The Leading Source For Quality Products And Excellent Service!
Volume 10
www.intldoorclosers.com
Proud of our Past Focused on the Future
OHC ClosersSurface ClosersGate CloserDoor HardwareMiscellaneous HardwareStrikesDoor Holders, Stops & Flush BoltsThresholdsDoor SweepsAluminum Steel Pivots
Stainless Steel PivotsAluminum Geared HingesStainless Steel Pin & Barrel HingesButt Hinges & Power TransfersMechanical - Electrified Exit Devices & Escutcheon Trim Mechanical - LocksetsMechanical - Electrified Mortise LocksetsElectro-Magnetic Locks Access Controls
Underwriters’ Laboratories Inc. Listed. Two Speed Control Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation.
3010-DP dual purpose radial ball bearing bottom pivot set is standard for floor or threshold center pivoted installation. Optional 3010-GE bottom pivot sets are available, but must be ordered separately. Fits in an aluminum header or transom bar as small as 1 ¾” x 4”.
Cast Iron Body.
Positive centering for alignment and to hold door closed against a normal wind or draft.
Stable hydraulic door check fluid for any climatic operation and constant lubrication.
Built-in positive back stop and hold-open positions available:
105° Back Stop with Hold-Open
105° Back Stop - no Hold-Open
90° Back Stop with Hold-Open
90° Back Stop - no Hold-Open
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Overhead ConcealedSeries 200 & 200SA
Closers designed for ALL GLASS DOORS with a longer spindle
and short arm.
“S” Type Arm Shown. Other Type Top Arms
Also Available.
¾” spindle length for better door support
CENTER HUNG DOORS: Double or Single Acting Door (Door stop applied to frame renders unit Single Acting). “A” type short end loading top arm supplied for smaller top rail applications.
¾” spindle length for better door support.
Standard spring tensions available: MEDIUM or HEAVY
5-¾” Short “A” Arm (measured from center line of spindle to end of arm).
Series 200-SA All Glass Door Closer
CENTER HUNG DOORS: Double or Single Acting (Door stop applied to frame renders unit Single Acting). Adjustable “S” type side loading, “A” type, “K” type or “PT” type end loading arms are available for center pivoted applications.
OFFSET HUNG DOORS: Single Acting. Offset “JO” and “VO” type top arms are available for butt hinge or offset pivot applications.
ADA (Handicap) spring tensions available for use on center pivoted applications.
Standard spring tensions available: ADA, LIGHT, MEDIUM, and HEAVY
Series 200 Handicap & Standard
2
ADA (Handicap) multi-sized closer with Adjustable Spring Power for a range of sizes from 8½ lbs. of Opening Force to medium spring tension, and fully adjustable after installation.
Built-in positive back stop and hold-open positions available:
105° Back Stop with Hold-Open
105° Back Stop - no Hold-Open
90° Back Stop with Hold-Open
90° Back Stop - no Hold-Open
Series 300 Handicap Adjustable Spring Power
Series 500 - CERTIFIED GRADE 1 Adjustable Spring Power
Factory tested to meet or exceed ANSI 156.4 Grade 1
ADA (Handicap) multi-size closer with Adjustable Spring Power for a range of sizes from 5 lb. to Medium Spring Tension, fully adjustable after installation
Underwriters’ Laboratories Inc. Fire Endurance Tested, conforming to UL10C and UBC7.2 (1997) for Fire Safety.
Built-in positive back stop and hold-open positions available:
105° Back Stop with Hold-Open
105° Back Stop - no Hold-Open
90° Back Stop with Hold-Open
90° Back Stop - no Hold-Open
East: 800-225-6737 Fax: 615-885-0903
ADA (Handicap) multi-sized closer with Adjustable Spring Power Barrier Free Operation to comply with Federal Accessibility Standards (ADA) ANSI A 117.1.
Underwriters’ Laboratories Inc. Fire Endurance Tested, conforming to UL10C and UBC7.2 (1997) for Fire Safety.
Suitable for both Center Hung (Double or Single Acting) and Offset Doors.
Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation.
“S” type side loading, “A” type, “K” type, or “PT” type end loading top arms are available for center pivoted applications.
Offset “JO” and “VO” type top arms are available for butt hinge or offset pivot (may not meet handicap force requirements).
3010-DP dual purpose radial ball bearing bottom pivot set is standard for floor or threshold center pivoted installation. Optional 3010-GE bottom pivot sets are available, but must be ordered separately. Fits in an aluminum header or transom bar as small as 1 ¾” x 4”.
Stable hydraulic door check fluid for any climatic operation and constant lubrication.
Overhead ConcealedSeries 300 & 500
3
Model 44CI Adjustable Spring Power
Application for HIGH TRAFFIC doors
Cast Iron Body; Forged Steel Arm
Double Heat Treated Steel Pinion
All Weather Fluid
Non-handed
Adjustable 1 through 6; Standard with Back-Check
Universal application for Regular Arm, Top Jam, or Parallel Arm mounting
Standard Plastic Cover - non handed
10 year warranty
Attractive baked enamel finishes:
AL - Aluminum
DU - Storefront Bronze
Optional Features
Metal Cover
Hold-open arm
Stop only arm
Compliance Standards
ANSI/BHMA A156.4 Grade 1 Certified
UL/C-UL Listed
UL 10B and UL 10C Compliant for positive pressure
Certified to conform to UBC 7-2 (1997, UL 228)
Barrier Free Operation to comply with Federal Accessibility Standards (ADA); complying with ANSI A117.1 (4.13.11)
Surface ClosersModel 44CI & 5000
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Series 5000 5000 Series With Dress Cover 5050 Series Without Dress Cover ADA (Handicap) multi-sized closers with adjustable spring power for a range of sizes adjustable after installation: 5001 & 5051: 8 ½ lb. opening force to a size 5 5002 & 5052: 5 lb. opening force to a size 4 5003 & 5053: 5 lb. opening force to a size 4
CLOSER FUNCTIONS: 5001 & 5051; adjustable spring power with adjustable Back-Check controlled by a separate regulating valve, adjustable after installation.
5002 & 5052; adjustable spring power with adjustable delayed closing action controlled by a separate regulating valve, adjustable after installation.
5003 & 5053; Basic-adjustable spring power only.
4
Series 1800 Grade 1
Factory tested to meet or exceed ANSI 156.4 Grade 1
Barrier Free operation to comply with Federal Accessibility Standards (ADA) complying with ANSI 117.1
Narrow design permits installation on most glass and aluminum doors without adapters
Standard application for regular arm and Top Jamb installation; optional parallel arm installation (requires optional PA bracket.)
Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating valves, adjustable after installation. (Three valves with optional back-check)
Slim Plastic Cover or Full Cover (optional)
5 year warranty
Attractive baked enamel finishes:
AL - Aluminum
DU - Storefront Bronze
East: 800-225-6737 Fax: 615-885-0903
Surface ClosersSeries 800 & 1800
Underwriters’ Laboratories Inc. Listed Two Speed Control Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation.
Universal Application: Non-handed for standard, top jamb or parallel arm installation.
Rack and pinion mechanism contained in a high tensile precision cast aluminum housing.
Stable hydraulic door check fluid for any climatic operation and constant lubrication.
Furnished with regular, hold-open or fusible link hold-open arms.
Hold-open arms are adjustable for holding from 90° to 180°.
Attractive Baked Enamel finishes: AL - Aluminum DU - Storefront Bronze
Series 800 Standard Series 850 Adjustable Back-Check Series 880
Range of sizes: Standard : 851, 852, 853, 854, and 855 Back-Check : 883, 884 and 885
Series 880 has adjustable Back-Check function controlled by a separate regulating valve, adjustable after installation.
Regular arms are equipped with a 15% (+)(-) 7½% power adjustment bracket.
Hold-Open arms are adjustable for holding from 90° to 180°.
Narrow design permits installation on most modern glass and aluminum doors without adaptors.
5
Series 8050 Handicap Adjustable Spring Power
ADA (Handicap) multi-sized closers with adjustable spring power for a range of sizes adjustable after installation: 8051: 8 ½ lb. opening force to a size 5 8052: 5 lb. opening force to a size 4 8053: 5 lb. opening force to a size 4 8054: 8 ½ lb. opening force to a size 5
CLOSER FUNCTIONS: 8051; Adjustable spring power with adjustable Back-Check controlled by a separate regulating valve, adjustable after installation.
