Compact development system rich with on-board peripherals for all-round
multimedia development on dsPIC33FJ256GP710A device.
for dsPIC33®mikromedia™
Page 3
I want to express my thanks to you for being interested in our products and for having
confidence in Mikroelektronika.
The primary aim of our company is to design and produce high quality electronic products
and to constantly improve the performance thereof in order to better suit your needs.
The dsPIC® and Windows® logos and product names are trademarks of Microchip Technology® and Microsoft® in the U.S.A. and other countries.
TO OUR VALUED CUSTOMERS
Nebojsa Matic
General Manager
Page 3
Introduction to mikromedia for dsPIC33® 4
Package Contains 5
Key Features 6
System Specification 7
1. Power supply 8
USB power supply 8
Battery power supply 8
2. dsPIC33FJ256GP710A microcontroller 10
Key microcontroller features 10
3. Programming the microcontroller 11
Programming with mikroBootloader 12
step 1 – Choosing COM port 13
step 2 – Choosing device family 14
step 3 – Choosing device 14
step 4 – Browse for .HEX file 15
step 5 – Set Baud rate 16
step 6 – Uploading .HEX file 16
Programming with mikroProg™ programmer 18
mikroProg Suite™ for PIC Software 19
Programming with ICD2 or ICD3 programmer 20
4. Reset buttons 22
5. Crystal oscillator 24
6. MicroSD Card Slot 25
7. Touch Screen 26
8. Audio Module 28
9. USB-UART connection 30
10. Accelerometer 32
11. Flash Memory 33
12. Pads 34
13. Pinout 35
14. Dimensions 36
15. Mikromedia Accessories 37
16. What’s Next 38
Table of Contents
Page 4 Page 5
Introduction to mikromedia for dsPIC33®
The mikromedia for dsPIC33® is a compact
development system with lots of on-board
peripherals which allow development of devices
with multimedia contents. The central part of
the system is a 16-bit dsPIC33FJ256GP710A microcontroller. The mikromedia for dsPIC33
features integrated modules such as stereo MP3
codec, TFT 320x240 touch screen display,
accelerometer, USB connector, audio connector,
MMC/SD card slot, 8 Mbit flash memory, 2x26
connection pads and other. It comes pre-
programmed with UART bootloader, but can also
be programmed with external programmers,
such as mikroProg™ or ICD2/3. Mikromedia is
compact and slim, and perfectly fits in the palm
of the hand, which makes it convenient platform
for mobile devices.
Page 4 Page 5
Package Contains
Copyright ©2011 Mikroelektronika.
All rights reserved. Mikroelektronika, Mikroelektronika logo and other
Mikroelektronika trademarks are the property of Mikroelektronika.
All other tradmarks are the property of their respective owners.
Unauthorised copying, hiring, renting, public performance and
broadcasting of this DVD prohibited.
20122011 www.mikroe.com
01 02
04 05
03
06
Damage resistant
protective box
mikromedia for dsPIC33®
development system
mikromedia for dsPIC33®
user’s guide
mikromedia for dsPIC33®
schematics
DVD with documentation
and examples
USB cable
for dsPIC33®
mikromedia™
SCHEMATICS
We present you with a complete color schematics for mikromedia™ for dsPIC33® development board. We want you to know what your board is consisted of andhow it actually works.
Page 6 Page 7
Key Features
01
16
02
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Connection Pads
TFT 320x240 display
USB MINI-B connector
CHARGE indication LED
LI-Polymer battery connector
3.5mm headphone connector
Power supply regulator
FTDI chip
Serial Flash memory
RESET button
VS1053 Stereo mp3 coder/decoder
dsPIC33FJ256GP710A microcontroller
Accelerometer
Crystal oscillator
Power indication LED
microSD Card Slot
ICD2/3 connector
mikroProg connector18
17
Page 6 Page 7
System Specification
power supply
Via USB cable (5V DC)
board dimensions
81.2 x 60.5cm (3.19 x 2.38 inch)
weight
~50 g (0.11 lbs)
power consumption
77 mA with erased MCU
(when on-board modules are inactive)
03
06
07
08 09
1110
12
13
14
1516
04 05
17 18
Page 8 Page 9
1. Power supply
You can apply power supply to the board
using MINI-B USB cable provided with
the board. On-board voltage regulators
provide the appropriate voltage levels
to each component of the board. Power LED (GREEN) will indicate the presence of
power supply.
