HALO I VANITY UNITDOOR/S WITH INTERNAL FIXED SHELF - TOUCH RELEASE & CORIAN HANDLE OPTIONS
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
STANDARD SIZES 500 600 1000 1200 1500 1800
Width (mm) 500 600 1000 1200 1500 1800
Depth (mm) 450 450 450 450 450 450
Height (mm) 450 450 450 450 450 450
Number of Doors 1 2 2 2 4 4
Basin Options 1 1 1 1 1-2 1-2
CUSTOM SIZES 501-600 601-800 801-1100 1101-1300 1301-1600 1601-1800 1801-2000
Width (mm) 501-600 601-800 801-1100 1101-1300 1301-1600 1601-1800 1801-2000
Depth (mm) 400-500 400-500 400-500 400-500 400-500 400-500 400-500
Height (mm) 450 450 450 450 450 450 450
Number of Doors 1 2 2 2 4 4 4
Basin Options 1 1 1 1 1-2 1-2 1-2
To see the complete ISSY range go to www.reece.com.au/bathrooms
SPECIFICATIONSRecommended use Domestic, Commercial & Hotel
Materials Vanity Frame - Veneer & Solid American Oak
Bench Top - Corian
Timber Colours American Oak, Charcoal Oak, Pony Oak , Hazelnut Oak
Corian Colours Glacier White, Weathered Aggregate, Oyster, Deep Night Sky
Fixing (not included) Bolted / Screwed to Wall by a Licensed Trades Person
Basin Sold Separately, refer to Brochure
page 1 of 11
HALO I VANITY UNITFINISH OPTIONS
CLEANING RECOMMENDATIONSYour timber frame should be cleaned with a mild, non-acidic, non-abrasive detergent and soft cloth . Finish by cleaning off detergents with a soft damp cloth and towel dry. Always clean spills and water immediately.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
**Please ensure a copy of the installation instructions is left with the end user for future reference
DESIGN FEATURES:• Touch release door/s opening OR 150dia Corian Handle/s opening with soft close hinge• 45mm edge fixed support panel• Signature Halo routing door detail (Strips of Solid and Veneer American Oak)• American Oak Veneer carcass with standard Glacier White Corian Top (additional cost for Oyster, Weathered Aggregate &
Deep Night Sky)• Internal fixed shelf with Veneer lining
AMERICAN OAK HAZELNUT OAK WEATHERED AGGREGATEGLACIER WHITE
CORIAN OPTIONSTIMBER OPTIONS
PONY OAK CHARCOAL OAK DEEP NIGHT SKYOYSTER
150DIA CORIAN HANDLE OPTIONS
GLACIER WHITE DEEP NIGHT SKYOYSTER
**Corian handle and top to be in same finish
WEATHERED AGGREGATE
page 2 of 11
STANDARD SIZESHALO I VANITY UNIT
fixed support panel
500W x 450D x 450H
600W x 450D x 450H
1000W x 450D x 450H
1200W x 450D x 450H
1500W x 450D x 450H
1800W x 450D x 450H
fixed support panelfixed support panelfixed support panel
SIDE VIEW for all sizesINTERNAL VIEW for all size
page 3 of 11
fixed support panel
CUSTOM SIZESHALO I VANITY UNIT
501-600W x 400-500D x 450H
601-800W x 400-500D x 450H
801-1100W x 400-500D x 450H
1101-1300W x 400-500D x 450H
1301-1600W x 400-500D x 450H
1601-1800W x 400-500D x 450H
1801-2000W x 400-500D x 450H
fixed support panelfixed support panelfixed support panel
SIDE VIEW for all sizesINTERNAL VIEW for all size
page 4 of 11
STANDARD SIZES WITH CORIAN HANDLEHALO I VANITY UNIT
fixed support panel
500W x 450D x 450H
600W x 450D x 450H
1000W x 450D x 450H
1200W x 450D x 450H
1500W x 450D x 450H
1800W x 450D x 450H