8052; adjustable spring power with adjustable Delayed Closing Action controlled by a separate regulating valve, adjustable after installation.
8053 & 8054; Basic-adjustable spring power only.
Series 8900 Grade 1 Door Closer (Handicapped approved and UL listed):
ADA (Handicap) multi-sized closers with adjustable spring power
Adjustable spring power 1 through 6 (adjustable after installation)
Two speed control valves allow closing and latching speeds to be controlled by valves
Adjustable backcheck
Standard sweep and latch speed
Standard Tri-packed for regular arm, top Jamb and parallel arm applications
Numerous accessories are available to allow for special installation or adaptability
Series 8900 Handicap Adjustable Spring Power Surface Mounted - Grade 1 Closer
Surface ClosersSeries 8050, 8900 & 9000
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Underwriters’ Laboratories Inc. Listed Two Speed Control Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation.
Universal Application: Non-handed for standard, top jamb or parallel arm installation.
Rack and pinion mechanism contained in a high tensile precision cast aluminum housing.
Stable hydraulic door check fluid for any climatic operation and constant lubrication.
Furnished with regular, hold-open or fusible link hold-open arms.
Hold-open arms are adjustable for holding from 90° to 180°.
Attractive Baked Enamel finishes: AL - Aluminum DU - Storefront Bronze
6
Series 9000 Adjustable Spring Power
Complies with ANSI A156.4 Grade 1
Barrier Free Operation to comply with Federal AccessibilityStandards (ADA): Complying with ANSI A117.1 (4.13.11)
ADA (Handicap) multi-sized closers with adjustable springpower for a range of sizes adjustable after installation.
CLOSER FUNCTIONS: Model 9001: adjustable spring power (8-½ lb. Opening Force to Size 5) with adjustable Back-Check controlled by a separate regulating valve.
Model 9003: adjustable spring power (5 lb. Opening Force to Size 4)
with both adjustable Back-Check and adjustable Delayed Closing Action controlled by separate regulating valves.
Furnished with a high impact molded PVC Dress Cover (door closer body casting is finished for use without the Dress Cover).
Pedestrian Gate Closers
SWINGER 300Pedestrian Gate Closer
Tough, Dependable and Vandal resistant.
2” x 4” x 12” 16 gauge galvanized Steel housing.
Gate closer manufactured for pedestrain gates.
Two Separate Closing and Latching valves adjustable after installation without removing the closer.
Non Handed (right or left swing)
Opens to full 105 degrees.
Fully adjustable top arm for proper gate alignment.
Adjustable zinc plated Bottom Hinge with sealed ball bearings rated for 350 lbs.
Designed to close gate into it’s latch position without slamming.
Adjustable spring power to accommodate various size gates.
Adjustable sealed bearing bottom hinge.
East: 800-225-6737 Fax: 615-885-0903 7
CG-4043 Cylinder GuardHardened steel security ring
Free-spinning beveled collar
For standard face 5 pin Mortise key cylinder
For use on Aluminum Doors
Furnished with retaining clip and two spacers
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Anodized Bronze
DT-1850“Long Throw” DeadlockCylinder backset available: 31/32”, 1-1/8” and 1-1/2”
Bolt 1-3/8” throw, made of 5 ply laminated steel with a hardened roller pin in a case hardened ply for maximum security.
Lock accepts standard 1-5/32” Mortise Key or Thumbturn Cylinders with AR MS-Type cam
DH-1820-H“Hook Bolt” DeadlockCylinder backset available: 31/32”, 1-1/8” and 1-1/2”
Bolt 13/16” throw, made of 5 ply laminated steel with a hardened roller pin in a case hardened center ply for maximum security.
Lock accepts standard 1-5/32” Mortise Key or Thumbturn Cylinders with AR MS-Type cam
DH-1820-S“Short Throw” DeadlockCylinder backset available: 1-1/8”
Bolt 13/16” throw, made of 5 ply laminated steel with a hardened roller pin in a case hardened center ply for maximum security.
Lock accepts standard 1-5/32” Mortise Key or Thumbturn Cylinders with AR MS-Type cam
DL-4510Deadlatch LockCylinder backset available: 31/32” and 1-1/8”
Field reversible for opposite hand
Key controlled dogging
Latchbolt 1/2” throw, Chrome plate with Delrin insert for smooth, quiet latching
Lock accepts standard 1-5/32” Mortise Key or Thumbturn Cylinders with AR MS-Type cam
SS - 4510 Strike included, US 26D Faceplates 1” x 6-7/8”Flat
Radius
Radius Weatherstripped
Left Hand Beveled
Right Hand Beveled
Hardware
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-22158
DT-1850
DL-4510
DH-1820-H
DH-1820-S
CZ-1001 (Zinc)Mortise Key Cylinder1” Length 5 pin Cylinder 1-5/32” diameter
AR MS-Type cam
Keyway available: Schlage “C”, Yale “8”
Core face and Key US 26D
Cylinder ring 3/16” standard, 5/32” and 7/32” optional
Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
Removable CoreMortise Key Cylinder
DC-2001 (Zinc)Mortise Dummy Cylinder7/8” Length Cylinder 1-5/32” diameter
No Key or cam
Cylinder ring 3/16” standard, 5/32” and 7/32” optional
Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
RZ-1003 (Zinc)Rim Cylinder5 pin Cylinder
Core face and Key US 26D
Schlage “C” Keyway
Low profile Cylinder ring and adaptor plate standard
1-7/8” Break-away screws and 1-1/4” Break-away Spindle standard
Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
TZ-3001 (Zinc)Mortise Thumbturn Cylinder1” Length Cylinder 1-5/32” diameter
AR MS-Type cam
Thumbturn US 26D
Cylinder ring 3/16” standard, 5/32”and 7/32” optional
Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
LI-4089 Lock Indicator SetFor use with DH-1820 and DT-1850 Type Deadlocks
LOCKED in red and OPEN in green letters on white background
Includes adhesive backed HS-4089 Header Sign, “THIS/THESE DOORS TO REMAIN UNLOCKED WHEN THE BUILDING IS OCCUPIED”
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Anodized Bronze
East: 800-225-6737 Fax: 615-885-0903
526
Mortise Cylinder
Regular Type
Interchangeable Core Type
Rim Cylinder
208
426
308
9
PH-4520 Paddle Handle
For use with DL-4510 type Latch Lock
“Push” or “Pull” Paddle Handle
Field reversible for opposite hand with PUSH and PULL Plates included
Cam Plug, field reversible, included
Extruded Aluminum Handle
Finishes Available: AL - Handle anodized Satin Aluminum Housing baked Satin Aluminum paint DU - Handle anodized Storefront Bronze Housing baked Storefront Bronze paint
CP-4560 Cam Plug
For use with HL-4560 Lever Handle and PH-4520 Paddle Handle
HL-4560 Lever Handle
For use with DL-4510 type Latch Lock
Cam Plug, field reversible, included
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-221510
1” Diameter Solid Aluminum Round
3-1/4” Offset
Projection 3-1/4”
Door Clearance 2-1/4”
CTC 9”, 10” and 12”
Mounting Hardware Included Finishes Available: (Other Finishes Available on Request)
AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
PH-4000 Offset Door Pull
PH-4000-2 Offset Door Pull Set
1” Diameter Solid Aluminum Round
Projection: See Pull/Push Specifications
CTC: See Pull/Push Specifications
Mounting Hardware Included Finishes Available: (Other Finishes Available on Request)
AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
PP-1000 Offset Pull & Single Bend Push Bar Set
PP-2000Offset Pull & Double Bend Push Bar Set
1” Diameter Solid Aluminum Round
Projection: 2-1/4” with 1-1/4” Door Clearance
CTC: 33-1/16”, 39-1/16” and 45-1/16”
Mounting Hardware Included Finishes Available: (Other Finishes Available on Request)
AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze
PB-1000 Single Bend Push Bar
PB-2000Double Bend Push Bar
TYPE 1: Thru Bolt
TYPE 5: Back To Back Concealed
TYPE 6: Surface Mount Concealed
Mounting Hardware Various Combinations
