BATTERY THERMALMANAGEMENT SOLUTIONS
THERMAL MANAGEMENT SOLUTIONS
for ENERGY STORAGE SYSTEMS.
HOTSTART’s Thermal Management System
(TMS) features an intelligent design integrating
proven technologies. Liquid cooling and heating
assists in preventing thermal runaway while
maximizing battery performance during both
charge and discharge cycles.
I N C R E A S E O V E R A L LB AT T E R Y L I F E
M A X I M I Z E C H A R G I N G A N DD I S C H A R G I N G C Y C L E S
M A I N TA I N P E R F O R M A N C EI N VA R I O U S E N V I R O N M E N T S
H E L P P R E V E N T T H E R M A L R U N A W AY A N D F I R E R I S K
I N C R E A S E O V E R A L LB AT T E R Y L I F E
M A X I M I Z E C H A R G I N G A N DD I S C H A R G I N G C Y C L E S
M A I N TA I N P E R F O R M A N C EI N VA R I O U S E N V I R O N M E N T S
H E L P P R E V E N T T H E R M A L R U N A W AY A N D F I R E R I S K
I N C R E A S E O V E R A L LB AT T E R Y L I F E
M A X I M I Z E C H A R G I N G A N DD I S C H A R G I N G C Y C L E S
M A I N TA I N P E R F O R M A N C EI N VA R I O U S E N V I R O N M E N T S
H E L P P R E V E N T T H E R M A L R U N A W AY A N D F I R E R I S K
I N C R E A S E O V E R A L LB AT T E R Y L I F E
M A X I M I Z E C H A R G I N G A N DD I S C H A R G I N G C Y C L E S
M A I N TA I N P E R F O R M A N C EI N VA R I O U S E N V I R O N M E N T S
H E L P P R E V E N T T H E R M A L R U N A W AY A N D F I R E R I S K
[email protected] more information:
FULL CONTROL The system controls go
beyond basic temperature
monitoring and warning.
When fully integrated into
an ESS, the system responds to
temperature requirements, including
charge and discharge battery cycles.
ROBUST THERMAL MANAGEMENTTo maximize battery usage,
either 3500 watts of cooling
power or 1500 watts of heating
power may be applied to the
system’s thermal transfer fluid
reservoir – each TMS unit has
sufficient capacity to support
a typical 250 kW LFP battery
module configuration.*
DIRECT COOLING & HEATINGUtilizing a rack-
mounted manifold
system, efficient,
liquid-based cooling
or heating is directly
delivered to each
battery module.
COMPACT & EFFICIENTDesigned to fit within a standard
server rack, the system may also be
floor-mounted or installed as modular
components to minimize footprint
and maximize output.
THERMAL MANAGEMENT MADE SIMPLE
By harnessing two fluid cycles for chilling and thermal transfer,
HOTSTART’s TMS can quickly deliver efficient cooling and
heating directly to each battery module – optimizing overall
ESS performance.
CHILLING THERMAL TRANSFERSystem
Phase, Hz single-phase (1 Ø), 60 HzVoltage 120 V 240 V
Ingress Protection indoor use only
Thermal Transfer
Fluid Type water/ethylene glycol (50/50 mix)Flow 10 gpm (38 L/min)
Cooling Capacity* 3516 watts (1 ton)Heating Capacity* 1500 watts
*TMS unit capacity designed to support approximately 250 kW LFP battery module configuration. System capacity is dependent on a variety of factors. Consult with HOTSTART for specific custom project requirements.