MML Sports Ltd
18b Lanchester Way, Royal Oak, Daventry, Northamptonshire, NN11 8PH, UK
+44 1327 702975, [email protected]
MITSUBISHI LANCER EVO X GROUP N and R4 RALLY CAR
PRICE LIST JANUARY 2017
Prices are exclusive of VAT and shipping.All goods are subject to availability.Prices are correct at time of issue.All images are representative and actual product may vary.It is the responsibility of the consumer to determine suitability and legality of goods and services.Goods are sold for motorsport use only and no warranty is implied or given.MML Sports Ltd can not accept liability for products from third party suppliers.MML Sports Ltd reserves right to modify contents of the price list at any time.
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
CONTENTS 0 - 1 - 1
Group number
Sub-group number
Page number in sub-group
A - B - C
0 - 1 - CONTENTS
0 - 2 - GROUP N SPECIFICATION
0 - 3 - BASE CAR
1 - 1 - ENGINE MECHANICAL
1 - 2 - ENGINE LUBRICATION
1 - 3 - ENGINE FUEL SUPPLY
1 - 4 - ENGINE COOLING
1 - 5 - ENGINE INTAKE AND EXHAUST
1 - 6 - ENGINE ELECTRICAL
2 - 1 - CLUTCH
2 - 2 - TRANSMISSION
3 - 1 - WHEELS AND TYRES
3 - 2 - SUSPENSION
3 - 3 - BRAKES
3 - 4 - STEERING
4 - 1 - BODYSHELL
4 - 2 - GUARDS
5 - 1 - EXTERIOR
5 - 2 - INTERIOR
5 - 3 - CHASSIS ELECTRICAL
6 - 1 - R4 KIT
6 - 2 - R4 SUSPENSION
6 - 3 - R4 BODY AND INTERIOR
9 - 1 - INDEX
9 - 2 - NOTES
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
GROUP N RALLY CAR SPECIFICATION 0 - 2 - 1
Engine Carry out blue-print overhaul
Upgrade head gasket, studs and bolts
Upgrade connecting rods
Lubrication Upgrade oil and filter Change oil cooler hoses to aviation type
Fuel supply Modify injector rail Change fuel tank to safety cell
Change lines to aviation type Fit fuel sampling connector
Fit roll-over valve
Cooling Upgrade thermostat and radiator cap
Change radiator hoses to silicon VO option
Intake Change air suction pipe to VO option Carry out turbocharger blue-print overhaul
Fit air intake restrictor
Upgrade air filter
Exhaust Change pipe to straight layout system Change turbo outlet to fabricated part
Fit catalytic converter
Electrics Upgrade engine ECU w/map Upload fuel upgrade ECU map with
Upgrade spark plugs over-ride boost and launch control
Clutch Upgrade disc and cover Change master cylinder to VO option
Change feed pipe to aviation type
Gearbox Upgrade oil Change gear kit to dog engagement type
Upgrade centre differential transfer shaft
Differentials Upgrade front and rear LSD's to VO option Set-up LSD's to MML Sports settings
Change ACD hydraulic lines to aviation type Fit q/d coupling on ACD hydraulic lines
Upgrade ACD ECU w/map Upload performance ACD ECU map
Wheels Upgrade wheel studs and nuts
Use competition wheels
Suspension Change engine mounts to VO option Upgrade front and rear anti roll bars
Upgrade dampers and springs
Change suspension bushes to hard rubber
Brakes Upgrade master cylinder to VO option Fit front brake cooling ducts
Remove brake booster and fit VO adaptor
Fit VO hydraulic handbrake and bias valve
Fit front and rear VO brake kits
Upgrade brake pads to high-duty
Change lines to aviation type
Upgrade brake fluid
Steering Change steering wheel to competition type Upgrade steering wheel to lightweight carbon
Fit steering wheel hub adaptor and spacer Change PAS hoses to aviation type
Body De-seal, bead blast and de-bracket body
Fit roll cage, seat rails, axle stands
Fit brackets, bosses and studs for car build
Carry out paint work
Guards Fit protective guards for engine, transmission,
heat exchangers, underfloor, sills, fuel tank,
hydraulic pump, wheel arches, propeller
shaft, rear differential, rear suspension
Fit mud flaps
Exterior Fit bonnet and boot pins Fit roof vent and vertical door mirrors
Interior Fit footwells for driver and co-driver Fit interior door cards
Fit radio and floor console covers Fit screen and trip meter mounting brackets
Fit wheel brace and mechanical scissor jack Upgrade jack to monkey-on-stick type
Fit spare wheel strap Fit nut gun with mounting bracket
Fit competition seats and harnesses Upgrade seats to lightweight carbon
Fit hand held fire extinguisher Upgrade extinguisher to lightweight carbon
Fit glass anti-shatter film, roll cage padding, Flock dashboard top roll
first aid kit, harness cutters, warning triangle
Electrical Fit auxiliary loom kit with gel battery Fit dashboard screen, shift light, trip meter
Fit electrical fire extinguisher Upgrade light pod to HID unit
Fit halogen bonnet light pod
Labour Body, engine and transmission preparation, car build, engineering support
Other Consumables, shipping services, shakedown
BASE SPECIFICATION FULL SPECIFICATIONMinimum car build requirements Upgrades in addition to base specification
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
BASE CAR 0 - 3 - 1
MITSUBISHI LANCER EVOLUTION X RS
NEW CARS NO LONGER AVAILABLE GS41EVO
FIA HOMOLOGATION DOCUMENT #5718Original copy of Lancer Evolution X homologation
Includes A-5718 and N-5718 with all extensions
Free 'COPY'-watermarked version available from ralliart.com
FIA5718 £125
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE MECHANICAL 1 - 1 - 1
4B11 ENGINE ASSEMBLYGenuine MMC part
Complete engine assembly with all ancillaries including flywheel, clutch,
turbocharger, inlet/exhaust manifolds, pumps, electrical components
Series part for spares / replacement
1000B062
Gp N ENGINE BUILDEngine preparation by MML Sports to FIA Group N regulations
- Blueprint overhaul, inclusive of head gasket and bolt upgrade
- Con rod upgrade to VO homologated reinforced set
- Turbocharger overhaul, inclusive of Ø33 mm restrictor fitment
- Fuel rail and return modification for AN fittings
- Oil filter, thermostat, spark plug upgrade
Base engine to be supplied by customer or available direct from MML
99-GRNREBUILD (rebuild only)
99-GRNREBUILD-E (incl base engine)
REINFORCED CONNECTING ROD SETGenuine RalliArt part, VO homologated
Essential engine upgrade as part of Gp N preparation
High strength forged steel
Supplied as set of 4-off
RA111304S1
CYLINDER HEAD GASKETGenuine HKS part
Stopper type, multiple steel layers, fluorine rubber coating
87.5 mm bore, 1.0 & 1.2 mm thickness
23001-DM001
23001-DM002
CYLINDER HEAD STUD KITGenuine ARP part
ARP 2000 Pro Series, 35% increase in tensile strength over OE studs
Kit includes 10-off head studs, 10-off parallel ground washers,
10-off 8740-Cr-Mo steel nuts, and assembly lubricant
207-4206
£5,600
£6,600
£12,200
£154
£210
£210
£555
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE MECHANICAL 1 - 1 - 2
CYLINDER BLOCK MAIN STUD KITGenuine ARP part
ARP 2000 Pro Series, 50% increase in tensile strength over OE bolts
Kit includes 10-off M10 main studs, 10-off M8 main studs, 20-off
8740-Cr-Mo steel nuts, and assembly lubricant
207-5403
CONNECTING ROD BOLT SETGenuine ARP part
ARP 2000 Pro Series, 25% increase in tensile strength over OE bolts
Sold as set of 8 bolts
207-6002 £100
£173
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE LUBRICATION 1 - 2 - 1
ENGINE OIL FILTERGenuine MMC part
Series par for spares / replacement
MZ690150
ENGINE OIL COOLERGenuine MMC part
Series part for spares / replacement
1240A056