East: 800-225-6737 Fax: 615-885-0903 11
SC-4540-1 & SC- 4545-1Strike SetsUse for the new installation of a DL-4510 Type Deadlatch Lock in a Center Hung Door and Frame
Non-handed Stainless Steel Strike for Left or Right hand installation
Dustbox, back-up plate, and screws included
SC-4540-1 for use on 4” door jamb
SC-4545-1 for use on 4-1/2” door jamb
SC-4510Strike SetUse for the new installation of a DL-4510 Type Deadlatch Lock in an Offset Door and Frame
Non-handed Stainless Steel Strike for Left or Right hand installation
Dustbox, back-up plate, and screws included
SC-4510 Strike SetUse for the new installation of a DL-4510 Type Deadlatch Lock in an Offset Door and Frame
Non-handed Stainless Steel Strike for Left or Right hand installation
Dustbox, back-up plate, and screws included
SS-4510 Standard Strike
SS-4510 Mounting holes press formed countersink
Non-handed Stainless Steel Strike for Left or Right hand installation
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Electric Bolt Lock Auto relock switchBolt and door status optional12/24 VDC operation
FS23MIV Dual failsafe, CSFM Listed1091AIV Failsafe1291AHV Failsecure
Provides latchbolt and deadbolt status delayed egress activation, alarm shunt, and mantrap communicationAuto relock switchBolt and door status optional12/24 VDC operation
MS-12 Cylindrical latch status 2-3/4” MS-14 Cylindrical latch status 4-7/8” MS-16 Mortise lock latch status MS-18 Mortise deadbolt status MS-20 Mortise latch & deadbolt status
Strike Latch Monitoring Kits
15 Series Electric StrikeFor up to 3/4 “ latchbolts Choice of failsafe / failsecure Non handed 12 or 24VDC
15-4F12U 4.875”, Fail Safe 12VDC15-4S12U 4.875”, Fail Secure 12VDC15-4F24U 4.875”, Fail Secure 24VDC15-4S24U 4.875”, Fail Secure 24VDC
25 Series Electric StrikeFor up to 5/8 “ latchbolts Field selectable failsafe/failsecureField selectable 12/24V AC/DCLatch status outputNon handed reversible
25-4U 4.875”, 300mA @ 12/24VDC25-6U 6.875”, 300mA @ 12/24VDC
12
East: 800-225-6737 Fax: 615-885-0903
45-4SU 4 7/8” square corners stainless steel
45-6RVU 6 7/8” radius corners
55-A 55-B/C 55-DE
55-ABC
55-F
45-A Universal Includes: 4 7/8” square corners4 7/8” radius corners7 15⁄16” radius corners
45-7RV 7 15/16” radius corners
45-4RV 4 7/8” square corners stainless steel
UniFLEX™ 45 SeriesFull Featured Electric Strike
For up to ¾” latchboltsField reversible failsafe/failsecureField selectable 12/24V AC/DC1/4” horizontal alignment adj.Latch position status SPDT std.Keeper closed & deadlocked status SPDT std.Low profile 1-3/16” deep
UniFLEX™ Application Specific Strike
UniFLEX™ Universal Strike
Up to ¾” Latchbolt and 1” DeadboltField Reversible, Failsafe/Failsecure1/8” Horizontal alignment adjustmentDual Voltage 12/24VDC Exceeds 1,000,000 cyclesFactory tested 2500 lbs static strength UL 1034 Burglary-Resistant Warnock Hersey Tested according to: UL 10C, 3 Hr Fire Rated NFPA-252 CAN4-S104 (ULC-S104)
55-ABC Universal Strike for cylindrical locks, mortise locks without deadbolts and mortise exit devices, including: SDC, Accurate, Arrow, Baldwin, Best, Corbin Russwin, Dorma, Falcon, Hager, Marks, Sargent, Schlage, Yale
CM
CM
13
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
TB-4015 & TB-4016Threshold Bolt KitTB-4015: For doors with cylinder height up to 53-1/2”. Threaded rod can be cut for cylinder heights lower than 53-1/2”
TB-4016: For doors with cylinder height 34” to 37”.
Bolt 3/8” hexagon hardened steel
11/16” bolt throw
Unit complete for attachment to basic Deadlock to provide two-point security
HB-4015-NSpecial Header Bolt SetStandard for 84” Doors with Cylinder Heights of not less than 33” ER-4015-N Extension Rod Kit is available for 8’-9’ Door Heights
14
DH-6000 Heavy Duty Kick Down Holder
Zinc Alloy Construction
Non-Marking Rubber Shoe
7” Body Height
Comes with Mounting Screws
Finishes Available: AL - Aluminum DU - Storefront Bronze
1000SL Slim LineHeavy Duty - Concealed
For exterior, vestibule or interior single or double acting doorAll stainless steel components Prefix N (Stop Only)3/4”maximum channel depthMaximum door opening 110o,minimum door thickness 1-3/4”
9000 SeriesHeavy Duty - Surface Mount
For exterior, vestibule and interior single acting doorsAll stainless steel components - Prefix NHold-open can be disengaged to act as a stop onlyMaximum door opening 110°,minimum door thickness 1-3/4”Available in all BHMA finishes including US32 & US32D
Additional Door Stops are available, see Master Catalog
East: 800-225-6737 Fax: 615-885-0903
HS-4089Header SignFor use on transoms and door headers
One piece, self-adhesive decal
Black letters on aluminum background
HB-4085, HB-4086 & HB-4087Header Bolt Set HB-4085: For doors 30-1/2” to 50” from Centerline of cylinder to top of door
HB-4086: For doors 55-5/8” to 77-1/2” from Centerline of cylinder to top of door
HB-4087: For doors 67” to 89” from Centerline of cylinder to top of door
Interactive leaf lock when used with basic Long Throw Deadlock in active leaf
5/8” throw expanding bolt
Minor adjustments can be made after installation
Unit complete with Rod Guide and Header Strike
15”/16” x 4-1/4” Radius Face
Positive “U” joint actuator with 5/8” throw 1/8”, 3/16” and 1/4” offset with 7/8” backset
Rod length for 12” Centerline of face installation
Square Nylon Tip with beveled corners fits in 1/2” square hole
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint
FB-1201: 1/8” offset, without guide FB-1202: 1/8” offset, with guide FB-1203: 1/4” offset, without guide FB-1204: 1/4” offset, with guide FB-1205: 3/16” offset, without guide FB-1206: 3/16” offset, with guide
FB-1200 Flushbolt
15”/16” x 4-1/4” Radius Face
Positive “U” joint actuator with 5/8” throw 1/8” offset with 11/16” backset
Square Nylon Tip with beveled corners fits in 1/2” square hole
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint
FB-1201-K Flushbolt
1/4-20 x 12” Threaded rod
Includes coupler
ER-1200 Flushbolt Extension Rod
For use with FB-1200 and FB-2200 Flushbolts
FG-1200 Standard Flushbolt Guide
For use with FB-1200 and FB-2200 Flushbolts
FG-1250 Extension Hole Flushbolt Guide
FB-2200 Flushbolt15”/16” x 4-1/4” Radius Face
Positive “U” joint actuator with 7/8” throw 1/8”, and 1/4” offset with 7/8” backset
Rod length for 12” Centerline of face installation
Square Nylon Tip with beveled corners fits in 1/2” square hole
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint
FB-2201: 1/8” offset, without guide FB-2202: 1/8” offset, with guide FB-2203: 1/4” offset, without guide FB-2204: 1/4” offset, with guide
THIS/THESE DOORS TO REMAIN UNLOCKED WHEN THE BUILDING IS OCCUPIED
15
Saddle ThresholdsIDC413, IDC513 and IDC713
Available in 36” and 48” lengthsCustom sizes and colors availableFinishes Available: Aluminum mill finish DKB - Aluminum dark bronze
Saddle ThresholdsIDC424E, IDC425E and IDC427E
Available in 36” and 48” lengthsCustom sizes and colors availableFinishes Available: Aluminum mill finish DKB - Aluminum dark bronze
Typical Wall .125
4"
1/4"
Typical Wall .125
5"
1/4"
Typical Wall .1257"
1/4"
IDC413 / IDC413DKB
IDC513 / IDC513DKB
IDC713 / IDC713DKB
Typical Wall .109
4"
1/2"
Typical Wall .109
5"
1/2"
Typical Wall .109
7"
1/2"
IDC424E / IDC424EDKB
IDC425E / IDC425EDKB
IDC427E / IDC427EDKB
Thresholds
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-221516
Available in 36” and 48” lengthsCustom sizes and colors availableFinishes Available: Aluminum mill finish DKB - Aluminum dark bronze
Door Sweeps & Brush SealsIDC97V - Vinyl Sweep
Products are UL10B and Can4-S104-80M Classified, complies with NFPA 80 and NFPA 252 for application to Steel fire doors rated up to 3 hrs., and wood type fire doors treated up to 1-1/2 hrs.
