"POSI-TRAC"
RING DRIVE SILO
UNLOADER
OWNER'S MANUAL
230 Industriel Blvd, Saint-Germain
Quebec, Canada
J0C 1KO
Tel.: (819) 395-4282
Fax: (819) 395-2030
www.valmetal.com
TABLE OF CONTENT
Safety ...............................................................................................................................................1
Safety precautions ..........................................................................................................................2
DANGER: Silo gas is deadly!.......................................................................................................3
General information ......................................................................................................................4
Operation ........................................................................................................................................5
Operating the silo unloader...............................................................................................5
Lowering blower spout ......................................................................................................5
Maintain proper operating conditions .............................................................................6
Raising the unloader ..........................................................................................................6
Operating the winch to raise the unloader ......................................................................8
Setting up the unloader for unloading .............................................................................9
Starting to unload ..............................................................................................................9
Adjustments..................................................................................................................................10
Set counterweights ...........................................................................................................10
Adjust blower spout .........................................................................................................10
Adjust frost cutter clearance...........................................................................................10
Tension drive belts ...........................................................................................................11
Set guide wheel .................................................................................................................11
Set pressure on tension wheel .........................................................................................11
Adjust drive sprocket & dollie rollers............................................................................11
Adjust slip clutch pressure & drive chain .....................................................................12
Lubrication ...................................................................................................................................12
