SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
A
www.cranepumps.com
1
General Information
6/15
INDEX
Industrial Pumps
and
Systems Catalog
For most current information, please see our online catalog at
www.cranepumps.com
© CRANE PUMPS & SYSTEMS, Inc. 2008 Printed in U.S.A
SECTION
PAGE
DATEB
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
This page intentionally left blank
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
1
www.cranepumps.com
1
General Information
1/06
BURKS CATALOG
Registered Trademarks
Burks Pumps is a registered trademark of Crane Pumps & Systems, Inc.Life-Lok is a registered trademark of Crane Pumps & Systems, Inc.MJ Jacketed Seal is a registered trademark of Crane Pumps & Systems, Inc.Noryl is a registered trademark of General Electric.Other brand and product names are trademarks or registered trademarks of their respective holders.
NOTICE
Performance and dimensional data presented in this catalog
are for planning purposes only and are subject to change
without notice. Certifi ed drawings available on request.
Consult your authorized Burks Pumps distributor for specifi c
details and the latest information, or call (937) 778-8947
3/08
SECTION
PAGE
DATE
2
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
Catalog Numbering SystemFor BURKS Industruial Pumps
The BURKS pump Catalog Number is composed of letters and numbers which designate four basic types of information: 1. Motor information 2. Pump series, or type 3. Pump size 4. Pump construction features
1. MOTOR INFORMATION
A. A letter prefi x identifi es other than the standard* motor voltage, Hz or enclosure, as follows: A = 115 Volts F = 550-575 Volts * “Standards” are: B = 200-208 Volts L = 50 Hz Voltage: 1 phase - 115/230V D = 380 Volts T = Totally Enclosed 3 phase - 230/460V E = 440-460 Volts X = Explosion Proof Hz: 60 Hz W = Washdown Enclosure: Open Drip Proof
B. The fi rst one, two, three or four numbers refer to motor horsepower, as follows: Single Phase Three Phase
2 = 1/4 HP ------ ------ 3 = 1/3 HP 33 = 1/3 HP 3100 = 10 HP 5 = 1/2 HP 35 = 1/2 HP 3150 = 15 HP 7 = 3/4 HP 37 = 3/4 HP 3200 = 20 HP 10 = 1 HP 310 = 1 HP 3250 = 25 HP 15 = 1½ HP 315 = 1½ HP 3300 = 30 HP 20 = 2 HP 320 = 2 HP 3400 = 40 HP 30 = 3 HP 330 = 3 HP 3500 = 50 HP 50 = 5 HP 350 = 5 HP 3600 = 60 HP 75 = 7½ HP 375 = 7½ HP 3750 = 75 HP
C. The number “4” immediately preceding the pump series designation identifi es the motor as being 1750RPM (4 pole).
2. PUMP SERIES, OR TYPE G = Close-Coupled End Suction Centrifugal GA = Close-Coupled End Suction Centrifugal (Tangental Discharge) GB = In-Line Centrifugal GV = Flange Mount Centrifugal (May be part of a factory assembled Condensate Return System.)
GNA = Base-Mounted Centrifugal w/small power frame GNB = Base-Mounted Centrifugal w/intermediate power frame GNC = Base-Mounted Centrifugal w/large power frame
WA = Close-Coupled Self-Priming Centrifugal WT = Close-Coupled Self-Priming Centrifugal GWT = Self-Priming Centrifugal Close-Coupled to Gas Engine WPT = Close-Coupled Self-Priming Centrifugal w/Viton seal and gasketing - sized for 1.62 S.G. fl uids WST = Close-Coupled Self-Priming Centrifugal w/explosion-proof motor - sized for .82 S.G. fl uids
CR = Small close-coupled turbine w/36 Frame open ventilated motor CT = Small close-coupled turbine CS = Large close-coupled turbine ET = Small base-mounted turbine ES = Large base-mounted turbine EC = Larger base-mounted turbine ED = Largest base-mounted turbine
FC = Column - or Pedestal-type sump pump FS = Submersible sump pump
8/08
1
35
2
GA
4
AB
3
5-1¼
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
3
www.cranepumps.com
1
General Information
1/06
Catalog Numbering SystemFor BURKS Industruial Pumps
3. PUMP SIZE The numbers following the pump series designation refer to pump size:
A. Centrifugals The fi rst number following the series designation refers to nominal impeller diameter. If it is followed by the letter “A”, this denotes a higher capacity version.
End-Suction, In-Line and Flange-Mount centrifugals have an additional number, after a hyphen, which indicates the pump discharge size. The suction port on end-suction pumps is always one pipe size larger than the discharge. GA5-1¼, GA6-1¼, GA7-1¼,GA6-1½, GA7-1½, GA6-2 G5-1¼, G6-1¼, G6-1½, G9-1½, G6-2, G7-2, G7A-2, G9-2, G7-2½, G9-2½, G9-3
B. Turbines The numbers following the series designation refer to impeller/raceway size. A larger number denotes a larger capacity pump. CR6/CT5, 6, 7/CS5 thru CS9 ET5, 6, 7/ES5 thru ES9/EC4 thru EC10/ED8 thru ED18.
4. PUMP CONSTRUCTION FEATURES The following suffi x letters are used to devote various construction features: AB = All Bronze construction AI = All Iron construction F = Flanged suction and discharge connections HT = High Temperature impeller (some turbine pumps) M = Mechanical Shaft Seal E = Mechanical Shaft Seal w/EPT rubber parts J = Mechanical Shaft Seal w/cooling Jacket V = Mechanical Shaft Seal w/Viton rubber parts SP = Special Order Pump. Non-standard feature(s) not covered by currently used Catalog Number designations (Serial Number must be furnished to properly identify any pump with this Catalog Number suffi x.) SS = Stainless Steel construction X = Built-in basket type strainer Two or more of these suffi x letters may be used on the same Catalog Number.
