For R&R of the Rear Sub-Frame Differential metallic bushing on W140, W202, W203, W210
For removing or installing the rear rubber hydraulic mount in the Lower Control Arm on Mercedes W140
For the inner/outer rubber mounts in the Lower Control Arm on Mercedes
, W 170, 202 208, 210
For R&R of the rear rubber hydraulic mount in the Lower Control Arm on Mercedes , W203, 211 220, 171, 209, 215
For R&R of the rear rubber hydraulic mount in the Lower Control arm on Mercedes W210
M210-0043 Rubber Mount Kit M140-1143 Rubber Mount Kit
M129-2142 Rear Bushing Kit
M2810 Installation Kit
M220-0643 Sub-Frame Bushing Kit
For R&R the suspension bushing on the car w/o removing any parts on Mercedes W211
M211-0043 Front Suspension Arm Bushing Kit
For R&R of the rear rubber hydraulic mount in the Lower Control arm on Mercedes W202, W170
M202-0143 Rubber Mount Kit
For R&R the ball joint, without remove any parts (on car).Applicable: (adapters available separately)
Mercedes-Benz W220, W211, W230
M220-0343 Ball Joint Tool Kit
For R&R the ball joint from/to the steering knuckle on Mercedes , WW220, W211 230
M211-0068 Sub-Frame Ball Joint Kit
For R&R the front rubber mount of rear axle assembly on Mercedes-Benz 163/164 chassis
ML1140 ML/RV Suspension Bushing R&R Kit
Rear sub-frame differential mount bushing kit to replace worn out differential mounts from the center of the sub-frame on W124/201
TTS1819 Rear Sub-Frame Kit
Use it to remove and isntall support joints in the wheel carrier on Mercedes
(This tool incorporates an axial bearing, and a pressure piece which guarangtees the correct position of the new metallic bushings when replaced).
W124, 129, 140, 201, 202, 210, 220
M202-0043 Rear Wheel Carrier Set
[email protected] * [email protected]
www.germancartoolsplus.com * 928-234-6349
Strut spring compressor for the MacPherson struts. Designed to fit securely around the spring and protect the spring from damage. (
)Front & Rear
axle springs
TTS1941 Spring Compressor
For TTS1941 Spring Compresssor.Applicable: W203/211
TTS1007 Spring Compressor Jaw Set
For Front and Rear Axle springs on W107, W116, W123, W124, W126, W129, W140, W170, W201, W202,W208, W210, W211, W220, W230 (including 4-matic)
TTS1801 Spring Compressor
For R&R front and rear rubber mounts in rear axle mount on Mercedes-Benz W210
M210-0143 Rear Sub-frame Bushing Kit TTS1389 Front Sub-frame Bushing R&R KitFor R&R the rubber hydraulic mount in the upper and lower control arm, right on the car.Applicable: Mercedes-Benz W203/204/211/212/220/221
Use it to remove or install the rear rubber mounts of the rear axle carrier on Mercedes-Benz W124, W129, W201
M201-1143 Puller
TTS1376 Universal Valve Spring R & R KitReplace valve spring and oil seal of valve rod on car, withoutremoving head gasket. Works great in the narrow engine room.Enormous time saving for replacement of valve stem seals.Special design helps compress valve spring regardless of firewall barrier.Applicable: BMW N42, N52, N62, M54, M52, M56, M60,Mercedes M102, 103, 104, M111, 112, 113, 271, 272
For R&R front and rear rubber mounts in the rear axle mount on Mercedes-Benz W203
M203-1553 Sub-frame Bushing Kit
www.germancartoolsplus.com * 928-234-6349
For splitting track-rod ends, anti-roll bar, ball joints,.... etc., especially in confined space conditions on
(Also applicable on BMW, VW Audi)Mercedes W170, W202, W210, W220
For removal of the track-rodend from the drag link on
(Also applicable on BMW,VW Audi)
Mercedes-Benz type 201, 123, 124, 126, 129..etc
For splitting track-rod ends, anti-roll bar mountings, ball joints on
W210/Mercedes-Benz
W202/ W220
Special design with self-locking nut to remove and installthe torque strut at front axle.Bore size: M14x1.5Applicable: Mercedes W171, W203, W209
Applicable:BMW: E38, E39, E52, E53, E60, E61, E70, E83, E90, E91,E92, R50, R52, R53, RR1, RR2, X5Mercedes: E-Class (W211), CLS (W219), S-Class (W220),SL-Class (W230)Audi: A4, A6 Carrera lower suspension ball jointPorsche: 996
BMW 312-240 Ball Joint Puller Big Kit24 mm, 27mm, 31mm, 36mm
TST1549 Steering Torque Rod Joint Separator
TTS1808-24mm Ball Joint Separator
Scissor type puller allows access to difficult to reach and obstructed ball joints.
