www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 1
ITE Final Exam Answer v5 & v5.02
2015 (100%)
1. Which statement is true about the use of an antistatic wrist strap?
An antistatic wrist strap should not be used in conjunction with an antistatic mat.
For optimum grounding, the clip should be attached to a painted section of the computer case.
The metal part of the wrist strap should not make contact with your skin.
An antistatic wrist strap should not be worn when repairing a power supp ly.
2. Which action can reduce the risk of ESD damage when computer equipment is
being worked on?
working on a grounded antistatic mat
lowering the humidity level in the work area
moving cordless phones away from the work area
keeping the computer plugged into a surge protector
3. A customer is upset and wants to speak to a specific technician to resolve a
problem immediately. The requested technician is away from the office for the
next hour. What is the best way to handle this call?
Refer the angry customer to a supervisor.
Advise the customer that the requested technician is out of the office and insist on trying to
resolve the problem.
Make an offer to help the customer immediately, and advise the customer that otherwise the
requested technician will call the customer back within two hours.
Ignore the request for the specific technician by walking through a step -by-step process with the customer in an attempt to refocus the customer and solve the problem.
4. What approach should a technician take when receiving a call from a stressed
customer?
Ask the customer to telephone back when the customer is feeling less stressed.
Ask the customer to hold, and then wait five minutes for the customer to calm down.
Try to establish a rapport with the customer.
Transfer the customer to a level-two technician who will ask the customer to explain the
problem again.
5. A call center technician answers a call from a frequent customer who is known
to be impatient and lacks experience with computers. The customer has an issue
with an application that the call center supports. The customer informs the
technician that the problem had been reported before but the original technician
was rude, did not listen, and did not fix the problem. If the technician is
confident that the problem can be resolved by increasing the amount of memory
in the computer, what should the technician do?
Tell the customer to install 2 GB of DDR3 PC3-10600 RAM.
Explain that the original technician is no good and the supervisor will be told.
2
Suggest that the customer purchase a new computer.
Confirm the issues and give detailed instructions to solve the problem.
6. A call center technician has asked a customer to perform a simple operation to
fix a problem on a computer. The customer seems unable to perform the task.
What should the technician do?
Explain to the customer that it is a simple task and ask the customer to try it again.
Ask the customer to find someone with more experience to perform the task.
Tell the customer that another technician will explain the task .
Determine whether the customer would prefer to receive the instructions in another form, such as emailed, illustrated written instructions.
7. What two actions are appropriate for a support desk technician to take when
assisting customers? (Choose two.)
Interrupt customers if they start to solve their own problems.
Comfort a customer by minimizing the customer problem.
Let a customer finish talking before asking additional questions.
If you have to put the customer on hold, ask the customer for permission.
As soon as you detect customer anger, pass the angry customer to the next level.
8. A user has installed a new printer. Which two pieces of information about the
printer operation are provided by printing a test page from the computer?
(Choose two.)
confirmation that the color calibration is optimized
verification of print spool settings
confirmation that duplex (double-sided) printing is working correctly
verification that driver software is working correctly
confirmation that printer and computer are communicating
9. Which two procedures should be done before performing preventive
maintenance on a laptop? (Choose two.)
Attach any devices that are normally used as part of daily operations.
Verify that all drivers are current.
Ensure the BIOS is the latest version.
Disconnect the AC adapter.
Remove the battery.
Ensure the latest operating system updates have been applied.
10. What is a typical task performed by a level one technician in a call center?
gathering information when a customer calls for help
solving the problem that might require opening up the computer case
using remote access software to troubleshoot the customer computer
picking up an escalated work order and calling the customer for further information
11. What laptop component converts DC power to AC so that the display can
illuminate?
inverter
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 3
backlight
CCFL
battery
motherboard
12. A technician needs to configure a Bluetooth headset for a laptop user. Which
two steps should the technician take before installing the headset? (Choose two.)
Remove the battery.
Disconnect AC power.