You can also power the board using Li-Polymer battery,
via on-board battery connector. On-board battery charger
circuit MCP73832 enables you to charge the battery
over USB connection. LED diode (RED) will indicate
battery charging. Led is off when battery is full. Charging
current is ~250mA and charging voltage is 4.2V DC.
Battery power supply
USB power supply
Figure 1-1: Connecting USB power supply
Figure 1-2: Connecting Li-Polymer battery
Page 8 Page 9
23
5
4
1
VCC-SYS VCC-3.3
E310uF E4
10uF
R26
2K23
12GND
Vin
Vout
REG1
LD29080DT33
VCC-BAT
D1PMEG3010ER
R443K9
Charging Current approx. 250mA
R394K7
VCC-3.3
E7
10uF
C40
2.2uF
R344K7
R64K7
VCC-BAT
VSENSE
VCC-SYS
VCC-SYS
R4310K
R37
10K
R3610K
VCC-3.3
STAT
R3810K
R451K
VCC-3.3
E510uF
R3510K
VCC-3.3
R494K7
+-
CN1BATT CONN
M1DMP2160UW
STATVSSVBAT VDD
PROG
U5
MCP73832Q4BC846
Q5BC846
C2810nF
FP2FERRITE
12345 GND
IDD+D-VBUS
CN3
USB MINIB
VCC-USB
C29
2.2uF
VCC-3.3
R4622K
E10
10uF
R47120K
VCC-1.8
VCC-1.8
R500R
123
5
4
VinGNDEN ADJ
Vout
U3
MIC5205-ADJ
DAT
A BU
S
LD2CHARGE
LD1POWER
VCC-BAT
1234567891011121314151617181920212223242526
HDR1
M1X26
2728293031323334353637383940414243444546474849505152
HDR2
M1X26
VCC-3.3 VCC-3.3
VCC-SYS
VCC-1.8VREF-1.8
E1110uF
FP3
FERRITE
Figure 1-3: Power supply schematics
Page 10 Page 11
2. dsPIC33FJ256GP710A microcontroller
The mikromedia for dsPIC33® development system comes with
the dsPIC33FJ256GP710A microcontroller. This high-performance
16-bit microcontroller with its integrated modules and in combination
with other on-board modules is ideal for multimedia applications.
Key microcontroller features - Up to 40 MIPS Operation;
- 16-bit architecture;
- 256KB of program memory;
- 30.720 Bytes of RAM memory;
- 85 I/O pins;
- Internal Oscillator 7.37 MHz, 512kHz;
- nanoWatt features: Fast Wake/Fast Control;
- 2-UART, 2-SPI, 2-I2C, 2-CAN;
- DAC, ADC, etc.
Data/Memory Bus
Data Bus
40/60 MIPS 16-bit Core- Optimal for ‘C’- MCU + DSP Resources40-bit
AccumulatorDSP
Engine
16 CoreRegisters
16x16 Multiply
Shadow Set
Instruction Data
MotorControlPWM
32-bitCRC
AudioDAC
ControlDAC
10/12-bitADC
AnalogComparator
I2C
CAN
UART
InputCapture
SPI
OutputCompare
PWM16-bit
Timers RTCCPMP 32-bitQEI
DMA8 Ch.
Flash(256KB)
RAM(30KB) GPIO VREG
2-wireDebugInterrupt
Controller
Page 10 Page 11
The microcontroller can be programmed in three ways:
01
02
03
Over UART bootloader
Using mikroProg™ external programmer
Using ICD2/3 external programmer
3. Programming the microcontroller
Page 12 Page 13
Programming with mikroBootloader
You can program the microcontroller with bootloader which is
pre-programmed into the device by default. To transfer .HEX file
from a PC to MCU you need bootloader software (ds30 Loader)
which can be downloaded from:
After software is downloaded unzip it to desired location and
start ds30 Loader software.
Figure 3-1: ds30 Loader open-source software
Connect mikromedia for dsPIC33® with a PC before
starting ds30 Loader softwareNOTE
http://www.mikroe.com/eng/products/view/586/mikrommb-for-dspic33-board/
Page 12 Page 13
Identifying device COM port
Figure 3-2: Identifying COM port
step 1 – Choosing COM port
Figure 3-3: Selecting COM port
01 From drop down list select USB COM port which is used for communication with a PC (in this case COM5)
In Device Manager you can see which COM port is
assigned to mikromedia (in this case COM5)
01
NOTE
Page 14 Page 15
01 From drop down list select MCU chip (256GP710A)
step 2 – Choosing device family step 3 – Choosing device
Figure 3-4: Selecting MCU family
01 From drop down list select MCU family (dsPIC33FJ)
01
Figure 3-5: Selecting MCU chip
01
Page 14 Page 15
Figure 3-6: Browse for .HEX file
Figure 3-7: Pop-up window for .HEX file choosing
step 4 – Browse for .HEX file
01 Click on Browse button and from pop-up window (figure 3-7)
select .HEX file which will be uploaded to MCU memory
01
03
02
01 Select desired .HEX file
Folder list
Click on Open button03
02
step 3 – Choosing device
01
Page 16 Page 17
step 6 – Uploading .HEX file
Figure 3-9: Write program
01 First RESET mikromedia and then, within 5s click on
Write button
01
Figure 3-8: Seting baud rate
step 5 – Set Baud rate
01 From drop down list set baud rate value to 256000
Check Write program check box02
02 01
Page 16 Page 17
Figure 3-11: Uploading is finishedFigure 3-10: Program uploading
0101First RESET mikromedia and then, within 5s click on
Write button
After uploading is finished you will get notice in
ds30 Loader history window
Progress bar indicates .HEX file upload process
01
01
If you accidently erase bootloader program from MCU memory it is possible to load it again with external programer. mikromedia for dsPIC33® bootloader firmware.hex file is located in Firmware subfolder, Page 12.NOTE
Page 18 Page 19
The microcontroller can be programmed with mikroProg™ programmer and mikroProg Suite™ fo PIC® software. The
mikroProg™ programmer is connected to the development
system via the CN6 connector, Figure 3-12.
mikroProg™ is a
fast USB 2.0 programmer
with mikroICD™ hardware
In-Circuit Debugger. Smart engineering
allows mikroProg™ to support PIC10®,
PIC12®, PIC16®, PIC18®, dsPIC30/33®, PIC24® and
PIC32® devices in a single programmer. It supports over
570 microcontrollers from Microchip®. Outstanding performance,
easy operation and elegant design are it’s key features.
Programming with mikroProg™
programmer
Figure 3-12: Connecting mikroProg™ to mikromedia™
Page 18 Page 19
mikroProg Suite™ for PIC® Software
mikroProg™ programmer requires
special programming software called
mikroProg Suite™ for PIC®. This
software is used for programming
of ALL Microchip® microcontroller
families, including PIC10®, PIC12®,
PIC16®, PIC18®, dsPIC30/33®, PIC24®
and PIC32®. Software has intuitive
interface and SingleClick™ programming
technology. Just by downloading the
latest version of mikroProg Suite™
your programmer is ready to program
new devices. mikroProg Suite™ is
updated regularly, at least four times a
year, so your programmer will be more
and more powerful with each new
release. Figure 3-13: Main Window of mikroProg Suite™ for PIC® programming software
Page 20 Page 21
Figure 3-14:Placing ICD2®
connector
The microcontroller can be also programmed with ICD2® or ICD3® programmer. These programmers connects
with mikromedia board via ICD2 CONNECTOR BOARD.
Programming with
ICD2® or ICD3® programmer
In order to enable the ICD2® and ICD3® programmers to be connected to the
development system, it is necessary to provide the appropriate connector such as the
ICD2 CONNECTOR BOARD. This connector should be first soldered on the CN5 connector.
Then you should plug the ICD2® or ICD3® programmer into it, Figure 3-14.
Figure 3-15: Connecting ICD2®
or ICD3® programmer
Page 20 Page 21
VCC-3.3
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
C8
100nF
VCC-3.3
SOSCOSOSCI
CLKOCLKI
PGD
1PG
C1
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
3151
70
26
25
76
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
MCLR#
VCC-3.312345
CN6
M1X5
MCLR#
PGD1PGC1
MCLR#PGD1PGC1
VCC-3.3
654321
CN5
M1X6R15100
R14100
RB7
RB6
decoupling capacitors
Figure 3-16: ICD2 / ICD3 & mikroProg™ programmer connection schematics
Page 22 Page 23
Board is equipped with two reset buttons. First is located at the back side of the
board (Figure 4-1), and second one is at the top of the front side (Figure 4-2).