ENGINE OIL COOLER HOSE KITMML Sports specification, made to AN aerospace standard
Reliability upgrade, direct replacement for original hoses
Available as steel-braid nitrile hose or lightweight fibre-braid
teflon hose (200 grams lighter) GNX-12-01X (nitrile)
Supplied with installation diagram GNX-12-02X (teflon)
ENGINE OILGenuine Mobil1 product
5W50 performance synthetic engine oil
Suitable for all types of severe driving applications
6 litres required for engine fill 143642 (1 ltr)
143643 (4 ltr)
£255
£16
£45
£288
£20
£350
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE FUEL SUPPLY 1 - 3 - 1
SAFETY FUEL TANK KITGenuine ATL product
Aramid fibre safety cell conforming to FIA/FT3.5-1999 standard
80 litre capacity, to be mounted underfloor instead of original tank
Internal collector fitted with submerged fuel pump and sock filter
Top plate fitted with JIC06 feed, return and vent adaptors and
Staubli JIC12 refuelling plugs (fill and vent)
2-off integral float-type VDO fuel level sender units
Supplied with underfloor cover
Weight 6.86 kg (tank) + 2.88 kg (cover) EVO10/80-FT3.5
FUEL PUMP COVERFits over original fuel pump access hole in rear floor
Removable lid
Weight 300 g
EVO10/80FPCC
FUEL LINE KITMML Sports specification, made to AN aerospace standard
Includes feed & return hoses for engine bay (requires fuel injector rail
modification to take AN fittings), bulkhead fittings, feed & return hoses
through cockpit, fittings at fuel pump, high-pressure in-line filter, and
tank ventilation hoses with terminating breather filter
Allows fitment of q/d coupling for fuel sampling / draining (needs to
be purchased separately); requires fitment of FIA approved roll-over
valve (needs to be purchased separately)
Supplied with installation diagram GNX-13-02X
FUEL DRAIN KITMML Sports specification, made to AN aerospace standard
Includes q/d coupling (plug and socket) with PVC drain hose (2m in length)
Coupling is FIA approved for fuel sampling
Fits directly into fuel line kit GNX-13-02X
GNX-13-03X
FUEL ROLL-OVER VALVEGenuine ATL part
FIA approved valve for use on tank ventilation line
Compulsory as per FIA safety regulations
Fits directly into fuel line kit GNX-13-02X
FIAVV-SF
FUEL INJECTOR RAIL MODEssential modification for installation of aviation type fuel lines
JIC06 male fitting welded onto rail at feed end
JIC06 male adaptor for return at fuel pressure regulator
Original fuel rail to be supplied by customer
Exchange 99-GRNRETURN
Without Exchange 99-GRNRAIL £290
£220
£305
£203
£720
£350
£6,500
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE COOLING 1 - 4 - 1
THERMOSTATGenuine RalliArt part
Valve opening temperature 76 °C (standard value 76.5 ± 1.5 °C)
10% higher flow rate than OE thermostat
RA130548N1
RADIATORGenuine MMC part
Standard Evo 10 radiator for spares / replacement
VO homologated Outlander radiator (8 mm thicker and 5 mm taller)
available for increased cooling efficiency 1350A050 (Evo 10)
(at 1.1 kg weight penalty) 1350A206 (Outlander)
RADIATOR HOSE KITGenuine RalliArt part, VO homologated
Silicon hoses with steel jubilee clips
Reliability upgrade for heavy duty cooling requirements
Direct replacement for original hoses
Supplied as car-set RA137205S1
RADIATOR SUPPORT BUSHINGGenuine RalliArt part, strengthened rubber (HS80)
Lower support bushes for radiator
Original bushes to be used at top
Sold in bags of 2
RA605173K1
RADIATOR CAPGenuine RalliArt part
Valve opening pressure 127 kPa (standard value 93 - 123 kPa)
Direct replacement for original cap
RA431454N1 (black)
RA431454N2 (red)
ENGINE COOLANTGenuine Comma product
Premium traditional antifreeze, contains mono-ethylene-glycol
Protection range (ambient) from -36 °C to +45 °C
2.25 ltr required for system fill (at 30% conc) SCA1L (1 ltr)
Available in cans of 1 and 2 litres SCA2L (2 ltr) £8
£50
£280
£255
£28
£32
£5
£280
£28
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE INTAKE & EXHAUST 1 - 5 - 1
AIR SUCTION PIPE KITGenuine RalliArt part, VO homologated
Kit consists of cast aluminium intake pipe, 3-off silicone hoses with
steel jubilee clips, and 1-off rubber o-ring
To be used with Ø33 mm air intake restrictor
Direct replacement for original part RA150132N1
AIR FILTERGenuine ITG part representing ProFilter range
Unique Tri-Foam® system with three layers of foam gives high level of
filtration and exceptionally low pressure loss for increased engine power
Fitment requires aluminium frame WB-394 (with frame)
Direct replacement for original part WB-394-E (filter only)
INTERCOOLERGenuine MMC part
Series part for spares / replacement
1530A056
TURBOCHARGER ASSEMBLYGenuine MMC part
Series part for spares / replacement
1515A198
Gp N TURBOCHARGER BUILDTurbocharger preparation by HKS Europe to FIA Group N regulations
- Blueprint overhaul, inclusive of wheel balancing
- Fitment of Ø33 mm air intake restrictor with lockwire for sealing
Customer to supply base turbocharger
99-GRNTURBO
AIR INTAKE RESTRICTOR 33 mmConforms to 2010 FIA Group N regulations and N5718 homologation
Supplied with o-ring and drilled capheads
99-GRN33MM
TURBOCHARGER OIL DRAIN HOSEMML Sports specification
Flexible aviation type hose clamped onto original drain pipe fitting
Engine plug modified to take AN fitting
Original drain pipe to be supplied by customer
Included in Gp N Turbo Build package GNX-15-01X
£506
£95
£70
£195
£1,140
£255
£50
£785
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE INTAKE & EXHAUST 1 - 5 - 2
TURBOCHARGER EXHAUST OUTLET GPNFabricated part, direct replacement for OE casting
Offers weight saving and increases high-RPM power
Exact performance figures TBA
Supplied with OE gasket and stud
ME10EX#OTOINS
EXHAUST SYSTEM GPNSystem consists of Bolt Type Turbo Outlet incl heat sheild
Down Pipe with Heat Sheild, Pipe #2, Pipe#3, Pipe #4 & Pipe#5 Tailpipe
FIA approved catalytic converter is available for installation on tailpipe
and is compulsory in Group N
ME10EX#1D/PSINSA (Down Pipe with Heat Sheild)
ME10EX#2NOSIL (Pipe #2)
ME10EX#3 (Pipe #3)
ME10EX#4 (Pipe #4)
ME10EX#5 (Pipe #5 with CAT)
ME10EX#5NOSIL (Pipe #5 Plain)
FIT-GPN (Fitting Kit)
TURBOCHARGER EXHAUST OUTLET R4Fabricated part, direct replacement for OE casting
Offers weight saving and increases high-RPM power
Slip Joint System
Supplied with OE gasket and stud
ME10EX#1RAINSA
EXHAUST SYSTEM R4System consists of Slip Joint Turbo Outlet incl heat sheild
Pipe #2, Pipe#3 and Pipe #4 Tailpipe
FIA approved catalytic converter is available for installation on tailpipe
and is compulsory in Group N
EX1-R4 (Pipe #2)
EX2-R4 (Pipe #3)
EX5-R4 (Pipe #4 without CAT)
EX6-R4 (Pipe #4 with CAT)
FIT-R4 (Fitting Kit)
CATALYTIC CONVERTERGenuine HJS part
DMSB homologation WRC.1279-10
Proved on Mitsubishi World Rally Cars with zero failure record
90950044
£507
£171
£122
£140
£85
£58
£475
£50
£76
£507
£50
£90
£788
£788
£308
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
ENGINE ELECTRICAL 1 - 6 - 1
ENGINE ECU (STANDARD ECU SUPPLIED BY CUSTOMER)Genuine MoTeC product, plug & play device
M800 control unit with drive-by-wire, cam control and advanced functions
(anti-lag and launch control) enabled; supplied with base map; free
