7/28/2019 Recon Figt
1/44
KING SAUD UNIVERSITY
COLLEGE OF ENGINEERING
RESEARCH CENTER
Final Research Report No. 425/4
Electronically tuned antenna for third generation mobile
communication
By
Dr. Abdel Fattah Sheta
RabiII 1426 H
May 2005G
7/28/2019 Recon Figt
2/44
Table of Contents
Page
Acknowledgment 3
List of Figures 4Abstract (English) 5
Abstract (Arabic) 6
Chapter 1: Compact Microstrip Antennas: Characteristics and Limitations 7
1.1 Introduction 7
1.2 Challenges and Fundamental Limitations 8
1.3 Tuning Concept Solution 10
Chapter 2: Active Devices Used in RF Tuning
122.1 Introduction 12
2.2 Characteristics of Varactor Diodes 12
2.3 Characteristics of PIN Diodes 16
Chapter 3: Tunable Antenna Techniques and Mobile Phone RF SystemArchitecture
20
3.1 Introduction 20
3.2 Varactor Based Tunable Microstrip Antennas 21
3.3 Switching Based Tunable Microstrip Antennas 233.4 The proposed RF System Architecture 25
Chapter 4: Dual Band Tunable Antenna For Cellular Phone 27
4.1 Introduction 27
4.2 Effect of Varactor Diodes in Microstrip Circuits 28
4.3 Compact Tunable Microstrip Antenna 31
4.4 Experimental Results 39
Chapter 5: Conclusions and Recommendation 41
References 43
2
7/28/2019 Recon Figt
3/44
Acknowledgment
The authors would like to acknowledge the assistance and the financial support provided
by the Research Center in the College of Engineering at King Saud University for this
project under grant number 4/425.
3
7/28/2019 Recon Figt
4/44
LIST OF FIGURES
Page
Figure 1.1 Antenna within a sphere of radius r. 9
Figure 1.2 Fundamental limit of Q versus antenna size kr < 1 , k = 2/ = /c. 9
Figure 2.1 Varactor characteristics. 18Figure 2.2 Varactor diode equivalent circuit. 18
Figure 2.3 Physical structure of a PIN diode. 18
Figure 2.4 PIN diode equivalent circuit. 19
Figure 2.5 I-V characteristics of a PIN diode. 19
Figure 3.1 Electronic tuning of half-wavelength microstrip antenna. 22
Figure 3.2 Electronic tuning of quarter-wavelength shorted microstrip antenna. 22
Figure 3.3 Diode tunable PIFA. 22
Figure 3.4 Frequency tuning by switching techniques. 24
Figure 3.5 The conventional dual-band full duplex RF front end. 26
Figure 3.6 The proposed dual-band full-duplex RF front end based on a tunable antenna
pair.
26
Figure 4.1 Capacitance-Voltage relation of SMTD3001. 29
Figure 4.2 Electrical length equivalence of a varactor located at the end of the line. 29
Figure 4.3 The variation of effective electrical length of the varactor diode SMTD3001
against microstrip line width on Duroid substrate with r = 2.2 and 1.57 mmthickness.
30
Figure 4.4 L and inverted L shape antenna. 32
Figure 4.5 The proposed dual-band tunable microstrip antenna. 32
Figure 4.6 1 versus (2 + eff) for different values of K. 35
Figure 4.7 Layout of the dual-band tunable antenna designed for GSM applications. 35
Figure 4.8 Simulation results (S11) of the dual band proposed antenna at the lower
frequency band (GSM-900 MHz) for various values of reverse bias voltage
VR.
36
Figure 4.9 Simulation results (S11) of the dual band proposed antenna at the higherfrequency band (DCS-1800 MHz) for various values of reverse bias voltage
VR.
36
Figure 4.10 Resonance frequencies of the dual band proposed antenna against reverse biasvoltage VR.37
Figure 4.11 Far field simulated radiation patterns at different bias conditions. 38
Figure 4.12 Measured return loss of the tunable antenna for reveres bias of 0, 1, and 3 V. 40
Figure 4.13 Measured return loss of the tunable antenna for reveres bias of 0, 1, and 3 V
for a modified lower band element.
40
4
7/28/2019 Recon Figt
5/44
ABSTRACT
Small size antennas usually suffer from bandwidth limitations. Bandwidth can be
increased by adding lossy elements but, they significantly affect the efficiency of the
antenna. One method to solve the efficiency problem without increasing the antenna size
is to use the tunable antenna concept. Recently, tunable antennas attract much attention
in mobile communications. The objective of this project is to develop compact dual-band
electronically tunable microstrip antennas for operation in GSM/DCS-1800 system.
Tunable antenna, is a small size antenna that would not cover all bands simultaneously,
but provides narrower instantaneous bandwidths that are dynamically selectable at higher
efficiency than conventional antennas. Bandwidth selection can be achieved by
electronically change the reactive loading of the resonator by means of PIN diode or
varactor diode. The main characteristics of the PIN and varactor diodes that are useful
for tunable microstrip antenna design are described. The loading effect of varactor diode
on microstrip circuits is investigated and design curves that relate the biasing voltage to
the effective electrical line length for different line widths are presented. The analysis of
a compact dual-band microstrip antenna suitable for this application is, then, described.
A dual-band antenna is designed and implemented to operate at the GSM/DCS-1800
bands when connected to the varactor diode SMTD3100. The design and
implementation is carried out on Duroid dielectric substrate with r = 2.2 and thickness
1.57 mm. The simulations are performed using IE3D simulator. Simulation results show
that the required bandwidth can be easily covered with voltage changes from 0 V to 3 V,
which is suitable for mobile hand phones. Frequency shift between simulations andmeasurements due to the limited accuracy of the varactor diode capacitance is observed.
This frequency shift is compensated by adding a small piece of copper foil on the element
that resonates at the lower band. However, the circuit layout is difficult to support such
modification at the higher band. Computed radiation patterns show consistency for
different bias conditions and show omni-directional shape.
5
7/28/2019 Recon Figt
6/44
. .
.
.
GSM/DCS-1800
.
.
