporturi.
Direc#iile de cercetare abordate de c"tre candidat se refer" la investigarea posibilit"#ilor de
cre$tere a eficien#ei utiliz"ri biocombustibililor în alimentarea motoarelor cu ardere intern".
În urma activit"#ii de cercetare desfa$urate, s-au identificat problemele contemporane
cu care se confrunt" subiectul tratat, iar prin utilizarea unor metode originale $i
neconven#ionale s-a reu$it emiterea de concluzii $i solutii aplicative pertinente, prezentate
prin intermediul articolelor $tiin#ifice $i a c"rtilor de specialitate publicate.
Contextul în care necesitatea abilit"rii în $tiin#" a candidatului este analizat" $i
justificat", se regase$te în primul capitol al tezei (CONTEXT OF HABILITATION).
În al doilea capitol al tezei de abilitare “RESEARCH DIRECTIONS AND
COMPETENCES”, se prezint" direc#iile de cercetare urmate de candidat $i competen#ele
de#inute de c"tre acesta ca urmare a dezvolt"rii profesionale $i academice.
Capitolul 3 intitulat “RESEARCH ACTIVITIES AND RESULTS”, trece în revist"
rezultatele $tiin#ifice ob#inute prin desf"$urarea activit"#ilor de cercetare. Sunt prezentate
articolele $tiin#ifice publicate, c"r#ile din domeniu, experien#a în managementul $i derularea
proiectelor de cercetare, premiile $i distinc#iile ob#inute, cererile de brevet de inven#ie,
colabor"rile na#ionale $i interna#ionale cu mediul academic.
Dezvoltarea pe larg a activitâ#ii de cercetare în domeniul biocombustibililor este
realizat" în cadrul capitolului 4 “CONTEXT OF RESEARCH WORK”. Pe baza sintezei
principalelor articole publicate în reviste (jurnale) $tiin#ifice importante, sunt prezentate
direc#iile $i rezultatele cercet"riilor efectuate. Au fost abordate subiecte ce #in de investigarea
posibilit"#ilor: de cre$tere a eficien#ei utiliz"rii biocombustibililor în motoarele cu ardere
intern", de optimizare a procesului de pornire la rece a motoarelor $i reducerea pierderilor
prin frecare. Solu#iile oferite prezint" caracterul original $i neconven#ional al abord"rii temelor
(subiectelor) investigate, dar $i caracterul aplicativ prin emiterea a dou" cereri de inven#ie
bazate pe rezultatele acestor cercet"ri.
Concluziile emise pe baza celor prezentate anterior, se reg"sesc într-o form"
succint" în cadrul capitolului al cincilea al tezei de abilitare “CONCLUSIONS”. Se prezint" $i
noile direc#ii de cercetare deschise de rezultatele deja ob#inute.
În cadrul ultimului capitol al tezei ( capitolul 6 “CAREER DEVELOPMENT PLAN”)
sunt reliefate direc#iile prezente $i viitoare (pe termen scurt $i lung) ale carierei universitare $i
ale direc#iilor de cercetare ce vor fi urmate de c"tre candidat.
Habilitation thesis – F. Mariasiu 5
!
!
Nomenclature
%, &, ' - Bohac model constants
!’ - isentropic bulk modulus
( - density of the sample
)* - surface strain
)U - ultimate strain rate
+ - shape factor
, - corresponding stress
,' - yield stress for the injector material
,max - maximum stress allowed for injector material.
µ - oil dynamic viscosity
µref - oil dynamic viscosity, at 40 °C
A, B, and C - constants depending on the material (Antoine equation)
Bp - bore
BMEP - brake mean effective pressure
BSFC - brake specific fuel consumption
BXXUs_irr - abbreviation where XX represents the volumetric percentage of methyl ester in
the blends with the diesel fuel.
CI - compression ignition
CN - cavitation number
CFD - computational fluid dynamics
Ccb - coefficient of the hydrodynamic losses in main bearings
Ccs - coefficient of friction losses in main bearings seals
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 6
!
!
Cp - proportionality constant (related to surface roughness)
Cpb - coefficient for connecting rod bearing hydrodynamics
Cps - coefficient for skirt-cylinder wall hydrodynamics
Cpr - coefficient for piston ring-cylinder wall
Cvb - coefficient for camshaft bearing hydrodynamic
Cvf - flat cam follower constant
Cvh - oscillating hydrodynamic lubrication constant
Cvm - oscillating mixed lubrication constant
Cvs - boundary lubrication constant due to the camshaft bearing seals
Db - bearing diameter
Eus - ultrasonic energy
FAMEs - fatty acid methyl esters
FMEP - friction mean effective power
Fmeppiston - piston group friction mean effective pressure
Fmepaux - auxiliary losses
Fmepcam - friction losses of camshaft
Fmepcrankshaft - crankshaft friction mean effective pressure
Fmepvalvetrain - friction mean effective pressure in the valve train
IC – internal combustion
IMEP - indicated mean effective pressure
K -factor dependent on the injector nozzle material
l - thickness of the hardened layer
L - maximum thickness of the hardened layer
Lb - bearing length
Habilitation thesis – F. Mariasiu 7
!
!
Lv - maximum valve lift
MDPR - Mean Depth of Penetration Rate (erosion estimation rate)
n - oil lubrication viscosity index
nb - number of bearings
nc - number of cylinders
nss - stress–strain relation exponent
nv - number of valves
N - engine speed
Ni - impacts per unit area
NOx – oxides if nitrogen
OHV – overhead valvetrain
pinj -pressure at the inlet of the nozzle
pout - pressure at the outlet of the nozzle
pvap - vapor pressure
pvap_i - vapor pressure of the ith pure of xi FAME component
pvap_mix - total vapor pressure of the mixtures
Pus - ultrasonic power
RME - rapeseed methyl ester
R-PVO - rapeseed pure vegetable oil
s - speed of sound in fluid
S - stroke
Si - size of the impact loads
t - time
T – temperature
Vp - piston average speed
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 8
!
!
VBD - volume of irradiated biofuel (biodiesel)
VOF - volume-of-fluid
u - speed of sound
W – energy
WD- wheel drive
Habilitation thesis – F. Mariasiu 9
!
!
1. CONTEXT OF HABILITATION
The process of habilitation is based on modern and contemporary need to improve
processes that characterizing higher (academic) education, through the educational,
research and institutional components, at the level of each staff member (or functional
entities) of higher education institution structure.
Details of the educational and research route (path) provide necessary information to
identify existing competences and skills, with potentially in determining individual
complementarity of candidates with academic environment.
Habilitation process provides a snapshot of academic career by nominating and
outlining past, current and future directions in candidate’s professional activities; and further,
help to correlate these activities, with the overall institutional development directions of the
department and/or the university.
Obtaining the certificate of habilitation will be for each member of the academic
community (committed and connected requirements contemporary academia), in a defining
manner, a tool to be used, constantly updated and adapted to modern trends and
requirements of science education, research activity and economy.
Realization and completion of all these activities should be viewed in terms of
increasing the efficiency of teaching (and transmission) to PhD student of the mandatory and
specific competences and skills require by research’s activity and management.
Beside those mentioned above, the context and necessity of habilitation is strongly
conditioned by following issues:
• Mandatory conditions imposed by Technical University of Cluj-Napoca’s internal
methodology to obtain the title of professor
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 10
!
!
• Necessity and willingness to transfer the accumulated knowledge in scientific
research and also the knowhow in management of research activities to younger
researchers
• Demands from former students to continue at PhD level the developing of ideas,
problems and researches studied already for bachelor and/or master thesis.
Habilitation thesis – F. Mariasiu 11
!
!
2. RESEARCH DIRECTIONS AND COMPETENCES
The characterization of candidate’s research activity is a multi- trans- and inter-
disciplinary one, with the main goal of investigating the limitations of biofuels use in internal
combustion engines and to offer proper (and also applicative) solutions to improve their use.
The complexity of research activity is given by the numerous factors of influence
responsible of possibilities to optimize the internal combustion engines when biofuels are
used. The influences of biofuels physico-chemical characteristics were studied in aim to
improve engine’s performance in terms of: energetic efficiency, pollutant emission (especially
NOx pollutants) and friction losses (Figure 1). Each research was finalized by offering a
proper and/or applied solution (patent application).
Figure 1. Major direction of researches
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 12
!
!
The approaches on this particularly issues need to use complex a combined
knowledge from different domains:
• Thermodynamics, Physics - the analysis of combustion processes inside the
combustion chamber of an internal combustion engine;
• Chemistry - determining mechanisms and formation influence factors of pollutants
classes in exhaust gases emitted into the atmosphere by internal combustion engines;
characterization of biofuels properties.
• Mechanical - establishing optimal operating points considering the ratio effective
power / emissions level, in the operation of internal combustion engines
• Tribology and Wear – identifying the magnitude of friction and the possibilities to
reduce the engine’s mechanisms wear, to increase overall the engine efficiency.
• Mathematics, Statistics and Computer Simulation - setting theory and mathematical
structure of the models; determine the dependency relations; analyses of experimental
data.
• Management - management of the research projects (and related activities)
• Experimental techniques - use of modern equipment and instrumentation to identify
the parameters that govern the important processes in the formation and emission of
toxic and carcinogenic pollutants
• Environmental issues – modern experimental techniques for investigating pollutant
emissions
• Human healthcare – assessments on pollutant emissions effects on humans.
Those necessary multidisciplinary competences, skills and knowledge were developed
by candidate since PhD graduation (2003) and used in candidate’s research activity, trough a
permanent training and education.
The competences and skills of candidate can be summarized as follow:
1. Professional
a) Advanced knowledge and skill in IC engines functional processes
b) Advanced knowledge and skills in IC engine simulation
c) Capacities and abilities of identification, definition and solving of specific
problem in IC engines processes in general and in pollutant emissions
Habilitation thesis – F. Mariasiu 13
!
!
processes in particularly
d) Advanced skills in modern research methods and methodology for optimal
design, modelling, analysis and experimental testing of IC engines
2. Educational
a) Information and knowledge transfer to students
b) Implication of colleagues and students in research and educational activities
c) Analyse of students’ demands, perceptions and assessments on educational
program
d) Use of TIC and blended learning in teaching and educational activity
3. Transversal
a) Very good abilities in personal and inter-personal communication
b) Proactive approach of problems
c) Good abilities in human and material resources management
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 14
!
!
3. RESEARCH ACTIVITIES AND RESULTS
The research topics addressed by the candidate are topics of nationally and
internationally interest, through research and studies on the possibilities of integration and
widespread use of renewable resources in energy production.
In particular, due to education, knowledge and expertise of the candidate, those
research (and educational) activities aimed further, novelty and original possibilities to
increase the energy efficiency of internal combustion engines and also the possibilities on
large-scale use of biofuels in internal combustion engines fuelling.
The major challenge in candidate research activity was the successful completion of
PN II Idei Exploratorii ID 175 project, as project manager (director). The project theme
regarded the investigation on external energy apply effects on internal combustion engines
fuelled with biofuels. The accumulated experience and new directions open in candidate’s
research activity from this project, has enabled to continue research in this field, but (perhaps
more importantly) helped to mature process of candidate as researcher.
Taking into consideration the objective demands of Romanian educational system, the
research activity is closely correlated with educational and academic activity. The
dissemination activities of research’s results were done to national and international scientific
community and also to the colleagues and students.
The results of research and educational academic activity can be summarized as:
• 4 text books as single or first author
• 4 text books as co-author
• 1 e-learning course (“The management of transport vehicles’ engines”-
DIDATEC E-learning platform)
• 41 scientific articles as single/first author and co-author of 35 scientific articles
presented at national and international conferences and symposiums and/or
Habilitation thesis – F. Mariasiu 15
!
!
published in scientific journals (10 indexed in ISI-Thompson and ISI-
Proceedings; 28 indexed in international database (Web of Science, Scopus,
Google Schoolar, Fisita, CABI, Copernicus, EBSCO, ProQuest), 12 citations)
• 1 national research grant as director and 8 as team member
• 1 European funded project as short-term expert
• 7 articles published in mass media journals (related to the specific of biofuels
research)
• Main author of 2 patent applications (RO 127 032-A2, "Cold start device of
internal combustion engines fueled with biodiesel" and RO 128 768-A2,
"Device to reduce lubricating oil viscosity for internal combustion engines start
at low ambient temperatures ")
• Coordinator of more that 150 bachelor and master thesis
• Coordinator-professor of students participating to Rexroth/Aventics Pneumobil
Race contest (2009-2015) – air-powered prototype vehicles.
The competences, abilities and skill s accumulated by candidate trough entire period of
research activity offer opportunities to collaborate with national and foreign researchers.
Strongly contacts were made with researchers from abroad:
• Germany (prof.dr. Stefan Stolte – University of Bremen, Centre of
Environmental Research and Sustainable Technology (UFT); dr. Dana
Kralisch - Friedrich-Schiller-University Jena)
• Austria (Prof. Dipl. Hans-Georg Frantz MPBL - FH JOANNEUM, Kapfenberg)
• Norway (dr. Otto Andersen – Stiftinga Vestlandsforsking/Western Norway
Research Institute - WNRI, Sergio Manzzeti – Fjordforsk A.S.)