If you want to reset the circuit, press either of two buttons. It will generate low
voltage level on microcontroller reset pin (input). In addition,
a reset can be externally provided through pin 27 on
side headers (Figure 4-3).
4. Reset Buttons
Figure 4-2: Frontal reset buttonFigure 4-1: Reset button located at the backside of the board
Page 22 Page 23
Figure 4-3: Reset circuit schematics
R810K
VCC-3.3
C3100nF
T1
R7 100
T2
RST
VCC-3.3
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
SOSCOSOSCI
CLKOCLKI
30292827 343358575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2R
A9/V
ref-RB1
RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
VCC-3.3
2728293031323334353637383940414243444546474849505152
HDR2
M1X26
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
Page 24 Page 25
Board is equipped with 8MHz crystal oscillator (X1) circuit that provides external
clock to the microcontroller OSC pins. This base
frequency is suitable for further clock multipliers and
ideal for generation of necessary USB clock, which ensures
proper operation of bootloader and your custom USB-based
applications. Board also contains 32.768kHz Crystal oscillator (X3) which provides external clock for internal RTCC module.
5. Crystal oscillator
Figure 5-1:Crystal oscillator
module (X1)
VCC-3.3
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
SOSCOSOSCI
CLKOCLKI
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
The use of crystal in all other schematics is implied even if it is purposely left out, because of the schematics clarity.
NOTE :
Figure 5-2:Crystal oscillator schematics
Page 24 Page 25
6. microSD Card Slot
VCC-3.3
R5 27
R4 27
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
MOSI2-RG8
SCK2-RG6
SOSCOSOSCI
CLKOCLKI
SD-C
D#
SD-CS#
MISO2-RG7
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
SD-CS#
R1110K
R1010K
VCC-MMC
R910K
SD-CD#
VCC-MMC
R16
27
VCC-3.3
E610uF
C38100nF
FP1
FERRITE
124567
CD
MOSI2-RG8
SCK2-RG6
MISO2-RG7
VCC-MMC
CSDin+3.3VSCKGNDDout
CD G
CSDin+3.3VSCKGNDDout
CD GN
D
CN4
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
Board contains microSD card slot for using microSD cards
in your projects. It enables you to store large amounts of data
externally, thus saving microcontroller memory. microSD cards
use Serial Peripheral Interface (SPI) for communication with the
microcontroller.
Figure 6-3:Inserting microSD card
Figure 6-1: microSD card slot
Figure 6-2:microSD Card Slot module connection schematics
Page 26 Page 27
The development system features a TFT 320x240 display covered with a resistive
touch panel. Together they form a functional unit called a touch screen. It enables data
to be entered and displayed at the same time. The TFT display is capable of showing
data in 262.144 diffe rent colors.
7. Touch Screen
Figure 7-1: Touch Screen
Page 26 Page 27
VCC-3.3
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
T-D
6T-
D7
PMR
DPM
WR
LCD
-BLE
D
T-D
12T-
D11
T-D
10
T-D
9T-
D8
T-D5T-D4T-D3T-D2
SOSCOSOSCI
CLKOCLKI
LCD
-RS
LCD
-YU
LCD
-XL
LCD
-YD
LCD
-XR
T-D
1
LCD-RST
LCD-CS#
T-D0
T-D15T-D14T-D13
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 772423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
7131
51
70
26
2576
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2R
B15
RB1
4
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCCVC
C
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
R23
1K
VCC-SYS
VCC-3.3
E1310uF
R2510K
VCC-3.3
R2410K
LCD-RSTLCD-CS#
VCC-3.3
LCD-BLEDR4012
VCC-SYSD2
BAT43
LED-A12
DB1715
HSYNC12
RD35
VSYNC11
WR/SCL36
LED-A23
LED-A34
LED-A45
IM06
ENABLE14
IM17
IM28
IM39
DOTCLK13
GND43
SDO33
RESET10
RS37
CS38
FMARK39
VCC-IO40
XR44
YD45
XL46
SDI34
LED-K1
YU47
DB1616
DB1517
DB1418
DB1319
DB1220
DB1121
DB1022
DB923
DB824
DB725
DB626
DB527
DB428
DB329
DB230
DB131
DB032
VCC41
VCC-I42
TFT1
MI0283QT2
VCC-3.3
LCD-YULCD-XL
Q3BC846
Q2BC846
Q1BC846
C22
18nF
R42300K
C21
18nF
R41300K
LCD-RST
LCD-RSLCD-CS#
LCD-YULCD-XLLCD-YDLCD-XR
PMRDPMWR
VCC-3.3 VCC-3.3
T-D5T-D6T-D7
T-D4
T-D8T-D9T-D10T-D11T-D12T-D13T-D14T-D15
T-D3T-D2T-D1T-D0
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
Figure 7-2: Touch Screen connection schematics
Page 28 Page 29
Figure 8-2: Inserting 3.5mm headphones jack
The mikromedia for dsPIC33 features stereo audio codec VS1053. This module
enables audio reproduction by using stereo headphones connected to the
system via a 3.5mm connector CN2. All functions of this module are controlled
by the microcontroller over Serial Peripheral Interface (SPI).
