NC Spot DrillsCorner Rounding Cutters& Engraving Tools
NO NEED TO CHOOSENINE9 DOES IT ALL!
Chamfering
Center Drilling
Spotting
Counter sinking
Facing Turning
Engraving
Corner Rounding
Grooving
2009
®
Various applications of NC Spot Drill
We Focus: ● Higher efficiency ● Long tool life● Position accuracy ● Total cycle time
Multifunctional Cutting Tool
A new concept of drilling !
Universal, Easy handlingand Material saving!One holder to cover somany different applications!
21st Century Ancient History
0.5xD of spotting.“The high performance solid carbide drill or HSS drill with web thinning do not need any centering!”“Drilling from solid!” most of the drills manufacturers and suppliers quote that.However, if you applied NC Spot Drill to drill a spot which is half of the drilling diameter, you can look forward to the following benefi ts.
Benefi ts: ● Higher feed rate of drill! Why? Because the drill is guided at the strongest part of cutting edge. ● Better center position of drill! Why? Because the spotting is done by single cutting edge which is out of center, and similar to boring operation. ● Increase the tool life of drill!
Without Spotting 0.5xD Spotting Larger Spotting
Best result!Higher speed and feed rate.More accuracy of positioning and diameter tolerance.
Less positional accuracy of drill, and diameter tolerance.Lower feed rate.Unstable tool life.
Longer spotting time!Guided at the weakestcorner of drill.Shorter tool life.
Mini SpottingThe application of the engraving insertas a spotting drill for the minor size of drill.
Benefi ts: ● Best positioning accuracy! ● Better surface with spotting by NC Spot drill in advance.
Working example of spotting:Spindle speed: 3000-25000 r.p.m. Feed rate: 0.0004~0.0008 inch/rev. Tool : 99616-3/8.08W NC40
Without Spotting With Spotting
1
NC Spot Drill with Patentedindexable carbide insert.High Effi ciency! Low Cost!CNC Lathes, CNC Turning Centers and Machining Centers.
One tool will perform multiple applications.● Long tool life.● Each insert has two or four cutting edges.● Suitable for spotting, chamfering, grooving and engraving.● 45° / 60° / 82° / 90° / 100° / 120° / 142° angle for different applications.● Increase cutting speed with coated carbide inserts.
NC Spot Drills
ALL IN ONE !!Turning Center
● Four in oneCNC Lathes
Machining Center
Rotary
Turning Turning
Rotary
Helical groove milling
Engraving
Grooving
Chamfer turning
Face grooving
Face groove milling
Internal turning
Spot drilling on end surface
Internal chamfering
Spot drilling
External and internalchamfering
Grooving
SpottingFacing
Engraving
ChamferingProfi le chamfering
Spotting
2
Holder
Engraving Tools
NC Spot Drill
Angle Inserts Dmin.
Dmax. Page
45° 99619-V045V04506T1W
0.45(0.018”) P5
99619-V06060° V06006T1W
2.7(0.106”)
P50.45(0.018”)
99616-10...SWN9MT080201W-60
1.1(0.043”) P100.25
(0.010”)
90°
99616-06-6 N9MT05T1
P146(0.236”)
1(0.039”)
99616-10...N9MT0802
P1510
(0.394”)
99616-14... N9MT11T3
P1614(0.551”)
3(0.118”)
60°99616-14...P60 N9MT11T3P60
6.2(0.244”) P112
(0.079”)
99616-13V V9MT12T3
P1213(0.512”)
2(0.079”)
90°99616-10...SW N9MT080201W
2.0(0.079”) P100.25
(0.010”)
99616-06-6N9MT05T1
P146(0.236”)
1(0.039”)
Spotting
Cham
fering
Grooving
Engraving
Drilling
99619-V082-3/8
99619-V082-5/8
82°
P139(0.354”)
V08212T3
P1314(0.551”)
V0820802
99616-22 N9MT1704
P1722(0.866”)
3(0.118”)
2.1(0.083”)
2(0.079”)
2(0.079”)
2(0.079”)
*Open circle = suitable application, Filled circle = preferred application.
NC Spot Drill Application System
3
NC Spot Drill
Center Drilling
Corner Rounding
99616-14...RC
P21
99616-CT
P8
HolderAngle Inserts Dmax. Page
P26
Spotting
Cham
fering
Grooving
Engraving
DrillingD
min.
R 1/64 R 1/8
1/8”7/64”
*ANSI STANDARD #3 AND #4
142°99619-V142
P732
(1.260”)2
(0.079”)
100°
90°
99616-20-100
P1916
(0.630”)
120°99616-20-120
P1917
(0.669”)
142°99616-20-142
P1918.5
(0.728”)
Special Application
60° Centeringand Engraving
Pitch 0.5-3mm threadturning external
Drilling and millinga groove
2mm grooving,depth 4 mm
8mm end milling,face milling(high postive)
Special requests are welcomed.
99616-25-CT28
N9MT11T3RC (2 cutting edges)
N9MT1103CT
V1421604
N9MT11T3CT2T-H
N9MT11T3CT2T-H
N9MT11T3CT2T-H
TCMT2204
P1825
(0.984”)4
(0.157”)
4(0.157”)
4(0.157”)
4(0.157”)
4
5
Patent Pending!Main Features
■ High Positive Rake AngleIndexable insert. Suitable for engraving all types of materials, such as plastic, non-ferrous metal, aluminum, carbon steel and stainless steel.
