SCX- 4200 Ser i es
1. Dr i ver• Common I ns t al l er• GDI Pr i nt er Dr i ver• Twai n, WI A ( SM) Smar Thr u4• Mac Pr i nt er /Twai n• Li nux dr i ver s
2. Fi r mwar e3. Har dwar e4. Mechani s m
Common I ns t al l erCommon I ns t al l er
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
AgendaAgenda
I. Installation Procedure MapII. Maintenance Procedure MapIII. Common Installer Dialog DetailsIV. Trouble Shooting
Ⅰ. Installation Procedure Map
ObjectivesObjectives
I. To show the installation
procedure map
Ⅰ. Installation Procedure Map
Ⅰ. Installation Procedure Map – Typical Installation
Welcome
Select Component
Test Print
Test Print Confirm
Setup Completed
Select Installation Type Copy FilesInstall Components
Connect Device
Typical
Typical
Ⅰ. Maintenance Procedure Map
Select Component
Connect Device
Test Print Test Print Confirm
Copy Files Install Components Setup Completed
Select Component Uninstall Components Uninstall Completed
Repair
Remove
Maintenance
Ⅱ. Common Installer Dialog Details
ObjectivesObjectives
I. To describe the dialog
details
Ⅱ. Common Installer Dialog Details
Vi ew Us er ’ s Gui de : I t s hows Us er ’ s
Gui de. I f Acr obat Reader i s not
i ns t al l ed i n t he comput er , i t
t r i es t o i ns t al l Acr obat Reader
aut omat i cal l y.
Changi ng Language : I t of f er s t he
opt i on t hat us er can s el ect
des i r ed s of t war e and change an
i ns t al l i ng l anguage.
Welcome Dialog
Ⅱ. Common Installer Dialog Details - Installation
Typi cal : I t i ns t al l s t he def aul t
component s f or l ocal pr i nt er .
Cus t om : I t of f er s t he opt i on t hat
us er can s el ect des i r ed s of t war e
Select Installation Type Dialog
Ⅱ. Common Installer Dialog Details - Installation
Thi s di al og r ecommends a us er t o
connect a pr i nt er t o us er ’ s
comput er when no pr i nt er i s
connect ed.
When i ns t al l er i s execut ed,
I ns t al l er wi l l s ear ch t he connect ed
devi ce aut omat i cal l y.
To i ns t al l t he devi ce, connect i t
and s el ect next but t on.
Pr i nt er por t i s s et wi t h t he
det ect ed por t .
Connect Device
Ⅱ. Common Installer Dialog Details - Installation
Note: In case of printer product that has only USB I/F port, only USB port picture will be shown to guide how to plug-in device.
Select Components
Ⅱ. Common Installer Dialog Details - Installation
Select Components: Us er can s el ect s
des i r ed s of t war e component s i n Cus t om
i ns t al l at i on
Pr i nt er Dr i ver : This component enables you to print
documents. (Mandatory item)
Scanner Dr i ver :This is a driver to scan documents using the
local device (Mandatory item in Type 103 model)
Pr i nt er Set t i ngs Ut i l i t y/ Remot e Cont r ol Panel :
This component allows a user to change configuration parameters
Net wor k Scan: Allows you to scan through Network printer.
Set I P : Allows you to configure a network printer's IP address
Smar t Panel : shows current status of the printer.
Change Des t i nat i on Fol der : Us er can
change t he des t i nat i on f ol der wi t h us i ng t hi s
but t on.
Note: The supported component is depending on Model
Test Print
Tes t Pr i nt hel ps a us er t o ver i f y
i f pr i nt er dr i ver i ns t al l at i on
s ucceeds or f ai l s . ( Sel ect abl e)
I f Tes t Page i s nor mal l y pr i nt ed,
pr i nt er dr i ver i ns t al l at i on i s
s ucces s f ul l y compl et ed.
I f a us er i ns t al l s dr i ver wi t hout
connect i ng t he pr i nt er , Tes t
Pr i nt di al og wi l l not be
appear ed.
Thi s di al og i s s hown onl y
i ns t al l at i on f or l ocal pr i nt er .
Ⅱ. Common Installer Dialog Details - Installation
Maintenance
Repai r : r epai r s i ns t al l ed dr i ver
and s of t war e.
I f t her e i s one or mor e i ns t al l ed pr i nt er s ,
t he i ns t al l er wi l l r emove al l t he i ns t al l ed
pr i nt er s and i ns t al l onl y one pr i nt er .
I t can be us ed i n r ecover i ng f unct i on when
dr i ver and appl i cat i on ar e damaged or out of
dat e.
Net wor k s can and Smar Thr u ar e not r epai r ed by
t hi s i ns t al l er .
Remove : I t wi l l r emoves i ns t al l ed
dr i ver and s of t war e. ( Removabl e
component i t ems wi l l be s hown i n
s el ect i on i t em di al og )
Mai nt enance i s not s uppor t ed f r om
CD. To mai nt enance, f ol l ows next
s t eps .
1. Start -> Programs
2. Click Model Name
3. Click “Maintenance”
Ⅱ. Common Installer Dialog Details - Maintenance
Note: The supported component is depending on Model
Dur i ng t he i ns t al l at i on of a pr i nt er , t he i ns t al l er cr eat es “Dr . Pr i nt er ”
s hor t - cut i n t he des kt op of a us er ’ s comput er .
When “Dr . Pr i nt er ” s hor t - cut i s execut ed, i t opens a homepage of t he Sams ung
Dr . Pr i nt er .
The Sams ung Dr . Pr i nt er makes eas y f or us er s t o di agnos e t he pr i nt er and
updat e s of t war e.
Ⅱ. Common Installer Dialog Details
ObjectivesObjectives
I. To support the solution
about problems from
installation
ⅢⅢ.. Trouble Shooting
New Hardware Wizard
I f a us er connect t he pr i nt er ,
t he New har dwar e f ound wi zar d
di al og wi l l be popped up onl y
one t i me but i f a us er connect
t he MFP, t he new har dwar e f ound
wi zar d di al og wi l l be popped up
s ever al t i mes . Whenever t he new
har dwar e f ound wi zar d i s popped
up, pl eas e cancel t he di al og.
ⅢⅢ.. Trouble Shooting
ⅢⅢ.. Trouble Shooting
Br oken s t r i ngs i s f ound on t he pr i nt ed paper
Check def aul t s et t i ngs of pr i nt er dr i ver
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Pr i nt er s
2. Whet her connect ed pr i nt er i s t he def aul t pr i nt er ?
Er r or occur s when a pr i nt er i s connect ed t o USB por t
1. Tur n of f t he pr i nt er .
2. Tur n on t he pr i nt er af t er 5 mi n.
1. Connect t he pr i nt er t o t he USB por t
2. Pr oceed t he i ns t al l at i on af t er r eboot i ng
the default printer has
check mark on the
printer icon
♣ In Windows NT, click
mouse right button. It
should be checked to
the “Set as Default
Printer”
ⅢⅢ.. Trouble Shooting
Por t er r or occur s i n Wi ndows 2000/ XP
Check t he def aul t pr i nt er
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Pr i nt er s
2. Ver i f y t he def aul t pr i nt er .
Check Por t
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Pr i nt er s
2. Sel ect Pr oper t i es af t er r i ght cl i ck on Pr i nt er i con
3. Go t o Por t t ab and check connect ed por t
4. Comput er has mul t i pl e USB por t s , do r e- i ns t al l dr i ver af t er pl uggi ng i n
devi ce wi t h USB cabl e.
ⅢⅢ.. Trouble Shooting
OS l anguage and I ns t al l pr ogr am l anguage ar e di f f er ent
1. Pr oceed i ns t al l at i on as Cus t om i ns t al l
2. Change t he l anguage s el ect i on i n Sel ect Component di al og
ⅢⅢ.. Trouble Shooting
I f t he PnP di al og pr ompt s t he us er t o l ocat e s peci f i c f i l es dur i ng
i ns t al l at i on
I ns er t t he CD i nt o t he CD Rom.
Des i gnat e t he pr i nt er dr i ver f i l es or s canner dr i ver f i l es di r ect or y i n t he CD.
RPC er r or occur s dur i ng i ns t al l at i on
Check Spool Ser vi ce af t er Vi r us check
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Admi ni s t r at i ve Tool s - > Ser vi ces
2. Check whet her Pr i nt Spool er and Remot e Pr ocedur e Cal l s er vi ce ar e r unni ng. I f
t hes e s er vi ces ar e not r unni ng, s t ar t t hes e s er vi ces .
ⅢⅢ.. Trouble Shooting
I f an er r or occur i n pr i nt i ng, check f ol l owi ngs
Check t he i ns t al l ed dr i ver pr oper l y
Check t he pr i nt er por t
Check t he def aul t pr i nt er
Check Spool Ser vi ce af t er Vi r us check
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Admi ni s t r at i ve Tool s - > Ser vi ces
2. Check whet her Pr i nt Spool er and Remot e Pr ocedur e Cal l s er vi ce ar e r unni ng. I f
t hes e s er vi ces ar e not r unni ng, s t ar t t hes e s er vi ces .