Trouble shooting ..........................................................................................................................13
Installation ....................................................................................................................................14
Install tripod .....................................................................................................................14
Install worm gear hoist VM-2125 ...................................................................................16
Install worm gear hoist motorisation .............................................................................17
Install unloader ................................................................................................................18
Repair parts ..................................................................................................................................33
TT, Rad; Revised 2006-03-01
INSTALL WORM GEAR HOIST VM-2125
TT, PT, Rad; Revised 2007-10-12 Page 16
INSTALL WORM GEAR HOIST MOTORISATION
TT, PT, Rad; Revised 2007-10-12 Page 17
"POSI-TRAC"
RING DRIVE SILO
UNLOADER
PARTS MANUAL
230 Industriel Blvd, Saint-Germain
Quebec, Canada
J0C 1KO
Tel.: (819) 395-4282
Fax: (819) 395-2030
www.valmetal.com
STANDARD TRIPOD PARTS
KEY PART NO# REQ'D DESCRIPTION KEY PART NO# REQ'D DESCRIPTION 1 00393 2 Secondary Leg 12' (8'2") 4 00413 3 Pin Safety
00394 2 Secondary Leg 14' (9'6") 5 B814HC5PST 2 Bolt 5/8 x 2 ¾ Special Shank 00395 2 Secondary Leg 16' (10'4") 6 N8HCCP 4 Nut 5/8 C/Lock 00396 2 Secondary Leg 18' (11'6") 7 00419 2 Cable Pulley 00397 2 Secondary Leg 20' (12'10") 8 00415 1 Tri-Plate Pulley Weldment 00399 2 Secondary Leg 24' (15'6") 9 00409 1 Tri-Plate Pulley Assembly 00402 2 Secondary Leg 30' (20'5") 10 B809HC5B 3 Bolt 5/8 x ½
2 00421 1 Main Leg Assy 12' 11 W8LP 3 Lockwasher 5/8 00422 1 Main Leg Assy 14' 00423 1 Main Leg Assy 16' 00424 1 Main Leg Assy 18' 00425 1 Main Leg Assy 20' 00427 1 Main Leg Assy 24' 00430 1 Main Leg Assy 30'
PART NO# DESCRIPTION 00967 12' Tri-Pod Assy Complete 00968 14' Tri-Pod Assy Complete 00969 16' Tri-Pod Assy Complete 00970 18' Tri-Pod Assy Complete 00971 20' Tri-Pod Assy Complete
PART NO# DESCRIPTION 02364 22' Tri-Pod Assy Complete 00972 24' Tri-Pod Assy Complete 02366 26' Tri-Pod Assy Complete 02367 28' Tri-Pod Assy Complete 02368 30' Tri-Pod Assy Complete
TT, PT, Rad; Revised 2008-11-05 34
TT, Rad; Revised 2006-03-01
WORM GEAR HOIST #VM-2125
KEY PART # DESCRIPTION 1 VS-2132 Hoist drum assembly 2 40-242824 Oilite bushing 1½" x 1¾" x 1 ½" 3 VS-2129 Bearing (oilite bushing included) 4 VS-2128 Base 5 VS-2161 Housing 6 40-242824 Oilite bushing 1½" x 1¾" x 1½" 7 VS-2162 Worm gear 8 VS-2164 Cover 9 39-25627 Oil seal
10 94-1460-98 Snap ring 11 40-15101 Bearing 12 40-15245 Cup 13 VS-2140 Spacer 14 VS-2166 Snap ring 15 VS-2192 Shaft 16 VS-2193 Worm 17 VS-2149 Crank 18 VS-2153 Pulley 19 VS-2155 Brake mount 20 VS-2154 Belt brake