EXAMPLES
(1) (2) (3)
375G7A-2 375 G 7A-2
3 Phase 7½ HP Close-CoupledEnd-SuctionCentrifugal
7" Impeller Dia.
High Cap. Version
2" Discharge
(1) (2) (3) (4)
20WT5X 20 WT 5 X
1 Phase 2 HP Close-Coupled
Self-Priming
Centrifugal
5" Impeller Dia. Built-in
Basket-type
Strainer
(1) (2) (3) (4)
354CS7MV-AB 354 CS 7 MV-AB
3 Phase 1/2 HP
1725 RPM
Large
Close-Coupled
Turbine
Size 7
Impeller / Raceway
Mechanical Seal
w/Viton rubber parts
"All Bronze"
Construction
SECTION
PAGE
DATE4
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
This page intentionally left blank
Standard Terms and Conditions
OUR ACCEPTANCE OF YOUR ORDER IS EXPRESSLY CONDITIONED ON THE GENERAL TERMS AND CONDITIONS SET FORTH BELOW AND ALL TERMS STATED ON THE FACE OF THIS FORM. THE CONTRACT SHALL NOT INCLUDE ANY DEVIATING OR ADDITIONAL TERMS UNLESS EXPRESSLY AGREED TO IN WRITING AND SIGNED BY AN OFFICER OF OUR COMPANY.
PRICES: All prices are subject to change without notice and all shipments will be invoiced at the price in effect at the time of shipment, except when otherwise agreed to in writing by our authorized representative. Published prices are for products of our standard design and construction and any item not covered by the most recent published price list must be referred to us for special pricing. Prices do not include freight. Weights shown in price lists are approximate shipping weights. The amount of any applicable present or future tax or other government charge upon the production, sale, shipment or use of goods ordered or sold is not in the price and will be added to billing unless you provide us with an appropriate exemption certifi cate.
QUOTATIONS: Prices quoted by us are valid for 30 days from date of quotation unless we have otherwise specifi ed in writing. Clerical errors on quotations are subject to our correction and such errors will not be binding.
CANCELLATION AND REVISIONS: No purchase orders accepted and acknowledged by us may be cancelled or revised by you except with our prior written consent and upon payment of reasonable cancellation charges compensating us for all costs incurred in work done and material purchased. We reserve the right to determine what constitutes reasonable cancellation charges.
RETURN OF EQUIPMENT: No equipment shall be returned to us without fi rst obtaining a written Returned Goods Authorization and shipping instructions from us. The returner must prepay the charges in full for transportation to our factory. Credit allowed for new, undamaged equipment of current standard design will be a maximum of 80%; or less as determined by Customer Service; of the invoiced price or current billing price, whichever is less. The minimum value of returned product is $250 invoiced price or current billing price. Equipment which has been used, however slight, will not be accepted. Authorization will not be given for return of equipment, (1) which would, in our opinion, result in an excess in the amount of stock we normally carry, (2) not invoiced within the last 12 months, or (3) which is non-standard and manufactured specifi cally to a buyer’s specifi cations. For non-standard equipment not of our manufacture, the only credit allowed will be such credit as may be allowed by the manufacturer of such equipment. Equipment must be returned within 30 days of the issuance of the Returned Goods Authorization. No item with a net value of less than $35.00 will be authorized for return. Items not available for return are those that have a shelf life and hardware items. Unauthorized returns may be refused and\or returned freight collect.
CREDIT AND PAYMENT: Payment is due as noted on our invoice. Overdue accounts are subject to a service charge. All orders are subject to approval of our credit department and we may require full or partial payment in advance. Pro rata payments shall become due as shipments are made. If the shipments are delayed by you for any cause, payments shall become due from date on which we are prepared to make shipment and storage shall be at your risk and expense. If manufacture is delayed by you for any cause, a partial payment based upon the proportion of the order completed shall become due from the date on which we are notifi ed of the delay.
SECURITY INTEREST: We shall have a lien on all goods sold as security for payment on the invoice price, and upon request you shall provide and execute a fi nancing statement showing such lien.
DELIVERY: We will make reasonable effort to meet your delivery requirement provided you provide us, on a timely basis, all approvals, technical data, instructions and credit approval requirements needed for release of the shipment. However, all delivery and/or shipment dates are estimates only unless we have expressly guaranteed delivery of such dates in writing at your specifi c request. In no event shall we have any liability if delivery is delayed by strikes, labor disturbances, material shortages, plant calamities or disaster, acts of God, government actions, civil disturbance, the failure of any pre-supposed condition of the contract, withholding shipments due to credit clearance, or other interferences beyond our reasonable control, and the date of delivery shall be extended for a period of time equal to the time lost because of any such reason. Emergency Orders and Rush Orders: Contact the Sales Department for applicable handling fees.
SHIPPING: Unless you specify in writing and we acknowledge in writing, (A) goods will be boxed or crated as we may deem proper for protection against normal handling and for domestic shipment, (B) routing and manner of shipment will be at our discretion, and may be insured at your expense. An extra charge will be made for special handling. All shipments
© Crane Pumps & Systems, Inc. 2010
A Crane Co. Company
are F.O.B. point of manufacture. Delivery of goods to the initial carrier will constitute delivery to you and all goods will be shipped at your risk. A claim for loss or damage in transit must be entered with the carrier and prosecuted by you. Acceptance of material from a common carrier constitutes a waiver of any claims against us for delay, damage or loss.
FACTORY STORAGE: In the event Purchaser is unable to authorize or accept shipment upon noti! cation of Crane Pumps & Systems readiness to ship, equipment shall be placed in suitable storage by Crane Pumps & Systems. Storage charges and any charges for drayage, re-inspection by Quality Assurance, etc. will be for the account of the Purchaser.