ⅢⅢ.. Trouble Shooting
The pr i nt er i s s et as Unknown Devi ce af t er s et connect i on i n Wi ndows 98
1. Del et e or Unknown Devi ce i n t he Devi ce Manager
2. Tur n of f t he pr i nt er
3. Tur n on t he pr i nt er af t er 2 mi n.
Pr i nt er dr i ver i s not i ns t al l ed
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Pr i nt er s
2. Pr oceed i ns t al l at i on t hr ough Add Pr i nt er
ⅢⅢ.. Trouble Shooting
Compos i t e devi ce i ns t al l at i on f ai l
Del et e or Unknown Devi ce i n t he Devi ce Manager
MS USB dr i ver er r or di al og occur s
1. Del et e or Unknown Devi ce i n t he Devi ce Manager
2. Reconnect t he s et af t er r eboot i ng
ⅢⅢ.. Trouble Shooting
How t o Open Devi ce Manager
1. Ri ght cl i ck on My comput er i con i n des kt op
2. Sel ect Pr oper t i es
3. Sel ect Har dwar e t ab
4. Cl i ck Devi ce Manager but t on
1. St ar t - > Set t i ngs - > Cont r ol Panel - > Sys t em
2. Sel ect Har dwar e t ab
3. Cl i ck Devi ce Manager but t on
ⅢⅢ.. Trouble Shooting
I f you want t o as k about pendi ng pr obl em t o t he head of f i ce, pl eas e
at t ach t he i nf or mat i on f i l e of t he comput er i n whi ch t he pr obl em occur s .
I nf or mat i on f i l e at t achment met hod
1. St ar t - > Pr ogr ams - > Acces s or i es
2. Sys t em Tool s - > Sys t em I nf or mat i on
3. Cl i ck Act i on - > Save as Sys t em I nf or mat i on f i l e
GDI Pr i nt er Dr i verGDI Pr i nt er Dr i ver
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
ObjectivesObjectives
I. To know what is the printer
driver?
II. To know what the functions
are supported by Eiger SPL
driver?
1. Introduction to Printing
The Microsoft® Windows® printing architecture consists of a print spooler and a set of printer drivers.
Print jobs are created by applications through calls to Microsoft® Win32® GDI functions.
1-1. Printing Process
GDI
Driver
SpoolerPrinting Image
Creating commands
Rendering Image
Sending Data to Printer
Printing Image on Paper
1-2. Printer driver
Is a software on PC.
Is consist of printer graphics DLL and printer interface DLL.
Printer graphics DLL
ㆍAssists to render a print job with GDI, and sends the rendered data stream to the print spooler.
ㆍChanges device-independent commands to device-dependent commands.
Printer interface DLL
ㆍProvides a user interface to the driver's configuration parameters.
%-12345X@PJL SET PAPERTYPE = OFF@PJL DEFAULT TIMEOUT = 15@PJL SET DENSITY = 3@PJL DEFAULT POWERSAVE = ON@PJL DEFAULT POWERSAVETIME = 5@PJL SET RET = OFF@PJL SET JAMRECOVERY = OFF@PJL SET REPRINT = ON@PJL ENTER LANGUAGE = SMART$PJL JOB START$PJL RESOLUTION = 600$PJL COPIES = 1$PJL PAGE A4 AUTO$PJL BITMAP STARTtypedef struct{ DWORD ulBandSize; WORD usBandNo; BYTE ubCompMode; BYTE ubLeft; WORD usBandHeight; WORD usBandWidth;} BND_HDR;Real Bitmap Compressed$PJL PRINT 4$PJL EOJ$PJL SYNC$PJL RELEASE 0 2047$PJL GARBAGE%-12345X
%-12345X@PJL SET PAGEPROTECT=OFF@PJL SET RESOLUTION=600@PJL ENTER LANGUAGE=PCLE*t600R&u600D*r0F&l0O&l0S&l0H&l26a8c1E*p0x0Y*c0t5594x8201Y&l1X*b0M*p720Y*p450X(19U(s16602t0b0s10v1P1E%-12345X
GDIWindows 9x/NT/2000/XP
PCLMS-DOS/All Windows
File Capture Method
1-3. PCL VS. SPL
SPL PCL PSNo s t andar d ( Can’ t us e ot her company’ s dr i ver )
HP Adobe
Bi t map Bas ed Command Bas ed Command Bas edNeed hi gh per f or mance comput er
Need hi gh per f or mance pr i nt er
Need ver y hi gh per f or mance pr i nt er
Low cos t pr i nt er Hi gh cos t pr i nt er
Ver y hi gh cos t pr i nt er
SPL (Samsung Printer Language)
PCL (Printer Control Language)
PS (PostScript)
2. Eiger
Using SPL printer driver.
Support Microsoft® Windows® 98, Me, NT 4.0, 2000 and XP
2-1. Overview
App. DriverGDI
Spooler Printer
Windows component
Driver component
Framebuffer
LanguageMonitor
PortMonitor
1 2
3 4
5
6
7
• Overall Architecture
16bits Driver 32bits Driver
UI DLL(16bits) PSUI
SmartUI(32bits) HelpData File
Spooler
LanguageMonitor
64bits Driver
PSUI
Windows XP
64bit Edition
• Driver Component
Render
Color Matching
Halftone
Compression
Emulation
Product Value Comment
Mono LBP
0 Command Mode(no USE)
1 SPL I (Scanline & Tiff) : for Mono MFP
2 FBB & LZW
3 PCL5e
4 PCLXL
5 Old GDI
6 Banded JBIG
7 Full Page JBIG
Color 10 BigBang
11 Banded Color JBIG
12 Full Page Color JBIG
Photo 20 JPEG
LanguageMonitor
PortMonitor
• Rendering Component
Orientation 2-2. Printer driver settings
Orientation allows you to select the direction of the printed page. You can select another Orientation by clicking the appropriate radio button. The default is Portrait.
Your choices are: - Portrait (Select to print page that is taller than it is wide) - Landscape (Select to print page that is wider than it is tall)
Multiple pages per side 2-2. Printer driver settings
You can specify how many pages to print per sheet. The default is 1. The available options are: 1/2/4/9/16
Page Order : Select the order and placement of the pages on the sheet. Print Page Borders check box allows you to print border around each page on the sheet.
NOTE : When the value of Multiple Pages per Slide is 1, Page Order and Print Page Borders are grayed out and not available.
Poster2-2. Printer driver settings
Poster allows you to print large, multiple-sheet versions of your page. Style allows you to choose how many pages should be printed when you print a poster. The default is 2 x 2.
For instance, 2 x 2 will result in 2 page long and 2 pages wide for a total of 4 pages.
Available Poster Styles are: 2 x 2, 3 x 3, 4 x 4.
Copies2-2. Printer driver settings
Copies allows you to choose the number of uncollated copies to print. The default is 1 and you can select up to 999. You can type the number of copies you want or use the up and down arrows to scroll to the desired number of copies.
NOTE: This setting is independent of the Copies selection that may appear within the software application print dialog box. To avoid conflicts and delays, do not use the two settings simultaneously.
Paper size2-2. Printer driver settings
Paper Size allows you to choose the size of the paper or envelope you are printing.
NOTE : It is possible that the application software you are using may override this setting. If there are problems, check that the application software is set to the same Paper Size as the printer.
When the user clicks the button Add Custom, the Custom Page Size dialog appears, and the user can create a user defined paper size.
Paper type2-2. Printer driver settings
Use the Paper Type drop-down list for selecting the type of paper loaded in the tray from which you want to print.
The default value is Printer Default.
Reduce/Enlarge2-2. Printer driver settings
Reduce/Enlarge allows you to reduce and enlarge the print. Scale factor allows you to set the reduction or enlargement value as a percentage of the original page.
The default value is 100%. The available value is from 25% to 400% in intervals of 1%.
Fit to Page2-2. Printer driver settings
Fit to Page allows you to reduce or enlarge your document to fit on the selected paper size.
You can choose any supported paper size from the Fit to Page dropdown list.
Resolution2-2. Printer driver settings
Resolution defines the quality of the print output in simplest form: the number of dots per inch.
Resolutions available are 600 dpi (Normal) and 300 dpi (Draft). The default value is 600 dpi (Normal).
Toner save2-2. Printer driver settings
Toner Save setting allows the user to save printing toner when printing a draft version of a document.
Select Off to print in normal mode and select On to print with less toner applied to the page. The default value is Printer Setting.
True type option2-2. Printer driver settings
This option controls the method of printing TrueType font. Generally TrueType option Download as Bit Image can print faster. But if the document contains graphics and strings in the text are non repetitive, then it is better to select the TrueType option Print as Graphics.
(This option is only available at Windows 9x and Me)
Print all text black2-2. Printer driver settings
When the Print All Text Black is checked, all the text in your document is printed in solid black, regardless of the color it appears on the screen. When it is not checked, colored text is printed in shades of gray.
Watermark2-2. Printer driver settings
Watermark drop-down list allows the user to enable or disable the watermark feature.
Edit Watermarks dialog allows users to enable or disable the watermark feature. It also allows users to create and save new watermarks. The preview area on the right of the list shows how the page will look when it is printed
Edit Watermark Dialog2-2. Printer driver settings
Overlay2-2. Printer driver settings
Overlay drop-down list allows the user to select overlay. An overlay is one page document that can contain text and/or graphics, such as a business address and logo.
Edit Overlay Dialog allows users to enable or create overlays to print output.
