These instructions do not supersede local, state, or federal
regulations.
JOB NAME:
MEETING DATE:
REVIEWED SDS # SUBJECT:
MEETING DOCUMENTATION:
Pneumatic tools are powered by compressed air, usually from an air
compressor. Common examples include nail guns, staple guns, drills,
hammers, chippers, grinders, and sanders. There are many dangers
associated with pneumatic tools: getting hit by a disconnected air
hose, getting hit by an attachment or a fastener, tripping over an
air hose, hazardous noise levels from tools and compressors, and
hazards created by dust and flying chips.
Pneumatic tools require special precautions:
• Connect safety devices when you are hooking up air hoses. You
need to prevent air hoses from whipping around and causing injury
or damage if they accidentally come uncoupled. Use a short wire or
positive locking device to attach the hose to the tool and to serve
as a safeguard.
• Identify all pneumatic tools that shoot nails, rivets, staples,
or similar fasteners, and operate at pressures of more than 100
pounds per square inch. These tools must have special safety
devices that prevent fasteners from being ejected unless the muzzle
is pressed against the work surface.
• Be sure that a safety clip or retainer clip is installed to
prevent attachments (like the chisel on a chipping hammer) from
being accidentally ejected while the tool is being used.
Follow these safe work practices: • Never point a pneumatic tool at
anyone.
• Never carry a tool with your finger on the trigger.
• Keep hoses from creating tripping hazards.
• Make sure you know what is on the other side of a wall before
pulling the trigger of a nail gun. You don’t want the nail to go
all the way through and hit a person or a gas line.
• Protect your hearing from the noise produced by pneumatic tools.
Wear the appropriate hearing protection.
• Wear eye and face protection to protect yourself from chips,
fasteners, and other flying objects.
• Set up screens around chippers, rivet guns, sta- plers, and air
drills to protect nearby workers from being hit by flying
fragments.
• Never use a tool unless you have been trained to use that
specific tool. If you have questions, ask your supervisor before
you start work.
• Never leave a nail gun unattended.
When you are using any kind of tool, from a screwdriver to a cement
mixer, to a pneumatic nail gun, it’s important that you: 1) always
select the proper tool for the job, 2) be sure the tool is in good
working condition, 3) use the tool according to the manufacturer’s
instructions, and 4) maintain and store the tool properly when
you’re done.
SAFETY REMINDER
Never use compressed air to clean your skin or clothes.
Pneumatic Tools
PO Box 700 Frankfort, IL 60423
815-464-0200 www.safetymeetingoutlines.com
815-464-0200 www.safetymeetingoutlines.com
Weekly Safety Meetings
Pneumatic Tools 1. The dangers associated with pneumatic tools
include:
a. getting hit by a disconnected air hose. b. tripping over an air
hose. c. hazardous noise levels. d. all of the above.
2. Which of the following actions can increase your chances of
suffering
or causing an accident or injury when working with pneumatic
tools?
a. wearing eye and face protection. b. connecting safety devices
when you are hooking up air hoses. c. carrying a tool with your
finger on the trigger. d. installing a safety clip or retainer
clip.
4. You need to make sure you know what is on the other side of a
wall
before pulling the trigger of a nail gun because you want to:
a. make sure no one is on the other side in case the nail goes
through. b. make sure there is nothing more interesting going on
there. c. be sure there is a gas line on the other side. d. have
something to aim for on the other side in case the nail goes
through.
3. True or False? You should never point a pneumatic tool at
anyone.
5. True or False? Hearing protection is not necessary when you
use
pneumatic tools.
CORRECTED ANSWER: __________
MY ANSWER: __________
CORRECTED ANSWER: __________
MY ANSWER: __________
CORRECTED ANSWER: __________
MY ANSWER: __________
CORRECTED ANSWER: __________
MY ANSWER: __________
CORRECTED ANSWER: __________
MY ANSWER: __________
Typewritten Text
TRAINER/SUPERVISOR: I conducted the safety meeting and administered
this quiz. I explained the correct answers and answered or noted
every attendee’s questions. Signature
____________________________________ EMPLOYEE: I understand the
material covered in this week’s safety meeting and this quiz. I’ve
written in the correct answers for the questions I initially missed
and understand why they are correct. Signature
____________________________________
PO Box 700 Frankfort, IL 60423
815-464-0200 www.safetymeetingoutlines.com
Weekly Safety Meetings
Pneumatic Tools 1. The dangers associated with pneumatic tools
include:
a. getting hit by a disconnected air hose. b. tripping over an air
hose. c. hazardous noise levels. d. all of the above.