TTS1727 Ball Joint Puller
TTS1092-24mm Ball Joint Separator
TTS1083-21mm Ball Joint Separator
For removing and installing front wheel bearings with thespindle on the car Applicable: Mercedes-Benz, BMW, VW/Audi, Porsche,Volvo, toyota/Lexus, Nissan Infinity, Honda/Acura, andother Asian makes,
B90A Front Wheel Bearing and Hub Puller Kit
For removing and installing front and rear wheel bearings on most of the cars
B90K Wheel Bearing Master Kit
Hydraulically driven, this kit quickly pushes the axle out of the hub, and remove the hub.Kit including Hydraulic ram, 4 lug and 5 lug adapters
TTS1089 Universal Heavy Duty HydraulicHub Remover
TTS1446 * M220-0033 Ball Joint SeparatorPuller for track control arm and radius rod at stub axle assembly joints (used with 10 tons hydraulic press foot pump).Applicable: Benz W211 / W221 / W215 / W219 / W220 / W230
www.germancartoolsplus.com * 928-234-6349
Use it to remove fuel sender retainer nut on Mercedes-Benz W202
5 mm pin wrench for R & R lever-type fuel lever sensoron Mercedes W140,210
For holding fan pulley while loosening or tightening screwson viscosity fan coupling on Mercedes-Benz M102, 103, 104 engines
65 mm open end wrench for replacing the radiator fan hub on (6 cylinder),
(6 cylinder 4 valve) (8 cylinder 4 valve), (12 cylinder 4 valve)
engines
Mercedes M103 M104 M119M120
For late models 119, 604Used with fan hub holder # 113-0040
M111, 112,113,
For removing and installing the plastic fuel tank lid on MercedesW204, W207, W212BMW,Volvocars....
For removing the plastic fuel tank lid on Mercedes-Benz
BMW, VW-AudiW211, W203,
For R&R the seal top air suspension strut nut on Mercedes-Benz W220
001 589 0007 00
TTS1399 Fuel Tank Lid WrenchFuel delivery slotted wrench for lock ring on fuel pump/sending unit on Mercedes-Benz M classsW163/W164 from 2005-2011 R class W251
For holding fan pulley while loosening or tightening screwson viscosity fan coupling on M112, 113, 119.985 (1996-2003)
For holding fan pulley while loosening or tightening screws on viscosity fan coupling on M111, OM604, 605, 606
For removing the top seal on the Airmatic air suspension strut on Mercedes-Benz W220
M220-0061 ABS Shock Absorber Service Kit
M900-0007 Strut Nut Socket
M202-0007 Pin Wrench socket
M210-0107 Pin Wrench B-M1550 Fuel Level Sending Unit
M204-212 Fuel Tank Lid Remover
M103-0040 Fan Holding Tool
TST3265/65mm Fan Clutch Wrench
TTS36mm Open End Wrench
M113-0040 Fan Holder
M119-0240 Fan Holder
16mm: Mercedes W220, 210, 203, 221, 211, 204,17mm: Mercedes W124, 140, 170, 126, 201, 202, 210,
Special angel designed to remove the nuts from Benz engine mount
M2186 Engine Mount Wrench Set 16mm, 17mm
For driving in the tulip shaped, flared oil dipstick guide pipe into crankcase on All Mercedes-Benz
M120-0621: For determining oil level and inspection length of dipstick guide tube on Mercedes
103.943/984/985, 104, 111,119, 120, 137, 603, 604, 605, 606, 611, 612, 613, 628,
M120-0721:For measuring oil level and for checking length of oil pipe on M112, 113, 271, 271, 646, 647, 648
M120-0621 * M120-0721 Dipsticks
M111-1231 Support with Handle
M210-0015 Oil Seal Installer (Drift punch)
Spark plug boot wrench for V6 Mercedes-BenzTTS1000 Puller Wrench
To secure retaining ring for ball joint replacement on front and rear axles. Retaining ring is torqued to 300Nm/226 ft/lbs
163 M-Class
M3857 3/4" M-Class Drive Socket
For shaft sealing ring on inside of front axle housing. Model: 210.081/082/282, 211.08/28/09/29 (M111 engines)
www.germancartoolsplus.com * 928-234-6349
For positioning the camshaft in 30 degree TDC positionApplicable: M275, M285 (C for the left bank, A and B for theright bank), M137 (A and B)
To hold down the camshaft (4 pcs set) on Engine: 157, 276, 278
M201-0037 Timing Chain Guide
M104-0037 Timing Chain Guide
38mm wrench:For turning the cam
Holds camshaft in 40 degree TDC position (left/right side).Mercedes-Benz M112, M113
M112-0132 Camshaft Holders with 38 mm Wrench
M276-0140 Cam Timing Kit
TTS4047 Camshaft Timing Kit
M156-0061 Cam Timing Kit
For holding camshaft tight in installation position(25 degree after ignition TDC).Applicable: M111, 119, Om604, 605, 606, 611, 612, 613, 628
M111-0315 Retaining Pins
M271-0140
M271-0061
Timing Chain Retainer for drawing in the timingchain. Retain timing chain with camshaft sprockets in propertiming position.