management software available from motec.com.au
Requires MoTeC ACD controller 13013
ENGINE ECU MAPEngine control map developed by MML Sports
Available for various fuels, PWRC control fuel and higher grades
Map is locked for viewing / editing
Available for MoTeC engine ECU only GNX-16-01 (PWRC)
GNX-16-02 (fuel upgrade)
SPARK PLUGGenuine HKS part
Super Fire Racing, XL type, heat 45 (NGK 9 equivalent)
High performance iridium plug designed for improved ignition
performance, durability and anti-carbon build-up
Supplied individually 50003-M45-XL
£1,995
£250
£450
£22
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
CLUTCH 2 - 1 - 1
CLUTCH DISCGenuine RalliArt part
Diameter Ø240 mm
RA567361K1
CLUTCH COVERGenuine RalliArt part
Diameter Ø240 mm
Press load 12.2 kN
RA980846K1
CLUTCH RELEASE BEARINGGenuine MMC part
2317A001
CLUTCH MASTER CYLINDERGenuine MMC part
VO homologated for use on Evo X with suitable adaptor kit
Cast aluminium part offers increased robustness over original plastic m/c
Requires adaptor kit and feed pipe kit MR491945 (LHD)
MR519378 (RHD)
CLUTCH MASTER CYLINDER ADAPTOR KITConforms to VO homologation spec
Allows upgrading clutch master cylinder to VO homologated option
Consists of machined and anodised adaptor plate and rod end
Supplied with mounting studs and rod end bolt with plastic bushing
RA340167N1C
CLUTCH FEED PIPE KITMML Sports spec, made to AN aerospace standard
Feed pipe from clutch master cylinder to slave cylinder at gearbox
For VO master cylinder option, banjo adaptor and bolt are supplied
If original master cylinder is retained, adaptor for AN fitting is supplied
OE m/c adaptor is also GNX-21-02X (LHD with VO m/c)
available individually GNX-21-03X (RHD with VO m/c)
Supplied with GNX-21-04X (LHD with OE m/c)
installation diagram GNX-21-05X (RHD with OE m/c)
GNX-21-06 (OE m/c adaptor only)
£95
£38
£68
£38
£62
£42
£285
£205
£76
£340
£205
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
TRANSMISSION 2 - 2 - 1
GEAR BOX ASSEMBLYGenuine MMC part
Series part for spares / replacement
2500A218
DOG ENGAGEMENT GEAR KITGenuine PPG product, fits into original casing
VO homologated gear ratios
The strengthened gear set includes upgraded billet selector forks
and final drive with two ratio options
SEQUENTIAL GEARKIT
GEARKIT
TRANSFER BOX ASSEMBLYGenuine MMC part
Series part for spares / replacement
3200A087
FRONT LSD KITGenuine RalliArt part, VO homologated
Mechanical type limited slip differential, fits into original transfer housing
40°/0° and 50°/0° ramp angles (accel/decel) available
Overhaul to MML Sports settings RA857885S1 (LSD)
available as additional service GNX-22-05J (overhaul)
FRONT LSD BEARING SETGenuine RalliArt part
Set consists of LH and RH bearings
Required for front LSD assembly as original bearings can not be re-used
Supplied as car-set
RA317750S1
FRONT LSD SPACER SETGenuine RalliArt part
Each set consists of 28-off spacers in 0.53 - 1.34 mm thickness range
Required for front LSD fitment into transfer box case
LH and RH are different diameters and RA315850S1 (LH)
are sold separately RA314750S1 (RH) £60
£105
£2,625
£5,950
£12,250
£6,815
£60
£320
£1,525
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
TRANSMISSION 2 - 2 - 2
FRONT LSD COVERReplacement RalliArt front LSD cover (A)
RA857885C1
FRONT LSD CROWN WHEEL BOLTGenuine RalliArt part
12-off required per car assembly
Sold individually
RACZ4206K1
TRANSFER BOX OVERHAUL KITGenuine RalliArt part
Kit consists of 2-off oil seals and 2-off o-rings
1-off kit required for front LSD fitment should original seals be damaged
RA315750S1
FRONT OUTPUT SHAFTGenuine MMC part
Series part for spares / replacement
3815A209 (LH)
3815A210 (RH)
FRONT DRIVE SHAFT ASSEMBLYGenuine MMC part
Series part for spares / replacement
3815A207 (LH)
3815A208 (RH)
REAR DRIVE SHAFT ASSEMBLYGenuine MMC part
Series part for spares / replacement
3715A133 (LH)
3715A134 (RH)
REAR DIFFERENTIAL ASSEMBLYGenuine MMC part
Series part for spares / replacement
3501A130
£688
£1,760
£688
£60
£395
£395
£380
£45
£60
£3
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
TRANSMISSION 2 - 2 - 3
REAR LSD KITGenuine RalliArt part, VO homologated
Mechanical type limited slip differential, fits into original housing
55°/35° and 55°/55° ramp angles (accel/decel) available
Overhaul to MML Sports settings RA166619K1
available as additional service GNX-22-06J (overhaul)
REAR LSD CROWN WHEEL BOLTGenuine MMC part
8-off required per car assembly
Sold individually
MB092220
REAR DIFFERENTIAL BEARINGGenuine MMC part
2-off required for rear LSD assembly
Supplied individually
MB393957
REAR DIFFERENTIAL SPACER SETGenuine MMC part
1-off set required for rear LSD assembly
Set consists of 6-off spacers
MR357058
ACD HYDRAULIC PUMPGenuine MMC part
Series part for spares / replacement
3520A046
ACD HYDRAULIC LINE KITMML Sports specification, made to AN aerospace standard
Kit consists of three hoses (rear bumper, cockpit, engine bay),
bulkhead fitting, and adaptors for hydraulic unit and clutch unit
Hoses are to length and steel fittings are crimped
Hoses are covered in abrasion and fire resistant sleeve
Dry-break coupling is available for installation between engine bay and
cockpit hoses for improved serviceability of vehicle
Supplied with installation diagram GNX-22-01X (without Q/D)
GNX-22-02X (with Q/D) £620
£330
£55
£320
£40
£940
£1,895
£2
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
TRANSMISSION 2 - 2 - 4
ACD HYDRAULIC CLUTCHGenuine MMC part
Series part for spares / replacement
RA310050S1
GEARBOX OILGenuine Castrol product
SAE 75W140 fully synthetic gear oil
2.5 ltr required for gearbox fill
Supplied in 1 ltr cans
(1 ltr)
DIFFERENTIAL OILMMC approved product
SAE 80W90 GL5 mineral gear oil
0.8 ltr required for transfer box fill, 0.6 ltr for rear differential
Supplied in 1 ltr cans
L-996 (1 ltr)
ACD HYDRAULIC FLUIDGenuine Castrol product
Dexron® III automatic transmission fluid
Specified by manufacturer as suitable for hydraulic units
0.9 ltr required for system fill
Supplied in 1 ltr cans (1 ltr)
ACD ECUGenuine GEMS product
Bolt-in replacement for original control unit; supplied with base map;
five selectable control modes (no lock, full lock, and three user-configurable);
free management software available from gems.co.uk
99-ACDEVOX
ACD ECUGenuine MoTeC product, plug & play device
Bolt-in replacement for original control unit; supplied with base map;
six selectable control modes (no lock, full lock, and four user-configurable);
free management software available from motec.com.au
Supplied with CAN comms cable 14016
ACD ECU MAPActive centre differential control map developed by MML Sports
3-mode map to suit different driving styles and conditions on gravel
or tarmac roads; combination of the two is available upon request
Available for both GEMS and GNX-22-03 (gravel)
MoTec control units GNX-22-04 (tarmac)
£898
£200
£200
£12
£18
£12
£1,185
£650
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
WHEELS 3 - 1 - 1
ALUMINIUM COMPETITION WHEELSGenuine SL Corse product, cast aluminium alloy
Type 2118 7×15 ET28 for gravel
Type 2120 8×18 ET12 for tarmac
Please enquire about other sizes 2118 (gravel)
2120 (tarmac)
