F/2
CARATTERISTICHE DEL MOTOREMOTOR FEATURES
Roller ad alto rendimento perelevate prestazioni e durata.High-performance roller forimproved efficiency and life.
Viti del coperchio posteriore inacciaio ad alta resistenza per
sopportare gli sforzi indottidall'alta pressione.
High resistance stainless steelscrews capable of withstanding
the stress induced by highpressure.
Va l v o l e d i d r e n a g g i oincorporate: ricircolano alloscarico il fluido drenatointernamente.Built in check valves: to relievecase pressure to the lowpressure side of the motor.
Foro drenaggioposteriore per un
facile collegamento.Case drain at rear
(shown with plug).
Parapolvere per proteggere laguarnizione di tenuta dell'alberodalle impurità e guarnizione ditenuta ad alte prestazioni.Seal to protect the highpressure shaft seal from dustand debris.
Valvola distributrice radiale edalbero in un solo pezzo con
tolleranze ridotte al minimo perassicurare un drenaggio
ridotto.Spool valve integral to the
ouput shaft of new designfeatures optimizing clearancegeometry and so minimizing
the oil slippage.
CODICI DI ORDINAZIONEORDERING CODES
Motore / Motor Cilindrata / Displacement Flangia / Flange Albero / Shaft
100100160
NTN
C25C32C25
BRBRBR
Versione / Version
HPS
11 (8,5)3)
13 (10)3)
F/3
CARATTERISTICHE TECNICHETECHNICAL SPECIFICATIONS
Motore - TipoMotor - Type
Cilindrata geometricaGeometric displacement
(cm3/giro)(cu.cm./rev.)
Pressione max ingressoMax inlet pressure
(bar)
Pressione differenz. maxMax operating
differentialpressure (bar)
Coppia maxMax torque
(daNm)
Portata maxMax flow(l/min)
Velocità maxMax speed
(min -1)(rpm)
Potenza maxMax horsepower
(kw)
49
81,5
101,2
125,7
161,6
201
251,5
315
402
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
140175225
Cont.Int.1)
Peak2)
9,51216
Cont.Int.1)
4050
Cont.Int.1)
8151020
Cont.Int.1)
78,5
Motore - TipoMotor - Type
Cont.Int.1)
7,59,5
at. ¢p max.at. ¢p max.
BR 50
BR 80
BR100
BR130
BR160
BR200
BR250
BR315
BR400
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175 (140)3)
200 (175)3)
225
Cont.Int.1)
Peak2)
175 (115)3)
200 (140)3)
225
Cont.Int.1)
Peak2)
175 (90)3)
200 (120)3)
225
Cont.Int.1)
Peak2)
135 (70)3)
175 (100)3)
210
Cont.Int.1)
Peak2)
115 (55)3)
150 (85)3)
175
Cont.Int.1)
Peak2)
2021,525
Cont.Int.1)
Peak2)
242730
Cont.Int.1)
Peak2)
293336,5
Cont.Int.1)
Peak2)
37 (30)3)
41 (37)3)
45
Cont.Int.1)
Peak2)
Cont.Int.1)
Peak2)
Cont.Int.1)
Peak2)
Cont.Int.1)
Peak2)
43 (30)3)
49 (36)3)
55
53 (30)3)
60,5 (38)3)
67
51 (30)3)
63 (41)3)
75
58 (30)3)
69 (43)3)
80
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
6075
Cont.Int.1)
735920
Cont.Int.1)
590740
Cont.Int.1)
475595
Cont.Int.1)
370460
Cont.Int.1)
295370
Cont.Int.1)
235295
Cont.Int.1)
190235
Cont.Int.1)
145185
Cont.Int.1)
1315
Cont.Int.1)
1315
Cont.Int.1)
12,514,5
Cont.Int.1)
12,5 (10)3)
14 (12,5)3)
Cont.Int.1)
Cont.Int.1)
Cont.Int.1)
Cont.Int.1)
11 (7)3)
12,5 (8,5)3)
9 (5)3)
11 (6,5)3)
7,5 (4)3)
9 (6)3)
BR 50
BR 80
BR100
BR130
BR160
BR200
BR250
BR315
BR400
Cont.Int.1)
Peak2)
175200225
Max. press. di scaricocon drenaggio apertoMax. back pressure
with drain line(bar)
Coppia min.di spunto
Min. startingtorque(daNm)
Portatadi drenaggio4)
Oil flow in thedrain line4)
(l/min)
Pressione max.avviamento a avuoto
Max. starting pressure inunloaded conditions
(bar)
Velocitàminima5)
Min. speed5)
(giri/min) (rpm)
1) Le condizioni intermittenti non devono durare più del 10% ogni minuto. - Intermittent duty must not exceed 10% each minute.2) Le condizioni di picco non devono durare più del 1% di ogni minuto. - Peak duty must not exceed 1% each minute.3) I valori tra parentesi si riferiscono alla versione con albero C25/C25.4/SD25. - The values in brackets are referred to C25/C25.4/SD25 shaft.4) Viscosità dell'olio 37 cSt. - Oil Viscosity 37 cSt.5) Per impieghi a velocità inferiori o con carichi radiali consultare la S.A.M. Hydraulik for applications at lower rpm or at high radial loads pls. consult S.A.M. Hydraulik.