GOVERNING LAW: It is understood and agreed that these Terms and Conditions of Sale shall be interpreted under and pursuant to the laws of the State of Ohio; you agree that any action at law or suit which is related to any contract of sale brought against us shall be ! led in a federal or state court located in the State of Ohio.
LIMITED WARRANTY: Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions. This warranty gives you speci! c legal rights, and there may also be other rights which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law (1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever shall be made against us, until the ultimate consumer, his successor, or assigns, noti! es us in writing of the defect, and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply. THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly stated otherwise, guarantees in the nature of performance speci! cations furnished in addition to the foregoing material and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for ! eld performance. Any additional guarantees, in the nature of performance speci! cations must be in writing and such writing must be signed by our authorized representative. Due to inaccuracies in ! eld testing if a con" ict arises between the results of ! eld testing conducted by or for user, and laboratory tests corrected for ! eld performance, the latter shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN. This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning (d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any modi! cation of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without our prior written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice and\or our speci! c recommendations. The purchaser is responsible for communication of all necessary information regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES, RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED BY ANY DEFECTS IN MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without our prior written approval.
If any litigation is commenced between the parties hereto for the enforcement of any rights hereunder, the successful party in subject litigation shall be entitled to receive from the unsuccessful party all costs incurred in connection therewith, including a reasonable amount for attorney�s fees.
YOUR ACCEPTANCE OF ANY GOODS SUPPLIED BY US, OR ON OUR BEHALF, SHALL, WITHOUT LIMITATION
CONSTITUTE ACCEPTANCE OF ALL TERMS AND CONDITIONS STATED ABOVE.
© Crane Pumps & Systems, Inc. 2010
420 Third Street 83 West Drive
Piqua, Ohio 45356 Brampton, Ont. Canada L6T 2J6
(937) 778-8947 (905) 457-6223
Fax (937) 773-7157 Fax (905) 457-2650
www.cranepumps.com
A Crane Co. Company
Limited 24 Month WarrantyCrane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship
under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained
in accordance with our instructions.This warranty gives you speci� c legal rights, and there may also be other rights
which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law
(1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same
duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever
shall be made against us, until the ultimate consumer, his successor, or assigns, noti� es us in writing of the defect,
and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply.
THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY
PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR
AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE
NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly
stated otherwise, guarantees in the nature of performance speci� cations furnished in addition to the foregoing material
and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for
� eld performance. Any additional guarantees, in the nature of performance speci� cations must be in writing and such
writing must be signed by our authorized representative. Due to inaccuracies in � eld testing if a con! ict arises between
the results of � eld testing conducted by or for user, and laboratory tests corrected for � eld performance, the latter
shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS
ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND
PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF
SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN.
This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning
(d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any
modi� cation of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor
cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without
our prior written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice
and\or our speci� c recommendations. The purchaser is responsible for communication of all necessary information
regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR
ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES,
RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST
PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES
ARE CAUSED BY ANY DEFECTS IN MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN
SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise,
without our prior written approval.
420 Third Street 83 West Drive
Piqua, Ohio 45356 Brampton, Ont. Canada L6T 2J6
(937) 778-8947 (905) 457-6223
Fax (937) 773-7157 Fax (905) 457-2650
www.cranepumps.com
RETURNED GOODS
RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.
CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.
Products Returned Must Be Cleaned, Sanitized,
Or Decontaminated As Necessary Prior To Shipment,
To Insure That Employees Will Not Be Exposed To Health
Hazards In Handling Said Material. All Applicable Laws
And Regulations Shall Apply.
IMPORTANT!
WARRANTY REGISTRATION
Your product is covered by the enclosed Warranty.To complete the Warranty Registration Form go to:
http://www.cranepumps.com/ProductRegistration/
If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor.
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
9
www.cranepumps.com
1
General Information
Pump Weights
1/06
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
SERIES: GA4-3/4 SERIES: GA5-1 SERIES: GA6-1-1/2
3GA4-3/4 1/3 37 3GA5-1 1/3 40 104GA6-1-1/2 1 70
5GA4-3/4 1/2 39 5GA5-1 1/2 42 310GA6-1-1/2 1 70
7GA4-3/4 3/4 42 7GA5-1 3/4 45 15GA6-1-1/2 1½ 75
10GA4-3/4 1 44 10GA5-1 1 47 20GA6-1-1/2 2 80
15GA4-3/4 1½ 48 15GA5-1 1½ 51 30GA6-1-1/2 3 95
33GA4-3/4 1/3 39 20GA5-1 2 58 50GA6-1-1/2 5 135
35GA4-3/4 1/2 40 33GA5-1 1/3 42 315GA-1-1/2 1½ 76
37GA4-3/4 3/4 41 35GA5-1 1/2 43 320GA6-1-1/2 2 81
310GA4-3/4 1 45 37GA5-1 3/4 44 330GA6-1-1/2 3 83
315GA4-3/4 1½ 49 310GA5-1 1 48 350GA6-1-1/2 5 110
SERIES: GA4-1 315GA5-1 1½ 52 375GA6-1-1/2 7½ 122
3GA4-1 1/3 38 320GA5-1 2 59 SERIES: GA6-2
5GA4-1 1/2 40 330GA5-1 3 60 104GA6-2 1 75
7GA4-1 3/4 43 SERIES: GA5-1-1/4 154GA6-2 1½ 78
10GA4-1 1 45 3GA5-1-1/4 1/3 40 310GA6-2 1 75
15GA4-1 1½ 59 5GA5-1-1/4 1/2 42 3154GA6-2 1½ 78
33GA4-1 1/3 40 7GA5-1-1/4 3/4 45 30GA6-2 3 100
35GA4-1 1/2 41 10GA5-1-1/4 1 47 50GA6-2 5 140
37GA4-1 3/4 42 15GA5-1-1/4 1½ 51 330GA6-2 3 88
310GA4-1 1 46 20GA5-1-1/4 2 58 350GA6-2 5 115
315GA4-1 1½ 50 33GA5-1-1/4 1/3 42 375GA6-2 7½ 128
SERIES: GA4-1-1/4 35GA5-1-1/4 1/2 43 SERIES: GA7-1-1/2
3GA4-1-1/4 1/3 39 37GA5-1-1/4 3/4 44 104GA7-1-1/2 1 82
5GA4-1-1/4 1/2 41 310GA5-1-1/4 1 48 154GA7-1-1/2 1½ 85
7GA4-1-1/4 3/4 44 315GA5-1-1/4 1½ 52 3104GA7-1-1/2 1 82
10GA4-1-1/4 1 46 320GA5-1-1/4 2 59 3154GA7-1-1/2 1½ 85
15GA4-1-1/4 1½ 50 330GA5-1-1/4 3 60 50GA7-1-1/2 5 146
33GA4-1-1/4 1/3 41 SERIES: GA6-1-1/4 75GA7-1-1/2 7½ 186
35GA4-1-1/4 1/2 42 10GA6-1-1/4 1 47 350GA7-1-1/2 5 121
37GA4-1-1/4 3/4 43 15GA6-1-1/4 1½ 51 375GA7-1-1/2 7½ 131
310GA4-1-1/4 1 47 20GA6-1-1/4 2 58 3100GA7-1-1/2 10 166
315GA4-1-1/4 1½ 51 30GA6-1-1/4 3 67 SERIES: G5-1-1/4
SERIES: GA4-1-1/2 310GA6-1-1/4 1 48 3G5-1-1/4 1/3 40
5GA4-1-1/2 1/2 36 315GA6-1-1/4 1½ 52 5G5-1-1/4 1/2 42
7GA4-1-1/2 3/4 39 320GA6-1-1/4 2 59 7G5-1-1/4 3/4 45
10GA4-1-1/2 1 41 330GA6-1-1/4 3 63 10G5-1-1/4 1 47
15GA4-1-1/2 1½ 45 SERIES: GA7-1-1/4 15G5-1-1/4 1½ 51
35GA4-1-1/2 1/2 36 30GA7-1-1/4 100 20G5-1-1/4 2 58
37GA4-1-1/2 3/4 39 50GA7-1-1/4 140 33G5-1-1/4 1/3 42
310GA4-1-1/2 1 41 330GA7-1-1/4 88 35G5-1-1/4 1/2 43
315GA4-1-1/2 1½ 45 350GA7-1-1/4 115 37G5-1-1/4 3/4 44
375GA7-1-1/4 128 310G5-1-1/4 1 48
G5-1-1/4 Continued on next page
SECTION
PAGE
DATE
10
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
1/06
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
SERIES: G5-1-1/4 SERIES: G7 SERIES: G9
315G5-1-1/4 1½ 52 204G7-2-1/2 2 163 3154G9-2 1½ 153
320G5-1-1/4 2 49 304G7-2-1/2 3 178 3204G9-2 2 168
330G5-1-1/4 3 60 3104G7-2 1 102 3304G9-2 3 183
SERIES: G6-1-1/4 3154G7-2 1½ 110 3504G9-2 5 215
10G6-1-1/4 1 55 3204G7-2 2 134 3304G9-2-1/2 3 210
15G6-1-1/4 1½ 55 3104G7A-2 1 102 3504G9-2-1/2 5 242
20G6-1-1/4 2 61 3154G7A-2 1½ 110 3754G9-2-1/2 7½ 264
30G6-1-1/4 3 70 3204G7A-2 2 134 3504G9-3F 5 254
310G6-1-1/4 1 52 3154G7-2-1/2 1½ 139 3754G9-3F 7½ 276
315G6-1-1/4 1½ 55 3204G7-2-1/2 2 163 31004G9-3F 10 300
320G6-1-1/4 2 63 3304G7-2-1/2 3 178 3504G9-4F 5 254
330G6-1-1/4 3 67 50G7-2 5 160 3754G9-4F 7½ 276
SERIES: G6 75G7-2 7½ 192 31004G9-4F 10 300
104G6-1-1/2 1 80 50G7A-2 5 160 3100G9A-1-1/2 10 191
104G6-2 1 80 75G7A-2 7½ 192 3150G9A-1-1/2 15 227
154G6-2 1½ 83 350G7-2 5 130 3200G9A-1-1/2 20 281
104G6-2-1/2 1 83 375G7-2 7½ 149 3200G9-2 20 305
154G6-2-1/2 1½ 91 3100G7-2 10 175 3250G9-2 25 331
204G6-2-1/2 2 115 3150G7-2 15 203 3300G9-2 30 403
3104G6-1-1/2 1 80 375G7A-2 7½ 149 3400G9-2 40 473
3104G6-2 1 80 3100G7A-2 10 175 3250G9-2-1/2 25 358
3154G6-2 1½ 83 3150G7A-2 15 203 3300G9-2-1/2 30 430
3104G6-2-1/2 1 83 3200G7A-2 20 271 3400G9-2-1/2 40 500
3154G6-2-1/2 1½ 91 3200G7-2-1/2 20 290 3500G9-2-1/2 50 530
3204G6-2-1/2 2 115 3250G7-2-1/2 25 305 3600G9-2-1/2 60 626
15G6-1-1/2 1½ 85 3300G7-2-1/2 30 293 3300G9-3F 30 442
20G6-1-1/2 2 98 SERIES: G9 3400G9-3F 40 512
30G6-1-1/2 3 155 104G9A-1-1/2 1 110 3500G9-3F 50 542
50G6-1-1/2 5 138 154G9A-1-1/2 1½ 120 SERIES: DF4-1-1/4
75G6-1-1/2 7½ 177 204G9A-1-1/2 2 144 3DF4-1-1/4 1/3 42
20G6-2 2 90 154G9-2 1½ 153 5DF4-1-1/4 1/2 42
30G6-2 3 95 204G9-2 2 158 7DF4-1-1/4 3/4 45
50G6-2 5 140 304G9-2 3 183 10DF4-1-1/4 1 47
75G6-2 7½ 180 504G9-2 5 215 33DF4-1-1/4 1/3 41
75G6-2-1/2 7½ 196 304G9-2-1/2 3 210 35DF4-1-1/4 1/2 43
SERIES: G7 504G9-2-1/2 5 242 37DF4-1-1/4 3/4 44
104G7-2 1 102 754G9-2-1/2 7½ 264 310DF4-1-1/4 1 48
154G7-2 1½ 110 504G9-3F 5 254
204G7-2 2 134 754G9-3F 7½ 275
104G7A-2 1 102 3104G9A-1-1/2 1 110
154G7A-2 1½ 110 3154G9A-1-1/2 1½ 120
204G7A-2 2 134 3204G9A-1-1/2 2 144
154G7-2-1/2 1½ 139 3304G9A-1-1/2 3 159
Continued next column....
