Joint 315A/350A/400A/500A/630A
Digital inverter welding machine
Operation manual
Shanxi Nebula Welding Equipment Co., Ltd.
16
3. Description of the control panel
3.1 Joint A series welding machine panel operating instructions
Figure 3.1 Joint A series welding machine operation panel
3.1.1 Choosing welding process
Press to choose welding process orderly from MMA, TIG, Pulse TIG, Spot TIG,
MIG, Pulse MIG, Double Pulse MIG and Gonging.
3.1.2 Choosing start switch function
17
Press to choose start switch function orderly from 2T, 4T, S2T, S4T and spot
welding, which only work for TIG, Pulse TIG, MIG, Pulse MIG, and Double Pulse MIG
welding processes.
Job is for storing the welding parameters.
3.1.3 Choosing welding material
Press and to choose welding material and matched protect gas as following
form.
Joint A series welding machine support 13 kinds of material.
Only work for MIG, Pulse MIG, Double pulse MIG welding processes.
No. Material Protect gas Welding Wire (AWS)
1 Steel 100% CO2 Carbon Steel wire
2 Steel 80% Ar + 20% CO2 Carbon Steel wire
3 CrNi 18 8 6 98% Ar + 2% CO2 ER307 SS solid wire
4 CrNi19 9 98% Ar + 2% CO2 ER308 SS solid wire
18
5 Rutil 80% Ar + 20% CO2 Acid/Rutil flux-cored wire
6 Basic 80% Ar + 20% CO2 Basic flux-cored wire
7 Metal 80% Ar + 20% CO2 Metal flux-cored wire
8 CrNi 80% Ar + 20% CO2 CrNi flux-cored wire
9 Al99.5 100% Ar ER1050 Al wire
10 AlSi 5 100% Ar ER4043 AlSi wire
11 AlMg 5 100% Ar ER5356 AlMg Wire
12 CuSi 3 100% Ar ER Cu Si wire
13 CuAl 9 100% Ar ER Cu Al wire
3.1.4 Choosing welding wire diameter
Press to choose welding wire diameter orderly from 0.8mm, 1.0mm, 1.2mm,
and 1.6mm.
Only work for MIG, Pulse MIG and Double pulse MIG welding processes.
3.1.5 Use of gas test
If you press the gas test button, the gas will flow without pressing gun trigger. Gas flow
can be measured by the CO2 or Argon flow meter. Gas flow will be stopped when
release the button.
Only work for TIG, Pulse TIG, Spot TIG, MIG, Pulse MIG and Double pulse MIG
welding processes.
3.1.6 Wire Inch
19
If you press the wire inch button, the motor of the wire feeder will start run without
pressing gun trigger. The wire speed will be 3m/min but can be adjusted in startup
setting (see section 3.3).
Only work for MIG, Pulse MIG and Double pulse MIG welding processes.
3.1.7 Welding current adjustment
For MIG, Pulse MIG, Double Pulse MIG welding process, press to choose the
display value as for current, for wire feed speed, or for thickness of
plate. Turn to adjust the current (A), wire feed speed (m/min) or thickness of
plate (mm) value. Due to the built-in synergic adjustment model, anyone of
parameters (current, wire feed speed and thickness of plate) has been adjusted; the
others will be matched automatically.
For MMA, TIG, Pulse TIG, Spot TIG, Gonging welding processes, only current can
be adjusted.
3.1.8 Welding Voltage adjustment
Press to choose the display value as for voltage, for inductance/arc
force, for job and for other parameters.
When the display value is voltage, Turn to adjust the voltage value(V).
20
Only work for MIG, Pulse MIG, and Double Pulse MIG welding process.
Note : For new version, due to the synergic function, the voltage value
automatically matches with the adjusted current. So the display value is zero. But
it can be adjusted within the rang ±50% of the matched voltage value.
When the display value is inductance/arc force, Turn to adjust the
inductance/arc force value. 1) For MIG welding process: the inductance value 0 is recommended reference
range. Value less than 0 give a rougher arc and increased stability. Value greater than 0 give a smoother arc and less spatter.
2) For pulse MIG welding process: The droplet transfer force will be increased according the inductance value changed from less than 0 to greater than 0.
3) For MMA welding process: the arc force value 0 means soft and spatter small arc, value 100 means hard and stable arc.
When the display value is Job, the welding parameter can be stored and recalled.
Please refer to the details on section 3.2
3.1.9 Indicator
WORK: The indicator light when under welding process. HOLD: The indicator light when under no-load working. Error: The indicator light when the welder has some trouble wrong. Robot: The indicator light when connect with the Device net. COM:The indicator light when welding machine communicate with other
equipment.
3.1.10 Menu
The key has two purposes: store the welding parameters and startup Settings menu .
3.2 Welding parameters storage and recall
The storage capacity of Joint A series welding machine can store 100 sets of welding
parameters (Job0—Job99). The suitable welding parameters value for different welding
application can be stored at any time. Its very convenience to recall the stored welding
parameter when use it next time. No need to preset and adjust the welding parameter
21
value each time before welding.
Figure 3.2 Set up storage JOB number
For Job 0, it’s specially used for automatically memory storage, which can store
the last welding parameter automatically. The last welding parameter can be
recalled from Job 0 when restart the welding machine. Operation process of recall
as follow:
1) Press to choose the display value as job.
2) Turn to adjust the Job number as 0.
3) The LED will be display the welding parameter which has been used last time.
For Job 1-99, it’s used for manual storage, Operation process as follow:
1) LED displays the welding parameters which will be stored.
2) Press to choose the display value as job.
3) Press , the front of the Job number will display "-", see Figure 3.2.
4) Turn to choose the Job number as “X”.
5) Press , the LED will display "Finished", means the parameter has been
stored to the Job number “X”.
Operation process of recall as follow:
1) Press to choose the display value as job.
2) Turn to choose the Job number as “X”.
3) The LED will be displayed the welding parameters which has been stored in
Job “X”.
22
3.3 Joint A series welding machine startup Settings.
Some welding parameters of JOINT A series welding machine could be adjusted
through the startup Settings menu, and the operation process as following:
Figure 3.3 startup Settings menu
1) Press on menu key, and turn on the power switch of the machine at the same
time.
2) After few seconds, it enters the Startup Settings Menu, and LED display "Preg" as
Figure 3.3.1.
3) Press to choose , then the left part of the LED display the parameter
name, and right part of the LED display the parameter value.
4) Turn the left side to choose the parameter name, turn the right side to
adjust the parameter value.
5) Press , the LED will display "Finished", means the parameter has been reset
and stored. Then restart the machine and weld.
Adjustable parameters name of startup Settings as following:
1) Pre-gas flow time (PreG): Adjustable from 0-15s, the default value is 0.1s. It works for MIG, Pulse MIG, Double Pulse MIG, TIG, Pulse TIG and Spot TIG.
2) Post-gas folw time (PosG) : Adjustable from 0-15s, the default value is 0.1s. It works for MIG, Pulse MIG, Double Pulse MIG, TIG, Pulse TIG and Spot TIG welding processes.
3) Soft start wire feed speed (Stfd) : Adjustable from 1-22 m/min, and also can be set at automatic. It works for MIG, Pulse MIG and Double Pulse MIG welding process.
4) Inch wire feed speed (Infd) : Adjustable from 1-22 m/min. 5) Master station MACID (NetP) : Master station MACID of Devicenet: 0-63. 6) Slave station MACID (NetS) : Slave station MACID of Devicenet: 0-63. 7) Device net baud rate (Netb) : 0-125 k, 1-250 k, 2-500 k
23
8) System Set 1 (Set1) : Bit0 = 1 means allow the simulation remote control, 0 means banned.
9) System Set 2 (Set2) : temporary undefined. 10) Wire feed machine coefficient (Fdp), wire feed machine constant (Fdc) :
according the different wire feed motor, setting up different coefficient. First Type, 24V, 22M/Min, 5A motor: Fdp = 400; Fdc = 426; Second Type, 24 v, 22 m, 3.5 A motor: Fdp = 371; Fdc = 400;
11) Setting up Password (Pas1, Pas2, Pas3, Pas4) : function password settings.
Figure 3.4 storage success indicator
3.4 Joint A series welding machine status display
JOINT A series welding machine can display some information and status of the welder.
After startup welding, the LED will display the company LOGO, hardware, software
version, welding process, expert database material type and whether support
DEVICENET and WIFI one by one.
Figure 3.5 Company LOGO after startup the welder
Operation process of the welding machine status display
1) Press to choose the display value as .
2) Turn the left side to show different status of the welding machine as following:
24
Figure 3.6 Machine internal temperature is 26℃
Figure 3.7 Hardware version for V23, software version for V1.4
Figure 3.8 Machine serial number as XY000030
Figure 3.9 Actual wire feed speed in 8.5 m/min
4. Installation, Debugging and operation
4.1 Safety Tips
26
4.2 Joint A series welding machine front panel and structure
Figure 4.1 Joint A series welding machine front-panel diagram
A Current knob B Socket for Fast plug “-” C Membrane switch D TIG torch connector
E Argon gas outlet F Voltage knob
4.3 Joint A series welding machine rear panel
A B C D E F
27
Figure 4.2 Joint A series welding machine rear panel diagram
A Power socket for heating CO2 regulator B Fiber converter C Analog control connector D Devicenet communication interface E Wire feeder connector F Air circuit breakers G Three-phase power lines H Argon gas inlet I Power supply socket for water tank J Power socket for water pressure switch K Socket for fast plug”+” L CO2 regulator heating fuse
B C D G E
H JK
F
L K
A
F
29
Figure 4.3 MMA welding connection diagram
4.5.2 Debugging and operation for MMA
30
Figure 4.4 manual welding panel diagram
Adjust the parameter as following steps 1, 2, 3.
1. Use welding process buttons to select MMA welding method. 2. Twist the knob A to adjust the current. 3. Twist Knob M to set the arc force. 4. Begin to weld All the parameters in steps 1.2.3 could be saved automatically when the machine is working and remain the same even if the machine is killed halfway. The MMA welding has seven adjustable parameters: 1. Current: The range (10A ~ rated current) is welding current, please choose the proper
current according to welding technology.
2. Arc force: 1 ~ 100, refers to the slop of current rise in the process of short circuit. It should be settled based on electrode diameter, set current value and welding procedure requirements. The stronger arc force, the faster droplets, the less sticking. However, too strong arc force would increase splashes. The weaker arc force, the lower splashes, the better welding seam, but sometimes, people feel that the arc is soft or cause sticking. So the
Knob A Knob M
MMA
31
arc force should be increased when use wide electrode rod (4mm) with small current (120A). The arc force should be 10~50 in general.
3. Hot starting arc current (HotI) : 0 ~ 100%, 20 refers to Hot starting arc current = welding current + 20% * welding current.
The hot starting arc time (Hott) : 0 ~ 1.5 s, refers to the duration of Hot starting arc time. In order to strike arc successfully, the welder would output a high current as striking current, the duration of striking current is determined by the ignition time. The two parameters should be set according to the welding situation, the higher striking current and the longer duration, the easier ignition. But for sheet welding, the striking current and duration can not be too high and too long, so as not to burn the workpiece. In general, the striking current should be 1.5 times of welding current, and striking time is 0.02~0.05s.
4. External characteristics (Slop)
In order to fit different kinds of electrodes, the MMA welding machine own adjustable
external characteristics curve. Adjust the SLOP to change external characteristics.
CC: constant-current characteristic. Arcing current is constant, independent of the welding voltage. Adapted to acid electrode, basic electrode and groove weld.. 1-20 is decreasing characteristic of adjustable slope, the lower the voltage, the greater the current. 20 represents the voltage drops each 1V, the current increases 20A. Adapted to the cellulose electrodes. CP: Constant power characteristics: Output power (I × V) remains the same, especially for cellulose electrodes.
5. Arc-break adjustment
It is for snapping the arc easily when intermittent welding. It can be set as 30V、40V、50V、
60V,The greater the value, the more difficult to pull off the arc, the parameter should be off
when continuous welding.
6. Anti-sticking function (Felt)
When it is on, it can prevent red and failure electrodes caused by striking. The machine
would stop till the striky electrode is away from workpiece. Then the machine would continue
to work.
7. VRD function (VRD)
There are ON and OFF available for VRD function. When it is ON, the main circuit would not work under welder not welding. Only output less than 12V voltage. It can not only avoid no-load voltage injury, but also save electrical energy, reduce noise and increase the life-span.
32
4.6 Installation, debugging and operation for TIG/PULSE TIG/SPOT TIG.
4.6.1 Installation of the TIG, Pulse TIG, Spot TIG
1. Connect the TIG torch to the Negative output of the welding machine, insert the plug of the torch to the socket of the TIG torch on the front panel, and connect the Air connector of the TIG torch to the Valve seat on the front panel.
2. Connect the earth wire to the positive output, and Clamp the workpiece with the earth clamp.
3. Connect the Inlet nozzle on the back panel and Argon flow meter with air tube, then open the Cylinder valve.
4. Connect the input power wires as figure 4.5 shown, and turn on the power switch. Note: Be ensure that the welder positive and negative output terminals are
connected reliably; otherwise the outputs will be burned due to the heating of
joint!
33
Figure4.5 TIG welding connection diagram
4.6.2 Debugging and operation of TIG/PULSE TIG/SPOT TIG
34
Figure 4.6 TIG welding control panel
Adjust the parameter as following steps 1, 2, 3.
1. Use welding process button to select TIG welding method.
2. Twist knob A to adjust welding current.
3. Select the suitable operation mode by the welding process button.
4. Adjust the gas-flow rate of the cylinder after pressing the gas check button.
5. Start welding
All the parameters in steps 1.2.3 could be saved automatically when the machine is working and
remain the same even if the machine is killed halfway.
There are total 13 adjustable parameters for TIG (DC TIG, PULSE TIG, and SPOT TIG)
1.Current: 2~Rated Current
The welding current of DC TIG and Spot TIG, the peak current of the Pulse TIG, please adjust
the suitable current according to the welding technology.
2. Operation Mode:
TIG operation is the operation mode, which use the torch switch to control the welding current
during working of DC TIG and PULSE TIG. There are 5 ways for TIG welding, including 2T, 4T,
Knob A Knob M
welding process
PULSE
TIG SPOT
TIG
TIG
35
S2T, S4T and Spot Welding, The TIG welding ways should be selected according to the
technical requirements and the operation habit of the operator.
method operation mode TIG torch switch & Current Curve
2T
①Press the on/off button, arc strike and upslope ②Loose the on/off button, down slop and arc quench ③If press the on/off button again before arc quenching, it will continue up sloping to the settled parameter, and turn to ②
4T
① Press the on/off button, arc strike and upslope ②Re-press the on/off button, down slop and arc quench
S2T
① Press the on/off button, arc strike and upslope to initial current HotI ②Last Hott time, then down slope to the set current ③Loose the on/off button, down slop to end current EndI ④Last Endt time, then quench arc
S4T
① Press the on/off button, arc strike and upslope to initial current HotI ② Loose the on/off button, down slop to set current ③Re-press the on/off button ,down slop to end current EndI ④Loose the on/off button, quench arc
Spot welding
① Press the on/off button, strike arc to set value ②Last spot time, quench arc.
sptt
Note: graphic means pressing on/off button of the TIG torch, means loosing the on/off
button of the TIG torch, means pressing the on/off button once (press, then loose)
Table 4.1 the operation mode of TIG welding
36
3.Upslope time(SLPU): 0~15s
The upslope time means the time, which the current from 0 to set current, it should be set
according to the technological requirements
4.Downslope time(SLPD):0~15s
The downslope time means the time, which the current from the set current to 0, it should be
set according to the technological requirements
5. Arc strike mode(HF): the welder provide two arc strike modes including lift (HF) arc strike and
contact arc strike.
6.End current(EndI):0~200%, it means the percent of the set current, it is used for filling the
crater.
7.Initial current(HotI):0~200%, it means the percent of the set current.
The initial current is the current after arc ignition; it should be set according to the
technological requirements. The higher initial current, the easier arc striking, but it is not suggest
to use when welding the sheet metal. Otherwise, it will burn out the workpiece easily. After
ignition arc under some operation mode, the current should keep the init ial current, in order to
heat up the workpiece or lighting.
8. Initial time (Hott): it means the last time of the initial current, it is only valid in the S2T.
9. End time (Endt): it means the duration of the end current, it is only valid in the S2T.
10.Spot time: 0.1~2s
Spot welding time is the time of the SPOT TIG; it should be confirmed according to the
technological requirements.
11. Base current: it is the base current of the PULSE TIG, the peak current is the set current
12. Duty ratio: it is the ratio of the peak time and cycle in the Pulse TIG.
13. Frequency: it is the frequency of the pulse TIG. These three parameters are for the PULSE
TIG only, see the diagram below:
Figure 4-9 Current curve of PULSE TIG
In the figure the I1 is initial current, IB is base current, IP is peak current(set current), I2 is end
current. T1 is upslope time, T2 is downslope time. TP is the duration of the peak current, TB is
37
the duration of the base current, TP+TB is the pulse cycle, the pulse frequency is the c reciprocal
of the cycle: 1/(TP+TB), the duty ratio is the percentage of the duration of peak current in the
pulse cycle: 100*TP/(TP+TB), changing the pulse frequency and duty ratio could adjust the TP
and TB value.
4.7 Installation, debugging and operation for MIG/PULSE MIG/DOUBLE PULSE
MIG.
4.7.1The installation of MIG, PULSE MIG&DOUBLE PULSE MIG 1. Connect the combined cable to the positive output of the welder and the socket of control cable, and the other sides connect to the wire feeder. 2. Connect the earth cable to the negative output of the welder, and clamp the workpiece with the earth clamp. 3. Please insert the power line of the gas heater into the socket of heater power on the back panel, if use CO2 regulator. 4. Insert the gas tube to the air inlet of the wire feeder, the other side to the Vacuum meter of the gas cylinder 5. Connect the power line according to figure 4.5, turn on the switch. After finishing the above work, the MIG welding is done now, put on the welding wire
according to the instruction of wire feeder and welding torch in chapter 8, connect the
power, close the breaker on the back panel, adjust the welding parameters, open the gas
valve then start welding.
38
Figure 4.7 Connection diagram of the MIG welding
4.7.2 The debugging and operation of MIG, PULSE MIG&DOUBLE PULSE MIG
Press welding process button to choose (MIG, PULSE MIG or double pulse mig), then
adjust the other parameters.
39
Figure4.8 Control panel of MIG welding
The adjustable parameter of MIG welding and PULSE MIG welding
1. Current, wire feed speed and thickness: these three parameters are linked, if you adjust one of them, the others will be matched automatically due to there is a Highly intelligent expert database in welding machine.The user just need to select the welding process, operation mode, type of material, wire diameter and any one of (current, wire speed, thickness), the machine will find the best combinated parameters from the expert database.
2. Arc length: the standard arc length in the expert database is (=0), the user could increase or decrease the arc length according to the welding technology.
3. Inductance/arc force: the standard inductance in the expert database is 0, the user could
increase or decrease the inductance/arc force. And the inductance perform different
functions in different welding methods.
MIG/MAG: <0: Get hard and steady arc, =0: medium arc, >0: soft arc, small splash
Pulse MIG: <0: Reduce the droplet transfer force, =0: medium droplet transfer
force,>0:increase the droplet transfer force
4. Type of material: the user could select the suitable type of material according to the base
metal dand welding wire, details in section 4.10 (expert database of MIG, PULSE MIG, &
DOUBLE PULSE MIG).
