8/12/2019 Installation Guide for AutoFEM Lite
1/122
2014 AutoFEM Software LLP
Installation Guide for AutoFEM Analysis Lite
Version 2.2
8/12/2019 Installation Guide for AutoFEM Lite
2/122
Contents
Installation Guide for AutoFEM Analysis Lite (English) 6
1. AutoFEM Analysis Lite Installation 6
1.1 Requirements to software
1.2 Unpacking of the installation package
1.3 Installation of software (the clients part)
1.4 Registration of AutoFEM Analysis in the installed AutoCADversion
1.5 Launching AutoCAD with installed AutoFEM Analysis
2. Uninstallation of AutoFEM Analysis 15
3. AutoFEM Analysis Lite Limitations 17
4. Frequently Asked Questions 18
Where can I get the support concerning AutoFEM?
Recommended computer parameters for efficient (professional)work with AutoFEM Analysis
What versions o f AutoCAD does AutoFEM Analysis 2.x work?
Does AutoFEM work with AutoCAD 2011?
Does AutoFEM Analysis work with AutoCAD Lite?
I'm working with another CAD system (Inventor,MechanicalDesktop, Solidworks). Can I use AutoFEM?
I have installed AutoFEM, but it seems, that Fema Tool does notwork. What may be wrong?
How do I install AutoFEM on AutoCAD 2007, 2008?
5. Tips&Tricks 20
Requirements for the three-dimensional model for finite elementanalysis
How can I apply a force (or pressure) to a certain area of thepart?
I have created a report on my study and I see a blank image oran error message. What is this?
6. How to buy AutoFEM Analysis? 28
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 29
1. Installation von AutoFEM Lite 29
1.1 Anforderungen an Software
8/12/2019 Installation Guide for AutoFEM Lite
3/122
Contents1.2 Auspacken des Installationspakets
1.3 Installation der Software (des Clients Teil)
1.4 Registrierung von AutoFEM in der installiertenAutoCAD-Version
1.5 Launching AutoCAD with installed AutoFEM Analysis_22. Deinstallation von AutoFEM Lite 38
3. AutoFEM Lite Einschrnkungen 40
4. Hufig gestellte Fragen 41
Wo bekomme ich die Untersttzung ber AutoFEM?
Empfohlene Computer-Parameter fr eine effiziente (Berufs-)Arbeit mit AutoFEM
Welche Versionen von AutoCAD funktioniert AutoFEM 2.x?
Funktioniert AutoFEM mit AutoCAD 2011?
Wird AutoFEM Lite mit AutoCAD Lite arbeiten?
Ich bin mit einem anderen CAD-System (Inventor, MechanicalDesktop, Solidworks) arbeiten. Kann ich verwenden AutoFEM?
Ich habe AutoFEM installiert, aber es scheint, dass Fema-Toolfunktioniert nicht. Was knnte falsch sein?
Wie installiere ich AutoFEM auf AutoCAD 2007, 2008?
5. Tips & Tricks 42Anforderungen an das 3D-Modell fr die Finite-Elemente-Analyse
Wie kann ich eine Kraft (oder Druck) auf einen bestimmtenBereich des Teils?
Ich habe einen Bericht von meiner Studie erstellt, und ich sehe einleeres Bild oder eine Fehlermeldung. Was ist das?
6. Wie kann ich AutoFEM Analysis kaufen? 51
Guide d'installation pour AutoFEM Lite (franais) 52
1. Installation de AutoFEM 52
1.1 Exigences au logiciel
1.2 Ouverture du paquet d'installation
1.3 Installation du logiciel (de la part du client)
1.4 Enregistrement d'AutoFEM dans la version installed'AutoCAD
1.5 Lancement d'AutoCAD avec l'analyse de AutoFEM install
2. La dsinstallation d'AutoFEM 62
3. AutoFEM Lite limitations 64
8/12/2019 Installation Guide for AutoFEM Lite
4/122
8/12/2019 Installation Guide for AutoFEM Lite
5/122
ContentsEstoy trabajando con otro sistema de CAD (Inventor, MechanicalDesktop, Solidworks). Puedo utilizar AutoFEM?
5. Consejos y trucos 90
Requisitos para el modelo slido 3D para el anlisis de elementosfinitos
Cmo puedo aplicar una fuerza (o presin) a un readeterminada de la pieza?
He creado un informe de mi estudio y veo una imagen en blancoo un mensaje de error. Qu es esto?
6. Cmo puedo comprar el AutoFEM Anlisis? 99
Guida all'installazione per AutoFEM (italiano) 100
1. Installazione di AutoFEM Lite 100
1.1 Requisiti per il software1.2 Disimballaggio del pacchetto di installazione
1.3 Installazione del software (parte del cliente)
1.4 Registrazione di AutoFEM nella versione di AutoCAD installata
1.5 Avvio di AutoCAD con AutoFEM installato
2. Disinstallazione di AutoFEM 109
3. Limitazioni di AutoFEM Lite 111
4. Domande Frequenti 112Quale verione di AutoCAD lavora con AutoFEM Analysis?
Quali sono i requisiti di sistema per operare con AutoFEMAnalysis?
Ho avviato AutoCAD dopo l'installazione di AutoFEM Analisys manon riesco a visualizzare il men di AutoFEM Analisys, cosasuccede?
Funziona AutoFEM su AutoCAD 2011?
AutoFEM Analisys funziona su AutoCAD versione Lite?5. Consigli e suggerimenti 112
Requisiti per l'analisi ad elementi finiti di modelli tridimensionali
Come posso applicare una forza (o pressione) per una certaarea della parte?
Ho creato un report sul mio studio e vedo un'immagine vuota oun messaggio di errore. Che cosa questo?
6. Come acquistare AutoFEM? 121
8/12/2019 Installation Guide for AutoFEM Lite
6/122
6 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 6
Installation Guidefor AutoFEM Analysis Lite (english)
Version 2.2
2014 AutoFEM Softw are LLP
8/12/2019 Installation Guide for AutoFEM Lite
7/122
7 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 7
1. AutoFEM Analysis Lite Installation
1.1 Requirements to software AutoFEM Analysis Lite is a plugin for AutoCAD (system of computer design) for operational systemWindows XP/Vista/7/8. AutoFEM Analysis Lite 2.x works with AutoCAD versions 2007, 2008, 2009, 2010,2012, 2013, 2014.
AutoFEM Analysis Lite 2.x does not work with AutoCAD versions for MAC OS.
1.2 Unpacking of the installation packageUnpack the installation package autofem-x64.zip or autofem-x86.zip. Make sure that you have unpackedthe distributive package of the same capacity that your installed AutoCAD has (x64 or x86). Theinstallation package contains the following folders and files:
Files of AutoFEM Analysis Lite distributive package for x64 (left) and x86 (right)
The folder x64 or x86 contains Microsoft service files, necessary for the work of software programs inthe operational environment Windows. If file Setup-x64.exe (or Setup-x86.exe) cannot be launched atyour computer, it is necessary to install the file from the folder redist2010 in advance.For AutoFEM Analysis 2.x the file from the folder redist2010 must be installed in the system.For AutoCAD versions 2007, 2008, and 2009, the file from the folder redist2005 must be installed in thesystem.For AutoCAD versions 2010 and 2012, the file from the folder redist2008 must be installed in the system.For AutoCAD versions 2013 and 2014, the file from the folder redist2010 must be installed in the system.These files can also be downloaded from the official website of Microsoft Corporation.
1.3 Installation of software (the clients part)For the installation to be a success, you must have the right to installing software programs on your computer. Actuate the file "Setup-x64.exe" (Setup-x86.exe). Select the language for the wizards work inthe dialog which appears and press OK. Then, perform the wizards options.
8/12/2019 Installation Guide for AutoFEM Lite
8/122
8 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 8
Selecting a language for installation
Installation of AutoFEM Analysis Lite Step 2
8/12/2019 Installation Guide for AutoFEM Lite
9/122
9 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 9
Installation of AutoFEM Analysis Lite Step 3
Installation of AutoFEM Analysis Lite Step 4
8/12/2019 Installation Guide for AutoFEM Lite
10/122
8/12/2019 Installation Guide for AutoFEM Lite
11/122
11 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 11
Installation of AutoFEM Analysis Lite final step
1.4 Registration of AutoFEM Analysis Lite in the installed AutoCAD versions After the successful copying of AutoFEM Analysis files, the special setup dialog will be actuated, whichprovides the plugin registration in the needed version of AutoCAD or launch of the software. To register
AutoFEM in AutoCAD, it is necessary to click inside the second column opposite to the AutoCADversions, in which you want to use AutoFEM Analysis Lite by default. If you want to immediately start AutoFEM Analysis Lite, click inside the first column and then click "Start AutoFEM Analysis " button. Theaccess to the utility is available anytime from the menu Start and folder AutoFEM Analysis 2.x |
AutoFEM Analysis 2.x .
8/12/2019 Installation Guide for AutoFEM Lite
12/122
12 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 12
Registration dialog of AutoFEM Analysis Lite in AutoCAD
Retrieval of FEMA Tool from the menu Windows XP/Vista/7
1.5 Launching AutoCAD with installed AutoFEM Analysis Lite After successful installation of the system and its registration in AutoCAD, activate AutoCAD in order tostart working with AutoFEM Analysis Lite. At the first run, the window of Lite Limitations will appear.
8/12/2019 Installation Guide for AutoFEM Lite
13/122
13 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 13
Window at the initial run of AutoCAD after installation of AutoFEM Analysis Lite
Note.In some cases, for the ribbon with AutoFEM Analysis commands to appear, it is necessary tomanually reset 3D Workspace of AutoCAD. To do this, use the AutoCAD command"WSCURRENT" with the option "3D Modeling".In the AutoCAD window which will open, the ribbon with commands of AutoFEM Analysis Lite mustappear, as it is shown in the figure. Access to AutoFEM Analysis commands is available also from therespective menu of AutoCAD.
AutoFEM Analysis commands in the menu and AutoCAD ribbon
8/12/2019 Installation Guide for AutoFEM Lite
14/122
14 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 14
3D Workspace of AutoCAD resetting
8/12/2019 Installation Guide for AutoFEM Lite
15/122
15 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 15
2. Uninstallation of AutoFEM Analysis LiteUninstallation of AutoFEM Analysis Lite is recommended to perform in the following order.
a) Run the utilityFema Tool to unregister AutoFEM Analysis Lite in AutoCAD and remove ticksstanding opposite to all AutoCAD versions. This step deletes from AutoCAD the menu and ribbonwith AutoFEM Analysis Lite commands. If it is not made before uninstalling AutoFEM from theoperational system, then AutoCAD will continue showing the AutoFEM Analysis Lite menu in spiteof the systems absence. (In this case, to restore initial menu of AutoCAD, their forced resettingwill be required with the help of the AutoCAD command CUI).
