MELCHOR GABILONDO, S.A.Polígono Industrial Eitua, 6 / 48240 Bérriz (Vizcaya) ESPAÑA / Tel. 94 622 50 90
Intl.: 34-94 622 50 90 / Telefax: 94 622 52 78 / Intl.: 34-94 622 52 78Teléfono Ventas: 94 622 50 30 / Telefax Ventas: 94 682 73 50
E-MAIL: [email protected] / [email protected]: www.mega.es
We have come a long way, but after morethan fifty years our course is still market by thedesire to achieve quality and innovation sothat we can live up to our permanentcommitment to improvement.
We maintain our innovative spirit, high standardsof quality and strict checks of material andprocesses. We are making our tools morepowerful, safer, more operative and longerlasting.
Thus we place our experience in your hands.The high reputation of MEGAabroad has enabled us toconsolidate a firm position onthe markets of all fivecontinents.
Plate laser cutting and weldingfacilities. CEGAMA
Head office and factory of hydraulic components. BERRIZ Painting installation, general warehouses and despatching area. BERRIZ.
Read carefully the safety, user andmaintenance instructions provided withthe equipment. If these basic rules are notfollowed injury to the user, the hydraulicequipment or the load to be lifted mayresult.
Position the cylinder on a solid, evenand horizontal surface.
Never use the cylinder on a slope.
Keep a safe distance from the loadduring operation.
Never position any part of your body underthe load.Always secure the load with mechanicalstands.
Clean couplers before connecting and makesure the connections are securely tightened.
Never exceed the rated capacity of thecylinder.It is strongly recommended the use of agauge to check the pressure.
Prevent hoses from sharp bending and donot drop objects on them.
Never disconnect couplers unless the piston is fully retracted.Always use a safety cock to block the cylinder.
Avoid extreme heat and temperatures over65ºC .
Never use cylinders without a saddle.The saddle helps centre the load.
Never use excessive tightening force thatmay damage the fittings. Do not use tools.
Never use extensions on hand pumps or jacks.Use only the lever provided.
Always use a cylinder of a capacity and hydraulic stroke 25% higher thanthe weight of the load to be lifted.
Use original MEGA oil.
IMPORTANT. An excess of oil will render thepump inoperative.VERY IMPORTANT.- Never use brake fluid.
After use, retract the piston completely, cleanthe equipment and keep it protected fromaggressive environment.
Repair kits are available for every item in thiscalalogue.Always indicate the reference of the item forwhich the kit is intended.
A basic hydraulic configuration consists of a single-acting cylinder, a pumpand a hose. It is really a small machine with the following components:a) Flow generator = Pump. b) Flexible hose to transmit the oil flow from pumpto cylinder. c) Hydraulic cylinder, consisting of a chamber with inlet for theoil and a piston to retain the oil and maintain the pressure that raises or
lowers as the oil changes within the chamber. The pressure iscreated by resistance to flow. This resistance is the result
of a load. This hydraulic equipment can be used invirtually all types of industry. From a basic pump
and cylinder set, you can build manydifferent system configurations by
adding components andaccessories.
1
2
3
4
5
6
7
8
9
10
11
12
CylinderTo raise the load.Page 8
PumpCreates the hydraulic flow.Page 24
HoseTransmits the oil flow.Page 28
A-5507-MMale quick couplerPage 28
A-5507-HFemale quick couplerPage 28
GaugeTo control pressure.Page 29
Gauge adapterTo mount the gauge.Page 29
A-5510Safety valveLocks the load on raised cylinder.Page 30
A-5509Shutoff valveShuts the oil flow and locksthe load on raised cylinder.Page 30
A-5538Safety relief valveAvoids accidental overpressure.Page 30
ManifoldTo distribute the oil flow.Page 31
12 A-5511Male connectorTo connect different components.Page 31
Capacity (kg) Pressure (kg/cm2- psi)
Effectivearea
(cm2 / in2)
Stroke
Volume of oil(cm3/ in3)
Load
Cylindereffective area
Stroke
Oil volumeof cylinder
Oil volumeof pump
Oil volumeof cylinder
Number of cylinders that can be used withone pump.With long hoses, add 35 cm3 for each meterused.
Basic hydraulic calculations for the correct selection of cylinders and pumps.
cm3 / in3cm / incm2
in2
Pressure:
Volume:
Weight:
Area:
Others:
Temperature:
Inches
Please note that the dimensions of this catalogue are exact in the metric system ( mm )and approximate in inches.
8 9
Mounting applications
CSRA SeriesH Y D R A U L I C C Y L I N D E R S
Tilting saddle ( optional )
CSRA-5CSRA-11, CSRA-16CSRA-23, CSRA-31CSRA-55CSRA-93
BCSRA-5BCSRA-11BCSRA-23BCSRA-55BCSRA-93
Ref. Used with
A B C
Dimensions mm/in.
11/167/8
1 7/16
2 13/64
2 7/8
1520232531
19/3225/3229/32
11 7/32
2640556580
1 1/32
1 9/16
2 11/64
2 9/16
3 6/32
17,422,136,35673,5
2575
125175225
2550
100150200250
2550
100150200250
2550
100150200250
50150200
50100150
50150
12 15/16
4 15/16
6 7/88 7/8
12
3 15/16
5 15/16
7 7/89 7/8
12
3 15/16
5 15/16
7 7/89 7/8
12
3 15/16
5 1 5/16
7 7/89 7/8
25 15/16
7 7/82
3 15/16
5 15/16
23 15/16
CSRA-5ACSRA-5BCSRA-5CCSRA-5DCSRA-5E
CSRA-11ACSRA-11BCSRA-11CCSRA-11DCSRA-11ECSRA-11FCSRA-16ACSRA-16BCSRA-16CCSRA-16DCSRA-16ECSRA-16FCSRA-23ACSRA-23BCSRA-23CCSRA-23DCSRA-23ECSRA-23FCSRA-31BCSRA-31DCSRA-31ECSRA-55BCSRA-55CCSRA-55DCSRA-93BCSRA-93D
5
11
16
23
31
55
93
Rate
dca
paci
ty
Ref. Stroke Maximumcapacity
Effective area
tnA
kN cm2 in2 B B1 C C1 D E F G H I L M N R cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
J K
B1, C1 with tilting saddle
lbs.mm. in.185490
126162
4080
160240320400
60120240360480600
83166332498664830220660880392784
1176664
1992
1,13,35,57,79,92,454,99,75
14,6519,524,4
3,657,3
14,652229,336,6
5,0510,120,230,440,550,613,440,353,723,947,871,840,5
121,6
2,23,24,25,66,55,36,48,6
10,813,215,4
7,69,15
12,215,41922,312,81519,724,528,734,224,236,8433645,455,871,2
108,7
702 3/4
702 3/4
702 3/4
702 3/4
702 3/4
702 3/4
702 3/4
20 25/32
20 25/32
20 25/32
20 25/32
371 7/16
20 25/32
471 27/32
1 1/2-16UN
2 1/4-14UNS
2 3/4-16UN
3 5/16-12UNS
3 5/16-12UNS
5-12UN
6 7/8-12UN
29 1 9/64
271 1/16
301 3/16
491 15/16
512
451 25/32
501 31/32
16 5/8
17 11/16
17 11/16
25 1
25 1
6 15/64
6 15/64
10 25/64
10 25/64
10 25/64
2 6/64
26/64
1/4-20UNC
5/16-18UNC
3/8-16UNC
1/2-13UNC
----
1/2-13UNC
----
401 9/16
602 11/32
702 3/4
853 11/32
1003 15/16
1305 1/64
1756 7/8
301 3/16
451 49/64
552 11/64
652 9/16
752 61/64
1003 15/16
1305 1/8
261 1/32
391 17/32
461 13/16
542 1/8
57,152 1/4
803 6/32
1054 9/64
3/4-16UNF
1-8UNC
1-8UNC
1 1/2-16UN
1 1/2-16UN
----
----
25 63/64
401 9/16
481 7/8
592 5/16
----
953 3/4
----
125175227288339139164214264318368144169220272329382163188239290347398219319369194244294221321
4 15/16
6 7/88 15/16
11 5/16
13 11/32
5 1/26 7/16
9 7/16
10 3/812 1/214 1/25 11/16
65/88 11/16
10 11/16
1316
6 7/16
7 3/89 7/16
11 7/16
13 11/16
15 11/16
8 5/812 9/16
14 1/27 5/89 5/8
11 9/16
8 11/16
12 5/8
150250352463564164214314414518618169219320422529632188238339440547648269469569244344444271471
5 7/89 7/8
13 7/818 1/422 3/16
6 7/16
8 7/16
12 3/816 5/16
20 3/824 5/16
6 11/16
8 5/812 5/816 5/820 7/824 7/87 3/89 3/8
13 5/16
17 5/16
21 1/225 1/210 5/818 7/16
22 3/89 5/8
13 9/16
17 1/210 11/16
18 9/16
135235337448549144194294394498598149199300402509612165215316417524625244444544219319419240440
5 5/16
9 1/413 1/417 5/821 5/85 11/16
7 5/811 9/16
15 1/219 5/823 1/25 7/87 7/8
11 13/16
15 7/820
24 1/64
6 1/28 1/2
12 7/16
16 3/820 5/814 5/89 5/8
17 1/221 3/88 5/8
12 9/16
16 1/29 7/16
17 5/16
110160212273324119144194244298348124149200252309362140165216267324375194294344169219269190290
4 11/32
6 15/16
8 3/810 3/412 3/44 11/16
5 11/16
7 5/89 5/8
11 3/413 3/44 7/85 7/87 7/8
9 15/16
12 6/32
14 1/45 1/26 1/28 1/2
10 1/212 3/414 3/47 5/8
11 9/16
13 9/16
6 5/88 5/8
10 5/87 1/2
11 7/16
48,5
109,1
163
227,7
303,1
539
910,9
11,451,922,482,942,42,93,94,9673,454,155,5578,6
10,15,86,88,95
11,11315,51116,719,515,920,625,332,349,3
7,06
15,9
23,75
33,08
44,18
78,54
132,73
1,09
2,46
3,68
5,12
6,84
12,17
20,57
----
----
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a salt bath nitriding treatmentor a hard chrome plating, depending on themodel, to resist corrosion and for longer life.