8. Audio Module
Figure 8-1: On-board VS1053
MP3 codec
Page 28 Page 29
Figure 8-3: Audio module connection schematics
VCC-3.3
R5 27
R4 27
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
MOSI2-RG8
SCK2-RG6
MP3
-DCS
MP3
-CS#
MP3
-RST
#
MP3
-DR
EQ
SOSCOSOSCI
CLKOCLKI
MISO2-RG7
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A8182838485868788899091929394959697989910
0
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5R
D14
RD
15RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GNDVC
AP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
MP3-CS#
C2022pF
C1922pF
C11100nF
R1 1M
R2010K
R21
10K
MP3
-DR
EQ
MP3-RST#
C10100nF
C4100nF
C12100nF
C9100nF
R210K
R1910K
C23100nF
VCC-3.3
C24100nF
VCC-3.3
C26100nF
VCC-3.3 VCC-3.3
C27100nF
X2
12.288MHzC131uF
VCC-3.3
GPI
O
VCC-3.3
LEFT
RIGHT
GBUF
VCC-1.8 VCC-1.8 VCC-1.8 VCC-1.8 VCC-3.3
E1 10uF
E2 10uF
CN2
PHONEJACK
LEFT
RIGHT
C16
10nF
C14
47nF
C15
10nF
R2710
R3020
R3120
R28 10
R29 10
R32
470 C173.3nF
R17100K
R33
470 C183.3nF
R18100K
L
R
R2227
2345671112
1314
25
24232221
18171615
8 1
19
9102726
20
28 29 30 31 32 33 34 35 36
373839404142434445464748M
CP/L
N1
MIC
NXR
ESET
DG
ND
0CV
DD
0IO
VDD
0CV
DD
1D
REQ
GPI
O2
GPI
O3
GPI
O6
GPI
O7
XDCS/BSYNCIOVDD1VC0DGND1XTAL0XTAL1IOVDD2DGND2DGND3DGND4XCSCVDD2
GPI
O5
RX
TX SCLK
SI SO CVD
D3
XTES
TG
PIO
0G
PIO
1G
ND
GPI
O4
AGND0AVDD0
AVDD2
AGND1AGND2
AGND3LN2
LEFT
RCAPAVDD1
GBUF
RIGHT
VS1053
U2
VCC-1.8 VCC-3.3
MP3-CS#
MP3
-RST
#
MP3-DCS
MO
SI2-
RG
8SC
K2-R
G6
MIS
O2-
RG
7
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
decoupling capacitors
Page 30 Page 31
9. USB-UART connection
Figure 9-1: Connecting USB
cable to programming connector
Mikromedia contains USB MINI-B connector
which is positioned next to the battery
connector. FT232RL USB-UART IC enables
you to implement UART serial communication
functionality via USB cable, since
dsPIC33FJ256GP710A does not support
USB protocol.
Before connecting the board, make sure that you have FTDI drivers installed on
your computer. Tx/Rx LED flashes when USB and controller communicate.