10
10
10
9
7
5
5
5
5
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
Peak2)
175200225
Cont.Int.1)
1618
at. ¢p max.at. ¢p max.
Cont.Int.1)
2022,5
at. ¢p max.at. ¢p max.
Cont.Int.1)
25,529
at. ¢p max.at. ¢p max.
Cont.Int.1)
31 (25)3)
36 (30)3)at. ¢p max.at. ¢p max.
Cont.Int.1)
39 (25)3)
45 (32)3)at. ¢p max.at. ¢p max.
Cont.Int.1)
49 (25)3)
56 (31)3)at. ¢p max.at. ¢p max.
Cont.Int.1)
47 (25)3)
61 (30)3)at. ¢p max.at. ¢p max.
Cont.Int.1)
51 (25)3)
67 (32)3)at. ¢p max.at. ¢p max.
at. ¢p = 100 barat. ¢p = 140 bar
0,71,6
at. ¢p = 100 barat. ¢p = 140 bar
0,71,6
at. ¢p = 100 barat. ¢p = 140 bar
0,71,6
at. ¢p = 100 barat. ¢p = 140 bar
0,71,6
at. ¢p = 100 barat. ¢p = 140 bar
0,71,6
at. ¢p = 100 barat. ¢p = 140 bar
1,53
at. ¢p = 100 barat. ¢p = 140 bar
1,53
at. ¢p = 100 barat. ¢p = 140 bar
1,53
at. ¢p = 100 barat. ¢p = 140 bar
1,53
10
10
10
10
10
10
10
10
10
F/4
Il diagramma è stato ottenuto conprove eseguite su un numerosignificativo di motori, utilizzandoun'olio avente una viscositàcinematica di 37 cSt allatemperatura di 45° C.
Curve according tests carried outwith a relevant number of motorsand using hydraulic oil withkinematic viscosity of 37 cSt at 45° Ctemperature.
PERDITE DI CARICO PER ATTRAVERSAMENTOPRESSURE LOSS
MASSIMA PRESSIONE AMMESSA SULLA GUARNIZIONE ALBEROMAX PERMISSIBLE SHAFT SEAL PRESSURE
Perdite di carico per attraversamento.Pressure loss in the motor.
Pressione massima di scarico senza drenaggio o massimapressione nella linea di drenaggio. I motori sono forniti nellaversione con guarnizioni standard (diagramma Standard) o nellaversione con guarnizioni ad alta pressione (diagramma HPS).La versione HPS è disponibile solo con alberi C25, C25.4, SD25.Per condizioni di pressione e velocità non contemplate dalpresente grafico si consiglia di contattare la S.A.M. Hydraulik.
Max. return pressure without drain line or max. pressure in thedrain line.Motor are supplied in standard seal version (Standard chart) orin HPS seal version (HPS chart).HPS version is availbale only for C25, C25.4 and SD25 shafts.For pressure and speeds not showed in the curve below, pleasecontact S.A.M. Hydraulik.