With built-in bronze guide for easier slidingof piston.
These cylinders are fitted with a removablegrooved saddle, pressure mounted or screwedin the piston head. They are also equippedwith a high flow female quick coupler withdust cap, ref. A-5507-H.
Carry handles on models weighing from20 kg/44 lbs to 40 kg/88 lbs. Heavier modelsare fitted with eye hooks for transport.
With mounting holes and threaded areasprotected against blows for easy coupling orspecial tooling applications.
Cross section view
Single-acting, spring return
10 11
Coupling applications
CCCT SeriesH Y D R A U L I C C Y L I N D E R S
CC: PUSHINGCT: PULLING
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have an induction hardeningtreatment or a salt bath nitriding processdepending on the model.
Each ram is equipped with a female quickcoupler with air dust cap, ref. A-5507-H.
With mounting holes and protectedthreaded areas against possible blows foreasy coupling or special tooling applications.
Unlike the pushing cylinders, the pullingrams retract toward the base to applypressure.
These pushing and pulling cylinders canbe original components of the MaintenanceKits described on page 35.
Cross section view ( CC )
CC-5 SERIESCC-10 SERIESCC-20 SERIES
A-5142A-5042A-5242
Ref. Used with
A B C
Dimensions mm/in.
1 17/64
2 7/82 29/32
81012
5/1625/6415/32
M26 x 2M42 x 2,5M60 x 2,5
325474
Grooved saddle ( optional )
CC-5ACC-5BCC-10ACC-10BCC-20ACC-20BCT-2,5CT-5CT-10
5
10
20
2,5510
Rate
dca
paci
ty
Ref. Maximumcapacity
Effective area
tn kN cm2 in2 B B1 C C1 D E G I J K N O P V cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
L M lbs.409273
19614136854
103199
2,445,614,45
11,968,6
22,463,296,28
12,14
34,95,39,6
12,12,258,6
17,6
M26 x 2
M42 x 2,5
M60 x 2,5
M26 x 2M42 x 2,5M60 x 2,5
70 2 3/4
70 2 3/4
70 2 3/4------------
1,352,22,44,355,5
102,253,98
50115
50135
50130127138138
24 1/2
25 5/16
25 1/8
55 7/16
5 7/16
55
99,6
194
29,151,199
8,04
14,52
28,27
4,247,45
14,41
1,24
2,25
4,38
0,651,152,23
177284191332216364270311318
6 15/16
11 3/16
7 1/213 1/16
8 1/214 5/16
10 5/812 1/412 1/2
184292201342228376------------
7 5/16
11 1/27 15/16
13 7/16
914 13/16
------------
227399241467266494397449456
8 15/16
15 11/16
9 1/218 3/810 1/219 7/16
15 5/817 11/16
17 15/16
235407251477278506---------
9 1/416
9 7/818 3/4
10 15/16
19 15/16
---------
Stroke
Amm. in.
M26 x 2
M42 x 2,5
M60 x 2,5
M26 x 2M42 x 2,5M60 x 2,5
45
60
79
456079
M38 x 1,5
M56 x 2
M84 x 2
M38 x 1,5M56 x 2M84 x 2
----
----
----
707070
2 3/42 3/42 3/4
----
----
----
707070
2 3/42 3/42 3/4
------------
333038354440
1 5/16
1 3/16
1 1/21 3/81 3/41 9/16
B1, C1 with tilting saddle
1 49/64
2 11/32
3 1/8
1 49/64
2 11/32
3 1/8
32
43
60
324360
1 1/4
1 11/16
2 11/32
1 1/41 11/16
2 3/8
22
36
48
243535
7/8
1 7/16
1 7/8
15/16
1 3/81 3/8
20
26
30
212427
13/16
1 1/32
1 3/16
1 13/1615/16
1 1/16
18
21
23
162121
11/16
13/16
7/8
5/813/1613/16
Cross section view ( CT )
CC-5, CT-2,5 SERIES
CC-10, CT-5 SERIES
CC-20, CT-10 SERIES
A-5188A-5189A-5088A-5089A-5288A-5289
Ref. Used with
A B C
Dimensions mm/in.
1
1
1 3/16
20
20
20
25/32
25/32
25/32
18
18
18
23/32
23/32
23/32
25
25
30
D
M26 x 2
M42 x 2,5
M60 x 2,5
Attachments for pulling andpushing pistons ( optional )
Single-acting, spring return
12 13
General application
CSB SeriesH Y D R A U L I C C Y L I N D E R S
Ideal for a wide range of applications incivil engineering, heavy fabrication,construction, maintenance and lifting ofvery heavy loads.
385050505050
150150250150250150250
1 1/222222
5 15/16
5 15/16
9 7/85 15/16
9 7/85 15/16
9 7/8
CSB-11ACSB-23BCSB-31BCSB-55BCSB-93BCSB-200BCSB-200DCSB-300DCSB-300FCSB-400DCSB-400FCSB-500DCSB-500F
1123315593
200
300
400
500
Rate
dca
paci
ty
Ref. Stroke Maximumcapacity
Effective area
tnA
kN cm2 in2 B B1 C C1 D E F R cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
J K
B1, C1 with tilting saddle
lbs.mm. in.60
166220392664
141742526506
108438780
146331096018265
3,6610,113,423,940,586,5
259,6397,2662536894669
1115
4,81115,228,444
156210403515570710755935
123140147163160269369436546459569488598
4 7/85 1/2
5 13/16
6 7/16
6 5/16
10 5/814 1/217 3/16
21 1/218 1/16
22 3/819 3/16
23 9/16
161190197213210319519586796609819638848
6 5/16
7 1/27 3/48 3/88 1/4
12 9/16
20 7/16
23 1/16
31 5/16
2432 1/425 1/833 3/8
147174175188180269469521731531741550760
5 13/16
6 7/86 7/87 7/16
7 1/16
10 5/818 7/16
20 1/228 13/16
20 7/829 3/16
21 5/829 15/16
109124125138130219319371481381491400510
4 5/16
4 7/84 15/16
5 7/16
5 1/88 5/8
12 9/16
14 9/16
18 15/16
1519 5/16
15 3/420 1/16
109,1227,7303,1539910,9
1945,8
2976,5
4017,1
5014
2,256,9
12,92070,895,3
183234259322343424
15,933,1844,1878,54
132,73
283,52
433,73
585,35
730,6
2,465,146,84
12,1720,57
43,95
67,24
90,75
113,27
2 11/32
3 3/83 15/16
5 1/86 7/16
9 9/16
11 7/8
13 3/4
15 7/16
6085
100130163
242
302
349
392
1 49/64
2 9/16
2 61/64
3 15/16
5 1/8
7 1/2
9 1/4
10 5/8
12
456575
100130
190
235
270
305
1 17/32
2 1/82 1/43 6/32
4 9/64
5 15/16
6 11/16
8 1/4
9 7/16
395457,1580
105
150
170
210
240
2 3/42 3/42 3/42 3/42 3/4
2 3/4
2 3/4
2 3/4
2 3/4
7070707070
70
70
70
70
15/1615/1615/1615/1615/16
2 7/16
3 1/16
3 7/16
3 9/16
2323232323
62
78
88
91
5/645/645/645/645/64
3/16
3/16
3/16
3/16
22222
5
5
5
5
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a salt bath nitridingtreatment or a hard chrome plating,depending on the model, to resist corrosionand for longer life.
With built-in bronze guide for easier slidingof piston.
These cylinders are fitted with a removablegrooved saddle, pressure mounted orscrewed in the piston head. They are alsoequipped with a female quick couplerwith dust cap, ref. A-5507-H.
Carry handles on models weighing from20 kg/44 lbs to 40 kg/88 lbs Heaviermodels are fitted with eye hooks fortransport.
Cross section view
Tilting saddle ( optional )
CSB-11CSB-23CSB-31CSB-55CSB-93CSB-200CSB-300CSB-400CSB-500
BCSB-11BCSB-23BCSB-31BCSRA-55BCSRA-93BCSB-200BCSB-300BCSB-400BCSB-500
Ref. Used with
A B C
Dimensions mm/in.
1 1/16
1 17/32
1 17/32
2 13/64
2 7/84 7/85 1/86 5/16
7 3/32
141622253150657888
35/645/8
55/64
11 7/32
22 9/16
3 5/64
3 15/32
4055556580
138155185205
1 9/16
2 11/64
2 11/64
2 9/16
3 6/32
5 7/16
6 1/64
7 9/32
8 1/16
2739395673,5
124130160180
Single-acting, load return
14 15
With security lock nut
CSF SeriesH Y D R A U L I C C Y L I N D E R S
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a salt bath nitridingtreatment to resist corrosion.
With built-in bronze guide for easier slidingof piston.
These cylinders are fitted with a removablegrooved saddle, pressure mounted orscrewed in the piston head. They are alsoequipped with a high flow female quickcoupler with dust cap, ref. A-5507-H.
Carry handles on models weighing from 20kg/44 lbs to 40 kg/88 lbs Heavier modelsare fitted with eye hooks for transport.
The mechanical lock of load is effected bya safety lock nut at the piston extensiondesired.