■ Multi-Side GrindingFull peripherally ground insert to ensure effi cient repeatability. It performs excellently without producing any burrs, especially in aluminum and stainless steel.
■ High Speeds, High Feed RatesDesigned to run at high speed, up to 20000 rpm. Feed rate 0.08mm (0.003”) / rev apply to aluminum; 0.05mm (0.002”) / rev apply to stainless steel. Reduces engraving cycle time!
■ EconomicalEach indexable insert has 2 cutting edges.No resharpening required. Tool length is unchanged. No need to reset after changing insert or cutting edge.Excellent repeatability!
■ ApplicationsUniversal for marking number and almost any character. 45° , 60° engraving inserts which can be used for marking serial numbers ; product codes ; dial scales ; signs ; logo outlines and almost any character which can be created by the NC programming system.
Ancient History
Engraving45°/60°
Our Claim: This is a revolutionary new concept of engraving tools with indexable carbide inserts.They offer you the ability to produce HIGH QUALITY ENGRAVING in most materials.The latest coated carbide grades help you to obtain higher speeds and feed rates,dramatically reducing your cycle times.
Engraving Tool V045 / V060
Low feedrate !
21st Century
6
45 60
Feature: ● For 45, 60 degree engraving tools. ● K20F submicron grain carbide insert, high positive rake angle and ground relief angle for universal applications. ● Each insert has 2 cutting edges.
NC2071: ● TiN coated. Good for low carbon steel, stainless steel, non-ferrous metal and aluminum.
NC2032: ● TiAlN coated. Good for all kinds of steel 30°-50° HRC, alloy steel and cast iron.
Parts No. Angle Grade CoatingDimensions
Wmin. Wmax.. Tmax.L S Re
V04506T1W06-NC207145° K20F
TiN6.35
(0.250”)2.0
(0.079”)0.2
(0.008”)0.45
(0.018”)2.1
(0.083”)2.0
(0.079”)V04506T1W06-NC2032 TiAlN
V06006T1W06-NC207160° K20F
TiN 6.35(0.250”)
2.0(0.079”)
0.2(0.008”)
0.45(0.018”)
2.7(0.106”)
2.0(0.079”)
V06006T1W06-NC2032 TiAlN
● Other sizes also available upon request.
Parts No. ød L Screw Key
99619-V045-06 6(0.236”)
40(1.575”) NS-22044
0.8NmNK-T7
99619-V060-06 6(0.236”)
40(1.575”)
● Other sizes also available upon request.
Starter Kit
Parts No. Angle Insert included Content
99619-V045-03K-7145°
V04506T1W06-2071
1 x holder+ 3 inserts+ 1 key
99619-V045-03K-32 V04506T1W06-2032
99619-V060-03K-7160°
V06006T1W06-2071
99619-V060-03K-32 V06006T1W06-2032
Inserts
Re=0.2 (0.008”) Re=0.2 (0.008”)
Indexable Engraving Tool 45°, 60°
ødød
ø6(0.236”)Holders
7
Feature: ● For spotting before drilling by 135° - 140° point angle high performance drill. ● 142 degree indexable spotting drills. Maximum diameter up to 32mm.
NC2071: ● K20F grade, TiN coated, high positive geometry, fully ground cutting edge and relief angle. ● Each insert has 2 cutting edges. ● Universal grade for all unhardened steel and cast iron.
V1420803-NC2071
V1421604-NC2071
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S Re
V1420803-NC2071 K20F TiN 8(0.315”)
2.38(0.094”)
0.8(0.031”)
16(0.630”)
2.8(0.110”)
V1421604-NC2071 K20F TiN 14(0.551”)
4.76(0.187”)
1.2(0.047”)
32(1.260”)
5.5(0.217”)
Parts No. Insert Type ød L Screw Key
99619-V142-5/8 V1420803-NC2071 5/8” 4” NS-30072 NK-T9
99619-V142-1.000 V1421604-NC2071 1” 4.75” NS-50125 NK-T20
Holders
Inserts
Feature:
● Using spotting fi rst may increase higher speed and feed rate of the after drills.● Saving total machining time !● Longer tool life of the after drills. Money saving !● Higher accuracy of positioning and diameter tolerance !
Starter Kit
Parts No. Insert Content
99619-142-5/8.08 2071 KIT(99619-V142-IN3)
V1420803-NC20711 x 5/8” holder3 x inserts1 x Key
Max
ø1.
260”
Max
ø0.
630”
ø5/8”
ø1”
NC2071
Feature: ● Very high cutting speed and feed rate.● Center drilling with indexable insert saves pre-setting time of tool change.● Create center holes similar to DIN 332 Form A and DIN 332 Form B. ( Match USA standard #3 & #4 Combined drills & Countersink) .● Carbide inserts provide for very long tool life.
NC2071: ● K20F grade, TiN coated, high positive ground cutting edge. ● Universal grade for carbon steel, alloy steel, stainless steel and cast iron. ● Each insert has 2 cutting edges.
Inserts
Parts No. Grade Coating ANSIDimensions
d1 d2 d3 b L1 (min.) L2 (min.)
N9MT1103CT278-NC2071K20F TiN
#3 7/64” 0.264” 0.472” 0.029” 0.275” 0.304”
N9MT1103CT318-NC2071 #4 1/8” 0.264” 0.472” 0.061” 0.290” 0.351”
Holders
Parts No. ød L Screw key
99616-5/8-CT1/8 5/8” 4” NS-300722.0 Nm NK-T9
Workpiece material Vc (sfm) f (in/rev.)Alloy steel 260 ~ 500 0.001 ~ 0.002Carbon Steel 260 ~ 500 0.001 ~ 0.002Stainless Steel 215 ~ 400 0.0008 ~ 0.0016
Cutting Data
High feedrate !Economical !
Low feedrate !Expensive !Form A Form B
Starter Kit
Parts No. Insert Content
99616-5/8.CT278 NC2071 KIT(99616-CT278-IN2)
N9MT1103CT278-NC2071 1 x holder+ 2 inserts+ 1 key99616-5/8.CT318 NC2071 KIT
(99616-CT318-IN2) N9MT1103CT318-NC2071
● Base RPM on d1.
● Tool center alignment critical, center height adjusting sleeve is available on request.
ø5/8”
8
Application Example:
21st Century
Ancient History
For CenteringReplace HSS center drillwith Carbide Insert Increase cutting speed by 30 times
● Contour Chamfering on Machining Center.
● Spotting, Grooving, Engraving on Machining Center.
● Turning, Chamfering, Facing on CNC Lathes.
● Center Drilling on Machining Center.
● 45°, 60° Engraving Tools.
■ Available shank diameter-Ø5, Ø6, Ø10, Ø12, Ø16, Ø20mm, Ø25mm, Ø1/4”, Ø3/8”, Ø1/2”, Ø5/8”, Ø3/4”■ Inserts are interchangeable.
Spotting, EngravingCenter Drilling Engraving 60°/90°
Centering, Turning Spotting, ChamferingGrooving
ChamferingCorner Rounding
New concept!New design!
● Cut a Serrated Workpiece.● Single Pass Each Direction.
Application Examples
9
60° / 90° SW
Features: ● 90° Indexable engraving insert with 4 cutting edges. ● No resharpening required. ● For marking all types of work pieces.
N9MT080201W-NC10 : ● Submicron carbide insert, TiAlN coated, for AI, AI-alloy, hardened steel 40-50°, Stainless steel.
N9MT080201W-NC40 : ● Submicron carbide insert, TiN coated, for all unhardened steel and cast iron, general purpose.
N9MT080201W-60-NC40 : ● Submicron carbide insert, TiN coated, very positive angle for 60° engraving for all kind of steel and cast iron.
21st Century
Ancient History
Parts No. Grade Coating Dimensions Dmax. Tmax.L S Re
N9MT080201W-60-NC40 60° K20F TiN
8(0.315”)
2.38(0.094”)
0.1(0.004”)
1.1(0.043”)
0.8(0.031”)
N9MT080201W-NC40 90° K20F TiN 2.0(0.079”)
0.9(0.035”)
N9MT080201W-NC10 90° K20F TiAlN 2.0(0.079”)
0.9(0.035”)
Holders
Inserts
Parts No. ød L Screw key
99616-10 10(0.394”)
90(3.543”)
NS-300552.0 Nm NK-T8
99616-3/8 3/8” 3.5”
● Total 2 inserts are equal to 8 engraving tools. Parts No. Insert Content
99616-10.08W NC10 KIT(99616-10-ME2SWAL) N9MT080201W-NC10
1 x 10mm holder + 2 inserts+ 1 key
99616-10.08W NC40 KIT(99616-10-ME2SW) N9MT080201W-NC40
99616-10.08W-60 NC40 KIT(99616-10-ME2SW-60) N9MT080201W60-NC40
99616-3/8.08W NC10 KIT(99616-10-IN2SWAL) N9MT080201W-NC10
1 x 3/8” holder + 2 inserts+ 1 key
99616-3/8.08W NC40 KIT(99616-10-IN2SW) N9MT080201W-NC40
99616-3/8.08W-60 NC40 KIT(99616-10-IN2SW-60) N9MT080201W60-NC40
ø10 (0.394”)ø3/8”
NC10
Re=0.1(0.004”)
Re=0.1(0.004”)
Re=0.1(0.004”)
NC40 60°-NC40
Engraving Tool
Wmax.
Starter Kit
10
Feature: ● Fully ground spotting insert, for 60 degree spotting and engraving.
NC40: ● P35 grade, TiN coated. ● Each insert has 2 cutting edges.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S Re
N9MT11T3P60-NC40 P35 TiN 11(0.433”)
3.97(0.156”)
0.8(0.031”)
6.2(0.244”)
4(0.157”)
Features:● 60 degree spotting drill with indexable insert. ● Using standard NC Spot Drill shank. ● A single cutting edge design creates higher precision and position when spotting.
Applications: ● For spotting, engraving, small grooving on milling machines, machining centers. ● For carbon steel, alloy steel and cast iron, general purpose.
Parts No. ød L Screw key
99616-14-1/2 1/2” 4“NS-350802.5 Nm NK-T15
99616-14-5/8 5/8” 4”
Dmax.
Tmax.
P60-NC40
Re=0.031”
NC Spot Drill-N9MT11T3P6060°
Holders
ø5/8”
Inserts
Max
ø0.
244”
11
Feature: ● 60 degree indexable spotting insert, Dmax 0.512”. ● Special geometry with supporting edges for using in high speed machining. ● Excellent tool for grooving, save machining time !