MAGNESIUM COMPETITION WHEELSGenuine SL Corse product, cast magnesium alloy
Type 2020 7×15 for gravel, weight 8.6 kg (min Group N)
Type 2021 8×18 for tarmac, weight 8.9 kg (min Group N)
Please enquire about other sizes 2020 (gravel)
2021 (tarmac)
WHEEL STUDSAvailable as individual studs or complete car-set (20-off)
M12×1.5, 63 mm long
Sold individually
SS39
WHEEL NUTSAvailable as individual nuts or complete car-set (20-off)
M12×1.5, open ended
19 mm hex
Sold individually
BIM/D110/12X1.5N £2.20
£2.20
£110
£195
£345
£495
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
SUSPENSION 3 - 2 - 1
ENGINE MOUNTGenuine RalliArt part, VO homologated
Lightweight design, direct replacement for original part
RA033292S1
GEARBOX MOUNTGenuine RalliArt part, VO homologated
Lightweight design, direct replacement for original part
RA033722S1
BOS DAMPER ASSEMBLY CR60 (gravel FR)
Shock absorber and spring assembly CR60 (gravel RR)
3-way adjustable monotube hydraulic CR50 (tarmac FR)
dampers, single piston, CAS system and CR50 (tarmac RR)
hydraulic bump stop (gravel only) Gravel car-set
Priced individually or per car-set Tarmac car-set
EXE-TC DAMPER ASSEMBLY NM08-1002 (gravel FR)
Shock absorber and spring assembly NM08-1003 (gravel RR)
4-way adjustable, double piston NM08-1004 (tarmac FR)
damping system NM08-1005 (tarmac RR)
Supplied with rear top mounts and Gravel car-set
set-up kit; priced individually or per car-set Tarmac car-set
REIGER DAMPER ASSEMBLYShock absorber and spring assembly
Double piston, rebound control (optional on tarmac),
front corner control valve (tarmac only) Gravel car-set
Supplied with rear top mounts, camber Tarmac car-set
shims and C-spanners Tarmac car-set (w/rebound)
FRONT TOP MOUNT PLATE KITGenuine RalliArt parts, VO homologated
Set consists of LHS and RHS top mount plates
Spherical bearing (ID 22.0 mm)
Compatible with all Gp N dampers in use RA406134S1 (LH)
RA406134S2 (RH)
REAR TOP MOUNT PLATE KITUniversal part to fit to Evo X rear spring housing
Spherical bearing (ID 20.0 mm)
2-off required for car build
RM08-965 (1-off) £125
£6,970
£1,395
£2,090
£2,090
£6,970
£2,400
£9,680
£1,780
£1,395
£695
£7,320
£3,060
£784
£1,260
£10,515
£340
£340
£9,145
£8,945
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
SUSPENSION 3 - 2 - 2
REAR TOP MOUNT BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Set consists of pair of upper and pair of lower bushes
To be used with original rear top mounts
Bushes sold in bags of 2 pieces RA554369K1 (upper)
RA554370K1 (lower)
FRONT LOWER ARM BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Set consists of pair of front and pair of rear bushes
Bushes sold in bags of 2 pieces
RA554817K1 (front)
RA401121K1 (rear)
REAR UPPER AND TRAILING ARM BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Set consists of pair of upper arm
front, pair of upper arm rear and RA554817K1 (upper front)
pair of trailing arm front bushes RA411056K1 (upper rear)
Bushes sold in bags of 2 pieces RA411056K1 (trailing front)
ENGINE ROLL STOP BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Set consists of front and rear bushes
Bushes sold in bags of 1 piece
RA184354K1 (front)
RA554855K1 (rear)
REAR DIFFERENTIAL MOUNT BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Set consists of pair of front and single rear bush
Front bush sold in bags of 2 pieces
Rear bush sold in bags of 1 piece RA369384K1 (front)
RA351725K1 (rear)
FRONT ANTI ROLL BARGenuine RalliArt part, VO homologated
Direct replacement for original ARB (Ø25 mm)
Available in Ø 23mm (gravel) and Ø27 mm (tarmac) sizes
RA45612N23 (Ø23 mm)
RA45612N27 (Ø27 mm)
REAR ANTI ROLL BARGenuine RalliArt part, VO homologated
Direct replacement for original ARB (Ø23 mm)
Available in Ø25 mm (gravel) and Ø27 mm (tarmac) sizes
RA41562N25 (Ø25 mm)
RA41562N27 (Ø27 mm)
£775
£885
£36
£38
£485
£210
£30
£202
£64
£210
£42
£64
£405
£26
£26
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
SUSPENSION 3 - 2 - 3
FRONT ANTI ROLL BAR BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Pair of bushes to fit standard size anti roll bar (Ø 25 mm)
Can be used in rear for Ø 25 mm ARB or
modified for use on front/rear Ø 27 mm ARB
Bushes sold in bags of 2 pieces RA554095K1
REAR ANTI ROLL BAR BUSHINGGenuine RalliArt parts, strengthened rubber (HS80)
Pair of bushes to fit standard size anti roll bar (Ø 23 mm)
Bushes sold in bags of 2 pieces
RA415633K1
£68
£66
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
BRAKES 3 - 3 - 1
BRAKE MASTER CYLINDERGenuine MMC part, VO homologated
Direct replacement for original master cylinder
Supplied with fluid reservoir
4625A093
BRAKE BOOSTER ADAPTORGenuine RalliArt part, VO homologated
To be fitted when original brake servo is removed
Kit consists of adaptor and push-rod
RA033289S1
BRAKE PROPORTIONING VALVEGenuine AP Racing part, VO homologated
Mechanical brake pressure bias control valve
Lever type with 7 positions
CP4550-1
HAND BRAKE LEVER KITGenuine RalliArt part, VO homologated
Kit consists of lever and rod-end
To be mounted on platform
RA626779N1
HAND BRAKE MASTER CYLINDERGenuine Brembo part, VO homologated
Tandem master cylinder to be used with hand brake lever kit
Available in Ø16 mm, Ø17 mm, X.A7.B9.11 (Ø16 mm)
and Ø18 mm sizes X.A7.B9.12 (Ø17 mm)
X.A7.B9.13 (Ø18 mm)
HAND BRAKE MOUNTING PLATFORMMML Sports spec
Fits onto floor tunnel and takes hand brake lever kit
GNX-35-02 (LHD)
GNX-35-03 (RHD)
FRONT BRAKE KITGenuine Brembo part, VO homologated
Kit consists of 4-piston caliper, caliper mounting bracket with bolts,
Ø 300 mm (gravel) or Ø 355 mm (tarmac) disc and bell assy
Supplied as axle-set XA7.G0.YY (gravel)
XA7.G0.XX (tarmac) £4,735
£535
£535
£4,545
£310
£535
£50
£50
£955
£265
£360
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
BRAKES 3 - 3 - 2
REAR BRAKE KITGenuine Brembo part, VO homologated
Kit consists of 4-piston caliper, Ø 295 disc and bell assy, bolt set
For use on gravel or tarmac spec cars
Supplied as axle-set
XA7.G0.ZZ
BRAKE CALIPERGenuine Brembo part
Replacement part for VO brake kit XA5.T0.03 (LHF)
Supplied individually XA5.T0.04 (RHF)
XA7.G0.11 (LHR)
XA7.G0.12 (RHR)
BRAKE DISC & BELL ASSY XA7.G0.21 (gravel LHF)
Genuine Brembo part XA7.G0.22 (gravel RHF)
Replacement part for VO brake kit XA7.G0.31 (tarmac LHF)
Supplied individually XA7.G0.32 (tarmac RHF)
XA7.G0.23 (gravel/tarmac LHR)
XA7.G0.24 (gravel/tarmac RHR)
BRAKE DISC 098.647.13 (gravel LHF)
Genuine Brembo part 098.647.23 (gravel RHF)
Replacement part for VO brake kit 099.306.31 (tarmac LHF)
Supplied individually 099.306.41 (tarmac RHF)
097.277.09 (gravel/tarmac LHR)
097.277.19 (gravel/tarmac RHR)
REAR BRAKE DISC COVER SETGenuine RalliArt part, VO homologated
To be used with VO homologated Brembo rear brakes
Supplied individually, 2-off needed for axle-set
RA480059N1
FRONT BRAKE COOLING DUCT KITGenuine RalliArt part, VO homologated
Kit consists of 2-off composite air ducts to be fitted to front bumper
and flexible Ø95 mm ducting to guide airflow into wheel arches
Supplied with installation instructions
RACZ4602S1
£130
£560
£595
£355
£255
£255
£255
£580
£685
£595
£355
£255
£685
£580
£1,795
£1,055
£3,200
£1,055
£1,795
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