Particularly recommended for foundationssupport in construction, bridge buildingand maintenance of heavy machinery inpublic works or steel industry, speciallywhen load must be kept on hold for longperiods.
The safety lock nut allows disconnectionof the pump and ensure total safetyconditions when operating under the load.
Cross section view
With tilting saddle ( optional )
CSF-31 SERIESCSF-55 SERIESCSF-93 SERIESCSF-200 SERIESCSF-300 SERIESCSF-400 SERIESCSF-500 SERIES
BCSB-31BCSRA-55BCSRA-93BCSB-200BCSB-300BCSB-400BCSB-500
Ref. Used with
A B C
Dimensions mm/in.
1 17/32
2 13/64
2 7/84 7/85 1/86 5/16
7 3/32
22253150657888
55/64
11 7/32
22 9/16
3 5/64
3 15/32
556580
138155185205
2 11/64
2 9/16
3 6/32
5 7/16
6 1/64
7 9/32
8 1/16
395673,5
124130160180
150150150150150250150250150250
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
9 7/85 15/16
9 7/85 15/16
9 7/8
CSF-31DCSF-55DCSF-93DCSF-200DCSF-300DCSF-300FCSF-400DCSF-400FCSF-500DCSF-500F
315593200
300
400
500
Nom
inal
capa
city
Ref. Stroke Maximumcapacity Effective area
tnA
kN cm2 in2 B B1 C C1 D E F R cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
J K
B1, C1 with tilting saddle
lbs.mm. in.660
1176199242526506
108438780
146331096018265
40,371,8
121,6259,6397,2662536894669
1115
294318356424500610528638563673
11 9/16
12 1/214
16 11/16
19 11/16
2420 3/425 1/822 3/16
26 1/2
444468506574650860678888713923
17 1/218 7/16
19 15/16
22 5/825 5/833 7/8
26 11/16
3528 1/16
36 5/16
422443476524585795600810625835
16 5/817 7/16
18 3/420 5/8
2331 5/16
23 5/831 7/824 5/832 7/8
272293326374435545450560475585
10 11/16
11 1/212 13/16
14 3/417 1/821 7/16
17 11/16
2218 11/16
23
303,1539910,9
1945,8
2976,5
4017,1
5014
14,527,256,4
125222269315383427515
44,1878,54
132,73283,52
433,73
585,35
730,6
6,8412,1720,5743,95
67,24
90,75
113,27
3 15/16
5 1/86 7/89 9/16
11 7/8
13 3/4
15 7/16
100130175242
302
349
392
2 61/64
3 15/16
5 1/87 1/2
9 1/4
10 5/8
12
75100130190
235
270
305
TR 2 1/4 x 5TR 80 x 5TR 105 x 5TR 160 x 5
TR 180 x 5
TR 220 x 5
TR 260 x 5
2 3/42 3/42 3/42 3/4
2 3/4
2 3/4
2 3/4
70707070
70
70
70
15/1615/16
1 27/32
2 7/16
3 1/16
3 7/16
3 9/16
23234762
78
88
91
5/645/645/643/16
3/16
3/16
3/16
2225
5
5
5
3260
125275490593695845940
1135
Single-acting, load return
16 17
Flat cylinders
CSE SeriesH Y D R A U L I C C Y L I N D E R S
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a salt bath nitriding treatmentto resist corrosion.
Grooved piston ends make optional groovedsaddle unnecessary.
All are equipped with high flow female quickcouplers with dust cap, ref A-5507-H, exceptmodel CSE-5 fitted with a female quick coupler,ref. A-5506-H.
With mounting holes in the base.
These CSE cylinders have been designedto combine minimum collapsed height withoptimum stroke.
They are suitable for lifting, clamping,levelling or positioning jobs where space istight.
The spring return piston allows easy removalfrom working place.
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a hard chrome platingtreatment to resist corrosion.
Equipped with high flow female quick couplerwith dust cap, ref. A-5507-H and carrying handle.
Designed for pull ing and tensioningapplications, they can be used in thoseoperations where two heavy pieces have to beput one near the other.
They are normally used in industrial assembling,testing, welding operations of plates or heavysteel frame works.
They are fitted with clevis eyes on both endswhich are linked to attachments welded ontothe plates to join or weld.
ABC
X
D W
P
O
3/8 PNT
E F
127150150
55 15/16
5 15/16
CTN-10CTN-30CTN-50
103050
Nom
inal
capa
city
Ref. Stroke Maximumcapacity Effective area
tnA
kN cm2 in2 B C D E F 0 P W X cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
lbs.mm. in.183725
1085
11,1544,366,2
21,148,681,4
625775920
24 9/16
30 1/236 7/32
60100125
2 11/32
3 15/16
4 15/16
85125155
3 11/32
4 15/16
6 1/8
18 11/16
24 9/16
30 5/16
9,622,137
98,95331,8497,2
14,4248,3472,45
2,237,49
11,23
475625770
426280
1 21/32
2 7/16
3 6/32
354044
1 3/81 9/16
1 3/4
707070
2 3/42 3/42 3/4
405060
1 9/16
22 11/32
75100150
2 15/16
3 15/16
5 15/16
CSE-5CSE-11CSE-23CSE-31CSE-55CSE-93
51123315593
Nom
inal
capa
city
Ref. Maximumcapacity Effective area
tn kN cm2 in2 B C D T U cm3 in3 Kg.
Oil volume WeightDimensioes mm/in.
lbs.5
183753
125212
0,772,85,738,2
19,432,8
1,653,857,05
10,520,737,9
0,751,753,24,89,4
17,2
1/47/167/16
15/325/85/8
7,0615,933,0844,1878,54
132,73
1,092,465,126,84
12,1720,57
1 3/81 3/42 1/8
2 11/32
2 27/32
3 15/32
1 19/32
2 3/16
2 9/16
2 27/32
3 15/32
4 3/32
607998
115147180
2 11/32
3 1/83 7/8
4 17/32
5 25/32
7 3/32
Stroke
Amm. in.
13/16
1 1/64
1 9/16
1 13/16
2 7/16
3 1/8
7/81 5/16
1 7/16
1 3/42 5/16
2 15/16
48,5109,1227,7303,1539910,9
202840476280
223437445875
6,51111121616
3444,554607288
40,555,5657288
104
E F H I J K R S30456575
100130
1 3/16
1 49/64
2 9/16
2 61/64
3 15/16
5 1/64
1 1/32
1 17/32
2 1/82 1/43 6/32
4 9/64
1 3/32
1 29/64
22 3/64
2 3/43
7/321/4
23/6423/647/169/16
2 11/32
2 3/42 3/42 3/42 3/42 3/4
11/1615/1615/1615/1615/1615/16
3/643/643/643/643/643/64
1 5/82 13/64
3 1/83 11/16
4 7/86 5/16
26395457,1580
105
283750527076
5,56,699
1114
607070707070
172323232323
41568094
124160
111111
Cross section view
CTN Series
Pulling cylinders
H Y D R A U L I C C Y L I N D E R S
Single-acting, spring-return
Single-acting, spring return
18 19
Double-acting cylinders
CDRACD SeriesH Y D R A U L I C C Y L I N D E R S
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a salt bath nitriding treatmentor a hard chrome plating, depending on themodel, to resist corrosion and for longer life.
With built-in bronze guide for easier slidingof piston.
Fitted with a relief safety valve, ref. A-5538on the piston retract side, to prevent accidentaloverpressure.
These cylinders are fitted with a removablegrooved saddle, pressure mounted or screwedin the piston head. Are also equipped witha high flow female quick coupler with dustcap, ref. A-5507-H.
Carry handles on models weighing from20 kg/44 lbs to 40 kg/88 lbs. Heavier modelsare fitted with eye hooks for transport.
With mounting holes and threaded areasprotected against blows for easy coupling orspecial tooling applications.
The hydraulic force being applied in bothdirections, these cylinders are very solid andused where a precision operation is requiredto move or position loads accurately on theassembly place. Widely demanded in publicworks and big structure manufacture.
*E= Pushing*T= Pulling
Cross section view
CDRA-9CDRA-23, CDRA-31CDRA-55CDRA-93CD-200CD-300CD-400CD-500
BCSRA-11BCSRA-23BCDRA-55BCDRA-93BCSB-200BCSB-300BCSB-400BCSB-500
Ref. Used with
A B C
Dimensions mm/in.
7/81 7/1657/6421/32
4 7/85 1/86 5/16
7 3/32
2023404650657888
25/3229/32
1 9/16
1 13/16
22 9/16
3 5/64
3 15/32
40556580
138155185205
1 9/16
2 11/64
2 9/16
3 6/32
5 7/16
6 1/64
7 9/32
8 1/16
22,136,322,742,2
124130160180
Tilting saddle ( optional )
Hydraulic return
CDRA-9D
CDRA-23D
CDRA-31D
CDRA-55D
CDRA-55F
CDRA-93D
CDRA-93F
CD-200DCD-200FCD-300DCD-300FCD-400DCD-400FCD-500DCD-500F
9
23
31
55
93
200
300
400
500
Nom
inal
capa
city
Ref. Maximumcapacity Effective area
tn kN cm2 in2 B B1 C C1 D E F G J K N O P R cm3 in3
Oil volume WeightDimensions mm/in.
L M lbs.