Pump Weights
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
11
www.cranepumps.com
1
General Information
6/15
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
SERIES: DF6-2-1/2 SERIES: GV - 9 Gallon Receiver SERIES: GV6 - 14 Gallon Receiver
104DF6-2-1/2 1 83 3GV6-9 1/3 220 37GV6-14D 3/4 267
154DF6-2-1/2 1½ 91 5GV6-9 1/2 224 310GV6-14D 1 277
204DF6-2-1/2 2 115 7GV6-9 3/4 227 315GV6-14D 1½ 297
304DF6-2-1/2 3 130 10GV6-9 1 229 320GV6-14D 2 307
3104DF6-2-1/2 1 83 15GV6-9 1½ 239 330GV6-14D 3 313
31544DF6-2-1/2 1½ 91 20GV6-9 2 244 SERIES: GV6 - 20 Gallon Receiver
3204DF6-2-1/2 2 91 30GV6-9 3 247 3GV6-20 1/3 265
3304DF6-2-1/2 3 115 33GV6-9 1/3 220 5GV6-20 1/2 269
SERIES: GB 35GV6-9 1/2 224 7GV6-20 3/4 272
3GB5-1-1/2F 1/3 47 37GV6-9 3/4 227 10GV6-20 1 274
5GB5-1-1/2 1/2 53 310GV6-9 1 229 15GV6-20 1½ 284
7GB5-1-1/2F 3/4 53 315GV6-9 1½ 239 20GV6-20 2 289
10GB5-1-1/2F 1 58 320GV6-9 2 244 30GV6-20 3 292
15GB5-1-1/2F 1½ 60 330GV6-9 3 247 33GV6-20 1/3 265
20GB5-1-1/2 2 65 SERIES: GV6 - 14 Gallon Receiver 35GV6-20 1/2 269
33GB5-1-1/2F 1/3 47 3GV6-14 1/3 216 37GV6-20 3/4 273
35GB5-1-1/2F 1/2 53 5GV6-14 1/2 227 310GV6-20 1 275
37GB5-1-1/2F 3/4 53 7GV6-14 3/4 228 315GV6-20 1½ 285
310GB5-1-1/2F 1 58 10GV6-14 1 225 320GV6-20 2 290
315GB5-1-1/2F 1½ 60 15GV6-14 1½ 235 330GV6-20 3 293
320GB5-1-1/2F 2 65 20GV6-14 2 240 3GV6-20D 1/3 315
SERIES: GV6 30GV6-14 3 243 5GV6-20D 1/2 323
3GV6-1-1/4FC 1/3 43 33GV6-14 1/3 216 7GV6-20D 3/4 329
5GV6-1-1/4FC 1/2 47 35GV6-14 1/2 227 10GV6-20D 1 333
7GV6-1-1/4FC 3/4 50 37GV6-14 3/4 228 15GV6-20D 1½ 353
10GV6-1-1/4FC 1 52 310GV6-14 1 225 20GV6-20D 2 363
15GV6-1-1/4FC 1½ 62 315GV6-14 1½ 235 30GV6-20D 3 369
20GV6-1-1/4FC 2 67 320GV6-14 2 240 33GV6-20D 1/3 315
30GV6-1-1/4FC 3 70 330GV6-14 3 243 35GV6-20D 1/2 323
33GV6-1-1/4FC 1/3 43 3GV6-14D 1/3 259 37GV6-20D 3/4 329
35GV6-1-1/4FC 1/2 47 5GV6-14D 1/2 267 310GV6-20D 1 333
37GV6-1-1/4FC 3/4 50 7GV6-14D 3/4 267 315GV6-20D 1½ 353
310GV6-1-1/4FC 1 42 10GV6-14D 1 277 320GV6-20D 2 363
315GV6-1-1/4FC 1½ 62 15GV6-14D 1½ 297 330GV6-20D 3 369
320GV6-1-1/4FC 2 67 20GV6-14D 2 307
330GV6-1-1/4FC 3 70 30GV6-14D 3 313
33GV6-14D 1/3 259
35GV6-14D 1/2 267
Continued next column....