Enable Bluetooth in BIOS Setup.
Ensure that the antistatic wrist strap is attached to a nonpainted portion of the laptop.
Ensure that the laptop Bluetooth switch is enabled.
13. Which three actions should be part of a regular computer preventive
maintenance plan? (Choose three.)
removing dust from fan intakes, the power supply, and peripherals
installing appropriate security updates
removing unused or unwanted programs
changing browser settings
deleting old email
installing more RAM in the machine
14. A computer technician performed a number of actions to correct a problem.
Some actions did not solve the problem, but eventually a solution was found.
What should be documented?
everything that was done to try to solve the problem
only the solution, because this solved the problem
only the failed attempts, so that future technicians will know what not to try
a description of the problem and solution
15. What are two operating systems that are found on mobile devices? (Choose
two.)
Android
iOS
Apple
MobileOS
16. A user updates a device driver and reboots the system. When the user
successfully logs in after the reboot, the OS displays a blue screen and crashes.
The user presses the F8 key on reboot and tries to log in using the Last Known
Good Configuration but gets the same result. Why will the Last Known Good
Configuration not work?
The Last Known Good Configuration is overwritten with the current one on successful login.
The boot.ini file is corrupt.
The user failed to run chkdsk prior to logging in.
The user failed to save the CMOS settings on reboot.
4
17. A technician has been asked to reinstall the OS on a computer that has a
corrupted operating system. The technician inserts the installation media in the
optical drive. What would be the most likely action the technician should
perform next?
Change the boot sequence in the BIOS.
Change the BIOS password.
Flash the BIOS for a firmware upgrade.
Change clock speeds in the BIOS.
18. A technician is troubleshooting a computer that fails to print. The technician
suspects that the printer driver may be outdated, proceeds to download the latest
driver, and installs it. The technician attempts to print, but the problem persists.
What is the next action that the technician should take?
Develop a new theory.
Test the theory.
Establish a plan of action.
Identify the problem.
19. A technician is troubleshooting a printer that fails to print because of
constant paper jams. What should the technician try first?
Clean the printer.
Secure printer cables.
Configure the printer port.
Check for bent pins on the printer cable.
20. A technician is planning an operating system upgrade for a user system that
is currently running Windows Vista. Because the BitLocker feature embedded in
the Windows Vista OS is required, there is a request that this feature be
available when the new operating system is installed. Which version or versions
of Windows 7 would support this feature?
Windows 7 Ultimate
Windows 7 Ultimate and Professional
Windows 7 Ultimate and Professional and Home Premium
Windows 7 Ultimate and Professional and Home Premium and Starter
21. What is different about the default location for user files in Windows Vista
compared to Windows XP?
The default location for user files in Windows Vista is within a user-specific subfolder in the
Users folder.
The first time a user logs into any version of Windows Vista, the user must select the default
folder for user files.
During the installation process, the installer selects the folder from which subfolders are
created for every user to store user-specific documents.
The default location is in the Documents and Settings folder. From there a subfolder with the
user name is created when a user account is made. Then another subfolder called My Documents is created.
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 5
22. Which Windows feature enables a technician at company headquarters to
view the screen and control the mouse and keyboard of a computer in a branch
office?
System Desktop
System Tools
Remote Desktop
Services
23. Which Windows hard drive partition is referred to as the C: drive?
the first volume partition
the first primary partition
the first extended partition
the first logical partition
24. Refer to the exhibit. Which utility has the IT department started on each
computer?
ITE Final Exam Answer 001 (v5.02, 2015)
Chkdsk
Computer Management
Defragment
Scandisk
25. A technician notices that a data floppy disk is in the floppy disk drive of a
computer when it is powered on. Which error message could this potentially
cause?
6
device / service failed to start
floppy disk corrupted
invalid system disk
corrupted driver
26. A user believes that a data file on a Windows XP computer has been
corrupted. Which utility can provide the best information about the data file?