BRAKES 3 - 3 - 3
BRAKE LINE KITMML Sports specification, made to AN aerospace standard
Kit consists of engine bay hoses, cockpit hoses, wheel arch hoses,
bulkhead fittings, adaptors for valves / cylinders / calipers
Hoses are covered in abrasion and fire resistant sleeve
Hose fittings crimped to length
Supplied with installation diagram
GNX-35-04X (LHD)
GNX-35-05X (RHD)
WHEEL ARCH BRAKE LINE KITMML Sports specification, made to AN aerospace standard
Kit consists of 4-off wheel arch hoses and 4-off banjo bolts for calipers
Hoses are covered in abrasion and fire resistant sleeve
Steel fittings crimped to length
Included under the full brake line kit GNX-35-06X
BRAKE PADSGenuine Performance Friction product, 07 compound
Designed for high grip and severe duty applications, good
initial bite and average torque 7770.07.18.44 (gravel FR)
Very low abraded disc wear 7772.07.18.44 (tarmac FR)
Supplied as axle-set 7735.07.20.44 (gravel/tarmac RR)
BRAKE PADSGenuine Carbone Lorraine product
RC8 compound in front offers very high and stable friction level
RC6 in rear allows brake bias 5036W50T17-RC8 (gravel FR)
Very good initial bite 5011W61T17-RC8 (tarmac FR)
Supplied as axle-set 5006W43T20-RC6 (gravel/tarmac RR)
BRAKE PADSGenuine Endless product, N35S compound
Offers good compromise between initial bite and brake power
Well balanced in both wet and dry RCP108N35S (gravel FR)
Exceptionally low disc wear RCP109N35S (tarmac FR)
Supplied as axle-set RCP001N35S (gravel/tarmac RR)
BRAKE FLUIDGenuine Brembo product, LCF600 fluid
Exceeds DOT4 specification
Offers low compressibility at high temperatures
Supplied as 0.5 litre can
2-off cans required for system fill and bleed 04.8164.11
£317
£95
£185
£145
£220
£392
£354
£21
£995
£995
£235
£245
£165
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
STEERING 3 - 4 - 1
PAS HOSE KITMML Sports specification, made to AN aerospace standard
Kit consists of HP feed and LP return hoses, adaptors for pump and rack
RHD kit available with titanium Q/D GNX-37-01X (LHD)
coupling on HP hose for serviceability GNX-37-02X (RHD)
Supplied with installation diagram GNX-37-03X (RHD Q/D)
STEERING WHEELGenuine SPARCO part
3 spokes, 6-off bolts and horn button included, available in black
metal finish or carbon, suede cover, diameter Ø330 mm, depth
39 mm (metal) or 30 mm (carbon) 015R383PSN (metal)
015RC385SN (carbon)
STEERING WHEEL HUB ADAPTORGenuine OMP part
Takes all traditional 6-bolt steering wheels and spacers
Allows wiring of horn button in centre of steering wheel
Includes 6-off bolts, horn button extension leads
and dummy resistor to replace air bag OD/1960/MI280A
STEERING WHEEL HUB SPACERGenuine SPARCO part
50 mm spacer, suits all traditional 6-bolt 01595BLK (black)
steering wheels and hub adaptors 01595B (blue)
Available in black, blue, red, or silver 01595R (red)
Anodised finish 01595N (silver)
STEERING RACK ASSEMBLYGenuine MMC part
Series part for spares / replacement
4410A192 (LHD)
(RHD)
PAS OIL PUMP ASSEMBLYGenuine MMC part
Series part for spares / replacement
4450A097
PAS FLUIDGenuine Castrol product
ATF Dexron III
Approximately 1 litre required for system fill
Supplied as 1 litre can
CastrATFDexIII
£150
£555
£65
£14
£764
£65
£764
£65
£65
£530
£65
£80
£60
£645
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
BODYSHELL 4 - 1 - 1
ROLL CAGEGenuine KBT product, certified by SBF (Swedish ASN)
Supplied as weld-in kit
Supplied with original ASN certificate
RC-EVO10
BIW BEAD BLASTProcess allows removal of original paint and coating to expose
bare bodyshell for enhanced shell preparation
Separate panel blasting is also required if
colour code is changed from base car BBL-SHL (shell)
BBL-PNL (panels)
Gp N BODY PREPARATIONBodyshell preparation to FIA Group N regulations; requires body to be
de-sealed and bead blasted (not included); includes de-bracketing to VO
homologation, fitment of roll cage (cage not included), seat rails and harness
bosses, various bosses and studs for car build, various mounting brackets
and blanking discs, and axle stands GNX-42-01J
PAINT WORKCapability ranges from singe colour to complex colour scheme
Separate panel paint work is required if colour
code is changed from base car PNT-MONO (single colour)
PNT-MULTI (colour scheme)
PNT-PNL (panels)
WINDSCREENGenuine MMC part
Series part for spares / replacement
6102A494 (LHD)
6102A486 (RHD)
REAR GLASSGenuine MMC part
Series part for spares / replacement
6131A089
£720
£155
£1,800
£2,400
£900
£1,780
£155
£6,200
£240
£205
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
GUARDS 4 - 2 - 1
ALI SUMP GUARD 6mm or 8mmSuitable for rough gravel rallies or Safari
Supplied with top hat bushes for crossmember & front mounting
Note: Front Splitter Sold Seperately
GNX-44-50X
COMPOSITE SUMP GUARD SPLITTERKevlar construction
Fits directly to front ali guard
GNX-44-70
COMPOSITE SUMP GUARDCarbon and/or Kevlar construction
Fits directly to front chassis crossmember (radiator mount panel)
and front suspension crossmember
Available in tarmac and gravel spec
GNX-44-81
SUMP GUARD MOUNTING KIT 2 x Mounting plates with top hat tubes
2 x Replaceable threaded mounting bushes
2 x Top hat bushes for front cross member
GNX-44-90 - ALI GUARD
GNX-44-91 - COMP GUARD
UNDERFLOOR GUARDSTwintex underfloor protection
Material thickness 3 - 4 mm
Total weight (of pair) 14.0 kg
0810121T (LH)
0810122T (RH)
FRONT SILL GUARDSAramid fibre sill protection, front part
Material thickness 3 - 4 mm
Outer layer painted black
0810137A (LH)
0810138A (RH)
REAR SILL GUARDSAramid fibre sill protection, rear part
Material thickness 2 - 4 mm
Outer layer painted black
0810139A (LH)
0810140A (RH)
£237
£480
£160
£377
£655
£275
£377
£160
£237
£275
£1,286
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
GUARDS 4 - 2 - 2
FUEL TANK GUARDSTwintex protection for ATL safety fuel cell
Material thickness 3 - 4 mm
Total weight (of pair) 3.1 kg
0810177T (LH)
0810178T (RH)
HYDRAULIC PUMP GUARDTwintex protection for ACD hydraulic unit
Material thickness 2 mm
Weight 0.3 kg
0810174T
FRONT WHEEL ARCH LINERSProtection for front wheel arches
Material thickness 1.2 mm
Openings for front brake cooling
0810184T (LH)
0810185T (RH)
REAR WHEEL ARCH LINERSProtection for rear wheel arches
Material thickness 1.2 mm
0810186T (LH)
0810187T (RH)
REAR BUMPER GUARDSTwintex protection for rear wheel arches and bumper
Material thickness 2 mm
Total weight (of pair) 1.0 kg
0810175T (LH)
0810176T (RH)
REAR SUSPENSION GUARDSThermoplastic protection for rear suspension links
Material thickness 5 mm
Quick release fastener around rear lower arm
GNX-44-10X (LH)
GNX-44-11X (RH)
MUD FLAPSGenuine Kay-Dee product
Moulded flaps resistant to both high impact and abrasion
Available in wide range of colours
Supplied as car-set
KAY-E10
£154
£154
£220
£145
£145
£168
£168
£105
£105
£187
£140
£140
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
GUARDS 4 - 2 - 3
PROPELLER SHAFT GUARDAvailable in two versions,
(a) aluminium RalliArt guard (2.1 kg)
(b) twintex construction (1.1 kg)
Supplied with fitting kit RACZ4408R1 (aluminium)
RACZ4408R1CARA (twintex)
REAR DIFFERENTIAL GUARDAvailable in two versions,
(a) aluminium RalliArt guard (1.3 kg)
(b) twintex construction (0.7 kg)
Supplied with fitting kit RACT9404R1 (aluminium)
RACT9404R1CARA (twintex)
£135
£235
£185
£245
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
EXTERIOR 5 - 1 - 1
ROOF VENTVO homologated
Made of carbon fibre
Kit consists of exterior and interior parts,
2-off sock filters and drain tube
GNX-51-01X
DOOR MIRRORSMade of carbon fibre, improves aesthetics and
reduces excrescence drag increment 0810172C (mirror LH)
Supplied with mirror glass glued in 0810173C (mirror RH)
place (replacement glass also 0810135A (glass LH)
available separately) 0810136A (glass RH)
REAR WINDOW VENTSMade of carbon fibre with high quality foam filter on inside
Affixes against window edge with strong carbon channel
Sold individually, 2'off required per car
0810165C
BONNET PINSTraditional solution for bonnet and boot latching
Available in steel or silver-anodised aluminium
2-off sets needed for car build
C01 (steel kit, set of 2)
C01S (aluminium kit, set of 2)
NUMBER PLATESFull-size number plate sticker for rear
Small-size number plate sticker for front GNX-51-02 (rear)
Full-size laminated number plate GNX-51-03 (front small)
on Foamex board for front GNX-51-04 (front standard)
Available individually or as car-set Complete car-set
£8
£23
£40
£20
£15
£15
£896
£209
£209
£88
£6
£6
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
INTERIOR 5 - 2 - 1
DRIVER'S FOOTWELLMade of carbon fibre, weighs only 680 grams
0810170C (LHD)
0810189C (RHD)
CO-DRIVER'S FOOTWELLMade of carbon fibre, weighs only 960 grams
Provides mounting for hand-held fire extinguisher
bottle (supplied with metal straps)
0810171C (LHD)
0810190C (RHD)
FLOOR CONSOLE COVERMade of carbon fibre, weighs only 340 grams
Slides over gear lever and provides aesthetical finish for floor console
which is free to remove under Group N regulations; recessed aperture
takes switch panel of MML Sports auxiliary loom (see page 5-3-1)
0810188C
RADIO BLANKING PANELMade of carbon fibre, weighs only 45 grams
Provides aesthetical finish for instrument panel when original
trim and instruments are removed
0810159C
DASHBOARD SCREEN MOUNTING PANELMade of carbon fibre, weighs only 60 grams
Designed to provide mounting for MoTeC SDL dashboard screen
Fits into original radio / sat nav aperture of instrument panel
0810183C
TRIP METER MOUNTING BRACKETMade of carbon fibre, weighs only 120 grams
Designed to provide mounting for Coralba C-Giant trip meter
Fits onto instrument panel over original passenger's air bag cover
Currently available for LHD only
0810182C (LHD)
NUT GUN MOUNTING BRACKETMade of carbon fibre
Designed for Makita impact wrench
Can be mounted on flat surface or onto rollcage
Supplied with quick release strap
9900111C
£357
£68
£185
£412
£412
£209
£140
£368
£368
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
INTERIOR 5 - 2 - 2
FRONT DOOR CARDSMade of carbon-fibre
Average material thickness 1.5 mm
Total weight (of pair) 2.1 kg
Takes OE door handle and window switches 0810144C (LH)
0810145C (RH)
REAR DOOR CARDSMade of carbon-fibre
Average material thickness 1.5 mm
Total weight (of pair) 1.7 kg
Takes OE door handle 0810146C (LH)
0810147C (RH)
MIRROR MOUNT COVERSMade of carbon-fibre
Provides aesthetical interior finish
0810148C (LH)
0810149C (RH)
DASHBOARD FLOCKINGTop roll of instrument panel flocked in black to eliminate light reflection
Customer to supply IP
Other colours available on request
GNX-52-01J
BATTERY OPERATED IMPACT WRENCH KITGenuine Hitachi product
14.4V cordless impact wrench to be used as wheel nut gun
Supplied with genuine 2-off Li-ion batteries and charger
Anodised Cr-Mo socket supplied separately WR14DL
SX03019 (19 mm socket)
WHEEL BRACELightweight wheel brace with spin handle and 19 mm socket
TIG welded, black powder coated
Supplied with mounting bracket
WB19MM
HYDRAULIC SCISSOR JACKGenuine KYB product
Total weight (jack and handle) 5.5 kg
Lifting height 117 - 380 mm
Capacity 800 kg
KJZ008
£140
£27
£210
£290
£15
£55
£439
£439
£27
£420
£420
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
INTERIOR 5 - 2 - 3
MECHANICAL MONKEY ON STICK JACKAdopted from OEM product, lightweight design
Supplied with pin to required diameter and foot bar to required height
Good cost compromise when low minimum lifting height is required
GNX-52-02X
HYDRAULIC MONKEY ON STICK JACKExceptionally strong design, offers very quick lifting action and almost
instantaneous release, alloy foot plate with roll feature, supplied
with pin 23mm dia
Can lift vehicle from virtually zero height
Total weight (jack and handle) 3.8 kg AIT-LIFT09
SPARE WHEEL STRAPGenuine TRS product
3-point attachment to body, adjustable strap length
Fitted with ratchet and flat hook
MA620-0001
FIBREGLASS COMPETITION SEATGenuine Sparco product 00824F (Corsa)
Fibreglass shell 00807F (Evo)
High / wide options available 00808F (Pro 2000)
NR black, AZ blue, RS red 00806F (Circuit)
Priced per seat 00809F (Pro-ADV)
CARBON COMPETITION SEATGenuine Sparco product 00807Z (Evo)
Carbon fibre shell 00808Z (Pro 2000)
Up to 3 kg weight saving per seat 00806Z (Circuit)
NR black, AZ blue, RS red 00810Z (S-Light)
Priced per seat 00809Z (Pro-ADV)
COMPETITION SEAT MOUNTSGenuine Sparco product, FIA approved
Lightweight design, alloy construction
Fits Sparco, OMP, Cobra and Corbeau seats
Supplied as pair
00499AL
COMPETITION SEAT MOUNTSGenuine Sparco product, FIA approved
Lightweight design, alloy construction
Universal fit
Supplied as pair
00489PRO
£75
£170
£1,395
£1,200
£341
£1,200
£341
£22
£350
£730
£411
£411
£1,395
£1,300
£165
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
INTERIOR 5 - 2 - 4
COMPETITION HARNESSESGenuine Sparco product, FIA approved, 6-point attachment to body,
quick release buckle, lightweight adjusters, available as 2" straps all
over (base) or with 1" straps (single or 04827BM (base)
double) for HANS device 04817RH (HANS single belt)
NR black, AZ blue, RS red 04827TW (HANS double belt)
ROLL CAGE PADDINGGenuine Sparco product, FIA approved
Mandatory where crash helmets can come into contact with roll cage
Sold in sets of 2 pcs, each 500 mm long 0076040 (Ø40 mm)
0076045 (Ø45 mm)
0076050 (Ø50 mm)
HAND HELD FIRE EXTINGUISHERGenuine Spa Design product
2.4 litre bottle available in metal or carbon fibre
Supplied with 2-off metal straps and 1-off mounting bracket
HH240 (metal)
HH240CF (carbon)
FIRST AID KIT15 item basic kit
Includes antiseptic cleansing tissues and cream, scissors, woven bandage,
safety pins, various dressings and first aid primary care guide
Weighs 180 grams
Supplied in pouch 1040
EMERGENCY HARNESS CUTTERSignal-red, fixed-blade emergency seat belt cutter
Supplied with Velcro fastener for convenient attachment
2-off mandatory per car under FIA safety regulations
Price per 1-off
537
EMERGENCY WARNING TRIANGLETo European Standard ECE R27
Manufactured from ABS plastic, folding design with stand and
rubber feet; supplied in plastic carrying case
Price per 1-off
WT1
GLASS ANTI-SHATTER FILMGenuine Foliatec product
High strength protective window film offering glass splinter protection
Mandatory on side windows under FIA safety regulations
Supplied as 51×400 cm sheet (enough for one car build)
1164
£14
£10
£65
£650
£75
£35
£175
£260
£175
£35
£35
£18
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
CHASSIS ELECTRICAL 5 - 3 - 1
AUXILIARY LOOM KITMML Sports specification, fully legal in Group N, plug&play type
- battery cables with isolator (battery not included)
- ignition key interface for switch-operated function
- CAN bus link from ACD controller (to fit MoTeC MDC2)
- floor console switch panel with power / ignition / start switches, six
circuit breakers, and fire extinguisher power pack (fits into carbon floor
console cover 0810188C which needs to be purchased separately)
- external kill / fire switches for mounting on scuttle panel
- ACD and ALS mode toggle switches for mounting on floor console
- connector for electrical fire extinguisher (to fit Lifeline fire bottle)
- fuel pump and fuel level interface (to fit ATL safety fuel cell)
- connector for shift light (to fit MoTeC SLM)
- connector for dashboard screen (to fit MoTeC SDL3) with auxiliary
socket and two external switches for mounting on floor console
- USB socket for PC communication to MoTeC engine ECU and ACD
controller via CAN link (MoTeC UTC converter not included)
- Ethernet socket for PC communication to MoTeC SDL3 screen
- radio interface loom for wheel speed input
- trip meter interface loom (to fit Coralba C-Giant)
- connector for map light (map light not included)
- two foot switches and wiring to co-driver's footrest for trip meter
reset and windscreen wash/wipe
- wiring to hydraulic handbrake switch for ACD controller input
- bulkhead connectors for auxiliary light looms (bonnet pod, corner pods
and their extension looms need to be purchased separately)
- two auxiliary connectors at floor console
All auxiliary devices are optional, their absence does not affect functionality
of the loom; loom is designed to work with the particular devices as specified
above, please enquire if intending to use different spec; LHD/RHD versions
available; ACD controller comms cable, fire extinguisher power pack and OE
intercooler water spray switch to be supplied by customer
Supplied with installation instructions 5395
5395R4
GEL BATTERYGenuine Red Top 40 from Varley
Voltage 12 V, capacity 35 Ah, weight 14.6 kg, dimensions 250×97×202 mm
Exceptionally high cranking power, high shock and vibration resistance,
maintenance free, sealed construction, no electrolyte leakage
Reliability proved in WRC, WTCC, NASCAR, etc 7065-0007
ELECTRICAL FIRE EXTINGUISHER KITGenuine 3 kg Zero 360 remote charge piston system from Lifeline
FIA homologated, light and compact, two year service life
Kit includes cylinder with bracket and straps, remote cartridge with link
hose, power pack, waterproof activation switches with aluminium bezels,
standard plug and lead assembly, semi-rigid tube with heat protective
overbraid, connectors and fittings, nozzles, and decal pack
Supplied as complete kit
104-225-003
£4,250
£1,100
£205
£3,950
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
CHASSIS ELECTRICAL 5 - 3 - 2
DASHBOARD SCREENGenuine MoTeC product, all-in-one display, logger and controller
Customisable screen layout, measurement units and warnings
User-defined alarms, programmable overrides 18017 (base)
Options include backlight and logging 18018 (backlit)
Free management software 29414 (16MB logging)
SHIFT LIGHT MODULEGenuine MoTeC product
Array of eight full colour (RGB) LED's, can be used as shift lights,
warning lights or other indicators as programmed by user
Configured and controlled from MoTeC ECU, display or data logger
Communicates over CAN link 18120
TRIP METERGenuine Coralba product
C-Giant incorporates three independent very precise distance meters,
two time registers, speed display function, and automatic SS measurement
Supplied with CAN converter for wheel speed input from radio signal
Requires 12 V power, weighs 370 grams C900
MAP LIGHTGenuine Grayston product
Flexible body, 457 mm (18 in) length, cone shaped hood over light,
integral push on/off switch; other spec available on request
Supplied with unterminated wires and screws for installation
GE46
INTERCOMGenuine Stilo product, the ultimate intercom system
Two separate circuits (high volume / noise cancelling) with radio,
mobile phone and camera connection ST-30
Power/camera/mic and helmet wiring Power loom
looms available separately Helmet loom
BONNET LIGHT PODGenuine PIAA product, 2-off drive lamps and 2-off spot lamps
Supplied with PIAA 80 Series Competition lamps and mounting rings
Halogen and HID options available PLP1010WL (halogen)
Halogen bulbs and extension PLP1010HID (HID lamps)
loom to be purchased separately 5395-06 (extension loom)
HALOGEN LIGHT BULBGenuine PIAA product
H4 platinum competition bulb, unique gas mix and glass tube
colour enable equivalent output of 150 watts on dip and main
beam while only drawing 80/80 watts
Supplied individually H89 (single)
£205
£875
£650
£35
£830
£185
£105
£2,195
£45
£275
£980
£1,865
£1,645
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
R4 KIT 6 - 1 - 1
LANCER EVOLUTION X R4 KIT
Front suspension
- subframe, lower arm assembly, ARB links, damper top mounts
- gearbox mount bracket, centre-member reinforcement panel
Rear suspension
- subframe, upper arm assembly, camber rod assembly, toe rod assembly,
longitudinal rod assembly, ARB links, damper top mounts
Side impact protection kit (compulsory in FIA R4 category)
- door side impact absorbing foam, composite door cards
- polycarbonate side windows
Body
- front bumper support bar
- polycarbonate rear window
Interior
- composite dashboard
- heater
Dampers, steering knuckles, anti-roll bars are NOT supplied with the kit
Modifications to be done by OWN means
- spring housing modification front/rear
- side door panel modification
- bonnet and boot lid panel modification
- dashboard bracket removal
R4 KIT £20,500
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
R4 SUSPENSION FRONT 6 - 2 - 1
FRONT SUBFRAMER4 spec tubular steel crossmember
Fits to standard mounting points on body and takes original steering rack
Weighs 9.3 kg, saving 4.7 kg over the standard subframe
Requires use of R4 spec suspension arms
CE114-110
FRONT ARM ASSEMBLYR4 spec front suspension arm
Left-hand and right-hand parts sold separately
Fasteners not included
CE114-105 (LH)
CE114-108 (RH)
FRONT TOP MOUNTR4 spec front damper top mounts
Requires customer to modify front turrets
Left-hand and right-hand parts sold separately
CE114-104 (LH)
CE114-107 (RH)
FRONT ANTI-ROLL BAR LINKR4 spec front ARB link
Connects standard ARB to R4 spec suspension arm bracket
2'off required per car
CE114-109
£1,190
£1,190
£2,887
£385
£385
£315
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
R4 SUSPENSION REAR 6 - 2 - 2
REAR SUBFRAMER4 spec tubular steel crossmember
Fits to standard mounting points on body and takes original rear differential
Weighs 10.6 kg, saving 8.5 kg over the standard subframe
Requires use of R4 spec suspension arms
CE114-119
REAR UPPER ARMR4 spec rear suspension arm
Left-hand and right-hand parts sold separately
Fasteners not included
CE114-231 (LH)
CE114-230 (RH)
REAR LONGITUDINAL ARMR4 spec rear suspension arm
Left-hand and right-hand parts sold separately
Fasteners not included
CE114-113 (LH)
CE114-117 (RH)
REAR CAMBER ARMR4 spec rear suspension arm
2'off required per car
Fasteners not included
CE114-115
REAR TOE ARMR4 spec rear suspension arm
2'off required per car
Fasteners not included
CE114-112
REAR ANTI-ROLL BAR LINKR4 spec rear ARB link
Connects standard ARB to R4 spec suspension arm bracket
2'off required per car
CE114-204
REAR TOP MOUNTR4 spec rear damper top mounts
Fits to original rear turrets
2'off required per car
CE114-227
£2,887
£450
£529
£945
£344
£945
£529
£315
£364
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
R4 SUSPENSION BEARINGS 6 - 2 - 3
ROD END BEARINGRodobal RM..XE series rod end bearings
RM22XECO: front arm rear (2 per car), rear trailing arm front (2 per car)
RM22XECO
ROD END BEARINGRodobal RM..MTE series rod end bearings
RM16MTEX1.5: rear camber rod (2 per car), rear toe rod (2 per car)
RML16MTEX1.5: rear camber rod (2 per car), rear toe rod (2 per car)
RM16MTEX1.5
RML16MTEX1.5
SPHERICAL BEARINGRodobal RG..MTE series spherical bearings
RG14MTE.29: rear upper arm (6 per car), rear trailing arm rear (2 per car)
RG18MTE.35: front arm inner (2 per car), rear top mount (2 per car)
RG14MTE.29
RG18MTE.35
SPHERICAL BEARINGRodobal RG..SE series spherical bearing
RG22SE.CO: front top mount (2 per car)
RG22SE.CO
ROD END BEARINGAurora HXAM-T series rod end bearings
HXAM-7T: rear anti-roll bar link (2 per car)
HXAB-7T: rear anti-roll bar link (2 per car)
HXAM-7T
HXAB-7T
SPHERICAL BEARINGAurora HAB-T series spherical bearings
HAB-7TG: front anti-roll bar link (4 per car)
HAB-14T: front arm outer (2 per car)
HAB-7TG
HAB-14T
£65
£35
£65
£67
£96
£68
£68
£26
£22
£34
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
R4 BODY AND INTERIOR 6 - 3 - 1
COMPOSITE DASHBOARDR4 spec glass fibre dashboard
Weight 4.0 kg, flocked top, integrated heater ducting
Currently available in LHD version only
CE114-145
HEATER ASSEMBLYR4 spec windscreen heater
3-speed centrifugal blower, can be connected into standard heater loop
Supplied with 4-way electrical switch
Ducting to dashboard not included
CE114-147
HEATED WINDSCREENR4 spec heated windscreen
Direct replacement for original screen
Available in LHD and RHD versions
CE114-148 (LHD)
CE114-XXX (RHD)
POLYCARBONATE WINDOW KITR4 spec polycarbonate side door and rear window kit
To be used with side impact protection kit
CE114-151KIT
SIDE IMPACT PROTECTION KITR4 spec side impact protection foam Arpro and glass fibre door cards
Compulsory in FIA R4 category
Requires customer to modify side door inner panels and remove
side window regulators
CE114-122KIT (LHF)
CE114-127KIT (RHF)
CE114-132KIT (LHR)
CE114-138KIT (RHR) £875
£875
£875
£875
£250
£687
£470
£980
£470
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
INDEX 9 - 1 - 1
A Fire extinguisher, electrical 5-3-1 NACD hydraulic lines 2-2-3 Fire extinguisher, hand held 5-2-4 Number plates 5-1-1Air intake filter 1-5-1 First aid kit 5-2-4Air intake pipe 1-5-1 Flocking, dashboard 5-2-2 O
Anti roll bar, front 3-2-2 Fluid, ACD hydraulic 2-2-4 Oil cooler hoses, engine 1-2-1
Anti roll bar, rear 3-2-2 Fluid, steering rack 3-4-1 Oil cooler, engine 1-2-1
Footwell, co-driver 5-2-1 Oil filter, engine 1-2-1B Footwell, driver 5-2-1 Oil, differential 2-2-4Base car 0-3-1 Fuel lines 1-3-1 Oil, engine 1-2-1
Battery, gel 5-3-1 Fuel pump cover 1-3-1 Oil, gearbox 2-2-4
Bead blast, bodyshell 4-1-1 Fuel tank 1-3-1 Output shaft, front 2-2-2
Blanking panel, IP radio 5-2-1Bodyshell preparation 4-1-1 G P
Bonnet pints 5-1-1 Gear box assembly 2-2-1 Paint work, bodyshell 4-1-1Bracket, dashboard screen 5-2-1 Glass, rear 4-1-1Bracket, nut gun 5-2-1 Guard, propeller shaft 4-2-3 R
Bracket, trip meter 5-2-1 Guard, rear differential 4-2-3 R4 body and interior 6-3-1Brake bell 3-3-2 Guards, fuel tank 4-2-1 R4 kit, complete 6-1-1Brake booster adaptor 3-3-1 Guards, hydraulic pump 4-2-2 R4 suspension, bearings 6-2-3Brake caliper 3-3-2 Guards, rear bumper 4-2-2 R4 suspension, front 6-2-1Brake cooling ducts, front 3-3-2 Guards, rear suspension 4-2-2 R4 suspension, rear 6-2-2Brake disc 3-3-2 Guards, sill 4-2-1 Radiator cap, engine 1-4-1
Brake disc cover, rear 3-3-2 Guards, sump 4-2-1 Radiator hoses, engine 1-4-1
Brake fluid 3-3-3 Guards, underfloor 4-2-1 Radiator, engine 1-4-1
Brake kit, front 3-3-1 Restrictor, air intake 1-5-2
Brake kit, rear 3-3-2 H Roll cage 4-1-1Brake lines 3-3-3 Hand brake lever 3-3-1 Roll cage padding 5-2-4Brake master cylinder 3-3-1 Hand brake master cylinder 3-3-1 Roof vent 5-1-1Brake pads 3-3-3 Hand brake platform 3-3-1Brake proportioning valve 3-3-1 Harness cutter 5-2-4 S
Bushing, engine roll stop 3-2-2 Harnesses, seat 5-2-4 Screen, dashboard 5-3-2Bushing, front anti roll bar 3-2-3 Head gasket, engine 1-1-1 Seat mounts 5-2-3Bushing, front lower arm 3-2-2 Head studs, engine 1-1-1 Seats 5-2-3Bushing, rear anti roll bar 3-2-3 Homologation document 0-3-1 Shift light 5-3-2Bushing, rear differential 3-2-2 Hydraulic clutch, ACD 2-2-4 Spare wheel strap 5-2-3Bushing, rear top mount 3-2-2 Hydraulic pump, ACD 2-2-3 Spark plug 1-6-1
Bushing, rear trailing arm 3-2-2 Splitter, front bumper 4-2-1Bushing, rear upper arm 3-2-2 I Steering rack assembly 3-4-1
Impact wrench, battery 5-2-2 Steering rack hoses 3-4-1C Intercom 5-3-2 Steering rack oil pump 3-4-1Catalytic converter 1-5-2 Intercooler, air intake 1-5-1 Steering wheel 3-4-1Clutch cover 2-1-1 Steering wheel adaptor 3-4-1Clutch disc 2-1-1 J Steering wheel spacer 3-4-1Clutch feed pipe 2-1-1 Jack, hydraulic scissor 5-2-2 Sump guard 4-2-1Clutch m/c adaptor 2-1-1 Jack, hydraulic stick 5-2-3Clutch master cylinder 2-1-1 Jack, mechanical stick 5-2-3 TCon rod bolts, engine 1-1-2 Thermostat 1-4-1Connecting rods 1-1-1 L Top mount, front 3-2-1Console cover, floor 5-2-1 Light bulb, halogen 5-3-2 Top mount, rear 3-2-1Coolant, engine 1-4-1 Light pod, bonnet 5-3-2 Transfer box assembly 2-2-1
Liners, front wheel arch 4-2-2 Transfer box overhaul kit 2-2-2D Liners, rear wheel arch 4-2-2 Transfer shaft, centre diff 2-2-1
Damper assembly 3-2-1 Loom, auxiliary 5-3-1 Trip meter 5-3-2Differential assy, rear 2-2-3 Loom, bonnet light pod 5-3-2 Turbocharger 1-5-1Dog gear kit 2-2-1 LSD bearing, front 2-2-2 Turbocharger build 1-5-1
Door card, front 5-2-2 LSD bearing, rear 2-2-3 Turbocharger drain hose 1-5-1
Door card, rear 5-2-2 LSD cover, front 2-2-2 Turbocharger exhaust outlet 1-5-1Drive shaft, front 2-2-2 LSD crown bolt, front 2-2-2Drive shaft, rear 2-2-2 LSD spacer, front 2-2-1 W
LSD spacer, rear 2-2-3 Warning triangle 5-2-4E LSD, front 2-2-1 Wheel brace 5-2-2ECU map, ACD 2-2-4 LSD, rear 2-2-3 Wheel nuts 3-1-1ECU map, engine 1-6-1 Wheel studs 3-1-1ECU, ACD 2-2-4 M Wheels 3-1-1ECU, engine 1-6-1 Main studs, engine 1-1-2 Window vents, rear 5-1-1Engine assembly 1-1-1 Map light 5-3-2 Windscreen 4-1-1Engine build 1-1-1 Mirror cover, interior mount 5-2-2Exhaust system 1-5-2 Mirrors, door 5-1-1
Mount, engine 3-2-1F Mount, transmission 3-2-1Film, glass anti-shatter 5-2-4 Mud flaps 4-2-2
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
NOTES 9 - 2 - 1
+44 (0) 1327 702975
MITSUBISHI Lancer Evo X Group N and R4
MML Sports Price List Jan 17
NOTES 9 - 2 - 2
+44 (0) 1327 702975