KEY PART # DESCRIPTION 21 VS-2100 Hoist mount chanel 22 VS-2160 Socket head cap screw 5/16 x 1/2 23 94-110 Plug 3/8-14 npt 24 94-060 Oil level 25 94-110 Plug 3/8-14 npt 26 02C46-0020 5/16" x 1" square head setscrew 27 --- #8 x 3/4 Round head machine screw 28 02C22-0006 #8 washer 29 02C07-0013 #8 nut 30 99-380 3/8 x 3/8 x 1½ key 31 VS-2194 Spring 32 99-173 1/2" x 1" hex. bolt 33 99-343 1/2" washer 34 99-353 1/2" lock washer 35 99-143 3/8" x 1" hex. bolt 36 99-352 3/8" lock washer 37 99-299 "U" bolt 1/2" 38 01C69-0140 1/8" x 1" cotter pin
TT, PT, Rad; Revised 2008-11-05 35
MOTORIZED WORM GEAR HOIST
1
4 3 9
6
13 7 5 9 8
10 14 12
16 8
20 15 10 22
11 21
19 18
17
KEY PART # DESCRIPTION 1 VM-2125-SEUL Worm gear hoist 2 VS-2118 Shield brace 3 VS-2102 Reversing switch 4 VS-2115-99 Jack shaft ¾″ ∅ 5 17-041-.75 3/4 hp motor 6 VS-2112-99 Auxiliary shaft support 7 VS-2110 Locking bolt 8 40-EFL-12J Bearing 9 40-FL4 Flange
10 VS-2119 Shield bracket 11 99-338 Washer SAE 13/16 12 60-35B15-.75 Sprocket 35-B-15 x ¾ 13 60-35B72-1 Sprocket 35-B-72 x 1 14 60-35-94 Roller chain 15 VS-2120 Shield 16 41-MA100-.75 Pulley MA100 x ¾ 17 42-A38 Belt A38 18 41-4-2 Step pulley 19 VS-2107-99 Motor mount pin 3/8″ ∅ 20 VS-2117 Shield mount 21 VS-2108 Tension rod 22 VS-2106 Motor mount 23 VM-2164 Motor guard (incl. guard bracket CV-4423) (option) 24 CV-4423 Guard bracket (option)
TT. PT, Rad; Revised 2008-11-05 36
29
BLOWER SPOUT AND DOOR ARM
38
39
30 35 36
24 25
23
21
37
23
35 27 18
28
9 28
7 19 15
20
15 13
12 16
14
10
KEY PART NO# REQ'D DESCRIPTION KEY PART NO# REQ'D DESCRIPTION
1 00001 1 Spout Assembly 12' - 14' (72") 18 00040 2 Yoke Bushing 00004 1 Spout Assembly 16' (84") 19 P414K 1 Pin Buttonhead 00006 1 Spout Assembly 18' (95") 20 P#16E 1 Hair Pin 01407 1 Spout Assembly 20' (108") 21 00339 1 Torque Arm Weldment 12'-24' (26") 00773 1 Spout Assembly 24' (120") 01334 1 Torque Arm Weldment 30' (90") 00808 1 Spout Assembly 30' (192") 22 B609HC5B 2 Bolt ½ x 1 ½ 2 P109B 2 Cotter Pin 3/16 x 1 ½ 23 W6LP 2 Washer ½ Lock 3 02710 1 Spout Holder 24 W6FP 2 Washer ½ Flat 4 02711 2 Spout Holder Bracket 25 00040 2 Yoke Bushing 5 W4FP 4 Washer 3/8 Flat 26 B407HC5P 2 Bolt 3/8 x 1 6 N4HCCP 4 Nut 3/8 Unc 27 00008 1 Collector Ring Comp 3 Ring 1 Phase7 S607SS5CP 2 Set Screw ½ x 1 Sh 00581 1 Collector Ring 3-Phase 8 00361 1 Spout Brkt Pipe F 12'-16' 28 00336 2 Door Arm Tube 12'-24' (70")
00362 Spout Brkt Pipe F 18'-30' 01729 2 Door Arm Tube 30' (67") 9 00302 1 Door Arm 5' (12'-14') 29 B617HC5P 2 Bolt ½ x 3 ½
01843 1 Door Arm 6' (16') 30 00520 3 Cord Holder Assembly 00303 1 Door Arm 7' (18'-24') 31 00003 1 Spout Liner SS 01404 1 Door Arm 8' (30') 32 B408HC5P 2 Bolt 3/8 x 1 ¼ 10 00452 1 Hole Bracket 33 S102THFP 4 Screw #10-32 x 3/8 11 B627HC5P 1 Bolt ½ x 6 HH NC 34 N1HFP 4 Nut #10-32 12 00307 1 Door Arm Shaft Assy 12' (30") 35 02757 2 Torque Arm Mtg Ear Assy 00308 1 Door Arm Shaft Assy 14' (42") 36 02111 1 Short Spout Galv. 00309 1 Door Arm Shaft Assy 16' (48") 37 B607HC5P 4 Bolt ½ x 1 00310 1 Door Arm Shaft Assy 18' (60") 38 00523 1 Cable Spool Universal 00311 1 Door Arm Shaft Assy 20' & 30' (72") 39 00524 1 Hitch Pin W/Clip 00313 1 Door Arm Shaft Assy 22' 24' (96") 41 VS-3129 1 Adjusting Handle 13 00330 1 Door Arm Bracket 42 03935 1 Spout Support Stabilizer Kit 14 B619HC5P 1 Bolt ½ x 4 42a 03934 1 Spout Support Stblzr Slide Tube 15 N6HCP 6 Nut ½ 42b 03933 1 Spout Support Stblzr Tube 16 B413HC5P 4 Bolt 3/8 x 2 ½ 43 N6HCCP 1 Nut ½ CL 17 W4LP 4 Washer 3/8 Lock