Camshaft Retaining device makes it possible to position the camshafts in the installed position. This makesit possible to slacken and tighten the bolts attaching thecamshaft gear.
M271-0015
M271-0031Mercedes M271
: Install the plug into the timing case cover (access to chain tensioner)
: For unloading the timing chain tensioning device on
M271-0140 Camshaft Timing Kit
M270-0061 Camshaft Timing KitThis holding device makes possible holding down and fixing of the camshaft. This makes possible to slacken and tighten the bolts attaching the camshaft gear on
Specially designed for vehicles fitted with chain driven 1.6/2.0ldirect injection gasoline engine.Supplied with small and large diameter clamp pieces to ensurethe camshaft is correctly held in place.Supplied with special security bit socket for the camshaft pulleys.Designed to allow removal and assembly of the camshafts.
M133, M270, M274 engines (lateA Class, B Class CLA, C Class and E Class
Use on Mercedes engines in the 2007-present 63 series for servicing the camshaft, timing chain and cylinder head.
M156 AMG V8
The retaining device makes it possible to position the camshafts in the installed position, also for turning, installing/removing the crankshaft pulley. (OEM#: 651589014000, 651589004000, 651589024000. Application: Benz OM 651 Volume 2.0D / 2.2D / 2.5D. Models of car: Benz GLK (W204), Benz CLA 200 CDI, Benz CLA 220 CDI, Benz A Class W176, Benz Sprinter 316CDI OM651.
MBZ1500 Cam Timing Kit
www.germancartoolsplus.com * 928-234-6349
Universal valve spring compressor arm for the R&R valve springs. Use it together with the following pressing devices.on M102, 103, 104, 111, 119, 120, Om601,603, 604, 605, 606
Applicable: M102, 103, Om601, 602, 603,
Applicable: M190E2.3 L 16-V
Use it to support the valve spring compressor.Applicable: M104, 111, 119, 120, Om604, 605, 606
Special angel designed to remove the nuts from engine mount
For M110 Engines
Required to properly service various Mercedes dashboard components without causing undue damage. 8-piece tool kit contains: (2) removal tools for ignition lock on model W126.(2) removal tools for ignition locks on models W124 & W201. (2) removal hooks for instrument cluster on models W107, W116, W123, W124, W126, W140, and W201(2) radio removal tools on models W129, W140, W202, and W210.
For R&R of protective cover for ignition steering lock (from 1992).W123, 124, 126,129, 140, 163, 170, 202, 210, 414
For loosening and tightening the ring (rosette) of the electronic ignition switch on W129, 140, 202(as of June 97), 208, 210, 211, 230, 240, 463
TST1725B Dashboard Service Kit
M202-0014 Turning Tool
M210-0007 (M129-140) Turning Tool
Special design for removing the door panelon W140
TTS140-1663 Panel Wedge
Special Pliers for installing the nylon shift shaft bushings(transmission gear lever rubber) on most Mercedes models.(Also working on BMW, VW-Audi.....)
TTS1333 Bushing Installer
For checking ATF level on 1997 & newer cars 722.6 transm.