Defrag
Chkdsk
Msconfig
Regedit
27. Engineers are designing a security scheme to allow only authorized persons
to access the facilities of a national bank. Which security control measure
provides the most secure solution for employee identification?
card keys
security guards
security key fobs
biometric devices
28. Engineers are designing a security scheme to allow only authorized persons
to access the facilities of a national bank. Which security control measure
provides the most secure solution for employee identification?
card keys
security guards
security key fobs
biometric devices
29. What type of security attack is being launched when a hacker calls a
company to obtain computer login information and pretends to be an employee?
spyware
phishing
adware
Trojan
social engineering
30. What characterizes a DDoS attack?
Many hosts participate in a coordinated attack.
Infected computers are called daemons.
It is easy to identify the source of the attack.
All hosts must be in the same geographic area.
31. What guideline should be followed when establishing a password security
policy?
Passwords should be physically stored in a convenient location.
Passwords should contain mainly numbers for better encryption.
The system administrator should assign passwords to the users.
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 7
Lockout policies should be avoided in order to increase user access.
An expiration period should be established so that passwords frequently change.
32. After logging into a computer, a user can view files but is unable to download
the files. What action can the administrator take to allow the user to download
the files while preventing deletion of the files?
Set the folder permissions to Read.
Set the file permissions to Modify.
Set the file permissions to Full Control
Set the file permissions to Read and Execute.
33. A technician has been asked to develop a physical topology for a network
that provides a high level of redundancy. Which physical topology requires that
every node is attached to every other node on the network?
bus
hierarchical
mesh
ring
star
34. A network administrator has finished migrating from a peer-to-peer network
to a new client-server network configuration. What are two advantages of the
new configuration? (Choose two.)
The total cost of the new solution is considerably lower.
Data is more secure in the event of hardware failures.
Individual users are in control of their own computers and network resources.
Data resources and access are centrally controlled.
Personnel costs are lower because a dedicated network administrator is no longer necessary.
35. A student enables file sharing on a laptop so that a friend can access music
files. Which type of service is being configured?
FTP
peer-to-peer
Telnet
DHCP
DNS
36. The current IP configuration of a small company is done manually and is
time-consuming. Because of increased network growth, a technician needs a
simpler way for IP configuration of workstations. Which service would simplify
the workstation IP configuration task?
APIPA
DHCP
DIPS
ICMP
37. A computer can access devices on the same network but cannot access
devices on other networks. What is the probable cause of this problem?
8
The cable is not connected properly to the NIC.
The computer has an invalid IP address.
The computer has an incorrect subnet mask.
The computer has an invalid default gateway address.
38. What is the reason for disabling SSID broadcasting and changing the default
SSID on a wireless access point?
Anyone with the default SSID can gain access to the access point and change the
configuration.
Disabling SSID broadcasting frees up radio frequency bandwidth and increases the data
throughput of the access point.
The access point stops broadcasting its own MAC address, thus preventing unauthorized
wireless clients from connecting to the network.
Wireless clients must then have the SSID manually configured to connect to the wireless network.
39. A computer has been assigned an IP address of 169.254.33.16. What
command could be used to force the computer to request an IP address again?
ipconfig /release
net computer
nslookup
tracert
40. After confirming the removal of a virus from a computer, how should the
technician ensure and verify the full functionality of the system?
Check for the latest OS patches and updates .
Document the problem and the procedures performed to solve it.
Talk with the user to determine the cause of the problem.
Gather information from a number of sources to clearly identify the problem.
41. A user wants to upgrade components in a laptop to improve performance.
Which two components can be replaced by the user? (Choose two.)
RAM
battery
motherboard
CPU
LCD display
42. A technician uses the shrink volume feature of the disk management utility
and splits the partition. What must the technician do next in order to make use
of the new space?
Partition the unallocated space.
Format the existing partition.
Delete all partitions and reinitialize the disk.
Convert the unallocated space into a dynamic disk.
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 9
43. A student laptop is running slowly, and the student suspects rogue computers
are accessing the laptop. Which control panel feature is used in Windows Vista
to verify the firewall setting?