2. Which of the following actions can increase your chances of
suffering
or causing an accident or injury when working with pneumatic
tools?
a. wearing eye and face protection. b. connecting safety devices
when you are hooking up air hoses. c. carrying a tool with your
finger on the trigger. d. installing a safety clip or retainer
clip.
4. You need to make sure you know what is on the other side of a
wall
before pulling the trigger of a nail gun because you want to:
a. make sure no one is on the other side in case the nail goes
through. b. make sure there is nothing more interesting going on
there. c. be sure there is a gas line on the other side. d. have
something to aim for on the other side in case the nail goes
through.
3. True or False? You should never point a pneumatic tool at
anyone.
5. True or False? Hearing protection is not necessary when you
use
pneumatic tools.
There are many dangers associated with pneumatic tools: getting hit
by a disconnected air hose, getting hit by an attachment or a
fastener, tripping over an air hose, hazardous noise levels from
tools and compressors…
Never carry a tool with your finger on the trigger.
You don’t want the nail to go all the way through and hit a person
or a gas line.
Never point a pneumatic tool at anyone.
Wear the appropriate hearing protection.
FURTHER DISCUSSION:
SUPERVISOR/TRAINER NOTES:
Answer Key
These instructions do not supersede local, state, or federal
regulations.
Las herramientas neumáticas funcionan con aire comprimido,
generalmente proveniente de un compresor de aire. Algunos ejemplos
comunes incluyen pistolas de clavos, pistolas de grapas, taladros,
martillos, martillos cinceladores, esmeriladoras, y lijadoras. Hay
muchos peligros asociados con las herramientas neumáticas: ser
golpeado por una manguera de aire desconectada, ser golpeado por un
accesorio o por un sujetador, tropezarse con una manguera de aire,
niveles peligrosos de ruido de las herramientas y compresores, así
como los peligros creados por el polvo y las desportilladuras
lanzadas al aire.
Las herramientas neumáticas requieren de precauciones
especiales:
• Conecte los dispositivos de seguridad al enganchar las mangueras
de aire. Usted necesita evitar que las mangueras se azoten y causen
una lesión o daño si accidentalmente se desenganchan. Use un cable
corto o dispositivo de cierre positivo para sujetar la manguera a
la herramienta y para que sirva como un resguardo de
seguridad.
• Identifique todas las herramientas neumáticas que disparan
clavos, remaches, grapas, o sujetadores similares y que operen a
presiones de más de 100 libras por pulgada cuadrada. Estas
herramientas deben contar con dispositivos especiales de seguridad
que eviten que los sujetadores sean lanzados a menos que la boca
del equipo sea presionada con la superficie de trabajo.
• Asegúrese que haya un sujetador de seguridad o sujetador de
retención instalado para prevenir que los accesorios (como el
cincel en un martillo cincelador) sean lanzados accidentalmente
mientras la herramienta está siendo usada.
Siga estas prácticas de seguridad en el trabajo:
• Nunca apunte una herramienta neumática hacia otra persona.
• Nunca cargue una herramienta con su dedo en el gatillo.
• No deje que las mangueras creen peligros de tropezones.
• Asegúrese de saber lo que hay del otro lado de la pared antes de
apretar el gatillo de una pistola de clavos. Usted no quiere que un
clavo pase totalmente al otro lado y le pegue a una persona o a una
tubería de gas.
• Proteja su audición del ruido producido de las herramientas
neumáticas. Use la protección correspondiente para la
audición.
• Use protección para los ojos y cara para protegerse de
desportilladuras, sujetadores y otros objetos lanzados por la
máquina.
• Coloque pantallas alrededor de los martillos cinceladores,
pistolas de remaches, engrapadoras y barrenas neumáticas para
proteger a los trabajadores cercanos de ser golpeados por
fragmentos lanzados al aire.
• Nunca use una herramienta a menos que haya recibido entrenamiento
en cómo usar esa herramienta en particular. Si tiene preguntas,
hable con su supervisor antes de comenzar el trabajo.
• Nunca deje desatendida una pistola de clavos.
Cuando esté usando cualquier clase de herramienta, incluyendo
destornilladores, mezcladoras de cemento y pistolas neumáticas de
clavos, es importante que usted: 1) siempre seleccione la
herramienta correcta para el trabajo correspondiente, 2) asegúrese
que la herramienta esté en buenas condiciones, 3) use la
herramienta de acuerdo a las instrucciones del fabricante, y 4)
mantenga y almacene la herramienta correctamente al terminar.
SAFETY REMINDER
Nunca use aire comprimido para limpiar su piel o ropa.