NC2071 : ● K20F grade, TiN coated, high positive ground cutting edge and relief angle. ● Universal grade for carbon steel, alloy steel and cast iron. ● Each insert has 2 cutting edges.
NC9076 : ● High positive geometry and sharpen edge. ● DLC coated, super good for Al, Al-alloy, copper, brass and bronze. ● Perform excellent surface on non-ferrous metal. ● Each insert has 2 cutting edges.
NC2071
NC9076
Dmax.
Tmax.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S Re
V9MT12T3CT-NC2071 K20F TiN12.7(0.5”)
3.97(0.156”)
0.8(0.031”)
13(0.512”)
11.7(0.461”)
V9MT12T3CT-NC9076 K20F DLC
Features: ● 60 degree spotting drill with indexable insert. ● A single cutting edge creates higher precision and position when spotting.
Applications:● Spotting, engraving, grooving and chamfering on milling machines, machining centers. ● Spotting, facing on CNC Lathes.
Parts No. ød L Screw Key
99616-13V-5/8 5/8” 4“ NS-350802.5 Nm NK-T15
Parts No. Insert Content
99616-13V-5/8.12 2071 KIT(99616-13V-IN3)
V9MT12T3CT-NC20711 x holder + 3 inserts+ 1 key
ø5/8”
Re=0.031”
Re=0.031”
NC Spot Drill-V9MT12T3 60°
Holders
Inserts
HOT
Max
ø0.
512”
Starter Kit
12
Feature: ● 82 degree indexable spotting insert. ● Match the geometry of Amercian standard screw hole. ● Special geometry with supporting edges for use in high speed machining.
NC2071 : ● K20F grade, TiN coated, high positive ground cutting edge and relief angle. ● Universal grade for carbon steel, alloy steel and cast iron. ● Each insert has 2 cutting edges.
NC9076 : ● High positive geometry and sharp edge. ● DLC coated, super good for Al, Al-alloy, copper, brass and bronze. ● Produces excellent surface fi nish on non-ferrous metals. ● Each insert has 2 cutting edges.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S Re
V0820802-NC2071 K20F TiN8
(0.315”)2.38
(0.094”)0.4
(0.016”)9
(0.354”)4.8
(0.189”)V0820802-NC9076 K20F DLC
V08212T3-NC2071 K20F TiN12.7(0.5”)
3.97(0.156”)
0.8(0.031”)
14(0.551”)
7.5(0.295”)
V08212T3-NC9076 K20F DLC
NC2071
NC9076
max.
Dmax.
Tmax.
Features: ● 82 degree spotting drill with indexable insert. ● Special cutting edge design gives higher precision and position when spotting
Applications: ● Spotting, engraving, grooving and chamfering on milling machines, machining centers. ● Spotting, facing on CNC Lathes.
Parts No. Insert type ød L Screw Key
99619-V082-3/8 V0820802 3/8” 3.5” NS-300552.0 Nm NK-T8
99619-V082-5/8 V08212T3 5/8” 4” NS-350802.5 Nm NK-T15
Inserts
Holders
NC Spot Drill-V0820802 / V08212T382°
Starter Kit
Re=0.031”
Re=0.031”
Max
ø0.
551”
Max
ø0.
354”
Parts No. Insert Content
99619-V82-5/8.12 2071 KIT(99619-V082-IN3)
V08212T3-NC20711 x 5/8” holder + 3 inserts+ 1 key
ø3/8”
ø5/8”
13
Features: Mini spotting drill with indexable insert, low cutting power required. Especially good for Swiss type automatic lathes and CNC lathes.
NC2071 : ● K20F grade, TiN coated, fully ground cutting edge and relief angle. ● Geometry with supporting edges to stable the cutting condition on low power machine. ● Each insert has 2 cutting edges, for carbon steel, alloy steel and cast iron.
NC9076 : ● High positive geometry and sharp edge. ● DLC coated, super good for Al, Al-alloy, copper, brass and bronze. ● Produces an excellent surface fi nish on non-ferrous metal. ● Each insert has 2 cutting edges.
Inserts
NC2071
NC9076
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S Re
N9MT05T1CT-NC2071 K20F TiN5
(0.197”)1.8
(0.071”)0.2
(0.008”)6
(0.236”)3.5
(0.138”)N9MT05T1CT-NC9076 K20F DLC
HoldersFeatures: ● Smallest indexable spotting drill holder. ● A single cutting edge creates higher precision and position when spotting.
Applications: ● Spotting, engraving, and chamfering on milling machines, machining centers. ● Spotting, facing on CNC Lathes.
Parts No. ød L Screw key
99616-06-6 6(0.236”)
35(1.378”)
NS-200360.8 Nm NK-T699616-06-5 5
(0.197”)
99616-06-1/4 1/4”
ø5 (0.197”)ø6 (0.236”)ø1/4”
Re=0.2 (0.008”)
Re=0.2 (0.008”)
NC Spot Drill-N9MT05T1 90°
Mini SpottingMini Spotting
Starter Kit
Parts No. Insert Content
99616-06-1/4.05 2071 KIT(99616-06-IN6)
N9MT05T1CT-NC20711 x 1/4” holder + 6 inserts+ 1 key
Max
ø0.