Posi-Trac; Revised 2008-11-05 37
38 00044 3 Connector 3/16 Hole Elect 39 01960 1 Serial # Sticker - 2 ¾ In. 40 S103RFP 1 10-32 x ½ RHMS P 41 W6LP 4 Washer ½ Lock 42 B608HC5P 4 Bolt ½ x 1 ¼ 43 N4HCP 4 Nut 3/8 HX NC 44 50326 1 Grounding Strap (3-Phase) 45 00029 1 Grounding Strap (1-Phase)
HANSON TWIN-TRAC, POSI-TRAC COLLECTOR RING
KEY PART NO# REQ'D DESCRIPTION
00008 Colletor Ring Comp 3 Ring 1 Phase 00581 Collector Ring 3-Phase
1 00768 1 Serial # Plate 2 00023 1 Gasket, Serial # Plate 3 00010 1 Casting Machined Top 4 Z2TA 2 Zerk 45 Deg. ¼-28 Grease 5 02495 3 Connector ¼ Hole Elec. (1 Phase)
02495 8 Connector ¼ Hole Elec. (3 Phase) 6 00013 1 Ring Holder Plastic Machined 7 00014 1 Ring Assy Large (3-Ring) 8 00017 1 Ring Assy Medium (3-Ring) 9 00019 1 Ring Assy small (3-Ring) 10 00057 1 Gasket Felt 11 00011 1 Casting Machined Bottom 12 01445 1 Retainer Ring Machined 13 MPS 1 Pipe Strap ¾" (1-Phase)
MPS1 1 Pipe Strap 1" (3-Phase) 14 00056 1 Brush Holder Cover 15 00051 1 Cord Bottom 6/3 1-Phase (42.5")
02490 1 Cord Bottom 6/4 3-Phase (42") 16 00055 3 Copper Tabs 17 00049 6 Brush 18 00050 1 Brush Holder Box (3 Ring) 19 01984 1 Cord Connector 1 x ¾ W/T
01985 1 Cord Connector 1 x 7/8 W/T (3-Phase) 20 01845 1 Cord Top 6/3 1-Phase (42.5")
00709 1 Cord Top 6/4 3-Phase (42") 21 S102RFP 6 RHMS #10-32 x 3/8 22 B414HC5P 4 Bolt HHCS 3/8 x 2 ¾ 23 W4LP 4 Washer 3/8 Lock 24 N1HFBR 6 Nut #10-32 Brass 26 M209BR 3 Bolt Stud ¼ x 1 ½ Brass 27 N2HCBR 6 Nut ½ Brass 28 S104RFBR 6 RHMS #10-32 x 5/8 29 Z2TS 2 Zerk ¼-28 Threaded
39
1 20 21 2
42 41
5 24
19 28 43
27 3
26
45
6
30 44
28
7
8
9
10
11 29
17
33 13
30 00802 1 Ring Holder Kit 31 00801 1 Brush Holder Assembly 32 S202RCP 2 RHMS ¼ x 3/8 33 S108RFBR 3 RHMS #10-32 x 1 ¼ 34 02829 1 Bearing Collector Ring
18 31 40 16
24 16
24
32 14
38
15
34
12
23
4 22
TT, PT; Revised 2008-11-05 38
HANSON 3-24 BLOWER ASSEMBLY
KEY PART NO# REQ'D DESCRIPTION
02566 Complete Blower Assembly 1 02565 1 Blower Shell 24 Wldmnt 2 02569 1 Blower Insert Weldmnt 24 3 02567 1 Blower Base Weldmnt 24 HR 4 00998 1 Rotor 3-24 Machined 5 00863 3 Paddle, Machined 6 00845 3 Pin 1 Inch Paddle 24-28 Blwr 7 00870 AR Washer 1 x 14 Ga 8 P2RPG 6 Roll Pin ¼ x 1 3/8 9 S504SSCB 1 Set Screw 10 00874 AR Machinenry Bushing
01308 AR Shim washer 11 03545 1 Blower shaft 12 K315S 1 Key 5/16 sq x 3 13 01662 1 Flangette Outside w/Notch 14 01661 1 Flangette Inside w/Notch 17 00954 2 Bearing w/LC. Collar 1 3/8 18 B406HC5P 8 Bolt 3/8 x 7/8 19 W4LP 8 Washer 3/8 Lock 20 N4HCP 12 Nut 3/8 21 B406HF5P 6 Bolt 3/8 x 7/8 Unf 22 N4HTF8P 6 Nut 3/8 Top Lock 23 00077 1 Flangette Inside W/O Zerk 24 00078 1 Flangette Outside W/O Zerk 25 B411CC5P 4 Bolt 3/8 x 2 Crg 26 00887 2 Lifting Strap 27 N8HCCP 2 Nut 5/8 Clock
TT, PT, Rad; Revised 2006-03-01
39
HANSON 3-28 BLOWER ASSEMBLY
Pillow Block Enduro Thro
1A 8
1B 2 5
6
3 4
9 7
18 10
12
11
17
15 14
20 20 13 16
19