5,8
10,4
19,8
28,2
37
60,3
77,3
135173210261301373388476
150
150
150
150
250
150
250
150250150250150250150250
5 15/16
5 15/16
5 15/16
5 5/16
9 7/8
5 5/16
9 7/8
5 5/16
9 7/85 5/16
9 7/85 5/16
9 7/85 5/16
9 7/8
285
315
338
321
421
355
455
356456412512417517439539
11 3/16
12 7/16
13 5/16
12 5/8
16 9/16
14
17 7/8
1417 7/816 7/32
20 6/32
16 13/32
20 11/32
17 9/32
21 7/32
305
338
363
361
461
401
501
406506477577495595527627
435
465
488
471
671
505
705
506706562762567767589789
17 1/8
18 5/16
19 7/32
18 17/32
26 13/32
19 7/8
27 3/4
19 15/16
27 3/419 15/16
3022 5/16
30 3/16
23 3/16
31 1/16
455
488
513
511
711
551
751
556756627827645845677877
Stroke
Amm. in.
60
85
100
130
175
242
302
349
392
B1, C1 with tilting saddle
12,564,62
33,1810,2844,1818,55
78,5428,28
132,7346,14
283,52
433,73
585,35
730,6
ETETET
ET
ET
E
E
E
E
86,2431,72
227,770,54
303,1127,3
539194,07
910,9316,6
1945,8----
2976,5----
4017,1----
5014----
ETETET
ET
ET
ETETETET
1,940,715,121,66,842,87
12,174,38
20,577,15
43,95
67,24
90,75
113,27
ETETET
ET
ET
E
E
E
E
12
13 5/16
14 9/32
14 7/32
18 9/64
15 3/4
19 3/4
1610 1/818 3/4
22 11/16
19 1/223 7/16
20 3/424 11/16
17 15/16
19 7/32
20 3/16
20 1/64
28
21 11/16
29 9/16
21 7/829 3/4
24 11/16
32 9/16
25 3/833 1/426 5/834 1/2
2 11/32
3 3/8
3 15/16
5 1/8
6 7/8
9 9/16
11 7/8
13 3/4
15 7/16
40
65
75
100
130
190
235
270
305
1 37/64
2 9/16
2 61/64
3 15/16
5 1/8
7 1/2
9 1/4
10 5/8
12
1 1/4
2 1/8
2 1/4
3 6/32
4 9/64
5 15/16
6 11/16
8 1/4
9 7/16
1 - 8 UNC
1 1/2 - 16 UN
1 1/2 - 16 UN
1 - 12 UNF
1 3/4 - 12 UN
----
----
----
----
70
70
70
70
70
70
70
70
70
2 3/4
2 3/4
2 3/4
2 3/4
2 3/4
2 3/4
2 3/4
2 3/4
2 3/4
23
23
37
23
47
62
78
84
90
15/16
15/16
1 7/16
15/16
1 27/32
2 7/16
3 1/16
3 5/16
3 17/32
2 1/4 - 14 UNS
3 5/16 - 12 UNS
3 5/16 - 12 UNS
5 - 12 UN
6 7/8 - 12 UN
----
----
----
----
----
----
----
----
27
49
49
45
50
1 1/16
1 15/16
1 15/16
1 3/4
2
----
----
----
----
17
25
25
38
50
11/16
1
1
1 1/2
2
47
70
75
65
70
65
82
90
92
1 7/8
2 3/4
2 7/8
2 9/16
2 3/4
2 9/16
3 1/4
3 9/16
3 5/8
113
113
113
113
113
113
113
113
113
4 7/16
4 7/16
4 7/16
4 7/16
4 7/16
4 7/16
4 7/16
4 7/16
4 7/16
6
10
10
15
15
5
5
5
5
ETETETETETETETEEEEEEEE
11,63,23
30,59,46
40,617,171,826
12043,1
121,642,2
202,570,5
260432,739766252587,4
670115
Kg.
15/64
25/64
25/64
19/32
19/32
3/16
3/16
3/16
3/16
ETETETETETETETEEEEEEEE
12,7
22,9
43,5
62
81,4
132,6
170
297380462574662820853
1047
31,8
54
57,15
80
105
150
170
210
240
19053
500155665280
1175425
1965707
1992692
33181154425370886506
108458590
143151096018265
20 21
CSH: Single-acting, spring returnCDH: Double-acting, hydraulic return
CSHCDH SeriesH Y D R A U L I C C Y L I N D E R S
CSH: SINGLE-ACTINGCDH: DOUBLE-ACTING
Working pressure: 700 kg/cm2/10.000 psi.
All pistons have a salt bath nitriding treatmentto resist corrosion.
With built-in bronze guide for easier slidingof piston.
These cylinders are fitted with a removablesaddle, and are also equipped with a highflow female quick coupler with dust cap, ref.A-5507-H.
Carry handles on models weighing from20 kg/44 lbs to 40 kg/88 lbs. Heavier modelsare fitted with eye hooks for transport.
With mounting holes and threaded areas foreasy coupling or special tooling applications.
Fitted with a relief safety valve, ref. A-5538,onthe piston retract side, to prevent accidentaloverpressure.
Hollow piston cylinders
The hollow cylinders can be used for generalapplications of pushing or lifting forces.
Additionally, they feature a centre-holepiston which allows the insertion of a rodor screw, attachable to the threaded saddle,that travels through the cylinder for pullingor pushing operations.
Ideal for tensioning, extracting, gear andpin removal etc.
CSH-12CSH-20CSH-30CSH-60CSH-90CDH-30CDH-60CDH-90
1220306090306090
Nom
inal
capa
city
Ref. Maximumcapacity Effective area
tn kN cm2 in2 B C D P Q cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
lbs.74
140270640
1010638
12651995
4,58,5
16,53961,63977,2
121,8
8,317,628,658,5
14342,272
163
3,88
1326,66519,232,774
1 5/81 7/82 1/2
33
5 15/16
5 15/16
5 15/16
18,0328,8642,5184,34
13342,5184,34
133
2,84,56,6
1320,6
6,61320,6
5 11/16
6 3/47 7/89 5/8
10 11/16
11 11/16
11 7/812 3/16
7 5/16
8 11/16
10 3/812 5/8
13 11/16
17 9/16
17 13/16
18 1/64
7095
110155200110155200
2 3/43 3/44 5/16
6 1/87 7/84 5/16
6 1/87 7/8
Stroke
Amm. in.
4 7/16
4 7/16
4 7/16
49/64
1 3/64
1 19/64
2 1/64
3 1/64
1 19/64
2 1/64
3 1/64
119,3196,6291,7578,8867291,7578,8880
113113113
19,526,53353,5793353,579
145172200245272296302310
186220263321348446452460
E F G H I J K N2 11/64
2 3/43 3/8
4 15/16
6 1/23 3/8
4 15/16
6 1/2
1 23/64
22 7/16
3 45/64
5 3/64
2 7/16
3 45/64
5 3/64
23 1/43 5/85 1/8----3 5/85 1/8----
5/16 - 18 UNC3/8 - 16 UNC3/8 - 16 UNC1/2 - 13 UNC
----3/8 - 16 UNC1/2 - 13 UNC
----
2 3/42 3/42 3/42 3/42 3/42 3/42 3/42 3/4
25/3225/3225/3225/32
1 1/225/3225/32
1 1/2
25/3225/32
7/81
1 3/167/81
1 3/16
38,550,56294
1286294
128
M29 x 1,5M37 x 1,5M46 x 1,5M72 x 1,5M104 x 1,5M46 x 1,5M72 x 1,5M104 x 1,5
50,882,692,1
130,2----92,1
130,2----
7070707070707070
2020222530222530
2020202038202038
4148637676
150150150
557085,72
125165,1
85,72125165,1
O
1 27/32
1 7/82
474850
--------------------
--------------------
Cross section view ( CSH)
CSH-12
CSH-20
CSH-30, CDH-30
CSH-60, CDH-60
CSH-90, CDH-90
BRCSH-12BMCSH-12BRCSH-20BMCSH-20BRCSH-30BMCSH-30BRCSH-60BMCSH-60BMCSH-90
Ref. Used with
A B C
Dimensions mm/in.
1 6/64
1 25/64
1 3/4
2 49/64
27,2
35,2
44,2
70,2
M29 x 15
M37 x 1,5
M46 x 1,5
M72 x 1,5
M104 x 1,5
D3/4 - 16 UNF
----1 - 8 UNC
----1 1/4 - 7 UNC
----1 5/8 - 5 1/2 UNS
--------
38
50
61
93
127
1 1/2
2
2 13/32
3 21/32
5
28
30
32
37
42
1 1/64
1 3/16
1 1/4
1 29/64
1 21/32
Threaded saddle ( optional )Grooved saddle ( optional )
Cross section view ( CDH )
22 23
Load cells
H Y D R A U L I C T O O L S
SH-1
Spring return
Capacity: 1 t
Weight: 3,5kg / 7,7lbs
Fitted with female quick coupler, ref. A-5506-H.
Widely used for spreading operations in tightspaces where a high force is required.
This hydraulic tool is a component of theMaintenance Kits described on page 35.
TDM-10 - 10t
Tension load cell
Designed for measuring applicationsand pull test.
Precision: ± 2,5%.
CDM-10 - 10t
Compression load cell
Widely used as a load cell in presses,clamps etc.
Precision: ± 2,5%.
The THD bolt tensioners feature samecharacteristics as those of the THS series,although they have a double cylinder foruse where space is tight.
Spread cylinder
Working pressure: 1.500 kg/cm2/21.430psi.
A bolt tensioner is a hydraulic hollowcylinder with an internally threadedpiston which is attached into a bolt.
The application of a hydraulic force tothe cylinder stretches the bolt.
The nut can be then tightened withthe aid of a rod inserted in a holepreviously dri l led on the nut.
The supporting ring of the bolttensioner has an opening for an easiertightening operation.
23 /8
31 /8
(9/1
4)
611/16
SH1TDMCDM Series
THSTHD Series
Hydraulic bolt tensioners
H Y D R A U L I C T O O L S
WeightDimensions mm/in.
85/16
85/16
85/16
85/16
1025/64
1025/64
THS-20THS-22THS-24THS-27THS-30THS-33THS-36THS-39THS-42THS-45THS-48THS-52THS-56THS-60THS-64THS-68THS-72THS-76THS-80THS-85THS-90THS-95THS-100
Ref. Stroke Maximumcapacity
Effectivearea
AkN cm2 in2 A Dmm. in.
20222427303336394245485256606468727680859095
100
321,3
692,45
1302,2
2057,6
2642
3638,2
21,853,38
47,127,3
88,5613,73
139,9221,7
179,6627,85
247,438,35
13/167/8
15/16
1 1/16
1 3/16
1 5/16
1 7/16
1 9/16
1 11/16
1 13/16
1 15/16
2 3/64
2 7/32
2 3/82 9/16
2 11/16
2 13/16
33 3/16
3 3/83 9/16
3 3/43 15/16
Metricthread
M-20M-22M-24M-27M-30M-33M-36M-39M-42M-45M-48M-52M-56M-60M-64M-68M-72M-76M-80M-85M-90M-95
M-100
773 3/64
1124 13/32
1536 1/32
1987 13/16
2278 15/16
26310 3/8
A1
722 13/16
1003 15/16
1365 3/8
1877 3/8
2088 3/16
2459 5/8
542 1/8
773 1/32
1024 1/64
1315 6/32
1526
1857 9/32
2329/32
301 3/16
401 9/16
522 3/64
582 5/16
702 3/4
H H1
271 1/16
401 9/16
542 1/8
742 15/16
853 3/8
1024 1/64
L
903 9/16
1044 3/32
1285 3/64
1606 5/16
1867 5/16
2168 1/2
U Kg. lbs.
5,54,443,5
13,212,1119,9
28,627,525,323,157,355,15350,748,582,679,376
125121116
2,521,81,665,554,5
1312,511,510,5262524232237,53634,5575553
WeightDimensions mm/in.
85/16
85/16
85/16
85/16
1025/64
THD-20THD-22THD-24THD-27THD-30THD-33THD-36THD-39THD-42THD-45THD-48THD-52THD-56THD-60THD-64THD-68THD-72THD-76THD-80THD-85
Ref. Stroke Maximumcapacity
Effectivearea
AkN cm2 in2 A Dmm. in.
2022242730333639424548525660646872768085
365,14
779,4
1495,6
2099
2858,5
24,833,85
538,21
101,715,76
142,7322,12
194,3830,13
13/167/8
15/16
1 1/16
1 3/16
1 5/16
1 7/16
1 9/16
1 11/16
1 13/16
1 15/16
2 3/64
2 7/32
2 3/82 9/16
2 11/16
2 13/16
33 3/16
3 3/8
Metricthread
M-20M-22M-24M-27M-30M-33M-36M-39M-42M-45M-48M-52M-56M-60M-64M-68M-72M-76M-80M-85
652 9/16
953 3/4
1305 1/64
1606 19/64
1887 3/8
A1
–
–
–
–
–
522 3/64
752 15/16
963 3/4
1305 1/8
1526
H H1
–
–
–
–
–
L
2278 15/16
26910 19/32
30812 1/8
38615 3/16
42316 5/8
U Kg. lbs.
11108,87,7
24,2222119,45349,646,34388,283,8797772,7
132125119
54,543,5
11109,58,8
2422,52119,54038363533605754
2329/32
301 3/16
401 9/16
522 3/64
582 5/16
(31 /8)
(11
1 /4)
(2 3/8)
THS: Single cylinder / THD: Double cylinder
24 25
BMBKBMD SeriesH Y D R A U L I C P U M P S
BM-04, BM-1, BM-2 and BMPA-1
All are single acting, one-speed hand pumps, and can be used as a portable hydraulic tool or in a fixed position.They can operate both in a horizontal or vertical position. In this case, the pump head should be placed downwards.
Their light weight and small oil volume make them a very useful pump where a quick action is required.
They are fitted with a safety relief valve, factory rated at the maximum working pressure.
BM-3, BMAP-3, BM-6 and BM-12
Single-acting, two-speed hand pumps. The two-stage automatic system allows the operation of both pistonsfor a quick approach of the cylinder to load.
The larger pump piston cuts out when the cylinder activated by the pump is under high pressure.
All fitted with a safety relief valve, factory rated at the maximum working pressure.
BK-05, BK-09
Vertical hand pumps. Single and two-speed.
Fitted with holes in the pump base to be used as a fixed hydraulic tool.
BM-04BM-1BM-2BMAP-1BK-05BKD-09BM-3BMAP-3BM-6BM-12BMD-3BMD-6BMD-12
Ref.Oil flow perstroke
cm3 in3 A B C Kg.
WeightDimensions mm/in.
lbs.
Workingpressure
kg/cm2 psi
Effective oilvolume
cm3 in3 cm3 in3 C’ D G J J’ L M NF H8,58,58,58,58,58,5
I11/3211/3211/3211/3211/3211/32
10000100001000021430100001000010000214301000010000100001000010000
700700700
1500700700700
1500700700700700700
400125020001250
6501100300030006000
1200030006000
12000
–––––0,51,151,11,151,151,151,151,15
24,476,3
12276,339,767,1
183183366732183366732
–––––8
19181919191919
18 1/64
23 7/32
22 7/16
23 7/32
24 5/824 5/827 9/16
27 9/16
27 9/16
27 9/16
27 9/16
27 9/16
27 9/16
55 1/46 1/64
5 5/87 3/32
8 15/16
5 5/16
5 5/16
6 5/811 7/16
5 3/46 5/8
11 7/16
137155175155144233185185185185185185185
5 13/32
6 1/64
6 7/86 1/64
5 11/16
9 3/16
7 9/32
7 9/32
7 9/32
7 9/32
7 9/32
7 9/32
7 9/32
460590570590625625700700700700730730730
127133155142180228135135168290146168290
0,150,150,150,060,150,150,150,070,150,150,150,150,15
2,52,52,51
2,52,52,5
1,152,52,52,52,52,5
17 5/16
2414 13/16
242424
23 7/16
23 7/16
23 7/16
23 7/16
23 7/16
23 7/16
23 7/16
440610630610610610595595595595595595595
1 3/16
1 3/16
1 3/16
1 3/16
5 1/25 1/22 5/82 5/82 5/82 5/8
4 15/16
4 15/16
4 15/16
30303030
140140
67676767
125125125
3/8-18NPT3/8-18NPT3/8-18NPT1/4-19GAS3/8-18NPT3/8-18NPT3/8-18NPT1/4-19GAS3/8-18NPT3/8-18NPT3/8-18NPT3/8-18NPT3/8-18NPT
––––––
3 6/32
3 6/32
5 1/8–
3 6/32
5 1/8–
––––––8080
130–80
130–
––––––
23 7/823 7/8
––
23 7/8––
––––––
607607
––
607––
400600600600600600665665665665665665665
97104140112––
110110110110110110110
3 13/16
4 1/64
5 1/24 7/16
––
4 5/16
4 5/16
4 5/16
4 5/16
4 5/16
4 5/16
4 5/16
33333333––12121010121010
1 5/16
1 5/16
1 5/16
1 5/16
––
15/3215/3225/6425/6415/3225/6425/64
M8x1,25M8x1,25
M6x1–
M8x1,25M6x1
–
9,414,826,515,915,420,930,930,944,155,137,550,761,7
4,256,7
127,279,5
14142025172328
15 3/423 5/823 5/823 5/823 5/823 5/826 3/16
26 3/16
26 3/16
26 3/16
26 3/16
26 3/16
26 3/16
––––––
3 6/32
3 6/32
6 1/211 7/16
3 6/32
6 1/211 7/16
––––––808016529080165290
23 6/32
3 9/16
3 6/32
3 3/43 3/42 9/16
2 9/16
––
2 9/16
––
5080908096966565––
65––
1st stage 2nd stage
Single-acting hand pumps
Vertical pump
Double-acting hydraulic hand pumps
BMD-3, BMD-6 and BMD-12
These are double acting and two-speed hand pumps.
They all feature same technical advantages as the single acting one-speed pumps.
With a safety relief valve, factory rated at the maximum working capacity.
Hydraulic diagram
Hydraulic diagram
Hydraulic diagram
Hydraulic diagram
26 27
NSNAPBKN SeriesH Y D R A U L I C P U M P S
NS-1, NS-21, NS-22 and NAP-3
Single-acting, one-speed air pumps.
Air driven pumps for operation where electric power is not available or dangerous.
With safety relief valve, factory rated at the maximum working pressure.
Once the NS-1, NS-21 and NS-22 air pumps are connected to the air line, press down on the back section of pedal for operation. Descentor pressure release is effected by pressing down on the front section.
WeightDimensions mm/in.
BES-5BES-10BES-20BES-30BED-10BED-20BED-30
Ref. Effective oilvolume
l. Gal. kWkg/cm2 psi.443485615625485615625
1,322,655,37,952,655,37,95
17 7/16
19 3/32
24 3/16
24 5/819 3/32
24 3/16
24 5/8
Workingpressure
700700700700700700700
A B C Kg. lbs.79
106161210106161210
36487395487395
10000100001000010000100001000010000
5102030102030
250255325365255325365
9 7/810
12 3/414 3/8
1012 3/414 3/8
215285325365285325365
8 1/211 1/412 3/414 3/11 1/412 3/414 3/8
48,867
128128
671,281,28
0,81,12,12,11,12,12,1
1390140013901390140013901390
0,5520,7361,4721,4720,7361,4721,472
Power Oil flow
l/min in3/min30,542,779,379,342,779,379,3
0,50,71,31,30,71,31,3
l/min in3/min1st stage 2nd stage
R.p.m.