236”
14
H-NC40 : ● Best choice for spotting application. ● Special geometry with supporting edges for use in high speed machining. ● Sharp edge good for long cutting chip metals, such as low carbon steel, stainless steel and Ti, Ti-alloy. ● Each insert has 2 cutting edges. H-NC9076 : ● High positive geometry and sharp edge. DLC coated, super good for Al, Al-alloy, copper, brass and bronze. ● Produces excellent surface fi nish when chamfering non-ferrous metals. ● Each insert has 2 cutting edges.NC40 : ● General purpose, universal grade for all unhardened steel and cast iron. ● Each insert has 4 cutting edges.NC10 : ● High positive angle and fully ground cutting edge and relief angle. ● Universal grade for Al, Al-alloy, non-ferrous metal and stainless steel. ● Each insert has 4 cutting edges.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S ReN9MT0802CT2T-H-NC40 K20F TiN
8(0.315”)
2.38(0.094”)
0.8(0.031”) 10
(0.394”)4
(0.157”)
N9MT0802CT2T-H-NC9076 K20F DLCN9MT080208CT-NC40 K20F TiNN9MT080204CT-NC40 K20F TiN 8
(0.315”)2.38
(0.094”)0.4
(0.016”)N9MT080204CT-NC10 K20F TiAlN
Features: ● Indexable spotting drill holders. ● Single cutting edge design gives higher precision when spotting.Applications: ● Spotting, engraving, grooving and chamfering on milling machines, machining centers. ● Spotting, facing on CNC Lathes.
Parts No. ød L Screw Key
99616-10 10(0.394”)
90(3.543”) NS-30055
2.0 Nm NK-T899616-3/8 3/8” 90
(3.543”)
H-NC40
H-NC9076
NC40
NC10
5 Pcs-Pack
Parts No. Insert included Content
99616-3/8.08 NC40 KIT(99616-10-IN6)
N9MT080208CT-NC40 1 x 3/8” holder + 6 inserts + 1 key
Re=0.8 (0.031”)
Re=0.8 (0.031”)
Re=0.4 (0.016”)Re=0.8 (0.031”)
Re=0.4 (0.016”)
NC Spot Drill-N9MT080290°
Inserts
Holders
● Selected package for starter who wants to try NC Spot Drill.● Included one insert on tool holder and 5 inserts in the pocket. ● Total 6 inserts are equal to 24 spot drills.
● Economy pack for larger end users.● Do not miss it !
Shank Parts No. Contents
3/8 99616-3/8 PACK 5 x 3/8” holders+ 1 key
~ Special ~ Special Offer ~ Offer ~~ Special Offer ~
Ø10 (0.394”)Ø3/8”
Starter Kit
Max
ø0.
394”
15
5 Pcs-Pack
H-NC40
Re=0.031”
H-NC9076
Re=0.031”
NC Spot Drill-N9MT11T3 90°
● Economy pack for larger end users.● Do not miss it !
Starter Kit
H-NC40 : ● Best choice for spotting application. ● Special geometry with supporting edges for use in high speed machining. ● Sharp edge good for long cutting chip metals, such as low carbon steel, stainless steel and Ti, Ti-alloy. ● Each insert has 2 cutting edges. H-NC9076 : ● High positive geometry and sharp edge same as grade H-NC40. DLC coated, super good for Al, Al-alloy, copper, brass and bronze. ● Produces excellent surface fi nish when chamfering non-ferrous metals. ● Each insert has 2 cutting edges. NC40 : ● General purpose, universal grade for all unhardened steel and cast iron. ● Each insert has 4 cutting edges.NC10 : ● High positive angle and fully ground cutting edge and relief angle. ● Universal grade for Al, Al-alloy, non-ferrous metal and stainless steel. ● Each insert has 4 cutting edges. NC60 : ● Cermet insert, fully ground cutting and relief angle, for hardened steel up to HRC55. ● Each insert has 4 cutting edges.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S ReN9MT11T3CT2T-H-NC40 K20F TiN
11(0.433”)
3.97(0.156”)
0.8(0.031”)
14(0.551”)
7(0.276”)
N9MT11T3CT2T-H-NC9076 K20F DLCN9MT11T3CT-NC40 P35 TiN
N9MT11T3CT-NC10 K10F TiAlN 0.3(0.012”)
N9MT11T3CT-NC60 CERMET 0.8(0.031”)
Features: ● Indexable insert spotting drill holders. ● The most wide range application of spotting drills for milling and turning operation. ● Holders and inserts are interchangeable. Applications: ● Spotting, engraving, grooving and chamfering on milling machines, machining centers. ● Spotting, facing, turning on CNC Lathes.
Parts No. ød L Screw Key
99616-14-1/2 1/2” 4“ NS-350802.5 Nm NK-T15
99616-14-5/8 5/8” 4”
NC40
Re=0.031”
NC10
Re=0.012”
NC60
Re=0.031”
Inserts
Holders-90°
Ø1/2”Ø5/8”
Parts No. Insert included Content99616-14-1/2.11 NC40 KIT(99616-14-1/2-IN6) N9MT11T3CT-NC40
1 x 1/2” holder + 6 inserts + 1 key
99616-14-1/2.11 NC10 KIT(99616-14-1/2-IN6AL) N9MT11T3CT-NC10
99616-14-1/2.11 NC60 KIT(99616-14-1/2-IN6HS) N9MT11T3CT-NC60
99616-14-5/8.11 NC40 KIT(99616-14-IN6) N9MT11T3CT-NC40
1 x 5/8” holder + 6 inserts + 1 key
99616-14-5/8.11 NC10 KIT(99616-14-IN6AL) N9MT11T3CT-NC10
99616-14-5/8.11 NC60 KIT(99616-14-IN6HS) N9MT11T3CT-NC60
Shank Parts No. Contents
5/8” 99616-14-5/8 PACK 5 x 5/8” holders+ 1 key
Max
ø0.