• Slovakia (Dr Pavol Hvizdos - Institute of Materials Research\Slovakia
Academy of Science)
• Slovenia (Dr. Ema Zagar - Head of Laboratory for Polymer Chemistry and
Technology, National Institute of Chemistry)
• Swisserland (Dr. Nabil Ouerhani, Institut des Systèmes Interactifs et
Communicants-ISIC-Arc, Neuchatel)
• Hungary (Dr. Brigitta Bodzay - Budapest University of Technology and
Economics)
• Estonia (assoc. prof. Hans Orru - University of Tartu)
• Russia (prof.dr. Vladimir Vilorievich An, prof.dr. Yuri Borisov, prof.dr. Valery
Perminov – Tomsk Polytechnic University)
• Serbia (prof.dr. Lazar Savin – University of Novi-Sad)
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 16
!
!
• Poland (dr. Anna Kowalska – Wroclaw Institute of Technology)
, and at national level:
• National Institute for Research and Development and Environmental
Protection (INCDPM) - Bucharest
• Ceprocim SA - Bucharest
• Research Institute Ceprocim SA - B Bucharest
• Agricultural Science University of Banat - Timisoara,
• University of Oradea.
The collaboration with above presented colleagues was under form of participation in
joint research teams for ERA NET, CNCSIS and SEE calls proposals and co-authors of
scientific articles (in progress).
Considering that professional training is required to be performed continuously for up to
date with the latest news and findings in research activity, the candidate participated at
national and international scientific conferences and symposiums, as well as, followed
postgraduate training courses:
• To use modern equipment for IC engines testing procedures (AVL -
2010/2011)
• To use and apply of modern means and techniques in education
(DIDATEC - 2010/2013)
• To use modern methods in management (Southern Connecticut State
University (USA) and Leader XXI Foundation - 2004/2005)
• Certificated as Project Manager for projects financed with European
funds (CNFPA - 2010).
The results of research carried out on possibilities to increase the use of biofuels, were
awarded by:
• Award for research activity UEFISCDI - PN-II-RU-2382 PRECISI- 2013-
7-2382 program (Romanian Executive Unit for Financing of High
Education, Research, Development and Innovation).
• Diploma of Excellence and the Gold Medal at the International
Habilitation thesis – F. Mariasiu 17
!
!
Exhibition of Research "ProInvent 2014" Cluj-Napoca, Gold Medal at
the International Exhibition "Inventica 2014" Iasi and Silver Medal at
International Exhibition "Inventika" Bucharest 2014, for patent
application RO 127 032-A2, "Cold start device of internal combustion
engines fueled with biodiesel", authors: Mariasiu F., Burnete N., Varga
B.
• Award of Excellence at the International Exhibition of Research
"ProInvent 2012" Cluj-Napoca for patent application RO 128 768-A2,
"Device to reduce lubricating oil viscosity for internal combustion
engines start at low ambient temperatures ", authors: Mariasiu F., Varga
B., Deac T.
The candidate activate as editor inside editorial group for Central European Journal of
Engineering (Energy & Fuels domain), and as reviewer for several mainstream scientific
journals: Energy Conversion and Management, Tribology Transactions, Transport, Annals of
Operational Research, Central European Journal of Engineering, African Journal of
Agriculture Research, International Journal of Energy Technology and Policy.
As can be see, both research and educational activity of candidate demonstrate the
competences, abilities and skills necessary to confirm the habilitation process (obtaining the
habilitation title), process can be considered further to be a stimulant for continues the
academic activity on higher standards.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 18
!
!
4. CONTEXT OF RESEARCH WORK
4.1. NECCESITY AND CONTEMPORARY CONTEXT OF RESEARCH ACTIVITIES
Contemporary society is fully characterized by the concept of 'mobility'. Mobility of
ideas, people and goods requires a high dynamic of vehicle use in everyday life by
human society. Unfortunately with the use of motor vehicles (as means of transport)
there are immediate problems related to environmental pollution, caused by pollutant
emissions from the combustion of fuels.
Transportation sector is currently responsible for over 20% of the emission of
greenhouse pollutants, emission that directly affect climatic conditions of the planet.
Increased emissions in conjunction with achieving maximum degree of natural
regeneration of the environment, leading to serious problems related to pollution.
Naturally, the European Union (mainly) occurred policies and actions to reduce
emissions from activities associated with human society.
As an immediate energetic solution to reducing atmospheric pollution caused by
compression–ignition (CI) engines, biofuels offer (with some limitation) a viable
alternative to fossil fuels due to their renewable characteristics. Also, the use of biofuels
is considered to be the short-term solution, until new proposed technologies (e.g. electric
vehicles) will be mature. Starting from this premise, the European Union establish
mandatory regulations that stipulate the use of min. 10% of biofuels in blends with fossil
fuels (dead line for members to implement the EU Directive 2009/28/EC is 2020 year -
[17]).
Habilitation thesis – F. Mariasiu 19
!
!
Figure 2. The renewable character of biofuels
In addition to the advantage afforded by closing the natural CO2 life cycle (Figure 2),
utilization of biofuels for powering internal combustion engines is immediately possible
without major structural changes to the engines and fuel distribution network. In
transportation domain, standards and regulations related to exhaust emissions, are
becoming increasingly stringent, relative to the maximum quantity of exhaust gases,
which is accept to be emitted into the atmosphere, from the operation of an internal
combustion engine. The adoption of constructive solutions to achieve this goal it is
absolutely necessary but not sufficient (due to economic efficiency).
Therefor, due to the complex characteristics and particularities of a internal
combustion engine functioning, it is necessary to conduct complementary studies and
researches related to the occurring processes in internal combustion engines and their
optimization (by increasing energy efficiency) for lowering emissions level, in case of
biofuels use.
The issues related to the specific conditions of internal combustion engines
processes (and their subsequent effects) is require today an immediate, novelty and
original approach, but using good scientific arguments, modern and efficient methods
and approaches (but also unconventional) in research activity. Based on these premises,
were crystallized, developed and maintained the scientific activity of the candidate, with
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 20
!
!
the major purpose of investigating any possible improvement in operation of internal
combustion engines fuelled with biofuels. The detailed directions of candidate researches
and results will be presented in following chapters, based on the articles published by
candidate in ISI Thompson indexed journals and on patent applications.
4.2. POSSIBILITIES TO INCRESE BIOFUEL’S POTENTIAL USED IN INTERNAL COMBUSTION ENGINES FUELLING
The researches of candidate related to identify direct actions to improve energetic
efficiency of compression ignition (CI) engines and also to reduce pollutant emissions, were
done trough complex analysis of factors of influence (both, qualitative and quantitative) by
biofuels use in CI engines fuelling. The studies and researches were conducted at:
A) Microscopic level (effect of biofuel characteristics on nozzle injector
cavitation process)- modern approaches trough CFD simulation techniques.
B) Macroscopic level (effect of applied ultrasonic external energy on biofuels
physico-chemical characteristics and reduction of engine friction losses) –
unconventional approaches trough ultrasounds use.
4.2.1. Effects of biofuel characteristics on injection process1
It is widely know that, biofuels can be used both in the form of methyl esters (and/or
mixed with diesel fuel) and as pure vegetable oil (PVO) to fuelling a compression ignition
engine (diesel engine). However, there are problems with cold engine starts (caused by their
lower energy content, higher viscosity, and cloud point value) and their high emissions of
NOx compared to fossil fuels. The NOx emissions are high due to both the existence of
oxygen in the molecular composition of biofuels as well as the particular issues created by
the characteristics of the fuel injection process of compression ignition.
The density of high viscosity of biofuels result in a poorer quality fuel spray in terms of
jet breakup, penetration, and atomization, with direct effects on functional performance and
engine emissions (compared to petro diesel [39]). In particular, fuel atomization !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!"!#$%&!'()$*!+,-!.(/0()012!34!567"89!:1;$/0<(=!>,?$)&0@(&0+,!AB!#C$!DBB$<&)!AB!E0+B1$=!FC(/(<&$/0)&0<)!A,!#C$!>,G$<&+/!:+HH=$!D/+)0+,!I/+<$))J2!#/0'+=+@K!#/(,)(<&0+,)!LM569-!"M"N"MO4!
!
Habilitation thesis – F. Mariasiu 21
!
!
characteristics depend on both the injection processes (pressure, timing, rate [58]) and the
geometric characteristics of the injector nozzle (orifice discharge coefficient, inclination angle
of the nozzle hole, radius of the inlet of the nozzle orifice, diameter of the nozzle exit [83],
[85]). Experiments conducted by Gavaises and Andriotis [20], He and Ruiz [26], Nurick [50],
and Tamaki et al. [71] showed that nozzle orifice erosion due to cavitation can lead to
negative changes in fuel jet temporal development and directly influence the performance of
the engine’s injection process.
Many scientific papers have studied the cavitation phenomena, in terms of
mathematical model development (to accurately describe the many processes and factors
that influence the particularities of cavitation flow), computer simulation, or physical models.
From the point of view of theoretical considerations, according to the assumption of
Giannadakis [22] and Giannadakis et al. [23], cavitation phenomena are attributed to the
dynamics of small bubble nuclei, which are nucleated in the liquid after certain criteria are
met. Further, the cavitation bubbles, influenced by direct interaction with the liquid flow, break
up and coalescence, especially in the case of a nozzle injector (characterized by very high-
pressure injection, short injection rate, and small orifice discharge coefficient).
From the early experiments of Badock, et al. [3] it was found that the cavitation number
(CN) is independent of the Reynolds number and can be calculated using Eq. (1):
!" ! !!"#!!!"#!!"#!!!"#
(1)
, where pinj is the pressure at the inlet of the nozzle, pout is the pressure at the outlet of the
nozzle, and pvap represents the vapor pressure. Research in the cavitation domain has
shown that calculation of the cavitation number is not sufficient to characterize the fluid flow
[45], [46]; flow scale effects (associated with the imperfect micro- and macro-geometry of the
flow [59]) and liquid quality (in particular the viscous nature of the flow [81]) affect the quality
prediction of cavitation characteristics of fluid flow.
Roosen et al. [59] and Winklhofer et al. [81] showed that the cavitation of fluids is
characterized by the same strain rates but different viscosities and reported that they found
differences between calculated (predicted) and experimental results. Furthermore, they
showed that the shear stress mechanism of cavitation is consistent with the measurements
of cavitation flows in liquids with different viscosities. As Qu et al. [56] showed, the modern
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 22
!
!
and advanced heavy-duty diesel fuel injection system will be required to operate at higher
pressure and temperatures and with fuels that have poorer lubricity (the ability to reduce
friction between moving parts in a machine or mechanism). These characteristics indicate a
greater probability for cavitation phenomena with a direct influence on fluid flow
characteristics [37], [80].
Therefore, this work presents the results of computational fluid dynamics (CFD)
simulation concerned with the erosion phenomena in the injector nozzle for different types of
biofuels, considering that are important differences between the viscosities of petro diesel
fuels and biodiesels [39], [40].
Starting to the computational model considerations, the CFD cavitation model
implemented in the FIRE software package (AVL Advance Simulation Technologies [1]) is
based on a Eulerian-Eulerian approach and is suitable for the presented injector orifice type
and the considered conditions of functionality. Multiphase flow can be simulated in this way
because each individual fluid is considered as a continuous phase, and conservation laws
are applied for each fluid. The Eulerian-Eulerian approach is capable of handling an arbitrary
number of phases and allows the use of the following complementary models [1]:
• Homogenous (equilibrium) model—a volume fraction equation is calculated
for each phase but only a single momentum r equation is calculated because
the phases are assumed to be in momentum equilibrium.
• Multi-fluid model—the complete set of the conservation equations for each
phase is considered for calculation. These equations are coupled through the
interfacial interactions derived through an averaging process.
• Volume-of-fluid (VOF) free-surface model—based on solving the VOF
equation using a higher order discretization scheme and used for capturing
sharp interfaces of immiscible fluids.
The multi-fluid model was adopted to simulate multiphase flow, because offer the
possibilities to calculate a complete set of conservation equations (momentum and energy),
for all phases by coupling through the interfacial interaction derived through the averaging
process. For brevity, further details of the physical model and governing equations can be
found in AVL Advance Simulation Technologies documentation [1].
Using the above considerations, the FIRE software package was applied to simulate
the flow of fuel in injection nozzles in IC engines. In addition, the Eulerian approach can be
adopted for application where the bubble collapse process induces erosion damage through
a moment method by solving the bubble number density (average number of bubbles per
Habilitation thesis – F. Mariasiu 23
!
!
unit volume) equation and the interfacial area density equation [6], [18].
The erosion process model implemented in the FIRE software package is based on
the work of Berchiche et al. [6] and Franc and Riondet [18]. The erosion estimation rate is
given by:
!"#$ ! !! ! !! ! !! ! !! ! !! ! ! !!!!
!! ! ! (2)
where Ni, Si, and L are the impacts per unit area (1.9-1011), the size of the impact loads
(1-10.9), and the maximum thickness of the hardened layer (2-10.3 m), respectively. The
theta factor (+ = 3) is considered the shape factor and )* and )U are the surface strain and the
ultimate strain rate related to the corresponding stress , by Eq. (3):
! ! !! ! !!!!! (3)
In Eq. (3) ,' is the yield stress for the injector material (4-108 Pa), K is the K-factor, and
nss = 0.5 is the stress–strain relation exponential. The K-factor depends on the injector nozzle
material dependent (K = 8.64-108 [1]).
The surface strain rate )* can be obtained by considering the energy law of
conservation and considering the thickness of the hardened layer (l = 2-10.4 m):
( )( )!"#
$%
&
++++
+''=
(()
(
*)) +
nnKSlW
n
111)(
(4)
After the incubation period, at steady state (the number of bubbles follows a linear
growth law and the erosion rate has a constant value—the material removal rate reaches
steady state, represented by Mean Depth of Penetration Rate [MDPR]), the system energy is
considered to be:
( ) ( ) ( )Ul WWW !!! +=' (5)
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 24
!