Retrieval of the utility FEMA Tool from the menuStart | AutoFEM Analysis Lite 2.x in the Windows XP/Vista/7 environment
To switch off loading AutoFEM Analysis Lite in AutoCAD, remove all ticksstanding opposite to all AutoCAD versions and press Apply
This step must be made for all accounts in Windows, where AutoFEM Analysis Lite has beenregistered.
b) Retrieve the deinstalllation command of AutoFEM Analysis Lite from the folder AutoFEM AnalysisLite 2.x in the menu Start or use the relevant command in the Section Install/uninstall programs atthe Control Panel of Windows.
8/12/2019 Installation Guide for AutoFEM Lite
16/122
16 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 16
Retrieval of the AutoFEM uninstall command from the menuStart | AutoFEM Analysis Lite 2.x in the Windows XP/Vista/7 environment
The system will be removed.
8/12/2019 Installation Guide for AutoFEM Lite
17/122
17 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 17
3. AutoFEM Analysis Lite limitationsLimitations of Static Analysis and Buckling Analysis are as follows: You can select only one solid body for your study. You have two types of mechanical loads for any study (force and pressure). There is a limited number of model entities for applying loads/restrictions. You can analyze only major results (displacements, stresses, deformations, etc.) of calculations. You can use only full restriction (immovable fixation).
Limitations of Frequency Analysis are as follows: You can select only one solid body for your study . You can find only natural frequency first. Forces applied to the design are not included in the calculation. You have no possibility solve not fixed (spatially free) system.
Limitations of Fatigue Analysis are as follows:
You can select only one solid body for your study . You can analyze only a single event Fatigue problem.
Limitations of Forced Harmonic Oscillation Analysis are as follows: You can select only one solid body for your study . You have two types of mechanical loads for any study (force and pressure). You cannot use the Mechanical Oscillator as a source of oscillations.
Limitations of Thermal Analysis are: You can select only one solid body for your study . You can use only two boundary conditions for thermal analysis that are temperature and convection.
There are no any limitations concerning the number of freedom degrees for all studies, reports, study controls, etc.You have fully workable FEA instrument for your purposes.
8/12/2019 Installation Guide for AutoFEM Lite
18/122
18 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 18
4. Frequently Asked Questions
Where can I get the support concerning AutoFEM?
If you encounter difficulties installing or using AutoFEM, the best way to try to resolve them is to go directly to our technical support email: [email protected]. Please, be clear in describing your problem and tell us theversion of Windows, AutoCAD and AutoFEM, that you are using. We strongly recommend you to immediatelycontact with us instead of searching with Google all questions, concerning AutoFEM installation and etc. It is moreeffective and gives the results.
Recommended computer parameters for efficient (professional) work with AutoFEMAnalysis
Mathematical modeling of physical phenomena belongs to the class of the resource-intensive problems that requireserious computational resources. That is why, for efficient use of the finite element modeling system it isrecommended to use the most powerful computers accessible to the user. Moreover, increase in the dimensionalityof the solved problem can be achieved by using 64-bit operating systems.
AutoFEM Analysis is available in two versions depending on the bit capacity of the Windows operating system:1. AutoFEM for Windows 32-bit. The distinctive feature of the 32-bit operating systems is the existence of physical bound on the maximum volume of addressed information (about 2 GB), which limits capabilities neededfor analysis of systems with large number of finite elements.2. AutoFEM for Windows 64-bit (Windows XP 64-bit, Windows 7 64-bit and etc.). This system works on theprocessors that support 64-bit instructions. Operating systems with digit capacity 64-bit allow the user to addresssignificantly larger volumes of information and solve the problems of higher dimensionality.Recommended computer parameters for efficient (professional) work with AutoFEM AnalysisProcessor with support of 64-bit instructions, Intel i5, i7 series
RAM 8 GB min, 32 GB recomendedOperating system Windows XP/7/8 64-bitSoftware AutoCAD x64, AutoFEM x64
What versions of AutoCAD does AutoFEM Analysis 2.x work?
The system of finite element analysis "AutoFEM Analysis 2.x" works with AutoCAD (x86) 2007, 2008, 2009, 2010,2012, 2013, 2014 for Windows based operational systems on 32-bit platform x86 and with AutoCAD x64 2008, 2009,2010, 2012, 2013, 2014 for Windows based operational systems on 64-bit platform.
Does AutoFEM work with AutoCAD 2011?
No, it doesn't. Only AutoCAD 2007-2010, 2012-2014 are fully supported.
Does AutoFEM Analysis Lite work with AutoCAD Lite?
No, it doesn't. AutoFEM Analysis and AutoFEM Analysis Lite can be used only with full version of AutoCAD becausethe 3D modelling workspace is necessary for finite-element analysis.
mailto:[email protected]8/12/2019 Installation Guide for AutoFEM Lite
19/122
19 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 19
I'm working with another CAD system (Inventor,Mechanical Desktop, Solidworks). Can Iuse AutoFEM?
AutoFEM Analysis works only inside AutoCAD's 3D environment, it does not work directly with Inventor, MechanicalDesktop, SolidWorks etc. However, if you have the possibility to use AutoCAD, you can export your 3D model fromCAD system into AutoCAD via SAT file format (ACIS exchange file format) and then you can try to carry out finite-element analysis of your model using AutoFEM.
I have installed AutoFEM, but it seems, that Fema Tool does not work. What may bewrong?
Sometimes, you should install the Microsoft Visual C++ 2010 SP1 Redistributable Package x86 or the MicrosoftVisual C++ 2010 SP1 Redistributable Package (x64) before AutoFEM installation.
How do I install AutoFEM on AutoCAD 2007, 2008?
Sometimes, when you use AutoCAD 2007 or AutoCAD 2008, you should installthe Microsoft Visual C++ 2005 SP1Redistributable Package x86 or the Microsoft Visual C++ 2005 SP1 Redistributable Package (x64) before AutoFEMinstallation.
http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/en-us/download/details.aspx?id=13523http://www.microsoft.com/en-us/download/details.aspx?id=13523http://www.microsoft.com/download/en/details.aspx?id=55828/12/2019 Installation Guide for AutoFEM Lite
20/122
20 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 20
5. Tips&Tricks
Requirements for Solid 3D Model for Finite Element Analysis
The quality and possibility of constructing a finite element mesh is strongly dependent on the quality of volume models, so when building 3D models imposed more stringent requirements than conventionalmodeling in AutoCAD. You should consider the following requirements to create three-dimensional modelsof your products in terms of the finite element analysis. Mutual or self-intersection bodies are not allowed. It is impossible to construct a finite element mesh for
intersecting bodies. Before you create a study you always should test your model on the intersectionsby special AutoCAD commandINTERFERE. This command shows intersections between bodies if theyare. One advice is how intersections may be removed from the assembly if intersecting bodies consistof the same material. You can use the command of AutoCAD: UNION and unite intersecting bodies in awhole body.
Using the AutoCAD's command INTERFERE for checking the model onentersections.
8/12/2019 Installation Guide for AutoFEM Lite
21/122
21 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 21
Correct 3D model has no intersections between its parts. The finite element mesh may be constructed.
Between the bodies must be no gap, except when there are no actual gaps between the bodies. Allbodies, which are included in a study, must have a contact by a face, or edge, or vertex, with any other body of the study. So in the study, a totally unengaged body should not exist as it is like freelyhovering in space.
Model w ith gap betw een its parts. Mes h may be constructed in som e cases , but calculation can be incorrect or impossible.
3D body should be closed volume. Finite element mesh can be constructed only for a limited volume. In AutoCAD one can create a solid 3D model which consists of multiple separate volumes. For instance
if you have extruded multiple profile (see at the picture). Meshing of the such 3D body is impossible. Sothe 3D solid which consists of multiple separate volumes is not allowed in the FEA study. If you havesuch 3D solid you need use the AutoCAD's command SOLIDEDIT|SEPARATE before creating the FEAstudy to separate the single solid on multiple independent volumes.
8/12/2019 Installation Guide for AutoFEM Lite
22/122
22 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 22
The 3D solid consists of multiple volumes .
That solid after using SOLIDEDIT|SEPARATE command.
It is recommended to avoid to do rounding, chamfering, holes and decorative elements, which are notimportant for the strength of design. They can complicate the construction of the finite element grid andincrease the dimension of the problem (time to find a solution). But items which are bearing influence onstrength of design, e.g., fillets, ribs, etc., must be present in the model.
The bodies, united in a block are treated as one solid body which is obtained using a Boolean union of all bodies in the block. The bodies in the block may intersect with each other. No gap should existbetween the bodies as this will generate an error of grid generation.
8/12/2019 Installation Guide for AutoFEM Lite
23/122
23 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 23
How can I apply a force (or pressure) to a certain area of the part?
Often the loads are applied at some area of the part which you want to study. Use the AutoCAD's commandIMPRINT to create an area of load applying on the facet of the 3D model. Firstly(before creating the study!) , youshoud draw the geometry, which describes the area of loading, using AutoCAD's drawing commands. Then useIMPRINT to create a new facet on the existing face of the 3D model. See the screen-shots, illustrating these steps,below.
Drawing the contour of load aplying
Use the command IMPRINT
8/12/2019 Installation Guide for AutoFEM Lite
24/122
24 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 24
Selecting the body
Selecting the contour
8/12/2019 Installation Guide for AutoFEM Lite
25/122
25 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 25
Deleting the contour
Creating the Study and applying the force
8/12/2019 Installation Guide for AutoFEM Lite
26/122
26 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 26
I have created a report on my study and I see a blank image or an error message. What isthis?
On default AutoFEM Study's report contains 3D image of the result saved in VRML format. To see and operate withthe VRML presentation of the result, you must install the special plug-in for your Web-browser. We use and test thisfunctionality of the AutoFEM report system using Cortona3D Vrml viewer which can be freely downloaded by thelink:http://www.cortona3d.com/install.aspx
Also you can turn off the creation of 3D Vrml-model of the result using a special check box in the dialog box of theReport settings.