Pump Weights
SECTION
PAGE
DATE
12
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
1/06
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
SERIES: GV6 - 36 Gallon Receiver SERIES: GV6 - 23-SR Gallon Receiver
SERIES: GV6-36-SR Gallon Receiver
3GV6-36 1/3 417 3GV6-23-SR 1/3 233 320GV6-36-SR 2 289
5GV6-36 1/2 421 5GV6-23-SR 1/2 237 330GV6-36-SR 3 292
7GV6-36 3/4 424 7GV6-23-SR 3/4 240 3GV6-36D-SR 1/3 308
10GV6-36 1 426 10GV6-23-SR 1 242 5GV6-36D-SR 1/2 316
15GV6-36 1½ 436 15GV6-23-SR 1½ 252 7GV6-36D-SR 3/4 322
20GV6-36 2 441 20GV6-23-SR 2 257 10GV6-36D-SR 1 326
30GV6-36 3 444 30GV6-23-SR 3 260 15GV6-36D-SR 1½ 346
33GV6-36 1/3 417 33GV6-23-SR 1/3 233 20GV6-36D-SR 2 356
35GV6-36 1/2 421 35GV6-23-SR 1/2 237 30GV6-36D-SR 3 362
37GV6-36 3/4 424 37GV6-23-SR 3/4 240 33GV6-36D-SR 1/3 308
310GV6-36 1 426 310GV6-23-SR 1 242 35GV6-36D-SR 1/2 316
315GV6-36 1½ 436 215GV6-23-SR 1½ 252 37GV6-36D-SR 3/4 322
320GV6-36 2 441 320GV6-23-SR 2 257 310GV6-36D-SR 1 326
330GV6-36 3 444 330GV6-23-SR 3 260 315GV6-36D-SR 1½ 346
3GV6-36D 1/3 460 3GV6-23D-SR 1/3 276 320GV6-36D-SR 2 356
5GV6-36D 1/2 468 5GV6-23D-SR 1/2 284 330GV6-36-SR 3 362
7GV6-36D 3/4 474 7GV6-23D-SR 3/4 290 SERIES: GNA
10GV6-36D 1 478 10GV6-23D-SR 1 294 GNA5-1-1/4 --- 31
15GV6-36D 1½ 498 15GV6-23D-SR 1½ 314 GNA6-1-1/4 --- 35
20GV6-36D 2 508 20GV6-23D-SR 2 324 SERIES: GNB
30GV6-36D 3 514 30GV6-23D-SR 3 330 GNB6-1-1/2 --- 93
33GV6-36D 1/3 460 33GV6-23D-SR 1/3 276 GNB6-2 --- 95
35GV6-36D 1/2 468 35GV6-23D-SR 1/2 284 GNB6-2-1/2 --- 104
37GV6-36D 3/4 474 37GV6-23D-SR 3/4 290 GNB7-2 --- 103
310GV6-36D 1 478 310GV6-23D-SR 1 294 GNB7A-2 --- 104
315GV6-36D 1½ 498 315GV6-23D-SR 1½ 314 GNB9A-1-1/2 --- 113
320GV6-36D 2 508 320GV6-23D-SR 2 324 SERIES: GNC
330GV6-36D 3 514 330GV6-23D-SR 3 330 GNC7-2-1/2 --- 293
SERIES: GV6-36-SR Gallon Receiver
GNC9-2 --- 349
3GV6-36-SR 1/3 265 GNC9-2-1/2 --- 360
5GV6-36-SR 1/2 269 GNC9-3F --- 372
7GV6-36-SR 3/4 272 GNC9A-3F --- 372
10GV6-36-SR 1 274 SERIES: 4GNA & 4GNB
15GV6-36-SR 1½ 284 4GNA6-1-1/2 --- 80
20GV6-36-SR 2 289 4GNB7-2-1/2 --- 122
30GV6-36-SR 3 292 4GNB9-2 --- 135
33GV6-36-SR 1/3 265 4GNB9-2-1/2 --- 162
35GV6-36-SR 1/2 269 4GNB9-3F --- 174
37GV6-36-SR 3/4 272 4GNB9-4F --- 174
310GV6-36-SR 1 274
315GV6-36-SR 1½ 284
Continued on next column....
Pump Weights
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
13
www.cranepumps.com
1
General Information
1/06
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
SERIES: WG6-2 SERIES: WPT SERIES: WST
50WG6-2 5 168 A3WPT3A 1/3 37 X20WST5AX 2 105
75GW6-2 7½ 186 3WPT3A 1/3 37 X35WST5 1/2 75
350GW6-2 5 168 5WPT5 1/2 56 X37WST5 3/4 80
375WG6-2 7½ 186 7WPT5 3/4 61 X310WST5 1 80
3100WG6-2 10 215 10WPT5 1 62 X315WST5 1½ 80
15WPT5 1½ 64 X320WST5 2 80
SERIES: WA6 20WPT5 2 74 X320WST5A 2 80
10WA6 1 70 30WPT5 3 76 X35WST5X 1/2 100
15WA6 1½ 72 30WPT5A 3 76 X37WST5X 3/4 105
20WA6 2 78 5WPT5X 1/2 79 X310WST5X 1 105
30WA6 3 80 7WPT5X 3/4 85 X315WST5X 1½ 105
310WA6 1 70 10WPT5X 1 83 X320WST5X 2 105
315WA6 1½ 72 15WPT5X 1½ 89 X320WST5AX 2 105
320WA6 2 78 20WPT5X 2 98 SERIES: GWT
330WA6 3 80 30WPT5X 3 101 GWT5A 3 65
SERIES: WT 30WPT5AX 3 101 SERIES: CR
AWT3A 1/3 35 33WPT3A 1/3 39 A3CR6M 1/3 17
3WT3A 1/3 35 35WPT5 1/2 57 3CR6M 1/3 17
5WT5 1/2 60 37WPT5 3/4 62 SERIES: CT
7WT5 3/4 52 310WPT5 1 63 24CT6M 1/4 36
10WT5 1 65 315WPT5 1½ 65 24CT7M 1/4 36
15WT5 1½ 70 320WPT5 2 73 3CT5M 1/3 32
20WT5 2 76 330WPT5 3 74 3CT6M 1/3 32
20WT5A 3 76 330WPT5A 3 74 5CT5M 1/2 35
5WT5X 1/2 80 35WPT5X 1/2 82 5CT6M 1/2 35
7WT5X 3/4 82 37WPT5X 3/4 86 5CT7M 1/2 35
10WT5X 1 85 310WPT5X 1 85 5CT8M 1/2 35
15WT5X 1½ 95 315WPT5X 1½ 88 7CT5M 3/4 37
20WT5X 2 99 320WPT5X 2 94 7CT6M 3/4 37
20WT5AX 2 99 330WPT5X 3 95 7CT7M 3/4 37
33WT3A 1/3 35 330WPT5AX 3 95 7CT8M 3/4 Factory
35WT5 1/2 60 SERIES: WST 10CT8M 1 Factory
37WT5 3/4 62 X5WST5 1/2 75 33CT5M 1/3 35
310WT5 1 65 X7WST5 3/4 80 33CT6M 1/3 35
315WT5 1½ 70 X10WST5 1 80 35CT5M 1/2 37
320WT5 2 76 X15WST5 1½ 80 35CT6M 1/2 37
320WT5A 2 76 X20WST5 2 80 35CT7M 1/2 37
35WT5X 1/2 80 X20WST5A 2 80 37CT6M 3/4 38
37WT5X 3/4 82 X5WST5X 1/2 100 37CT7M 3/4 38
310WT5X 1 85 X7WST5X 3/4 104 35CT8M 1/2 Factory
315WT5X 1½ 90 X10WST5X 1 105 37CT8M 3/4 Factory
320WT5X 2 96 X15WST5X 1½ 105 310CT8M 1 Factory
320WT5AX 2 96 X20WST5X 2 105
Continued next column....
Pump Weights
SECTION
PAGE
DATE
14
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
8/06
CATALOGNUMBER
HP WTLBS
CATALOGNUMBER
HP WTLBS
SERIES: CT Continued SERIES: CS
L3CT5M 1/3 32 350CS8M 5 75
L3CT6M 1/3 32 350CS9M 5 75
L5CT5M 1/2 35 L20CS6M 2 65
L5CT6M 1/2 35 SERIES: ET
LCT7M 1/2 35 ET5M --- 20
L7CT6M 3/4 37 ET6M --- 20
L7CT7M 3/4 37 ET7M --- 20
L10CT7M 1 56 ET8M --- 20
L5CT8M 1/2 Factory SERIES: ES
L7CT8M 3/4 Factory ES5M --- 36
L10CT8M 1 Factory ES6M --- 36
SERIES: CS ES7M --- 36
34CS5M 1/3 52 ES8M --- 36
34CS6M 1/3 52 ES9M --- 36
34CS7M 1/3 52 SERIES: EC
54CS6M 1/2 55 EC4M --- 70
54CS7M 1/2 55 EC5M --- 70
54CS8M 1/2 55 EC6M --- 70
334CS5M 1/3 48 EC7M --- 70
334CS6M 1/3 48 EC8M --- 70
334CS7M 1/3 48 EC9M --- 70
354CS6M 1/2 51 EC10M --- 70
354CS7M 1/2 51 SERIES: ED
354CS8M 1/2 51 ED8M --- 115
10CS5M 1 56 ED9M --- 115
10CS6M 1 56 ED10M --- 115
15CS5M 1½ 60 ED11M --- 115
15CS6M 1½ 60 ED12M --- 115
15CS7M 1½ 60 ED14M --- 115
20CS6M 2 65See Page 9 for Motor Weights
20CS7M 2 65
20CS8M 2 65
310CS5M 1 56
310CS6M 1 56
315CS5M 1½ 60
315CS6M 1½ 60
315CS7M 1½ 60
320CS6M 2 65
320CS7M 2 65
320CS8M 2 65
330CS7M 3 72
330CS8M 3 72
330CS9M 3 72
Pump Weights
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
15
www.cranepumps.com
1
General Information
1/06
for Base Mounted Pumps
HPNEMA Frame WT
LBSNEMA Frame WT
LBSNEMA Frame WT
LBS
SINGLE PHASE SINGLE PHASE SINGLE PHASEOpen Drip Proof
60 Hz. - 1750 RPM - 115/230 VTotally Enclosed
60 Hz. - 1750 RPM - 115/230 VExplosion Proof
60 Hz. - 1750 RPM - 115/230 V
1/4 56 15 --- --- --- ---
1/3 56 16 56 23 56 23
1/2 56 19 56 26 56 26
3/4 56 24 56 33 56 33
1 143T 46 143T 47 143T 47
1½ 145T 54 143T 60 145T 60
2 182T 79 182T 65 182T 65
3 184T 90 184T 77 184T 77
5 213T 99 213T 99 213T 99
Open Drip Proof60 Hz. - 3500 RPM - 115/230 V
Totally Enclosed60 Hz. - 3500 RPM - 115/230 V
Explosion Proof60 Hz. - 3500 RPM - 115/230 V
1/3 56 16 56 23 56 23
1/2 56 16 56 26 56 26
3/4 56 24 56 33 56 33
1 56 31 56 33 56 333
1½ 142T 46 143T 39 143T ---
2 145T 54 145T 41 145T ---
3 182T 79 182T 73 182T ---
5 184T 90 184T 98 184T --
THREE PHASE THREE PHASE THREE PHASEOpen Drip Proof
60 Hz. - 1750 RPM - 230/460 VTotally Enclosed
60 Hz. - 1750 RPM - 230/460 VExplosion Proof
60 Hz. - 1750 RPM - 230/460 V
1/4 56 15 --- --- --- ---
1/3 56 15 56 19 56 19
1/2 56 16 56 25 56 25
3/4 56 21 56 27 56 27
1 143T 34 143T 39 143T 39
1½ 145T 42 145T 43 145T 43
2 145T 42 145T 47 145T 47
3 182T 71 182T 57 182T 57
5 184T 82 184T 66 184T 66
7½ 213T 124 213T 117 213T 117
10 215T 144 215T 139 215T 139
15 254T 185 254T 267 254T 267
Motor Weights
SECTION
PAGE
DATE
16
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
1/06
for Base Mounted Pumps
Motor Weights
HPNEMA Frame WT
LBSNEMA Frame WT
LBSNEMA Frame WT
LBS
THREE PHASE THREE PHASE THREE PHASEOpen Drip Proof
60 Hz. - 3500 RPM - 230/460 VTotally Enclosed
60 Hz. - 3500 RPM - 230/460 VExplosion Proof
60 Hz. - 3500 RPM - 230/460 V
1/3 56 15 56 20 56 20
1/2 56 16 56 22 56 22
3/4 56 16 56 22 56 22
1 56 24 56 26 56 26
1½ 143T 34 143T 40 143T 40
2 145T 42 145T 45 145T 45
3 145T 42 182T 54 182T 54
5 182T 65 184T 65 184T 65
7½ 184T 79 213T 109 213T 109
10 213T 109 215T 130 215T 130
15 215T 130 254T 260 254T 260
20 254T 194 256T 300 256T 300
25 256T 220 284TS 416 284TS 416
30 284TS 288 324TS 632 286TS 506
40 286TS 355 324TS 632 326TS 632
50 324TS 425 326TS 672 326TS 672
60 326TS 485 365TS 700 364TS 700
SECTION
PAGE
DATE
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
17
www.cranepumps.com
1
General Information
1/06
CATALOGNUMBER
DESCRIPTION WTLBS
CATALOGNUMBER
DESCRIPTION WTLBS
HORIZONTAL STEEL Receiver REPAIR KIT FOR CR SERIES PUMPS
07193 20 Gallon 90 22850-6 CR6M Pumps 5
07195 30 Gallon 120 22850-6MV 6MV Pumps 5
07149 60 Gallon 190 REPAIR KIT FOR CT, ET, CS & ES SERIES PUMPS
07189 100 Gallon 256 20158-5 CT5M & ET5M 6
08355 200 Gallon 365 20158-6 CT6M & ET6M 6
20158-7 CT7M & ET7M 6
20522-5 CS5M & ES5M 8
07323 Float Switch 7 20522-6 CS6M & ES6M 8
07994 Alternator 13 20522-7 CS7M & ES7M 8
07324 Make-up Valve - 1/2" 6 20522-8 CS8M & ES8M 8
07148 Make-up Valve - 3/4" 7 20522-9 CS9M & ES9M 8
07175 Water Gauge - 10" 2 IMPELLER & RACEWAY REPAIR KIT For EC & ED SERIES
07178 Water Gauge - 16" 3 21707-4 E16-E16M-EC4-EC4M 12
00234 Pressure Relief Valve - 1/2" 1 21707-5 E17-E17M-EC5-EC5M 12
01904 Pressure Relief Valve - 3/4" 2 21707-6 E18-E18M-EC6-EC6M 12
01905 Pressure Relief Valve - 3/4" 2 21707-7 E19-E19M-EC7-EC7M 12
01907 Pressure Relief Valve - 1" 2 21707-8 E20-E20M-EC8-EC8M 12
01908 Pressure Relief Valve - 1" 2 21707-9 E21-E21M-EC9-EC9M 12
01909 Pressure Relief Valve - 1" 2 21707-10 E22-E22M-EC10-EC10M 12
07182 Strainer - 1" 3 21710-8 E23-E23M-ED8-ED8M 22
07182A Strainer - 1" Brass 5 21710-9 E24-E24M-ED9-ED9M 22
07183 Strainer - 1½" 5 21710-10 E25-E25M-ED10-ED10M 22
07183A Strainer - 1½" Brass 7 21710-11 E26-E26M-ED11-ED11M 22
07184 Strainer - 2½" 8 21710-12 E27-E27M-ED12-ED12M 22
07184A Strainer - 2½" Brass 9 21710-14 E29-E29M-ED14-ED14M 22
08872 Compression Strainer - 1" 3 MECHANICAL SHAFT SEAL REPAIR KIT For ECM & EDM
09194 Compression Strainer - 1½" 5 21708 ECM Pumps 1
05465 Lint Strainer - 1½" 9 21711 EDM Pumps 1
07492 Spanner Wrench - 3/16" Pin 1 PACKING GLAND REPAIR KIT For EC & ED
07492A Spanner Wrench - 5/32" 1 21709 EC Pumps 1
21877A Touch-up Enamel - Blue --- 21712 ED Pumps 1
07172 Float Switch 10
07266 Pressure Regulator Valve - 1/2" 4
07267 Pressure Regulator Valve - 3/4" 4
23045 7" - For 9 Gallon Receiver 2
23046 8" - For 14 Gallon Receiver 2
23047 8¾" - For 23 Gallon Receiver 2
23048 11¾" - For 36 Gallon Receiver 2
Weights for Accessories
SECTION
PAGE
DATE18
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598A Crane Co. Company
www.cranepumps.com
1
General Information
This page intentionally left blank