!
where )l is computed with the strain rate stress estimated by Eq. (6):
!"
#$%
&'(
)*+
,= max,min -.-dt
drsC bubblelpl
(6)
! The coefficient Cp = 1 is the proportionality constant (related to surface roughness), s is
the speed of sound in fluid (Table 1), and ,max = 8.64-108 Pa is the maximum stress
allowed for injector material.
Using as a mean indicator, the MDPR, it is possible to indicate how the cavitation
process influences the material erosion. Considering the incubation time of the cavitation-
type flow, the MDPR (as a function of the impact rate, impact size, and material properties)
take into consideration geometrical changes as a result of material erosion due to cavitation
and, hence, their effect on the fuel spray behavior in the combustion chamber [9], [61].
In order to investigate the effect of fuel characteristics on nozzle erosion phenomena,
three different fuels were considered: diesel fuel, rapeseed methyl ester (RME), and
rapeseed pure vegetable oil (R-PVO). The characteristics of the fuels used and the main
boundary conditions of the computational simulation to determine the erosion process are
presented in Table 1.
The boundary conditions specify the physical properties of the faces on the volume
mesh. The boundaries of the volume mesh include the inlet, outlet, and wall boundary.
Considering the particularities of the cavitation process, boundary conditions will require
specification for two phases (liquid and gas). For both phases, the inlet boundary conditions
turbulent kinetic energy and turbulent length scale were adopted as 0.1 m and 0.001 m2/s2,
respectively.
For the outlet boundary condition the fixed volume fraction was adopted for the liquid
phase (0.999) and the gas phase (10.6). To define the wall boundary condition the velocity
components were all set to zero and the temperature was considered to be 293.15 K.
The model was discretized using least square fit method to calculate the derivatives
and considering both phases, the following under relaxation factors were adopted:
momentum = 0.3, pressure = 0.1, turbulent kinetic energy = 0.15, turbulent dissipation rate =
0.15, energy = 0.8, and mass source = 1.
Habilitation thesis – F. Mariasiu 25
!
!
Table 1. Simulation conditions for fuels
Parameter Diesel fuel
(Diesel)
Rapeseed methyl ester
(RME)
Rapeseed pure vegetable oil
(R-PVO)
Density
[kg/m3] 830 a 880 a 890 a
Dynamic viscosity
[x10-3Ns/m2] 2.14a 4.61a 6.31a
Saturation vapor
pressure
[kPa]
892b 0.923c 0.996c
Sound speed
[m/s] 1370a 1415a 1502a
Fuel temperature
[K] 293.15 293.15 293.15
Bubble number density
(x1011) 1.9 1.9 1.9
Critical distance of
bubble collapse
[x 10-6m]
5 5 5
a-[40]; b-measured; c-calculated from Eq.7-8.
Pressure boundary conditions were considered for the inlet and outlet of the injector
nozzle. The pressure at the inlet of the nozzle was set to 500 MPa (at injected fuel
temperature of 293.15 K), and the outlet pressure was set to 5 MPa. The vapor pressures for
the cavitation mass exchange for the considered fuels are presented in Table 1. Because the
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 26
!
!
RME and R-PVO are a mixture of many fatty acid methyl esters (FAMEs), the total vapor
pressure of the mixtures could be calculated using Raoult’s law, defined as Eq. (7):
! "=i
iivapmixvap xpp __ (7)
where pvap_i and pvap_mix are the vapor pressure of the ith pure FAME and the mixture,
respectively, as research methodology presented and used by Yuan et al. (25).
For each FAME component, the vapor pressure was calculated based on the work and
results of Mariasiu et al. [40], Yuan et al. [84], and Goodrum [25], using the Antoine equation
as defined in Eq. (8):
CTBApvap +
!=)log(
(8)
, were A, B, and C are constants depending on the material and T is temperature.
For numerical investigation of cavitation and erosion processes in a nozzle injector, a
VCO-type multihole injector was considered. The geometrical model and characteristics were
built into the computational model, presented in Figure 3. Because the injector holes were in
a symmetric distribution along the axis of the injector and because they were also in a
circumferential distribution, for the computational simulation a 30o segment model was
adopted. The moving grid was built to achieve a mesh of about 180,500 cells. The hole was
meshed with 116,448 cells (with an average size of 3 µm). The body and the rest of the sac
were meshed with 74,564 cells. The domain of the constant-volume vessel was built from
approximate 400,000 cells, characterized by a constant mesh size of 0.30 mm.
The sector angle of the nozzle flow simulation was considered to be at 180o, and the
angle between the axis of the cylindrical nozzle and the injector cone was 75o. The length
and exit diameter of the nozzle were 1.05 and 0.22 mm, respectively. The injector model was
based on a joined moving mesh type considering the movement of the injector needle in the
injection process, according to observations made by Ngondi et al. [49], to improve the
quality of the results (Figure 4).
Habilitation thesis – F. Mariasiu 27
!
!
Figure 3. Computational segment model.
Figure 4. Injector needle movement law
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 28
!
!
Table 2. Spatial coordinates of injector nozzle computational model
Parameters Coordinates [m]
x y z
Nozzle direction 0 1 0
Hole center -5.1·10-5 -1.09·10-4 0
Hole direction (spray axis) 1.65·10-4 -4.4·10-5 0
To improve the input data from the simulation model, the movement of the injector
needle law was correspondent to the experimental data achieved from the engine test bed;
the values were averaged from 100 sets of data.
The simulation time for the cases considered was set to 2.5 ms with a maximum
injector needle lift of 0.5 mm. Spatial coordinates that define the nozzle position are
presented in Table 2 and Figure 3.
For the simulation process, the convergence criteria considered a maximum of 500
iterations and a minimum of 5 iterations. Normalized residuals were 0.001 for pressure and
momentum and 0.005 for turbulent kinetic energy.
Considering the results and observations of Som et al. [67], two models were adopted
for the injection spray development in a combustion chamber. To predict the spray evolution,
the Kelvin-Helmholtz-aerodynamic cavitation turbulence model (KH) for primary liquid
breakup and the Kelvin-Helmholtz-Rayleigh-Taylor model (KH-RT) for secondary droplet
breakup were used [1].
For model validation, the simulation results were compared with the experimental data,
considering two important characteristics of jet fuel (penetration length and cone angle).
Experimental data were obtained from experiments performed on an engine test stand
developed by AVL GmbH (Graz, Austria). The experimental stand consists of an AVL 5402
optical diesel engine, single cylinder, direct injection with common rail injection (1,800 bar
maximum injection pressure (AVL List GmbH, Graz, Austria)), Bosch CR1 injector, bore 85
mm, stroke 90 mm, con rod 138 mm, 17.5 compression ratio, and ETAS ETK 7.1 ECU
engine management system.
Habilitation thesis – F. Mariasiu 29
!
!
An AVL Visioscope system was used for video acquisition of fuel spray development
inside the combustion chamber and an AVL rapid prototype electronic management system
was used to record the movement of the injector needle law.
Table 3. Average values of considered erosion and cavitation indicators
Parameter average
value
Fuel density [kg/m3]
830 880 890
MDPR
[x 10-12m/s] 6.65 6.31 5.88
Turbulence kinetic energy
[m2/s2]
16436.01 16179.81 16127.17
Velocity at nozzle exit
[m/s]
876.63 699.36 657.25
The results from the computational simulation were focused on the erosion processes
developed in the volume of a nozzle injector, which are graphically presented only for three
positions of moving injector needle, corresponding to 0.0055, 0.0083, and 0.011 s from the
start of the injection process (Figure 5). Validation of the model was performed by
comparisons with experimental results considering the spray length penetration and cone
angle.
Erosion process that characterized the flow regimes was evaluated in terms of the
MDPR factor, turbulence kinetic energy, and nozzle exit velocity. The turbulent kinetic energy
was higher for petro diesel fuel, and all simulated fuels presented peak values (17,663 m2/s2
for diesel, 17,474 m2/s2 for RME, and 17,377 m2/s2 for R-PVO) at 1.67 msec from the start of
the injection process (Figure 5).
The effects of the fuel characteristics on the magnitude and spatial development of the
cavitation process are presented in Figures 6 and 7.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 30
!
!
The values of the MDPR factor increased gradually to maximum values of 1.30-10.11,
1.20-10.11, and 1.10-10.11 m/s for the simulations using diesel fuel, RME, and R-PVO,
respectively. It can be seen (Figure 7) that the erosion process developed up and down the
volume of the injector nozzle entrance (considering the axial axis of the nozzle injector) with
a maximum area (and magnitude) of development with regard to the petro diesel fuel.
The differences in magnitude of MDPR between the simulated fuels were smaller at the
start of the injection process (.3.76% for RME and .13.69% for R-PVO compared to diesel
fuel) than at the end of the injection process (.7.69% for RME and .15.38% for R-PVO
compared to diesel fuel). The same tendency was observed for the fuel velocity at the nozzle
exit (Figure 8). At the end of the injection process, the differences between the values
(664.06 m/s for diesel, 353.92 m/s for RME, and 263.04 m/s for R-PVO) were much higher
than those determined at the start of the injection process (1,089.8 m/s for diesel, 1,056.7
m/s for RME, and 1,050.1 m/s for R-PVO).
The average values of the parameters investigated using CFD simulation for the
whole injection process are presented in Table 3; these values highlight the differences
between the fuels. The variations in the considered indicators (erosion, turbulent kinetic
energy, and velocity at nozzle exit) are presented for all injection periods in Figures 9–11.
The magnitude of the injector nozzle cavitation erosion process was greater for diesel fuel
compared to RME biodiesel and R-PVO (+5.11% and +11.57%, respectively). The
turbulence kinetic average values were not very different depending on the fuel considered.
Variations in turbulence kinetics for RME and R-PVO cases were .1.56 and .1.88%
lower than for diesel fuel, respectively. A .20.22% difference between biodiesel (RME) and
diesel fuel and a .25.02% difference between R-PVO and diesel fuel was recorded from the
velocity magnitude at the nozzle exit. Considering the above-presented results, the effects of
cavitation strongly influenced the magnitude of nozzle exit velocity for RME and R-PVO
(compared to diesel fuel).
The field of speed uniformity at the exit of the injector nozzle using RME and R-PVO
(compared to diesel fuel) explained the differences between the spray structures, differences
already presented in previously published experimental research [15, 44, 60, 65].
Habilitation thesis – F. Mariasiu 31
!
!
Figure 5. Turbulent kinetic energy along the nozzle axial direction.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 32
!
!
Figure 6. Variation in MDPR parameter (top view).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 34
!
!
Considering the results presented in Figures 9–11, the following observations can be
made: The fuel injection velocity at the nozzle orifice exit is an important parameter with
further influence on spray development in the combustion chamber being directly influenced
by cavitation process. The differences in injection velocity patterns (Figure 11) also influence
the fuel mass rate flow rate at the orifice exit. For the same injection period (compared to
diesel fuel), a lower quantity of biodiesel (RME and R-PVO) is injected in combustion
chamber. This can explain the lower engine effective power when biodiesel is used.
Figure 8. Velocity pattern at the injector nozzle exit.
Habilitation thesis – F. Mariasiu 35
!
!
Figure 9. Erosion estimation rate variation vs. fuel density.
Figure 10. Turbulence kinetic energy variation vs. fuel density.
From the point of view of turbulence kinetic energy at the nozzle exit, the average
values were also lower for biodiesel (compared to diesel fuel) as a direct influence of lower
Reynolds number (due to higher viscosity). The differences in turbulent kinetic energy values
and patterns have direct implications for spray development and characteristics. The
turbulent kinetic energy pattern at the orifice exit influences the primary breakup and the
spray penetration length. The biodiesel spray has more homogeneous structure and drop
size. Thus, the biodiesel droplets agglomerate quickly, leading to greater penetration of the
jet inside the combustion chamber.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 36
!
!
Figure 11. Magnitude of fuel velocity at the nozzle exit vs. density.
Figure 12. Comparison between simulation and experiment for RME spray development.
Figure 12 presents the spray penetration (development) in the combustion chamber for
RME fuel, in a comparative presentation of experimental and computational results (as an
Habilitation thesis – F. Mariasiu 37
!
!
example to validate the computational model). The computer simulation of a spray jet
showed the tendency of RMS fuel drops to agglomerate as a direct effect of exit nozzle
velocity pattern and values.
The spray penetration length predicted from simulation considering (not considering)
the influence of cavitation was 0.74% (.1.48%) for diesel fuel and 1.8% (.2.45%) for RME
compared to the experimental results (Figure 13). The differences for the cone angle
between predicted and experimental results considering (not considering) the influence of
cavitation were 2.27% (.3.64%) for diesel fuel and .1.02% (4.06%) for RME (Figure 14).
The results obtained from computer simulation were consistent with the experimental
results that showed that the penetration length was higher for RME (R-PVO) fuel corroborate
with a smaller spray cone angle than diesel fuel (and confirmed the results of other
researchers, including Som et al. [67] and Wang et al. [78, 79]), leading to the conclusion
that in the future simulations the effects of cavitation on spray behaviour must be taken into
consideration.
Figure 13. Measured and simulated fuel spray liquid length penetration.
!
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 38
!
!
Figure 14. Measured and simulated fuel spray cone angles.
As a major conclusion, the results obtained by CFD simulation confirmed the direct
effects of fuels’ physical properties on the phenomenon of injector nozzle cavitation and
erosion, with immediate influence on the quality of jet fuel, emissions, and operational
performance of CI engines.