KEY PART NO# REQ'D DESCRIPTION 03550 Complete PB Blower 03549 1 Blower Shell Wldmt 28 Enduro
1A N8HCCP 2 Nut 5/8 Lock 1B 00887 2 Lifting Strap 2 01775 1 Blower Top, Insert Weldmnt 28 (including item 1A & 1B) 3 03622 1 Blower Base Weld Enduro 28 (including item 13 & 20) 4 03249 1 Rotor 3/28 Machined 5 00863 3 Paddle, Machined 6 00951 3 Pin Kit (including item 7 & 8)
00845 3 Pin 1 Inch Paddle 24-28 blwr 7 00870 AR Washer 1 x 14 Ga 8 P2RPG 6 Roll Pin ¼ x 1 3/8 9 S504SSCB 1 Set Screw
10 00831 2 Small Spacer 11 03545 1 Blower Shaft 12 K315S 1 Key 5/16 x 3 13 B408HC5P 4 Bolt 3/8 x 1 ¼ 14 W6LP 4 Washer ½ Lock 15 B607HC5P 4 Bolt ½ x 1 16 04634 AR Shim .025" 17 40-HCPA207-22 2 P.B. Bearing Complete 18 B406HC5P 8 Bolt 3/8 19 W4LP 8 Washer 3/8 Lock 20 N4HCP 8 Nut 3/8
TT, PT, Rad; Revised 2007-10-12 40
MOTOR MOUNT AND DRIVE
KEY PART NO# REQ'D DESCRIPTION
2 41-4B46-SD 1 Pulley Motor, 4B46 3 41-SD-1.125 1 Hub SD-1 1/8 (5 & 7 ½ HP)
41-SD-1.375 1 Hub SD 1 3/8 (10 HP) 4 42-B79 2 Belt B79 (for 28" Blower TT, PT)
42-B76 2 Belt B76 (for 24" Blower TT, PT) 42-B87 2 Belt B87 (for 28" Blower Rad) 42-B83 2 Belt B83 (for 24" Blower Rad)
5 42-B43 2 Belt B43 6 00191 1 Shield, Main Belt Guard (TT, PT)
01152 1 Shield, Main Belt Guard (Rad) 7 03364 1 Decal New Hanson Sticker
02251 1 Decal Belt Guard Warning 8 00446 2 Main Belt Buard Bracket 9 B307HC5P 6 Bolt 5/16 x 1 10 W3LP 6 Washer 5/16 Lock 11 N3HCP 6 Nut 5/16 Hx 12 B609HC5P 2 Bolt ½ UNC x 1 ½ 13 N6HCP 4 Nut ½ UNC 14 W6LP 2 Washer ½ Lock 16 B409HC5P 1 Bolt 3/8 x 1 ½ 17 B408HC5P 3 Bolt 3/8 x 1 ¼ 18 W4FP 4 Washer 3/8 Flat 19 W4LP 4 Washer 3/8 Lock 20 N4HCP 8 Nut 3/8 UNC 21 S613SSCP 2 Set Bolt ½ x 2 ½ SH 22 00193 1 Motor Plate Assembly 23 41-2B80-SK 1 Pulley 2B80 24 41-SK-1.375 1 Hub SK 1 3/8 25 41-2B60-SDS 1 Pulley Transmission, 2B60 26 41-SDS-1 1 Hub SDS 1 27 00197 1 Belt Tightener Tension Tab
TT, PT, Rad; Revised 2008-11-05 41
HEX ARMS, DRIVE RING & MAIN SUPPORTS
KEY PART NO# REQ'D DESCRIPTION 1 03443 1 Hex Arm Right 12'-24'
2 03444 1 Hex Arm Center 12'-24'
00297 2 Hex Arm w/o support 30'
3 03445 1 Hex Arm Left 12'-24'
01436 1 Hex Arm w/ 2 support 30'
4 00088 1 Main Support Front
5 00091 1 Main Support Rear
6 03616 2 Dolly Assy 3 9/16" 12'-24'
01537 2 Dolly Assy 5" 30'
7 03615 2 Dolly Assy 2 5/16" 12'-24'
03616 2 Dolly Assy 3 9/16" 30'
8 02645 4 Dolly Scraper
9 02923 4 Dolly Wheel 2 ¼
10 00281 3 Ring Section
11 00094 2 Support Frame Tab
12 B616 HC5P 4 Bolt ½ x 3 ½ Unc
13 N6HCCP 4 Nut ½ CL
14 B608CC5P 9 Bolt ½ x 1 ¼ Crg
16 W6LP 9 Washer ½ Lock
17 N6HCP 9 Nut ½ Hex
19 B619HC5P 3 Bolt ½ x 4
20 P411K 4 Dolly Pin
21 P007B 4 Cotter Pin
22 03612 4 Dolly Roller
23 N9HJFP 4 Nut ¾ Hex Jam
24 03617 2 Dolly Wldmt 2 5/16" 12'-24'
03618 2 Dolly Wldmt 3 9/16" 12'-24'
01744 2 Dolly Wldmt 5" 30'
25 02889 4 Dolly Wheel Spacer
26 W6FP 8 Washer 1/2 Flat
27 N6HCCP 4 Nut ½ Cl
28 03613 1 Roller Pin
P.T. TRI-CABLE PART #'S
PART NO# DESCRIPTION
02296 Tri-Cable Assy 12' (82")
02297 Tri-Cable Assy 14' - 16' (91")
02298 Tri-Cable Assy 18' (99")
02299 Tri-Cable Assy 20' (108")
02300 Tri-Cable Assy 24' (130")
02301 Tri-Cable Assy 30' (166")