For determining oil level on 716.5, 722.7, 722.8 transmission
M140-1521 Transmission Oil Level Dipstick
M168-0121 Transmission Oil Level Dipstick
M111-1861 Universal Valve Spring Compressor Arm
M102-1160 Pressing Device
M102-1063 Pressing Device
M102-103 Post Set
M111-0159 Support Bridge
M110-0461 Valve Spring Compressor Kit
M271 Crankshaft Front Gear Wheel SocketFor removing crankshaft front gear wheel on M271
www.germancartoolsplus.com * 928-234-6349
M900-0059 Ignition Lock SetUse it to release retainers for removal of ignition switch. Applicable: W124, 126, 129, 201
Use to press on external lugs and rivets of dip-type fasteners of simplex and duplex roller chainApplication: Benz Model 615, 616, 617, M102, M103, 116, 272, 272, BMW and SAAB
M5843 Chain Link Press Tool Kit
Designed to prevent damage when assemble the cover tothe crankshaft flange on Benz M271, M272
Guide seal on the cover
Take off the front part, and push the cover into the flange
For R and R the compressor belt on Mercedes-Benz M112, M113, M272, M273
Replaceable bolts
For holding the vibration damper when loosening the bolt on the crankshaft on Mercedes-Benz M112, 113, 137
M112-0040 Holder
TST4727 Compressor Belt Pulley Wrench
M606-0009 Oxygen Sensor Socket
Pressured spring of parking brakeApplicable: All Mercedes models
3/8" Drive 16mm, length 93mm, outer dia: 22mm, spark plugsocket with retaining spring and joint.Applicable: Mercedes M112, 113, 137, 155, 166, 271, 272, 273,275, 902, 906, BMW X6,
TTS1251 16mm Spark Plug Socket
TTS1347 Rear Crankshaft Radial Sealing Ring Installer
M119-0114/651-0161 Front/Rear Crankshaft Radial Seal Installer
½"Drive , T50 Star: for assembling and dismantling the free wheel pulley while changing the alternator or pulley onBOSCH alternators on Mercedes, BMW, Audi,VW...
½ Drive, 10mm 12 point: M271, VW Golf, Vento, Passat,AudiA3, Volvo, VW Jetta with 1.9 L TDI engines
M271-T50 Alternator Pulley Remover
M271-10mm Alternator Pulley Remover
M112-0961 Parking Brake Installer
For US type radiator pressure testers to earlymodel radiators with large cap (all Mercedes-Benzbefore 1968)
M28 Radiator Adapter - Early type
TTS2402-27TTS2402-32TTS2403-36:
TTS2402-76TTS2402-84
TTS2402-86:
TTS2402-86:
TTS2402-108
: 3/8" Dr. 27 mm for (ClassA), 3/8" Dr. 32 mm for 3/8" Dr. 36 mm for
: 3/8" Dr. 76 mm 12 point for : ½" Dr. 84 mm 14 point for
½"Dr. 86 mm 16 point for
86mm, 18 point for
108mm, 15 point for
M163 C230: OM 364, 366,
OM604, 605, 606, M116BMW M52, M60, M62, M70, M73 engines
M102, M103E320 (ML),
(2007-210 Dodge Sprinter) Volvo S40, S60,
S70, S80...(from 1999-2003), BMW(316i, 318i, 2001-onwards)N40, N42, N45,N46 engines
½" VW Golf (MKIII. Tdi, Passat Tdi), Audi A6 TDi, Citroen, Peugeot, Renault,
:
Volvo, Audi...
Volvo
Oil Filter Sockets, for R&R of oil filtercartridge elements
For replace front and rear crankshaft radial sealing ring on Benz M102, M111, M112, M113, M137, M156, M159, M272, M275, M285, M601, M602, M603, M604, M605, M606, M628, M629.
www.germancartoolsplus.com * 928-234-6349
For removal and replacement of the crankshaft bolt on M271M271-0003 Harmonic Balancer Pulley Holder
M271/272/273/642 Crankshaft Hub Locking Kit
Use to fill the 722.9 transmission, along with VW/Audi, BMW, Mercedes,.... other carsTank capacity: 7.5 LiterFlow capacity 75 cc/cycleContains standard fitting 8pcsHose size 3/8" x 4.5 ft.Size 260x 370x 595mmSpecial designed for filling ATF oil. Replaceable fittings for different vehicles. With hand pump for vacuum to prevent oil deterioration.
TTS178A Automatic TransmissionFluid Filler Kit
Used for filling fluids in transmission, differentials and transfer cases (not suitable for use with fuels or solvents).
ATF 101 ATF 102
ATF 103
ATF 104
ATF 105ATF 129
ATF-TOY118
(applicable to Ford)(applicable to BMW, Honda, Nissan
and many other universal applications), ATF 104, ATF 105, ATF 16 DSG and
ATF 17 CVT (applicable to VW/Audi) (Applicable to 1999 and
newer Porsche Models) (Mini Cooper)(applicable to Mercedes
722.9 Transmissions)(applicable to Toyota)
Special adapters for each models available separately or Complete Euro / Asian Kit
Provide with the safety valve helps the pre-setting pressure (43psi (3kg/cm2) relief automatically. Provide with pressure gauge makes read and control the air pressure in the tank easier...