PIN
.
.
.
GSM/DCS-1800
SMTD31002.2
1.57. IE3D
0 3 .
.
.
.
.
.
.
6
7/28/2019 Recon Figt
7/44
CHAPTER 1
COMPACT MICROSTRIP ANTENNAS: CHARACTERISTICS AND
LIMITATIONS
1.1 INTRODUCTIONMicrostrip antennas (MSAs) in general have a conducting patch printed on a grounded
dielectric substrate (usually r 10). MSAs have some attractive features such as, low
profile, light weight, easy fabrication, and conformability to mounting hosts. However,
MSAs inherently have narrow bandwidth characteristics. The patch conductors, normally
of copper or gold, can assume virtually any shape, but regular shapes such as rectangular,
square, circular, elliptical, triangular, and annular ring, are generally used to simplify
analysis and performance prediction. Ideally, the dielectric constant, rof the substrate
should be low (r < 2.5), to enhance the fringe fields that account for the radiation.
However, other performance requirements may dictate the use of substrate materials
whose dielectric constants can be greater than, say, four.
In general, MSAs are half-wavelength structures. At the lower microwave frequency,
especially below 2 GHz, the size of conventional MSAs, becomes too large to be
integrated in mobile handset. However, with some modifications, any of the basic
microstrip structures can be optimized for:
7
7/28/2019 Recon Figt
8/44
(1) Implementation in a very small area at the expense of bandwidth.
(2) Reasonable small area with acceptable bandwidth, for mobile applications.
(3) Large area with associated wide bandwidth
The possibility to employ antennas that fit in smaller volumes, but still have an efficient
behavior is certainly a challenge. The challenges and fundamental limitations for
designing small antennas will be discussed in the next section.
1.2 CHALLENGES AND FUNDAMENTAL LIMITATIONS
The term electrical small antenna has become understood to include any antenna which
fits inside a sphere of radius r 1/k, as shown in Fig. 1.1, where k is the wave number
associated with the electromagnetic field. It has been noted that as the antenna size
decreases the bandwidth decreases. The bandwidth is derived from the quality factor (Q)
by assuming that the antenna equivalent is a resonant circuit with fixed values. The
fractional bandwidth is defined as the normalized spread between the half-power
frequencies as:
Q
1
f
ff(BW)Bandwidth
center
lowerupper=
= (1.1)
If the antenna is lossy, a series resistance will be added to the radiation resistance that
results in a significant decrease of Q and so increase in bandwidth. The Q-size relation is
illustrated in Fig. 1.2 for various efficiencies [1]. These curves represent the minimum
values of Q (or the highest bandwidth) that can be obtained from an antenna whose
8
7/28/2019 Recon Figt
9/44
structure can be enclosed within a sphere of radius r and whose radiated field outside the
sphere can be represented by a single spherical wave mode.
r
Fig. 1.1 Antenna within a sphere of radius r.
Fig. 1.2 Fundamental limit of Q versus antenna size kr < 1 , k = 2/ = /c [1].
0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5
100
80
40
20
10
8
4
2 = 100%10%
5%
r
Antenna within a
sphere of radius r
radiation efficiencyQualityfactorQ
50%
kr
9
7/28/2019 Recon Figt
10/44
In conclusion, according to the theory developed in [1]-[3], there exists a fundamental
law that restricts the performance of the antennas enclosed in a given volume. The law
states that the Q of any linearly polarized antenna cannot be smaller than what is
obtained, as shown in Fig. 1.2, if only the lowest spherical mode is allowed to act outside
the smallest sphere that encloses the antenna. Thus, in order to approach the theoretical
limit, the antenna structure should utilize as efficiently as possible the enclosing sphere.
To do so, various wide band microstrip structures have been developed by increasing the
substrate thickness, while compactness has been achieved by decreasing the surface.
Planar inverted F antennas (PIFAs) are the most important structures developed for this
purpose. Various PIFAs have been proposed for single, dual, and triple band [4]-[12].
More size reduction is possible, if a tunable frequency band operation can be obtained
from the antenna structure instead of single wide band operation.
1.3 TUNING CONCEPT SOLUTION
The narrow bandwidth of conventional microstrip antennas has many restrictions in real-
time applications. The tunable antenna concept offers solutions to this problem. Recently,
tunable antennas attract much attention for their applications in wireless communications,
electronic surveillance, and countermeasures by adapting their properties to achieve
selectivity in frequency, bandwidth, polarization and gain.
10
7/28/2019 Recon Figt
11/44
Microstrip antenna is a resonant element, and so its resonance frequency can be
determined by its lumped element equivalence. Therefore, any reactive loading of the
patch leads to a change in its resonance frequency. Such loading can be performed either
mechanically or electronically. Shorting pins or posts [13], stubs [14], variable dielectric
layer thickness [15], varactor diodes [16][19], switching diodes [20]- [23], and optical
control have been used to tune microstrip antennas. Pins, posts, stubs, and variable
dielectric layer thickness give rise to mechanical tuning. Whereas varactor and switching
diodes embedded in the patch and optical control of PIN diode impedance can be used for
electronic tuning of the patch antenna.
The study of dual-band electronically tunable microstrip antenna is the subject of this
project. Varactor and PIN diodes are the main electronically frequency control
components that are used for such applications. The basic theory and principle of
operation of these devices are presented in the next chapter. In chapter three, the studies
of the main microstrip antennas structures that can use electronic tuning are covered. The
design and implementation of a new dual-band structure which is more suitable for low
cost applications is discussed in chapter four. Concluding remarks and future prospective
are introduced in chapter five.
11
7/28/2019 Recon Figt
12/44
CHAPTER 2
ACTIVE DEVICES USED IN RF TUNING
2.1 INTRODUCTION
Electronic tuning of microstrip antennas is either achieved by the mean of Varactor
diodes and/or PIN diodes. These devices are suitable for applications in microwave
frequencies. Varactors are useful for many RF applications including: frequency tuning
for active and passive circuits, frequency multiplication, frequency conversion, harmonic
generation and parametric amplification. PIN diode is the most important device for
signal control at the microwave range. Signal amplitude and phase can be easily
electronically controlled using PIN diode. In this chapter we will study the main
characteristics of both devices at the frequency of interest (< 2 GHz). The next section
will elaborate the characteristics of varactor diodes and section three is devoted to the
characteristics and the principle of PIN diodes for switching.