Network and Sharing Center
Programs
Security Center
System and Maintenance
44. How does MAC address filtering enable wireless network security at the
device level?
Device MAC addresses are encrypted before being transmitted over the network.
MAC address mutual authentication is enabled between the wireless client and the network.
Use is made of a lightweight access point architecture to control wireless device network
access.
The unique MAC address of each wireless device is filtered and only authorized addresses are
allowed network access.
45. Rogue antivirus warning windows have been reported as appearing on
computers in a company. The computer systems administrator is drafting a
notice to all employees explaining how to deal with this problem. In addition to a
description of the problem and the reporting procedure, which two instructions
should also be included in the notice? (Choose two.)
Do not click anywhere in the warning window.
If the window has to be closed, then press Alt + F4.
Close the window by clicking the cross in the top right corner.
Click the Cancel button in the window to close the window.
Update the antimalware software on the computer.
46. The corporate security policy states that all remote connections use only
secure tunnels for data communications. Which encryption technique secures
data traveling across the public Internet as if it were traveling across the
corporate LAN?
MD5
VPN
WEP
WPA
47. Which protocol adds security to remote connections?
FTP
HTTP
NetBEUI
POP
SSH
48. What are two network requirements necessary to establish a VPN connection
between a remote computer and a private company LAN? (Choose two.)
low latency network connection
10
secure web server
Internet access
PSTN access
VPN client
49. Which statement is true about DDR2 and DDR3 RAM modules?
They operate at the same voltage.
They have a different number of contact pins.
They use different types of DIMM slots on the motherboard.
They require the same operating frequency on the front side bus.
50. A customer needs additional storage space on an older computer. What will
the technician look at in the computer to determine if an additional hard drive
can be added?
adequate RAM
an open PCI/PCIe expansion slot
an available PATA/SATA connection
BIOS version
the heat that is generated and air flow requirements
51. A computer user has a USB 3.0 thumb drive. What USB port or ports could
be used to attach the drive to the PC?
only a directly connected USB 3.0 computer port
only a USB 3.0 computer port or a port on a USB 3.0 hub
only a USB 2.0 or 3.0 port on the computer or on a hub
any USB 1.1, 2.0, or 3.0 port
52. Which step is critical in selecting and installing multiple cooling fans for a PC
case?
Make sure they are the same make and model.
Make sure they run at the same speed.
Make sure they provide the same amount of air flow.
Make sure they are mounted in correct air flow directions.
53. A customer needs to purchase a new power supply for a computer. What
must be considered when selecting an appropriate power supply?
The power supply converts DC to AC.
The power supply has sufficient wattage to support all components inside the computer.
The power supply provides at least 800 V.
The power supply must have both a P-8 and P-9 connector.
54. Refer to the exhibit. To what input device would the cables attach?
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 11
ITE Final Exam Answer 002 (v5.02, 2015)
keyboard/mouse combo device
KVM switch
video distribution center
sound system
55. Which motherboard feature controls the amount of data that a CPU
transfers at one time?
pin grid array
front side bus
MMX instructions
read-only memory
56. Which is the correct procedure to put out a fire with a fire extinguisher after
the pin is pulled?
Aim just above the flame, squeeze the lever, and sweep from side to side.
Aim at the base of the flame, squeeze the lever, and sweep from side to side.
Aim directly at the center of the flame, squeeze the lever, and sweep from side to side.
Aim at the base of the flame, squeeze the lever, and sweep from the base to the top of the
flame.
Aim just above the flame, squeeze the lever, and sweep from the top to the base of the flame.
57. A technician is explaining the differences between inkjet printers and laser
printers to a customer. Which two comparisons should the technician make?
(Choose two.)
Inkjet printers are less expensive as an initial purchase than laser printers.
A laser printer is significantly slower than an inkjet printer.
Both laser and inkjet printers produce poor quality images.
The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the
paper after printing.
Inkjet printers use plain paper to make economical prints, but laser printers require more
expensive thermal paper.
12
58. A customer is angry and calls to complain that the service scheduled on the
computer took longer than expected. The technician reviews the work order and
notices that the service was performed by a new employee. How should the
technician respond?
Verify that the computer is working properly now.
Listen to the complaint and then apologize for any inconvenience caused by the lengthy
service on the computer.
Explain that the repair technician sent to perform the service is inexperienced.
Put the customer on hold until a supervisor is available.
59. Once a technician understands a customer complaint, it is common to ask
closed-ended questions. Which question is a close-ended one?
What happened before the error occurred?
Is this the first time the error occurred?
What happened after the error occurred?
What error messages were displayed when the error occurred?
60. Which two items would be part of a laptop preventive maintenance kit?
(Choose two.)
compressed air
plastic scribe
soft cloth
antistatic wrist strap
flat-head screwdriver
61. In which circumstance should a level one technician initiate an escalated
work order?
when a customer appears to be very knowledgeable
when a customer demands talking to a particular technician
when a problem requires expertise from another technician
when the technician cannot understand the problem as explained by the customer
62. In what circumstance would plenum-rated twisted-pair computer network
cabling be required?
when the required cable run is more than 330 feet in length
when the cable run must be installed inside a ceiling
when the cable run connects to the MDF
when the cabling is installed at a punchdown block in a wiring closet
63. Which three actions should be part of a regular computer preventive
maintenance plan? (Choose three.)
removing dust from fan intakes, the power supply, and peripherals
installing appropriate security updates
removing unused or unwanted programs
changing browser settings
deleting old email
installing more RAM in the machine
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 13
64. A technician is attempting to create virtual machines on a PC but wants to
ensure that the physical system resources used by the virtual machines are
directly managed by them and not by the host operating system. How can the
technician accomplish this?
Set up the virtual machines using a native hypervisor.
Set up the virtual machines using a hosted hypervisor.
Set up the virtual machines as Windows Virtual PCs
Limit the amount of paged RAM.
Disable hyperthreading in the BIOS.
65. Which feature of a mobile device touchscreen will allow a user to zoom in
displayed items such as maps and photographs?
long touch
double touch
pinch
slide
66. A user downloads a widget onto his Android phone but is puzzled to see that
when the widget is touched an app is launched. What is a possible cause?
The user has downloaded a virus.
The widget is corrupt.
The security settings of the Android OS have been compromised.
The widget is associated with the app and this is the normal behavior.
67. After solving a problem on a computer, a technician checks the event log to
ensure that there are no new error messages. At which step of the
troubleshooting process is this action taking place?
Verify the solution and full system functionality.
Document the findings.
Establish a theory of probable cause.
Determine an exact cause.
68. A technician has just installed a new laser printer, but is unable to print a
test page. What is the most likely cause for this?
The installed printer driver is the wrong one.
The printer memory is not enough to handle the printing job.
The size of the paper is incorrect.
The page counter needs to be reset.
69. A user reports that some printing jobs are not being printed. The technician
checks and notices that the jobs are stuck in the printing queue. What action
should the technician take to solve the problem?
Cancel the job that displays the error that is preventing the other jobs from being printed.
Reinstall the printer driver.
Unplug the data cable from the printer and plug it in again.
Plug the printer to a voltage regulator.
14
70. A technician has installed a third party utility that is used to manage a
Windows XP computer. However, the utility is unable to startup automatically
whenever the computer is started. What can the technician do to resolve this
problem?
Uninstall the program and then choose Add New Programs in the Add or Remove Programs
utility to install the application.
Use the Add or Remove Programs utility to set program access and defaults.
Change the startup type for the utility to Automatic in Services.
Set the application registry key value to one.
71. A technician is asked to set up one hard drive that will support two operating
systems and will store data files in three separate drive locations. Which
partition settings will support these requirements?