fixed support panelfixed support panel
SIDE VIEW for all sizesINTERNAL VIEW for all size
fixed support panel
page 5 of 11
fixed support panel
CUSTOM SIZES WITH CORIAN HANDLEHALO I VANITY UNIT
501-600W x 400-500D x 450H
601-800W x 400-500D x 450H
801-1100W x 400-500D x 450H
1101-1300W x 400-500D x 450H
1301-1600W x 400-500D x 450H
1601-1800W x 400-500D x 450H
1801-2000W x 400-500D x 450H
fixed support panel fixed support panelfixed support panel
SIDE VIEW for all sizesINTERNAL VIEW for all size
page 6 of 11
STANDARD CORIAN CUTOUT
500 - 600W: CENTRAL ONLY
1000W: CENTRAL | OFFSET LEFT & RIGHT
1200W: CENTRAL | OFFSET LEFT & RIGHT
1500W: DOUBLE BASIN | OFFSET LEFT & RIGHT
1800W: DOUBLE BASIN | OFFSET LEFT & RIGHT
HALO I VANITY UNIT
*Suitable for recommended Counter Top Basins
page 7 of 11
45DIA CORIAN CUTOUT
500 - 600W: CENTRAL ONLY
1000W: CENTRAL | OFFSET LEFT & RIGHT
1200W: CENTRAL | OFFSET LEFT & RIGHT
1500W: DOUBLE BASIN | OFFSET LEFT & RIGHT
1800W: DOUBLE BASIN | OFFSET LEFT & RIGHT
*Suitable for recommended Vessel Basins
HALO I VANITY UNIT
page 8 of 11
500 - 600W: CENTRAL ONLY
1000W: CENTRAL | OFFSET LEFT & RIGHT
1200W: CENTRAL | OFFSET LEFT & RIGHT
1500W: DOUBLE BASIN | OFFSET LEFT & RIGHT
1800W: DOUBLE BASIN | OFFSET LEFT & RIGHT
HALO I SEMI-INSET** ROCA INSPIRA SEMI -INSET ROUND BASIN ONLY **
1500375 375
1500375
1500375
1800
450 450
1800
450
1800
450
Ø340 Ø340
Ø340 Ø340
Ø340
Ø340
Ø340
Ø340
1500375 375
1500375
1500375
1800
450 450
1800
450
1800
450
Ø340 Ø340
Ø340 Ø340
Ø340
Ø340
Ø340
Ø340
1500375 375
1500375
1500375
1800
450 450
1800
450
1800
450
Ø340 Ø340
Ø340 Ø340
Ø340
Ø340
Ø340
Ø340
500
600
1000
250
300
500
Ø340
Ø340
Ø340 Ø340 Ø340
Ø340 Ø340Ø340
1200
300
1200
300
1200
600
1000250
1000250
500
600
1000
250
300
500
Ø340
Ø340
Ø340 Ø340 Ø340
Ø340 Ø340Ø340
1200
300
1200
300
1200
600
1000250
1000250
500
600
1000
250
300
500
Ø340
Ø340
Ø340 Ø340 Ø340
Ø340 Ø340Ø340
1200
300
1200
300
1200
600
1000250
1000250
500
600
1000
250
300
500
Ø340
Ø340
Ø340 Ø340 Ø340
Ø340 Ø340Ø340
1200
300
1200
300
1200
600
1000250
1000250
1500375 375
1500375
1500375
1800
450 450
1800
450
1800
450
Ø340 Ø340
Ø340 Ø340
Ø340
Ø340
Ø340
Ø340
1500375 375
1500375
1500375
1800
450 450
1800
450
1800
450
Ø340 Ø340
Ø340 Ø340
Ø340
Ø340
Ø340
Ø340
1500375 375
1500375
1500375
1800
450 450
1800
450
1800
450
Ø340 Ø340
Ø340 Ø340
Ø340
Ø340
Ø340
Ø340
page 9 of 11
500 - 600W: CENTRAL ONLY
1000W: OFFSET LEFT & RIGHT
1200W: OFFSET LEFT & RIGHT
1500W: DOUBLE BASIN | OFFSET LEFT & RIGHT
1800W: DOUBLE BASIN | OFFSET LEFT & RIGHT
HALO I SEMI-INSET** ROCA INSPIRA SEMI -INSET SOFT SQUARE & SQUARE BASIN ONLY **
1500375
340
340
3751500
375
340
340
1500
340
340
375
1800
450 450
340
340
340
340
340
340
340
340
340
340
1800
450
1800
450
1500375
340
340
3751500
375
340
340
1500
340
340
375
1800
450 450
340
340
340
340
340
340
340
340
340
340
1800
450
1800
450
1500375
340
340
3751500
375
340
340
1500
340
340
375
1800
450 450340
340
340
340
340
340
340
340
340
340
1800
450
1800
450
500
600
1000
1200
250
300
500
340
340
340
340
340
340340
340
340
340
340
340
340
340
340
340
1000 1000
600
1200 1200
300 300
250 250
500
600
1000
1200
250
300
500
340
340340
340
340
340
340
340
340
340
340
340
340
340
340
340
1000 1000
600
1200 1200
300 300
250 250
1500375
340
340
3751500
375
340
340
1500
340
340
375
1800
450 450
340
340
340
340
340
340
340
340
340
340
1800
450
1800
450
1500375
340
340
3751500
375
340
340
1500
340
340
375
1800
450 450
340
340
340
340
340
340
340
340
340
340
1800
450
1800
450
1500375
340
340
3751500
375
340
340
1500340
340
375
1800
450 450
340
340
340
340
340
340
340
340
340
340
1800
450
1800
450
500
600
1000
1200
250
300
500340
340
340
340
340
340
340
340
340
340
340
340
340
340
340
340
1000 1000
600
1200 1200
300 300
250 250
500
600
1000
1200
250
300
500
340
340
340
340
340
340
340
340
340
340
340
340
340
340
340
340
1000 1000
600
1200 1200
300 300
250 250
page 10 of 11
1. To aid Installation; first remove doors by unscrewing the hinges. Doors will slide off hinge bracket. Place doors in a secure location in the meantime.
2. Check that the unit will fit into the location. On timber studded walls, mark the positions of the studs, so to be able to fix the unit to these later.
3. Line up the unit so that the units waste chamber aligns with the corresponding plumbing. Holes for waste outlet through the back are not pre-drilled. This outlet is left to the discretion of the plumber. Mark where unit is to be installed.
4. Mount unit by screwing through any part of the back of the unit into the wall, ensuring contact to studs.
5. Ensure Corian is right way up. Silicon to secure and mount permanently. Addtional Silicon is also required on the edge of the vanity where the Corian meets the tiles/ wall. If wall to wall, all four edges require Silicon.
6. Attach doors back on by sliding the hinges back on the bracket, and screw accordingly.
7. Ensure the vanity is installed level; as this will effect the alignment of the doors.
**Recommendation for Plumbing
Waste should not be over tightened to avoid stress on basin and top.
VANITY FITTING INSTRUCTIONSHALO I VANITY UNIT
Vanity should be installed by a qualified, licensed trade person.
Vanity Fitting Instructions
• Prior to installation it is important to inspect the vanity to ensure no damage has occurred in transit. If damage has occurred, or a visible defect exists, do not proceed with the installation and advise supplier immediately. No warranty claim for damage will be accepted if the vanity is installed.
• Prior to installation check wall/tile surface where unit will be fitted is flat and even. Installing on uneven wall will result in the unit twisting – DO NOT PROCEED.
• It is recommended that the Solid Surface Top is protected during installation.
PLEASE NOTE: MANUFACTURER WILL NOT BE LIABLE FOR THE COST OF INSTALLATION OR REMOVAL OF THE VANITY & THE WARRANTY WILL BE VOIDED IF DAMAGE OCCURRED DURING INSTALLATION.
1. Pull tag off
REMOVE DOOR
2. Push down clip and
remove door
HEIGHT ADJUSTMENT
1. Loosen the 2 screws on each side and lift door up and down, re-tighten screws.
SIDE TO SIDE ADJUSTMENT
1. Turn left/right for side to side adjustment.
2. Turn left to right for
depth adjustment.
SILICON
page 11 of 11