Laboratory Services
Analytical LaboratoryNew Providence, New Jersey
Chemetall’s Analytical Laboratory provides routine solution and surface analysis, as well as failure mode evaluations, using the latest techniques and instruments to provide detailed performance results.
Equipment and Capabilities
m Scanning Electron Microscope/Energy Dispersive Spectroscopy (SEM/EDS)
m Fourier Transform Infrared Spectroscopy (FTIR)
m Inductively Coupled Plasma (ICP)
m Ion Chromatography (IC)
m High Performance Liquid Chromatography (HPLC)
m Ultraviolet-Visible (UV-Vis) Spectroscopy
m X-Ray Fluorescence (Portaspec)
m Particle Size Analyzer
m Optical Microscopy
m Ion Selective Electrode (ISE)
m Gas Chromatography (GC)
m Total Organic Carbon Analyzer (TOCA)
m Wavelength Dispersive X-Ray Fluoresence (WDXRF)
m Gel Permeation Chromatography (GPC)
Coil LaboratoryNew Providence, New Jersey
Chemetall’s recently upgraded Coil Laboratory features state-of-the-art equipment that is specifically dedicated to support pretreatment, passivation and permanent coating customers in the coil industry.
Equipment and Capabilities
m Multistage Foil Line with Roll Coater
m Coil Washers
m Reverse & Direct Roll Coaters
m Squeegees
m Drawdown Capability for Liquid Paint
m Spray Washers
Metalworking Fluids LaboratoryNew Providence, New Jersey
Chemetall’s Metalworking Fluids Laboratory is equipped with the most currently available testing and analysis equipment to evaluate lubricity, efficacy, solution stability, foam characteristics, coefficient of friction, bio-resistance and compatibility of coolants, lubricants, drawing & stamping compounds, and dry film lubricants.
Equipment and Capabilities
m Micro Tapping Torque Tester
m Interlaken Lubricity Tester
m TurbiScan Emulsion Stability Testing
m Mechanical/Tribology Testing • Ball/Disk on Disk • Four Ball • Three Point Bending • Coefficient of Friction • Twist Compression (TOT)
m Fluid Biostability: HMB, Dip Slides, ATP and Oxygen Respirometer
m Multiple Foam Test Evaluations
m Refractive Index
m Metal Staining and Compatibility
m Tramp Oil Rejection
m Cast Iron Chip Test (CIC)
m Seal Compatibility
Non-destructive Testing (NDT) LaboratoriesLaMirada, California and Toronto, Canada
NDT is performed on process samples in support of Aerospace and other industries that use NDT products. All test methods are in accordance with AMS 2644.
Equipment and Capabilities
m Liquid Penetrant Analysis • Fluorescent Brightness • Comparative Sensitivity • Water Tolerance • Water Content • Removability • Concentration
Physical Testing LaboratoryJackson, Michigan and New Providence, New Jersey
Chemetall’s Physical Testing Laboratory is ISO/IEC 17025:2005 accredited by the A2LA* for physical testing. This facility performs environmental and physical testing of parts, panels, and other components.
Equipment and Capabilities
m CASS (ASTM B368)
m Water Fog (ASTM D1735)
m Salt Spray (ASTM B117)
m MIL-DTL-5541
m Electrical Conductivity Resistance (ECR)
m Hotpacks (Filiform Corrosion)
m X-Ray Fluorescence (Portaspec)
m Bond Durability Testing (APGE)
m Gravelometer
m Cyclic Corrosion Tester (CCT)
m Q-Panel Ultraviolet (QUV)
m Gardometer (Coating Weights)
m Environmental Humidity Chambers
m Cross Hatch, Pencil Hardness, Conical Mandrel, Wet Tape Adhesion
m Cleveland Condensing Cabinets
*Scope of testing certification available at A2LA website: www.A2LA.org.
Technical Service LaboratoriesNew Providence, New Jersey and LaMirada, California
Using a wide range of capabilities, Chemetall’s Technical Services Laboratories test products and simulate process in a controlled environment.
Equipment and Capabilities
m Stationary and Portable Spray Washers
m Powder & Liquid Paint Application
m Vibratory & Mass Finishing Systems
m High Pressure and Steam Wash Units
m Immersion Tanks
Technical Support Call CentersPhone 1 (800) 526 4473, ext. 2355
Email [email protected]
Services
m Consultations
m Product Recommendations
m Troubleshooting
m Titrating Assistance
m General Technical Questions
m Can Also Provide: • Process Control Documents • Technical Information Sheets • Material Safety Data Sheets
(MSDS)
www.ChemetallNA.com • F-18222 - 10/2015 Printed in the USA
Chemetall is proud to serve North America from the following locations:
North American Headquarters675 Central Avenue New Providence, NJ 07974 908-464-6900 Toll-free: 800-526-4473 Fax: 908-464-7914
Chemetall Canada 115 East Drive Bramalea, Ontario L6T 1B7 905-791-1628 Toll-free: 877-311-1471 Fax: 905-791-1459
Chemetall Central Branch 1100 Technology Drive Jackson, MI 49201517-787-4846Toll-free: 877-941-3800Fax: 517-787-5538
Chemetall Mexicana, S.A. de C.V. Avenida El Tepeyac No. 1420-B Parque Industrial O’Donnell-Aeropuerto El Marqués, Querétaro, CP 76250 México52-442-227-2000 52-442-227-2001 Fax: 52-442-227-2002
Chemetall Western Branch 16961 Knott Avenue La Mirada, CA 90638 714-739-2821Toll-free: 800-331-1197 Fax: 714-670-6480
Point 1. Global Specialists Locally Available
Point 2. Comprehensive and Focused Expert Support
Point 3. Integrated Portfolio of Innovative Products
Point 4. High Quality Standards
Point 5. Fast and Accurate Labs
Point 6. Open Collaboration for Efficient Process Performance
Meet Your Needs With Our 6 Point Total Value PropositionChemetall has been innovating, developing, manufacturing and supplying best-in-class Specialty Chemicals for Metal Fabrication and Finishing Processes for over a century. Industries such as aerospace, aluminum finishing, automotive, coil and cold forming have relied on Chemetall’s technologies to achieve their processing needs and requirements. Our approach to chemistry is very special. We support chemical innovation in everything we do and are fully dedicated to the success of our customers!
Cut it. Clean it. Coat it. Control it. Conserve it. with us!®