PT. L INCOLN ELECTRIC INDONESIA MILD STEEL ELECTRODE
Jetweld LH-70
Jetweld® LH-70 is a semi iron powder electrode that gives highest deposition rates consistent with good out of position welding capability . Goodcharpy and CTOD values.
Where x-ray quality and excellent mechanical properties arerequired.
Thick sections and restrained joints in mild and low alloy steelswhere shrinkage stresses tend to cause weld cracking.
To reduce pre-heat requirements.
To resist cracking in medium to high carbon and hard to weld steels.
To resist hot shortness in sulphur and phosphorus bearing steels.
To reduce porosity in sulphur bearing steels
Vertical and overhead welding.
The product comes standard in a hermetically sealed can whichallows for immediate use from the can and for up to 9 hours beforere-baking is required.
KEY FEATURES
C.ID.JWLH70 08/15 © PT. Lincoln Electric Indonesia. All Rights Reserved.
APPLICATIONS
AWS E7018 H4R
Oil refinery vessels and piping
Hydroelectric penstocks
Oil and water storage tanks
High pressure piping
Mining and earthmovingequipment
Closing seams and nozzles onpressure vessels
Heavy duty machinery
Ship construction
Offshore oil and gas platformsand modules
®
DC+, AC (if OCV>75 volts)
POLARITY APPROVALS
ABS: 3YH5 LR: 3YH5
DIFFUSIBLE HYDROGEN
Jetweld® LH-70
Typical Results (ml/100g weld deposit)
3
PT. L INCOLN ELECTRIC INDONESIA
C U S T O M E R A S S I S T A N C E P O L I C Y
The business of The Lincoln Electric Company® is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for information or advice about their use of our products. Our employees respond to inquiriesto the best of their ability based on information provided to them by the customers and the knowledge they may have concerning the application. Our employees, however, are not in a position to verify the information provided or to evaluate the engineering requirements for the particular weldment. Accordingly, Lincoln Electric does not warrant or guarantee or assume anyliability with respect to such information or advice. Moreover, the provision of such information or advice does not create, expand, or alter any warranty on our products. Any express or implied warranty that might arise from the information or advice, including any implied warranty of merchantability or any warranty of fitness for any customers’ particular purpose is specifically disclaimed.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.
PT. LINCOLN ELECTRIC INDONESIAJl Inti Raya Blok C10/12A, Bekasi International Industrial Estate - 177550, Lippo Cikarang, West Java, Indonesia
Phone: +62 21 8990 8488 / 8334 • Fax: +62 21 8990 7630 • www.lincolnelectric.com
T E S T R E S U L T STest results for mechanical properties, deposit or electrode composition and diffusible hydrogen levels were obtained from a weld produced and tested according to prescribed standards,and should not be assumed to be the expected results in a particular application or weldment. Actual results will vary depending on many factors, including, but not limited to, weld procedure, plate chemistry and temperature, weldment design and fabrication methods. Users are cautioned to confirm by qualification testing, or other appropriate means, the suitabilityof any welding consumable and procedure before use in the intended application.
DIAMETERS / PACKAGING
Diameter (mm)
2.53.24.05.0
Length (mm) Product Number (Cans) Product Number (Hermiseal Packets)
350350350350
IELH751S23IELH751S33IELH751S43IELH751S54
IELH751H23IELH751H33IELH751H43IELH751H54
TYPICAL CHEMICAL COMPOSITION, ALL WELD METAL
%Mn %Si %Cr %Ni %Mo %V %P %S%C
Requirements AWS A5.1 E7018 H4R
Typical Values 1.010
1.60 max
0.051
0.15
<0.005
0.20 max
0.341
0.75 max
0.003
0.30 max
0.040
0.30 max
0.013
0.035
0.002
0.08 max
0.012
0.035
TYPICAL WELDING PARAMETERS
Diameter (mm)
2.53.24.05.0
Current (Amps) Range DC+ Current (Amps) Range AC
70 - 10090 - 150120 - 190180 - 280
80 - 120110 - 170135 - 225200 - 300
MECHANICAL PROPERTIES, ALL WELD METAL
Tensile Strength(MPa)
Yield Strength(MPa)
Elongation(%)
Impact ISO -V(j)-30°C
Requirements AWS A5.1 E7018 H4R
Typical Values 427
400 min
510
490 min
28
22 min
201
27 min