Herramientas neumáticas (Pnuematic Tools)
REVIEWED MSDS # SUBJECT:
PO Box 700 Frankfort, IL 60423
815-464-0200 www.safetymeetingoutlines.com
815-464-0200 www.safetymeetingoutlines.com
Weekly Safety Meetings
Herramientas neumáticas 1. Los peligros asociados con herramientas
neumáticas incluyen:
a. ser golpeado por una manguera de aire desconectada. b. tropezar
con una manguera de aire. c. niveles peligrosos de ruido. d. todas
las respuestas anteriores.
2. ¿Cuál de las siguientes acciones puede aumentar su posibilidad
de
sufrir o causar un accidente o lesión al trabajar con las
herramientas
neumáticas?
a. usar protección para los ojos y cara. b. conectar los
dispositivos de seguridad cuando está conectando las
mangueras de aire. c. cargar una herramienta con su dedo en el
gatillo. d. instalar un sujetador de seguridad o sujetador de
retención.
4. Usted necesita saber lo que hay del otro lado de la pared antes
de
apretar el gatillo de una pistola de clavos porque usted
quiere:
a. asegurarse que no hay nadie del otro lado en caso de que el
clavo atraviese la pared.
b. asegurarse que no hay otras cosas más interesantes sucediendo
allí. c. asegurarse que hay una línea de gas en el otro lado. d.
tener algo en qué apuntar en el otro lado en caso de que el
clavo
pase al otro lado.
3. ¿Verdadero o Falso? Usted nunca debe apuntar una
herramienta
neumática hacia otra persona.
5. ¿Verdadero o Falso? La protección para la audición no es
necesaria
cuando usted usa herramientas neumáticas.
RESPUESTA CORRECTA: __________
MI RESPUESTA: __________
RESPUESTA CORRECTA: __________
MI RESPUESTA: __________
RESPUESTA CORRECTA: __________
MI RESPUESTA: __________
RESPUESTA CORRECTA: __________
MI RESPUESTA: __________
RESPUESTA CORRECTA: __________
MI RESPUESTA: __________
Typewritten Text
ENTRENADO/SUPERVISOR: Yo lleve a cabo la junta de seguridad reparti
este examen. Explique la respuesta correcta y conteste o anote cada
pregunta de los asistentes presentes. Firma
___________________________ EMPLEADO: Entiendo el material cubierto
en la junta de seguridad de esta semana y en este examen. He
llenado las respuestas correctas de toda pregunta que inicialmente
tuve mal y entiendo la razon de la repuestas de las correcta. Firma
___________________________
FrontDesk
815-464-0200 www.safetymeetingoutlines.com
Weekly Safety Meetings
Herramientas neumáticas 1. Los peligros asociados con herramientas
neumáticas incluyen:
a. ser golpeado por una manguera de aire desconectada. b. tropezar
con una manguera de aire. c. niveles peligrosos de ruido. d. todas
las respuestas anteriores.
2. ¿Cuál de las siguientes acciones puede aumentar su posibilidad
de
sufrir o causar un accidente o lesión al trabajar con las
herramientas
neumáticas?
a. usar protección para los ojos y cara. b. conectar los
dispositivos de seguridad cuando está conectando las
mangueras de aire. c. cargar una herramienta con su dedo en el
gatillo. d. instalar un sujetador de seguridad o sujetador de
retención.
4. Usted necesita saber lo que hay del otro lado de la pared antes
de
apretar el gatillo de una pistola de clavos porque usted
quiere:
a. asegurarse que no hay nadie del otro lado en caso de que el
clavo atraviese la pared.
b. asegurarse que no hay otras cosas más interesantes sucediendo
allí. c. asegurarse que hay una línea de gas en el otro lado. d.
tener algo en qué apuntar en el otro lado en caso de que el
clavo
pase al otro lado.
3. ¿Verdadero o Falso? Usted nunca debe apuntar una
herramienta
neumática hacia otra persona.
5. ¿Verdadero o Falso? La protección para la audición no es
necesaria
cuando usted usa herramientas neumáticas.
Hay muchos peligros asociados con las herramientas neumáticas: ser
golpeado por una manguera de aire desconectada, ser golpeado por un
accesorio o por un sujetador, tropezarse con una manguera de aire,
niveles peligrosos de ruido de las herramientas...
Nunca cargue una herramienta con su dedo en el gatillo.
Usted no quiere que un clavo pase totalmente al otro lado y le
pegue a una persona o a una tubería de gas.
Nunca apunte una herramienta neumática hacia otra persona.
Use la protección correspondiente para la audición.
FURTHER DISCUSSION:
SUPERVISOR/TRAINER NOTES:
Answer Key
CENov16-PM_465988 4
:
bŸ@UÇ0ÜÉÆ2C-ÞŠb”{:
f:
q: