C8 Instructions
一、C8 System Features
1、32 -65536 level gray scale control, software Gamma correction.
2、Support a variety of point, line, surface light source, supports a variety of rules, shaped handle.
The controller 8 output ports, and each port can be maximum with 1024 lights.
3、You can cascade multiple line control, play content stored in the SD card.
4、C8 store up to 16 files, multiple files sequentially copied to the SD card.
Note:1, C8 single port with load 512 lights, the playback speed of up to 30 frames / sec ports with load more than
512 lights, with a frame rate Increase the number of lights automatically reduced.
二、Support chips:
Support chipsLedctrlSoftware
corresponding model
Single load of
lightsRemark
TM1803,TM1804,TM1809,TM1812 C8-TM 8192 Pixels high and low speed
TM1829 C8-TM1829 8192 Pixels high and low speed
UCS1903,UCS1903B ,UCS1909,UCS1912 C8-UCS256 8192 Pixels high and low speed
UCS2903,UCS2909,UCS2912, C8-UCS256 8192 Pixels high and low speed
UCS6909,UCS6912,UCS7009,UCS5903 C8-UCS32 8192 Pixels
WS2811 C8-WS2811 8192 Pixels high and low speed
INK1003 C8-TM 8192 Pixels high and low speed
TLS3100 C8-TM 8192 Pixels high and low speed
SM16711 C8-SM16711 8192 Pixels high and low speed
SM16716 C8-SM16716 8192 Pixels
SM16726 C8-SM16726 8192 Pixels
LPD6803,D705,1101 C8-6803 8192 Pixels
LPD8806,LPD8809 C8-8806 8192 Pixels
P9813 C8-P9813 8192 Pixels
WS2801,WS2803 C8-WS2801 8192 Pixels
GW6203 C8-TM 8192 Pixels
三、 Meaning on table:
Key Meaning:
AC85-265V power input
POWER Power
Indicator
ERROR Error
indicator
SD SD card slot
TTL Signal (signal 245):
Note:TTL output signal for the controller must be carried out for the land and fixtures (that is, the ground and the output
ground lighting controller connected together.)
四、 Wiring
Key Meaning
SETSave Settings (If you press the SET button, the current settings file and the
playback speed is saved after the next boot still Click to play).
MODE Switching file
SPEED+ AcceleratedPress the SPEED and SPEED-, then enter the file repeat mode
SPEED- Slow down
GND(Ground
cable)
GND(Ground
cable)
DAT data
CLK clock
Note:1、The controller of the lamp when the distance over 30 meters is recommended to use optical isolation signal
transmission control scheme, details, please consult optically isolated signal transmission control program instructions.
2、Wire transmission signal is recommended to use UTP cable for transmission.
五、File Storage:
File Naming Conventions:
The first controller file naming effect:
“00_1.led” ---------The first effect of a first controller
“01_1.led” ---------The second effect of the first controller
“02_1.led” ---------The third effect of the first controller
……
“15_1.led” ---------Article 15 The effect of the first station controller
The second effect file naming station controller:
“00_2.led” ---------The first effect of a second controller
“01_2.led” ---------The second effect of the second controller
“02_2.led” ---------The third effect of the second controller
……
“15_2.led” ---------Article 15 The effect of the second station controller
………
See picture below:
六、Specific parameters:
Memory card:
Type:SD Card
Capacity:128MB—2GB
Format:FAT Format
Storing Files:*.led
Physical parameters:
Operating temperature:-30℃—85℃
Power supply:AC85-265V
Power consumption:1.5W
Weight:0.6Kg With packaging (3pin Terminal * 8; SD card * 1; Power Adapter * 1; Tray * 1)
Signal transmission port type:3pinTerminals
Size:
Note:1、Before you copy files to the SD card, you must format the SD card, note must be formatted before each
copy.
2、SD card must be formatted as "FAT" format.
Note:SD card controller can not be hot-swappable, ie, when each plug SD card, you must disconnect the power
controller.
七、Common Problem:
Problem 1:After power was found C8 error LED error has been flashing, and no effect output
AW:Error LED flashing error has been proved that the controller is not correctly reader, there may
be a problem:
①SD card is blank inside, to no avail file.
②SD card inside the effect file * .led files and controller model does not match the latest software
Ledctrl Inside the correct selection controller model, and re-create the effect of file * .led.
③Before the effect of copy files to the SD card is not formatted as FAT kinds.
④Replace the SD card before testing, SD card bad exclude the possibility.
Problem 2:After the controller is powered, normal light, but no effect lighting changes
AW:The reasons for this are the following:
①Check the lighting signal line and the controller is not connected properly.
②If it is connected to TTL signals, lamps and controllers must be common ground that the lamp
GND GND (ground) and to the controller (ground) tied together.
③Please check the files in SD card * effect when .led selected model and whether current lighting
used consistent chip.
Problem 3:After controller connected to the lamp . Lamps Strobe.
Aw:①The GND between the controller and lamp have not connected。
②The effect of your SD card which is wrong. Select the effect of doing the actual lighting fixtures
chip and chip match.
③Lamps insufficient supply voltage.
Problem 4:SD card can not be formatted.
AW:①First, confirm that the SD card on the side of the protection switch has been unlocked. Unlocking
direction SD card lilies this end.
②Protection lock has been designed according to the requirements, but still can not be formatted,
if this is the case the majority of SD card reader is broken, replace the SD card reading device.
③As the above actions do not solve formatting problems, replace the SD card, re-test.