Positive Pressure UL10C Classified, Category “J” Complies with IBC UBC7-2 (1997) NFPA 80 & 252
Smoke & Draft Control Gasketing, Category “H” Complies with IBC7-2 (1997) Part 2, UL1784, NFPA 105 for use on “S” labeled Positive pressure Steel fire doors up to 3 hours and wood type fire doors rated up to 1-1/2 hours
Air Filtration Tested to ASTM E283, Standard Test Method for Determining Rate of Air Leakage through Exterior windows, Curtain Walls and Doors
#6 x 3/4” stainless steel SMS furnished and Screw holes are slotted for adjustment
Available colors: Clear, Gold and dark bronze. Vinyl is standard gray, bronze frame has black vinyl
Stock sizes 36” and 48”, custom sizes available
Door Sweeps & Brush SealsIDC601 - Nylon Brush Seals
Synthetic polymer: Polyamide bristles
Excellent abrasion resistance, flexibilty and memory
Moisture resistant
Retains insecticides well
Temperature range -70F to 160F
BHMA Certified to ANSI A156.22 performance tests for Heat, Cold, Air Leakage and Smoke Control in most common profiles
Not effective against water penetration
#6 x 3/4” Stainless Steel sheetmetal screws furnished. Screw holes are slotted for adjustment
Available colors: Clear with gray brush, Gold with black brush and Dark Bronze with black bush
Stock sizes 36” and 48”, custom sizes available
1"
vinyl
7/8"
IDC97V
IDC601
9/32"
3/4"
9/16"
IDC673
1"7/
8"
nylon brush
1"
vinyl
7/8"
IDC97V
IDC601
9/32"
3/4"
9/16"
IDC6731"
7/8"
nylon brush
Door Sweeps & Brush Seals IDC673 - Concealed Fastener Nylon Brush Sweeps
Synthetic polymer: Polyamide bristlesExcellent abrasion resistance, flexibilty and memoryMoisture resistantRetains insecticides wellTemperature range -70F to 160F
BHMA Certified to ANSI A156.22 performance tests for Heat, Cold, Air Leakage and Smoke Control in most common profilesNot effective against water penetration
#6 x 3/4” Stainless Steel sheetmetal screws furnished. Screw holes are slotted for adjustment
Available colors: Clear with gray brush, Gold with black brush and Dark Bronze with black brushStock sizes 36” and 48”, custom sizes available
1"
vinyl
7/8"
IDC97V
IDC601
9/32"
3/4"
9/16"
IDC673
1"7/
8"
nylon brush
Door Sweeps
East: 800-225-6737 Fax: 615-885-0903 17
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Offset Pivot Sets
3/4” Offset for use with Aluminum Doors and Frames
Oilite bronze bushing in top frame portion
Case hardened stud in floor/jamb portion (stainless steel stud in Series 5000 floor/jamb portion)
Case hardened, spring loaded pin in top door portion (case hardened fixed pin in Series 5000 top door portion)
Full race ball bearing in bottom door portion
1/8” vertical adjustment
For doors up to 125 lbs.
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint
Series 2000 Offset Pivot Set
Series 3000 Offset Pivot Set
OP-2700: Flush DoorOP-2700: 1/8” Recessed Door
Series 4000 Offset Pivot Set
OP-4001: Left Flush DoorOP-4002: Right Flush Door
OP-3001: Left Flush DoorOP-3002: Right Flush DoorOP-3101: Left 1/8” Recessed DoorOP-3102: Right 1/8” Recessed Door
Series 5000 Offset Pivot Set
OP-5001: Left 1/8” Recessed DoorOP-5002: Right 1/8” Recessed Door
Series 6000 Offset Pivot Set
OP-6001: Left 7/64” Recessed DoorOP-6002: Right 7/64” Recessed Door
Series 2000
Series 3000
Series 4000
Series 6000
Series 5000
18
East: 800-225-6737 Fax: 615-885-0903
A380 Precision die cast aluminum
Oilite bronze bushing in top frame portion
Full race ball bearing in bottom door portions
Door height adjustable by bottom door portion
Case hardened stud in floor/jamb portion
Includes steel reinforcement plates for the door portions
OP-7001 (Left) OP-7002 (Right)
OP-7000 Offset Pivot Set (Kawneer Type)
Non-Handed Offset Top and Bottom Pivot Set
For Use With 1-3/4” (44.4 mm) Aluminum Doors
Maximum Door Weight is 125 Pounds (57 Kg)
1689 Non-Handed Offset Pivot Set
1689
Bottom Pivot
Floor Mount Bottom Pivot Set for use with 1” deep Bottom Door Rail
600-PSFloor Mount
OP-7000
19
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Intermediate Pivots
3/4” Offset for use with Aluminum Doors and Frames
Full race ball bearing baked by an oilite bronze bushing in the door portion
Case hardened pin in jamb portion fully retractable for ease of installation
Easy vertical adjustment
Precision Aluminum die cast
For doors up to 125 lbs.
IP-1901 (Left) IP-1902 (Right)
IP-1900 Intermediate Pivot Set
Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint
Center Hung PivotsSeries 400
For use with Aluminum Doors and Frames
400-PF mounting holes drilled & tapped400-PF1 mounting holes drilled & countersunk
For use with 400-PF1 only
400-PF Top Pivot Frame Portion
400-PC Dress Plate Frame Portion
400-PD Top Pivot Door Portion
3/4” Offset for use with Aluminum Doors and Frames
Full race ball bearing baked by an oilite bronze bushing in the door portion
Case hardened pin in jamb portion fully retractable for ease of installation
Easy vertical adjustment
Precision Aluminum Extrusion
For doors up to 125 lbs.
IP-2201 (Left) IP-2202 (Right)
IP-2200 Intermediate Pivot Set
IP-2200
IP-1900
20
East: 800-225-6737 Fax: 615-885-0903
E019
019
Pivot sets include top and bottom pivots.Offset pivot sets are handed and require an
intermediate pivot to accommodate the door weights listed for each set. Door edges
must be beveled 1/8”in 2”.All sets are available in standard architectural finishes.
Intermediate pivots are used to keep doors in alignment. All intermediate pivots are
offset hung and cannot be used on center hung doors. Per NFPA 80, fire doors are
to have an intermediate pivot for additional 30”or fraction thereof for door heights
over 6’. Available in most architectural finishes.
Stainless Steel Offset Pivots
Stainless Steel Intermediate Pivots
3/4”offset
For interior doors up to 4’0”x 8’0”
Weight to 300 lbs.
0180 top pivot included
019 intermediate pivot required
Bottom pivot mortised into floor
US32D models UL listed for use on 3 hour fire doors
Extended spindles available
BHMA/ANSI C07162/3530A (modified)
0117Stainless Steel Offset Pivot
3/4”offset,handed
Full mortise
Needle bearing supplied standard.
Can be used on heavy duty doors
US32D models UL listed for use on labeled doors
BHMA/ANSI C07321/3525
019Stainless Steel Intermediate Pivot
3/4”offset
For interior doors up to 4’0”x8’6”
For exterior doors up to 3’6”x 7’0”
Weight to 600 lbs.