Standard HPS
F/5
MOTORE/MOTOR
A (mm)
A (in)
B (mm)
B (in)
Pesi - Weight (kg)
139.5
5.49
9
0.35
7.2
BR50
DIMENSIONI E PESIDIMENSIONS AND WEIGHT BR...N
BR80 BR100 BR130 BR160 BR200 BR250 BR315 BR400
145.5
5.73
15
0.59
7.5
149
5.87
18.7
0.74
7.7
153.5
6.04
23.2
0.91
8
160
6.30
29.6
1.17
8.3
167.5
6.59
37
1.46
8.6
176.5
6.95
46.1
1.81
9.1
188
7.40
57.7
2.27
9.8
184.5
7.26
54.4
2.14
10.1
ALBERO/SHAFT
C (mm)
C (in)
55.3
2.18
C25
55.3
2.18
C25.4
Per le dimensioni degli alberi vedere pagina F/9
For shafts dimensions see page F/9
N° 2 fori d'alimentazione G1/2" profondità filetto 18 mm [0.71 in]No. 2 G1/2" main parts; thread depth 18 mm [0.71 in]1
Drenaggio motore G1/4" profondità filetto 15 mm [0.60 in] Max. Non presente nella versione HPSG1/4" drain port; thread depth 15 mm [0.60 in] Max. Not in HPS version2
55.3
2.18
SD25
F/6
DIMENSIONI E PESIDIMENSIONS AND WEIGHT BR...T
ALBERO/SHAFT
C (mm)
C (in)
55.3
2.18
C25
55.3
2.18
C25.4
55.3
2.18
SD25
68.3
2.69
C32
59.1
2.33
C31.75
68.5
2.70
CN32
Per le dimensioni degli alberi vedere pagina F/9
For shafts dimensions see page F/9
MOTORE/MOTOR
A (mm)
A (in)
B (mm)
B (in)
Pesi - Weight (kg)
139.5
5.49
9
0.35
(7.3)1)
7.4
BR50 BR80 BR100 BR130 BR160 BR200 BR250 BR315 BR400
145.5
5.73
15
0.59
(7.6)1)
7.7
149
5.87
18.7
0.74
(7.8)1)
9
153.5
6.04
23.2
0.91
(8.1)1)
8.3
160
6.30
29.6
1.17
(8.4)1)
8.6
169.5
6.59
37
1.46
(8.7)1)
9
176.5
6.95
46.1
1.81
(9.2)1)
9.5
188
7.40
57.7
2.27
(9.9)1)
10.2
184.5
7.26
54.4
2.14
(10.2)1)
10.5
1) I valori tra parentesi si riferiscono alla versione con albero C25/C25.4/SD25. - The values in brackets are referred to C25/C25.4/SD25 shaft.
N° 2 fori d'alimentazione G1/2" profondità filetto 18 mmNo. 2 G1/2" main ports thread depth 0.70”1
Drenaggio motore G1/4" profondità filetto 15 mmG1/2" drain port thread depth 0.60”2
MOTORE/MOTOR
A (mm)
A (in)
B (mm)
B (in)
Pesi - Weight (kg)
181.5
7.03
46.1
1.81
9
F/7
144.5
5.60
9
0.35
7.1
BR50
DIMENSIONI E PESIDIMENSIONS AND WEIGHT BR...A
BR80 BR100 BR130 BR160 BR200 BR250 BR315 BR400
150.5
5.83
15
0.59
7.4
154
5.97
18.7
0.74
7.6
158.5
6.14
23.2
0.91
7.9
165
6.40
29.6
1.17
8.2
172.5
6.69
37
1.46
8.5
193
7.48
57.7
2.27
9.7
189.5
7.34
54.4
2.14
10
ALBERO/SHAFT
C (mm)
C (in)
49.4
1.94
C25
49.4
1.94
C25.4
49.4
1.94
SD25
Per le dimensioni degli alberi vedere pagina F/9
For shafts dimensions see page F/9
SPECIALE A RICHIESTA - SPECIAL ON REQUEST
N° 2 fori d'alimentazione G1/2" profondità filetto 18 mmNo. 2 G1/2" main ports thread depth 0.70
1
Drenaggio motore G1/4" profondità filetto 15 mmG1/2" drain port thread depth 0.60”2
N° 4 3/8” 16 UNC profondità filetto 17 mmNo. 4 3/8” 16 UNC thread depth 0.65”
3
F/8
MOTORE/MOTOR
A (mm)
A (in)
B (mm)
B (in)
Pesi - Weight (kg)
150.5
5.93
145
5.71
(7.2)1)
7.3
BR50
DIMENSIONI E PESIDIMENSIONS AND WEIGHT BRP
BR80 BR100 BR130 BR160 BR200 BR250 BR315 BR400
156.5
6.16
151
5.94
(7.5)1)
7.6
160
6.30
154.5
6.08
(7.7)1)
7.9
164.5
6.48
159
6.26
(8)1)
8.2
171
6.73
165.5
6.52
(8.3)1)
8.5
178.5
7.03
173
6.81
(8.6)1)
8.9
187.5
7.38
182
7.17
(9.1)1)
9.4
199
7.83
193.5
7.62
(9.8)1)
10.1
196
7.72
190.5
7.50
(10.1)1)
10.4
ALBERO/SHAFT
C (mm)
C (in)
55.3
2.18
C25
55.3
2.18
C25.4
55.3
2.18
SD25
68.3
2.69
C32
59.1
2.33
C31.75
68.5
2.70
CN32
Per le dimensioni degli alberi vedere pagina F/9
For shafts dimensions see page F/9
1) I valori tra parentesi si riferiscono alla versione con albero C25/C25.4/SD25. - The values in brackets are referred to C25/C25.4/SD25 shaft.