The effects were highlighted by the differences in MDPR, turbulence, and nozzle exit
velocity for the cases studied.
The lower magnitude of the cavitation process and turbulence intensity for RME and
R-PVO fuels (compared to diesel fuel) was the direct effect of lower vapor pressure and
greater viscosity, respectively, of biodiesel fuels. The immediate effects at the nozzle exit
were highlighted by the higher spray penetration, poor primary breakup process, and smaller
cone angle with biodiesel use.
It can be said that the cavitation process and related turbulence generated inside the
injector nozzle (using different types of fuels) influence the spray jet. The influences are
present in the atomization process, initial velocity, primary breakup process, and spray
penetration. All of these influences of the biodiesel injection process require changes, new
visions, and new solutions for designing on piston bowl, injection strategy, and initial bowl
swirl ratio to optimize the efficiency of the biodiesel combustion process.
Habilitation thesis – F. Mariasiu 39
!
!
4.2.2. Effects of external energy (ultrasonic) application on biofuel use performances2
It is widely accepted that biodiesel is one of the current solutions in an attempt to limit
the effect of IC engines greenhouse emissions. Effectuate researches until present [31, 32],
confirms that increasing the percentage of methyl ester in diesel-biodiesel blends lead to a
greater reduction of CO2 emissions (comparative with diesel fuel), but biodiesel and biodiesel
blends have been shown to have higher NOx pollutant emissions than petroleum diesel (with
direct and immediate influence on human health).
The pollution caused by nitric oxides emissions is capable to forming a variety of
cytotoxic species, which contribute to lung pathology and disease, with implication in
pathogenesis of acute respiratory distress syndrome [77].
Nabi and Hustad [48] and Zhu et al. [86] shown that in case of biodiesel use for
fuelling diesel engine, emissions of NOx increase by 2 - 4% (for B20 blend) as much 12-20%
(for B100). The biodiesel NOx specific increase effect is related to the differences in physico-
chemically characteristics (viscosity, density, bulk modulus of compressibility, bond structure,
and cetane number), fuel injection timing and spray characteristics, and engine operation
condition, with major influences on the combustion process [30,47].
The differences between the physical properties of methyl ester based biodiesel and
diesels are major [33] and some are presented in Table 4. These differences lead to
difficulties in using biodiesel in high blends (> 30%) with diesel fuel in existing compression
ignition engines [29, 52, 54].
One way to improve the physical parameters of biodiesel (to reduce the pollutant
emissions) is to use external energy transfer irradiation with different sources (ultrasound,
microwaves, infrared waves, ultraviolet, etc.). Some of these energy sources are able to
modify at the micro molecular level the chemical structure of the biodiesel, with immediate
influence on its physical properties [16, 34, 68]. Ultrasonic irradiation is able to make these
changes due to the phenomenon of cavitation, which takes place through the interaction of
ultrasound waves with the molecular structure of the biodiesel [27, 68, 82].
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!6!#$%&! '()$*! +,-! .(/0()012! 34! 567"P9! Q&&$;R&)! &+! /$*1<$! '0+*0$)$=! '=$,*)! :AS! R+==1&(,&! $;0))0+,)! 'K! 1=&/()+,0<! <+,*0&0+,0,@2!#/(,)R+/&!6T5"9-!P8NPT4!
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 40
!
!
Table 4. Comparative physical properties of some methyl esters with diesel fuel [40]
Fuel Density at 15° C [kg/m3]
Kinematic
viscosity at
40°C [mm/s2]
Cetane number
Cloud point
[o C]
Flash point
[o C]
Diesel fuel 841 2.7 54.1 –14 64
Rapeseed oil methyl ester
882 4.60 52.7 1 181
Soybean oil methyl ester
865 4.08 46.4 –1 168
Sunflower oil methyl ester
883 4.16 49.2 2 178
Olive oil methyl ester
881 4.18 59.8 –2 182
The models proposed by Kang et al. [27] and Mason and Lorimer [42, 43], explain the
kinetics of chemical transformations whereby the action of external energy influences the
cavitation process at the molecular level. The models describe how through the process of
ultrasonic irradiation conditioning and characteristics such as high local pressure and
temperature, substances undergo chemical reactions in two main directions:
• Pyrolysis-type chemical reactions – the transformation mechanism is
decisive in the development of a chemical high-intensity thermal effect
(local temperature can reach 5000 K) at the molecular level;
• A multiphase chemical reaction in the formation of radicals.
Availability (affinity) of hydroxyl compounds formed in the process of irradiation and
combined (being in excess in the mechanism of chemical reactions) leads to the formation of
peroxides. Peroxide formations of these groups increases the efficiency of fuel combustion
process, with beneficial influences on the further development of thermal processes in the
Habilitation thesis – F. Mariasiu 41
!
!
functional cycle of an internal combustion engine, as well as providing changes in the
biodiesel’s physical properties.
The amount of peroxide formed depends directly on the intensity and duration of the
ultrasonic irradiation process [34, 40].
The aim of the research was to provide a primary image of the processes taking
place during the ultrasonic irradiation of biodiesel. Was used experimental methods and
methodologies employed (and validated) by other researchers. For the sound of speed
measurement we used the proposed methodology of Dziza and Prusakiewicz [16], and for
determining the intensity of the ultrasonic waves we took into account the experiments
carried out by Wu et al. [82] and Gogate and Kabadi [24]. Also taken into account were the
related observations made by other researchers [51, 52, 54, 72].
The biodiesel chosen for experimentation was rapeseed methyl ester (RME), mainly
used in Europe. The samples of vegetable oil-based biofuels blended with diesel fuel used
as the subject for the experiments had the following composition:
• Fuel sample control – Diesel (diesel fuel);
• Fuel 1 – B25 (75% diesel fuel + 25% rapeseed oil methyl ester);
• Fuel 2 – B50 (50%diesel fuel + 50% rapeseed oil methyl ester);
• Fuel 3 – B75 (25% diesel fuel + 75% rapeseed oil methyl ester);
• Fuel 4 – B100 (100% rapeseed oil methyl ester).
The BXXUs_irr abbreviation was used for the ultrasonic irradiated biodiesel blends
(where XX represents the volumetric percentage of methyl ester in the blends with the diesel
fuel). The initial properties of the biodiesel were determined in laboratory conditions and are
presented in Table 5.
The variations of the physical parameters on which the experiments were focused,
were the density (determined by Anton Paar 5000 apparatus), the speed of sound passing
through the medium (Optel measuring device) and the viscosity (Haake viscometer). The
isentropic bulk modulus of the biofuels conditioned by irradiation with ultrasound was
determined by using the Newton-Laplace formula [16, 73]:
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 42
!
!
!! ! ! ! !! (9)
, where !’ is the isentropic bulk modulus (in Pa), u is the speed of sound (in m/s) and ! is
density of the sample (in kg/m3). Determination of the isentropic bulk modulus value is
significant in measuring the effect of ultrasonic irradiation on the process of ignition and
combustion of conditioned biofuels. This is because the isentropic bulk modulus value
influences the injection time. Furthermore, Tat and Van Gerpen [72], Szybist et al. [69, 70]
and Bakeas et al. [4] noted that a higher value of isentropic bulk modulus corresponded to
higher NOx values. The experiments conducted by Boehman et al. [10], Torres-Jimenez et
al. [74] confirm totally or partially this hypothesis.
Ultrasound propagation in vegetable oil and also in biofuel causes cavitation (under
specific conditions). Because of the expansion and contraction of the transfer media are
conditions to generate locally bubbles of very high temperature and of pressure (cavitation
process). As an immediate result, the physical and chemical properties of the transfer media
are modified [68].
Gogate and Kabadi [24] show that the effectiveness (efficiency) of the ultrasonic horn
in creating a cavitation effect depends on the magnitude of energy and operating frequency
supplied by the equipment. It was observed that the cavitation intensity decreases
exponentially at a specific distance from ultrasonic horn until it vanishes completely. To
create the cavitation phenomenon in the ultrasonic irradiation of biofuels for the present
experiment, we used a small volume of biofuel for conditioning (VBD=300 ml) and an
ultrasonic horn that produces 35 W/L, PZT type, at 35 kHz frequency emission, which was
applied continuously.
Measurements of physical properties considered in the experiments were carried out
after a duration of ultrasonic irradiation of 0, 100, 200, 300, 400, 500 and 600 seconds and
were compared with the values of the same physical properties of diesel fuel that was not
irradiated (sample control). The energy density transferred to the biofuel volume was
analyzed by the method proposed and used by Ramirez del Solar et al. [57] and Lee et al.
[34].
The ultrasonic power (Pus) was calculated from:
!!" ! !!"! (10)
Habilitation thesis – F. Mariasiu 43
!
!
Table 5. Physico-chemical characteristics of tested fuels
Property Diesel fuel Rapeseed methyl ester
(RME)
Chemical formula C14H30 C16-C18
Molecular weight
[g/mol] 198.4 209.6
Density
at 20oC [kg/m3] 831 879
Kinematic viscosity
at 40oC [mm2/s] 2.7 4.9
Boiling point [oC] 278 322
Higher heating value
[MJ/kg] 46.94 37.5
Carbon content
(%) 87 78.7
Sulphur content
(ppm) 233 0.036
Water content
[mg/kg] 64 86
Cetane number 54.1 52.7
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 44
!
!
, where ultrasonic energy is Eus and t is time in seconds. The Pus is constant (from the
installation construction) and therefore the energy density can be calculated using [34]:
!!" ! !!" ! !!!"
(11)
, where VBD (in ml) is the volume of irradiated biofuel (biodiesel).
For the experimental conditions described above, the values of the transferred
ultrasonic energy density in biodiesel blends are presented in Table 6. Moreover, the
ultrasonic conditioning process gives rise to conditions where peroxide compounds might
form (as oxidation mechanism of fatty acid methyl ester - FAME), resulting in a beneficial
influence on fuel combustion, but this may also have negative influence on the storage
properties of the biodiesel (especially in the long term).
To determine the influence of the instantaneous ultrasonic irradiation process on
biodiesel with regard to NOx emission, were used an experimental test bed equipped,
developed and adjusted in accordance with the methodology of the research in the field [29,
70].
The experiments were carried out to determine the differences between the emission
of NOx, for irradiated and non-irradiated biodiesel (compared with the same values for diesel
fuel) using an engine experimental test bed, presented in Figure15.
The constructive details of vessel use to ultrasonic conditioning the biodiesel blends
(patent pending) are presented in Figure 16. The engine was run at constant speed of 2400
min-1, and a Weinlich M 8000 dynamometer was also use to load the engine. The loads at
25, 50, 75 and 100% correspond to 0.10, 0.20, 0.31 respectively 0.41 MPa of BMEP.
The structural parameters and functional characteristics of the Yanmar diesel engine
L 100 AE used in the experiments are presented in Table 7.
The experimental test was performed examining the full range of engine load. The
NOx emissions were measured with a Testo 330 XL exhaust gas analyzer (with NOx
measurement cell). The calibration procedure for the gas analyzer was done before each test
(in accordance with the manufacturer’s recommendations in order to achieve measurements
errors of less than 2%). The experimental tests were performed 10 times, and the results of
those repetitions were averaged to reduce the level of uncertainty.
Habilitation thesis – F. Mariasiu 45
!
!
As research results, the biodiesel parameters considered for determining the
influence of the ultrasonic irradiation process were: speed of sound through the medium,
density, isentropic bulk modulus and kinematic viscosity. The results obtained from the
experiments are presented in Figures 17-20 (laboratory tests) and Figures 21-24 (engine test
bed experiments).
Table 6. Biodiesel blends’ physical characteristics after 600 seconds of irradiation process
Blend Density
(g/cm3)
Mean heat
capacity
(J/gK)
Ultrasonic
energy density
(kJ/L)
B25 0.836 1.958 3519.3
B50 0.853 1.978 3931.3
B75 0.862 1.981 4166.6
B100 0.876 1.993 4521.8
Figure 15. Experimental test bed structure (1 –fuel tank, 2 –pollutant emissions analyzer, 3 –injector, 4
–exhaust pipe, 5 –data acquisition system, 6 – engine speed sensor, 7 –single cylinder engine, 8 – air
intake pipe, 9 – injection pump, 10 – ultrasonic irradiation device, 11– fuel filter)
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 46
!
!
Figure 16. Constructive details of conditioning device (1-fuel-out pipe, 2-vessel,
3-cap, 4-fuel-in pipe, 5 - ultrasonic emitter)
!Table 7. Technical characteristics of test engine
Parameter Value
Type 4-stroke, air cooled,
vertical single cylinder
Bore x Stroke 86x70 mm
Displacement 406 cm3
Combustion type direct injection
Continuous rating
output
6.6 kW at 3600 min-1
Fuel injection pressure 19.6 MPa
Fuel injection timing 17±0.5o BTDC
Habilitation thesis – F. Mariasiu 47
!
!
!
Figure 17. The influence of the ultrasonic irradiation process on the speed of sound
through the medium
!
Figure 18. The influence of the ultrasonic irradiation process on the density
through the medium
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 48
!
!
Figure 19. The influence of the ultrasonic irradiation process on the
isentropic bulk modulus
!
Figure 20. The influence of the ultrasonic irradiation process on the
kinematic viscosity
Habilitation thesis – F. Mariasiu 49
!
!
As the duration of treatment increased, the overall trend for the speed of sound
variation among the ultrasonic irradiated blends was downward (Figure 17). After 600
seconds of irradiation, all values (except for B100Us_irr) were equal or smaller than the
value for the diesel fuel speed of sound.