BKN-09
Manual and air powered pump.
The pneumatic operation allows for afaster movement of the piston.
The manual operation is required forprecision pressing jobs or whencompressed air supply is not available.
Recommended air pressure:
7-10 kg/cm2. / 100-140 psi
Minimum air flow:
270 l./min. / 59,39 gpm
INDISPENSABLE
Important. It is recommended theuse of an air filter-regulator-lubricatorunit with these pumps to resistcorrosion and for longer life.
WeightDimensions mm/in.
NS-1NS-21NS-22NAP-3BKN-09
Ref. Effective oilvolume
cm3 in3 cm3/minkg/cm2 psi.150150150120407
30,576,361
18367,1
5 7/85 7/85 7/84 3/416
Workingpressure
700700225
1500700
A B C Kg. lbs.15,517,616,73318
787,6
158,2
10000100003215
2143010000
5001250100030001100
120120120120140
4 3/44 3/44 3/44 3/45 1/2
440697606800193
17 5/16
27 7/16
23 7/831 1/27 5/8
––––
0,15
––––
2,5
3,053,059,452,63,05
50501554350
Oil flow Oil flow perstroke
in3/min cm3 in3
BESBED SeriesH Y D R A U L I C P U M P S
Air hydraulic pumps Single-acting
Electric pumps BES: single-actingBED: double-acting
Oil to cylinderOil from cylinder
Oil
Air
Pressurebooster
BES-5, BES-10, BES-20 and BES-30: SINGLE-ACTING
BED-5,BED-10, BED-20 and BED-30: DOUBLE ACTING
They have a two-stage, radial pump that provides a working pressure of 700 kg/cm2/10.000psi.
The first stage allows a quick approach of piston to load and the second stage gives theeffective working pressure.
With precision made components, electric power provides improved operation for applicationsrequiring high pressure.
With safety relief valve, factory rated at the maximum working pressure. For a continuousoperation, pressure should not exceed 560 kg/cm2/8.000 psi.
Frequency: 50 Hz.: 220/380 V - 1,5 kW - 2 HP - 1400 rpm.
Frequency: 60 Hz.: 265/460 V - 1,7 kW - 2,3 HP - 1700 rpm.
Hydraulic diagram
The high flow quick couplers allow a fast and safe connection of the different components in the hydraulic applications.
They consist of two halves, oil tight, called male and female, and have dust caps to prevent entry of dirt.
Supplied according to the reference on the chart.
28 29
A C C E S S O R I E S
The references MAP and MCE are high pressureflexible hoses made of a polyester eslastomer tube,reinforced with a braid of polyaramid yarn, a polyesterinterlay, a single braid of carbon steel wire and anouter polyurethane cover.
Minimum burst pressure: 2.800 kg/cm2 / 40.000 psi
MAPS-1,5 flexible hose is made of an innerpolyethylene tube (POM ), with four spiral steel wirebraids and a polyamide cover.
Minimum burst pressure: 4.400 kg/cm2 / 63.800 psi
As an option, the 1,5 m hoses are supplied with aquick coupler included.
The MEC-3 and MEC-6 hoses are specially designedfor operation with electric powered pumps.
The gauges permit the reading of the pressuregenerated by the pump or the force applied by thecylinder, which provides safety of use, avoids damageto the equipment and guarantees longer life.
Precision: ± 2,5%.
The pressure and force are indicated in kg/cm2, psiand tonnes.
Thermoplastic hoses Glycerine gauges
These adapters allow an easy way of fitting the gauge into cylinder or pump.
A-5580GA-5581GA-5582GA-5583GA-5584GA-5585GA-5586GA-5587G
Ref.
CSRA-5/CSRA-11/CSB-11/CSE-5/CSE-11 SERIESCSRA-16/CSRA-23/CSB-23/CSE-23/CDRA-23 SERIESCSRA-31/CSRA-55/CSB-31/CSB-55/CSE-31/CSE-55/CSF-31/CSF-55/CDRA-31/CDRA-55 SERIESCSRA-93/CSB-93/CSE-93/CSF-93/CDRA-93/CSE-31/CSE-55 SERIESCSH-12/CSH-20 SERIESCSH-30/CSH-60/CDH-30/CDH-60 SERIESGENERAL APPLICATIONSUSO GENERAL APPLICATIONS
Used with Interior Connectionthread
5-11 TNS16-23 TNS31-55 TNS
93 TNS12-20 TNS30-60 TNS
0-700 kg/cm2
0-1600 kg/cm2
3/8 GAS3/8 GAS3/8 GAS3/8 GAS3/8 GAS3/8 GAS3/8 GAS1/2 NPT
MAP-06MAP-1MAP-1,5MAP-2MAP-3MAP-6MAPS-1,5MCE-3MCE-6A-5555A-5588A-5559
Ref.
kg/cm2 psi.700700700700700700
1760700700700700
1760
Workingpressure
100001000010000100001000010000255201000010000100001000025520
Interior
Ø mm in.6,46,46,46,46,46,459,89,86,46,45
1/41/41/41/41/41/4
13/163/83/81/41/4
13/16
Interior
m. in.0,611,52361,5361,51,51,5
23,639,45978,8
118236
59118236
595959
Connectionthread
3/8 x 18 NPT3/8 x 18 NPT3/8 x 18 NPT3/8 x 18 NPT3/8 x 18 NPT3/8 x 18 NPT1/4 x 19 GAS3/8 x 18 NPT3/8 x 18 NPT3/8 x 18 NPT3/8 x 18 NPT1/4 x 19 GAS
------------------------------------
A-5507-MA-5506-MA-5537-H
Quickcoupler
Ref.
A-5507
A-5507-M
A-5507-H
A-5506
A-5506-M
A-5506-H
A-5537
A-5537-H
A-5537-M
Refe
renc
ia
CompletecouplerMale quickcouplerFemale quickcouplerCompletecouplerMale quickcouplerFemale quickcouplerCompletecouplerMale quickcouplerFemale quickcoupler
Desc
riptio
n
Characteristics A-5501
A-5558
MGK-15
NAP-3
Ref.
Gaugeadapter
Gaugeadapter
Gaugeadapter plug
Gaugeadapter plug
Desc
riptio
n
Characteristics
kg/cm2 psi.
Workingpressure
700
1500
700
1500
10000
21430
10000
21430
A C C E S S O R I E SCoupling Adapters
MAPMCE Series A Series
A Series A Series
A-5507
Maximum flow: 17 l/min/1.038 in3/min. Pressure: up to 700 kg/cm2/10.000 psi.
A-5506
Maximum flow: 2 l/min/122 in3/min. Pressure: up to 700 kg/cm2/10.000 psi.
A-5537
Maximum flow: 7 l/min/427 in3/min. Pressure: up to 1.500 kg/cm2/21.430 psi.
100(4)
R
13/3231/2
213/16
21/4
31/413/16
35/8
21/16
1 /2 N
PT3 /8
GAS
25
1811/16
13/16
51/8
5/8
55/16
11 /29/32
9 /32
16
On page 7 of this catalogue, instructions are givenfor better information and use of the accessoriesdescribed. Read pages 4 and 5, carefully.
30 31
A C C E S O R I E S
A hydraulic application can be effected through several configurations, some of which are indicated on page 7 of this catalogue.
None of the configurations described could be carried out without the accessories and fittings described.
A-5509 Shutoff valve
Shuts the oil flow. It also locks the load on a raised cylinder.
A-5510 Safety valve
Locks the load on a raised cylinder.
A-5538 Safety relief valve
Avoids accidental overpressure.
A-5583 and A-5574. Manifolds
Although only two manifolds are described in this catalogue,we can manufacture and supply other manifolds with thenumber of ways required
MEGA hydraulic oil
High quality hydraulic oil for the essential parts of the hydraulictools
Indispensable for a continuous or intensive use of the MEGApumps and cylinders.
Delivered in 2 and 5 litre plastic container.
A-5535. 2 litre plastic container
A-5536. 5 litre plastic container
Repair kits
A repair kit is available for every hydraulic item in thiscatalogue.
The reference of the article for which the kit is intendedshould be clearly indicated.
A-5570 Lowering control valve
Prevents sudden lowering of load by producing a resistanceto the oil flow.
A-5583
A-5574
A-5511
A-5579
A-5513
A-5589
A-5512
A-5590
Y-2/1160
A-5591
A-5514
A-5566
Refe
renc
e
Five-waymanifold
Two-waymanifold
Maleconnector
Maleconnector
Mixedconnector
Mixedconnector
Femaleconnector
Femaleconnector
Conedplug
Maleplug
Elbow
Metallplasticwasher
Desc
riptio
n
Characteristics
kg/cm2 psi.
Workingpressure
10000
21430
10000
10000
10000
10000
10000
10000
10000
10000
21430
21430
700
1500
700
700
700
700
700
700
700
700
1500
1500
Valves
A-5509
A-5510
A-5570
A-5538
Refe
renc
e
Shutoff valve
Safety valve
Loweringcontrol valve
Safety relievevalve
Desc
riptio
n
Characteristics
kg/cm2 psi.
Workingpressure
700
700
700
700
10000
10000
10000
10000
A Series
Connectors. Spares
23/18
26/32
311/32
33/8
1 3/4
26/32
213/16
39/161 3/4
33/8
25/8 1
17/16
23/8
1
2
17/8 3/4
17/8 3/4
23/4 7/8
17/8 11/64
15/8 7/8
15/8 7/8
1/21/2 5/16
11/167/16
3 /32
35/64
13/16
45/16
1
45/16 120
3/8 NPT 25
13/16113/16
15/8
41
20
3/8 NPT
3/8
NPT
47
32 33
M A I N T E N A N C E
Rod pullers
The rod end is threaded into the part to be removed.