Vrml viewer is not installed
http://www.cortona3d.com/install.aspx8/12/2019 Installation Guide for AutoFEM Lite
27/122
27 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 27
Vrml viewer is available
Dialog box of the Report settings
8/12/2019 Installation Guide for AutoFEM Lite
28/122
28 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 28
6. How to buy AutoFEM Analysis?There are two main ways to pay for the commercial version and get the licence key.
Way One. You can use services of registration companies RegNow (it is convenient for USA and other countries worldwide) or ShareIt! (it is most comfortable for European users). The major advantages of buying the licence via RegNow or ShareIt! : Variety of payment options . These companies accept different kinds of electronic payments, bank
cards as well as non-cash bank transfers. They also offer the buyer all necessary accountingdocuments (invoices, etc.), if you need them.
Fixed value . RegNow and ShareIt! provide licen?es for AutoFEM Analysis at the same cost whichis stated on our website. If you need a non-standard set of modules which is not available on theregistrars website, please write [email protected], and we will accept it as individual order.
Rate of purchase . If you pay via electronic transfer (e.g., PayPal) or from the credit card, then, as arule, the license key will be given to you by an email as soon as in few minutes after the payment ismade.
Security . The purchase via RegNow or ShareIt! is the safest way of obtaining the licence for AutoFEM Analysis, as you pay money to the mediator, who can be an independent arbitrator and, thus,guarantee that you necessarily get the licence key with the configuration you have ordered.
Way Two. You can pay the value of the licence directly to the account of our company (AutoFEMSoftware LLP). You only need to request it via email [email protected], and we will post you thebill. The order must state:
Name and registered address of your company; Name of the company leader; Name and contacts of a person who will solve technical problems; Strict configuration (set) of modules which you wish to buy and their number; and What additional accounting documentation you need.
After you pay our bill, we will send you the serial number and necessary documents.
mailto:[email protected]://www.shareit.com/product.html?cart=1&productid=300356897http://www.regnow.com/softsell/nph-softsell.cgi?ss_short_order=true&items=28256-18/12/2019 Installation Guide for AutoFEM Lite
29/122
29 AutoFEM Softwar e LLP www.auto femsoft.com
Installation Guide for AutoFEM Analysis Lite (English) 29
Installationsanleitungfr AutoFEM Analysis Lite (deutsch)
Version 2.2
2014 AutoFEM Softw are LLP
8/12/2019 Installation Guide for AutoFEM Lite
30/122
30 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 30
1. Installation von AutoFEM
1.1 Anforderungen an Software AutoFEM ist ein Plugin fr das AutoCAD System der automatischen Entwurf fr das BetriebssystemWindows XP/Vista/7/8. AutoFEM 2.x arbeitet mit den AutoCAD-Versionen 2007, 2008, 2009, 2010, 2012,2013, 2014.
AutoFEM 2.x funktioniert nicht mit den AutoCAD Versionen fr MAC OS.
1.2 Entpacken des InstallationspaketsEntpacken Sie autofem-x64.zip or autofem-x86.zip. Stellen Sie sicher, dass Sie dieVerteilungsgerechtigkeit Paket mit der gleichen Kapazitt, wie Ihre installierte AutoCAD Version (x64
oder x86), entpackt. Das Installationspaket enthlt die folgenden Ordner und Dateien:
Dateien von AutoFEM Verteilungsgerechtigkeit Paket fr x64 (links) und x86 (rechts
Der Ordner x64 oder x86 enthlt Microsoft Service-Dateien fr die Arbeit von Software-Programmen imWindows-Betriebssystem. Wenn die Datei Setup-x64.exe (oder-Setup-x86.exe) nicht auf IhremComputer gestartet werden knnen , ist es notwendig, die Datei aus dem Ordner redist2010 im Vorauszu installieren.Fr AutoCAD-Versionen 2007, 2008, und 2009, muss die Datei aus dem Ordner redist2005 im Systeminstalliert sein.
Fr AutoCAD-Versionen 2010 und 2012, muss die Datei aus dem Ordner redist2008 im Systeminstalliert sein.Fr AutoCAD-Versionen 2013 und 2014, muss die Datei aus dem Ordner redist2010 im Systeminstalliert sein.
Diese Dateien knnen auch von der offiziellen Webseite von Microsoft Corporation heruntergeladenwerden.
1.3 Die Installation der Software (des Clients Teil)Fr eine erfolgreiche Installation, mssen Sie das Recht haben, Software-Programmen auf IhremComputer zu installieren. Aktivieren Sie die Datei "Setup-x64.exe" (Setup-x86.exe). Whlen Sie dieSprache fr den Assistenten im Dialog, der angezeigt wird, und drcken Sie OK. Dann werden Siedurch den Assistenten gefhrt.
8/12/2019 Installation Guide for AutoFEM Lite
31/122
31 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 31
Auswhlen einer Sprache fr die Installation
Installation von AutoFEM - Schritt 2
8/12/2019 Installation Guide for AutoFEM Lite
32/122
32 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 32
Installation von AutoFEM - Schritt 3
Installation von AutoFEM - Schritt 4
8/12/2019 Installation Guide for AutoFEM Lite
33/122
33 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 33
Installation von AutoFEM - Schritt 5
Installation von AutoFEM - Schritt 6
1.4 Registrierung von AutoFEM in der installierten AutoCAD-
VersionNach dem erfolgreichen Kopieren der AutoFEM Dateien wird der spezielle Setup-Dialog geffnet, der das Plugin in die bentigte Version von AutoCAD eintrgt. Um sich zu registrieren AutoFEM in AutoCAD,ist es notwendig, innerhalb der zweiten Sule gegenber den AutoCAD-Versionen, in denen Sie
AutoFEM standardmig verwenden mchten, klicken Sie auf. Wenn Sie sofort starten AutoFEM
8/12/2019 Installation Guide for AutoFEM Lite
34/122
34 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 34
mchten, klicken Sie in der ersten Spalte und klicken Sie dann auf "Start AutoFEM Analysis ". Der Zugriff auf das Dienstprogramm ist jederzeit aus dem Men Start-und Ordner AutoFEM Analysis 2.x |
AutoFEM Analysis 2.x mglich.
Registrierung von AutoFEM in AutoCAD
"FEMA Tool" in dem Men Windows XP/Vista/7
1.5 Start von AutoCAD mit installiertem AutoFEMNach erfolgreicher Installation des Systems und seiner Registrierung in AutoCAD, aktivieren Sie
AutoCAD, um mit AutoFEM arbeiten zu knnen. Beim ersten Starten wird der Dialog erscheinen, der den Modus der Demo aktiviert und die Verwendung mit der Dauer von 15 Tagen oder die Lizenz zuaktivieren erlaubt. (Einzelheiten der Aktivierung einer lokalen Lizenz siehe 2.1)
8/12/2019 Installation Guide for AutoFEM Lite
35/122
35 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 35
Dialog im Erstlauf von AutoCAD nach der Installation von AutoFEMBeachten Sie.In einigen Fllen, fr die Leiste mit AutoFEM Befehle, ist es notwendig, den 3D Arbeitsplatz von
AutoCAD zurckzusetzen. Um dies zu tun, verwenden Sie den AutoCAD-Befehl "WSCURRENT"mit der Option "3D-Modellierung".Im Fenster, das AutoCAD ffnet, muss die Leiste mit Befehlen AutoFEM erscheinen, wie es in der
Abbildung dargestellt ist. Der Zugang zu den AutoFEM Befehlen gibt es auch aus dem jeweiligen Menvon AutoCAD.
8/12/2019 Installation Guide for AutoFEM Lite
36/122
36 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 36
AutoFEM Befehle im Men und AutoCAD Leiste
8/12/2019 Installation Guide for AutoFEM Lite
37/122
37 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 37
3D-Arbeitsbereich von AutoCAD Zurcksetzen
8/12/2019 Installation Guide for AutoFEM Lite
38/122
38 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 38
2. Deinstallation von AutoFEM LiteFr die Deinstallation von AutoFEM wird empfohlen, folgende Schritte durchzufhren:
a) Fhren Sie das Dienstprogramm Fema Tool AutoFEM aus, um in AutoCAD abmelden undentfernen Sie Hkchen gegenber allen AutoCAD Versionen. Dieser Schritt lscht das Men von
AutoCAD und die Leiste mit den AutoFEM Befehlen. Wenn dies nicht vor der Deinstallation von AutoFEM aus dem System gemacht wurde, dann wird auch weiterhin AutoCAD das AutoFEMMen anzeigen, trotz der Abwesenheit des Systems. (In diesem Fall das Startmen von
AutoCAD wiederherstellen, seine gezwungene Rckstellung mit Hilfe der AutoCAD-Befehl "CUI"ist erforderlich).
Ausfhren des Dienstprogramms "FEMA Tool" aus dem MenStart | AutoFEM Analysis 2.x in der Windows XP/Vista/7 Umgebung
Zum Ausschalten von AutoFEM aus AutoCAD, entfernen Sie alle Hkchen gegenber allen AutoCAD Versionen unddrcken Sie auf "Apply"
Dieser Schritt muss fr alle Benutzerkonten in Windows, wo AutoFEM registriert wurde,vorgenommen werden.
b) Rufen Sie "Deinstalllation von AutoFEM" aus dem Ordner AutoFEM 2.x im Startmen auf oder benutzen Sie den entsprechenden Befehl im Abschnitt Installieren/Deinstallieren von Programmen inder Systemsteuerung von Windows.
8/12/2019 Installation Guide for AutoFEM Lite
39/122
39 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 39
Abrufen der AutoFEM Deinstallationsbefehls aus dem MenStart | AutoFEM Analysis 2.x in der Windows XP/Vista/7 Umgebung
Das System wird entfernt.
8/12/2019 Installation Guide for AutoFEM Lite
40/122
40 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 40
3. AutoFEM Lite EinschrnkungenDie Einschrnkungen der Statischen Analyse und Knickanalyse sind wie folgt: Sie knnen einen festen Krper nur fr eine Studie whlen. Sie haben nur zwei Arten von mechanischen Belastungen fr jede Studie (Kraft und Druck). Es besteht eine Begrenzung der Menge der Einheiten des Modells fr die Anwendung . Nur die wichtigsten Ergebnisse (Resultate der Verschiebungen, Spannungen, Verformungen usw.) werden
analysiert.
Die Einschrnkungen der Frequenz-Analyse s ind folgende: Sie knnen einen festen Krper nur fr eine Studie whlen. Sie knnen nur die erste Eigenfrequenz berechnen. Die am Design angebrachten Krfte sind von der Berechnung ausgeschlossen. Sie haben keine Mglichkeit,im Raum freie Systeme zu berechnen.