1 primary, 3 active, 1 extended, 2 logical
2 logical, 2 active, 3 extended
2 primary, 1 active, 1 extended, 3 logical
3 primary, 1 active, 2 extended
72. For security reasons a network administrator needs to ensure that local
computers cannot ping each other. Which settings can accomplish this task?
smartcard settings
firewall settings
MAC address settings
file system settings
73. An administrator receives an email message from what appears to be the
company bank. The email asks for account information. The administrator
determines the email is not from the bank. What type of security threat has the
administrator detected?
spyware
grayware
Trojan
worm
phishing
74. Which two aspects of a computer can be protected by setting the BIOS
password? (Choose two.)
network address assignment method
hard drive settings
operating system login
operating system booting
file system management
firewall settings
75. Which two aspects of a computer can be protected by setting the BIOS
password? (Choose two.)
network address assignment method
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 15
hard drive settings
operating system login
operating system booting
file system management
firewall settings
76. Which two password control policies should an organization implement to
ensure strong passwords? (Choose two.)
Passwords should be set to expire every 60 days.
Passwords should contain no more than eight characters.
Passwords must contain encrypted characters.
Passwords should contain letters and numbers.
Passwords should contain only capital letters.
77. Which open standards-based wireless security mode supports the highest
level of security?
WEP
WPA2
WPA
LEAP
78. In a networking class, the instructor tells the students to ping the other
computers in the classroom from the command prompt. Why do all pings in the
class fail?
A virus is on the classroom computers.
The computers are on different networks.
The Windows firewall is blocking the ping.
Port 25 is blocked and preventing the echo request from being transmitted.
79. A new technician has joined the IT team and is about to service a heavy
printer. Which two precautions should be taken to avoid any injury when
transporting the heavy printer to the service area? (Choose two.)
Avoid lifting the equipment using the strength in your back.
Lift the equipment using the strength in your legs and knees.
Avoid bending your knees when lifting the printer.
Bend your back to pick the printer up.
Avoid lifting the printer close to your body.
80. What can help control the effect of RFI on a wireless LAN?
Ensure the humidity and temperature levels are set as low as possible.
Ensure the number of wireless NICs exceeds the number of wireless phones.
Ensure the wireless network is on a different frequency than the offending source.
Ensure each wireless NIC is configured to operate at different frequencies from all other wireless NICs.
81. The current IP configuration of a small company is done manually and is
time-consuming. Because of increased network growth, a technician needs a
16
simpler way for IP configuration of workstations. Which service would simplify
the workstation IP configuration task?
APIPA
DHCP
DIPS
ICMP
82. What are the four layers in the TCP/IP reference model?
HTTP, TCP, IP, Ethernet
TCP, IP, Ethernet, IEEE
application, transport, internet, network access
application, presentation, session, transport
physical, data link, network, transport
83. A technician is to document the current configurations of all network devices
in a college, including those in off-site buildings. Which protocol would be best to
use to securely access the network devices?
FTP
HTTP
SSH
Telnet
84. A newly hired technician is attaching a computer to the network. Upon
examining the network configuration, the technician recognizes that the
computer is configured with a protocol stack that is used for Internet
communication. What protocol stack is installed on the computer?
AppleTalk
IPX/SPX
NetBEUI
TCP/IP
85. After the administrator manually configures the correct SSID on a new
laptop, the computer is still unable to connect to the wireless LAN. Which
additional action should the administrator take to resolve this problem?
Modify the group account of the user to include all file permissions.
Reboot the wireless access point.
Rename the laptop and reset the user password on the network.
Verify that the MAC address for the laptop is in the MAC address filter table.
86. An audit reveals company files that are stored in the personal server space of
a former employee have been modified after the employee left the company.
What should be done to prevent further unauthorized access to these files, while
still allowing the company to use them?
Disable the account of the former employee.
Delete the account of the former employee.
Delete the files from the server.
Change the account to a Guest account.
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 17
87. How is DSL able to carry telephone and data signals at the same time?
Each signal uses a different frequency.