5. Wire diameter: setting the diameter directly according to the actual used welding wire.
6. Operation mode: there are 5 kinds of torch operation mode as following diagram:
Knob A Knob M
MIG PULSE MIG DOUBLE
PULSE MIG
40
Note: Arrow means press the on/off button of gun, means loose the on/off button,
means press on the on/off button. Figure 4.9 2T Operation mode
Note: Arrow means press the on/off button of gun, means loose the on/off button. Figure 4.10 4T Operation mode
41
Figure 4.11 S2T Operation mode
Note: Arrow means press the on/off button of gun, means loose the on/off button,
mean press on the on/off button. Figure 4.12 S4T Operation mode
42
Note: Arrow means press the on/off button of gun, means loose the on/off button.
Figure 4.13 Spot Welding operation mode
7. End current(EndI): as figures shown, its function is to fill the crater.
8. Initial current(HotI) : as figures shown, its function is to increase the heat input when start to
weld and avoid the welding defects during the arc strike.
9. Burn time: it is to adjust the effect of ball cutting when finish welding.
10. Spot time(Sptt): the duration of the spot welding.
11. Initial time(Hott): the duration of the initial current, it is only suitable for S2T.
12. End time(Endt): the duration of the end current, it is only suitable for S2T.
13. Slop time(SLOP): the switching time between two currents, such as the initial current and
welding current.
14. Double pulse frequency (Freq): as figures shown
15. The arc length of double pulse (AL2): as figures shown, it is the High arc length value of the
double pulse MIG, The lowe arc length decided by corresponding arc in the indicator lamp I
16. The scope of the double pulse(Fd2) , as 4.17 figures shown, it is the rangeability of wire
speed for double pulse.
43
Note: Arrow means press the on/off button of gun, means loose the on/off button,
mean press on the on/off button. Figure 4.14Diagram of Double pulse MIG
4.8 The details of expert database for MIG, Pulse MIG and double pulse MIG
Serial
No.
material AWS
specification Protective gas
welding
machine
series
1 Steel:G 3/4 Si 1 CO2% F,G,H,J
2 AlMg4,5Mg ER5083 Ar+50%He H
3 AlSi 5 ER4043 Ar 100% F,G,H,J
4 AlMg 5 ER5356 Ar 100% F,G,H,J
5 Al99.5 ER1050 Ar 100% F,G,H,J
6 AlSi12 ER4047 Ar 100% H
7 CuAl 9 ER Cu Al Ar 100% F,G,H,J
8 CuSi 3 ER Cu Si Ar 100% F,G,H,J
9 NiCr 21 Mo 9 Nb ER NiCrMo Ar 100% H
10 CrNi 18 8 6 ER307 Ar 97.5% CO2 2.5% F,G,H,J
11 CrNi19 9 ER308 Ar 97.5% CO2 2.5% F,G,H,J
12 CrNi 22 12 ER 309 Ar 97.5% CO2 2.5% H
44
13 CrNi 25 20 ER 310 Ar 97.5% CO2 2.5% H
14 CrNi 19 12 3 ER 316 Ar 97.5% CO2 2.5% H
15 CrNi 13 4 ER 410 Ar 97.5% CO2 2.5% H
16 CrNb 16 ER 430 Ar 97.5% CO2 2.5% H
17 CrNi 22 9 ER 2209 Ar 82% CO2 18% H
18 CrNi 19 12 3 ER 316 Ar 82% CO2 18% H
19 CrNi 13 4 ER 410 Ar 82% CO2 18% H
20 CrNi Flux cored Ar 82% CO2 18% F,G,H,J
21 Rutil Flux cored Ar 82% CO2 18% F,G,H,J
22 Basic Flux cored Ar 82% CO2 18% F,G,H,J
23 Metal Flux core Ar 82% CO2 18% F,G,H,J
24 Steel:G 3/4 Si 1 Ar 82% CO2 18% F,G,H,J
25 Hard facing Ar 82% CO2 18% H Table 4.2 the details of expert database
4.9 Installation, debugging and operation of Carbon Arc gouging
Figure 4.15 The connection of carbon arc gouging diagram As figure 4.18 shown
45
1. Connect the earth cable to the negative output of the welding machine. 2. Connect the torch to the positive output of the welding machine, and connect the compressed air. 3. Connect the power line and turn on the switch
Figure 4.16 control panel of carbon arc gouging
Select the Carbon arc gouging, adjust the current, turn on the compressed air, then start to
work.
4.10 Alarming
When the welding machine is over heating, it would stop and display “Over Temp”, as figure 4.20 shown. The “Over Temp” would disappear and resume to work after cooling.
Figure 4.17 Over-heating alarm(welder temperature is higher than set temperature value)
Knob A Knob M
carbon arc
airair
46
Figure 4.18 Over-current alarm(welder primary current is too large)
Figure 4.19 the master control panel data is uninitialized(The procedure of master control panel is uninitialized)
Figure 4.20 No water alarm(water-cycling system is failure)
Figure 4.21 Lack phase alarm(Three phase input voltage lack phase)
Figure 4.22 Over-voltage alarm(three phase input voltage is too high)
47
Figure 4.23 Low-voltage alarm(three phase input voltage is too low)
Figure 4.27 Over-current of the wire feeder alarm(the resistance of the wire feeder is too high)
5. Upgrade software and add functions
5.1 software upgrade
It is the most important advantage that the software can be upgraded for digital welding machines. And the welding performance can be improved, add and change the function by upgrading software. It is very easy to operate. The steps are as following:
1. Insert the USB of UT-850 to computer, another side to the welding machine.
2. Turn on the computer and welding machine. 3. Run the rjsj4. exe in the computer as following(a~k). a, Double click “rjsj4”
55
a, Long press this button and turn on the switch.
b, Press the , Make it on “More”
c, Twist the button on the left. You will find Pas 1, Pas 2,Pas 3, Pas4.(See below pictures)
56
d, Twist the button on the right to make the numbers the same as the codes.
e, Press the button again. The screen would show “Finished”. Turn off the switch. Note: The softdog and password need to buy from sellers. Please contact the vendor.
57
6. Care and Maintenance
Caution! 1.Do not open the welder case except for professional electrician. 2. Please turn off the welding machine and cut the power before you open the case.
Warning! A n e le c t r i c sho ck ma y be hu r t ev en
f a ta l .
Do not touch the electrified device. Please turn off the welding machine and cut the power before you open
the case.
Note! 转 Turning fan may hurt your body.
Do not close to the turning fan blade. Fix the case before starting up.
1
2
Do not place the welder under the blazing sun for quite a long time. Don’t place the welder under the blazing sun when it is working.
Do not place the welder in the rain. Do not use or deposit the machines in moist environment.。
3
4
nsure that the ventilation holes are not
covered when the welder is working. Welding machines should be used and
Stored in drafty condition
Open the case every six months at least, clean the inside dust and swarf by dry compressed air cleaning machine or vacuum cleaner.
58
Make regular inspection for all insulation sleeves, repair or replace new one if damaged.
Make regular inspection for all electric connection parts, and fastening the loose parts. Please take care of all equipments in case they are damaged Open the case by professional electrician. When maintaining the welder, the users must dismantle the 3-phase cable from
distribution box.
59
7. Overall wiring diagram
Diagram 7.1 Overall wiring diagram
60
60
8. Instruction of wire feeder
8.1 General remarks
NSA-60 is a closed digital wire feeder, it has speed feedback closed-loop control, can ensure veracity and stationary of wire feed speed, the current and voltage can be adjusted with welding machine at the same time, also the actual current and voltage can be showed on display anytime. It is widely used for the welding of carbon steel, aluminum, copper, stainless steel and flux-cored wire
8.2 Technical data
Model and specifications of motor: 24V, 22m, 5A wire-wound motor Voltage of solenoid valve: DC 24V Range of wire feed speed: 1.5m/min~22m/min Adaptable wire diameter: φ0.8、φ1.0、φ1.2、φ1.6 Adaptable wire reel: diameter of axle: φ50 maximum outside diameter: φ300
width: 103 maximum weight: 20kg Size: length* width * height 485mm×200mm×280mm Net weight: 10.5kg
8.3 Install the Wire feeder
According to the MIG welding connection, connect air tube, control cable and welding cable reliably, also can choose extended cable of 10m, 15m, 20m to extend welding range.
Note: 1.The wire feeder cannot be moved by drag welding gun, cable and air tube.
2. Please turn off the valve when connecting the air tube or do not welding.
Warning: when gas is aspirating continuously in the bad environment, asphyxia maybe
caused by oxygen deficit.
8.4 Installation of welding wire
1. Open the shroud, uplift the hand shank of pressure wire steel. 2. Confirm whether the inlet nozzle adapt for the welding wire, plastic nozzle for aluminum wire, steel nozzle for steel welding wire. 3. Confirm whether the guide wire tube suitable for welding wire, steel guide wire tube for steel welding wire, take off the steel guide wire tube when using aluminum wire, instead by Teflon wire tube or carbon fiber tube. Confirm whether the wire feed rolls suitable for welding wire, U rolls for aluminum welding wire, V rolls for steel and stainless steel welding wire.
61
61
After installation, keep wire feed rolls (groove), inlet nozzle, middle nozzle, utter nozzle in a
straight line.
4. Install the wire reel, install the wire reel on wire reel axis,assemble the catch of wire reel axis, tighten up the screw of handle. 5. Across the welding wire through inlet nozzle, middle nozzle, utter nozzle in order, then reaching to the welding torch. When installing the welding wire, please avoid the welding wire pop up to injury people. 6. Reset the antifriction bearing wheel and pressure regulating handle, exert pressing force, pressing force can be adjusted by turn the handle. When the wire is not slipped, please decrease pressing force. 7. Switch on the power supply, press the “checking wire button on wire feeder, inch the wire feed by manual operation, until 15-20mm wire revealed in the head of torch. Contact tube can be removed when necessary, fix it again after the wire crossing out. Note: wire feed speed cannot be too quick by manual operation, or thin welding wire will be bending easily. Warning: don’t close to contact tube to check whether welding wire is outing. Please cut off the power source after using machine.
8.5 The maintenance and overhaul of welding torch and wire feeder
Warning: the maintenance and overhaul must be conducted under the condition of shut off the distribution box and ensure security. Otherwise, it may cause some major accident such as electric shock, burn and run over. In order to make the most advantage of the machine, to ensure safe and normal operation, the daily maintenance and overhaul is very important. Daily maintenance and overhaul should focus on the abrade and deformation of some spare parts in the welding torch & wire feeder, also the blocking of diverter, do the cleaning and changing when necessary. The part and point need to be examined successively are as follows: Parts for
check the contents for check remarks
Welding torch
nozzles
Whether the installation is firm, the front-end deformation
The reason for causing gas hole
Whether the splash is adhering
The reason of welding torch burning out(the effective method is to use Anti-spatter compound)
Contact tip Whether the installation is firm,
The reason for the damage of welding torch’s thread
The condition of the tip damage, abrasion and blocking of the hole
The reason of Arc unstable or breaking
62
62
Wire feeding hose
Size of wire feeding hose
Short wire feeding hose may lead to wire feeding unstable (select the suitable wire feeder hose to replace)
Whether the wire diameter fit for the inner diameter of wire feed hose
Do not coincide is the cause to unstable arc
Dirt inside the hose, blocking of welding wire residue
May lead to bad wire feeding and unstable arc (clean or change new wire feeding hose)
Partial buckling May lead to bad wire feeding and unstable arc( renew new wire feeding hose)
Damage of wire feeder hose Replace new hose Abrasion of the o-circle Renew
Wire feeder
Pressure regulating handle
Over pressure(damage the welding wire) Wire feeding and electric arc unstable
Wire enter hose Wire guiding hose Wire output hose
Weather fit the welding wire or not( distinguish aluminum wire and steel wire)
Produce chip & scrap, abnormal abrasion of wire enter hose Wire feeding and electric arc unstable
Whether the hose center fit for groove center of wire feeder rolls
Dislocation may cause the production of chip & scrap and unstable electric arc
Whether powder and sweeps stocked in nozzle
Clear chip & scrap, sweeps, find out the reason then exclude it
Wire feed rolls
Whether the welding wire diameter fit for nominal diameter of wire feeder rolls
Result in the production of powder, blocking of wire feed hose and unstable electric arc An exception happened, replace with a new one
Groove of wire feed rolls blocked or not
Antifriction bearing rolls
Damaged or not Result in wire feed and electric arc unstable
cable Whether the connection is reliable and firm
The insulation part is broken or not If there’s disconnection or not
Prevent leakage, ensure safety
Diagram 5.1 maintenance and overhaul of welding torch and wire feeder
63
63
8.6 Exception of early diagnosis
When some abnormal phenomena happened, such as unable to weld, unstable electric arc and bad welding performance don’t make the judgment of fault earlier. Sometimes, the welding machine is work normally, but some external reasons may cause above problems. For example, fusing of fuse tube, tight parts come loose, forget switch, setting wrong parameters, disconnected cable, tracheal rupture and effect of base metal’s surface etc. Before you make the judgment of fault and repair, please first check it, most problems can be solved easily. Regarding the welding torch and wire feeder, please check and maintain according to the diagram.
Diagram 5.2 initial diagnosis of abnormal welding Abnormal items Overhaul parts and repair items
can not ignite the arc
Shield
gas can
not flow out
Do not send w
ire
Igniting the
arc hardly
Arc not stable
Weld edge unclean
Adhesive base metal
and welding w
ire
Adhesive welding w
ire and contact tip
Appear gas hole
Wire feeder
Too tight or loose of pressure regulation handle
Powder stored in the nozzle of wire guide tube Abrasion and blocking of wire feed rolls
●
●
●
●
●
Welding
torch
Too large bending of welding torch cable Adaptability, abrasion, blocking and deformation of contact tip and wire feed tube
●
●
●
●
loose of contact tip, nozzle and nozzle’s joint Bad insertion and fastening of welding gun’s joint
●
●
Disconnected welding torch cable and switch control cable(flexural fatigue, crushing)
● ● ● ● ●
64
64
9.Welding machine structure diagram
9.1 Joint A series welding machine structure diagram
Diagram 9.1 welding machine structure diagram (1)
65
65
Diagram 9.1 welding machine structure diagram (2)
66
66
Diagram 9.1 welding machine structure diagram (3)
67
67
9.2Combined welding achinestructure diagram
Diagram 9.2 combined welding machine structure diagram
68
68
9.3 Installation of combined welding machine
Diagram 9.3 installation diagram of combined welding machine
Installation steps 1. Fix water cooler to trolley through connecting piece II. 2. Fix power source to trolley through connecting piece I. 3. Fix the trolley connection plate and wire feeder support plate through the screw. 4. Fix the wire feeder to cone.
69
69
9.4 Water cooling structure diagram
Figure9.4 Water cooling structure diagram
70
70
9.5 Wire feeder structure diagram
Diagram 9.5 wire feeder structure diagram
71
71
9.6 Spare parts code list
Table 9.1 Spare parts name code list
Number
Spare parts number
Spare parts name
Number
Spare parts number
Spare parts name
1 03.03.0008 toroidal transformer 41 350201 magnet ring
2 02.03.0131 commutation inductance
42 350203 magnet ring
3 backboard 43 0377021 membrane switch 4 290031 44 0379000 power socket 5 290032 center septum 中心隔 45 0379002 aviation plug with base 6 290036 paster 贴纸 46 0379006 power socket 7 290037 front display panel 47 0379014 aviation plug 8 290038 middle board 48 0379040 aviation plug
9 290039 magnet ting II back-up plate
49 0379051 fast plug(red)
10 290041 back-up plate 50 0379052 fast plug (black) 11 290044 upper cover plate 51 0040301 shunt 12 290045 discharger base plate 52 0004113 NYL 13 290046 back-wheel support
53 0460012 power line 14 290047 axis 54 0490000 coil 15 290048 base plate of diode 55 0490001 coil
16 290049 antenna connector 56 0860055 master control board of 500F
17 290050 side metal plate 57 9900003 plastic panel 18 290051 support of breaker 58 B000028 500semi-finished diode 19 290052 back metal plate 59 B500F01 syntonic inductance 20 290053 front metal plate 60 B500F02 500Fdriver board 21 290056 upper cover plate 61 B500F07 500Freactor
22 290057 4-star electrical support
62 B500F12 filter inductance
23 290058 back display board 63 B500F09 input current common mode choke
24 290063 Accessories of wire feeder support plate
64 B000054 PCB 4 board
25 290067 sensor platen 65 B833003 PCB 3 board 26 0291000 breaker 66 B500F05 generator transformer
27 292001 magnet ring I back-up
67 FF75R12RT4
IGBT
72
72
28 292004 fan support 68 920054 temperature controller
29 292010 magnet ring II back-up
69 0600001 components of base board
30 292022 IGBT radiator 70 0600002 inside insulation board
31 0293002 fuse 71 0600003 wire plate fixed components
32 294003 fuse base 72 0600004 welding torch flapper
33 0293004 fuse 73 0600005 front cover
34 0293005 fuse base 74 0600006 left cover components
35 2930011 main transformer bracket
75 0600007 right cover
36 294003 air cock base 76 0600008 inside riser 37 0297001 temperature sensor 77 0290000 solenoid valve
38 0303100 3 phase rectifier 78 294003 air cork base
39 342228 diode radiator 79
0350209 magnet
40 0343000 fan 80
0353001 pipe clamp
Continued table 9.1
Num
ber
Spare parts
number Spare parts name
Nu
mb
er
Spare parts
number Spare parts name
81 0353003 pipe joint 114 0800106 nut 82 0353004 pipe joint 115 0800108 nut 83 0354004 PU air tube 116 0890003 rubber gloves
84 0352001 front joint of water tank
117 9100035 handle
85 0352003 joint of water tube 118 BSB5001 remote control board
86 0352004 joint of water tube 119 0004065 right angle strain relief bushing
87 0360302 connector 120 0087001 weld assembly of baseboard
88 0360304 connector 121 0087002 upper cover plate 89 0362002 terminal 122 0087003 inside metal plate
90 0370017 OT terminal 123 0087004 support of kettle fixed
91 0376020 NSA-40knob 124 0087005 motor support 92 0376002 button 125 01000005 kettle 93 0377022 membrane switch 126 01000006 water pump
73
73
94 0379003 nine-core socket 127 0342216 cooling fin
95 0379010 nine-core plug 128 0352001 front joint of water tank
96 0379033 fast plug (black) 129 0353001 pipe clamp 97 0004006 Wire box 130
0372000 4m2 plug reed
98 0004014 Wire axis 131 0376023 rocker
99 0004041 hole plugs 132 0377010 water flow switch
100 0004043 motor 133 0379015 aviation plug( with head)
101 0004048 hole plugs 134 0379019 aviation plug( with head)
102 0004115 hinge 135 0460020 380V power line
103 0460000 cable 136 0650508 screw of 6 flower inside
104 0490003 coil 137 0720510 combined screw 105 0490901 (PEF) 138 9900011 plastic panel
106 0005200 European copper head
139 800201 accessories of
base board
107 0005202 flanged housing 140 800202 accessories of stand board
108 0600305 brass stud 141 800203 axis
109 0600310 screw 142 800204 front-wheel
support 110 0720510 combined screw 143 800205 connect plate 111 0720512 combined screw 144 800206 connector I 112 0800104 nut 145 800207 connector II 113 0800105 nut 146