Die Einschrnkungen der Ermdungsanalyse s ind folgende: Sie knnen einen festen Krper nur fr eine Studie whlen. Sie knnen nur ein einzelnes Ereignis der Ermdungsstudie analysieren.
Die Einschrnkungen von Erzwungene Harmonikale Oszillation Analyse sind folgende: Sie knnen einen festen Krper nur fr eine Studie whlen. Sie haben nur zwei Arten von mechanischen Belastungen fr jede Studie (Kraft und Druck). Sie knnen den mechanischen Oszillators nicht als eine Quelle der Schwingungen whlen.
Die Einschrnkungen der Thermischen Analyse sind folgende: Sie knnen fr die thermische Analyse nur zwei Randbedingungen - Temperatur und Konvektion nutzen. Sie knnen einen festen Krper nur fr eine Studie whlen.
Es gibt keine Einschrnkungen bezglich der Anzahl der Freiheitsgrade fr alle Studien, Berichte, Studien-
Steuerungen usw.Sie haben ein voll funktionierendes FEA Instrument zu ihrer Verfgung.
8/12/2019 Installation Guide for AutoFEM Lite
41/122
41 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 41
3. Hufig gestellte Fragen
Wo bekomme ich die Untersttzung ber AutoFEM?
Wenn Sie Schwierigkeiten bei der Installation oder Verwendung AutoFEM begegnen, ist der beste Weg,um zu versuchen, sie zu lsen, um direkt zu unserem technischen Support per E-Mail:[email protected]. Bitte, klar in der Beschreibung Ihres Problems und uns die Version vonWindows, AutoCAD und AutoFEM, dass Sie verwenden. Wir empfehlen Ihnen dringend, sofort mit unsVerbindung treten, anstatt die Suche mit Google alle Fragen bezglich der Installation und AutoFEM usw.Es ist effektiver und gibt die Ergebnisse an.
Empfohlene Computer-Parameter fr eine effiziente (Berufs-) Arbeit mit AutoFEM
Die mathematische Modellierung von physikalischen Phnomenen gehrt zu denressourcenintensivsten Probleme die groe Rechenkapazitten erfordern. Deshalb ist fr deneffizienten Einsatz der Finite-Elemente-Modellierung empfohlen, so leistungsfhige Computer wie mglich zu verwenden. Auerdem kann die Erhhung der Dimensionalitt eines Problemsgelst durch Verwendung von 64-Bit-Betriebssystemen erreicht werden.
AutoFEM ist in zwei Versionen erhltlich je nach Version des Windows-Betriebssystems:1. AutoFEM fr Windows 32-Bit ( das Standard Windows zum Beispiel fr Computer mit
Pentium III oder IV). Die Besonderheit der 32-Bit-Betriebssystemen ist die Existenz der physischen Begrenzung auf das maximale Volumen der adressierten Informationen(ungefhr 2 GB), die Mglichkeiten fr die Analyse von Studien mit einer groen Anzahl vonFinite-Elemente ist begrenzt.
2. AutoFEM fr Windows 64-Bit (Windows XP 64-bit, Windows Vista 64-Bit etc.). DiesesSystem funktioniert auf den Prozessoren, die 64-Bit-Befehle (z. B. Intel Pentium D, IntelCore2Duo, AMD 64 und andere) untersttzen. Betriebssysteme mit 64-Bit-Kapazitterlauben dem Benutzer deutlich grere Mengen an Informationen anzusprechen undStudien von viel hherer Dimensionalitt zu lsen.
Technische Voraussetzungen fr eine effektive (professionelle) Arbeit mitAutoFEMProzessor Mit 64-bit Untersttzung, Intel i7, i5Festplattenspeicher (fr dieSpeicherung vonBerechnungsergebnisse)
80 GB und mehr
RAM 8 GB min, 32 GB empfohlenBetriebssystem Windows 64-bit (Windows XP, Windows Vista,
Windows 7)Software AutoCAD x64, AutoFEM x64
Welche Versionen von AutoCAD funktioniert AutoFEM 2.x?
Das System von Finite-Elemente-Analyse "AutoFEM 2.x" arbeitet mit AutoCAD (x86) 2007, 2008, 2009,2010, 2012, 2013, 2014 Windows-basierte Betriebssysteme auf 32-Bit-Plattform und AutoCADx642009, 2010, 2012, 2013, 2014 fr Windows-basierte Betriebssysteme auf 64-bit-Plattform.
mailto:[email protected]8/12/2019 Installation Guide for AutoFEM Lite
42/122
42 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 42
Funktioniert AutoFEM mit AutoCAD 2011?Nein, tut es nicht. Nur AutoCAD 2007-2010, 2012-2014 werden voll untersttzt.
Wird AutoFEM Lite mit AutoCAD Lite arbeiten?
Nein, tut es nicht. AutoFEM und AutoFEM Lite kann nur mit der Vollversion von AutoCAD verwendetwerden, da die 3D-Modellierung Arbeitsplatz ist notwendig fr die Finite-Elemente-Analyse.
Ich bin mit einem anderen CAD-System (Inventor, Mechanical Desktop, Solidworks)arbeiten. Kann ich verwenden AutoFEM?
AutoFEM funktioniert nur in 3D-Umgebung von AutoCAD, es arbeitet nicht direkt mit Inventor, MechanicalDesktop, SolidWorks etc. Allerdings knnen Sie Ihr 3D-Modell aus CAD-System AutoCAD exportieren inber SAT-Datei-Format (ACIS Austausch Dateiformat) und dann knnen Sie versuchen zur Durchfhrung von Finite-Elemente-Analyse des Modells mit AutoFEM.
Ich habe AutoFEM installiert, aber es scheint, dass Fema-Tool funktioniert nicht. Wasknnte falsch sein?
Manchmal, sollten Sie die Installation von Microsoft Visual C++ 2010 SP1 Redistributable Package x86or Microsoft Visual C++ 2010 SP1 Redistributable Package (x64) bevor AutoFEM Installation.
Wie installiere ich AutoFEM auf AutoCAD 2007, 2008?
Manchmal, sollten Sie die Installationthe Microsoft Visual C++ 2005 SP1 Redistributable Package x86or the Microsoft Visual C++ 2005 SP1 Redistributable Package (x64) bevor AutoFEM Installation.
4. Tips & Tricks
Anforderungen an das 3D-Modell fr die Finite-Elemente-Analyse
Die Qualitt und die Mglichkeit des Baus eines Finite-Elemente-Netzes ist stark abhngig von der Qualitt der Modelle, so gibt es beim beim Bau von 3D-Modellen strengere Anforderungen als bei der herkmmlichen Modellierung in AutoCAD. Sie sollten die folgenden Anforderungen beachten, umdreidimensionale Modelle Ihrer Produkte mit dem Ziel der Finite-Elemente-Analyse erstellen. Gegenseitige oder Selbst-Kreuzungen von Krpern sind nicht erlaubt. Es ist unmglich ein Finite-
Elemente-Netz von sich schneidenden Krper zu konstruieren. Bevor Sie eine Studie erstellen solltenSie immer Ihr Modell auf Schnittstellen testen, indem Sie die spezielle AutoCAD-Funktion _ INTERFERE
nutzen. Dieser Befehl zeigt Schnittstellen zwischen Krper. Ein Rat, wie Schnittpunkte entfernenknnen, wenn sich schneidenden Krper aus dem gleichen Material bestehen: Sie knnen mit demBefehl von AutoCAD: _ UNION die sich kreuzenden Stellen eines ganzen Krper verbinden.
http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/en-us/download/details.aspx?id=13523http://www.microsoft.com/en-us/download/details.aspx?id=83288/12/2019 Installation Guide for AutoFEM Lite
43/122
43 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 43
Mit dem AutoCAD-Befehl INTERFERE kann das Modell berpr ft w erden. Es gibt vielebers chneidungen. Die Erste llung einer Finite-Element-Studie ist unmglich.
Ein korrek tes 3D-Modell hat keine Schnittpunkte zw ischen se iner Te ile. Das Finite-Eleme nte-Netz kannaufgebaut w erden.
Zwischen den Krpern darf kein Spalt sein, es sei denn, es gibt keine tatschliche Lcken zwischen den Krpern. Alle Krper, die in einer Studie enthalten sind, mssen einen Kontakt durch eine Flche, Kante oder Ecke miteinem anderen Krper der Studie haben. So sollte in der Studie kein vllig "frei schwebender" Krper im Raumexistieren.
8/12/2019 Installation Guide for AutoFEM Lite
44/122
44 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 44
Ein Modell m it Spalt zwischen seinen Te ilen. Das Netz kann in einigen Fllen generier t, aber die Berechnungkann falsch sein oder nicht durchgefhrt werden.
3D-Krper muss ein geschlossenes Volumen sein. Das Finite-Elemente-Netz kann nur fr ein begrenztes Volumengebaut werden.
In AutoCAD kann man ein 3D-Modell, das aus mehreren Volumen besteht erstellen. Zum Beispiel, wennSie mehrere extrudierte Profile (siehe Bild) haben. Die Vernetzung dieser 3D-Krper ist unmglich unddarum ist das 3D-Model, da es aus mehreren getrennten Teilen besteht, nicht in die FEA Studie erlaubt.Wenn Sie ein solches 3D-Modell haben, machen Sie Gebrauch des AutoCAD-Befehls SOLIDEDIT|SEPARATE vor der Erstellung der FEA-Studie, um das einzige Objekt auf mehreren unabhngigeVolumen zu trennen.
8/12/2019 Installation Guide for AutoFEM Lite
45/122
45 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 45
Die 3D-Objekt bes teht aus mehr eren Volum en. Ansicht nach Verw endung des Befehls SOLIDEDIT|SEPARATE Es wird empfohlen, Rundungen, Lcher und dekorative Elemente, die nichts mit der Strke des Design zu tun
haben zu vermeiden. Sie knnen den Bau des Finite-Elemente-Netzes erschweren und erhhen die Dimension desProblems (erhhte Berechnungszeit). Aber Teile, die Einfluss auf die Strke der Konstruktion haben, mssenunbedingt im Modell vorhanden sein.
Die in einem Block vereinten Krper werden als solides Objekt, welches unter Verwendung einesBooleanischen Verbindung aller Stellen in einen Block behandelt wird. Die Krper in dem Block knnensich untereinander schneiden. Darf jedoch kein Spalt zwischen den Krpern bestehen, da dies einenFehler in der Netz-Generierung erzeugen.
Wie kann ich eine Kraft (oder Druck) auf einen bestimmten Bereich des Teils?