551”
16
Feature: ● 90 degree indexable spot drill insert, Dmax 0.87 inch.
NC2071: ● K20F grade, TiN coated, high positive geometry, fully ground cutting edge and relief angle. ● Each insert has 2 cutting edges. ● Universal grade for all unhardened steel and cast iron.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S Re
N9MT1704CT-NC2071 K20F TiN 17(0.669”)
4.76(0.187”)
1.2(0.047”)
22(0.866”)
10(0.394”)
NC2071
Features: ● 90 degree spotting drill with indexable insert. ● A single cutting edge creates higher precision and position when spotting.
Applications: ● Spotting, engraving, grooving and chamfering on milling machines, machining centers. ● Spotting, facing on CNC Lathes.
Parts No. ød L Screw Key
99616-22-3/4 3/4” 4”NS-501255.5 Nm NK-T20
99616-22-1 1” 6”
Parts No. Insert fi tted Content
99616-22-3/4.17 2071 KIT(99616-22-IN3)
N9MT1704CT-NC20711 x 3/4” holder+ 3 inserts+ 1 key
Ø3/4”
Re=0.047”
NC Spot Drill-N9MT170490°
Inserts
Holders
Starter Kit
ShankØ3/4”
ShankØ1”
Max
ø0.
866”
17
Feature: ● For spotting diameter up to 1 inch. ● Fully ground cutting edge and relief angle.
NC40: ● P35, TiN coated. ● Universal grade for carbon steel, alloy steel and cast iron. ● Each insert has 3 cutting edges.
Parts No. Grade CoatingDimensions
Dmax. Tmax.L S
TCMT220408CT-NC40 P35 TiN 20.83(0.820”)
4.76(0.187”)
25(0.984”)
12.2(0.480”)
NC40
Features: ● Large spotting diameter with indexable insert. ● Single cutting edge design gives high precision when spotting.
Applications: ● Spotting, and chamfering on milling machines, machining centers.
Parts No. ød L Screw Key
99616-1-CT28 1” 4.72” NS-401003.8 Nm NK-T15
Ø1”
1.181”
NC Spot Drill-TCMT2204 90°
Inserts
Holders
Max
ø0.
984”
ø0.1
57”
18
● For spotting before drilling by 118° point angle drill.● 60° chamfering.
● For aircraft 100° normal rivet hole and screw hole.
L
Max
ø0.
630”
ød
● For spotting before drilling by 135~140° point angle high performance drilling.
Feature: ● Special geometry with supporting edges to reduce the vibration in high speed machining.
H-NC40 : ● K20F grade, TiN coated. ● General purpose for all kinds of steel and cast iron. ● Each insert has 2 cutting edges. H-NC9076 : ● High positive geometry and sharp edge . ● DLC coated, specially developed for Al, Al-alloy, copper, brass and bronze. ● Produces excellent surface fi nish when chamfering non-ferrous metals. ● Each insert has 2 cutting edges.
H-NC40
H-NC9076
Parts No. Grade CoatingDimensions
L S Re
N9MT11T3CT2T-H-NC40 K20F TiN11
(0.433”)3.97
(0.156”)0.8
(0.031”)N9MT11T3CT2T-H-NC9076 K20F DLC
Re=0.031”
Re=0.031”
100°/120°/142° NC Spot Drill-N9MT11T3CT
Inserts
● 100 degree ● 120 degree ● 142 degree
L L
Max
ø0.
669”
Max
ø0.
728”
ød
ød
19
Features: ● Indexable insert spotting drill holders for 100°/120°/142° spotting. ● Reduces spotting time, increase tool life and position accuracy of the next drilling operation.
Parts No. Angle ød L Screw Key Dmax. Tmax.
99616-3/4-100 100°
3/4” 4” NS-350802.5 Nm NK-T15
16(0.630”)
6(0.236”)
99616-3/4-120 120° 17(0.669”)
5(0.197”)
99616-3/4-142 142° 18.5(0.728”)
3(0.118”)
Ø3/4”
Ø3/4”
Ø3/4”
Starter Kit-100°/120°/142°
Parts No. Insert included Content
99616-3/4-100.11 NC40 KIT(99616-3/4-100H-IN6)
N9MT11T3CT2T-H-NC40
1 holder+ 6 inserts+ 1 key
99616-3/4-120.11 NC40 KIT(99616-3/4-120H-IN6)
99616-3/4-142.11 NC40 KIT(99616-3/4-142H-IN6)
100°/120°/142°NC Spot Drill-N9MT11T3
Holders-100°/120°/142°
Higher feed rate !
Better center position !
Longer tool life !
20
21
Features:● Higher cutting speed and feed rate.● Various corner radius inserts can fi t on same holder.● Combination corner rounding and 45° chamfering application on same insert.● Carbide insert can stand very long tool life.
N9MT11T3RCXX-NC40 ● Submicron carbide insert, K20F, TiN coated, universal design for all kinds of materials.● Inserts are CNC ground for precision radius location. ● Each insert has two cutting edges.