0180 top pivot included
019 intermediate pivot required
Bottom pivot mounted to floor
US32D models UL listed for use on 3 hour fire doors
BHMA/ANSI C07162/3530A (modified) Extended
spindles available
0147Stainless Steel Offset Pivot
3/4”offset,handed
Full Mortise
Can be used on heavy duty doors
US32D models UL listed for use on labeled door
(8) 28ga. wires supplied standard*
Door and jamb portions are factory assembled
*Pivot cannot be separated for installation
E019Stainless Steel Power Transfer Offset Pivot
21
Continuous Hinges
Stainless Steel Continuous Hinges
UL listed for all Models (except 130) for the following rated doors: Swing Type Metal and Wood Doors up to 1 hour without Fire Studs Swing Type Wood Doors up to 1-1/2 hour with Fire Studs Swing Type Metal Doors up to 1-1/2 hour without Fire Studs Swing Type Metal Doors up to 3 hours with Fire Studs
Size: 83”, 85”, 95”and 120”are standard – Other sizes available
IDC Continuous Gear Hinges are all heavy duty. All hinges have double the number of
bearings of standard duty hinges and are pinless. There are no accessible screws, bolts or
pins when the door is closed. IDC gear hinges are surface applied to the frame and door.
No machining is required. Whether surface mount or concealed, the IDC continuous gear
hinges eliminate the gap between the door and frame, and provide a weatherproof,
tamper-proof barrier. The IDC gear hinges templated and the hole pattern is the same
from hinge to hinge.
IDC Stainless Steel Hinges are made of 304 Stainless Steel. Continuous Stainless Steel Hinges run the entire length of the door
eliminating any gaps between the door and the frame, providing high security and also distributing the weight of the door
evenly through the opening. Continous Stainless Steel Hinges are ideal for highly abusive & corrosive applications such as
hospitals, water treatment plants, swimming pools, and salt spray applications are utilized.
No exposed Fasteners when door is closedElectrical modifications available
Heavy-Duty 14 Gauge 304 Stainless Steel.US32D Satin Stainless SteelSelf drilling screwsSupports door weights up to 600 lbs.4’-0” Maximum door widthNominal Sizes 7’, 8’ & 10’ are Non-handed6’8” & 7’2” are handed hinges1/4” diameter stainless steel pin
UL fire rated: Hollow Metal doors - 3 Hours Hollow Metal & Composite wood fire - 90 Min Wood doors - 20 Min
Decorative Fastener CoverTemplatedCurrent transfer prep available
IDCA500 Full Concealed Edge Mount
IDCA503 Half Surface
IDCA502 Full Surface Flush Mount
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
IDCA500 Full Concealed Edge Mount IDCA502 Full Surface
Flush Mount
IDCA570 Full Surface For Narrow Frames
IDCA571HD Full Surface
IDCA110 Concealed
IDCA210HD Full Surface Swing Clear
IDCA503 Half Surface
22
Stainless Steel Edge Guards
No exposed Fasteners when door is closedTemplated
No exposed Fasteners when door is closedTemplatedElectrical modifications available
Heavy-Duty 16 Gauge 304 Stainless Steel.US32D Satin Stainless SteelNo exposed Fasteners when door is closedSelf drilling screwsNominal sizes 6’8”, 7’, 7’2”, 8’ & 10’Symmetrically templated, Non HandedHardware cut-outs available
Specify when ordering: Square edge door or Beveled edge door
No exposed Fasteners when closedAdjustable to accommodate variances in door thicknessTemplatedElectrical modifications availableWrap around guard protects from unslightly gouges and dents and also protects from further damage. Load of the door is distributed along the entire length of jamb.Square Edge Hinge side door only
Decorative Fastener CoverTemplatedCurrent transfer prep available (door leaf only)
Decorative Fastener CoverTemplatedCurrent transfer prep available (door leaf only)
IDCA511 Full Concealed Swing Clear With Edge Guard
IDCA515 Full Concealed With Edge Guard
IDCA505 Full Concealed Edge Guard
IDCA504 Surface Mounted
IDCA506 Surface Mounted
East: 800-225-6737 Fax: 615-885-0903
IDCA504 Surface Mounted
IDCA505 Full Concealed Edge Guard
IDCA506 Half Surface With Edge Guard
IDCA511 Full Concealed Swing Clear With Edge Guard
IDCA515 Full Concealed With Edge Guard
IDCA528 Edge Guard with 1 Lip Only
IDCA538C Full Edge Guard
IDCA548T Full Edge Guard With Astragal
23
Butt Hinges
Power Transfers
UL 10B listed for 3 hr fire doors4 foot cable (standard)Optional DPS
PTH-4Q 4 wires, 1 Amp PTH-2-4Q 6 wires, 1 pair - 16 Amp inrush, 2 Amp continuous, 2 pair - 1 AmpPTH-10Q 10 Wires, 1 Amp DPS Door status contact, optional
Power Transfer Hinge
IDC’s heavy duty Electric Power Transfer Device provides a concealed and secure means of transferring electric lock and exit device power and signal wires from the frame to the door. Completely concealed when the door is closed the PTM Electric Power Transfer Device is ideal for heavy traffic and applications requiring higher security to inhibit tampering and abuse.
Electric Power Transfer Device
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
Size: 4.0”x4.0” 4.5”x4.0” 4.5”x4.5” 5.0”x5.0” Other specs are available. Please contact us!
Finishes Available: US3, US4, US10, US10B, US26, US26D, US32, US32D, White, etc.
Options: NRP (Non-Removable Pin)
IDCAHP Series5 Knuckle 2 Bearing
IDCAHA Series5 Knuckle 2 Bearing
IDCAH SPR SeriesSpring Hinge
24
IDCAHA 4545 PB
PTH
PTD
IDCAHP 4545 PB - NRP IDCAHP 4545 BB - NRP
IDCAH SPB 4545 Spring Hinge
Escutcheon Trim
Series 8000Trim has 4 through-bolts to the device chassis directly for better security and
durability. It fits 1-3/4” (44) door standard. For 2” (51mm), 2-1/4” (57mm) thick
door or the shim-mounted exit device, specify the door thickness when ordering.
Clutch freewheeling design. The lever rotates when the door is locked,
preventing excessive force from being applied to the horizontal lever.
East: 800-225-6737 Fax: 615-885-0903
Mechanical Exit Devices
All devices are non-handed design
Slight pressure on device touch bar will retract latch(s) for immediate exit
Auxiliary guarded latch deadlocks latch bolt automatically when door is closed High shock-resistant latching mechanical design for protection from vandalism
All inside components are made of high rust-resistant alloy or heavily electroplated steel
Anti-fading, electroplated or architectual base material finishes on all exposed surfaces are available
With a dogging mechanism, users have a choice of hex-key or cylinder operated for positive push-pull action at peak traffic time. This dogging device will also help by increasing the life of the exit device (panic label only).
Available in Wide or Narrow Stiles, Surface Vertical Rod (SVR), Concealed Vertical Rod (CVR)
Less Bottom Rod (LBR) and Rim or Mortise locks
IDC 8000 Series Exit Devices are heavy duty and designed for heavy
traffic applications. The devices are Underwriters Laboratory (UL,
USA and ULC, Canada) listed for PanicExit Hardware or Fire Exit
Hardware, and are certified to ANSI A156.3-2001 Grade 1.
8000 Series Exit Device – Grade 1Panic and Fire Rated
Surface Vertical Rod Exit Device
Concealed Vertical Rod Exit Device
Electrical Trim Field reversible fail safe / ≠fail secureAudible tone when energized4 ft cable and connectors600/300 mA @ 12/24VDC
OperationOptions
Key Locks & UnlocksLever
Lever Always Active(No Cylinder)
KeyRetracts Latchbolt(Rigid Lever)
Pull When Dogged(Rigid Lever)
Functions Classroom Passage Storeroom Dummy
Model Number& Application
89L01A 89L01B
For Rim, Surface / Concealed Vertical Rod, LBR Exit Devices Use
For Mortise Lock Exit Devices Use Only
89L01C 89L01D
89E01A 89E01B 89E01C 89E01D
Trim Designation CylinderEscutcheon Lever
BlankEscutcheon Lever
Night LatchEscutcheon Lever
Dummy Escutcheon Lever
Rim Mount Exit Device
Mortise Exit Device
25
Simultaneous Latch Retraction & DoggingField RetrofitUL Listed When IDC Factory InstalledQuiet Motor Operation450 mA Inrush, 180 mA Continuous
Compatible other Manufactures Exit Devices Von Duprin 98/99 Series, 33/32 Series, 22 Series and other manufacture devices
IDC LR100 SeriesLatch Retraction - For 8000 Series Exit Device
Electrified Exit Device
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
E Electric Latch Retraction For 6100, 6200, 6300, 6800 Example: S6101F-RR-36-U-E
Operation: Momentary or maintained latch bolt and push pad retraction
Voltage: 12/24VDC @ 1 Amp activation, 180 mA continuous
EMC: Sequencer Module required for pair of doors and automatic doors. 12/24VDC. Installed in power supply
Monitoring: See S6000 Spectra datasheet for details
602RF 1 Amp power supply (1 EMC max) 632RF 2 Amp power supply (2 EMC max) Electrified Mortise Exit Device
MortiseM Electric Mortise Exit Device Example: S6303F-LR-U-36-M x GK03U
Field reversible fail secure / fail safe. Remains latched when unlocked for fire door integrityFailsafe (F) fire rated device for stairwell doorsPower loss or signal from fire command center releases fail safe device immediately
Voltage: 1600/300 mA @ 12/24VDC
Monitoring: See S6000 Spectra datasheet for details
1 Amp Electric Latch RetractionRim Mount, Vertical Rod & Mortise
G Electric Dogging (failsecure) 6100, 6200, 6300, 6800 Example: S6103P-LR-U-36-G x SP03U
When energized by optional built-in or remote switch manual, depressing the pushpad, causes the pushpad and latch to remain retracted (unlocked) providing push-pull door operation. When de-enegrized or signaled by a fire alarm, the pushpad and latch are released.
Voltage: 170/100 mA @ 12/24VDC
Monitoring: See S6000 Spectra datasheet for details
Electrified DoggingRim Mount, Vertical Rod & Mortise
26
Simultaneous Latch Retraction & DoggingField RetrofitUL Listed When IDC Factory InstalledQuiet Motor Operation450 mA Inrush, 180 mA Continuous
Compatible other Manufactures Exit Devices Von Duprin 98/99 Series, 33/32 Series, 22 Series and other manufacture devices
IDC LR100 SeriesLatch Retraction - For 8000 Series Exit Device
500 Series Exit Device REX Switches27 SPDT & DPDT 5 Amp switch kitsRetrofit mechanical exit devicesRequest-to-Exit & alarm shuntDelayed egress activationMagnetic lock release
Switch kits available for Von Duprin, Yale, Sargent, Adams Rite, Arrow, Cal Royal, Corbin, Dor-O-Matic, Jackson, Kawneer, Monarch, Precision
East: 800-225-6737 Fax: 615-885-0903
Exit AlarmRim Mount, Vertical Rod & Mortise
Electric Frame ActuatorHitower Pro Frame Actuator Controlled Fire Exit Device
No wiring through door No door transfer hinge
A Exit Alarm, 9V battery poweredB Exit Alarm, 12-24V AC/DC input, 9V battery backup For 6100, 6200, 6300, 6800 Example: S6801P-LR-U-36-A
100 dB alarm; visual and audible On/Off status:Armed - green LED blinks every 4 seconds, Alarm mode - red LED, Bypass - no LEDRemote status output15 or 60 second arming delay2 modes: Continuous alarm with manual key reset; Automatic re-arm 2 minutes after door closes with any manual key reset before 2 minutes.
Options: 6, 10 & 20 minutes alarm; 1 or 5 second re-arm delay Remote access control, arm, disarm inputs REX and latch status outputs
Features include failsafe operation and unlocks by access control, power loss or signal from fire command center. Door stays latched even when unlocked. All wiring is maintained in the strike jamb. Complies with national building and fire codes
Specify Voltage: 24VDC, 24VAC, 115VAC
Monitoring: See S6000 Spectra datasheet for details
Delayed Egress
DE Wall mount delayed egress controller with keypad and electrified exit device, 6100, 6200, 6300, 6800 Example: S6101F-R-U-36-DE x GK03UKDE Keypad controller with redundant key switch capable of all keypad control features 602RF 1 Amp power supply
User PIN codes may be assigned to 1, 2 or all control functions. Reset, sustained bypass and momentary bypass (RES). Audible alarm voice release time, warning or safety messageVisual display countdown, locked/unlocked, egress executed15 or 30 second exit delay, 1 or 2 second nuisance delay
Monitoring: See S6000 Spectra datasheet for details
27
Series 5000Trim has two through-bolts to the device chassis directly for more security and
durability. It fits 1-3/4” (44) door standard. For 2” (51mm), 2-1/4” (57mm) thick door
or the shim-mounted exit device, specify the door thickness when ordering.
This series trim is Anti-Vandalism design that can prevent the lock from damaging
when key locks the lever in rigid and horizontal position.
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steel
Baked powder coating, electroplated or architectual base finishes are used on all exposed surfaces
Outside trims are provided by rose and escutcheon lever or knob in a varity of styles
All trim features a through-bolted design to the devices that allow easy installation but not to comprise on security
With a dogging mechanism, users have a choice of hex-key or cylinder operated design for a positive push-pull door action during peak traffic time
Available in Wide or Narrow Stiles, Surface Vertical Rod (SVR), Concealed Vertical Rod (CVR), Rim and Mortise Locks
International Door Closers IDC 5000 Series Exit Devices meet the Life and Fire Safety Codes as prescribed by UL and
ANSI / BHMA 156.3 standards. These durable devices are designed for both standard and commercial applications.
The 5000 Series were tested and approved by Underwriters Laboratories (UL, USA and ULC, Canada) and listed to
comply with UL 10C, and Uniform Building Code Standard 7-2, “Fire Test of Door Assemblies” (1997).
5000 Series Exit DevicePanic and Fire Rated
Narrow Design Panic SVR Exit Device
OperationOptions
Key Locks & UnlocksLever
Lever Always Active(No Cylinder)
KeyRetracts Latchbolt(Rigid Lever)
Pull When Dogged(Rigid Lever)
Functions Classroom Passage Storeroom Dummy
Model Number& Application
58L01A 58L01B
For Rim, 5510 Series Rim, 5530 Series Surface Vertical Rod
58L01C 58L01D
Trim Designation CylinderEscutcheon Lever
BlankEscutcheon Lever
Night LatchEscutcheon Lever
Dummy Escutcheon Lever
Mechanical Exit Devices
526
Mortise Cylinder
Regular Type
Interchangeable Core Type
Rim Cylinder
208
426
308
28
Series 7300Rim Panic
Underwriters’ Laboratories Inc. Listed - Panic Hardware
For use with narrow, medium and wide stile Aluminum doors, Hollow Metal or Wood Doors
Non-handed, for LHRB or RHRB doors
Latch Bolt throw 5/8”
Dogging by Hex Key in Touch Bar
Outside Unlatching with standard Rim Cylinder
Standard Units for 36” and 48” door widths (cut bar to fit)
Can be used on 30” wide doors
Finishes Available: AL - ALUMINUM - Anodized extruded Aluminum with Baked Aluminum Painted Cover Caps DU - STOREFRONT BRONZE - Bronze Anodized extruded Aluminum with Baked Storefront Bronze Painted Cover Caps
Series 7100Concealed Vertical Rod
Underwriters’ Laboratories Inc. Listed - Panic Hardware
For use with narrow, medium and wide stile Aluminum doors
Non-handed, Field Reversible for LHRB or RHRB doors
Outside Unlatching and Dogging by Cylinder Key or Dogging by Hex Key in Touch Bar
Top Steel Toggle Latch and Bottom Steel Rod Latch Bolt
Units use Standard Mortise Cylinder with MS Type Cam and MP-6182 Cylinder Mounting Pad
Standard Units for 36” and 48” door widths (cut bar to fit) and up to 84” in height
Can be used on 30” wide doors
Finishes Available: AL - ALUMINUM - Anodized extruded Aluminum with Baked Aluminum Painted Cover Caps DU - STOREFRONT BRONZE - Bronze Anodized extruded Aluminum with Baked Storefront Bronze Painted Cover Caps
East: 800-225-6737 Fax: 615-885-0903
MP-6182Cylinder Mounting Pad
with Lock Ring
CZ-1001Mortise Cylinder
PH-6000 Pull Handle
MP-6000 Mounting Plate for Wood
or Metal Doors
RZ-1003 Rim Cylinder
ST-6312 Standard Surface
Roller Strike
29
Mechanical Locksets
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
ALP Series Grade 2 Cylindrical Locksets Available
ALS10Standard
ALS10R-Lever
R-Lever
Standard
R-Lever, I-Core
Standard, I-Core
Mechanical - ANSI GRADE 1Cylindrical Locksets
Grade 1 Cylindrical Locks
ANSI/BHMA Grade 1ANSI A250.13 compliantInternal clutch for vandal resistance 2-3/4” backset4 7/8” strike standard 2 3/4” strike optionalDull chrome finish standard
Functions Function Ordering Example: ALS10LF Passage ALS10 x _ _ ALS20LF Privacy LF - L Type w/Flat Rose ALS30LF Entrance RF- R Type with/Flate Rose ALS40LF Classroom LR- L Type with/Round Rose ALS50LF Store room RR- R Type with/Round Rose NOTE: Dull chrome finish standard
IDC ALS Series locksets are designed for commercial, industrial and institutional use, where dependable operation and longevity is required along with high resistance to vandalism and abuse. Applications include office buildings, government centers, factories, schools and hospitals and more. Internal clutch provides vandal resistance by permitting lever rotation without retracting latch when locked. Independent heavy duty springs provide effective lever return and support.
30
East: 800-225-6737 Fax: 615-885-0903
Electrified Locksets
Electra™ Pro Electrified Cylindrical LocksetsRequest to Exit output standard ANSI Grade 1 Dual 12/24 VDCFailsafe or failsecure operating modeClutch for vandal resistanceOptional I-CoreIDC cylinder with ‘C’ keywayADA compliant lever handlesUL Listed for 3Hr fire rated doorsEclipse or Galaxy lever
Functions Z7250 Failsafe, locked outside Z7252 Failsecure, locked outside UL CSFM MEA
Electra™ Mod Electrified Cylindrical LocksetsLocked on exterior only IDC electrified Schlage ND series 600mA/300mA @ 12/24VDCRex optionalCustomer or distributorsend Schlage lock to IDCfor modification
Functions S7250 Failsafe S7252 Failsecure
Options R Request-to-exit, SPDT UL CSFM MEA
31
7000-DG Pro Electrified Mortise LocksetsDrilling guide spans full door width for more accurate drilling Full width guide is adjustable several degrees up or down from hinge stile to lock stile to accommodate lock position.
Functions 7000-DG Door Core Drill Fixture with case 7000-DB1/4 1/4” 4 Ft. Drill Bit 7000-DB3/8 3/8” 4 Ft. Drill Bit
Standard
R-Lever
Key Cylinder - Optional“L” Lever with “Round” Rose
“R” Lever with “Flat” Rose
Mortise LocksetsGrade 1
Field reversible handing without disassemblyRetrofit most other brand locksets (consult factory)Internal clutch for vandal resistance One or two heavy duty spring cages as required per function
Functions Standard R-Lever Dull chrome finish standard M7801EU M7801GU Passage M7804EU M7804GU Office M7805EU M7805GU Classroom M7807EU M7807GU Store room M7809EU M7809GU Apartment entrance / vestibule M7813EU M7813GU Corridor / exit M7820EU M7820GU Entrance M7822EU M7822GU Privacy
IDC Heavy Duty Mortise Locks comply with American National Standard Institute requirement ANSI/ BHMA 156.13 Grade 1. All our locks are field reversible and re-quire only simple steps for changing the hand of lock for easy installation.
Mortise Locks with Escutcheon Trim Available.
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-221532
Schlage Best
PDQFalcon
Cal Royal
Marks
Arrow
Dorma
Sargent
Yale
Corbin Russwin
Mortise Locksets
Selectric®Pro Electrified Mortise LocksetsIDC quality standards ANSI Grade 1 Heavy Duty Replaces most lock brandsField selectable Failsafe or FailsecureField selectable function:locked outside only or both sidesField selectable 12/24VDC Field selectable handingSelect factory supplied IDC trim or Schlage trim provided by others UL Listed for 3Hr fire rated doors
Functions Z7830 Failsafe, locked both sides Z7832 Failsecure, locked both sides Z7850 Failsafe, locked outside Z7852 Failsecure, locked outside Z7835 Locked outside and/or inside Outside failsecure, inside failsafe
Options R Failsafe, locked both sides D Failsecure, locked both sides S Failsafe, locked outside UL CSFM MEA
Selectric® Mod Mortise Lock ElectrificationElectrification of Major Brands: Send the mechanical lock to IDC, and IDC will return the electrified lockset to the customer. To expedite delivery, IDC stocks major brands for electrification. Customer may then send mechanical locks to IDC for credit and replenishment of IDC stock. Field selectable 12/24VDCUL Listed for 3 hr fire rated doors
Functions 7830 Failsafe, locked both sides 7832 Failsecure, locked both sides 7850 Failsafe, locked outside 7852 Failsecure, locked outside
Options* R Request-to-exit, SPDT D Door Status, SPDT S Latched and Locked, SPDT L Latchbolt Status, SPDT *not available with all brands UL CSFM MEA
East: 800-225-6737 Fax: 615-885-0903 33
Field Upgrade & Service Without Removing From The Frame
E6200Full Featured Magnetic Lock1200 lb holding force
Retrofits Securitron and Locknetics 70 magnetic locks
Magnetic bond sensor standard
Door status standard
10ft (3.05m) jacketed, stranded conductor cable
Dual voltage 12/24VDC
Steel housing, US32/630
Single 1511V, 1571V & 1581
Double 1512V, 1572V & 1582
E-6200 Full Featured Magnetic Lock
1511V & 1512V1650lbs. Holding ForceANSI Grade 1
BHMA Certified Holding Force
12/24VDC Sensing Input 350mA@24VDC (single) 700mA@12VDC (single)
1511V (Single)
1512V (Double)
UL10C CSFM MEA UBC
ANSI Grade 1
BHMA Certified Holding Force
12/24VDC Sensing Input 125mA@24VDC (single) 250mA@12VDC (single)
Lower Power Consumption
1571V (Single)
1572V (Double)
UL10C CSFM MEA UBC
1581V & 1582V650lbs. Holding ForceANSI Grade 1
BHMA Certified Holding Force
12/24VDC Sensing Input 220mA@24VDC (single) 440mA@12VDC (single)
1581V (Single)
1582V (Double)
UL10C CSFM MEA UBC
1571V & 1572V Energy Saver1200lbs. Holding Force
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-221534
Interlocking Quick Mount Assembly
Single 1511V, 1571V & 1581
Hi/Shear EMLock®2000lbs. Holding Force
Static sensor activates lock only when door is aligned and at rest
Lateral & vertical alignment adj.
Sensing 12/24VDC input
Status sensors optional
1561-ITCM .875”-1.125” top channels
561-HTCM Up to 1.9375” top channels
1561-FTCM Mortise armature prep
UL10C CSFM MEA UBC Hi/Shear EMLock®
Monitoring and Timer Options Examples
D - Door position sensor 1511VD
B - Magnetic bond sensor 1511VB
T - Adjustable 1-30 sec. timer 1511VT
L - Bi-Color LED 1511VL
A - Anti-Tamper sensor 1511VA
Multiple option example 1511VDBT
See modular program pricing when ordering separately for field upgrades. Different part numbers and pricing may apply
TJ1V for 1511 and 1571
TJ2V for 1512 and 1572
TJ81V for 1581V
TJ82V for 1582V
Universal Top Jamb Kits
Universal Glass Door KitsCompatible with all lock models
Field adjustable for .5”, .625” and .75” glass doors
HDB1 For 1511, 1571, 1581
HDB2 For 1512, 1572, 1582
East: 800-225-6737 Fax: 615-885-0903 35
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
101-DE Exit Check® Delayed Egress Controller15 or 30 second exit delayBuilt-In 3 function keypadControl InputsBuilt-in annunciation Monitoring outputsOptional EMLock outputsChoice of mountingTrigger modesPower- up modesDisplay modes
101-DE Wall mount controller with keypad control and resetSpecify Lock: 1581DEV, 1571DEV, 1511DEV, 1575DEU, 1576DEU
Activated by door movement or sensebar 15 sec. unlock delay, 1 or 2 sec. nuisance delay Emergency release inputMode status outputsDual 12/24VDC operationNFPA, UBC, IBC, IFC, CBC compliantBOCA & Chicago compliant optionalDigital countdown displaySelectable voice or tone warning
1511SNAKV Single1511TNAKV Tandem
Exit Check® Delayed Egress Lock 1650lbs. Holding Force
15 sec exit delay, 1 sec nuisance delay Subdued alarm, two tones UBC, NFPA 101 NFPA 1. UFC, IBC, IFC, BOCA & Chicago code compliant Field selectable manual or auto power-up modes
1581SNDV NFPA compliant1581SBDV BOCA, Chicago compliant
Mini Exit Check® Delayed Egress 650lbs. Holding Force
Mechanical Switch BarSPDT Contact (2 contacts opt.)Power loop includedEpoxy kit optional for all glass door42 & 48” optionalPush To Exit sign includedCode compliant sign MSB550V 36” 628 AluminumMSB550Y 36” 335 Black Anodized500-GL Glass door kit & adhesive
UL CSFM
Sure Exit® Sense BarSensor technologyTri-failsafe, auto activated emergency releaseTwo SPDT outputs12/24VDC operationSpecial finishes and lengths availablePush To Exit sign included
PSB560V 36” AluminumPSB560Y 36” Black Anodized500-GL Glass door kit & adhesive UL CSFM
Exit SwitchesIlluminated green “PUSH TO EXIT” signMomentary switch buttonSPDT contactStainless steel finish
422U 1 Gang, 2” button423U 1 Gang, 1-60 sec timer, 2” button412NU Narrow, 1¾” button
Emergency Pull Station
Blue housing with easy to read activation instructions avoids confusion with red fire alarm stations. 2-SPDT 10 Amp Contacts; 1-SPDT for lock release and 1-SPDT auxiliary contact for remote monitoring, CCTV activation or alarm activation.
492 Pull station emergency door release 492GL4 Four replacement glass rods492BB Blue surface mount box
36
East: 800-225-6737 Fax: 615-885-0903
Request-to-Exit input1 main relay output150 PIN codes from 1-6 digitsRed/Green/Amber status indicatorsPanic CodeDisable keypadAnti-tamper keypad lockout12/24VAC/DC
917U Stainless SteelTR12 Plug-in 12VDC Power Supply
EntryCheck™ Digital Keypad
Request-to-Exit input2 Form C relay contacts480 PIN codes from 1-6 digitsTwo LED status indicatorsDoor sense inputDisable keypadAnti-tamper keypad lockout
928U Stainless Steel
EntryCheck™ Digital Keypad
Proximity & Pin Access Control System Key programmable for Standalone applicationsEntryCheck™ Access Control System PC Managed Network Up To 99 Openings
E5P Single Door Prox & PIN Reader & Controller 2nd reader input for egress or outdoor use
E5C Single Door 2 Reader Controller Only Choice of 6 prox and keypad readers
HID compatible cards & readers by others: 125 KHz; 26 to 40 bit Up to 3000 users E5P 4” read range Prox card only, Prox & PIN or PIN only entry Scheduled events and holidays Guard patrol function Audit trail, 3500 transaction buffer
HID1326-10 ProxCard II, 10 cards HID1326-25 ProxCard II, 25 cards HID1346-10 ProxKey II, 10 key fobs HID1346-20 ProxKey II, 20 key fobs
Optional Readers:
6005B E5PW K30W K40W 917W
Standalone Access Control E4KP EntryCheck™ Proximity & Access Control Reader
HID compatible cards by others: 125 KHz; 26 to 40 bit Up to 650 card users Up to 3” read range Weather resistant Remote relay module Prox only or Prox and PIN entry Forced entry alarm Duress outputCost-effective solution for access control and management User card can be registered/deleted in single or batch mode (with consecutive numbers)
HID1326-10 ProxCard II, 10 cards HID1326-25 ProxCard II, 25 cards HID1346-10 ProxKey II, 10 key fobs HID1346-20 ProxKey II, 20 key fobs
SPDT Contact (2 contacts opt.)Power loop includedEpoxy kit optional for all glass door42 & 48” optionalPush To Exit sign includedCode compliant sign MSB550V 36” 628 AluminumMSB550Y 36” 335 Black Anodized500-GL Glass door kit & adhesive
UL CSFM
37
www.intldoorclosers.com
West: 800-544-4422 Fax: 714-666-2215
7 field selectable modes: standard relay, timer, latch, or latch plus timer and 3 mantraps modes.
UR2A 2 Station Controller 4 inputs, 2 fused outputs 2 aux inputs, 2 aux outputs
UR4A 4 Station Controller 8 inputs, 4 fused outputs 4 aux inputs, 4 aux outputs
Power Supply Capacity 631/632RFA- 1 max. 634/636RF - 2 max
Programmable Door Controller 12/24 VDC voltage input4 N.O. inputs4 fused SPDT wet or dry outputs4 non-fused SPDT auxiliary outputsDim: 6” x 3”
CR4 Control Module
Power Supply Capacity 631RFA 2 max 634RF 4 max 636RF 4 max
4 Station Door Control Relay Module
1 Amp Class 2Access Control Power Supply
12/24VDC field selectableEmergency release input with manual reset capability1 Power limited switched output1 Power limited auxiliary outputBattery chargerInput, output & battery status LED
621B Power supply module 621P Power supply module, plug-in transformer 621PJ Power supply module, plug-in transformer & small enclosure
1 Amp Class 2 UL 294 Access Control Power Supply
12/24VDC field selectableEmergency release inputLow battery disconnectInput, output & battery status2 timers or door control modules with fused outputs (optional)
602RF 1 Amp Power Supply FB4 4 optional fused outputs Specify up to (2) FB4 for (8) outputs
38
East: 800-225-6737 Fax: 615-885-0903
2 Amp Class 2 Access Control Power Supply
12/24VDC field selectableLow battery disconnectInput, output & battery status Emergency release input with manual reset capability2 timers or door control modules with fused outputs (optional)
632RF 2 Amp power supply FB4 4 optional fused outputs
(1) 6A output & (3) 2A outputsField selectable 12/24VDCEmergency release input with field selectable manual reset Low battery disconnectInput, output & battery statusLarge cabinet: 16”Wx14”Hx6”D
636RF 6 Amp Power SupplyFB4 4 optional fused outputsSpecify up to (6) FB4 for (24) outputs
6 Amp Class 2 Access Control Power Supply
1.5 Amp Class 2 UL 294 Access Control Power Supply
12/24VDC field selectableEmergency release inputLow battery disconnectInput, output & battery status2 timers or door control modules with fused outputs (optional)
631RF 1.5 Amp power supply FB4 4 optional fused outputs
(1) 4A output & (2) 2A outputsField selectable 12/24VDCEmergency release input with field selectable manual reset Low battery disconnectInput, output & battery statusLarge cabinet: 16”Wx14”Hx6”D
634RF 4 Amp Power SupplyFB4 4 optional fused outputsSpecify up to (4) FB4 for (16) outputs
4 Amp Class 2 Access Control Power Supply
39
www.intldoorclosers.com
WEST: 4431 E. La Palma, Anaheim, CA 92807 Tel: (714) 666-0390 (800) 544-4422
Fax: (714) 666-2215 Email: [email protected]
EAST: 1920 Air Lane Drive, Nashville, TN 37210 Tel: (615) 885-7060 (800) 225-6737
Fax: (615) 885-0903 Email: [email protected]
www.intldoorclosers.com
Proud of our Past Focused on the Future
OHC ClosersSurface ClosersGate CloserDoor HardwareMiscellaneous HardwareStrikesDoor Holders, Stops & Flush BoltsThresholdsDoor SweepsAluminum Steel Pivots
Stainless Steel PivotsAluminum Geared HingesStainless Steel Pin & Barrel HingesButt Hinges & Power TransfersMechanical - Electrified Exit Devices & Escutcheon Trim Mechanical - LocksetsMechanical - Electrified Mortise LocksetsElectro-Magnetic Locks Access Controls