NOTE :
Page 30 Page 31
Figure 9-2: USB module connection schematics
VCC-3.3
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
SOSCOSOSCI
CLKOCLKI
MCU
-RX
MCU
-TX
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
3272
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A8182838485868788899091929394959697989910
0
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GNDVC
AP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
15161718192021222324252627281
23456789
1011121314
VCC-USB
C2810nF
FP2FERRITE
MCU-RX
R514K7
12345 GND
IDD+D-VBUS
CN3
USB MINIB
USBDPUSBDM
VCC-3.3
MCU-TX
VCC-3.3
R5210K
C34100nF
C36100nF
LD3TX/RX
R53220TXD
DTR#RTS#VCCIORXDRI#GNDNCDSR#DCD#CTS#CBUS4CBUS2CBUS3
CBUS0CBUS1
OSCOOSCITESTAGND
NC
GND
GND
VCCRESET#
3V3OUTUSBDMUSBDP
FT232RL
U4
FT232RL
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
Page 32 Page 33
C32100nF
C33100nF
VCC-3.3
R1210K
R1310K
VCC-3.3
1 2 3
J1
ACC ADDRESS123
VCCGNDRes4 GND5 GND6 VCC
7CS
8INT1
9INT2
10NC
11Res
12ADD
13SDA
14SC
L
U9
ADXL345
VCC-3.3
VCC-3.3 VCC-3.3
SCL1-RG2
SDA1-RG3
VCC-3.3
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
SDA1-RG3SCL1-RG2
SOSCOSOSCI
CLKOCLKI
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
10. Accelerometer
On board ADXL345 accelerometer is used to
measure acceleration in three axis: x, y and z. The
accelerometer’s function is defined by the user in the
program loaded into the microcontroller. Communication
between the accelerometer and the microcontroller is performed
via the I2C interface.
You can set the accelerometer
address to 0 or 1 by re-soldering the
SMD jumper (zero-ohm resistor) to the
appropriate position. Jumper is placed
in address 1 position by default.
Figure 10-2: Accelerometer connection schematics
Figure 10-1: Accelerometer
module
Page 32 Page 33
11. Flash Memory
VCC-3.3
R5 27
R4 27
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
MOSI2-RG8
SCK2-RG6
SOSCOSOSCI
CLKOCLKI
LCD
-RS
LCD
-YU
LCD
-XL
LCD
-YD
LCD
-XR
SD-C
D#
T-D
1
RD
14R
D15
MCU
-RX
MCU
-TX
RB9
RB8
PGD
1PG
C1
RF1
3R
F12
FLASH-CS#
MISO2-RG7
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
FLASH-CS#
C37
100nF
R4810K
VCC-3.3
VCC-3.3
VCC-3.3
123
54678
CSSDOWPGND SDI
SCKHOLD
VCC
U10
M25P80
MOSI2-RG8SCK2-RG6
MISO2-RG7
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
Figure 11-2:Flash memory module connection schematics
Since multimedia applications are
getting increasingly demanding, it is
necessary to provide additional memory
space to be used for storing more data.
The flash memory module enables the
microcontroller to use additional 8Mbit
flash memory. It is connected to the
microcontroller via the Serial Peripheral
Interface (SPI).