Oft werden die Lasten an einem gewissen Bereich des Teils aufgebracht. Verwenden Sie den AutoCAD-BefehlIMPRINT, um einen Bereich der Anwendung der Last auf der Facette des 3D-Modells zu erstellen. Erstens (vor der Erstellung der Studie! ), Mssen Sie ziehen die Geometrie der Flche des Ladens, mit AutoCAD-ZeichnungBefehle. Dann nutzen Sie IMPRINT, um eine neue Facette auf der bestehenden Flche des 3D-Modell zu erstellen.Siehe die Screen-Shots, veranschaulicht diese Schritte, unten.
8/12/2019 Installation Guide for AutoFEM Lite
46/122
46 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 46
Zeichnen Sie die Kontur Lastbeaufschlagungsblock
Verwenden Sie den Befehl _IMPRINT
8/12/2019 Installation Guide for AutoFEM Lite
47/122
47 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 47
Whlen Sie den Krper
Whlen Sie die Kontur
8/12/2019 Installation Guide for AutoFEM Lite
48/122
48 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 48
Lschen Sie die Kontur
Erstellen Sie die Studie und wenden Sie die Kraft
Ich habe einen Bericht von meiner Studie erstellt, und ich sehe ein leeres Bild oder eineFehlermeldung. Was ist das?
Bericht enthlt das 3D-Bild des Ergebnisses in VRML-Format gespeichert. Um zu sehen, und arbeiten mit der VRMLPrsentation des Ergebnisses, mssen Sie die speziellen Plug-In fr Ihren Web-Browser. Wir verwenden Cortona3DVRML-Viewer, die frei durch den Link heruntergeladen werden:http://www.cortona3d.com/install.aspx
http://www.cortona3d.com/install.aspx8/12/2019 Installation Guide for AutoFEM Lite
49/122
49 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 49
Auch Sie knnen ausschalten der Erstellung von 3D-VRML-Modell des Ergebnisses mit einem speziellenKontrollkstchen im Dialogfenster des Berichts Einstellungen.
VRML-Viewer ist nicht installiert
8/12/2019 Installation Guide for AutoFEM Lite
50/122
50 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 50
VRML-Viewer ist verfgbar
Dialog der Report-Einstellungen
8/12/2019 Installation Guide for AutoFEM Lite
51/122
51 AutoFEM Softwar e LLP www.auto femsoft.com
Installationsanleitung fr AutoFEM Analysis Lite (deutsch) 51
5. Wie kann ich AutoFEM Analysis kaufen?
Es gibt zwei Arten, die kommerzielle Version zu bezahlen und den Lizenzschlssel zu bekommen.Erste Weise. Sie knnen sich an die registrierenden Firmen RegNow (passend fr die USA und andereLnder in der ganzen Welt) oder ShareIt! (mehr passend fr europische Anwender) wenden. DieHauptvorteile des Kaufes der Lizenz per RegNow oder ShareIt! sind folgende: Beliebige Bezahlungweise. Diese Firmen nehmen verschiedene Arten der elektronischen
Zahlungen, Kreditkarten sowie bargeldlose Bankanweisungen an. Sie gewhren auch dem Kundenalle notwendigen Buchhaltungsunterlagen (Invoice usw.).
Fixierter Preis. RegNow und ShareIt! liefern die Lizenzen AutoFEM Analysis mit demselben Preis,der auf unserer Homepage angegeben ist. Wenn Sie einen ungewhnlichen Satz von Modulenbentigen, den es auf den Homepages der registrierenden Firmen nicht gibt, schreiben Sie bitte unsan die Adresse [email protected], Diese E-Mail-Adresse ist gegen Spambots geschtzt! Siemssen JavaScript aktivieren, damit Sie sie sehen es knnen. Wir werden die individuelle Bestellungfr Sie vornehmen.
Schneller Kauf. Wenn Sie elektronische Zahlungsmittelberweisung ttigen (z.B. PayPal) oder mitKreditkarte bezahlen, bekommt man in der Regel den Lizenzschlssel per E-Mail in einigen Minutennach der Bezahlung.
Sicherheit. Der Kauf mit RegNow oder ShareIt! ist die sicherste Weise der AutoFEM AnalysisLizenzerwerbung, weil Sie das Geld dem Vermittler zahlen, der als unabhngiger Schiedsrichter auftreten kann, und garantiert auf diese Art, dass Sie den Lizenzschlssel in der von Ihnen bestelltenKonfiguration bekommen.
Zweite Weise. Sie knnen die Lizenz direkt bei uns kaufen (AutoFEM Software LLP). Dazu brauchen
wir die Anfrage per E-Mail an [email protected] Diese E-Mail-Adresse ist gegen Spambotsgeschtzt! Sie mssen JavaScript aktivieren, damit Sie sie sehen knnen. Darauf folgend werden wir eine Rechnung fr Sie stellen. Sie mssen in der Bestellung das Folgende angeben: den Namen und den Sitz Ihrer Firma; den Namen des Leiters; den Namen und Kontaktangaben der Person, die fr technische Fragen verantwortlich ist; die genaue Konfiguration (den Satz) der Module, die Sie kaufen mchten und ihre Anzahl; welche Buchhaltungsunterlagen Sie bentigen.
Nach der Bezahlung der Rechnung werden wir Ihnen den Lizenzschlssel und die notwendigenUnterlagen zusenden.
mailto:[email protected]:[email protected]://www.shareit.com/product.html?cart=1&productid=300356897http://www.regnow.com/softsell/nph-softsell.cgi?ss_short_order=true&items=28256-18/12/2019 Installation Guide for AutoFEM Lite
52/122
8/12/2019 Installation Guide for AutoFEM Lite
53/122
53 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 53
1. Installation de AutoFEM
1.1 Exigences au logiciel AutoFEM est un plugin pour AutoCAD pour le systme d'exploitation Windows XP/Vista/7/8. AutoFEM Analysis 2.x est compatible avec les versions d'AutoCAD 2007, 2008, 2009, 2010, 2012, 2013, 2014. AutoFEM Analysis 2.x ne fonctionne pas avec les versions d'AutoCAD pour Mac OS.
1.2 Ouverture du paquet d'installationDcompressez le paquet d'installation autofem-x64.zip ou autofem-x86.zip. Assurez-vous que vousavez dball le paquet distributive de la mme capacit que votre AutoCAD install a (x64 ou x86). Lepackage d'installation contient les dossiers et fichiers suivants:
Fichiers du paquet de distribution d'AutoFEM pour x64 ( gauche) et x86 ( droite)
Le dossier x64 ou x86 contient les fichiers Microsoft services, ncessaires pour le travail de logicielsdans l'environnement Windows oprationnelles. Si le fichier Setup-x64.exe (ou Setup-x86.exe) ne peuttre lanc sur votre ordinateur, il est ncessaire d'installer le fichier redist2010 du dossier l'avance.Pour les versions d'AutoCAD 2007, 2008 et 2009, le fichier du dossierredist2005 tre install dans lesystme.Pour les versions AutoCAD 2010 et 2012, le fichier du dossier redist2008 doit tre install dans lesystme.
Pour les versions d'AutoCAD 2013 et 2014, le fichier du dossier redist2010 doit tre install dans lesystme.
Ces fichiers peuvent galement tre tlchargs partir du site officiel de Microsoft Corporation.
1.3 Installation du logiciel (de la part du client)Pour que l'installation soit un succs, vous devez avoir le droit d'installer des logiciels sur votreordinateur. Ouvrez le fichier "Setup-x64.exe" (Setup-x86.exe). Slectionnez la langue de travail del'assistant dans la bote de dialogue qui s'affiche et appuyez sur OK. Ensuite, effectuez les options del'assistant.
8/12/2019 Installation Guide for AutoFEM Lite
54/122
54 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 54
Slection de la langue pour l'installation
Installation de AutoFEM - Etape 2
8/12/2019 Installation Guide for AutoFEM Lite
55/122
55 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 55
Installation de AutoFEM - Etape 3
Installation de AutoFEM - Etape 4
8/12/2019 Installation Guide for AutoFEM Lite
56/122
56 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 56
Installation de AutoFEM - Etape 5
Installation de AutoFEM - Etape 6
8/12/2019 Installation Guide for AutoFEM Lite
57/122
57 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 57
Installation de AutoFEM - dernire tape
1.4 Enregistrement d'AutoFEM dans la version installe d'AutoCAD Aprs la copie des fichiers AutoFEM russi, la bote de dialogue de configuration sera actionne, ce quipermet l'enregistrement du plugin dans la version ncessaire d'AutoCAD. Pour enregistrer AutoFEM
dans AutoCAD, il est ncessaire de cliquer l'intrieur de la deuxime colonne oppose aux versionsd'AutoCAD dans laquelle vous souhaitez utiliser AutoFEM par dfaut. Si vous voulez commencer immdiatement AutoFEM, cliquez dans la premire colonne, puis cliquez sur le bouton "Start AutoFEM
Analysis ". L'accs l'utilitaire est disponible tout moment partir du menu "Dmarrer" et du dossier AutoFEM Analyse 2.x | AutoFEM Analysis 2.x .
8/12/2019 Installation Guide for AutoFEM Lite
58/122
58 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 58
Dialogue d'enregistrement de AutoFEM dans AutoCAD
Ouverture de Fema Tool partir du menu Windows XP/Vista/7
1.5 Lancement d'AutoCAD avec l'analyse de AutoFEM installe Aprs l'installation du systme et de son inscription dans AutoCAD, AutoCAD activez la version afin decommencer travailler avec AutoFEM. Lors de la premire ouverture, la bote de dialogue apparatra,offrant activer le mode d'utilisation de la dmo avec la dure de 15 jours ou de activer la licence. (Pour plus de dtails sur l'activation d'une licence locale, voir 2.1)
8/12/2019 Installation Guide for AutoFEM Lite
59/122
59 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 59
Dialogue l'excution initiale d'AutoCAD aprs l'installation d'AutoFEM
Remarque.Dans certains cas, pour que la barre avec les commandes d'AutoFEM apparaisse, il est ncessairede rinitialiser manuellement l'espace de travail 3D d'AutoCAD. Pour cela, utilisez la commande
AutoCAD "WSCURRENT" avec l'option "Modlisation 3D".Dans la fentre AutoCAD qui s'ouvrira, la barre avec les commandes d'AutoFEM doit apparatre, commeil est montr dans la figure. L'accs aux commandes d'AutoFEM est galement disponible dans le menurespectif d'AutoCAD.