Posi-Trac; Revised 2008-11-05 42
POSI-TRAC DRIVE UNIT
8 25 26 21
30
25 26 27
32 31
27 7 6
20 4 5
35
29
3 26 27 28
2 22
24
KEY PART NO# REQ'D DESCRIPTION
1 03096 1 Drive Unit Assy
2 03128 1 Drive Unit Brace Tube
3 03561 1 Drive Unit Mtg Wldmt
4 60-50B12-1.25 1 Sprocket #50b12 x 1 ¼ Inch
5 03557 1 Drive Unit Spacer Plate
6 03562 1 Chain Tightener Tab
7 03558 1 Drive Unit Adjuster Angle
8 03572 1 Chain Guard Cover
9 00506 1 Sprocket, Drive (50 B 30)
10 00516 2 Bearing Pillow Block 1 In. w/Coll
11 K213S 2 Key ¼ sq x 2 ½
12 K219S 2 Key ¼ x 4 Sq
13 P108G 2 Roll Pin 3/16 x 1 ¼
14 03120 1 Drive Shaft
15 00701 1 Clutch Shaft With Plate
16 00512 2 Clutch Half
17 00700 1 Drive Wheel Machined
KEY PART NO# REQ'D DESCRIPTION
18 00514 1 Spring, Clutch Oil Tempered
19 00515 1 Nut Adjusting 1 7/8 - 12 Trd
20 03564 1 #50 Roller Chain 44 Pins
21 00446 1 Main Belt Guard Bracket
22 03616 1 Dolly Assembly 3 9/16" 12'-24'
01537 1 Dolly Assembly 5" 30'
23 02010 1 NRB 1 7/8 14 Ga
24 B418HX5P 1 Bolt 3/8 x 3 ¾
25 W4FP 1 Washer Flat 3/8
26 W4LP 1 Washer Lock 3/8
27 N4HCP 1 Nut 3/8
28 B407HC5P 1 Bolt 3/8 x 1
29 B412HC5P 1 Bolt 3/8 x 2 ¼
30 B615HC5P 2 Bolt ½ x 3
31 N6HCP 2 Nut ½
32 W6LP 2 Washer Lock ½
33 03792 1 NRB 1 7/8 10 Ga
34 P2RPG 1 Roll Pin ¼ x 1 3/8
35 02837 AR Drive Unit Shim
36 00965 1 Clutch Assembly
Posi-Trac; Revised 2008-11-05 43
AUGER TRANSMISSION #07000
KEY PART # REQ'D DESCRIPTION
1 07000 1 Transmission Complete
2 07001 4 Oil seal, bouble lips
3 07051 8 Tapered roller bearing 30207
5 07052 1 Output shaft spacer
6 07007 1 Worm gear LH 30 teeth
7 07010 1 Output shaft
8 07053 3 Key, A type
9 K207S 1 Key, ¼" x ¼" x 1"
10 07054 AR Bearing shim 0.1 mm (72 mm)
AR Bearing shim 0.3 mm (72 mm)
13 07056 2 Cover with hole (72 mm)
15 07057 1 Cover (72 mm)
17 07003 1 RH & LH Worm
18 K207S 1 Key, ¼" x ¼" x 1 ½"
PT; Revised 2007-10-12 44
KEY PART # REQ'D DESCRIPTION
19 00643 1 Cover plate
20 07064 8 Screw, Hex. head, M8 x 16 lg
22 00673 1 Trans. Dipstick 3/8 NPT
23 07058 28 Washer, Lock, Helical spring 8 mm
24 M203B 1 Drain plug
26 07005 1 Shaft include worm LH
27 07006 1 Worm gear 24 teeth
28 07059 2 Cover (115 mm)
29 07060 20 Screw, Hex. head, M8 x 20 lg
35 07008 1 Worm gear 24 teeth
36 07011 1 Output shaft
N/I 03270 1 RTV Sealant
SIDERAILS, KICK GUARD & COVERS
TT, PT; Revised 2008-11-05 45
SIDERAILS, KICK GUARD & COVERS
KEY PART NO# REQ'D DESCRIPTION
1 00226 1 RH Rear Side Rail for 12'-20' (78) 00227 1 RH Rear Side Rail for 24' (90) 00228 1 RH Rear Side Rail for 30' (126)
2 00229 1 LH Rear Side rail for 12'-20' (78) 00230 1 LH Rear Side rail for 24' (90) 00231 1 LH Rear Side rail for 30' (126)
3 B407HC5P AR Bolt 3/8 x 1 4 W4LP AR Washer 3/8 Lock 5 N4HCP AR Nut 3/8 Hx 6 00232 1 Lh Front Side Rail for 12'-16' (63)
00233 1 Lh Front Side Rail for 18'-20' (87) 00234 1 Lh Front Side Rail for 24'-30' (99)
7 00238 1 RH Front Side Rail for 12'-16' (63) 00239 1 RH Front Side Rail for 18'-20' (87) 00240 1 RH Front Side Rail for 24'-30' (99)
8 B307HC5P AR Bolt 5/16 x 1 9 W3LP AR Washer 5/16 Lock 10 N3HCP AR Nut 5/16 Hx 11 00205 1 Kickguard Assy for 12' (63)