The induced thermal effect caused by the ultrasounds interaction with the conditioned
volume of blends was measured, to determine the magnitude of the induced temperature on
biodiesel blends physical parameters characteristics. The variation is linear with the time; a
slope of 2.15oC/min, 2.21oC/min, 2.36oC/min, and 2.44oC/min was measured for the B25,
B50, B75 and respectively for B100 blend. The maximum temperature was achieve for B100
blend (42.4oC after 600 seconds of ultrasonic conditioning; initial biodiesel blends
temperature was 18oC), but according to the experiments effectuated by Bari et al. [5], a
temperature of the fuel less than 60oC, did not have a significant effect on the fuel
consumption and effective power.
For a period of approximately 420 seconds of ultrasonic irradiation conditioning, the
density of biodiesel B25Us_irr density fell below that of the diesel fuel (Figure 18). For the
other blends (B50, B75 and B100) the density decreased by an average value of –2.49 %,
but the final values were higher than those of the diesel fuel. The effect of density decreasing
is beneficial regarding the fuel injection process, with immediate consequences for the
pollutant emission levels [52].
In general, the trend of the isentropic bulk modulus variation was decreasing, with a
minimum value of –4.71 % (B100Us_irr) and a maximum of –9.68 % (B25Us_irr) (Figure 19).
Isentropic bulk modulus values dropped below those of the diesel fuel mixture for B25Us_irr
(after 100 seconds) and B50Us_irr (after 350 seconds) blends. Szybist et al. [69, 70] and
Bakeas et al. [4] show that higher bulk modulus causes advanced injection timing, one of the
reasons for increased NOx pollutant emissions.
From the point of view of the presented experiments, the decreasing tendency of the
isentropic bulk modulus for all the blends shows possibilities for reduced NOx emissions from
biodiesel-fuelled engines. The variation of isentropic bulk modulus has direct effect on
biodiesel’s ignition timing (that are more appropriate in conditions of ultrasonic irradiation to
diesel fuel one). Further, from this reason, the peak combustion temperature in the NOx
formation interval is decrease, because the premixed combustion intensity is reduced [78].
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 50
!
!
Figure 21. NOx emissions for the B25 blend (ultrasonic irradiated
and basic biodiesel)
Figure 23. NOx emissions for the B75 blend (ultrasonic irradiated
and basic biodiesel)
!
Habilitation thesis – F. Mariasiu 51
!
!
!
Figure 22. NOx emissions for the B50 blend (ultrasonic irradiated
and basic biodiesel)
Figure 24. NOx emissions for the B100 blend (ultrasonic irradiated
and basic biodiesel)
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 52
!
!
Only B25Us_irr blend’s kinematic viscosity shows lower values than those of diesel
fuel in the process of ultrasonic irradiation (after 350 seconds). The difference between the
kinematic viscosity of the B25Us_irr blend subjected to the full irradiation time of 600
seconds and that of the diesel fuel after 600 seconds was –28.25 % (Figure 20). Ultrasonic
irradiation was also beneficial for the other considered blends (B50, B75 and B100):
kinematic viscosity was reduced by an average of –19.74 %. Viscosity is considered a more
important biodiesel parameter that density, owing to its direct influence on the operation of
fuel injection engines’ equipment [40]. Szybist et al. [69] highlight the beneficial effect of a
fuel with lower viscosity on injection process parameters. Furthermore, the effect is related to
reduced NOx emissions.
The results obtained in experiments to test the fuelling of a DI diesel engine with
ultrasonically irradiated biodiesel confirm the interpretation of previous assumptions about
biodiesels’ physical parameter changes under the effects of ultrasonic irradiation. The
generally decreasing tendency of the treated biodiesels’ density, viscosity and isentropic bulk
modulus brings beneficial effects to the injection and combustion processes, with a direct
influence on NOx pollutant emissions formation.
According to the results presented in Figures 21-24, there are reductions in NOx
pollutant emissions for all regimes of the engine. The maximum value obtained is –18.2%
(for B25Us_irr, no engine load case) and the minimum is –1.4% (for B100Us_irr, 100%
engine load case), compared with emissions from untreated basic biodiesel. Using the
ultrasonically irradiated biodiesel, reductions in NOx emissions of greater than 10% were
obtained for low and medium load engine regimes. For B25Us_irr these load regimes are 0%
and 75% (–18.2% and –11.9%); for B50Us_irr they are between 0% and 50% (–14.3% and –
11.1%); and for B75Us_irr, they are for 0% engine load regime only, (–10.7%).
To can judge about the real effect of ultrasonic biodiesel blends treatment on NOx
pollutant emission, were analysed also the engine’s specific fuel consumption (BSFC) and
the brake power variations. The results are presented in Figures 25 and 26, considering the
relative variation of measurements before and after ultrasonic conditioning of biodiesel
blends.
Habilitation thesis – F. Mariasiu 53
!
!
Figure 25. Differences in BSFC for non-irradiated and irradiated biodiesel blends
Figure 26. Differences of engine’s brake power for non-irradiated and irradiated biodiesel blends
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 54
!
!
From above presented results it can said that the effect of ultrasonic irradiation
conduct to a generally (but smaller as values) decreasing tendency of BSFC. The major
reduction in BSFC was achieve for the B100Us_irr blend equal to -2.95% (at 0% engine
load). In the case of effective brake power a increasing tendency was measured with major
influence on B75Us_irr and B100Us_irr blends (+4.28% at 0% engine load, respectively
+4.43% at 75% engine load).
Based on the presented results, it can say that the reduction of NOx pollutant
emission is major caused by the effect of ultrasonic biodiesel blends conditioning on the
isentropic bulk modulus parameters change. The decreasing in BSFC correlated with a small
increasing of engine’s effective power, are the immediate effect of a more appropriate
ignition timing (that are influenced by the value of isentropic bulk modulus) of ultrasonic
biodiesel conditioned, to that of diesel fuel.
However, the NOx pollutant emission values, using the ultrasonic irradiated biodiesel
to fuel a DI diesel engine, remain higher than that using diesel fuel.
As a major conclusion, the ultrasonic irradiation process leads to important variations
in the physical parameters of biodiesels. In terms of density and viscosity (important
parameters for the injection process) the obtained results show equal values for the B25
blend and diesel fuel for an ultrasonic irradiation period of 420 seconds and 350 seconds
respectively. The variations of ultrasonically irradiated biodiesel physical characteristics show
potential in NOx pollutant emission reduction: potential confirmed through experimental
bench research on the performance of a direct injection diesel engine.
The major reduction in NOx pollutant emissions was observed for the B25Us_irr
blend conditioned by ultrasonic irradiation (–18.2% for no engine load to –8% for 100%
engine load) when compared to basic untreated biodiesel. However, there were still NOx
emissions values greater than those measured from the diesel fuel and the biodiesel’s
conditioning process by ultrasonic irradiation worse storage properties for long periods (by
increasing oxidative products in blends).
Through the ultrasonic irradiation process it is feasible to incorporate biodiesel fuels
into blends (with diesel fuel) for use in compression ignition engines without having to make
major or important changes and adjustments to the fuel injection systems of these engines.
Habilitation thesis – F. Mariasiu 55
!
!
4.2.3. Possibilities to improve cold-start process of engines fuelled with biofuels3
It is well known and establishes that diesel engines’ easy start depends directly on fuel
self-ignition quality and indirectly on fuel’s cetane index, viscosity, fuel freezing point and
cloud point temperature [7, 40]. In terms of behavior at low temperatures due to high
amounts of vegetable oils cloud point temperature is from +12°C to +30°C, compared to
diesel (-22°C to + 0°C); some problems will appear related to flow through the injection pump
(loss of engine power), clogging filters and supply lines [13]. Based on these considerations
we can say that physical and chemical properties of biodiesels have an important role on
technical considerations related to their use in compression ignition engines [40, 41].
Given that currently there is mainly machinery and vehicles that are equipped with
engines built with older technology than that used in 2000, in order to increase reliability as
well as fuel engines to use vegetable oil (pure or mixed form) technical changes must [13,
14]: ensure the possibility of using alternative fuels in compression ignition engines in any
season calendar and the superior performance in terms of lower pollution than petroleum
based fuels; not involve important changes in engine design (overall piston chamber,
cylinder, cylinder head etc.), in order not to increase significantly the cost price; not affect the
strength and thermal characteristics of engine mechanism parts; increase the reliability of
compression ignition engines that work with such fuels.
On the basis of previously presented, it is considered that the minimum necessary
technical changes to be made on components and/or installation of the engine especially
when used as biodiesel or pure vegetable oil based on the percentage of biodiesel from
vegetable oil mixture biodiesel (diesel + vegetable oil) are more than 70%, to facilitate their
use in low ambient temperature conditions [75]. Currently, the following technical changes
are recommended:
• Heating the biodiesel inside the tank (with heat exchanger Figure 27 or
electrical resistance Figure 28) [13];
• Biodiesel heating with heat exchanger mounted on the supply route (after the
tank), constructive solutions are proposed as those presented in Figure 29
[13, 14].
• Mixed supply systems, starting systems that allows diesel fuel initial start,
operating with biodiesel and again using diesel fuel to stop [13]. The fuels
switch used to equip such a mixed power system is shown in Figure 30.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!8!#$%&! '()$*! +,-! .(/0()012! 342! U(/@(2! E4! 567"79! I+))0'0=0&0$)! &+! 0;R/+?$! &C$! <+=*! )&(/&! R/+<$))! +B! &/(<&+/)! $,@0,$)! B1$==$*! V0&C!'0+*0$)$=2!W+1/,(=!+B!3++*2!Q@/0<1=&1/$!(,*!D,?0/+,;$,&!O58XP9-!""67N""662!67"74!!
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 56
!
!
The proposed method use to improving the cold start process of biofuel use for IC
(diesel) engines fueling and is based on an ultrasound system (Figure 31) that consists of a
PZT ultrasound emitter (35W), an electronic system that generates the ultrasounds and a
fuel filter (Mopar type 7-41354). Achieving thermal effect induced in biodiesel is possible due
to the interaction of ultrasound with its molecular structure. With this the biodiesel energy
levels increase and so does the activation degree of molecules, which increases the intensity
of clashes between them. The result of these clashes is the energy dissipation as friction
process result (in the process of collision) as the heat in the volume of biodiesel.
Energy consumed for the biodiesel heat through ultrasound is 3-5 times smaller than
existing solutions in the cases presented above. Also, the decoupling of device is automatic
when reaching the desired temperature by using a thermal sensor (Figure 31). The ultrasonic
emitter device is positioned in the manner most advantageous to the bottom battery fuel
filter.
The measuring devices consist of an IR Testo 850 thermometer and an IR thermal
camera Wuhan Guide IR type, and were used to achieve the necessary data about the
ultrasounds thermal transfer process on biodiesel. The biodiesel was rapeseed pure
vegetable oil and the experiments start at -15°C (alleged as base temperature for
experiment).
Figure 27. The biodiesel heating process with heat exchanger
mounted inside of fuel tank (1-fuel tank; 2-biodiesel; 3- heat
exchanger; 4-from cooling circuit; 5-to cooling circuit).
Habilitation thesis – F. Mariasiu 57
!
!
Figure 28. The biodiesel heating process with electric resistor device
mounted inside of fuel tank (1-fuel tank; 2-biodiesel; 3-electric
resistor).
!
Figure 29. The biodiesel heating process with heat exchanger mounted on fuels supply circuit
(1-power supply connecting wires; 2- biodiesel in; 3- biodiesel out; 4-electrical heater).
Figure 30. Fuel switcher [13](1-biodiesel in; 2- to injection pump; 3-diesel fuel in; 4-diesel fuel
out; 5-injection pump retour; 6-electromagnetic command system; 7- power supply connecting
wires).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 58
!
!
Figure 31. The cold start ultrasound system (1-biofuel out; 2-filter element; 3-filter case; 4-PZT
ultrasounds emitter; 5-thermal sensor; 6- biofuel in; 7-ultrasounds; 8- ultrasounds generator; 9-
electronic control unit; 10-12Vcc power supply system)
The experiments carried out by ultrasonic conditioning of biodiesel are seen as a
thermal effect occurs due to increased fuel and energy potential of increasing frequency of
collision with friction between fuel molecules. The results of experiment (the fuel filter thermal
finger-print and the temperature distribution along the filter case height) are presented in
Figures 32 to 34.
Figure 32. The temperature distribution on fuel filter longitudinal plane (10 s).
Habilitation thesis – F. Mariasiu 59
!
!
Figure 33. The temperature distribution on fuel filter longitudinal plane (20 s).
Figure 34. The temperature distribution on fuel filter longitudinal plane (30 s).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 60
!
!
After 10 s of biodiesel ultrasonic conditioning the thermal heating process increases the
temperature from -15 to -9°C but the heating is limited only to the base of fuel filter. After 20 s
of biodiesel ultrasonic conditioning the heating effect is present in almost half of the fuel filter
volume, the maximum temperature of biodiesel increase is -2.5°C from initial value of -15°C.
After 30 s of biodiesel ultrasonic conditioning the heated volume grows at the filter base
is to obtain a positive temperature of +5.5°C and also is obtained a higher average
temperature of biodiesel volume content in the filter (which leads to improve the engine cold
start process).
Considering the physical properties of biodiesel we can say that at least 20 s is
necessary for biodiesel ultrasonic conditioning to realize the necessary conditions for a
proper cold start process of a compression ignition engine fuelled with biodiesel [14, 75].