Parts No. Grade Coating Corner radius(R)
offset DimensionsX Y Z L S
N9MT11T3RC10-NC40 K20F TiN 1.0 2.75(0.108”)
1.5(0.059”)
2.5(0.098”)
11(0.433”)
3.97(0.156”)
N9MT11T3RC15-NC40 K20F TiN 1.5 3.25(0.128”)
1.5(0.059”)
3(0.118”)
11(0.433”)
3.97(0.156”)
N9MT11T3RC20-NC40 K20F TiN 2.0 3.75(0.148”)
1.5(0.059”)
3.5(0.138”)
11(0.433”)
3.97(0.156”)
N9MT11T3RC25-NC40 K20F TiN 2.5 4.25(0.167”)
1.5(0.059”)
4(0.157”)
11(0.433”)
3.97(0.156”)
N9MT11T3RC30-NC40 K20F TiN 3.0 4.75(0.187”)
1.4(0.055”)
4.4(0.173”)
11(0.433”)
3.97(0.156”)
N9MT11T3RC1/64-NC40 K20F TiN 1/64 0.086” 0.059” 0.0747” 0.433” 0.156”
N9MT11T3RC1/32-NC40 K20F TiN 1/32 0.101” 0.059” 0.090” 0.433” 0.156”
N9MT11T3RC1/16-NC40 K20F TiN 1/16 0.133” 0.059” 0.122” 0.433” 0.156”
N9MT11T3RC3/32-NC40 K20F TiN 3/32 0.164” 0.059” 0.153” 0.433” 0.156”
N9MT11T3RC 1/8-NC40 K20F TiN 1/8 0.199” 0.055” 0.180” 0.433” 0.156”
Features:
● For corner rounding using NC Spot Drill shank.● Good for small work pieces.● Same insert can also be used to produce a 45 degree edge chamfer.
Parts No. ød L Screw Key
99616-14-1/2 1/2” 4” NS-350802.5 Nm NK-T15
99616-14-5/8 5/8” 4”
Corner Rounding CutterRC
Inserts
Holders
● Other sizes also available upon request.
21st Century
Ancient History
Ø1/2”, Ø5/8”
Engraving depth “ t ”
Eng
ravi
ng w
dith
“ w
”
Cutting Data
● The bottom of the engraving is fl at, minimum engraving depth (t) of 0.05 mm (0.002”) is recommended.
● To use the engraving chart, select your engraving width (w) on the vertical axis. Select your engraving insert angle (45° or 60°), and follow the horizontal line from the (w) axis to the intersection with the insert angle. Follow the vertical line from this intersection point to the engraving depth (t) axis to determine the engraving depth.
Attention!1. Setting-up the tool holder: ● The engraving tool shank runout should be below 0.02 mm (0.0008”). Shrink fi t chucks, hydraulic chuck and high precision spring collet chucks are recommended. ● Pre-balance the tool holder: G6.3/10,000 R.P.M. is recommended.
2. Clamping the engraving insert: Place and hold the insert in the insert pocket against the positioning side. See illustration below:
3. Selecting the speed and feed rate: Select the spindle speed and feed rate according to the selected material’s cutting data. The downward feed rate of the Z-axis should be reduced to 50-70% of the table feed rate.
4. Cutting fl uid and cooling condition: ● Elmusion is recommended for engraving on steel, stainless steel, Al and Al-alloy. ● Blown cooled air is recommended for engraving on cast iron and plastic.
Work Material S RPM f (in/rev.) Grade of InsertStainless Steel 5000~20000 0.0008~0.0020 NC2071
Steel< 30˚HRC 5000~20000 0.0008~0.0020 NC207130˚-50˚HRC 5000~20000 0.0004~0.0008 NC2032
Cast iron 5000~20000 0.0004~0.0008 NC2032Aluminum, Non-Ferrous Metal 5000~20000 0.0008~0.0030 NC2071
PMMA, POM (Plastic) 5000~20000 0.0008~0.0030 NC2071
Depth / Width Chart Instructions and Cutting Data of Engraving Tools
22
Depth of Spotting “ t ”
Dia
met
er o
f Spo
tting
“ d
”
1. From Spot diameter “d” to get drill depth “ t ”.2. Point angle “α” is decided by which tool holder you use.3. From “d” draw a horizontal line to get intersection of the line by point angle “α”.4. From the intersection draw a vertical line to the bottom to have depth of spotting “ t ”. “ t ” is the drill depth of the NC program.5. The sectional view of spotting will depend on the shape of insert, NC40 and other grade of inserts have different sectional view.6. For chamfering, do not use tip of insert, 1mm(0.04”) minimum clearance is required for a smooth surface fi nish.
1. Using your “d” value and cutting speed SFM from the data sheet (reference page 24), calculate spindle speed “S”(RPM).2. Feed rate per minute F=f x S=RPMxIPR
inchF=fxS
SFM X 3.82D
D= Diameter -inchS= Spindle speed -r.p.m.SFM= Cutting Speed -inch/min.f = inch/rev. =IPRF= inch/min.
S=
Diameter/Depth Chart and Speed/Feed Rate Calculation of NC Spot Drill
Instruction of Use
Calculate Spindle Speed
23
Determine spindle speed and feed rate: ● Choose spotting depth to decide spotting diameter according to the Diameter/Depth chart of page 23. ●The spindle speed should be calculated by the maximum diameter of spotting, chamfering and grooving.