2.2 CHARACTERISTICS OF VARACTOR DIODES [24]
The varactor diode is one of the old microwave solid-state-devices. It is also called a
parametric diode. The varactor diode is a nonlinear device and provides voltage-
dependent variable capacitance. Varactors are generally semiconductor p-n junctions,
Schottky-barrier junctions, or point contact diodes made from gallium arsenide or silicon.
12
7/28/2019 Recon Figt
13/44
Most varactors are fabricated on n-type semiconductors with p-type diffusion to form
junctions.
The operation of a varactor diode is based on the reverse-biased pn junction. An increase
in the reverse bias widens the depletion region between the p- and n-type substrates, and
the junction capacitance is reduced. The junction capacitance Cj for a reverse-biased pn
junction as a function of the applied reverse dc voltage V is given by
M
bi
joj )
V(1C(V)C = (2.1)
where Cj0 is the junction capacitance at zero bias, bi the contact potential (0.7V for
silicon and 1.3V for GaAs) andMis a coefficient which depends on the junction doping
profile. Both Cj0 and Mare dependent on the doping characteristics of the pn junction.
For the abrupt type varactorM=0.5, but in hyperabrupt type varactorMvaries with the
applied reverse bias between 0.5 and 5. If the range of the applied bias is sufficiently
narrow, the voltage dependency ofMmay be ignored, and it may be replaced by an
average value over that range.
Equation (2.1) is plotted in Fig. 2.1 for an abrupt pn junction (M = 0.5). The equivalent
circuit of this device in its package form is shown in Fig. 2.2. It is modeled by a voltage
dependent junction capacitance Cj (V) and the series resistance R S(V), associated with
the ohmic contact and the finite thickness of the epitaxial layer. Since the depletion
region expands as the bias is increased, the undepleted region becomes smaller which
decreases the resistance of the structure. The series resistance should be as low as
possible in order to keep the losses associated with the diode low. As the operation is
13
7/28/2019 Recon Figt
14/44
based on the reverse-biased pn-junction, it can be assumed that the junction resistance
will be very large and may therefore be ignored. In commercial products, the diode is
usually installed in a package. Due to the package material, the geometry and the bonding
wires, the package always has some kind of package inductance Lp and package
capacitance Cp, that have an influence on the performance of the diode. Lp and Cp are
assumed to be constant with the bias voltage. The disadvantage of this model is that it
fails to take into account the non-linearities of the junction. The parameters for this
circuit have to be taken straight from the manufacturers datasheet curves. Usually, the
effect of the package capacitance, Cp on the characteristics of the diode is negligible and
can be ignored and then the impedance of the varactor Zd can be written as
))(
1()(),(
VCLjVRVZ
j
psd
+= (2.2)
Since the operation of a varactor diode is based on the reverse-biased pn junction, the
operation frequency range should be below a particular frequency which is called cutoff
frequency fcoff and determined by the diode series resistance Rs(V) and the junction
capacitance Cj (V) as
)()(2
1)(
VCVRVf
js
cutoff
= (2.3)
Since both Rs and Cj decrease as a function of the increased reverse bias, the cut-off
frequency is usually defined according to the zero bias values of these parameters
14
7/28/2019 Recon Figt
15/44
In order to keep the diode impedance, constantly, in the capacitive operating mode, the
series resonance frequency of the diode should, in all circumstances, remain clearly
above the operating frequency range. In the series resonance condition, the reactive part
of the impedance equals zero, and the resonant frequency can be solved from Equation
(2.3) and written as
)(2
1
VCLf
jp
r
= (2.4)
Since the junction capacitance decreases as a function of the applied reverse bias, the
criterion for the capacitive operating mode is met, provided that thefrexceeds the highest
operating frequency at the zero bias level.
In low-loss designs such as antenna applications, fcutoff is usually much higher than the
series resonance frequencyfrof the packed diode (> 10 fr ). This means that in case the
series resonance frequency requirement is fulfilled, the cut-off frequency requirement is
also fulfilled. It must be emphasized that the cut-off frequency mainly defines the energy
dissipation of the varactor, while thefr defines the frequency above which the operation
of the varactor becomes inductive due to the effect of the package inductance.
In mobile phone applications the temperature of the environment can vary within a rather
large range. This can have a significant effect on the properties of the varactor-based
tuning circuit, because the capacitance of the diode tends to increase as the temperature
increases. The capacitance of a hyperabrupt diode is more sensitive to temperature in
comparison to the abrupt diode.
15
7/28/2019 Recon Figt
16/44
2.3 CHARACTERISTICS OF PIN DIODES [24]
The p-in diode has its name because of its doping semiconductor profile which consists
of a lightly doped intrinsic region sandwiched between two doped p and n regions. The
semiconductor material is usually silicon, but gallium arsenide can be also used. PIN
diodes are used as switches or attenuators for signals at microwave frequencies. The
sketch of a PIN diode is shown in Fig. 2.3.
The PIN diode is similar to the PN diode but with smaller junction capacitance. Since the
width of the depletion zone is inversely proportional to the resistivity (or doping
concentration) of the p or n region (whichever has the lower impurity doping
concentration, the depletion region of PIN is wider than that in a PN diode. The wider
depletion region corresponds to smaller junction capacitance. The effect is very useful
for a diode used as a microwave switch. This is because the impedance of the diode
under reverse bias gets higher as the capacitance gets lower and the device becomes more
effective as an open circuit. Because of the heavy doping of the P+
or N+
regions, the
depletion does not extend far into them, and the depletion width is essentially equal to the
I region width. The junction capacitance in the reverse bias is determined by this width.
The most important property of the PIN diode is that it can, under certain circumstances,
behave as an almost pure resistance at high frequencies. The value of the resistance is
dependent on the resistivity of the intrinsic region and the applied bias current. The
intrinsic region has a high resistance R0 at zero bias. In forward bias, the junction
resistance depends on the conductivity of the I layer. An increase in the applied forward
16
7/28/2019 Recon Figt
17/44
bias increases the injection of carriers from the P+ and N+ regions. This phenomenon
reduces the specific resistance to a level below the one obtained from doping alone, thus
inducing a lower junction resistance. Together with N+
and P+
regions, the I region, forms
a junction capacitance Cj.
The equivalent circuit can be represented as shown in Fig. 2.4. The arrow is connected to
Rj in the forward bias and Cj in the reverse bias. Cj(V) and Rj(V) will depend on the
applied bias as shown in the I-V curve of Fig. 2.5.
The circuit parameters at forward and reverse bias are given as:
Forward bias: the circuit parameters can approximately take the values:
Cj(V) = 1 pF
Rj(V) = 0.5
Zc = -j160 at 1 GHz
The circuit is almost a short circuit.
Reverse bias:
The circuit parameters can be approximated as:
Cj(V) = 0.2 pF
Rj(V) = 20 K
Zc = -j 800 at 1 GHz
Zc is much greater tha 50 and acts as good open circuit
17
7/28/2019 Recon Figt
18/44
Fig. 2.1 Varactor characteristics.
VbiVB
Cjo
Cj(V)
Fig. 2.2 Varactor diode equivalent circuit.
Lp Rs(V) Cj(V)
Cp
P + I N +
Fig. 2.3 Physical structure of a PIN diode.
18
7/28/2019 Recon Figt
19/44
Fig. 2.4 PIN diode equivalent circuit.
Lp RsCj
Cp
RjForward bias
reverse bias (rb)
I
50 mA
VB (30 100 V)
V1 V
A few A
Fig. 2.5 I-V characteristics of a PIN diode.
19
7/28/2019 Recon Figt
20/44
CHAPTER 3
TUNABLE ANTENNA TECHNIQUES AND MOBILE PHONE RF
SYSTEM ARCHITECTURE
3.1 INTRODUCTION
Tunable mobile phone antennas are based on the changing of their resonance properties
by an external reactive loading. In theory, the load can be either capacitive or inductive.
The reactive load can be placed either in series or parallel to the original antenna. The
series connection can be achieved by placing the load between the short-circuit and the
ground, and the parallel connection is achieved by loading the antenna between the
ground plane and the radiating element. Due to the space limitations of the mobile phone
antennas, the parallel inductive or series capacitive loading is not very advisable, because
it shifts the resonant frequency upwards. The reactive tuning makes it possible to enhance
the impedance bandwidth of a narrowband antenna over large frequency range. In
practical mobile phone antenna design, however, the feed point of the antenna is usually
placed on a particular point on the radiating patch, which sets limits on the achievable
tuning range. In addition to the fixed feed point, the tunability of a resonator type
20
7/28/2019 Recon Figt
21/44
antenna depends on several other factors, such as the available bias, used tuning
component, coupling of the resonator at zero bias and the characteristics of the antenna
input impedance. The general description of varactor based tuning antenna is introduced
in the next section. Moreover, the concept of switching based technique is described in
section three. In section four, the proposed mobile phone RF sub-system architecture for
dual-band GSM application is presented. Comparison between conventional and the
proposed system is also discussed.
3.2 VARACTOR BASED TUNABLE MICROSTRIP ANTENNASThe use of varactor diodes to tune microstrip antennas has been first introduced in 1982
[16]. In this approach, two varactor diodes are embedded in the patch such that the
symmetry of the patch is retained, which is essential to minimize the cross-polarization
component in the radiation pattern. Fig. 3.1 shows this configuration. A frequency
tuning range of about 30% was achieved depending on the diode characteristics and the
position of the diode in the patch. The structure is half-wavelength which is still too
large for use below 2 GHz. Shorted patch antenna is a good compromise for realizing
high radiation efficiency in a small form factor [17]. Fig. 3.2 illustrate the geometry of a
typical shorted tunable microstrip patch. The antenna length is a quarter wavelength at
the fundamental resonant frequency with the absence of the varactor diode. The
capacitance equivalence of the diode increase the antenna effective length and so reduce
its resonant frequency. Changing the capacitance by changing the bias voltage across the
diode will tune the antenna at the desired frequency. A diode tunable PIFA element that
21
7/28/2019 Recon Figt
22/44
is divided into two sections as shown in Fig. 3.3 has been proposed in [18]. Varactor
tuning diodes are located so they connect the two sections electrically together. The
capacitance between the two sections is controlled by tuning the diodes, which
effectively varies the electrical length, and thus the resonant frequency of the top plate.
Fig. 3.1 Electronic tuning of half-wavelength microstrip antenna.
Fig. 3.2 Electronic tuning of quarter-wavelength shorted microstrip antenna.
Fig. 3.3 Diode tunable PIFA [18].
22
7/28/2019 Recon Figt
23/44
3.3 SWITCHING BASED TUNABLE MICROSTRIP ANTENNAS
Fig. 3.4 shows some possible tuning techniques based on the capacitive or inductive
loading of a /4-resonator antenna [22]. In case (a), the tuning is accomplished by
adding a switchable capacitive load to the open end of the antenna. In cases (b) and (c)
the resonance properties can also be manipulated by modifying the electrical properties of
the short-circuit. The tuning can be achieved either by inserting additional shorting posts
or by modifying the properties of the original short circuit by a series connected
capacitive circuit. In case (b) the inductance of the short-circuit is reduced by increasing
the number of the shorting posts by using of switches. In case (c), the same effect is
achieved by a capacitive switching method. The most pronounced difference between
these two methods is that when the switch is activated to the low impedance state, the
resonance frequency shifts upwards in case (b) and, on the contrary, downwards in case
(c).
23
7/28/2019 Recon Figt
24/44
(a)
Shorting posts
switches
(b)
(c)
(a
capacitor
capacitor
switch
Fig. 3.4 Frequency tuning by switching techniques [22].
(a) Capacitive switching.(a)Tuning by appropriate selection of shorting posts.
(b)Shorting strip with capacitive switch.
24
7/28/2019 Recon Figt
25/44
3.4 THE PROPOSED RF SYSTEM ARCHITECTUURE
GSM system is a frequency-duplex multiple access system. Therefore, the required
handset antenna should cover the transmission and receiving frequency bands
simultaneously. As explained in chapter 1, such bandwidth can be obtained at the
expense of size and/or efficiency (see Fig. 1.2). In this case one antenna that covers
transmission and receiving bandwidths can be used. Fig. 3.5 shows the conventional
dual-band, full duplex front end handset system architecture [21]. Tunable antenna
concept is based on tuning the antenna only at the desired band. So, such antenna would
not cover all the bands simultaneously, but provides narrow instantaneous bandwidths
that are dynamically selectable at higher efficiency than conventional antennas. In this
case, two separate antennas, one for the transmission bands and the second for the
receiving bands should be used. The proposed dual-band front end handset GSM system
architecture is shown in Fig. 3.6. In this configuration, two separate antennas are used,
the first one for transmission at both transmission bands (890-915 MHz for GSM) and
(1710-1785 MHz DCS-1800) and the other for receiving at both receiving bands (935-
960 MHz for GSM) and (1805-1880 MHz for DCS-1800). Control unit and biasing
circuits will be needed to tune both antennas at the desired dynamic frequency of
operation. The design and implementation of dual-band (900 1800 MHz) tunable
antenna is described in the next chapter
25
7/28/2019 Recon Figt
26/44
Fig. 3.5 The conventional dual-band full duplex RF front end [21].
PA
PA
LNA
LNAImage Rejection BPF
Directional
Coupler
TX/RX
Duplexer
TX/RX
Duplexer
BandSeparating
Duplexer
Image Rejection BPF
Power
Detector
Image Rejection BPFNotch filter
Directional
Coupler Combiner
PA
PATransmitting
antenna
PowerDetector
LNA
LNA
Notch filter Image Rejection BPF
SplitterReceivingantenna
Fig. 3.6 The proposed dual-band full-duplex RF front end based on a tunable antenna pair.
26
7/28/2019 Recon Figt
27/44
CHAPTER 4
DUAL BAND TUNABLE ANTENNA FOR CELLULAR PHONE
4.1 INTRODUCTION
Various methods can be used to design compact dual-band antennas. In this chapter we
will introduce a dual-band configuration that can be tuned electronically by the use of
varactor diodes as a variable capacitance device. The proposed structure is small in size,
light in weight, and can be accommodated with active devices and biasing circuits
without the need of excess area. The structure is formed from the integration of a short-
circuited L and inverted-L shape. The resonance property depends on the antenna
geometry and the characteristics of the varactor diode used. The varactor characteristics
and its effect on microstrip circuit are described in the next section. Finally, the analysis
and design of the electronically tunable antenna is presented in the last section.
27
7/28/2019 Recon Figt
28/44
4-2 EFFECT OF VARACTOR DIODES IN MICROSTRIP CIRCUITS
The varactor used for this application is the SMTD3001 silicon-based surface mounted
structure that can be easily used with excellent performance up to 3 GHz. The
capacitance voltage characteristic is shown in Fig. 4.1. The diode can operate well in
temperature range from -65o
to 150o. Since, the power supply of the handset mobile
phone is a 3-V battery, we will only be interested in the portion from 0-3 V of the curve.
The junction capacitance values in this range are shown in Table 4.1. The maximum
capacitance can be obtained when zero voltage is applied is 2.2 pF, while the minimum
capacitance is limited by the maximum available voltage, 3-V in mobile handset, is 1.15
pF. Since the diode is usually located at the end of an open circuit line, its effect can be
analyzed as a section of the line with the same width and effective electrical length effas
shown in Fig. 4.2. The effective electrical length effof the diode junction capacitance Cj
can be calculated as a function of the radian frequency and line characteristic
impedance as eff= cot-1
C/Zo
Fig. 4.3 shows the variation of the effective electrical length of the varcator capacitance
against microstrip line width on a Duroid substrate with r = 2.2 and of 1.57 mm
thickness. The curves are calculated for the minimum and maximum capacitances (1.15
and 2.2 pF) at 900 MHz, Fig. 4.3a, and at 1800 MHz, Fig. 4.3b. It is clear from these
curves that, the effective length decreases as the line width increases and the maximum
effective length is obtained at zero bias voltage which corresponds to 2.2 pF. For a line
of width 2 mm, this junction capacitance is equivalent to about 45o, at 900 MHz and more
than 65o
at 1800 MHz. These curves are helpful in the design stage, in order to integrate
the effect of the varactor diode in the initial design.
28
7/28/2019 Recon Figt
29/44
Fig. 4.1 Capacitance-Voltage relation of SMTD3001.
Fig. 4.2 Electrical length equivalence of a varactor located at the end of the line.
eff
Table 4.1: change of junction capacitance with bias voltage of the SMTD3100 varactor diode
Reverse bias voltage (V) Junction capacitance (pF)
0 2.2
.3 2
.8 1.6
1 1.5
2.2 1.25
3 1.15
29
7/28/2019 Recon Figt
30/44
0
10
20
30
40
50
2 4 6 8 10 12 14 16
Cj = 1.15 pF
Cj = 2.2 pF
Microstrip line width (mm)
eff(degrees)
(a)
Fig. 4.3 The variation of effective electrical length of the varactor diode SMTD3001
against microstrip line width on Duroid substrate with r= 2.2 and 1.57 mm thickness(a)at 900 MHz
(b)at 1800 MHz.
0
10
20
30
40
50
60
70
2 4 6 8 10 12 14 16
Effectiveelectricallength
(degrees)
Cj = 2.2 pF
b
Microstrip line width (mm)
Cj = 1.15 pF
30
7/28/2019 Recon Figt
31/44
4.3 COMPACT TUNABLE MICROSTRIP ANTENNA
As shown in Fig. 4.4, the antenna under consideration consists of two resonant elements
an inverted large L-shape element that resonates at the lower frequency (Fig. 4.4a) and
another smaller L-shape element that resonates at the higher frequency (Fig. 4.4b) [25].
The effective electrical lengths of the lines are 1 and 2, where the corresponding
physical lengths are l1, and l2, at the lower frequency and l1, and l2, at the higher
frequency, taking the discontinuities effect into account. Z1 and Z2 are the characteristic
impedances of the microstrip lines of widths W1 or W1 and W2 or W2 respectively. At
resonance
tan 1 tan 2 = K (4.1)
where K is the ratio of the line impedances; K = Z2 / Z1. Equation (4.1) gives the
resonance condition without considering the varactor diode at the ends of l2 and l2 lines.
Now, consider the varactor diodes connected to the patch as shown in Fig. 4.5. Biasing
circuit consists of coupling capacitor 3 pF, and RF chock coils is used with each diode to
provide biasing voltage. The effect of the varactor diode in the circuit can be treated as a
transmission line section, having the same line width (W2), with an effective electrical
length eff as described in Fig. 4.3. In this case the resonance condition defined by
equation (4.1) is modified as
tan 1 tan (2 + eff) = K (4.2)
31
7/28/2019 Recon Figt
32/44
(a)
W1
W2
l1
l2
Fig. 4.4 L and inverted L shape antenna [25].
a) L-shaped antenna that operates at the lower frequency.
b) L-shaped antenna that operates at the higher frequency.
c) Integration of (a) and (b).
(b)
l1
l2
W1
W2
(c)
Fig. 4.5 The proposed dual-band tunable microstrip antenna.
V1 V2Probe feed
Shorting post
32
7/28/2019 Recon Figt
33/44
Using equation (4.2) (2 + eff) is plotted against 1 for different values of K in Fig. 4.6. It
is observed that, for a certain value of1, (2 + eff) decreases as K decreases resulting
in a reduction of the total antenna size. The total electrical length of the antenna is given
by t = 1 (2 + eff). For K = 1 (uniform resonator), the total electrical length is 90o
and the total length decreases as K decreases .
Fig. 4.6 is a helpful graph for a primary design of each antenna element through judicial
selection of the K factor, and hence the selection of electrical lengths of the antenna arms.
The design and implementation of the dual-band tunable antenna at the GSM/DCS1800
bands is achieved on Duroid dielectric substrate with r = 2.2 and thickness 1.57 mm.
The width of the narrow lines W1 and W1 are chosen to be 4 mm to avoid degradation of
the antenna efficiency and the width of the wider line is selected for a suitable value of
the impedance ratio K to achieve antenna size reduction and concurrently to maintain the
validity of transmission line approximation. We choose W2 = 10 mm and W2 = 7 mm to
provide a suitable radiation aperture at the 900/1800 MHz bands. The characteristic
impedances corresponding to these dimensions are Z1 = Z1 =56.5 , Z2 = 29.5 , and
Z2 = 38.5 , which yield K value of 0.52 at 900 MHz and 0.68 at 1800 MHz. The
effective electrical length of the varactor diode at zero bias in this case is 20o
at 900 MHz
and about 44o
at 1800 MHz. Fig. 4.6 provides good tool to hit a compromise point
between 1 and 2 for both antenna elements. Interpolation between the K - curves can be
used to predict the K = 0.52 curve at 900 MHz and 0.68 at 1800 MHz. The junction
capacitance is very sensitive with the reverse voltage applied zero volts. Therefore, the
frequency change per volt increases in this region that will need a sophisticated voltage
control circuit. To avoid this, the physical size of this structure is optimized to cover the
33
7/28/2019 Recon Figt
34/44
GSM bands (890 960 MHz & 1710 1880 MHz) in tuning range between 0.8 V to 3 V.
The antenna physical dimensions after adding the discontinuity effects, are l1= 14.5, l2 =
22.5, l1= 5 and l2 = 8 mm. The discontinuity effects are calculated with the help of IE3D
software; a commercial electromagnetic simulator based on an integral equation method
and the method of moment. The layout of the designed antenna is shown in Fig. 4.7.
Simulations are carried out using IE3D. A series of simulations have been performed for
various values of junction capacitance representing the vractor diodes and biasing circuit.
The return losses (S11) for this antenna for different values of junction capacitance, or
corresponding voltage, at lower band are shown in Fig. 4.8. Variation of resonance
frequency from 826 MHz to 944 MHz is observed for voltage variation from 0 to 3 V.
This means that the, bandwidth the antenna can be tuned within the 3-V battery is about
118 MHz. This is more than the GSM bandwidth requirements at 900 MHz. Good
matching is maintained within this band. At 1800 MHz the simulation results are shown
in Fig. 4.9 for the smaller patch. From 0 to 3 V, the smaller antenna can be tuned from
1440 MHz to 1890 MHz. The tunable bandwidth is 450 MHz. This bandwidth is more
than the DCS-1800 requirements. In this case, we can avoid tuning near the zero voltage
in order to alleviate the frequency sensitivity and provide more stability. The variation of
the resonance frequencies, f1 of the larger patch and f2 for the smaller patch, against
biasing voltage, are shown in Fig. 4.10. The simulated far field radiation patterns at two
different frequencies for each band are shown in Fig. 4.11. Almost no significant
variation for difference biasing conditions is observed. The gain for all cases is about 2.6
dB. These characteristics are adequate for mobile phone requirements.
34
7/28/2019 Recon Figt
35/44
1
2
+
eff 4
23
0.8
1
0.4
0.
0.2
Fig. 4.6 1 versus (2 + eff) for different values of K.
a small patch for interconnectionbetween ground/varactor and RF
chock
22.5 mm
10 mm
7 mm
8 mm
4 mm
3 mm
14.5 mm
12 mm
Fig. 4.7 Layout of the dual-band tunable antenna designed for GSM applications.
a small patch for
ground connection
a small patch for
terminal voltage
connection
35
7/28/2019 Recon Figt
36/44
Fig. 4.8 Simulation results (S11) of the dual band proposed antenna at the lower
frequency band (GSM-900 MHz) for various values of reverse bias voltage VR.
-25
-20
-15
-10
-5
0
0.8 0.85 0.9 0.95 1
VR= 0.3 Vf1 = 846 MHz
VR= 1 V
f1 = 900 MHz
VR= 2.2 V
f1 = 930 MHzVR= 3 V
f1 = 944 MHz
VR= 4 V
f1 = 964 MHz
VR= 0 V
f1 = 826 MHz
f1 (GHz)
S11 (dB)
-25
-20
-15
-10
-5
0
1.4 1.5 1.6 1.7 1.8 1.9 2
Fig. 4.9 Simulation results (S11) of the dual band proposed antenna at the higher
frequency band (DCS-1800 MHz) for various values of reverse bias voltage VR.
f2 (GHz)
S11 (dB)
VR= 0.3 Vf2 = 1502 MHz
VR= 1 V
f2 = 1698 MHz
VR= 2.2 V
f2 = 1830 MHz
VR= 3 V
f1 = 1890 MHz
VR= 4 V
f1 = 1994 MHz
VR= 0 V
F2 = 1440 MHz
36
7/28/2019 Recon Figt
37/44
0.8
1
1.2
1.4
1.6
1.8
2
0 1 2 3
f1
Resonancefrequency(G
Hz)
f2
4
Bias voltage VR (V)
Fig. 4.10 Resonance frequencies of the dual band proposed antenna
against reverse bias voltage VR.
37
7/28/2019 Recon Figt
38/44
Fig. 4.11 Far field simulated radiation patterns at different bias conditions
(a) Radiation pattern at 900 MHz (VR= 1 V).(b) Radiation pattern at 930 MHz (VR= 2.2 V).
(c) Radiation pattern at 1502 MHz (VR= .3 V).
(d) Radiation pattern at 1700 MHz (VR= 1 V).
(a)
(d)
(b)
(c)
38
7/28/2019 Recon Figt
39/44
4.4 EXPERIMENTAL RESULTS
The tunable antenna designed in the above section is implemented and tested. The layout
of the circuit is shown in Fig. 4.7. The double coated Duroid substrate with r = 2.2 and
1.57 mm thickness is manipulated by the available grooving machine. The chock coils
and varactor diodes are soldered on the same side where the antenna is implemented. An
HP8510A vector network analyzer is used to measure the return loss of the antenna (S11)
at different biasing conditions. The biasing voltage is provided by a dc voltage source.
V1 denotes the biasing voltage for the larger element (resonates at the lower band), and
V2 denotes the biasing voltage for the smaller element (resonates at the higher band).
The measured data are presented in Fig. 4.12. The return losses change from -8 to -15 dB
at different resonances corresponding to voltage changes from 0 to 3 V. The degradation
in return loss as compared to simulation results is attributed to the limitation of the
accuracy of the available fabrication and mounting tools. Frequency shift of about -100
MHz is observed at all biasing voltages. This is attributed to the accuracy of the varactor
diode capacitance. Varactor datasheets indicate that the capacitance accuracy can be
changed in the order of 20%. More than 100 MHz frequency shift results from such
limited accuracy. Usually, carefully designed devices give better results. Also, this
drawback can be overcome by either individually characterizing the varactor diodes or
retune the antenna circuit to compensate for this effect. On this context, another
alternative which yields better results was obtained at the lower band by adding a small
adhesive foil patch to increase the width W1 of the patch. As W1 increases, Z1 decreases
and thus K (Z2/Z1) increases, and so from Fig. 4.6, the corresponding (2 + eff) increases
39
7/28/2019 Recon Figt
40/44
that leads to increase of resonance frequency. The modified measurements are shown in
Fig. 4.13.
-20
-15
-10
-5
0
0.7 0.8 0.9 1
-20
-15
-10
-5
0
1.2 1.3 1.4 1.5 1.6 1.7 1.8
Frequency (GHz) Frequency (GHz)
S11(dB)
S11(dB)
Fig. 4.12 Measured return loss of the tunable antenna for reveres bias of 0,
1, and 3 V(a) Lower band tuning.
(b) Higher band tuning.
VR= 0 V
f1 = 740 MHzVR= 1 V
f1 = 780 MHz
VR= 0 Vf2 = 1300 MHz
VR= 3 Vf1 = 840 MHz
VR= 1 V
f2 = 1480 MHzVR= 3 V
f2 = 1630 MHz
(b)(a)
-20
-15
-10
-5
0
0.7 0.8 0.9 10.8 0.9 1.0 1.1
Fig. 4.13 Measured return loss of the tunable antenna for reveres bias of 0,
1, and 3 V for a modified lower band element.
Frequency (GHz)
S11(dB)
VR= 0 Vf1 = 832 MHz
VR= 1 Vf1 = 900 MHz
VR= 3 Vf1 = 930 MHz
40
7/28/2019 Recon Figt
41/44
CHAPTER 5
CONCLUSIONS AND RECOMMENDATION
In this project a tunable compact microstrip antenna concept has been studied as a
solution to virtually increase the antenna bandwidth without increasing its size or
reducing its efficiency. In this study, varactor diode has been used as a voltage control
capacitance. The main characteristics of varactor diode have been reviewed. The effect
of loading microstrip lines of different widths by a varactor diode has been analyzed
based on transmission line theory. A design procedure has been developed in chapter 4.
Based on that, a dual-band antenna has been designed for GSM/DCS-1800 bands. The
antenna structure has been selected to integrate the biasing circuit and the varactor diodes
without significant increase the structure area. Duroid dielectric substrate with r = 2.2
and thickness of 1.57 mm has been used. The IE3D simulator has been used to verify the
antenna performance before implementation. It has been shown that, the required
bandwidth can be easily covered using voltage changes from 0 to 3V, available from the
battery of mobile handset. Approximate omni directional similar radiation pattern at
different biasing voltages suitable for handset mobile phones has been observed. The
calculated antenna gain obtained from the simulation was reported as 2.6 dB for all
biasing condtions. The measurements have been performed using HP8510A vector
network analyzer. A frequency shift of about 100 MHz, compared to simulation results,
41
7/28/2019 Recon Figt
42/44
has been noticed in the measurements. This shift is attributed to the accuracy of the
capacitance of the low cost varactor diode STMD3100. This frequency shift has been
treated at the lower band by adding a small piece of copper foil made for this purpose.
From the proposed RF system architecture of a mobile handset that can use tunable
antenna, the RF system needs two separate antennas. The first antenna is for the
transmitter and the other for the receiver. Each antenna consists of two elements, two
varactors and two biasing circuit. Since, the antenna used is the short-circuit quarter-
wave branches, two coupling capacitors are needed to isolate biasing voltage from the
ground. In conclusion the basic disadvantage of the tunable antenna is the large number
of components needed for operation which contribute to additional cost. In this regard,
an antenna design with less number of passive and active devices is required and attracts
the attention and effort of researchers in the field of microstrip antennas and circuits.
42
7/28/2019 Recon Figt
43/44
REFERENCES
[1] R. C. Hansen, Fundamental limitations in antennas, Proc. IEEE, Vol. 69, pp.170-182, Feb. 1981.
[2] J. T. Bolljahn and R. F. Reese, Electrically small antennas and the low-
frequency aircraft antenna problem, IRE Trans. Antennas Propagat., Vol. 1, pp.
46-54, Oct. 1953.[3] J. C. -E. S. Sten, A. Hujanen, and P. K. Koivisto, Quality factor of an
electrically small antenna radiating close to a conducting plane, IEEE Trans.Antennas Propagat., Vol. 49, pp. 829-837, May 2001.
[4] F. R. Hsiao and K. L. Wong, Compact planar inverted-F patch antenna for
triple-frequency operation, Microwave Opt. Technol. Lett., Vol. 33, pp.459462, June, 2002.
[5] W. P. Dou and Y. W. M. Chia, Novel meandered planar inverted-F
antenna for triple-frequency operation, Microwave Opt. Technol. Lett.,
Vol. 27, pp. 5860, Oct. 5, 2000. Dig., pp. 112115.[6] Z. D. Liu, P. S. Hall, and D. Wake, Dual-frequency planar inverted F
antenna, IEEE Trans. Antennas Propagat., Vol. 45, pp. 14511458, Oct.1997.[7] C. R. Rowell and R. D. Murch, A compact PIFA suitable for dual-
frequency 900/1800-MHz operation, IEEE Trans. Antennas Propagat.,
Vol. 46, pp. 596598, April 1998.[8] S. Tarvas and A. Isohatala, An internal dual-band mobile phone antenna,
in Proc. IEEE AP-Symp., pp. 266269,2000.
[9] P. Salonen, M. Keskilammi, and M. Kivikoski, Single-feed dual-band
planar inverted-F antenna with U-shaped slot, IEEE Trans. AntennasPropagat., Vol. 48, pp. 12621267, August 1998.
[10] G. H. K. Lui and R. D. Murch, Compact dual-frequency PIFA designsusing LC resonators, IEEE Trans. Antennas Propagat., Vol. 49, pp. 1016
1019, July 2001.
[11] F. R. Hsiao, H. T. Chen, G. Y. Lee, T. W. Chiou, and K. L. Wong, A dual-band planar inverted-F patch antenna with a branch-line slit, Microwave
Opt. Technol. Lett., Vol. 32, pp. 310312, Feb., 2002.
[12] C. W. Chiu and F. L. Lin, Compact dual-band PIFA with multi-resonators, Electron. Lett., Vol. 38, no. 12, pp. 538-539, 2002.
[13] S. K.won, H. K. Yoon, and Y. J. Yoon, Harmonic tuning antennas using
slots and short-pins, IEEE AP-Symp., pp.118-121, 2001.[14] V. A. Dmitriev, and J. C.W. Costa, Theoretical investigation of compact
microstrip resonators with stubs for patch antennas, IEEE Trans.
Microwave Theory Tech., Vol. 50, pp. 2729, January 2002.
[15] R. Al-Dahleh, L. Shafai, and C. Shafai, A frequency tunable mechanicallyactuated microstrip patch antenna, IEEE AP-Symp., pp.548-551, 2003.
[16] P. Bahartia, and Bahl, Frequency agile microstrip antenna, Microwave
Journal, pp. 67-70, Oct. 1882.[17] P. K. Panayi, M. O. Al-Nuaimi, and L. P. Ivrissimtzis, Tuning techniques for
planar inverted-F antenna, Electron. Lett., vol. 37, no. 16, pp. 1003-1004, 2001.
43
7/28/2019 Recon Figt
44/44
[18]K. L. Virga, and Y. R. Samii, Low-profile enhanced-bandwidth PIFA antennas
for wireless communications packaging, IEEE Trans. Microwave Theory Tech.,Vol. 45, pp. 18791888, October 2002.
[19]J. Ollikainen, O. Kivekas, and P. Vainikainen, Low loss tuning circuits for
frequency-tunable small resonant antennas, IEEE PIMRC, pp. 1882-1887, 2002.
[20]
H. Okabe and K. Takei, Tunable antenna system for 1.9 GHz PCS handsets,in Proc. IEEE AP-Symp., pp.166-169, 2001.
[21]J. T. Aberle, S. H. Oh, D. T. Auckland, and S. D. Rogers, Reconfigurableantennas for portable wireless devices, IEEE Antennas and Propagation
Magazine, Vol. 45, No. 6, December 2003.
[22] N. C. Karmakar, Shorting strap tunable stacked patch PIFA, IEEE Trans.Antennas Propagat., Vol. 52, pp. 28772884, November 2004.
[23] D. Peroulis, K. Sarabandi, and L. Katehi, Design of reconfigurable slot
antennas, IEEE Trans. Antennas Propagat., Vol. 53, pp. 645654, February
2005.[24] K. Chang, Microwave Solid-State Circuits and Applications, John Wiley &
Sons, Inc, USA, 1994.[25] M. Alkanhal, A New Multi-Band Antenna for GSM/DCS/GPS Systems,Technical Report, Research Center, College of Engineering, KSU, grant number
7/425, 2005.