Figure 11-1:Flash memory module
Page 34 Page 35
R7 100
VCC-3.3
R5 27
R4 27
VREF-1.8
C31
22pF
C30
22pF
X3 32.768KHz
C2
22pF
C1
22pF
X1 8MHz
E9
10uF
MOSI2-RG8
SCK2-RG6
RD
1R
D2
RD
3
RD
4R
D5
RD
6
RF1
RF0
RG
0
MISO1-RF7SCK1-RF6
MOSI1-RF8
SDA1-RG3SCL1-RG2
SOSCOSOSCI
TX1-RF3RX1-RF2
RA14
RD0
RA15RD8RD9
CLKOCLKI
RD10
RD
14R
D15
RB9
RB8
PGD
1PG
C1
RF1
3R
F12
RG15
RA13RA12
RB1RB2RB3RB4RB5
MISO2-RG7
RC2
30292827 3433
58575655545352
463635 42 43 44 4537 50
9
48 49
1112
32
72
69686766656463
43
78 77
2423
181716151413
5678
10
7980
12
22212019
62616059
38 39 40 41 47
71
31
51
70
26
25
76
757473
dsPIC33FJ256GP710A
81828384858687888990919293949596979899100
RB1
1R
B10/
AN10
RB9
/AN
9R
B8/A
N8
RB1
3R
B12
RE7RC1RC2RC3
RA15
SCL1/RG2
RB1
5R
B14
SDO1/RF8SDI1/RF7SCK1/RF6SDA1/RG3
GN
DVC
C
RA6
RG
0R
G1
RE0 RF1
RF0
RD
7R
D6
RE6RE5
RE2
RG
13R
G12
RG
14R
E1
RA7
RG8/SDO2
RA9
/Vre
f-RB1RB2/AN2RB3RB4RB5RA13
RD9RD8
U1RX/RF2U1TX/RF3
GND
RG7/SDI2RG6/SCK2
RA1
RE3
RE4
RG15VCC
RB7
/PG
ED1
RB6
/PG
EC1
RB0
RF4
RF5
RA14
RA5
RD
14R
D15
RA2
RF1
3
VCC
RA3
VCC
VCC
RA12RA0VCC
GN
D
RF1
2
RA4
GND
VCAP
AGN
DAV
CCR
A10/
Vref
+
MCLR
RC4
CLKI/RC12CLKO/RC15
RD10
RD
3
RD
1
SOSCI/RC13SOSCO/RC14
GND
RD
2
RD
12R
D13
RD
4R
D5
RG9
RD11RD0
U1
RST
RXTX SCK
SDIADS ODS
SCL
AN
INT
PWM
VCC-3.3VCC-3.3
VCC-SYS
1234567891011121314151617181920212223242526
HDR1
M1X26
2728293031323334353637383940414243444546474849505152
HDR2
M1X26
RA13RA12
RA14
MOSI1-RF8
SCK1-RF6MISO1-RF7
RA15
RB1RB2RB3RB4RB5
RB9RB8
RG15
MOSI2-RG8
SCK2-RG6MISO2-RG7
RG0RD10
RB6RB7
RD14RD15
RF1RF0
SDA1-RG3SCL1-RG2
TX1-RF3RX1-RF2
LR
RD0RD1RD2RD3RD4RD5
RD6
RD8RD9
RF13RF12RC2
RST
C5
100nF
C6
100nF
C7
100nF
E8
10uF
VCC-3.3 VCC-3.3 VCC-3.3VCC-3.3
C8
100nF
VCC-3.3
decoupling capacitors
12. Pads
Most microcontroller pins are available for further connectivity via two 1x26 rows of connection
pads on both sides of the mikromedia board. They are designed to match additional shields,
such as Battery Boost shield, Gaming, PROTO shield and others.
Pads HDR2 Pads HDR1
Figure 12-1: Pads connecting schematics
Page 34 Page 35
13. Pinout
SPI LinesInterrupt LinesAnalog LinesPrograming lines I2C Lines UART lines PWM lines Comparator lines
5V RST Reset pin5V power supplyGND GND Reference GroundReference GroundRB1 LRB2 R
left ch.AN10right ch.AN2/SS1/CN4
RB3 RD0 OC1AN3/CN5RB4 RD1 OC2AN4/CN6RB5 RD2 OC3AN5/CN7RB8 RD3 OC4AN8RB9 RD4 OC5/CN13AN9
RA12 RD5 OC6/CN14AN20/INT1RA13 RD8 IC1AN21/INT2RA14 RD9 IC2INT3RA15 RD14 IC7/U1CTS/CN20INT4
RB6 RD15 IC8/U1RTS/CN21PGEC1/AN6/OCFARB7 RD6 OC7/CN15PGED1/AN7RF6 RC2 AN17/T3CK/T6CKSCK1/INT0RF7 RF12 U2CTSSDI1RF8 RF13 U2RTSSDO1
RG15 RF0 C1RXCOFSRG0 RF1 C1TXC2RX
RD10 RF2 U1RXIC3RG6 RF3 U1TXSCK2/CN8RG7 RG2 SCL1SDI2/CN9RG8 RG3 SDA1SDO2/CN103.3V 3.3V 3.3V power supply3.3V power supplyGND GND Reference GroundReference Ground
Pin functions Pin functions
audio out
CAN
UART
I2CSPI2
SPI1
Page 36 Page 37
73.66 mm
81.15 mm
63.5 mm
2.67 mm2.54 mm
36.5
8 m
m
55.8
8 m
m
60.4
5 m
m
2.03
mm
(3195 mils)
(2900 mils)
(238
0 m
ils)
(220
0 m
ils)
(2500 mils)
(144
0 m
ils)
(105 mils)(100 mils)
(80
mils
)
8.89
mm
(350
mils
)7.