Edit Overlay Dialog
2-2. Printer driver settings
Print Subset
2-2. Printer driver settings
Print Subset allows you to define which pages will be printed in what sequence. The default is Normal. You can select another Print Subset by selecting an appropriate choice in the Print Subset dropdown list. Your choices are:
- Normal (from first page to last page) - Reverse All Pages (from last page to first page) - Print Odd Pages (only odd numbered pages) - Print Even Pages (only even numbered pages)
Dark Text
2-3. Printer driver issues
- Have some problem in 1 dot horizontal line - Frequently appear this problem in Chinese windows (in DBCS character set, Simsun ) - Only text is darkened. - Some characters are not text. They are bitmap or line.
Overlap character in special OS (Thai windows…)
- Some problem in printing character in special OS- Use “print as graphic” of True-type option in graphic tab- Windows NT 4.0, 2000 and XP does not support “print as graphic” function.
In all OS, 5.0 or higher version of IE is needed
- Driver’s user interface module use commctl32.dll module of Microsoft - This module is installed after installing the IE5.0
Twai nTwai n
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
AgendaAgenda
I. What is TWAIN?II. TWAIN ArchitectureIII. How to work?IV. TWAIN Driver InterfaceV. Scan Resolution VI. Component Detail SpecificationVII. Troubleshooting
I. What is a TWAIN?
1. What is Twain?
1-1. Concept
TWAIN is Technology Without An Important Name
An image capture API and Protocol for Microsoft Windows , Apple Macintosh and Other operating systems.
The standard was first released in 1992, and is currently ratified at version 1.9 as of January 2000.
TWAIN is typically used as an interface between image processing software and a scanner or digital camera.
I. What is a TWAIN?
1. What is Twain?
1-1. Concept
The application software : An application must be modified to use TWAIN.
The Source Manager software: This software manages the interactions between the application and the Source.
The Data Source software: This software controls the image acquisition device and is written by the device developer to comply with TWAIN specifications.
II. TWAIN Architecture
2. TWAIN Architecture
2-1. Architecture Model
3. How to work?
3-1. The steps for scanning
III. How to work?
1. Place your image face down on the flatbed, or load the document face up in the Auto Document Feeder. Select the Document Source that will be used for scanning.
2. Preview the image or document scanned at lower resolution.3. Customize Scan Settings, which includes selecting Image Type, Resolution and
Document Type.4. Adjust Image Colors, including Brightness, Contrast, Gamma, Highlight and
Shadow. Try to change these values until the image looks best.5. Apply Filters to sharpen the image contours or retouch the image. You can also
descreen the images scanned from newspapers or magazines.6. Customize image view, which includes flipping and/or rotating the image if needed.7. Scan the image using the settings you defined8. Set the Scan Preferences to make the scanning parameters to be available the
next time you perform scanning. Save the customized settings as Favorites to use them when you scan documents or images next time.
ApplicationApplication Source ManagerSource Manager Data SourceData Source ScannerScanner
III. How to work?
IV. TWAIN Driver Interface
4. TWAIN Driver Interface
4-1. Main UI
Click!
It shows simple and user friendly UI To access the scan options, expand Options Panel.
RulesRules
ToolboxToolbox
PreviewPreview
InformationInformation
OptionsOptions
4. TWAIN Driver Interface
4-2. Scan Settings
Resolution: To set the resolution from 75 to 4800 DPI
IV. Samsung TWAIN Driver Interface
Image type: Specify the mode that will be used to scan the original image or document.
Text documents Lineart B/WText documents or drawings Halftone B/WBlack and white photos Gray 256 Scales Drawings, figures, schemes 256 Colors Color photos, posters, etc True Color (R,G,B)
Document Type : specify for document type define the limits of the area to be scanned.
Enlarge/Reduce : To reduce or enlarge the size of the resulting image. .
4. TWAIN Driver Interface
4-3. Adjustment
Shadow: To set the shadow level for the entire image.
IV. Samsung TWAIN Driver Interface
Brightness: To set the level of color brightness for the entire image.
Gamma : To set the gamma level for the entire image.
Auto : To make the TWAIN driver automatically adjust Brightness, Contrast, Highlight, Shadow and Gamma levels.
Contrast: To set the color contrast for the entire image.
Highlight: To set the color highlight level for the entire image.
Invert : To invert the image colors.
4. TWAIN Driver Interface
4-4. Filters
Sharpness: To sharpen your image and improve its clarity. With Sharpness you can make the finest details look more clearly.
IV. Samsung TWAIN Driver Interface
Blur : To soften and retouch your image or mask small defects like dots and spots.
Descreen : To minimize the appearance of unsightly interference patterns (moire patterns) which may occur in your image file when scanning original documents created by a halftone process.
Filters allow you to improve image quality by applying some visual effects.
4. TWAIN Driver Interface
4-5. Preferences
Document Source: display the device list selected to scan from
IV. Samsung TWAIN Driver Interface
Transparency: To adjust the TWAIN driver windows look
Auto : the document source is detected automatically.
Flatbed : Flatbed is selected as the document source.
ADF : Auto Document Feeder is selected as the document source.
4. TWAIN Driver Interface
4-6. About
IV. Samsung TWAIN Driver Interface
To view the information about this software.
5. Scan ResolutionResolution Color Gray B/W
24bit 8bit 8bi t Lineart Halftone
75(Draft) O △ O O O
100 O △ O O O
150 O △ O O O
200 O △ O O O
300(Normal) O △ O O O
400 △ △ △ △ △
500 △ △ △ △ △
600 O △ O O O
700 △ △ △ △ △
800 △ △ △ △ △
1000 △ △ △ △ △
1200(Best) △ △ △ △ △
1400 △ △ △ △ △
1800 △ △ △ △ △
2400 △ △ △ △ △
3000 △ △ △ △ △
3600 △ △ △ △ △
4200 △ △ △ △ △
4800(Maximum) △ △ △ △ △
O Support Optical Resolution ( 600* 1200 )
△ Support Software Enhance Resolution
X Not Support
V. Scan Resolution
Image Type - True Color (24bit), 256 Color, Gray(8bit), B/W Lineart and HalftoneResolution - Optical resolution : 75, 100, 150, 200, 300, 600 dpi - Enhance resolution : ~ 4800 dpi Document Source - Flatbed - ADF SimplexImage Area - English : Letter - Others : A4Unit - English: inch - Others : mmI/O Support - USB : (V1.1, V2.0) – USB 2.0 is recommended - Parallel ECP ModeOS - Win 98SE / ME - Win NT / 2K / XP / 2003
6. Component Detail Specification
VI. Component Detail Specification
If this should occur, try and reduce the total image size with the resolution setting.For example, if scanning an A4/Letter original in TrueColorRGB mode with an MS Office application, please set the resolution to 800dpi or less.
1. "An error has occurred while acquiring the image.“
VII. Troubleshooting
2. Twain driver does not work with Parallel mode
First of all, You must check the BIOS setting of PC which Parallel mode is “ECP” mode or not. Our Twain driver only supports “ECP”.
3. Twain driver does not work with USB in Windows NT
Windows doesn’t not support USB driver. So our Twain driver does not support USB mode in Windows NT
WI AWI A
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
AgendaAgenda
I. What is WIA?II. How to use?III. User InterfaceIV. Applications
I. What is a WIA?
1. What is WIA?
1-1. Concept
WI A i s Wi ndows I mage Acqui s i t i on
WI A i s pr opos ed by Mi cr os of t t o s uppor t t he i mage devi ces ( camer as , s canner s , …) .
WI A enabl es t he abi l i t y t o obt ai n pi ct ur es f r om camer as and s canner s , and t o eas i l y mani pul at e t hos e pi ct ur es wi t hout us i ng addi t i onal s of t war e.
WI A Dr i ver Suppor t s Mi cr os of t ® Wi ndows ® XP and USB onl y.
2. How to use?
2-1. The s t eps f or s canni ng wi t h Scanner s and Camer as Wi zar d
II. How to use?
1. Load the document(s) face up with top edge in first into the ADF or Place a single document face down on the scanner glass.
2. From the Start menu on your desktop window, select Settings, Control Panel and then Scanner and Cameras.
3. Double click your machine. The Scanner and Camera Wizard launches.4. Choose your scanning preferences and click Preview to see how your preferences
affect the picture.5. Enter a picture name, and select a file format and destination to save the picture.6. When the picture is successfully copied to your computer, you can choose to keep
working with the picture. Follow the on-screen instructions.
III. User Interface
3. WIA User Interface
3-1. Characteristics
It shows simple and user friendly UI
It shows the same UI independent of vendors and products.
FlatBed UI Document Feeder UI
III. User Interface
3-2. Default Option Paper Source If you want to scan with flatbed, select “Flatbed” If your want to scan with document feeder, select “Document Feeder”
Picture Type There are three type : Color, Grayscale, Black and white If you want the other option, select “Adjust the quality of the scanned picture” If you select “Adjust the quality of the scanned picture”, you can show “Advanced properties” dialog.
3-3. Advanced Properties Brightness and Contrast You can control the brightness and contrast of scan image. The range is 0 ~ 255(Default : 128).
Resolution(DPI) You can control the resolution of scan image. The range is dependent of the device capabilities(Default : 150 dpi).
III. User Interface
3-4. Duplex Scan Option ADF Duplex You can scan duplex by select this item.
III. User Interface(6x20 Only)
Long Edge Binding (Default) Select this item if you want to scan documents bound by long edge.
Short Edge Binding Select this item if you want to scan documents bound by short edge.
IV. Applications
4. Applications
4-1. Applications that don’t scan multi-pages. Microsoft Paint Microsoft Office XP
4-2. Applications that have latent bugs Lotus 1-2-3 : No gain the result when scan with document feeder Microsoft Office 2000 : The scanned image is some different with the size and color of original image.
Smar Thr u4Smar Thr u4
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
AgendaAgenda
I. What is SmarThru4? II. SmarThru4 ArchitectureIII. ImprovementsIV. How to work?V. FAQVI. Troubleshooting
I. What is SmarThru4?
ObjectivesObjectives
I. To make you aware of
SmarThru4
It is a Bundled Software package supplied with multi-functional peripherals (MFP).
It is for Scan, Copy, Print and Image Edit with MFP.
It is for Casual users with basic knowledge of computer and MFP operations. (So, It is Easy-to-Use and provides Powerful Utilizing MFP capabilities)
Scan To Image Edit Copy Print
I. What is SmarThru4?
I. What is SmarThru4?
System requirements are as follows:
Windows 98/Me/NT4.0- Processor: Pentium III 933MHz or more - Memory: 256MB or more- Free hard disk space: 500MB or more- Internet Explorer: 5.0 or higher
Windows 2000/XP - Processor: Pentium III 1.5GHz or more- Memory: 512MB or more- Free hard disk space: 500MB or more- Internet Explorer: 5.0 or higher
NOTE: For Windows NT 4.0/2000/XP, the system administrator
should install the software.
II. SmarThru4 Architecture
ObjectivesObjectives
I. To show you the
architecture of SmarThru4
MFP Cont r ol Panel UI
Scan t o pl ug i n( f r ame UI )
I mage pl ug i n( f r ame UI )
Copy pl ug i n( f r ame UI )
ScanUI
Scan toApplication
UI
Send toE- mail
UI
Send toFolder
UI
Send toOCR UI
Prescan UI
Scanengine
Applicationrunner
E- mailsender
FolderSaver
OCRwrapper
WebAlbum
UI
Send toWeb UI
Web up loader
StandardCopy
UI
QuickCopy
UI
Copy engine
Pr i nt pl ug i n( f r ame UI )
Special Print
UI
Print engine
Modules with UI
Modules without UI
Configuration manager
Image BrowseUI
Shared Shared componentcomponent
Image converterLead tools
(TIFF,JPEG,etc)PDF
II. SmarThru4 Architecture
ObjectivesObjectives
I. To show you the
improvements issues of
SmarThru4 compare with
SmarThru3
III. What’s Improvements?
UI is changed to improve usability. ST3 was too difficult to use.
By Usability Verification.
Several features are removed. ST3 was too bulky for general users.
Add the language in OCR(Chinese) ST3 did not support Chinese.
III. What’s Improvements?
Convenient COPY PC COPY firmware added.
Useful Image Conversion Convert BMP,JPEG,Single image TIFF to BMP,JPEG,Single image TIFF.
Merge the Multi-image to TIFF, ADF.
Web Album Samsung web server provided.
Special Print Various Image Album layout.
III. What’s Improvements?
ObjectivesObjectives
I. To show you the sequence
of Smarthru4
IV. How to Work?
Prescan means the rough scanning before main scanning job.
You can skip the Prescan and start Scan as a first step.
1. Scan To
IV. How to Work?
1. Scan To
Prescan the image.
Scanning the image and emailing it
Saving the scanned image file for several format(BMP,JPEG,TIF,PDF).
Performing text recognition with scanned image.
Uploading the scanned image to web site or ftp site.
3. Application3. Application
3. Email3. Email
3. Folder3. Folder
3. OCR3. OCR
3. Settings3. Settings
1. Prescan1. Prescan
2. Scan2. Scan
Selecting the image program to open the scanned image file.
IV. How to Work?
2. Image
Image Manager provide the several right mouse Functions.
(Open,Quick Print, Send to functions(Application,Email,Folder,Web,OCR),Cut,Copy,Delete)
The Images could be viewed by Thumbnails,Details,List.
IV. How to Work?
2. Image Editor
Image Editor provide the several Functions.
Edit ( Vertical Reflect, Horizontal Reflect, 90° degree CW, 90° degree CCW, Text, Crop, Image Size )
View ( Zoom+, Zoom-, Fit )
Adjust ( Redeye, Makeup, Mosaic, Level, Color, Effect )
IV. How to Work?
2. Image
Register Images to web server.
Settings the image managing job.
Manage the images. ImageImage ManagerManager
Web AlbumWeb Album
SettingsSettings
IV. How to Work?
3. Copy
Quick copy means simple copy with basic options.( 1 copy, 100% scale.)
Standard copy has several options which are frequently used.
In Settings menu, the user can set the special copies.
IV. How to Work?
3. Copy
Quick B&W , Color copy.
Copy Settings(number of ,Collate, Reduce/Enlarge,Paper Size, Paper Type, Mode,Contrast)
Special Print.(Auto Fit, Multiple Copies per side clone,Poster)
CopyCopy QuickQuick
StandardStandard
SettingsSettings
IV. How to Work?
4. Print
Quick Print provide the same menus in Image manager.
The user can make the their own album by using Special print .
IV. How to Work?
4. Print
Print the images.
Make the album with various layout.
PrintPrint Quick PrintQuick Print
Special PrintSpecial Print
IV. How to Work?
V. FAQ
In order to skip Pre-Scan process from SmarThru4
Go to Scan To-> Settings Tab -> Clear “Enable Prescan” option
How to send an image by email from SmarThru4
To send an image by e-mail, you must have a mail client program by default, like Outlook Express, which has been set up with your e-mail account.
VI. Troubleshooting
Condition : The scanner does not work.
Suggested solutions:
Check that the USB or parallel cable is connected properly.
Make sure that the USB or parallel cable is not defective.Switch the cable with a known good cable. If necessary, replace the cable.
ReviewReview
Mac Pr i nt erMac Pr i nt er
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
ObjectivesObjectives
I . Maci nt os h Pr i nt i ng
Sys t em
I I . Ei ger CUPS Dr i ver
I ns t al l / Uni ns t al l
I I I . To know what t he
f unct i ons ar e
s uppor t ed by Ei ger
CUPS Dr i ver
1. Introduction to Macintosh Printing
Sneaker Less than Mac OS X
Tioga Mac OS XWe supported once, currently does not use because of performance issue.
CUPS Common Unix Printing SystemMac OS X, beginning in version 10.2.4, uses the CUPS. But it is unstable. There is stable in Mac OS X 10.3.
1-1. Macintosh Printing System
Eiger driver provides PPD and Filter (The other modules are belongs to OS)
The filter generates printer data from raster Image made by the RIP
1-2. CUPS Architecture
PDF spool file
JobTicket
+
PPD
RIP
1-3. Macintosh Printer driver
PS Driver
ㆍUse the PS Driver on embedded OS.
ㆍPrinter driver Installer provides PPD dependent on Model
Raster Driver
ㆍRaster Driver cannot distinguish the text from Image.
ㆍRaster Driver change to the model-dependent command from image.
2. Eiger
Use the CUPS raster driver.
Support the Mac OS X 10.3 or later
Raster driver cannot distinguish between text and image.
Does not support an extra Font Pack.
2-1. Overview
I ns t al l Pr ogr am Execut i on
2-2. Pr i nt er Dr i ver I ns t al l
Follow the onscreen instructions. In the panel where you select the destination disk.( In most cases, it will be the only one available)
Next Phase : Choose ‘Easy Install’
You will be asked to provide a name and Password.
Use the name and password you specified (or use a name and password for another account on your computer that has administrator privileges)
Adding a Printer
Choose USB
Choose ‘SCX-4200 Series’
SCX-4200 driver automatically sets up printer. If the printer you want to use is not list, choose it in the ‘SCX-4200’ at Samsung folder.
Click Add.
Connect to your computer using a USB cable. After select ‘Add’ in Printer Setup Utility (Application/Utility), choose printer driver.
2-2. Pr i nt er Dr i ver I ns t al l
Default Printer Select ‘SCX-4200’ to your Printer List and choose a ‘Make Default’, then it becomes the default printer.
2-2. Pr i nt er Dr i ver I ns t al l
Deleting a Printer Driver in Printer List2-3. Pr i nt er Dr i ver Uni ns t al l
You can delete printer driver that it doesn’t appear in the Printer List. -> Select the ‘SCX-4200’ in Printer List and choose a ‘Delete’.
Printer Driver Uni ns t al l
Choose Uninstall at Install Program
★ Even if you uninstall the printer driver from Install Program, automatically printer is not deleted. - > Delete a printer by hand.
Page Setup2-4. Pr i nt er Dr i ver Set up
File-> Page Setup… Document has a default page setup that includes its paper size, orientation, and scaling.
New document create automatically formatted to fit a specific paper size. -> New paper size to be the default at any time from the “Save As Default”.
Print Setup (Copies & Pages) File-> Print… -> copies & Pages Copies Collated Copy Pages
2-4. Pr i nt er Dr i ver Set up
Print Setup (Layout) File-> Print…-> Layout Pages per Sheet - You can specify how many pages to print per sheet. The default is 1. The available options are: 1/2/4/6/9/16 Layout Orientation - Select the order and placement of the pages on the sheet. Border - To print border around each page on the sheet.
2-4. Pr i nt er Dr i ver Set up
Print Setup (Output Options) File-> Print…-> Output Options Save as File - You can save a document in Portable Document Format (PDF) or PostScript format. If PostScript, your document is saved as a PostScript Level 2 file in ASCII format.
2-4. Pr i nt er Dr i ver Set up
Print Setup (Scheduler) File-> Print…-> Scheduler - Now : The printer prints a job immediately. - At : The printer prints a job at the time you set in the field. - On Hold : The printer holds a print job in the print queue until you are ready to release it.
- Select a priority for your print job on the priority drop-down list.
2-4. Pr i nt er Dr i ver Set up
Print Setup (Paper Handling) File-> Print…-> Paper Handling All pages - (from the first page to the last) Odd numbered pages - (only odd numbered pages) Even numbered pages - (only even numbered pages) Reverse page order - (from the last page to the first)
2-4. Pr i nt er Dr i ver Set up
Print Setup (ColorSync) File-> Print…-> ColorSync ColorSync provides an easy way to ensure accurate color in your images. Quartz Filter - You can modify the images in your printed documents by adding a Quartz filter to your printer output.
2-4. Pr i nt er Dr i ver Set up
Print Setup (Paper Feed) File -> Print…-> Paper Feed The printer automatically selects the correct tray based on the paper size. - Auto Select automatically selects the correct Paper Source based on the Paper Size. - Manual selects the print manually from the Manual Tray.
2-4. Pr i nt er Dr i ver Set up
Print Setup (Paper Feed for first page) File -> Print…-> Paper Feed - You can select another paper source for first page.
2-4. Pr i nt er Dr i ver Set up
Print Setup (Paper Type) File-> Print…-> Printer Features -> Paper Type - Use the Paper Type drop-down list for selecting the type of paper loaded in the tray from which you want to print. - The default value is Printer Default. - Printer Default will rely on the engine's paper detection mechanism to sense
the paper type. .
2-4. Pr i nt er Dr i ver Set up
Print Setup (Resolution) File-> Print…-> Printer Features -> Resolution - Resolution defines the quality of the print output in simplest form: the number of dots per inch. - Resolutions available are 600 dpi (Normal) and 300 dpi (Draft). The default value is 600 dpi (Normal).
2-4. Pr i nt er Dr i ver Set up
Print Setup (Summary) File-> Print…-> Summary - The Summary tab displays a summary of selected features in other tabs.
2-4. Pr i nt er Dr i ver Set up
Run the Classic Application on Mac OS X 10.3
- Classic Application is do not executed on the Mac OS X 10.3. It is executed on Mac OS 9. - CUPS Driver doesn’t work on Mac OS 9.
-Our driver support Mac OS X 10.3 or later-Mac OS X 10.2 needs GostScript-After install the GostScript, the user can use our printer on Mac OS X 10.2 But, we can not guarantee.
If the user want to use our printer on Mac OS X 10.2
2-5. Printer driver issues
Pages per Sheet : 1 & Border printing.
-Only printing the border when Pages per Sheet is more than 2. -OS support this features.
Scheduler
- Real printing time is related on OS environment. - If you insert the time by keyboard, change the Priority, and then print the document, you’ll see that the time is changed to current time. OS bug, We reported it to the Apple.
Scale
-If you change the Scale and print some document at PowerPoint.-Some times you can see the following message.
Default paper size setting
- Macintosh does not have default paper size each printer.- How to set the default paper size : New paper size to be the default at any time from the “Save As Default”. Refer to ‘page setup’
Printing Jobs not disappeared in spooler at OS 10.3.2
-OS bug (OS 10.3.2)-Update to Mac OS 10.3.9 (Current version)
Mac TWAI NMac TWAI N
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
AgendaAgenda
I. What is TWAIN?II. TWAIN ArchitectureIII. How to work?IV. TWAIN Driver InterfaceV. Scan Resolution VI. Component Detail SpecificationVII. Troubleshooting
I. What is a TWAIN?
1. What is Twain?
1-1. Concept
TWAIN is Technology Without An Important Name
An image capture API and Protocol for Microsoft Windows , Apple Macintosh and Other operating systems.
The standard was first released in 1992, and is currently ratified at version 1.9 as of January 2000.
TWAIN is typically used as an interface between image processing software and a scanner or digital camera.
I. What is a TWAIN?
1. What is Twain?
1-1. Concept
The application software : An application must be modified to use TWAIN.
The Source Manager software: This software manages the interactions between the application and the Source.
The Data Source software: This software controls the image acquisition device and is written by the device developer to comply with TWAIN specifications.
II. TWAIN Architecture
2. TWAIN Architecture
2-1. Architecture Model
3. How to work?
3-1. The steps for scanning
III. How to work?
1. Place your image face down on the flatbed, or load the document face up in the Auto Document Feeder. Select the Document Source that will be used for scanning.
2. Preview the image or document scanned at lower resolution.3. Customize Scan Settings, which includes selecting Image Type, Resolution and
Document Type.4. Adjust Image Colors, including Brightness, Contrast, Gamma, Highlight and
Shadow. Try to change these values until the image looks best.5. Apply Filters to sharpen the image contours or retouch the image. You can also
descreen the images scanned from newspapers or magazines.6. Customize image view, which includes flipping and/or rotating the image if needed.7. Scan the image using the settings you defined8. Set the Scan Preferences to make the scanning parameters to be available the
next time you perform scanning. Save the customized settings as Favorites to use them when you scan documents or images next time.
ApplicationApplication Source ManagerSource Manager Data SourceData Source ScannerScanner
III. How to work?
IV. TWAIN Driver Interface
4. TWAIN Driver Interface
4-1. Main UI Pr evi ew Ar ea
Pr evi ew Ar ea
Cont r ol Ar ea
Cont r ol Ar ea
I nf or mat i on Ar ea
I nf or mat i on Ar ea
Click!
4. TWAIN Driver Interface
4-2. Scan Settings
Resolution: To set the resolution from 75 to 4800 DPI
IV. Samsung TWAIN Driver Interface
Image type: Specify the mode that will be used to scan the original image or document.
Text documents Lineart B/WText documents or drawings Halftone B/WBlack and white photos Gray 256 Scales Drawings, figures, schemes 256 Colors Color photos, posters, etc True Color (R,G,B)
Document Type : specify for document type define the limits of the area to be scanned.
Enlarge/Reduce : To reduce or enlarge the size of the resulting image. .
4. TWAIN Driver Interface
4-3. Adjustment
Shadow: To set the shadow level for the entire image.
IV. Samsung TWAIN Driver Interface
Brightness: To set the level of color brightness for the entire image.
Gamma : To set the gamma level for the entire image.
Auto : To make the TWAIN driver automatically adjust Brightness, Contrast, Highlight, Shadow and Gamma levels.
Contrast: To set the color contrast for the entire image.
Highlight: To set the color highlight level for the entire image.
Invert : To invert the image colors.
4. TWAIN Driver Interface
4-4. Filters
Sharpness: To sharpen your image and improve its clarity. With Sharpness you can make the finest details look more clearly.
IV. Samsung TWAIN Driver Interface
Blur : To soften and retouch your image or mask small defects like dots and spots.
Descreen : To minimize the appearance of unsightly interference patterns (moire patterns) which may occur in your image file when scanning original documents created by a halftone process.
Filters allow you to improve image quality by applying some visual effects.
4. TWAIN Driver Interface
4-5. Preferences
Document Source: display the device list selected to scan from
IV. Samsung TWAIN Driver Interface
Transparency: To adjust the TWAIN driver windows look
Auto : the document source is detected automatically.
Flatbed : Flatbed is selected as the document source.
ADF : Auto Document Feeder is selected as the document source.
4. TWAIN Driver Interface
4-6. About
IV. Samsung TWAIN Driver Interface
To view the information about this software.
5. Scan ResolutionResolution Color Gray B/W
24bit 8bit 8bi t Lineart Halftone
75(Draft) O △ O O O
100 O △ O O O
150 O △ O O O
200 O △ O O O
300(Normal) O △ O O O
400 △ △ △ △ △
500 △ △ △ △ △
600 O △ O O O
700 △ △ △ △ △
800 △ △ △ △ △
1000 △ △ △ △ △
1200(Best) △ △ △ △ △
1400 △ △ △ △ △
1800 △ △ △ △ △
2400 △ △ △ △ △
3000 △ △ △ △ △
3600 △ △ △ △ △
4200 △ △ △ △ △
4800(Maximum) △ △ △ △ △
O Support Optical Resolution ( 600* 1200 )
△ Support Software Enhance Resolution
X Not Support
V. Scan Resolution
Image Type - True Color (24bit), 256 Color, Gray(8bit), B/W Lineart and HalftoneResolution - Optical resolution : 75, 100, 150, 200, 300, 600 dpi - Enhance resolution : ~ 4800 dpi Document Source - Flatbed - ADF SimplexImage Area - Letter, A4, Statement, ETC - Default Image Area depend on OS System PreferenceUnit - Unit (cm, mm, inch, pixel, Point, Pica) - Default Unit depend on OS System PreferenceI/O Support - USB : (V1.1, V2.0) – USB 2.0 is recommendedOS - OS X (10.2, 10.3)
6. Component Detail Specification
VI. Component Detail Specification
VII. Troubleshooting
1. Twain driver does not work with Parallel mode
Macintosh Twain driver doesn’t not support Parallel I/O interface.
2. Twain driver does not work in OS Classic
Macintosh Twain driver doesn’t not support Mac OS 9.
Li nuxLi nux
SCX- 4200 Ser i esDr i ver
SCX- 4200 Ser i esDr i ver
Contents
1.Install2.Uninstall3.Using Configurator4.Scan Features5.Print Features6.Help System
1. Install1. Install
• Install• The user should login as root for installation.• When the CD is inserted, autorun will be executed on
the desktop.
• Install• After click Install button, welcome window is displayed.
1. Install1. Install
• Install• Progress bar shows the current status of installation.
1. Install1. Install
• Install• The following screen shows that installation was
successful.
1. Install1. Install
• Install• Now, MFP Configurator icon is displayed on the user’s
desktop.
1. Install1. Install
• Uninstall• To uninstall the driver package, the user need to
insert CD.
2. Uninstall2. Uninstall
• Uninstall• When the user selected Uninstall, the setup will
proceed uninstallation.
2. Uninstall2. Uninstall
• Uninstall• Progress bar below shows the status of uninstallation.
2. Uninstall2. Uninstall
• Uninstall• Now, all of the drivers are uninstalled.
2. Uninstall2. Uninstall
• Using Configurator• When the user executed MFP Configurator on the
desktop icon, the following window will be shown up.
3. Using Configurator3. Using Configurator
• Using Configurator– Manage printer queue
• The user can add / remove the printer queues and spooling jobs with Configurator.
– Manage ports• The user can check the status of parallel and USB
ports with Configurator.• The user can release the port so that it can be
available.
– Scan• The user can perform scan feature using Configurator.
– Test Print• The user can print a test page.
3. Using Configurator3. Using Configurator
• Using Configurator• When the user click “Test…”, the following menu will be
shown.• After click the “Start”, he will get a test page.
3. Using Configurator3. Using Configurator
• Using Configurator• When the port icon is clicked during the printing
process, Configurator will display that the current port is busy.
3. Using Configurator3. Using Configurator
• Using Configurator• While the port is busy, the scanner will not be able to
scan.
3. Using Configurator3. Using Configurator
• Using Configurator• In this case, you need to release the port in the port
module tab.• Otherwise, you can just wait a while until the port is
released.
3. Using Configurator3. Using Configurator
• Using Configurator• After the port is released, the scan feature is available
now.• If you click the “Properties…” button, the scan window
will be shown.
3. Using Configurator3. Using Configurator
• Scan Features• When the scanner properties window is executed, you
can select Preview and Scan function with appropriate properties.
4. Scan Features4. Scan Features
• Scan Features• After inserting a page in the document feeder and
clicking “Preview”, you can get the preview image on the right side.
4. Scan Features4. Scan Features
• Scan Features• You can use mouse pointer with dragging to select the
area where you want to scan. You may let the selected area as it is to scan the whole page.
4. Scan Features4. Scan Features
• Scan Features• If the scanning was successful, the Image Editor will
be executed automatically so that you can edit and save the scanned image.
4. Scan Features4. Scan Features
• Print Features• When you command lpr by clicking Print on most
application, the following UI will be shown up. You can select the printing options on it.
5. Print Features5. Print Features
• Print Features• By clicking “Properties…” button on the main window,
you can find the properties window. You can select more features on it. Each of the feature is described in the help.
5. Print Features5. Print Features
• Help System• If you click the “Help” button on each window, the
appropriate help will be shown on the help viewer.
6. Help System6. Help System
• Help System• You can also browse the topics when you click the
button below.
6. Help System6. Help System
Fi r mwar e( Sys t em s of t war e)
Fi r mwar e( Sys t em s of t war e)
SCX- 4200 Ser i esSCX- 4200 Ser i es
ContentsContents
I. Specification
II. Function
III. Maintenance
ⅠⅠ. Specification. Specification
Objectives
Understanding the specifications (Scanner, Copier, Printer) of SCX-4200 series. Comprehension of the feature of major elements.
ⅠⅠ. Specification. Specification
Item SCX- 4100 SCX - 4200
Compat i bi l i t y TWAI N s t andar d TWAI N s t andar d
Scan met hod Col or CI S Col or CI S
Scan r es ol ut i on 600 * 600 dpi ( opt i cal )
600 * 2400 dpi ( opt i cal )
Scan l engt h Maxi mum: 11. 7 i nches ( 297 mm)
Maxi mum: 11. 7 i nches ( 297 mm)
Scan wi dt h Maxi mum: 8. 5 i nches ( 216 mm)Ef f ect i ve: 8. 2 i nches ( 208 mm)
Maxi mum: 8. 5 i nches ( 216 mm)Ef f ect i ve: 8. 2 i nches ( 208 mm)
Col or bi t dept h 8bi t , 24bi t 8bi t , 24bi t
Mono bi t dept h 1bi t f or Text mode8bi t f or Gr ay mode
1bi t f or Text mode8bi t f or Gr ay mode
Scan s peed 27 s econds ( Li near t )72 s econds ( Gr ay Scal e)150 s econds ( Col or 300dpi )
15 s econds ( Li near t )30 s econds ( Gr ay Scal e)75 s econds ( Col or 300dpi )
Copy s peed Let t er : 15 copi es per mi nut eA4: 14 copi es per mi nut e
Let t er : 19 copi es per mi nut eA4: 18 copi es per mi nut e
Copy r es ol ut i on 600* 600 dpi 600* 600 dpi
Zoom r at e 50 ~ 200 % 50 ~ 200 %
Mul t i pl e copi es 99 pages 99 pages
Scanner and Copier Specifications
ⅠⅠ. Specification. SpecificationI t em SCX - 4100 SCX - 4200
Pr i nt met hod Las er Beam Pr i nt i ng Las er Beam Pr i nt i ng
Pr i nt s peed Let t er : 15 pages per mi nut eA4: 14 pages per mi nut e
Let t er : 19 pages per mi nut eA4: 18 pages per mi nut e
Paper s i ze Paper t r ay: Let t er , A4, Legal , Fol i o, A5, A6, B5Manual f eeder : Let t er , A4, Legal , Fol i o, Execut i ve, A5,B5, A6, Pos t Car d 4* 6, Envel ope Monar ch,Envel ope 10, Envel ope DL, Envel ope C5, Envel ope C6• Mi n. : 76 * 127 mm( 3* 5 i n. ) Max. : 216* 356 mm* ( 8. 5* 14 i n. )
Paper t r ay: Let t er , A4, Legal , Fol i o, A5, A6, B5Manual f eeder : Let t er , A4, Legal , Fol i o, Execut i ve, A5,B5, A6, Pos t Car d 4* 6, Envel ope Monar ch,Envel ope 10, Envel ope DL, Envel ope C5, Envel ope C6• Mi n. : 76 * 127 mm( 3* 5 i n. ) Max. : 216* 356 mm* ( 8. 5* 14 i n. )
Pr i nt r es ol ut i on 600* 600 dpi 600* 600 dpi
Emul at i on Compat i bl e wi t h USB 1. 1 Speci f i cat i ons and I EEE1284 Par al l el
Onl y USB 2. 0 Speci f i cat i ons
Compat i bi l i t y Wi ndows 98/ 2000/ NT 4. 0/ Me/ XPMaci nt os h 8. 6 ~ 9. 2 or 10. 1/ 10. 2/ 10. 3Li nux:• Redhat 7. 1 and above• Li nux Mandr ake 8. 0 and above• SuSE 7. 1 and above• Cal der a OpenLi nux 3. 1 and above• Tur bo Li nux 7. 0 and above• Sl ackwar e 8. 1 and above
Wi ndows 98/ 2000/ NT 4. 0/ Me/ XPMaci nt os h 10. 3/ 10. 4Li nux: ( vi a USB i nt er f ace onl y)• Redhat 8. 0 ~ 9. 0• Li nux Mandr ake 9. 0 ~ 10. 2• SuSE 8. 2 ~ 9. 2• Fedor a Cor e 1 ~ 3
Memor y 8MB 8MB
Fi r s t pr i nt i ng t i me
St andby mode: 12 s econds St andby mode: 12 s econds
Review
SCX-4200 gives the image acquisition ability by using of Color CIS module for copy, scan
SCX-4200’s scanner type is Flatbed.
ⅠⅠ. Specification. Specification
ⅡⅡ.. Function Function
Objectives
Understanding the User Interface
Comprehension of Functions
ⅡⅡ.. Function – User Interface Function – User Interface
ⅡⅡ.. Function – LED Function – LED
• Understanding the Status of LEDUnderstanding the Status of LED
The Status LED on the control panel shows the The Status LED on the control panel shows the status of your machine.status of your machine.
ⅡⅡ.. Function - Copy Function - Copy
Contents
1. Setting Options 2. Using Special Copy Features
ⅡⅡ.. Function - Copy Function - Copy
1. Setting Options
1. Reduce / Enlarge
2. Darkness ( Light / Normal / Dark )
3. Original Type (Text, Text/Photo, Photo)
4. Special Copy
5. Toner Save
6. Paper Setting
7. Copy Setup
8. Report
9. Machine Set up
10. Maintenance
ⅡⅡ.. Function - Copy Function - Copy
2. Using Special Copy Features
Clone Copying
Auto Fit Copying
2 sided in 1 page Copying
2-up Copying
Poster Copying
When user selects the photo mode (original type) in Legal and Folio size, it will be the Text/Photo mode.
ⅡⅡ.. Function - Copy Function - Copy
2.1. Clone Copying
- To provide the copies which are printed multiple original image.
- Edge Detection (To find edges of image by pre-scanning) - Image Shifting & Centering
ⅡⅡ.. Function - Copy Function - Copy
2.2. Auto Fit Copying
- To provide the paper-size copies
- Edge Detection (To find edges of image by pre-scanning) - Enlarge or Reduction (To fit for the paper)
: Restricted by Reduced/enlarged ratio ( 50 ~200 % )
ⅡⅡ.. Function - Copy Function - Copy
2.3. 2 sided in 1 page Copying
- To provide the copies which are printed both sides of ID card in a paper
- Half Scan Length & Not Reduction
2.4. 2-up Copying
- To provide the copies which are printed with 2-page documents.
- Image Reduction
- RotationIf paper size is larger than A4, paper size sets “Letter”.
ⅡⅡ.. Function - Copy Function - Copy
2.5. Poster Copying
- To provide the copies which are printed partial and enlarged image.
- Partition (3 by 3) - Enlargement
ⅡⅡ.. Function - Copy Function - Copy
Your machine offers two ways to scan:
From the Samsung SmarThru software: Launch Samsung SmarThru and open the Scan Wizard to begin scanning.
From TWAIN-compliant software: You can use other software including Adobe Photo Deluxe and Adobe Photoshop.
NOTES:
To scan with your machine, you must install the MFP driver.
Scanning is done through the same LPT or USB port currently assigned for your printer port.
ⅡⅡ.. Function - Scan Function - Scan
ⅡⅡ.. Function - Print Function - Print
NOTES:
To print with your machine, you must install the MFP driver.
Printing is done through the LPT or USB port.
Your machine uses QPDL (emulation)
Printer Resolution is 600*600 dpi
ⅡⅡ.. Function Function
Review
What kinds of special copy function do Eiger have?
What is the special copy function to provide the copies which are printed with 2-page documents?
What is the emulation for printing?
ⅢⅢ .. Maintenance Maintenance
Contents
1. Printing the System Data List2. Clearing Settings 3. Cleaning the Drum4. Tech mode5. Detecting Home position
1. Printing the System Data List
Your machine can print the system data report shows the status of the user-selectable options. You may print this list to confirm your changes after changing any settings.
ⅢⅢ .. Maintenance Maintenance
2. Clearing Settings
You can selectively clear information stored in your machine’s memory.
3. Cleaning the Drum
If there are streaks or spots on your print, You can clear the OPC drum of the cartridge.
4. Tech mode => This information contained herein is for reference use only
- Mode Change : Menu - Copies - Left - Right - Menu – Right
- Data Setup : Value Setting that is not in User Mode
- Machine Test : Checking the Machine state
- Report : Information about set state
ⅢⅢ .. Maintenance Maintenance
• In tech mode, the technician can check the machine and perform various test to isolate the cause of a malfunction
4.1. Tech mode – Data Setup
- Clear All Memory : Return to the factory default value - Clear Count ( Total Page Counts, Platen Scan Counts ) - Flash Upgrade : (Local/Remote)
4.2. Tech mode – Machine Test
- Switch Test : Test keys for user interface - Dram Test : Check the Dram condition - Rom Test : Show the version of Flash and Engine - Pattern Test : Print the defined patterns - Shading Test : Get the new shading profile by the shading Test
4.3. Tech mode – Report
- System Data : The setting values in menu - Error Info :The error state (ex Paper JAM-0 , LSU Error etc)
ⅢⅢ .. MaintenanceMaintenance
4.2 Machine Test
ⅢⅢ .. Maintenance Maintenance
4.2.1. Switch test
I t can exami ne t he oper at i on s t at us of each Keys / But t ons on Cont r ol Panel .Us e t hi s f eat ur e t o t es t al l keys on t he oper at i on cont r ol panel . The r es ul t i s di s pl ayed on t hewi ndow LCD wi ndow each t i me you pr es s a key
4.2.2. Dram test I t can exami ne t he DRAM whi ch i s mount ed i n Mai n PBA or Ext ens i on DI MM.Us e t hi s f eat ur e t o t es t t he machi ne' s DRAM. The r es ul t appear s i n t he LCD di s pl ay.I f al l memor y i s wor ki ng nor mal l y, t he LCD s hows << O K >>
4.2.3. Rom test Us e t hi s f eat ur e t o t es t t he machi ne' s ROM. The r es ul t and t he s of t war e ver s i onappear i n t he LCD di s pl ay.
• FLASH VER : 1. 00 V • ENGI NE VER : 1. 00V
4.2 Machine Test
ⅢⅢ .. Maintenance Maintenance
4.2.4. Pattern test
I t i s t he f unct i on t hat pr i nt s t he I mage Fi l es embedded i n Ei ger f or PQ exami nat i onUs i ng t hi s pat t er n pr i nt out , you can check i f t he pr i nt er mechani s m i s f unct i oni ng pr oper l y.
I t i s needed i n t he pr oduct i on pr ogr es s . Ser vi ce per s on does n' t need t o us e i t
4.2.5. Shading test
The machi ne pr i nt s t he r epor t of Scanner s t at us bes i des Scanner Cal i br at i on f unct i on i nSys t em Admi n Tool s .
I f t he copy i mage qual i t y i s uns at i s f i ed, per f or m t he f unct i on t o check t he condi t i on of t he pr i nt out f or checki ng whet her or not havi ng Scanner t r oubl e.
5. Detecting Home position
ⅢⅢ .. Maintenance Maintenance
When the Scan job start, it needs a position for starting to scan. This position bases on the Home Position.
Other Models : Home Sensor Eiger : S/W algorithm (Check whether scanned data are same with the attached special pattern. )
It needs in two cases as below.
- When Power is on- Whenever Image sensor is returned
In Error : Display “SCANNER ERROR” on the LCD
Check point : Check lamp and cable condition : Check Motor condition
Har dwar eHar dwar e
SCX- 4200 Ser i esSCX- 4200 Ser i es
AgendaAgenda
Ⅰ. Introduction
Ⅱ. Main PBA
Ⅲ. OPE PBA
Ⅳ. SMPS PBA
Ⅰ. General Specification
ObjectivesObjectives
I. To make you aware of the
key specification points
II. To show you how SCX-4200
series are different
Ⅰ. Introduction
Main BoardSMPS + HVPS
Panel Board
OPC
1-1. Overview
Ⅰ. Introduction
1-2. Block Diagram
Chr ous 2
CY25811
FLASHROM29LV800
SDRAM8MB
Motor Drv.A3977
Motor Drv.A3977
RESET IC
SMPSHVPS
REG
REG
ExitSensor
Feed Sensor
CoverOpen S/W
24V/5VThermistor
Fus er
LSU
OPE
HC 48C50
LCD
KEY
PC
Pi ckupSol enoi d
FAN 2
ScannerA(1:20)
D(0:15)
5V
3.3V
1.8V
Mai n Boar d
P/EmptySensor
Engi ne Fr ame
Devel oper Uni t
CY25814
3.3V
MPSensor
CDRH S/ W
MPSol enoi d
LED
USB2.0
Main CLK10.00MHz
Video CLK16.59MHz
UART
CR
DR
SR
TR
MainMotor
ScanMotor
Thermostat
TRIAC
FAN 1
LSU
CIS
Ⅰ. Introduction
1-3. Connection Diagram
Ⅰ. Introduction
1-4. General Spec.
Ⅰ. Introduction
1-4. General Spec.