As a major conclusion, the cold start process of internal combustion engines fuelled
with biodiesel eliminates the presented disadvantages (of other systems) by being fitted with
an ultrasound-producing system, having reduced weight and being easy to assemble all
forms of fuel filter battery construction that are currently existing in the construction of internal
combustion engines fuel supply systems.
By applying the cold start system into the construction of a diesel engines fueling
system obtains the following advantages: simple and reliable construction due to lack of
moving mechanical elements; effect of heat transfer instantly to biodiesel; automating of
diesel engines cold start process; weight and reduced dimensions; ease of installation and
operation. Energy consumed for the actual heat through ultrasound is 3-5 times smaller than
existing solutions in the cases presented. Also, the decoupling device is automatic when
reaching the desired temperature. Another important advantage is the increasing of the
engine’s battery life with direct impact on environment protection and economical profit from
engine exploitation.
The device is positioned in the manner most advantageous to the bottom ultrasonic
emitter battery fuel filter. Location at the fuel filter bottom offers the innovative advantages:
quick release hole in the filter output of biodiesel by engine; already heated biodiesel will
further upward movement leading to the thermal effect of ultrasound near the amount of fuel
and contribute to melting paraffin deposits and agglomerations of the filter elements.
Habilitation thesis – F. Mariasiu 61
!
!
4.2.4. Possibilities to reduce engine’s friction losses at cold-start4
An original direction of research was the study of possibilities for reducing engine
friction losses at cold start using an ultrasonic irradiation technique. This unconventional
approach use an ultrasound emitter device (that manages minimum energy consumption
from engine’s battery) in order to modify the rheological properties of engine oil lubrication
and reduce friction losses. The results of laboratory experiments were processed in a
computer simulation of the diesel engine tractor cold start process. Losses due to internal
friction among engine components were comparatively analysed, and a lower percentage of
friction loss was obtained through ultrasonic conditioning of lubricating oil. The proposed
method offers benefits in terms of rational use and can prolong engine life with positive
effects on the economic efficiency of agricultural processes.
Desantes et al. [15] explained that the diesel engines offer advantages including ease
of operation, simple construction and reduced costs, relatively high thermal efficiency, and
good operational performance [i.e. power, torque, and brake specific fuel consumption
(BSFC)]. However, one of the great disadvantages of the diesel engine is that it can be
difficult to start at low ambient temperatures [12, 38]. The difficulty of cold start is due to the
mass of the cylinder block. In addition, the cylinder head absorbs the heat generated by the
compression stroke, which prevents the self-ignition of the fuel mixture (due to the higher
surface-to-volume ratio). This disadvantage is corrected by: using a glow plug to generate
heat inside the combustion chamber, having a higher compression ratio (19:1 to 23:1), or
modifying the fuel injection pattern [38].
A low temperature environment also affects the diesel engine lubrication processes.
Because the temperature directly affects lube oil viscosity, diesel engine start-up lubrication
is one of the most critical moments for lubrication. When lube oil has too high a viscosity at
cold start there is a risk of damage to the diesel engine including broken piston rings,
plugged filters, and oil pump failure. This is because, at engine start, all of the oil is in the
sump and the oil pressure is zero. The pump cannot begin to deliver the requested quantity
of oil until it sucks cold oil through the filter and delivers it to the engine lubrication system.
As the oil circulates and warms up (through contact with hot engine parts), the flow
increases, and the oil pressure drops to a stable level.
However, after this initial period of time (50 cycles at least) — to eliminate the effects
of transitory regime [21] — the engine and the engine components begin to receive proper
lubrication. Although cold start lubricating conditions are not critical for the crankshaft
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!P!#$%&! '()$*! +;-! .(/0()012! 34! 567"89! I+))0'0=0&0$)! B+/! /$*1<0,@! &/(<&+/! $,@0,$! B/0<&0+,! =+))$)! (&! <+=*! )&(/&! 1)0,@! (,! 1=&/()+,0<!0//(*0(&0+,!&$<C,0Y1$J2!#1/Z4!W4!Q@/0<4!3+/4!8[-!M68NM8"4!
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 62
!
!
bearings, other engine components such as the camshaft, lifters, connecting rod bearing,
piston pin, piston, piston rings, and cylinder walls are not fully lubricated in the time it takes
for the oil pump to pressurize the lubrication system and supply the necessary oil to the
engine [36]. The common solution for this problem is the use of engine lubricants with
additive technology (in combination with higher quality base stocks) that assure the
necessary oil viscosity for all temperature start conditions [8, 19, 35]. This can help to
maintain adequate engine wear protection during extended operation and under the more
severe conditions of an engine cold start-up process, as Plomer and Benda [55] and
Katafuchi and Masai [28] have shown. The disadvantages of this solution lie in the higher
costs and pollution concerns.
The present paper studies the possibility of developing electronic devices based on
ultrasonic wave emissions to decrease lubricating oil viscosity at cold start. Experimental
results were modelled through computer simulation using CRUISE software [2], which
facilitates calculation of engine friction losses at cold start-up.
The current study explored ultrasound (as external energy application) to change oil
lubrication rheological properties of the oil that lubes the engine mechanisms and
subassemblies. This work derives from experiments conducted by Mariasiu and Varga [39]
on the influence of ultrasonic processes on the physical characteristics of biodiesel blends.
The influence of ultrasound on lube oil parameters relating to internal combustion
engine lubrication (viscosity, density) was tested using an experimental device. An
ultrasound emitter of 35 Hz and 30 W (Bandelin Electronic GmbH, Berlin, Germany) was
mounted in the engine crankcase oil (Figure 35). Under initial experimental conditions the
ultrasonic energy density was 5220.7 kJ L–1. The initial temperature of the crankcase
lubricating oil was –10 °C (measured by placing crankcase and oil in a cold room with climate
control), and the ultrasonic effect on the lubricating oil was considered in effect until the oil
temperature (in the vicinity of the oil sump position) reached 10 °C.
Measurement of variation in lubricating oil viscosity (dynamic and kinematic) was
performed with the Anton Paar SVM 3000 Stabinger Viscometer (Anton Paar GmbH, Graz,
Austria). Video captures of the thermal footprint of ultrasound effects on lubricating oil were
taken by thermal-acquisition video camera (Wuhan Infrared TP8 type; Guide Infrared Co.,
Wuhan, China). The lubricating oil used in the experiment was a mineral type (20W50)
produced and sold by SC MOL SRL in Romania (Table 8).
The experiments described above were carried out in order to represent the effect of
ultrasound on the physical parameters of the lubricating oil (viscosity). Ultrasonic energy
transferred into a volume of lubricating oil causes vibration and friction between molecules in
Habilitation thesis – F. Mariasiu 63
!
!
the lubricating oil. Collisions and high-frequency repeated friction causes a heating effect that
directly influences the physical parameters of lubricating oil.
The thermal effect of ultrasound in a volume of lubricating oil (under our experimental
conditions) was highlighted by video acquisition of oil volume thermal fingerprints for different
time periods. A determination of lube oil viscosity variation and values, depending on the
effects of ultrasound, was acquired as an input parameter for the computer simulation model.
Table 8. MOL 20W50 engine oil: typical properties.
Properties Value Standards
Density at 15 °C [g cm–3] 0.891 ASTM D1250
Kinematic viscosity
at 40 °C [mm2 s–1]
161.0 ASTM D445
Kinematic viscosity
at 100 °C [mm2 s–1]
17.9 ASTM D445
Viscosity index [ - ] 120 ASTM D341
Pour point [°C] –27 ASTM D97
Flash point [°C] 240 ASTM D92
Base number BN [mg KOH g–1] 5.1 ASTM D2896
Computer simulation is one of the contemporary methods used by researchers to
solve technical problems [66]. Recently, development of mathematical models has allowed
for better correspondence between the physical models and numerical models, and this has
led to the use of computer simulation of specific processes of tractors and agricultural
machinery. In order to determine the friction losses due to engine cold start-up, we used a
simulation software package (CRUISE, AVL GmbH [2]).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 64
!
!
Figure 35. Ultrasonic transmitter location in the oil crankcase (1 - electrical connections, 2 - ultrasonic
emitter, 3 - oil pump sump, 4 - transfer pipe, 5 - oil crankcase).
The CRUISE computer simulation package is used through an interface that allows
for total or partial construction of components, subassemblies, and assembly models that
constitute a vehicle and its operating parameters and conditions. The CRUISE friction model
had the advantage of allowing for engine design variables such bore, stroke, and number of
valves in addition to operating conditions (engine speed, load, and oil temperature).
The values of friction loss coefficients were calculated, considering relevant engine
design and operating condition variables. Using the SLM (Shayler, Leong, and Murphy)
model proposed and developed by Shayler et al. [62, 63], we calculated the effect of ambient
temperature on the functional parameters and emissions of internal combustion engines
(spark ignition or compression ignition) to determine friction losses in the motor mechanisms.
The Shayler, Leong, and Murphy [64] model fits friction teardown data from motored engine
tests on 4-cylinder diesel engines.
The original purpose of the experimental work was to examine friction losses at low
temperatures and low engine speeds in connection with studies of cold start behaviour. The
SLM model generates an estimate for friction mean effective power (FMEP), which is then
subtracted from the engine-indicated mean effective pressure (IMEP) to obtain brake mean
effective pressure (BMEP).
Habilitation thesis – F. Mariasiu 65
!
!
The magnitude of friction processes is determined empirically from engine layout and
characteristics and is a function of engine speed, oil viscosity, and ambient temperature [62,
63].
As seen in Equations (12–15), the SLM model takes into account the important
parameter of lubrication process quality (oil viscosity), a physical parameter that varies in the
case of ultrasonic conditioning.
The crankshaft friction mean effective pressure is:
!"#$!"#$%&!!"# ! !!!!!!!!!!
!!" ! !!!! ! !!! ! !! ! !!!
!!"#
!! !!" (12)
, considering the oil lubrication viscosity index n = 0.24; N – engine rotational speed [min–1]; µ
– oil dynamic viscosity [Pa s]; µref – oil dynamic viscosity at 40 °C [Pa s].
The friction mean effective pressure in the piston group is:
!"#$!"#$%& ! !!!"#
!!!" ! !
!!!!!!!!!!!!!!
! !!!!!!!
!!" ! !!" !!!
(13)
where the oil lubrication viscosity index is n = 0.4, and Vp = 15.17 m s–1 is piston average
speed.
The friction mean effective pressure in the valve train is calculated using Eq. (14):
!"#$!"#!$%&"'(
! !!!"#
!!!"
!!!! ! !!!!! ! ! ! !!
! !!!!!!!! ! !!!! ! !!!! ! ! ! !!
! !!"
! !!" ! ! !"! ! !"
!! ! !!! ! !!
!!"#$!"#
!"#$!"# ! !!" ! ! !"!!!!!
!!!!!!
(14)
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 66
!
!
, where the oil lubrication viscosity index is n = 0.7, and Lv = 0.0085 is maximum valve lift [m].
The auxiliary losses (for oil and water pump) can be calculated using Eq. (15):
!"#$!"# ! ! ! !" ! !!! !!!"#
! (15)
The values for the constants (%, &, ') and the viscosity index (n) are, respectively:
1.28 kPa, 7.9 · 10–3 kPa mm3 min, –8.4 · 10–7 kPa mm3 min2, and 0.3 for the oil pump; for the
water pump: 0.13 kPa, 2 · 10–3 kPa mm3 min, 3 · 10–7 kPa mm3 min2, and 0.7 [11].
Considering the design particularities of the engine; the experimental results of
Shayler et al. [64], and Patton et al. [53], and the theory of lubrication [76], the values and
relationships of the friction model coefficients are presented in Table 9 (N was estimated at
700 min–1). The relationships used to calculate the SLM friction model coefficients presented
in Table 9 couldn’t be used for other engine models; however, they can be used for further
research and simulations regarding the influence of different oil viscosities on friction losses
for the diesel engines considered.
The simulation model was based on the D-110 diesel engines (direct injection, 4 in-
line cylinders, water cooling system) that equip Romanian U650 agricultural 2 WD tractors.
The structure of U650 CRUISE simulation model is presented in Figure 36 and the
Simulink friction model structure in Figure 37.
The engine general technical characteristics considered as input parameters in the
computer simulation are presented in Table 10. Additional data required are lubricating oil
viscosity function of environmental temperature. The model is also used to determine
functional and dynamic tractor performance for specific agricultural work.
In terms of lubricating oil ultrasound conditioning, related experimental data obtained
from viscosity variation are shown in Figure 38. Note that baseline for kinematic viscosity
considered at –10 °C decreases by 26.1%, 44.8%, 58.4%, and 68.3% after 63.2, 125, 221.2,
and 261.1 s, of ultrasonic process, respectively. The values shown above were measured for
lubricating oil temperatures of –5 °C, 0 °C, and 5 °C; the maximum temperature (10 °C)
considered during the experiment was obtained after 261.1 s.
Habilitation thesis – F. Mariasiu 67
!
!
Table 9. Calculation relationships of SLM friction model coefficients.
Coefficient Value/Relation
Ccb 4.16 · 10-3
Ccs 1.22 · 105
Cpb 0.576
Cps 11.45
Cpr 1.58 · 103
Cvb 6.118
Cvf 600
Cvh 600
Cvm !"!!" ! !! ! !"" ! !
Cvs 1458
Figure 36. CRUISE simulation model structure.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 68
!
!
Figure 37. Simulink friction model structure.
Heat inducted in the lubricating oil volume as a direct effect of ultrasonic irradiation
processes, and measured as oil temperature, is presented in Figure 39. The measured
temperature variation in the oil volume slope is 5.33 °C min–1; it’s relative linear tendency
was also confirmed by Lee et al. [34].
Habilitation thesis – F. Mariasiu 69
!
!
Table 10. Engine’s functional and constructive characteristics (model input data).
Parameter Value Parameter Value
Engine type Diesel Compression ratio 17:1
Displacement 4750 cm3
Engine nominal
temperature 80 °C
Bore 108 mm
Crankshaft main
bearing diameter 85.2 mm
Stroke 130 mm
Crankshaft main
bearing length 34.5 mm
Power
(at 1800 min–1)
47.8 kW
Big end con rod
bearing diameter 79.0 mm
Torque
(at 1250 min–1) 289 N m
Big end con rod
bearing
length
33.2 mm
Type of cam follower Flat follower
Type of valve
train OHV
Number of crankshaft main bearings 5
Number of intake valves
per cylinder 1
Number of camshaft bearings 6
Number of exhaust valves
per cylinder 1
Engine oil SAE 20W50 Maximum valve lift 8.5 mm
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 70
!
!
Figure 38. Effect of ultrasonic irradiation on lubricating oil’s viscosity and temperature.
Thermal prints provide a picture of the ultrasound thermal propagation effect in the
lubricating oil for the time considered (300 s). Lubricating oil’s temperature, as a direct effect
of ultrasound irradiation, was 12.1 °C (Figure 39).
Results obtained from the computer simulation (Figures 40 and 41) presented the
differences in friction loss among different engine mechanisms during cold start-up. Detailed
results for each engine component considered (crankshaft and main bearings, piston group,
valve train, and auxiliaries) are presented in Table 11. Among the components and engine
systems considered in the simulation (Table 11) the highest friction loss values were found in
the piston group (3.269 kW) and auxiliaries (3.172 kW). This justifies specialized design and
construction of these components in order to assure minimal effects of wear. Under cold start
conditions the valve train system supports high intensity wear, as presented above.
Variations of +1.62% in friction loss for cam and cam followers and +1.62% in mixed
oscillating valve train lubrication were obtained. These slight increases in friction loss may be
due to oil viscosity reduction. If the viscosity is reduced below the level required for
hydrodynamic support, the cam surface will contact the cam follower surface, creating
boundary contact friction. In total, a major (– 40.94%) reduction in friction loss was achieved
for the valve train system after 261 s of ultrasonic irradiation of the lubricating oil for an
engine cold start at –10 °C.
Habilitation thesis – F. Mariasiu 71
!
!
Figure 39. Thermal prints of ultrasound effects (starting from –10 °C lubricating oil temperature).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 72
!
!
Figure 40. Total friction losses for examined cold start conditions.
!
Figure 41. Friction loss distribution for valve train assembly.
!!!!
Habilitation thesis – F. Mariasiu 73
!
!
Table 11. Comparative friction loss magnitude for different engine components.
Ultr
ason
ic ir
radi
atio
n be
fore
en
gine
igni
tion
(s)
Oil
tem
pera
ture
[°C
]
Friction losses [kW]
Cra
nksh
aft a
nd m
ain
bear
ing
Pis
ton
grou
p
Val
ve tr
ain
Aux
iliar
ies
Tota
l
0.00 -10 1.39 3.27 0.964 3.17 8.80
63.2 -5 1.07 2.68 0.776 2.17 6.70
125.0 0 0.85 2.25 0.670 1.57 5.35
221.2 5 0.70 1.92 0.60 1.19 4.43
261.1 10 0.58 1.67 0.57 0.95 3.77
The aim of this study was to present the possibility of reducing engine friction losses
at cold start by using an experimental device to ultrasonically irradiate lubricating oil. The
experiments determined variation in oil viscosity due to the thermal effect induced by
ultrasound. Furthermore, viscosities of lubricating oil at – 10 °C, –5 °C, 0 °C, 5 °C, and 10 °C
were set as input parameters for the D-110 engine cold start computer simulation.
Analysing the simulation data we found that engine friction losses decrease with
increasing ambient temperature, as expected. With positive lubricating oil temperatures there
is a more rapid lubrication of engine components. Assuming the maximum power tractor
engine D-110 is 47.8 kW, friction loss at cold start (–10 °C) is 18.41% of total engine power
(Figure 40).
The greatest variations in friction loss reduction through the ultrasonic effect on
lubricating oil were obtained for camshaft bearing hydrodynamics (–74.17%) and oscillating
valve train friction losses by hydrodynamic lubrication (–79.04%). In other areas of friction
loss there were no reductions achieved; however, these areas are important as a share in
the total value of engines friction losses (Figure 41).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 74
!
!
The immediate effect of the results presented above is a major increase in engine
component reliability, as well as growth in motor engine functional performance (power,
torque, and BSFC), with a direct influence on lowering pollutant emissions. Another important
advantage of using an ultrasonic device that can improve lubricating oil parameters is lower
energy consumption and a reduction in accumulator battery strain, when compared to an
electrical resistor oil heating system. In addition, the use of electrical resistors to heat the
lubricating oil leads to the rapid thermal degradation of the oil. This degradation produces
additional costs related to increased maintenance (i.e. default costs of purchasing new oil,
human labour costs, and replacement parts).
Reducing friction losses increases the lifespan of the engine with immediate benefits
in maintenance and operational costs: a mandatory process requirement. The practical
application of the device presented involves an economic cost of approximately /83
(hardware and human labour costs); this represents less than 0.3% of the purchase cost of a
new engine.
Habilitation thesis – F. Mariasiu 75
!
!
5. CONCLUSIONS
The research activity of candidate was constant in idea to offer applicative solutions in
order improve internal combustion engines’ performance (to make the connection between
fundamental and applicative research). Both, conventional and unconventional methods and
approaches were used, and results of researches were disseminated at different levels using
different channels, to increase the public awareness about the contemporary problem of
environment pollution and subsequently, to improve IC engine performance.
There are also highlighted future directions of research, derived from actual work:
• Exploring the connecting possibilities of biodiesel injection process’
influences with new solutions in piston bowl designing, injection strategy,
and initial bowl swirl ratio to optimize the efficiency of the biodiesel
combustion process.
• Researches of the ultrasonic irradiation process on different types of
methyl esters (soy, palm oil, sun flower, etc.) and with different values of
transmitted ultrasonic density in fuel (taking into consideration the use of
low-power and also low-cost ultrasonic horns).
• Using different ultrasound emission frequencies should do future research.
In addition, the energy density of the ultrasound in relation to volume and
crankcase oil constructive shape and the optimal location and number of
ultrasonic emitters, depending on the construction of the lubrication
system, should be determined.
• New approaches regarding the creation and use of tertiary mixtures
(bioethanol + vegetable oil methyl ester + diesel fuel) to fuelling internal
combustion engines (compression ignition engines), by a novel and
innovative fumigation method using ultrasounds (Figure 42).
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 76
!
!
• To reduce the influence and magnitude level of engine’s friction losses, as
a major impact factor on engine’s overall energetic efficiency.
Improvement of engine’s mechanisms and systems tribology lead to
increase of mechanic efficiency and consequently to less consumed fuel
and less amount of pollutant emission.
• Investigation of possibilities to use benign (environmental friendly) nano-
materials in green bio-lubricants.
Figure 42. Innovative fumigation method for fuels based on tertiary mixtures
(1-ultrasound emitter, 2-fan, 3-air stream, 4-bioethanol, 5-intake pipe,
6-intake air, 7-vaporized bioethanol, 8- injector, 9-exhaust pipe).
Habilitation thesis – F. Mariasiu 77
!
!
6. CAREER DEVELOPMENT PLAN
The candidate’s career development plan will be sustained by continuous activity and
training (preparation) in both research and educational domains.
In actual context, at worldwide level, of necessity to improve energetic efficiency of
internal combustion engines (by direct actions and/or introducing of new technologies) there
are continue demands in development of application of new materials and technology. Based
on this issue the same original and unconventional approaches in candidate’s research
activity will be following.
The candidate’s research and educational activities will be oriented in future, in major
goal achievement of active contribution on above presented issue.
The short-term career objectives are follows:
o Obtaining the title of professor
o Publication of scientific articles (to disseminate the research results) in
important journals
o Application of blended and e-learning principles and also the use of
TIC instruments in students education
o Transfer to young researchers the accumulated know-how in project
management
o Continue developing of proposals for national and international
research calls (coordinator/member)
o Developing the international collaboration (institutional and research)
o Collaboration with industry stakeholders on both educational and
research levels.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 78
!
!
The long-term career objectives are follows:
o Enrolments (tutoring) of 1-2 PhD students per year
o Continue activity in national/international research calls participation
o Development of international contacts (institutional and research)
o Participating to international conferences to disseminate the research
results
o Increasing the national and international visibility of Automotive
Engineering and Transports Department
o Increasing the attractively of research activity for young researchers
o Continue transfer of accumulated knowledge to students and PhD
students
o Development of new line of study (bachelor and/or master) in advance
technologies for modelling and simulation in automotive engineering
o Continue dissemination of research activity (workshops, scientific
articles, textbooks) at national and international levels
o Extending the collaboration with industry stakeholders on both
educational and research levels
Habilitation thesis – F. Mariasiu 79
!
!
References
[1] AVL Advance Simulation Technologies. (2009), AVL FIRE, AVL Advance
Simulation Technologies: Graz, Austria.
[2] AVL CRUISE v. 2009 User Manual. AVL LIST GmbH: Graz, Austria.
[3] Badock, C., Wirth, R., Fath, A., and Leipertz, A. (1999) Investigation of Cavitation
in Real Size Diesel Injection Nozzles, International Journal of Heat and Fluid Flow,
20: 538–544.
[4] Bakeas, E., Karavalakis, G., Stournas, S. (2011) Biodiesel emissions profile in
modern diesel vehicles. Part 1: Effect of biodiesel origin on the criteria emissions,
Sci. Total Environ 409: 1670-1676.
[5] Bari, S., Liu, T.H., Yu, C.W. (2002) Effects of preheating of crude palm oil (CPO)
on injection system, performance and emission of a diesel engine, Renewable
Energy 27: 339-351.
[6] Berchiche, N., Franc, J. P., and Michel, J. M. (2002) Cavitation Erosion Model for
Ductile Materials, Journal of Fluids Engineering, 124: 601–606.
[7] Bessee, G. B. et al. (1997) Biodiesel Fuel Technology for Military Application.
Southwest Research Institute, Interim Report TFLRP No. 317.
[8] Becker EP (2004) Trends in tribological materials and engine technology. Tribol
Int 37: 569–575.
[9] Blessing, M., Konig, G., Kruger, C., Michels, U., and Schwartz, V. (2003) Analysis
of Flow and Cavitation Phenomena in Diesel Injection Nozzles and Its Effects on
Spray and Mixture Formation, SAE International Technical Paper No. 2003-01-
1358.
[10] Boehman, A.L., Morris, D., Szybist, J.P., Esen, E. (2004) The impact of the bulk
modulus of diesel fuels on fuel injection timing, Energy Fuels 18: 1877-1882.
[11] Bohac SV, Baker DM, Assanis DN (1996) A global model for steady state and
transient S.I. engine heat transfer studies. SAE Paper No. 960073.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 80
!
!
[12] Brown N, Gupta V, La Rocca A, Shayler PJ, Murphy M, Pegg I, Watts M (2007)
Investigations of fuel injection strategy for cold starting d.i. diesel engines. Proc. I
Mech E, Part D: J Automotive Eng 221: 1415–1424.
[13] Burnete, N. et al. (2005) The Rapeseed - A Challenge for Farmers and
Energeticians. Sincron Publishing House, Cluj-Napoca, Romania.
[14] Burnete, N. et al. (2008) Diesel Engines and Biofuels for Urban Transportation.
Mediamira Publishing House, Cluj-Napoca, Romania.
[15] Desantes, J., Arregle, A., Pastor, J. V., and Delage, A. (1998) Influence of the
Fuel Characteristics on the Injection Process in a D.I. Diesel Engine, SAE
International Technical Paper No. 980802.
[16] Dziza, M., Prusakiewicz, P. (2008) The effect of temperature and pressure on the
physicochemical properties of petroleum diesel and biodiesel fuel oil, Fuel 87:
1941-1948.
[17] European Comission (2009) Directive 2009/28/EC of the European Parliament
and of the Council of 23 April 2009 on the promotion of the use of energy from
renewable sources, http : // eur – lex . Europa . eu / legal – content / RO/TXT /
PDF/?uri=CELEX:32009L0028&from=EN, accessed November 2014.
[18] Franc, J.P., Riondet, M. (2006) Incubation Time and Cavitation Erosion Rate of
Work-Hardening Materials, Sixth International Symposium on Cavitation
“CAV2006,” Wageningen, The Netherlands.
[19] Fox, I.E. (2005) Numerical evaluation of the potential for fuel economy
improvement due to boundary friction reduction within heavy-duty diesel engines.
Tribol Int 38: 265–275.
[20] Gavaises, M., Andriotis, A. (2006) Cavitation inside Multi-Hole Injectors for Large
Diesel Engines and Its Effects on the Near-Nozzle Spray Structure, SAE
International Technical Paper No. 2006-01-1114.
[21] Giakoumis, E.G. (2010) Lubricating oil effects on the transient performance of a
turbocharged diesel engine. Energy 35: 864–873.
[22] Giannadakis, E. (2005) Modelling of Cavitation in Automotive Fuel Injector
Nozzles, Doctoral Thesis, Imperial College, University of London.
[23] Giannadakis, E., Gavaises, M., Arcoumanis, C. (2008) Modelling of Cavitation in
Diesel Injector Nozzles, Journal of Fluids Mechanics, 616: 153–193.