When used with a bearing pulling attachment, the load to be applied should not exceed2/3 of the nominal capacity of the cylinder.
As an option, we can supply legs of the dimensions indicated.
Bearing cup puller
They are used in combination with the rod pulling sets. Their legs are locatedwith the grip outward for an easy removal of bushings, bearings, oil seals andother parts located in blind holes.
Bearing pulling attachment
These are also used in combination with the rod pull ing sets.
The thickness of the edges have been flattened to permit placing this attachmentbehind the bearing to be pulled out.
Complete puller sets
They consist of a pump, hose,cylinder, three-grip puller, bearingcup puller, double crosshead,bearing pulling attachment screw,screw cap and gauge
Each component can be suppliedseparately.
IF-1IF-2IF-3IF-5
10203050
Nom
inal
capa
city
Ref.
tn102102149149
4 1/64
4 1/64
5 7/85 7/8
2,52,566
153153230230
6 1/64
6 1/64
9 1/16
9 1/16
Kg. lbs.
Weight
5,55,5
13,213,2
3/4 x 16 UNF1 x 8 UNC
1 1/4 x 7 UNC1 5/8 x 5 1/2 UNS
38387676
1 1/21 1/2
33
AMax.
RBMin.
Dimensions mm./in
A-5519A-5502A-5503A-5504
10203050
Nom
inal
capa
city
Ref.
tn117152340350
4 5/86
13 3/813 3/4
2,66,5
2480
20253550
25/32
11 3/8
1 31/32
Kg. lbs.
Weight
5,714,352,9
176,4
5/8 x 185/8 x 181 x 14
1 1/4 x 12
110152255330
4 5/16
610 3/64
3
AMax.
RBMin.
Dimensions mm./in
Grip and rod pullers
Grip pullers
As the G-12 is supplied with the triple crosshead, it may be turn into a three-grip puller withthe addition of one grip.
The rest of the two-grip pullers require a triple crosshead and a leg to become a three-grip puller.
G-12G-22G-32G-52
10203050
Nom
inal
capa
city
Ref.
tn230310400500
9 1/16
12 3/16
15 3/419 11/16
16223685
200270380500
7 7/810 5/8
1519 11/16
Mechanicalset
GM-12GM-22GM-32GM-52
Ref.CSH-12CSH-20CSH-30CSH-60
Ref.
Cylinder
BM-04BM-04BM-04BM-1
Ref.
Pump
Ref.
Hose
Kg. lbs.
Weight
35,348,579,4
187,4
Dimensions mm./in
AMax.
BMax.
A-5555A-5555A-5555A-5555
TF-1TF-2TF-3TF-5
10203050
Nom
inal
capa
city
Ref. Lengthof leg
tn140280305410
5 1/211 1/16
1216 1/8
17244334
A
240325450580
9 7/16
12 13/16
17 11/16
22 13/16
Max.115135200230
4 9/16
5 5/16
7 7/89 1/16
Min.B
5/8 x 185/8 x 181 x 14
1 1/4 x 12
R
180209328504
7 3/32
8 1/412 15/16
19 13/16
mm. in.
Mechanicalset
TFM-1TFM-2TFM-3TFM-4
Ref.CSH-12CSH-20CSH-30CSH-60
Ref.
Cylinder
BM-04BM-04BM-04
BM-1
Ref.
Pump
Ref.
Hose
Kg. lbs.
Weight
37,552,994,8
207,3
Dimensions mm./in
A-5555A-5555A-5555A-5555
Three-grip pullers
The G-13 model is supplied with double crosshead and triple crosshead.
All the other three-grip pullers require one double crosshead to be used as a two-grip puller.
G-13G-23G-33G-53
10203050
Nom
inal
capa
city
Ref.
tn230310400500
9 1/16
12 3/16
15 3/419 11/16
182745
103
200270380500
7 7/810 5/8
1519 11/16
Mechanicalset
GM-13GM-23GM-33GM-53
Ref.CSH-12CSH-20CSH-30CSH-60
Ref.
Cylinder
BM-04BM-04BM-04BM-1
Ref.
Pump
Ref.
Hose
Kg. lbs.
Weight
39,759,599,2
227,1
A-5555A-5555A-5555A-5555
Dimensions mm./in
A BMax. Max.
Weight
EHM-10EHM-20EHM-30EHM-50
Ref. 2-grip
GM-12GM-22GM-32GM-52
Ref.GM-13GM-23GM-33GM-53
Ref.
3-grip
TFM-1TFM-2TFM-3TFM-5
Ref.
Rodpuller
IFM-1IFM-2IFM-3IFM-5
Ref.
Bearing cuppuller
A-5519A-5502A-5503A-5504
Ref.
Bearing cupattachment
CSH-12CSH-20CSH-30CSH-60
Ref.
Cylinder
BM-04BM-04BM-04BM-1
Ref.
Pump
Ref.
Hose
A-5555A-5555A-5555A-5555
Ref.
Gauge
A-5584GA-5584GA-5585GA-5585G
3250
100255
Kg. lbs.70,5
110,2220562
tn10203050
Nom
inal
capa
city
GTFEHM Series
Complete puller sets
35
M A I N T E N A N C E
These kits are the indispensable tool for many hydraulicapplications, specially for rescues and roadside service,spreading, lifting and pulling jobs where hydraulic forceis required.
From a basic set consisting of a pump, hose and cylinder,the components supplied can be easily assembled tobecome the ideal hydraulic tool in spreading, straightening,pulling, pushing lifting and many other applications.
IMPORTANT:
As the cylinders have a higher capacity than the components ofthe kit, specially chains, cylinder toes, tube extensions etc., theyshould never exceed half their nominal capacity when used withthese accessories.
The SH-1 spreader should not be used beyond 1 t. Note that themaximum working load for the chain is : 1t on GC-10 and500 kg on GC-5
All the technical information related to pumps and cylindersof this chart is described on other pages of this catalogue.
34
They are the adequate and safe hydraulictool for any lifting or pushing operation.
The base, pressure cylinder and oil depositform one integral part and provide morestrength and safety to the jacks
Any pressure loads produced by the vehicleaxle tilting are absorbed as the piston nevercomes into contact with the cylinder. thereforethe jack will not be damaged even if thevehicle tilts.
Fitted with a safety relief valve ( optional upto 5 t ).
With hydraulic stroke limitation.
With carry handle for models MG-20 on.
The MGD-50 MGD-100 have two operatingpumps: for approach and operation.
The MGD-100 includes pressure gauge.
All jacks can be manufactured with a gauge,upon request.
The MGT series combines low minimumheight with higher lift because of thetelescopic piston.
Hydraulic Bottle jacks Body repair kits
MG-2MG-3
MG-3-AMG-5MG-8
MG-10MG-12MG-15MG-20MG-25MG-30MG-40MG-50
MGD-50MGD-100
MGS-5MGS-10MGS-15MGS-20MGT-5MGT-8
MGT-12MGT-20
23358
101215202530405050
1005
10152058
1220
Max
imum
capa
city
Ref. Effectivearea
tn cm2 in2 A B C cm3 in3 Kg.
Oil volume WeightDimensions mm/in.
lbs.100105150150150150150150150150150150150150150
706275
105300316326205
3 15/16
4 1/85 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
5 15/16
2 3/42 7/16
2 15/16
4 1/811 13/16
12 7/16
12 13/16
8 1/16
160168210212219219226228234240242246252270300135131150190215235245180
6 5/16
6 5/88 1/4
8 11/32
8 5/88 5/88 7/8
8 15/16
9 7/32
9 7/16
9 1/29 11/16
9 15/16
10 5/811 13/16
5 5/16
5 6/32
5 15/16
7 1/28 1/29 1/49 5/87 3/32
3,85,35,38,04
11,3414,5217,3421,2328,2738,4844,1758,0873,8973,89
165,18,04
14,5221,2328,27
7,0611,3416,628,27
0,590,820,821,261,752,252,683,294,385,966,849
11,4511,4525,6
1,262,253,294,381,11,752,574,38
D5065657575757575757575----------------40304055----------------
22 9/16
2 9/16
2 15/16
2 15/16
2 15/16
2 15/16
2 15/16
2 15/16
2 15/16
2 15/16
----------------
1 9/16
1 3/16
1 9/16
2 3/16
----------------
310338425437444444451453459465467396402420450145223265350515551571385
12 3/16
13 5/16
16 3/417 3/16
17 1/217 1/217 3/4
17 13/16
18 1/16
18 5/16
18 3/815 9/16
15 13/16
16 1/217 3/49 5/88 3/4
10 7/16
13 3/420 9/32
21 11/16
22 1/215 6/32
7085
110160225275340410525740800
1100135013503300
95150250400400750
10501150
4,35,26,79,75
13,7516,7520,75253245,148,867,182,482,4
201,55,89,2
15,324,524,445,864,170,2
3,63,94,255,96,589
11,51515,523,528,540874,35,57,5
108,5
121722
7,98,69,3
111314,317,719,825,33334,151,862,888,2
191,89,5
12,116,52218,726,537,548,5
MGMGSMGT Series GC Series
CYLINDERPULLING CYLINDERFOOT PUMPAIR HYDRAULIC PUMP
CC-5-ACT-2,5BMP-1NS-1
CC-20-ACT-10BMP-1NS-1
CC-10-ACT-5
BMP-1NS-1
Optional components
* The components market with * are different on GC-20-M
PUMPCYLINDERMETAL BOXHOSEEXTENSION TUBE Nº1EXTENSION TUBE Nº2EXTENSION TUBE Nº3RUBBER SADDLESADDLETHREADED CONNECTORV HEADWEDGE HEADFLAT BASEPISTON TOETUBE CONNECTORSEXTENSION TUBE Nº4LOCK PINSSPREADERSLIP LOCK EXTENSIONCHAINCHAIN PLATECLAMP HEADCHAIN YOKESLIP CLAM TOECOLLAR TOE
5 10 20
BM-04CC-5BA-5167A-5541A-5133A-5134A-5135A-5148A-5142A-5138A-5153A-5154A-5155A-5150A-5139A-5136A-5149SH-1
A-5143A-5186A-5157A-5158A-5156A-5151A-5152
30 / 66,1
BM-04CC-10-BA-5067A-5541A-5033A-5034A-5035A-5048A-5042A-5038A-5053A-5054A-5055A-5050A-5039A-5036A-5049SH-1
A-5043A-5086A-5057A-5058A-5056A-5051A-505245/99
BM-04CC-20-BA-5067A-5541A-5233A-5234A-5235
----A-5242A-5238
--------
A-5284*A-5280*A-5239
--------------------------------
A-5252*----
45/99
GC-5-S GC-10-S GC-20-M
References
Capacity in t
123456789
10111213141516171819202122232425
Nº
Description
WEIGHT kg/lbs
Components
5
6
7
1
4
2
3
11
159
1019
20
2214
24
13
25 17
15
816
21
1223
18
The MEGA jacks can be usedhorizontally with the pump downwardas shown in the illustration.