62 m
m(3
00 m
ils)
14. Dimensions
Page 36 Page 37
15. mikromedia accessories
We have prepared a set of
extension boards pin-compatible
with your mikromedia, which
enable you to easily expand
your board basic functionality.
We call them mikromedia
shields. But we also offer other
accessories, such as Li-polymer
battery, stacking headers, wire
jumpers and more.
04
01
05 06 07
02 03
Gaming shield
Connect shield
Li-Polimer battery Wire Jumpers Stacking headers
BatteryBoost shield PROTO shield
Page 38 Page 39
You still don’t have an appropriate compiler? Locate dsPIC® compiler that suits you best on
the Product DVD provided with the package:
Choose between mikroC™, mikroBasic™ and mikroPascal™ and download fully functional
demo version, so you can begin building your first applications.
Once you have chosen your compiler, and since you already got the board, you are ready to start writing your first
projects. Visual TFT software for rapid development of graphical user interfaces enables you to quickly create your
GUI. It will automatically create necessary code which is compatible with mikroElektronika compilers. Visual TFT is
rich with examples, which are an excellent starting point for your future projects. Just load the example, read well
commented code, and see how it works on hardware. Visual TFT is also available on the Product DVD.
You have now completed the journey through each and every feature of mikromedia for dsPIC33 board. You got to know it’s modules and
organization. Now you are ready to start using your new board. We are suggesting several steps which are probably the best way to begin. We
invite you to join the users of mikromedia™ brand. You will find very useful projects and tutorials and can get help from a large ecosystem of
users. Welcome!
Compiler
Projects
DVD://download/eng/software/compilers/
What’s next?
Page 38 Page 39
DISCLAIMER
All the products owned by MikroElektronika are protected by copyright law and international copyright treaty. Therefore, this manual is to be treated as any other copyright material. No part of this manual, including product and software described herein, may be reproduced, stored in a retrieval system, translated or transmitted in any form or by any means, without the prior written permission of MikroElektronika. The manual PDF edition can be printed for private or local use, but not for distribution. Any modification of this manual is prohibited.
MikroElektronika provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties or conditions of merchantability or fitness for a particular purpose.
MikroElektronika shall assume no responsibility or liability for any errors, omissions and inaccuracies that may appear in this manual. In no event shall MikroElektronika, its directors, officers, employees or distributors be liable for any indirect, specific, incidental or consequential damages (including damages for loss of business profits and business information, business interruption or any other pecuniary loss) arising out of the use of this manual or product, even if MikroElektronika has been advised of the possibility of such damages. MikroElektronika reserves the right to change information contained in this manual at any time without prior notice, if necessary.
TRADEMARKS
The MikroElektronika name and logo, the MikroElektronika logo, mikroC™, mikroBasic™, mikroPascal™, mikroProg™, EasyPIC Fusion™, mikroBUS™, Click Boards™, mikroProg™, and mikromedia™ are trademarks of MikroElektronika. All other trademarks mentioned herein are property of their respective companies.All other product and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are only used for identification or explanation and to the owners’ benefit, with no intent to infringe.
Copyright © MikroElektronika, 2012, All Rights Reserved.
HIGH RISK ACTIVITIES
The products of MikroElektronika are not fault – tolerant nor designed, manufactured or intended for use or resale as on – line control equipment in hazard-ous environments requiring fail – safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines or weapons systems in which the failure of Software could lead directly to death, personal injury or severe physical or environmental damage (‘High Risk Activities’). MikroElektronika and its suppliers specifically disclaim any expressed or implied warranty of fitness for High Risk Activities.
If you want to learn more about our products, please visit our website at www.mikroe.com
If you are experiencing some problems with any of our products or just need additional
information, please place your ticket at www.mikroe.com/esupport
If you have any questions, comments or business proposals,
do not hesitate to contact us at [email protected] for dsPIC33® Manual
ver. 1.10b
0 100000 019672