Each connection is dialed separately.
DSL uses low frequency transmissions.
DSL uses digital signals to carry both the telephone and data traffic.
88. A company has a preventive maintenance policy that requires every
computer have a new restore point created every six months. For computers
using the Windows 7 operating system, how can a technician create the restore
point?
From the CLI enter the command restore /cn.
Choose Start > Control Panel > Accessories > System Tools > System Restore > Create a
restore point.
Choose Start > All Programs > Accessories > System Tools > System Restore > Next.
Right-click My Computer and then choose Properties > Restore > Create Restore Point.
89. Which are two potential risks to a mobile device that could result from
rooting or jailbreaking the device? (Choose two.)?
A custom OS enables user access to the root directory.
A custom OS may not properly create or maintain sandboxing features.
The user interface may be extensively customized.
The device performance may be improved.
Some features initially disabled by a carrier may be enabled.
90. Which three attributes of NTFS make it a better file system than FAT32?
(Choose three.)
file and folder permission options
file size per volume of 4.17 million
journaling
large cluster size
encryption at the file and folder level
maximum individual file size of 4 GB
91. Which memory module used to hold instructions for booting a PC and
loading the OS, but is still used on adapters even though the memory contents
cannot be changed?
RAM
ROM
cache
main memory
92. Why do laptop computers use CPU throttling techniques?
to enhance the performance of the CPU
to reduce the heat that the CPU may generate
to ensure the CPU is running at its peak speed
to conserve the battery life by reducing the bus speed between the CPU and RAM
18
93. A technician is upgrading an ATX motherboard with another ATX
motherboard. Which component might be affected by this and need to be
upgraded and bought as an additional purchase?
BIOS
chipset
CMOS battery
CPU
PCIe adapter
94. A student wishes to buy a computer suitable for game playing. What CPU
speed would be appropriate for game playing?
44.1 MHz
100 MB/s
3 GHz
1 TB
95. What are the terms refresh rate, interlace, and aspect ratio related to?
hard drive efficiency
audio signal
scanner output
image quality of a monitor
96. Which two interface types make it possible to attach different external
components to laptops and desktops without powering the computer off?
(Choose two.)
PS/2
FireWire
PCI
PCIe
USB
CCNA 5 Answers:
CCNA 1 Chapter 1 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 10 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 11 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 2 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 3 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 4 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 5 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 6 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 7 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 8 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter 9 Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Chapter and Final Exam Answer 2015 (100%) CCNA 1 Final Exam Answer v5 & v5.02 2015 (100%) CCNA 1 Practice Final Exam Answer v5.02 2015 (100%)
www.ccna5answers.com www.ccna5blog.com www.ccna-5.com
www.ccna5answers.com 19
CCNA 1 Pretest Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 1 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 10 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 11 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 2 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 3 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 4 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 5 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 6 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 7 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 8 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter 9 Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Chapter and Final Exam Answer 2015 (100%) CCNA 2 Final Exam Answer v5 & v5.02 2015 (100%) CCNA 2 Practice Final Exam Answer v5.02 2015 (100%) CCNA 2 RSE Practice Skills Assessment – PT 2015 (100%) CCNA 3 Chapter 1 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 2 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 3 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 4 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 5 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 6 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 7 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 8 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Chapter 9 Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Final Exam Answer v5 & v5.02 2015 (100%) CCNA 3 Practice Final Exam Answer v5.02 2015 (100%) CCNA 3 Pretest Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 1 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 2 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 3 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 4 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 5 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 6 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 7 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 8 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter 9 Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Chapter and Final Exam Answer 2015 (100%) CCNA 4 Final Exam Answer v5 & v5.02 2015 (100%) CCNA 4 Practice Final Exam Answer v5.02 2015 (100%) CCNA 4 Pretest Exam Answer v5 & v5.02 2015 (100%) ITE Chapter and Final Exam Answer 2015 (100%) ITE Final Exam Answer v5 & v5.02 2015 (100%)