8/12/2019 Installation Guide for AutoFEM Lite
60/122
60 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 60
Commandes d'AutoFEM dans le menu et la barre AutoCAD
8/12/2019 Installation Guide for AutoFEM Lite
61/122
61 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 61
Rinitialisation de l'espace de travail 3D de AutoCAD
8/12/2019 Installation Guide for AutoFEM Lite
62/122
62 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 62
4. La dsinstallation d'AutoFEMLa dsinstallation d'AutoFEM est recommande dans l'ordre suivant.
a) Lancez l'utilitaireFema Tool pour dsenregistrer AutoFEM dans AutoCAD et enlever les tiquesface toutes les versions d'AutoCAD. Cette tape supprime d'AutoCAD le menu et la barreavec les commandes d'AutoFEM. Si cela n'est pas fait avant de dsinstaller AutoFEM dusystme d'exploitation, AutoCAD continuera d'afficher le menu d'AutoFEM en dpit de l'absencedu systme. (Dans ce cas, pour restaurer le menu initial d'AutoCAD, la rinitialisation serancessaire avec l'aide de la commande AutoCAD "CUI").
FEMA Tool dans le menuDmarrer | AutoFEM 2.x d'analyse dans l'environnement Windows XP/Vista/7
Pour dsactiver le chargement Analyse AutoFEM dans AutoCAD, dcochez toutes les casesdebout face toutes les versions d'AutoCAD et appuyez sur "Appliquer"
Cette tape doit tre faite pour tous les comptes d'utilisateur dans Windows, o AutoFEM a tenregistr.
b) Rcuprer la commande deinstalllation de AutoFEM du dossier AutoFEM 2.x d'analyse dans lemenu Dmarrer ou utiliser la commande correspondante dans la section Installer / dsinstaller desprogrammes sur le Panneau de configuration de Windows.
8/12/2019 Installation Guide for AutoFEM Lite
63/122
63 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 63
Rcupration de la commande de dsinstallation AutoFEM dans le menuStart | AutoFEM Analysis 2.x dans le Windows XP/Vista/7
Le systme sera supprim.
8/12/2019 Installation Guide for AutoFEM Lite
64/122
64 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 64
3. AutoFEM Lite limitationsLes limites de l'analyse statique et analyse de flambage sont les suivantes: Vous pouvez slectionner seulement un corps solide d'une seule tude. Vous avez deux types de sollicitations mcaniques pour toute tude (force et pression). Il a une limite de quantit des entits de modle d'application des charges \ restrictions. Vous pouvez analyser seulement les principaux rsultats ( dplacements, contraintes, dformations, etc) des
calculs.
Les limitations de la frquence d'analyse sont les suivants: Vous pouvez slectionner seulement un corps solide d'une seule tude. Vous pouvez d'abord seulement trouver la frquence naturelle. Toutes les forces appliques la structure ne sont pas inclus au calcul. Vous n'avez pas la possibilit de rsoudre des systmes non-fix (dans l'espace).
Les limites de l'analyse de fatigue sont les suivantes: Vous pouvez slectionner seulement un corps solide d'une seule tude. Vous pouvez analyser seulement un vnement de fatigue.Les limites de l'analyse oscillation force sont les suivantes: Vous pouvez slectionner seulement un corps solide d'une seule tude. Vous pouvez utiliser seulement deux conditions limites (force et pression) Vous ne pouvez pas utiliser l'oscillateur mcanique comme une source d'oscillations.
Les limites de l'analyse thermique sont les suivantes: Vous pouvez slectionner seulement un corps solide d'une seule tude. Vous pouvez utiliser seulement deux conditions limites pour l'analyse thermique - la temprature et la convection.
Il n'y a pas de limitations concernant le nombre de degrs de libert pour les tudes, les rapports, etcVous avez un instrument FEA entirement fonctionnel votre disposition
8/12/2019 Installation Guide for AutoFEM Lite
65/122
65 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 65
5. Questions frquentes
O puis-je obtenir le soutien technique concernant AutoFEM?
Si vous rencontrez des difficults l'installation ou l'utilisation d'AutoFEM, la meilleure faon est d'crire directement notre support technique: [email protected]. S'il vous plat soyez clair dans la description de votreproblme et dites nous la version de Windows, AutoCAD et AutoFEM que vous utilisez. Nous vous recommandonsvivement de nous contacter immdiatement au lieu de chercher avec Google. C'est plus efficace et donne demeilleurs rsultats.
Paramtres informatiques recommands pour le travail efficace (professionnel) avecAutoFEM
La modlisation mathmatique des phnomnes physiques appartient la classe de problmes quincessitent normment de ressources informatiques. C'est pourquoi, pour l'utilisation efficace dusystme de modlisation p'lments finis il est recommand d'utiliser l'ordinateur le plus puissantaccessibles l'utilisateur. En outre, l'augmentation de la dimension du problme rsolu peut tre ralisen utilisant des systmes d'exploitation 64 bits.
AutoFEM est disponible en deux versions selon l'dition du systme d'exploitation Windows:1. AutoFEM pour Windows 32 bits (le Windows "standard", par exemple, pour les ordinateurs Pentium III
ou IV). La particularit des systmes d'exploitation 32-bits est l'existence physique li au volumemaximum d'informations adresse (environ 2 Go) ce qui limite les capacits ncessaires l'analysedes systmes avec un grand nombre d'lments finis.
2. AutoFEM pour Windows 64-bits (Windows XP 64 bits, Windows Vista 64-bit, etc). Ce systmefonctionne sur les processeurs qui soutiennent 64-bits (Par exemple, Intel Pentium D, Intel Core 2Duo, AMD 64 et autres). Les systmes d'exploitation avec une capacit de 64-bits permettent l'utilisateur de rpondre de significativement plus grands volumes d'informations et de rsoudre lesproblmes de dimension suprieure.
xigences techniques pour un travail efficace (professionnel) avec AutoFEMProcessor avec soutien de instructions 64-bits , Intel i5, i7 seriesRAM 8 GB min, 32 GB recomendedOperating system Windows XP/7/8 64-bitSoftware AutoCAD x64, AutoFEM x64
Avec quelles versions d'AutoCAD AutoFEM Analyse 2.x fonctionne?
Le systme d'analyse d'lments finis "AutoFEM Analyse" fonctionne avec AutoCAD (x86) 2007, 2008, 2009, 2010,2012, 2013, 2014 pour les systmes d'exploitation bass sur Windows sur x86 plate-forme 32 bits et x64 avec
AutoCAD 2008, 2009, 2010, 2012, 2013, 2014 pour les systmes d'exploitation bass sur la plate-forme Windows64-bit.
Est-ce que AutoFEM fonctionne avec AutoCAD 2011?
Non, elle n'existe pas. Il y a quelques problmes de compatibilit avec AutoCAD 2011. Par consquent, l'analyse AutoFEM ne fonctionne pas avec AutoCAD 2011 x86/x64. Seulement AutoCAD 2007-2010, 2012,2013, 2014 sontentirement pris en charge.
mailto:[email protected]8/12/2019 Installation Guide for AutoFEM Lite
66/122
66 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 66
Est-ce que AutoFEM Analyse ou AutoFEM Analyse Lite fonctionne avec AutoCAD Lite?
Non, elle n'existe pas. AutoFEM Analyse et AutoFEM Analyse Lite peut tre utilis uniquement avec la version complte du logiciel
AutoCAD, car l'espace de travail Modlisation 3D est ncessaire pour analyse par d'lments finis.
Je travaille avec un autre systme de CAO (Inventor, Mechanical Desktop, Solidworks).Puis-je utiliser AutoFEM?
AutoFEM analyse fonctionne uniquement dans l'environnement 3D d'AutoCAD. Il ne fonctionne pas directement avecInventor, Mechanical Desktop, SolidWorks, etc . Toutefois, si vous avez la possibilit d'utiliser AutoCAD, vous pouvezexporter votre modle 3D du systme CAO dans AutoCAD via le format de fichier .SAT (format d'change de fichiers
ACIS) et aprs vous pouvez effectuer l'analyse d'lments finis de votre modle en utilisant AutoFEM.
J'ai install AutoFEM, mais il semble que "Fema Tool" ne fonctionne pas. Qu'est ce peuttre le problme?
Parfois, vous devez installer Microsoft Visual C++ 2010 SP1 Redistributable Package x86 or Microsoft Visual C++2010 SP1 Redistributable Package (x64) avant l'installation de AutoFEM.
Comment puis-je installer AutoFEM sur AutoCAD 2007, 2008?
Parfois, lorsque vous utilisez AutoCAD 2007 ou AutoCAD 2008, vous devez installer lethe Microsoft Visual C++2005 SP1 Redistributable Package x86 ou the Microsoft Visual C++ 2005 SP1 Redistributable Package (x64) avantl'installation AutoFEM.
5. Trucs et astuces
Exigences au modle 3D pour l'analyse des lments finis
La qualit et la possibilit de construire un maillage d'lments finis est fortement dpendante de laqualit des modles, de sorte que lors de la construction des modles 3D des exigences plus strictessont impose que dans la modlisation classique avec AutoCAD. Vous devez tenir compte des exigencessuivantes pour crer des modles tridimensionnels de vos produits avec le but de l'analyse des lmentsfinis. Corps avec intersection mutuels ne sont pas autoriss. Il est impossible de construire un maillage
d'lments finis pour des corps qui ont des intersections. Avant de crer une tude, vous devrieztoujours tester votre modle sur les intersections par la commande spciale d'AutoCAD _ INTERFERE.Cette commande affiche les intersections entre les corps si elles existent. Un conseil est de savoir comment les intersections peuvent tre effaces si les corps se croisant sont constitus du mmematriel. Vous pouvez utiliser la commande d'AutoCAD: _ UNION et unir les corps qui se croisent en uncorps entier.
http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/download/en/details.aspx?id=5638http://www.microsoft.com/en-us/download/details.aspx?id=13523http://www.microsoft.com/en-us/download/details.aspx?id=13523http://www.microsoft.com/en-us/download/details.aspx?id=83288/12/2019 Installation Guide for AutoFEM Lite
67/122
67 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 67
Utilisez la comm ande d'AutoCAD INTERFERE pour vr ifier le m odle. Il y a beaucoupd'intersections. La cration d'une tude d'lments finis est impossible
Un mod le 3D correct n'a pas d'inters ections entre ses parties. Le m aillage d'lme nts finis peut treconstruit.
Il ne doit pas avoir d'espaces entre les corps. Tous les corps qui sont inclus dans l'tude doivent avoir un contactpar une face, arte ou un vertex avec tout autre corps de l'tude. Ainsi, dans l'tude, un corps totalement librement"planant" dans l'espace ne devrait pas exister.