AST722-9 Universal Pneumatic Oil andLiquid Dispenser
TTS1017B 17pcs Diesel Injector Seat Cutter SetTo clean and re-cutting the injector seat of modern common rail diesel engines.
(BMW, Ranult, Ford),
19mm angle reamer for FIAT, Iveco
19mm flat reamer for Bosch injector(BENZ)
Special Open design socket to remove the nut while keepingit away from the air suspension pipe on Mercedes-BenzW211, W221, W164
TTS1318 Air Suspension Piping Socket
For installing clutch piston K1 K2 into external disc carrier transmission722.3, 722.5
8900 Sleeve
For Mercedes-Benz with fuel injection system
TTS160-2 Fuel Line Plug Set
20.0mm to install timing cover with seal in place, preventing damage to the seal. Applicable:M103, 104 March 89 and newer
M103-0114 Sleeve
For Mercedes-Benz M and R and GL Class brake caliperApplicable: W163, W164, W251Dimension: Length 78mm, Hex 9mm
TST2189-9mm, 6 point 1/2" Drive Socket
TST4054 Broken Glow Plug Remover Set
M733/6 Cylinder Head Rail Guide Pin Puller
NST1243 Gearbox Filling Tool Adapter
TTS2167 Star-E Socket SetFor cylinder head bolts on BMW, Mercedes CDI enginesLength - 140 mm, Size: E10, E12, E14, E16, E18, E20
Mercedes-Benz (09-diesel) model: CDI for removing broken glow plugs . Comes with 1/4" 8mm and 10mm taps.(CDI)
Use it to remove pins from the cylinder headon all Mercedes-Benz
For Mercedes W221, 722.9 transm.
www.germancartoolsplus.com * 928-234-6349
Singing Power ProbeTo diagnose more easily than before.The inside of may electrical parts has coil. When the vehiclepower is on the magnetic power starts flow the coil, than the coil becomes magnet in a moment.At this very moment, Singing probe detect a line of magneticforce with beeping and blinking. Just touch the coiled part.Beep & Lights on? That means the part itself has no problem at all.If there is no sound or light on Singing probe, that means the part is not working or the power is off. Can test a various kind of parts:Gasoline injector, Lpi Injector, CRDi Injector, Ignition coil, Solenoid Valve, EGR Valve, ISA Valve Relay Alternator,Motors....etc.. (any parts if it is coiled inside.)
www.germancartoolsplus.com * 928-234-6349
Special designed, to remove the A/C low side coupler onBenz W221, 211, 204, 219
TTS1303 Benz A/C Low Side Coupler Remover
Locks flywheel at starter ring gear from the transmission side on Mercedes-Benz M102, M103, M104, M111, M601, M602, M603, M605, M606, M611, M612, M613
M601-0240 Flywheel Lock
Use to lock crankshaft on starter ring gear (mount in starter hole) for vehicles with left and right hand-steering on Mercedes-Benz M112, M113, M137, 155, 156, 272.979, 273, 629, 642.992,
M112-0340 Flywheel Lock
17mm special wheel lug socket for 1/2"(17mm) 45mm length: Maybach, W221 (S-class and late CL-class which came installed with unique convex lug bolts
W221 engines.
W221 Lug Nut Socket
1/2" Drive, for grooved nut on rear axle shaft flange. Needed when replacing axle bearing or axle seal on 107, 114, 115, 116, 123, 126 chassis with constant velocity joint axles.
M915-0207 Socket
BMW Rear Axle Carrier KitBMW Rear Axle Carrier KitFor R&R the Rear Axle Carrier Mount Bushings w/o completely lowering the rear axle assembly on BMW E39, E46/E85, E53
Base unit
Mercedes-Benz Rear Sub-frame Bushing KitMercedes-Benz Rear Sub-frame Bushing KitFor R&R front and rear rubber mounts in rear axle mount on Mercedes W210
BMW2336-E53: BMWE53/X5 Bush#:33 31 1 770 454BMW2336-E53: BMWE53/X5 Bush#:33 31 1 770 454
E46/E85: BMW E46, E85 Bush#:33 31 092-515/516/517E46/E85: BMW E46, E85 Bush#:33 31 092-515/516/517
E39 Sedanand WagonE39 Sedanand Wagon
MercedesW210MercedesW210
www.germancartoolsplus.com * 928-234-6349