[24] Gogate, P.R., Kabadi, A.M. (2009) A review of applications of cavitation in
biochemical engineering/biotechnology, Biochem. Eng. J. 44:60-72.
Habilitation thesis – F. Mariasiu 81
!
!
[25] Goodrum, J.W. (2002) Volatility and Boiling Points of Biodiesel from Vegetable
Oils and Tallow, Biomass and Bioenergy, 22: 205–211.
[26] He, L., Ruiz, F. (1995) Effect of Cavitation on Flow and Turbulence in Plain
Orifices for High-Speed Atomization, Atomization and Sprays, 5: 569–584.
[27] Kang, J., Lee, K., Koh, C., Nam, S. (2001) The kinetics of the sonochemical
process for the destruction of aliphatic and aromatic hydrocarbons, Korean J.
Chem. Eng. 18(3): 336-341.
[28] Katafuchi T, Kasai M (2009) Effect of base stocks on the automobile engine
bearing. Tribol Int 42: 548–553.
[29] Kegl, B., Kegl, M., Pehan, S. (2008) Optimization of a fuel injection system for
diesel and biodiesel usage, Energy Fuel 22: 1046-1054.
[30] Knothe, G. (2008) “Designer” biodiesel: Optimizing fatty ester composition to
improve fuel properties, Energy Fuels 22: 1358–1364.
[31] Labekas, G., Slavinskas, S. (2005) Performance and exhaust emissions of direct-
injection diesel engine operating on rapeseed oil and its blends with diesel fuel,
Transport 20(5): 186-194.
[32] Lebedevas, S., Vaicekauskas, A., Lebedeva, G. et al. (2006) Research into
operational parameters of diesel engine running on RME biodiesel, Transport
21(4): 260-268.
[33] Lebedevas, S., Vaicekauskas, A. (2006) Research into the application of biodiesel
in the transport sector of Lithuania, Transport 21(2): 80-87.
[34] Lee, S.B., Lee, J.D., Hong, I.K. (2011) Ultrasonic energy effect on vegetable oil
based biodiesel synthetic process, J. Ind. Eng. Chem. 17:138-143.
[35] Leong D.K.W., Shayler P.J., Pegg I.G., Murphy M. (2007) Characterizing the
effect of viscosity on friction in the piston assembly of internal combustion
engines. Proc Instn Mech Engrs, J Eng Tribol 221: 469–478.
[36] Livanos, G., Kyrtatos, N.P. (2006) A model of the friction losses in diesel engines.
SAE Paper No. 2006-01-0888.
[37] Liu, F., Wang, J., Chen, D., Xu, Y., and Zhao, M. (2010) The Cavitation Erosion of
the #45 Carbon Steels Implanted with Titanium and Nitrogen, Tribology
Transactions, 53(2): 239–243.
[38] MacMillan D, LaRocca A, Shayler PJ, Morris T, Murphy M, Pegg IG (2009) The
influence of multiple pilot injections on the quality of idling after cold start up of a
light duty diesel engine. SAE Paper No. 2009-01-0612.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 82
!
!
[39] Mariasiu, F., Varga, B. (2009) Simulation of the Combustion Chamber Geometric
Shape with the Liquid Length Phase Penetration of Biofuel Jet Spray, Proceedings
of “Actual Tasks on Agricultural Engineering,” Opatija, Croatia, February.
[40] Mariasiu, F., Burnete, N., Deac, T. (2009) Possibilities to Determinate the Biofuels
Physically Parameters in Functional Conditions, Research Journal of Agricultural
Science, 41(2): 451–456.
[41] Mariasiu, F. (2007) Technical modification of biodiesel fueled engines. Biodiesel
Magazin 3: 30-34.
[42] Mason, T.J., Lorimer, J.P. (1988) Sonochemistry: Theory, applications and use of
ultrasound in chemistry, John Wiley & Sons, New York.
[43] Mason, T.J., Lorimer, J.P. (2002) Applied Sonochemistry: The uses of power
ultrasound in chemistry and processing, Wiley-VCH Verlag GmbH, Weinheim.
[44] Marmottant, P., Villermaux, E. (2004) On Spray Formation, Journal of Fluids
Mechanics, 498: 73–111.
[45] Martynov, S. (2005) Numerical Simulation of the Cavitation Process in Diesel Fuel
Injectors, Doctoral Thesis, University of Brighton, Brighton,UK.
[46] Martynov, S., Mason, D., Heikal, M. (2005) Hydrodynamic Similarity of Cavitation
Flows in Nozzles, Proceedings of the 5th International Symposium “Multiphase
Flow, Heat and Mass Transfer and Energy Conversion,” Xian, China, July 3–6,
2005.
[47] Mazzoleni, C., Kuhns, H.D., Moosmüller, H., et al. (2007) A case study of real-
world tailpipe emissions for school buses using a 20% biodiesel blend, Sci. Total
Environ 385(1-3): 146-159.
[48] Nabi, M.N., Hustad, J.E. (2010) Experimental investigation of engine emissions
with marine gas oil-oxygenate blends, Sci. Total Environ 408(16): 3231-3239.
[49] Ngondi, E. M., Gronsfelder, T., Nordmann, R. (2010) Mesh Movement Method for
Transient Simulation of Annular Cavities: Application to Prediction of Fluid Forces
in Squeeze Film Dampers, Tribology Trans- actions, 53(3): 440–451.
[50] Nurick, W. H. (1976) Orifice Cavitation and Its Effect on Spray Mixing, Journal of
Fluids Engineering, 98: 681–687.
[51] Park, H.S., Yoon, S.H., Suh, H.K., Lee, C.S. (2008) Effect of temperature variation
on the properties of biodiesel and bioethanol and biodiesel fuels blends, Oil Gas
Sci. Technol. 63(6): 737-745.
[52] Park, S.H., Kim, H.J., Lee, C.S. (2009) Experimental and numerical analysis of
spray-atomization characteristics of biodiesel fuel in various fuel and ambient
Habilitation thesis – F. Mariasiu 83
!
!
temperature conditions, Int. J Heat Fluid Flow 30: 960-970.
[53] Patton, K.J., Nitschke, R.G., Heywood, J.B. (1989) Development and evaluation of
a friction model for spark ignition engines. SAE Paper No. 890836.
[54] Payri, R., Salvador, F.J., Gimeno, J., Bracho, G. (2011) The effect of temperature
and pressure on thermodynamic properties of diesel and biodiesel fuels, Fuel
90:1172-1180.
[55] Plomer, A., Benda, R. (2000) Modern heavy-duty diesel engine cold start wears
study. Ind Lubr Tribol 52: 277–285.
[56] Qu, J., Truhan, J.J., Blau, P.J., Ott, R. (2007) The Development of a ‘Pin-on-Twin’
Scuffing Test to Evaluate Materials for Heavy-Duty Diesel Fuel Injectors, Tribology
Transactions, 50(1): 50–57.
[57] Ramirez del Solar, M., de la Rosa-Fox, N., Esquivias, L., Zarzicky, J. (1990)
Kinetic study of gelation of solventless alkoxide-water mixtures, J. Non-Cryst.
Solids121: 40-44.
[58] Reitz, R. D. (1987) Modelling Atomization Process Processes in High-Pressure
Vaporizing Sprays, Atomization and Sprays, 3: 309– 337.
[59] Roosen, P., Unruh, O., Behmann, M. (1996) Untersuchung und Modeleirung des
Transienten Verhaltens von Kavitationserscheinungen bei ein- und
Mehrkomponentigen Kraftstoffen in Schnell Durchstromten Dusen, (Analysis and
modeling of cavitation transient behavior at one- and multi-component fuels in
quick traversed nozzles), Report of the Institute for Technical Thermodynamics,
Aachen, Germany.
[60] Sazhin, S., Crua, C., Kennaird, D., Heikal, M. (2003) The Initial Stage of Fuel
Spray Penetration, Fuel, 82: 875–885.
[61] Schmidt, D. P., Corradini, M. L. (2001) The Internal Flow of Diesel Fuel Injector
Nozzles: A Review,” International Journal of Engine Research, 2: 1–22.
[62] Shayler, P.J., Christian, S.J., Ma T. (1993) A model for the investigation of
temperature heat flow and friction characteristics during engine warm-up. SAE
Paper No. 931153.
[63] Shayler, P.J., Baylis, W.S., Murphy, M. (2005) Main bearing friction and thermal
interaction during the early seconds of cold engine operation. J Eng Gas Turbines
and Power 127: 197–205.
[64] Shayler, P.J., Leong, D.K.W., Murphy, M. (2005) Contributions to engine friction
during cold, low-speed running and the dependence on oil viscosity. SAE
Transactions: Journal of Engines 114: 1191–1201.
[65] Siebers, D. L. (1998) Liquid-Phase Fuel Penetration in Diesel Sprays, SAE
International Technical Paper No. 980809.
Researches on possibilities to improve biofuel’s use in internal combustion engines fuelling 84
!
!
[66] Silleli, H. (2007) Research on applying an anchor mechanism to orchard and
vineyard tractors produced in Turkey. Turk J Agric For 31: 389–398.
[67] Som, S., Longman, D. E., Ramirez, A. I., Aggarwal, S. K. (2010) Comparison of
Injector Flow and Spray Characteristics of Biodiesel with Petrodiesel,” Fuel, 89:
4014–4024.
[68] Stavarache, C., Vinatoru, M., Maeda, Y. (2006) Ultrasonic versus silent
methylation of vegetable oils, Ultrason Sonochem 13:401-407.
[69] Szybist, J.P., Boehman, A.L., Taylor, J.D., McCormick, R. (2005) Evaluation of
formulation strategies to eliminate the biodiesel NOx effect, Fuel Process.
Technol. 86: 1109-1126.
[70] Szybist, J.P., Song, J., Alam, M., Boehman, A.L. (2007) Biodiesel combustion
emissions and emission control, Fuel Process. Technol. 88: 679-691.
[71] Tamaki, N., Shimizu, M., Hiroyasu, H. (2001) Enhancement of the Atomization of
a Liquid Jet by Cavitation in a Nozzle Hole, Atomization and Sprays, 11: 125–137.
[72] Tat, M.E., Van Gerpen, J.H. (2000) Measurement of biodiesel speed of sound and
its impact on injection timing, Final Report for National Renewable Energy
Laboratory, subcontract no. ACG-8-18066-11.
[73] Tat, M.E., Van Gerpen, J.H. (2003) Speed of sound and isentropic bulk modulus
of biodiesel and diesel fuel mixtures, J. Am. Oil Chem. Soc. 80(11): 1127-1130.
[74] Torres-Jimenez, E., Dorado, M.P., Kegl, B. (2011) Experimental investigation on
injection characteristics of bioethanol-diesel fuel and bioethanol-biodiesel blends,
Fuel 90: 1968-1979.
[75] Tyson, S. K. (2001) Biodiesel Handling and Use Guidelines. National Renewable
Energy Laboratory Report No. TP-580-30004, 2001. www.biodiesel.com.
[76] Tudor, A., Prodan, Gh., Muntean, C., Motoiu, R. (1988) Durability and reliability of
mechanical transmissions (in Romanian), Editura Tehnica, Bucuresti, Romania.
[77] Vasanthi, R.S., Kinal, J.P., Gediminas, M. et al. (2009) Pulmonary effects of
inhaled diesel exhaust in aged mice, Toxicology and Applied Pharmacology
241:283-293.
[78] Wang, D., Zhang, C., Wang, Y. (2007) A Numerical Study of Multiple Fuel
Injection Strategies for NOx Reduction from DI Diesel Engines, Intern. J. Green
Energ. 4: 453-470.
[79] Wang, X., Huang, Z., Kuti, O. A., Zhang, W., Nishida, K. (2010) Experimental and
Analytical Study on Biodiesel and Diesel Spray Characteristics under Ultra-High
Injection Pressure, International Journal of Heat and Fluid Flow, 31: 659–666.
[80] Warren, K. H. Stephens, L. S. (2009) Effect of Shaft Microcavity Patterns for Flow
and Friction Control on Radial Lip Seal Performance—A Feasibility Study,
Habilitation thesis – F. Mariasiu 85
!
!
Tribology Transactions, 52(6): 731–743.
[81] Winklhofer, E., Kull, E., Kelze, E., and Morozov, A. (2001) Comprehensive
Hydraulic and Flow Field Documentation in Model Throttle Experiments under
Cavitations Conditions, Proceedings of ILASS-Europe, Zurich, Switzerland.
[82] Wu, P., Yang, Y., Colucci, J., Grulke E.A. (2007) Effect of ultrasonication on
droplet size in biodiesel mixtures, J. Am. Oil Chem. Soc. 10: 1746-1760.
[83] Yi, Y., Reitz, R. D. (2003) Modelling the Effect of Primary Atomization on Diesel
Engine Emissions, SAE International Technical Paper No. 2003-01-1041.
[84] Yuan, W., Hansen, A. C., Zhang, Q. (2005) Vapor Pressure and Normal Boiling
Point Predictions for Pure Methyl Esters and Biodiesel Fuels, Fuel, 84: 943–950.
[85] Zhang, J., Du, Q., Yang, Y. (2010) Influence of Diesel Nozzle Geometry on
Cavitation Using Eulerian Multi-Fluid Method, Transactions of Tianjin University,
16: 33–39.
[86] Zhu, L., Cheung, C.S., Zhang, W.G., Huang, Z. (2010) Emissions characteristics
of a diesel engine operating on biodiesel and biodiesel blended with ethanol and
methanol, Sci. Total Environ 408(4): 914-921.