36 37
W O R K S H O P E Q U I P M E N T
Foldable and portable. These cranes require only a smallspace, are quickly foldable, and easily movable thanks to thefixed auxiliary wheels which, made from polyamide, facilitatemanoeuvrability, do not damage garage floors, do not rustand are quiet in operation.
They feature safety relief valve, dead man's principle operation,automatic, lowering control system and hydraulic limitationof stroke.
They included other important features such as a 135ºswivel hydraulic unit to facilitate users' s position andextendable jib with handle to make easy the position of thearm.
The legs on FC-5A and FC-10A have a height of 80 mm tobe used where space is tight.
AA2EGJKLMR Min.R Med.R Max.PSWeight kg / lbs
Dimensions mm/in.
Capacity in kg / lbs
References
FC-5A FC-10A FC-20A
55 1/64
55 1/64
77 9/16
81 7/859
32 1/438 3/16
3 6/32
41 5/16
45 1/449 7/32
18 5/16
17 11/16
6666
89 1/295
66 3/436 13/16
42 3/43 6/32
49 5/855 5/16
6121 7/16
17 3/4
67 3/470 1/292 1/898 7/16
74 13/16
40 3/445 11/16
7 7/850 3/16
55 7/861 13/16
2522 7/6
14001400197020801500
820970
80105011501250
465450
16751675227524161695935
108580
126014051550545450
1720179023402500190010351160
200127514201570
635570
POSITION 1POSITION 2POSITION 3
1102882716
220417641543
330638583638
500400325
1000800700
200017501650
92 / 203 121 / 267 173 / 381
FC Series
Cranes
4. Extendable jib with handle tofacility its position on the liftingarm. With openings whichindicate lifting capacity on eachpoint.
3. Legs of 80 mm minimumheight on FC-5A and FC-10A foruse in areas of very lowclearance.
2 . L i f t ing and lower ingergonomic pump handle, withdead man's principle operation.
1. Swivel hydraulic unit up to135º to facilitates user's positionwith respect to load. Pumpp i s ton sp r ing improvesoperation.
We manufacture a wide range of frame and benchpresses, designed for the application of a highforce. Their compact and functional designintegrates all the hydraulic elements within thechassis, thus ensuring protection in transport andsaving space in the workshop.
They are fitted with workbench adjustable forheight and winch to assist easy and rapid handlingof the work bench , models KSC-15 A and ANexcluded.
The KP-100 is equipped with a double-actinghydraulic cylinder, ref. CDRA-93F. For thisconfiguration we recommend the use of the electricpump, ref. BED-20.
KPD and KP-100 models have two-speed handpump, ref. BKD-09 and BMD-6.
As an option, all KPD models can be equipped witha manual and air powered pump, ref.BKN-09.
A set of two V blocks is included and the legs haveholes to mount the press to the workshop floor.Supplied fully assembled and ready for use.
With pressure gauge and damper, positioned atthe eye level to make for easy reading.
Set of plate, adapter and punches( optional )
A-5552/ 15 for 15t presses.A-5552/ 30 for 30 and 50t presses.Ø 12 - 15/32 Ø 22 - 55/64Ø 16 - 5/8 Ø 25 - 63/64Ø 18 - 45/64 Ø 30 - 1 7/32Ø 20 - 25/32
Presses
KSCKPKPD Series
ABCDEG1 MinimumG2 MaximumR1 Hydraulic strokeR2 Extension strokeR Total strokeM Side strokeWeight kg/lbs
With hand pumpWith manual/air pumpWith electric pump
Dimensions mm/in.
KSC-15A
KSC-15AN
KPD-30A
KPD-30AN
KPD-30AE
KPD-50A
KPD-50AN
KPD-50AE
KP-100
KP-100E
References
Capacity in t
15 30 50 100
23 13/16
16 1/237
4 3/419 11/16
5 7/817 11/16
3 3/42 15/16
6 11/16
----
34 5/825 5/8
69 11/16
5 11/16
27 15/16
6 1/224 7/32
4 3/42 15/16
7 11/16
9 13/16
34 5/825 5/871 1/45 11/16
27 15/16
6 1/224 7/32
4 3/42 15/16
7 11/16
9 13/16
49 7/32
39 3/878 3/4
11 13/16
39 3/85 1/8
36 5/89 13/16
----9 13/16
----
605420940120500150450
9575
170----
880650
1770145710165615120
75195250
880650
1810145710165615120
75195250
125010002000
3001000
130930250----250----
77 / 170 203,5 / 448 239 / 527 939 / 2070
Sliding cylinder along the press headon KPD models.
38 39
W O R S H O P E Q U I P M E N T
Widely used in workshop and industry formaintenance jobs.
They are equipped with dead man's principleoperation, safety relief valve, automatic loweringcontrol system and hydraulic limitation of stroke.
Can be locked at different heights with the safetybolts provided.
With foot pedal for quick approach to load, ME-650 excluded.
Hydraulic lifting tables
CVTCVR Series
MEPME Series
Foot pedal for quick approach to load,ME-650 excluded.
Safety distance between scissors and between thelifting platform and chassis.
For Din 2440 and DIN 2441 GAS pipes
Bending angles up to 180º.
Supplied with tripod stand, wooden cases and thefollowing set of formers:
CVT-2: 1/2” - 3/4” - 1 - 1 1/4” - 1 1/2” and 2”.
CVT-3: 1/2” - 3/4” - 1 - 1 1/4” - 1 1/2” - 2” - 2 1/2”and 3”.
Fitted with retractable bending frames, permanentlymarked, to facilitate easier position of bendingsupports and pipe to bend.
Equipped with safety relief valve and hydrauliclimitation of stroke.
Piston retracts automatically when the release valveis opened.
Complete instructions for use, maintenance andbending jobs are supplied with the machine.
Any bending job can be carried out without physicaleffort thanks to the high force deployed by the
hydraulic unit: 15t on CVT-2 and 20t on CVT-3.
Rail benders
The set consists of pump, hose and cylinder and ismanufactured to bend rails of 20 kg/m and 30 kg/m.
Spring return
Hydraulic pipe benders
Capacity Cylinder
Kg.CVR-25CVR-50
2550
tn
Reference Weight
CSA-25-C----
3851
BM-1BM-1
Pump
Ref.Ref.
Capacity Pipes up to
Kg. lbs.CVT-2CVT-3
1520
tn
Reference Weight
2”3”
7128
157283
1/2”
3/4”
1”
11/4”
11/2”
2” Table wheels fitted with foot protection and brakes.
261
4011/2
12043/4
500 -
1911
/1668
0 - 26
3 /4 ABCDEFWeight kg./lbs.
Dimensions in mm / in
Capacity Kg./lbs.
References
MEP-650 ME-1500 ME-2500
650 650 1200
ME-650 ME-1200
3307 55121500 2500
74,5 / 164 187 / 412
1433 1433 2646
71 / 57 98 / 216 135 / 298
12 9/16
29 3/432 11/16
19 11/16
41 3/422 7/16
8 7/16
25 3/832 11/16
19 11/16
41 3/420 7/8
9 7/833
40 6/32
19 11/16
54 5/16
27 3/16
215645830500
1060530
250840
1020500
1380690
8 1/434 5/840 6/32
19 11/16
54 5/16
27 3/16
11 13/16
34 5/841 3/421 1/4
56 11/16
31 5/16
210880
1020500
1380690
300880
1060540
1440795
3207558305001060570
We also manufacture a great variety of hydraulic lifting equipment for garage and general industry.We have a comprehensive catalogue covering these items which is available upon request or at our website: www.mega.es
Custom-made equipment, featuring characteristics different from those indicated in this catalogue,canbe supplied on request. We also manufacture hydraulic equipment for special applications such astelescopic cylinders, aircraft jacks, shaft propeller hydraulic pullers for use in naval industy etc.
We always have a hydraulic solution for your specific problem.
Technical information to be given with your request.
Cylinder:
Capacity: t Single-acting Telescopic
Stroke: mm Double-acting Compression load cell
Working pressure: bar Safety nut Tension load cell
Quantity: Hollow cylinder Others
Spring return Minimum height: mm
Pulling cylinder Outside diameter: mm
Type of saddle
Note: Other type of equipment not included above will require a sketch.