IP�Video�IntercomUniversal�User�Manual
Wifi�Intercom-D
Android iOS
1 2
1 System Wiring Diagram
System list:
Outdoor station, IP camera, Indoor monitor, Router, Switch, Smart phone.
Note: Support PoE Function if use PoE splitter in outdoor station.
System Wiring
(Miltple Devices)
Doorbell
5.Red(DC+12V-18V/1A)
10
Door4
Doorbell
Black(GND)
Red(DC+12V)
System Wiring
(one to one)
Note: Support PoE Function if use PoE splitter in outdoor station.
3 4
2 Indoor Monitor Operation
picture 2.1
2.1 Introduction
1) There are Menu, Shortcut Keys, Status, as picture2.1.
2) Menu including: Recording Center, Security Zone, Monitoring Center,
Video Intercom, User Setup, System Setup.
3) Shortcut key including: Ringtone On/Off, Outdoor Station Monitoring,
one key arm.
4) Status Icon from left to right means:
① Network status: Connected, Disconnected,
Network Conflict.
② Security status: Arm, Disarming, Alarming.
③ Unread message:
④ Missed call:
⑤ WiFi connection:
2.2 Video Intercom
2.2.1 Internal Call
2.2.2 Cloud Intercom
2.2.2.1 WiFi Connection
Connect up to 9 indoor monitor extensions and support “Click to call the monitor
extension” or “the other is not online” if the monitor extension is not setting
successfully or offline. as picture 2.2.1
The smart phone can communicate with visitor when the bell is pressed.
Before that, you need to connect the WIFI Router and select the Cloud
Server in indoor monitor firstly,bind with smart phone by APP.Meanwhile,
when the bell is pressed,there will be a notification in the smart phone.
Note: only available to set the “ Cloud Intercom Function” in “ 01 Monitor
Extension”
Click “ Wifi Connection ” to enter the interface and connect the related Wifi
Name when there is Wifi list.As picture 2.2.2.1
Transform to enter Capital or Lowercase Letter.
Transform to enter Number or Letter.
Delete the input.
Confirm to connect the Wifi.
picture2.2.1
5 6
2.2.2.2 Server Selection
Click “ Sever Selection ” to select the related server which is near you, to
have better Cloud Intercom Experience.As picture 2.2.2.2.
-“Default”: is the server in China.
-“Ap-southeast-1”: is the server in Singapore.
-“Ap-southeast-2”: is the server in Sydney/Australia.
-“Us-east-1”: is the server in Dubai/UAE.
-“Eu-central-1”: is the server in Frankfurt/Germany
picture 2.2.2.2
picture 2.2.2.1
2.2.2.3 Mobile Binding
2.3 User Settings
Click “ Mobile Binding ” to have the records list which smart phone binding
with the Indoor Monitor to have Cloud Intercom Function. Meanwhile,you
can delete a record or all records after selected.As picture 2.2.2.3.
Note: “Cloud Intercom Function” in smart phone is not available if you delete
the binding record in the indoor monitor.
Click to enter “ User Settings Interface” as picture 2.3.
: Click “ One Circle Button” to enter the next user settings page.
picture 2.2.2.3
picture 2.3
7 8
2.4 Software Upgrade
2.5 Record Mode Setting
Caution: Don’t shut off power during the software is upgrading or the indoor
monitor will not work any more.
Click “Upgrade” to enter the Software Upgrade.
1). Support SD Card Software Upgrade that need to put “image.dd” and
“NetCfg.dat” in related SD Card.
2). Assembly SD Card in the indoor monitor and shut off power to reset the
indoor monitor accordingly. Then, enter “ Upgrade” menu as the above
instructions.
3). Select “NetCfg” or “Program” to upgrade the Program and Network
Configuration separately. As picture 2.4.
A. Select “NetCfg” firstly and click “OK” to upgrade the Network Configuration,
it will reboot automatically to be upgradedsuccessfully.
B. Select “Program” firstly and click “OK” to upgrade the Program, it will reboot
automatically to be upgraded successfully.
“Record Mode” is including Record and Snapshot, to set the outdoor station
record mode when the householder missed the call or answered the call.
Record is “take the video of visitor” and Snapshot is “take the photo of visitor”.
As picture 2.5.
picture 2.4
2.6 Outdoor Station Parameters Resetting
Support to review and change the Outdoor Station Parameters.
As picture 2.6.
1). Input “Door Extension Number” and cl ick “OK” to have related door
extension parameters such as “Unlock Time”, “Ring Volume”, “Call Volume” ,
“ Motion Sensitivity”, “Software Version”.
2). Support to change the parameters, need to delete the previous parameters
and input new ones. Then, click “OK” to change successfully.
picture 2.5
picture 2.6
9
Display: 7" TFT LCD(color)
Resolution: 1024*600
Vibration: Bell≥70dB
Power: DC 12V/2A
Current: <350mA
Working temperature: -20℃~+70℃
Max power consumption: <5W
Mension: 226mm*151mm*23mm
Installation: surface mounted
4 Technical Configuration
3 Installation Diagram