00206 1 Kickguard Assy for 14' (75) 00207 1 Kickguard Assy for 16' (87) 00208 1 Kickguard Assy for 18' (99) 00209 1 Kickguard Assy for 20' (111) 00211 1 Kickguard Assy for 24' (135) 00214 1 Kickguard Assy for 30' (171)
12 00946 1 Med. Back Auger Shield SS 12'-16' & 30' (63) 00947 1 Long Back Auger Shield SS 18'-30' (87)
13 00945 1 Short Back Auger Shield SS 12'-20' & 30' (49 ½ ) 2 Short Back Auger Shield SS 24' (49 ½ )
21 02934 1 Center Grille Cover Support for 18', 20' & 30' 22 03489 1 Grille Cover Wldmt 12' RH (36 5/16)
03490 1 Grille Cover Wldmt 12' LH (36 5/16) 03491 1 Grille Cover Wldmt 14' RH (48 5/16) 03492 1 Grille Cover Wldmt 14' LH (48 5/16) 03493 1 Grille Cover Wldmt 16' RH (60 5/16) 03494 1 Grille Cover Wldmt 16' LH (60 5/16) 03495 1 Grille Cover Wldmt 18' RH (72 5/16) 03496 1 Grille Cover Wldmt 18' LH (72 5/16) 03497 1 Grille Cover Wldmt 20' RH (84 5/16) 03498 1 Grille Cover Wldmt 20' LH (84 5/16) 03487 1 Grille Cover Wldmt 24'-30' RH (54" Angle) 03488 1 Grille Cover Wldmt 24'-30' LH (54" Angle)
23 03338 1 Galvanized Blankout (24" Blower) 01517 1 Galvanized Blankout (28" Blower)
24 01534 1 Chain & S-Hook assembly (Twin Trac) 25 00445 1 Lower Belt Shield Bracket 26 00447 1 Lower Belt Shield (24" Blower)
00914 1 Lower Belt Shield (28" Blower) 27 00187 1 Back Blower Shield (Galv) 28 00915 1 Side Blower Shield (24" Blower Twin Trac))
03579 1 Side Blower Shield (28" Blower Twin Trac) 03139 1 Side Blower Shield (24" Blower Posi Trac) 03580 1 Side Blower Shield (28" Blower Posi Trac)
30 00189 1 Knuckle Shield (Twin Trac) 31 01646 1 Push Pipe Bracket (Twin Trac) 33 03233 1 24'-30' Section Grille Support 34 03491 1 Grille Cover Wldmt 24' RH (48 5/16)
03492 1 Grille Cover Wldmt 24' LH (48 5/16) 03497 1 Grille Cover Wldmt 30' RH (84 5/16) 03498 1 Grille Cover Wldmt 30' LH (84 5/16)
TT, PT; Revised 2008-11-05 46
AUGERS & IDLER FRAME ASSEMBLY
TT, PT, Rad; Revised 2008-11-05 47
AUGERS & ILDER FRAME ASSEMBLY
KEY PART NO# REQ'D DESCRIPTION
1 00670 1 Trans Mtg angle Front 12'-24' 01289 1 Trans Mtg angle Front 30'
2 B609HC5P 3 Bolt ½ x 1 ½ 3 W6LP 4 Washer ½ / Lock 4 N6HCP 4 Nut ½ 5 B608HC5P 1 Bolt ½ x 1 ¼ 6 00671 1 Transmission Tab 7 00997 1 Rear Trans. Mtg Brkt 11 07100 1 Transmission, Twin Trac, Radial
07000 1 Transmission, Posi Trac 12 B715HF5B 4 Bolt Shoulder 9/16 x 3 13 N7HTF8P 4 Nut 9/16 Lock Unf 14 00935 2 Wall Wheel 1" - 1.032 Bore 15 01314 2 Wall Wheel Bolt Ass'y (including item 16,17,18,23)
00168 2 Wall Wheel Bushing 16 N9HCP 2 Nut ¾ 17 W9LP 2 Washer ¾ Lock 18 W9FP 4 Washer ¾ Flat 19 40-222624 2 Oilite Bearing SO 1.625 x 1.375 x 1.5 20 00961 2 Bearing Hanger 21 P1.509B 2 Cotter Pin 7/32 22 00934 1 Idler End Frame Assembly (including item 24)
00158 1 Idler End Frame Wldmt 23 B919SC2P 2 Bolt ¾ x 4 24 00162 2 Bearing Bracket (Hanger Plate) (included with item 22) 25 00150 1 Wall Chippers (Rh Thread) 26 00146 1 Wall Chippers (Lh Thread) 27 00155 1 Stub Shaft (Rh Thread) 28 00154 1 Stub Shaft (Lh Thread) 29 00765 1 Tooth Lh Starter 30 00144 AR Teeth Auger Lh
00960 AR Auger Teeth Kit HD Lh 31 00095 1 Heavy Duty Front Auger Assy for 12' (79 ¼")