N° 2 fori d'alimentazione G1/2" profondità filetto 16 mmNo. 2 G1/2" main ports thread depth 0.63”1
Drenaggio motore G1/4" profondità filetto 15 mmG1/2" drain port thread depth 0.60”
Per le dimensioni non indicate fare riferimento al disegno delmotore BR...N o BR...TRefer to BR...N or BR...T motor drawings for any dimension here notindicated
2
SPECIALE A RICHIESTA - SPECIAL ON REQUEST
F/9
DIMENSIONIDIMENSIONS ALBERI / SHAFTS
ALBEROSHAFT C31.75
ALBEROSHAFT C25.4
ALBEROSHAFT SD 25 ALBERO
SHAFT C32
ALBEROSHAFT CN 32
SPECIALE A RICHIESTA - SPECIAL ON REQUEST
ALBEROSHAFT C25
SPECIALE A RICHIESTA - SPECIAL ON REQUEST
F/10
BR 50
BR 80
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
Intermittent pressure drop and oilflow must not occur simultaneusly.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
Intermittent pressure drop and oilflow must not occur simultaneusly.
F/11
BR 100
BR 130
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
Intermittent pressure drop and oilflow must not occur simultaneusly.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
Intermittent pressure drop and oilflow must not occur simultaneusly.
F/12
BR 160
BR 200
* Pressione massima continua perversione con albero Ø25.
** Pressione massimaintermittente per versione conalbero Ø25.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
* Constant maximum pressure forØ25 shaft model.
** Intermittent maximum pressurefor Ø25 shaft model.
Intermittent pressure drop and oilflow must not occur simultaneusly.
* Pressione massima continua perversione con albero Ø25.
** Pressione massimaintermittente per versione conalbero Ø25.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
* Constant maximum pressure forØ25 shaft model.
** Intermittent maximum pressurefor Ø25 shaft model.
Intermittent pressure drop and oilflow must not occur simultaneusly.
F/13
BR 250
BR 315
* Pressione massima continua perversione con albero Ø25.
** Pressione massimaintermittente per versione conalbero Ø25.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
* Constant maximum pressure forØ25 shaft model.
** Intermittent maximum pressurefor Ø25 shaft model.
Intermittent pressure drop and oilflow must not occur simultaneusly.
* Pressione massima continua perversione con albero Ø25.
** Pressione massimaintermittente per versione conalbero Ø25.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
* Constant maximum pressure forØ25 shaft model.
** Intermittent maximum pressurefor Ø25 shaft model.
Intermittent pressure drop and oilflow must not occur simultaneusly.
F/14
BR 400
* Pressione massima continua perversione con albero Ø25.
** Pressione massimaintermittente per versione conalbero Ø25.
Pressioni e portate superiori a quelleammesse in regime continuo nondevono essere applicatecontemporaneamente.
* Constant maximum pressure forØ25 shaft model.
** Intermittent maximum pressurefor Ø25 shaft model.
Intermittent pressure drop and oilflow must not occur simultaneusly.
CARICHI AMMESSI SULL’ALBEROSHAFT LOAD CAPACITY
Formula utilizzabile per il calcolo del carico radiale massimo ammissibile(Pr) ai vari numeri di giri, e alle varie distanze dalla flangia.
Calculating formula of max permissible radial load (Pr) accordingto rpm and distance from flange.
Pr = • [daN]800
n2190091 + L
n≥200 [giri/min] [RPM]L≤68.5 [mm]