Work Material SFM IPR (inch/rev.) Grade of Insert
Carbon Steel 500~820 0.0020~0.0040 NC40, H-NC40
Alloy Steel 330~660 0.0016~0.0024 NC40, H-NC40
Stainless Steel 210~410 0.0010~0.0024 NC10, NC60, H-NC40
Non-Ferrous Metal (Al, copper) 500~1050 0.0020~0.0040 NC10, H-NC9076
Cast iron 260~500 0.0020~0.0040 NC10, NC40
Ti, Ti-alloy 200~260 0.0012~0.0024 H-NC40
Work Material SFM IPR (inch/rev.) Grade of Insert
Carbon Steel 500~820 0.0020~0.0040 NC40, H-NC40
Alloy Steel 330~660 0.0016~0.0024 NC40, H-NC40
Stainless Steel 210~410 0.0010~0.0024 NC10, NC60, H-NC40
Non-Ferrous Metal (Al, copper) 500~1050 0.0020~0.0040 NC10, H-NC9076
Cast iron 260~500 0.0020~0.0040 NC10, NC40
Ti, Ti-alloy 200~260 0.0012~0.0024 H-NC40
* For technical construction reasons, the insert is not located on the center of the holder.* Inserts with supporting edges can increase feed rate 50%. (ex:NC2071, NC9076, H-NC40 type)
Work Material SFM IPR (inch/rev.) Grade of Insert
Carbon Steel 500~1050 0.0020~0.0040 NC40, H-NC40
Alloy Steel 330~820 0.0016~0.0024 NC40, H-NC40
Stainless Steel 210~410 0.0010~0.0024 NC10, NC60, H-NC40
Non-Ferrous Metal (Al, copper) 500~1050 0.0020~0.0040 NC10, H-NC9076
Cast iron 500~820 0.0020~0.0040 NC10, NC40
Ti, Ti-alloy 200~260 0.0012~0.0024 H-NC40
* NC2071, NC9076, H-NC40 type can increase feed rate 20%.
Engraving: Width of engraving=diameter of cutting=”d” Depth of engraving=depth of cutting=”T”
■For α = 90° insert, d=2xT ■For α = 60° insert, d=1.73xT
Work Material SFM IPR (inch/rev.) Grade of Insert
All Kind of Steel, unhardened, Cast iron 66~260 0.0004~0.0008 NC40
Non-Ferrous Metal 66~310 0.0004~0.0008 NC10
Hardened SteelHRC 40-50° 66~260 0.0004~0.0008 NC10
Attention:The calculated result “d” is only for calculation of spindle speed.
NC Spot Drill Cutting DataN9MT-CT Insert
Centering
Chamfering
Grooving
Multi-function Insert
N9MT-W Insert Engraving Insert
24
Determine spindle speed and feed:To decide running speed of the tools and feed rate, please calculate spindle speed andfeed rate according to the following formula and cutting data:
d = 2 x X inchd = 2 x r inch
SFM X 3.82d S= r.p.m.
F = f x S inch
d = diameter of the tool for calculation purposeX = tool radius offset (ref. page 21 for RC inserts)r = tool radius offset SFM = cutting speed inch/minS = Spindle speedF = Feed ratef = inch/rev.
TL=TL’-Y, H = X or r
X = tool radius offset (ref. page 21 for RC inserts)r = tool radius offset Y = distance to the center of radius. (page 21 for RC inserts)TL’ = tool lengthTL = tool length offsetH = tool radius offset
RC Insert
Recommanded cutting speed for different materials:
Workpiece material SFM IPR (inch/rev.) Grade of insert
Carbon Steel 260~500 0.0020~0.0040 NC40
Alloy steel 260~500 0.0020~0.0040 NC40
High alloy steel 260~500 0.0016~0.0040 NC40
Hardened steel <HRC40° 200~260 0.0016~0.0040 NC40
Stainless steel 200~330 0.0020~0.0040 NC40
Gray cast iron 260~500 0.0020~0.0040 NC40
Aluminum, AI-alloy Si < 12% 500~1050 0.0020~0.0040 NC40
Al-alloy Si >12% 500~820 0.0020~0.0040 NC40
Copper 660~820 0.0020~0.0040 NC40
Brass and Bronze 500~820 0.0020~0.0040 NC40
Corner Rounding Tool Cutting Data
N9MT-RC Insert Corner Rounding Tool
Calculate spindle speed
Calculate tool length offest on machining center
Corner Rounding RC Insert
25
Special
8 mm end milling, face milling(High postive)
2 mm grooving, depth 4 mm Drilling and milling a groove
Pitch 0.5-3 mm thread turningexternal
Ordering Code Various Applications
N9MT11T3FH-NC2031 8 mm end milling, face milling(High postive)
N9MT11T3T-NC2031 Pitch 0.5-3 mm thread turningexternal
N9MT11T3G-NC2031 2 mm grooving, depth 4 mm
N9MT11T3E-NC2031 Drilling and milling a groove
*Special insert and holder are available on request.
Special Request Form for NC Spot Drills
□Spotting □Drilling□Chamfering
□Milling
□Engraving
□Turning
Dia: Length: Shank:
□Facing
□Others:
Job:
Holder:
Working Material : ISO code or DIN code:
Sketch of working pieces:
26
EVEREDE TOOL CO.5296 Northwest Highway Chicago, Illinois 60630 Phone: (773) 467-4200 Toll Free: (800) 621-5486 www.everede.net
Distributor:
2009.03. Cat. No.: NNS 11 US : 5000 PC