00096 1 Heavy Duty Front Auger Assy for 14' (91 ¼") 00097 1 Heavy Duty Front Auger Assy for 16' (103 ¼") 00098 1 Heavy Duty Front Auger Assy for 18' (115 ¼") 00099 1 Heavy Duty Front Auger Assy for 20' (127 ¼") 00101 1 Heavy Duty Front Auger Assy for 24' (151 ¼") 00104 1 Heavy Duty Front Auger Assy for 30' (187 ¼")
32 00766 1 Tooth Rh Starter 33 00145 AR Teeth Auger Rh
00959 AR Auger Teeth Kit HD Rh 34 00120 1 Heavy Duty Back Auger Assy for 12' (75 5/8")
00121 1 Heavy Duty Back Auger Assy for 14' (87 5/8") 00122 1 Heavy Duty Back Auger Assy for 16' (99 5/8") 00123 1 Heavy Duty Back Auger Assy for 18' (111 5/8") 00124 1 Heavy Duty Back Auger Assy for 20' (123 5/8") 00126 1 Heavy Duty Back Auger Assy for 24' (147 5/8") 00129 1 Heavy Duty Back Auger Assy for 30' (183 5/8")
35 B407HC5P 4 Bolt 3/8 x 1 36 W4LP 4 Washer 3/8 37 N4HCP 4 Nut 3/8 38 B305CC2B AR Bolt 5/16 x ¾ Crg Std Knives 40 N3HJCB AR Jam Nut 5/16 Black Std Knives 52 03301 2 Plastic Spacer 53 03394 2 Reinforcing Plate
TT, PT, Rad; Revised 2008-11-05 48
19
COUNTER WEIGHTS, RAILS & BACK CROSS MEMBER
9 5 2 22
9 10
1 10
8 30
7 15 18
33 31
32 26
8
26
24
5 4
9 2
25
11 12
10
16
17
11 14 27
13 29 28
6
10
27
9 34
3
KEY PART NO# REQ'D DESCRIPTION
1 02895 1 Rear Tension Wheel Wldmt 12' (43")
02703 1 Rear Tension wheel Tube 14'-30' (55")
2 01550 2 Wall Wheel
3 02687 1 Guide Wheel Tube 12' (46")
02688 1 Guide Wheel Tube 14'-18' (68")
02689 1 Guide Wheel Tube 20' (92")
02690 1 Guide Wheel Tube 24' (120")
50056 1 Guide Wheel Tube 30' (156")
4 02897 1 Wall Wheel Wldmt 12' (33")
02731 1 Wall Wheel Wldmt 3' (14'-16')
02732 1 Wall Wheel Wldmt 4' (18'-30')
5 N8HCCP 2 Locknut 5/8
6 00201 1 Back Crossmember, Wldmt
7 02708 1 Rear Tension Wheel Brkt Wldmt
8 02735 2 Counter-Weight Angle 12' (32")
02736 2 Counter-Weight Angle 14' (36")
02737 2 Counter-Weight Angle 16' (48")
02738 2 Counter-Weight Angle 18' (60")
02739 2 Counter-Weight Angle 20' (72")
02741 2 Counter-Weight Angle 24' (96")
00772 2 Counter-Weight Angle 30' (132")
9 W8FP 4 Washer 5/8 Flat
10 B407HC5P 17 Bolt 3/8 x 1
11 W4LP 23 Washer 3/8 Lock
12 N4HCCP 19 Nut 3/8 Lock
Posi-Trac; Revised 2008-04-10
KEY PART NO# REQ'D DESCRIPTION
13 B407HF8P 4 Bolt 3/8 x 1 UNF
14 N4HCFP 4 Nut 3/8 UNF
15 99-429 1 1/8 Hairpin
16 N9HCP 4 Nut 3/4
17 W9LP 2 Washer ¾ Lock
18 B609HC5P 4 Bolt ½ x 1 ½ Gr.5
19 B408HC5P 2 Bolt 3/8 x 1 ¼ Gr.5
22 03800 1 Connector Pin
24 00835 1 Counter-Weight Brace Angle RH (24')
01160 1 Counter-Weight Brace Angle RH (30')
25 00770 1 Counter-Weight Brace Angle LH (24')
01159 1 Counter-Weight Brace Angle LH (30')
26 01151 2 Counter-Weight X-Brace (30')
27 01740 2 Top support wldmt (30')
28 02412 2 Support strap tighten bracket (30')
29 02413 2 Support strap tighten rod (30')
30 00278 2 C-Iron Counter-Weight Assy 12'-14'
3 C-Iron Counter-Weight Assy 16'
4 C-Iron Counter-Weight Assy 18'-20'
6 C-Iron Counter-Weight Assy 24'
9 C-Iron Counter-Weight Assy 30'
VS-3129 2x Adjusting Handle
31 00487 1 Tension Arm Chain
32 00488 1 Spring, Tension Arm
33 03784 1 Chain Tightener Handle
34 VS-3129 1 Adjusting Handle
49
Part no.: 01782