8/12/2019 Installation Guide for AutoFEM Lite
68/122
68 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 68
Modle avec cart entre ses parties. Le Maillage peut tre construit dans certains cas, mais le calcul peut tr eincorrect ou impossible.
Corps 3D doit tre volume clos. Le maillage d'lments finis peut tre construite seulement pour un volume limit. Dans AutoCAD, on peut crer un modle 3D solide qui se compose de plusieurs volumes distincts. Par
exemple, si vous avez un profil multiple extrud (voir la photo) un maillage du corps 3D est impossible. Ainsi, le solide 3D qui se compose de plusieurs volumes distincts n'est pas autorise dans l'tude FEA.Si vous avez un tel solide 3D, vous devez utiliser la commande AutoCAD SOLIDEDIT|SEPARATE avantla cration de l'tude FEA pour sparer le solide unique sur plusieurs volumes indpendants.
8/12/2019 Installation Guide for AutoFEM Lite
69/122
69 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 69
That solid after using SOLIDEDIT|SEPARATE command. Il est recommand d'viter d'inclure des arrondissements, des trous et des lments dcoratifs qui ne sont pas
importants pour la force de conception. Ils peuvent compliquer la construction du maillage d'lments finis etaugmenter la dimension du problme (et ainsi le temps pour rsoudre l'tude). Mais les pices qui ont influencesur la force de la conception doivent tre prsentes dans le modle.
Les corps, unis dans un bloc sont traits comme un corps solide qui est obtenu l'aide d'une unionboolenne de tous les objets dans le bloc. Les corps dans le bloc peuvent se croiser les uns avec lesautres. Aucun espace doit exister entre les corps, car cela va gnrer une erreur de gnration dumaillage.
Comment puis-je appliquer une force (ou la pression) une certaine zone de la partie?
Souvent, les charges sont appliques certains domaines d'une partie que vous voulez tudier. Utilisez lacommande IMPRINT d'AutoCAD pour crer une zone d'application de charge sur une face du modle 3D. Toutd'abord (avant la cration de l'tude !), Vous devez dessiner la gomtrie qui dcrit la zone de chargement, enutilisant les commandes de dessin d'AutoCAD. Puis utilisez IMPRINT pour crer une nouvelle face sur la faceactuelle du modle 3D. Voyez les captures d'cran illustrant les tapes ci-dessous.
8/12/2019 Installation Guide for AutoFEM Lite
70/122
70 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 70
Dessin du contour de la zone de charge
Utilisez la commande IMPRINT
8/12/2019 Installation Guide for AutoFEM Lite
71/122
71 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 71
Slectionnez le corps
Slection du contour
8/12/2019 Installation Guide for AutoFEM Lite
72/122
72 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 72
Suppression du contour
Cration de l'tude et l'application de la force
J'ai cr un rapport de mon tude et je vois une image vide ou un message d'erreur.C'est quoi?Par dfaut, le rapport d'AutoFEM contient des images 3D du rsultat enregistr au format VRML. Pour les voir lesutiliser avec la prsentation VRML du rsultat, vous devez installer le plug-in spcial pour votre navigateur Web. Nousutilisons et testons cette fonctionnalit du systme AutoFEM de rapport en utilisant Cortona3D Vrml viewer qui peuttre librement tlcharg par le lien: http://www.cortona3d.com/install.aspx
http://www.cortona3d.com/install.aspx8/12/2019 Installation Guide for AutoFEM Lite
73/122
73 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 73
Vous pouvez galement dsactiver la cration de modle 3D VRML du rsultat en utilisant une case spciale dans labote de dialogue des paramtres de rapport.
Le Vrml viewer n'est past install
8/12/2019 Installation Guide for AutoFEM Lite
74/122
74 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 74
Vrml viewer est install
La bote de dialogue des paramtres de rapport
8/12/2019 Installation Guide for AutoFEM Lite
75/122
75 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 75
7. Comment on peut acheter lAnalysis dAutoFEM?
Il y a deux moyens principaux de payer la version commerciale et recevoir la cl de licence.
Le premier moyen. Vous pouvez utiliser les services des compagnies d'enregistrements RegNow(confortable pour les tats-Unis et d'autres pays dans le monde entier) ou ShareIt! (plus confortablepour les utilisateurs europens). Il y a quatre avantages principaux de l'acquisition de la licence par RegNow ou ShareIt! :
N'importe quelles variantes de paiement. Ces compagnies acceptent divers variantes des paiementslectroniques, les cartes bancaires ainsi que les virements bancaires. Ils accordent aussi l'acheteur tous les documents de comptabilit ncessaires (factures etc.), s'il vous en avez besoin. Le Prix est fix . RegNow et ShareIt! servent la licence de lAnalyse dAutoFEM au mme prix qu'est
indiqu sur notre site. Si vous tes intress des modules ou des ensembles non-standard absentsur le site des enregistreurs crivez nous sur l'adresse [email protected]. (Cette adresseemail est protge contre les robots de spam, vous devez activer Javascript pour la voir.), et nousvous prparerons la commande individuelle.
La Vitesse de l'achat. Si vous payez par le virement lectronique (par exemple PayPal) ou par lacarte de crdit, en gnral, la cl de licence vient vous par e-mail dj dans les minutes qui suiventle paiement.
La Scurit. L'achat par RegNow ou ShareIt! est le moyen le plus sr de l'acquisition de la licence delAnalyse d AutoFEM, puisque vous payez l'argent l'intermdiaire qui fonctionne comme arbitreindpendant et ainsi garantit que vous recevez absolument la cl de licence dans la configurationcommande par vous-mme.
Le deuxime moyen. Vous pouvez dposer le montant du prix de la licence directement sur le comptede notre compagnie (AutoFEM Software LLP). Pour cela vous devez nous fair une demande d offre l'e-mail [email protected] et nous prsentons une facture pour le paiement. Dans la commande ilest ncessaire d'indiquer :
Le nom et le domicile de votre compagnie; Nom du chef de la compagnie; Nom et coordonnes de la personne rsponsable des questions techniques. La configuration (ensemble) exacte des modules que vous voulez acqurir ainsi que leur quantit; quels documents de comptabilit sont ncessaires pour vous.
Aprs le paiement nous vous envoyons la cl lectronique et tous les documents ncessaires.
mailto:[email protected]:[email protected]://www.shareit.com/product.html?cart=1&productid=300356897http://www.regnow.com/softsell/nph-softsell.cgi?ss_short_order=true&items=28256-18/12/2019 Installation Guide for AutoFEM Lite
76/122
76 AutoFEM Softwar e LLP www.auto femsoft.com
Guide d'installation pour AutoFEM Lite (franais) 76
Gua de instalacinde Anlisis AutoFEM Lite (espaol)
Versin 2.2
2014 AutoFEM Softw are LLP
8/12/2019 Installation Guide for AutoFEM Lite
77/122
77 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 77
1. AutoFEM Analysis Installation
1.1 Requisitos para el software Anlisis AutoFEM es un plugin para el AutoCAD para el sistema operativo de Windows XP/Vista/7/8. AutoFEM Analysis 2.x funciona con las versiones de AutoCAD 2007, 2008, 2009, 2010, 2012, 2013,2014.
AutoFEM Analysis 2.x no funciona con versiones de AutoCAD para Mac OS.
1.2 Desembalaje del paquete de instalacinDescomprima el paquete de instalacin AutoFEM-x64.zip o AutoFEM-x86.zip. Asegrese de que hadescomprimido el paquete de distribucin de la misma capacidad que el AutoCAD instalado tiene (x64 o
x86). El paquete de instalacin contiene los siguientes archivos y carpetas:
Archivos del el paquete de instalacin de AutoFEM para x64 (izquierda) y x86 (derecha)
La carpeta x64 o x86 contiene archivos de servicio de Microsoft, necesario para el trabajo de softwareen Windows. Si el archivo Setup-x64.exe (o Setup-x86.exe) no se pondr en marcha en su ordenador,es necesario instalar el archivo de la carpeta redist2010.Para las versiones de AutoCAD 2007, 2008 y 2009, el archivo de la carpeta redist2005 debe estar instalado en el sistema.
Para las versiones de AutoCAD 2010 y 2012, el archivo de la carpeta redist2008 debe estar instalado enel sistema.Para las versiones de AutoCAD 2013 y 2014, el archivo de la carpeta redist2010 debe estar instalado enel sistema.
Estos archivos tambin se pueden descargar desde la pgina oficial de Microsoft Corporation.
1.3 Instalacin del software (parte del cliente)Para que la instalacin sea un xito, debe tener el derecho a la instalacin de programas de software ensu ordenador. Active el archivo "Setup-x64.exe" (Setup-x86.exe). Seleccione el idioma de trabajo de laasistente en el cuadro de dilogo que aparece y pulse Aceptar. A continuacin, realice las opciones delasistente.
8/12/2019 Installation Guide for AutoFEM Lite
78/122
78 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 78
Seleccin de un idioma para la instalacin
8/12/2019 Installation Guide for AutoFEM Lite
79/122
79 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 79
Instalacin de AutoFEM Anlisis - Paso 2
Instalacin de AutoFEM Anlisis - Paso 3
8/12/2019 Installation Guide for AutoFEM Lite
80/122
80 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 80
Instalacin de AutoFEM Anlisis - Paso 4
Instalacin de AutoFEM Anlisis - Paso 5
8/12/2019 Installation Guide for AutoFEM Lite
81/122
81 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 81
Instalacin de AutoFEM Anlisis - Paso 6
Instalacin de AutoFEM Anlisis - ltimo paso
1.4 Inscripcin de AutoFEM en la versin de AutoCAD instaladaTras el xito de la copia de los archivos de AutoFEM, el dilogo de configuracin especial se activa, loque permite el registro de plug-in de AutoCAD. Para registrar AutoFEM en AutoCAD, es necesario hacer clic en el interior de la segunda columna opuesta a las versiones de AutoCAD en el que desea utilizar
AutoFEM Anlisis. Si desea iniciar inmediatamente AutoFEM Analysis, haga clic dentro de la primeracolumna y luego haga clic en el botn "Start AutoFEM Analysis". El acceso a la utilidad est disponible
8/12/2019 Installation Guide for AutoFEM Lite
82/122
82 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 82
en cualquier momento desde el men Inicio y la carpeta AutoFEM Analysis 2.x | AutoFEM Analysis2.x
El dilogo de la inscripcin de AutoFEM en AutoCAD
Recuperacin de la "Fema Tool" en el men de Windows XP/Vista/7
1.5 Lanzamiento de AutoCAD con de AutoFEM instaladoEn la primera puesta en marcha, aparecer el cuadro de dilogo, que ofrece para cambiar del modo deuso de demostracin con la duracin de 15 das o para activar la licencia. (Para ms informacin sobrela activacin de una licencia local, vase el punto 2.1)
8/12/2019 Installation Guide for AutoFEM Lite
83/122
83 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 83
Dilogo en el inicio de AutoCAD despus de la instalacin de Anlisis AutoFEMNota.En algunos casos, para la cinta con los comandos de Anlisis AutoFEM a aparecer, es necesarioreiniciar manualmente espacio de trabajo 3D de AutoCAD. Para ello, utilice el comando de AutoCAD"_WSCURRENT" con la opcin "3D Modelling".En la ventana de AutoCAD que se abrir, la cinta con los comandos de Anlisis AutoFEM debeaparecer, como se muestra en la figura. El acceso a los comandos de AutoFEM Analysis estdisponible tambin en el men correspondiente de AutoCAD.
8/12/2019 Installation Guide for AutoFEM Lite
84/122
84 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 84
Comandos de Anlisis AutoFEM en el men y AutoCAD cinta
8/12/2019 Installation Guide for AutoFEM Lite
85/122
85 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 85
Restablecimiento de espacio de trabajo en 3D de AutoCAD
8/12/2019 Installation Guide for AutoFEM Lite
86/122
86 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 86
2. Desinstalacin de Anlisis AutoFEM LiteSe recomienda la desinstalacin de Anlisis AutoFEM para realizar en el siguiente orden.
a) Ejecute la utilidad "Fema Tool" para anular el registro Anlisis AutoFEM en AutoCAD, y retire lassealas opuestas a todas las versiones de AutoCAD. Este paso elimina de AutoCAD al men yla cinta con los comandos de AutoFEM. Si no se hace antes de desinstalar AutoFEM del sistemaoperativo, a continuacin, AutoCAD continuar mostrar el men Anlisis AutoFEM. (En estecaso, para restaurar el men inicial de AutoCAD, es necesario el uso de comandos "CUI" del
AutoCAD).
La recuperacin de la utilidad "FEMA Tool" en el menInicio | AutoFEM Analysis 2.x en Windows XP/Vista/7
Para anular el registro de Anlisis AutoFEM en AutoCAD, quite todas las marcasde pie frente a todas las versiones de AutoCAD y pulse "Apply"
Este paso debe hacerse para todas las cuentas de usuario de Windows, donde Anlisis AutoFEMha sido registrada.
b) Inicie el comando deinstalllation de Anlisis AutoFEM de la carpeta 2.x AutoFEM Anlisis en elmen Inicio o el comando correspondiente en la seccin Instalar/desinstalar programas en el Panelde control de Windows.
8/12/2019 Installation Guide for AutoFEM Lite
87/122
87 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 87
Inicio del comando de desinstalacin AutoFEM en el menStart | AutoFEM Analysis 2.x in Windows XP/Vista/7
Se eliminar el sistema.
8/12/2019 Installation Guide for AutoFEM Lite
88/122
88 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 88
3. AutoFEM Anlisis Lite limitaciones
Limitaciones del anlisis esttico y anlisis de pandeo son los siguientes: Usted puede seleccionar un cuerpo slido / superficie para su estudio. Hay dos tipos de cargas mecnicas para cualquier estudio (fuerza y presin). Hay un nmero limitado de entidades de modelo para la aplicacin de cargas / restricciones. Usted puede analizar slo los resultados principales (desplazamientos, tensiones,
deformaciones, etc) para realizar los clculos. Slo se puede utilizar la restriccin total (fijacin inamovible).
Limitaciones del anlisis de frecuencia son las siguientes: Usted puede seleccionar un cuerpo slido para su estudio. Usted puede encontrar solamente la frecuencia natural de primera. Las fuerzas aplicadas al diseo no se incluyen en el clculo.
Usted no tiene ninguna posibilidad de resolver no fijo (espacio libre) del sistema.
Limitaciones del anlisis de fatiga son los siguientes: Usted puede seleccionar un cuerpo slido para su estudio. Puede analizar un solo problema de fatiga evento.
Limitaciones del anlisis oscilacin armnica forzado son los siguientes: Usted puede seleccionar un cuerpo slido / superficie para su estudio. Hay dos tipos de cargas mecnicas para cualquier estudio (fuerza y presin). No se puede utilizar el oscilador mecnico como fuente de oscilaciones.
Limitaciones del anlisis trmico son: Usted puede seleccionar un cuerpo slido para su estudio. Usted puede utilizar slo tres condiciones de contorno para el anlisis trmico que son la
temperatura, la conveccin y una potencia calorfica.
No hay ninguna limitacin en cuanto al nmero de grados de libertad para todos los estudios, informes,controles de estudio, etcUsted tiene FEA instrumento altamente eficaz para sus propsitos.
8/12/2019 Installation Guide for AutoFEM Lite
89/122
89 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 89
4. Preguntas ms frecuentes
Dnde puedo obtener el apoyo con respecto a AutoFEM?
Si tiene dificultades para instalar o utilizar AutoFEM, la mejor manera de tratar de resolverlos es ir directamente a nuestro correo electrnico de soporte tcnico: [email protected]. Por favor, ser claro en la descripcin de su problema y nos dice la versin de Windows, AutoCAD y AutoFEM, queest utilizando. Le recomendamos ponerse en contacto de inmediato con nosotros en lugar de buscar en Google todas las preguntas, en relacin con la instalacin AutoFEM, etc, es ms eficaz y da losresultados.
Cules son los requisitos del sistema se recomienda para trabajar con AutoFEMAnalysis?
Modelacin matemtica de los fenmenos fsicos pertenece a la clase de los problemas intensivos enrecursos que requieren importantes recursos computacionales. Es por eso que, para un uso eficientedel sistema de elemento finito de modelado, se recomienda utilizar los ms potentes ordenadoresaccesibles al usuario. Por otra parte, el aumento de la dimensionalidad del problema resuelto se puedelograr mediante el uso de 64-bit sistemas operativos.
Anlisis AutoFEM est disponible en dos versiones segn el capasity bits del sistema operativoWindows:1. AutoFEM para Windows 32-bit (standard de Windows, por ejemplo, para los equipos PentiumIII o IV). La caracterstica distintiva de los sistemas operativos de 32-bit es la existencia de fsico
ligado al volumen mximo de informacin dirigida (cerca de 2 GB), lo que limita las capacidadesnecesarias para el anlisis de sistemas con gran nmero de elementos finitos.2. AutoFEM para Windows 64-bit (Windows XP 64-bit, Windows Vista 64-bit y etc.) Este sistemafunciona en los procesadores que soportan instrucciones de 64 bits. Los sistemas operativos concapacidad de dgitos de 64-bit permiten al usuario frente a volmenes significativamente mayores deinformacin y resolver los problemas de mayor dimensionalidad.
Procesador with support of 64-bit instructions, Intel i5, i7series
RAM 8 GB min, 32 GB recomendedSistema operativo Windows XP/7/8 64-bitSoftware AutoCAD x64, AutoFEM x64
Qu versiones de AutoCAD funciona AutoFEM Anlisis?
El sistema de anlisis de elementos finitos "AutoFEM Anlisis" est trabajando con AutoCAD (86) 2007,2008, 2009, 2010, 2012, 2013, 2014 para Windows x86 plataforma de 32 bits y con AutoCAD 2009,2010, 2012, 2013, 2014 para Windows de 64 bits.
Funciona AutoFEM con AutoCAD 2011?No, no lo hace. AutoFEM no funciona con AutoCAD 2011 x86/x64. Slo AutoCAD 2007-2010, 2012,2013, 2014 son totalmente compatibles.
mailto:[email protected]8/12/2019 Installation Guide for AutoFEM Lite
90/122
90 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 90
Funciona el Anlisis AutoFEM con AutoCAD Lite?
No, no lo funciona. AutoFEM Anlisis y AutoFEM Anlisis Lite se puede utilizar slo con la versincompleta de AutoCAD, porque el espacio de modelado en 3D es necesaria para el anlisis deelementos finitos.
Estoy trabajando con otro sistema de CAD (Inventor, Mechanical Desktop, Solidworks).Puedo utilizar AutoFEM?
AutoFEM slo funciona en el entorno 3D de AutoCAD, que no trabaja directamente con Inventor,Mechanical Desktop, SolidWorks, etc. Sin embargo, si usted tiene la posibilidad de utilizar AutoCAD,puede exportar su modelo 3D a partir del sistema CAD en AutoCAD a travs de SAT formato del archivo
(ACIS formato de intercambio de los archivos) y entonces usted puede intentar para proporcionar anlisis de elementos finitos de su modelo de uso de AutoFEM.
5. Consejos y trucos
Requisitos para el modelo slido 3D para el anlisis de elementos finitos
La calidad y la posibilidad de construir una malla de elementos finitos es dependiente de la calidad de losmodelos de volumen de la estructura. Debe tener en cuenta los s iguientes requisitos para crear modelos
tridimensionales de sus productos para el anlisis de elementos finitos. No se permiten slidos mutuos o de auto-interseccin. Es imposible construir una malla de elementos
finitos para cuerpos de interseccin. Antes de crear un estudio siempre debe probar su modelo en lasintersecciones de comando especial AutoCAD _ INTERFERE. Este comando muestra lasintersecciones entre los cuerpos si lo son. Usted puede utilizar el comando de AutoCAD:UNION y unir interseccin cuerpos en un solo cuerpo.
8/12/2019 Installation Guide for AutoFEM Lite
91/122
91 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 91
Usando el comando de AutoCAD _INTERFIERE para comprobar e l modelo en lasintersecciones
Modelo correcto no tiene intersecciones entre las partes. La malla de elementos finitos puede ser construido Entre los slidos deben no haber espacios. Todos los cuerpos, que se incluyen en un estudio, deben
tener un contacto por una cara, o borde, o vrtice, con cualquier otros slidos del estudio. As que en elestudio, un cuerpo totalmente unengaged no debera existir ya que es como libremente "flotando" en elespacio.
8/12/2019 Installation Guide for AutoFEM Lite
92/122
92 AutoFEM Softwar e LLP www.auto femsoft.com
Gua de instalacin de Anlisis AutoFEM Lite(espaol) 92
Model w ith gap betw een its parts. Mes h may be constructed in som e cases , but calculation can be incorrect