I t em SCX- 4100 SCX- 4200 ETC
Mai n CPU Same (Chorus 2)
ROM Same (1MB)
RAM Same (8MB)
Vi deo Cl ock 12.99MHz 16.59MHz
USB USB 1.1 USB 2.0
Mai n- Mot or 2K (Bi- Polar) 2NK (Bi- polar)
Mot or - I C AN44060 A3977
Heat - Lamp Same (600W)
LSU Same
Fan Main(1) Main(1) + Sub(1)
Scan CI S Canon 600dpi LITEON 600dpi
Scan- Mot or Uni- Polar(35Φ) Bi- Polar(35Φ)
Mot or - I C STA403A(Uni- Polar) A3977 (Bi- polar)
Panel LCD 2*16 , 7Keys 2*16 , 8Keys , 1LED
ASI C 9228(SEC) 48C05(Holtec)
SMPS/ HVPS
SMPS Same SMPS/HVPS on 1 Board- >Heat Sink Added
HVPS Same
1-5. Comparison Between SCX-4100 and SCX-4200
Ⅱ. Main PBA
ObjectivesObjectives
I. To show you the structure
and key elements of Main
PBA in SCX-4200
1 32 4 15 67 8
Ⅱ. Main PBA
2-1. General description
Main PBA employs Chorus2 as an ASIC, which is developed for LBP Printer
10 11 12 135 17 18 191416
20 219 7
Ⅱ. Main PBA
2-1. General description
1 LSU CONNECTOR (CN5) 12 MAIN CLUTCH CONNECTOR3 (CN2)
2 MAIN MOTOR DRIVER IC –A3977(U12) 13 FLASH ROM- 29LV800 (U4)
3 MAIN MOTOR CONNECOR (CN10) 14 SDRAM - K4S641623H- TL75 (U2)
4 PTL CONNECTOR (CN9) 15 CIS CONNECTOR (CN8)
5 SCAN MOTOR DRIVER IC –A3977 (U6) 16 GRAPHIC PROCESSOR ASIC- CHORUS2 (U5)
6 SCAN MOTOR CONNECTOR (CN13) 17 MAIN CLOCK CRYSTAL- 10.00 MHz (OSC3)
7 THERMISTOR CONNECTOR (CN12) 18 VIDEO CLOCK CRYSTAL - 16.59MHz (OSC2)
8 USB 2.0 (CN6) 19 USB CLOCK CRYSTAL – 12MHz (OSC1)
9 CRUM CONNECTOR (CN11) 20 OPE CONNECTOR (CN14)
10 ENGINE CONNECTOER (CN4) 21 FAN2 (CN7)
11 MP CLUTCH CONNECTOR (CN3)
CPU Core Clock Bus Package features
Jupiter 4e
SPGPm
SPGPv3
Chorus 2
Chorus m
PPC 266
RM7000Se
ARM 9 150 ㎒ 16 bit QFP Internal Flash 0.5MB
ARM 9 166 ㎒ 16 bit BGA RAM 32bit Control
ARM 10 400 ㎒ 32 bit BGA DDR Memory supporting
ARM 7 66 ㎒ 16 bit QFP Internal CIP
MIPS 460 ㎒ ~ 64 bit BGA CPU
PPC 266 ㎒ 32 bit QFP CPU
ARM 9 300 ㎒ 32 bit BGA Internal CIP
2-2. LBP CPU Serises
Ⅱ. Main PBA
2-3. Chorus2 Samsung's S3C46Q0X 16/32-bit RISC micro controller is designed to provide a cost-effective, low power, small die size and high performance micro-controller solution for inkjet, laser beam printer and MFP.
The S3C46Q0X is developed using ARM7TDMI core, 0.18m CMOS standard cell, and memory cell.
The integrated on-chip functions are as follows:
- 1.8V internal, 3.3V external (I/O boundary) microprocessor with 4KByte Cache- Image Processor- On-chip clock generator with PLL- Memory & External Bank Control- DMA Control (5-channel)- Interrupt Control- 2-port USB Host /1- port USB Device (ver 2.0) Interface Control- UART (2 Channel)- Synchronous Serial Interface Control-Timer (4 Channel)- Watch Dog Timer- Power control: Normal, Slow, Idle, Stop and SL_IDLE mode- A/D Converter (10-bit, 2 Channel)- General I/O Port Control- Print Head Control- Carrier Motor Control- Paper Motor Control- Tone Generator- RTC with calendar function- S/W Assistant function( Rotator )
Ⅱ. Main PBA
2-3. CPU (Chorus2)Block diagram
Ⅱ. Main PBA
2-4 Flash Memory (as ROM) : AM29LV800 Storing the systems program and downloading the system program through the PC interface.
Capacity : 1 Mega Byte.
AM29LV800
Access Time : 70 nsec
Circuit Diagram of Flash Memory
Ⅱ. Main PBA2-5. SDRAM Used as a buffer, system working memory area, etc, while printing
Capacity : 8 Mbyte ( K4S641632H-TL75)
Access Time : 133 MHz
Circuit Diagram of SDRAM
Ⅱ. Main PBA
2-6. Main motor Driver Using A3977 as Motor Drive By gearing the main motor drives the rollers such as feeding roller, developing roller, fuser roller, and distributing roller. The step motor is controlled for the sections, acceleration section and fixed speed section. In the initial stage of the motor run, appoint the acceleration section to prevent the isolation of the motor. It is controlled by the AN44060 motor drive IC. The step signal and the enable signal are sent to make the phase for driving the motor in CPU.
Us es PHI LI PS I SP1582BS I C
■Complies fully with: - Universal Serial Bus Specification Rev. 2.0 - Most Device Class specifications - ACP, OnNow and USB power management requirements. ■Supports data transfer at high- speed (480 Mbit/s) and full- speed (12 Mbit/s) ■High performance USB peripheral controller with integrated Serial Interface Engine (SIE), Parallel
Interface Engine (PIE), FIFO memory and data transceiver ■Automatic Hi- Speed USB mode detection and Original USB fall- back mode ■Supports sharing mode ■Supports I/O voltage range of 1.65 V to 3.6 V ■Supports VBUS sensing ■High- speed DMA interface ■Fully autonomous and multi- configuration DMA operation ■7 IN endpoints, 7 OUT endpoints and a fixed control IN/OUT endpoint ■Integrated physical 8 kbytes of multiconfiguration FIFO memory ■Endpoints with double buffering to increase throughput and ease real- time data transfer ■Bus- independent interface with most microcontrollers and microprocessors ■12 MHz crystal oscillator with integrated PLL for low EMI ■Software- controlled connection to the USB bus (SoftConnect) ■Low- power consumption in operation and power- down modes; suitable for use in bus- powered USB
devices
2-7. USB INTERFACE
Ⅱ. Main PBA
2-8. CIS
CIS Module radiates the light by LED to the document, then according to LED, the reflection signals are divided with R,G,B data. The RGB data (analog signal) convert into digital signal through ADC ,then the digital signal is transmitted to Chorus2 Image Processor Block.
Object
Image Sensing
Transfer
Signal Receiving
Processing…DisplayPrintingEtc
Image Sensor
Light Source Image Scanning Process
Structure of CIS
N
Rod Lens
Shift Register
Vout
Circuits Timing Diagram
N
Rod Lens
Shift Register
Vout
LED Timing for Color Reading
1. Per 3 Col or per St or age Ti me 2. Onl y Gr een LED ON
LED Timing for Mono Chrome Reading
Ⅲ. OPE PBA
3-1. General description
OPE board is consisted of various function keys and LCD to display an operation of key.OP micom(48C05) is 8-bit micro controller device designed for multiple I/O control. It creates a panel circuit with LCD and other devices. A communication method with a CPU of a main board is UART( TXD-transmit, RXD-receive).
Menu This is to be used to enter the Menu
Copi es 1-99
OK This key is used to select the right item what customer wants from several items.
Start This key is used to activate the job
Stop This key is used to stop the job being done or to exit from the Menu.
Back This key is used to move previous menu – upper level
◀/▶ Left/Right Arrow Key
Menu OK Back Copies Stop Start ◀ ▶
Ⅲ. OPE PBA
3-2. UART ■ OPE and main board exchange information by UART. The band rate is 9600bps, and uses 7.37 MHz resonator as oscillating element. It engages in communication with 8 bit data without parity bit. UART has two lines for Tx and Rx. The default level is in the 'high' state. For communication, the start bit (low level) is transmitted before the data. When the data transmission is completed, the high state is maintained as the stop bit is transmitted.
■ UART TX format :Codes for change of keys are transmitted in single code, and OK or error message to check if communication is performed properly are also transmitted in single code.
■ UART RX format: : Data being received will be arranged to be received as according to the following specified format to know what data they are.
Main Controller
MicroProcessor
FUSER
HVPS
INTERFACE
LSU
OPCDev.
Supply
Cha.
Clean
SMPS (Switched Mode Power Supply)To Supply Constant & Stable DC PowerTo Supply DC Bias VoltageTo Control Total System Operation
AC to DC and then DC to DC Conversion
1. The Role of SMPS & HVPS
IV . SMPS & HVPS PBA
4-2. SMPS & HVPS Spec.
SMPS is the power source of entire system. It is assembled by an independent module and completely common use with SCX-4200 and it is same characteristic with SCX-4100. It is mounted at the bottom of the set.The SMPS supplies the DC power for driving the system, and the AC heater control part, which supplies the power to fuser. it has two output channels. Which are +5V and +24V.
SMPS( Switching Mode Power Supply ) HVPS (High Voltage Power Supply )
HVPS creates the high voltage of THV/MHV/Supply/Dev and supplies it to the developer part for making best condition to display the image. The HVPS part takes the 24V and outputs the high voltage for THV/MHV/BIAS, and the outputted high voltage is supplied to the toner, OPC cartridge, and transfer roller.
IV . SMPS & HVPS PBA
4-3. SMPS & HVPS Spec.1) Tr ans f er Hi gh Vol t age( THV+) - I nput Vol t age: 24 V DC ±15% - Out put Vol t age: MAX +5. 0KV ± 5%( Dut y Var i abl e, no l oadi ng) - 1. 0KV ± 15%( when cl ear i ng, 200Mohm) - Out put Vol t age Tr i gger : 6. 5 µA - I nput cont r as t of t he Vol t age s t abi l i t y degr ee under ± 5%
( f l uct uat i ng i nput 21. 6V~26. 4V) Loadi ng cont r as t : ±5% or l es s - Out put Vol t age Ri s e Ti me : 100ms Max - Out put Vol t age Fal l Ti me : 100ms Max - Tr ans f er vol t age r ange as envi r onment var i abl e : +650V( Dut y 90%)
~5KV( Dut y 10%) - Envi r onment Recogni t i on Cont r ol Met hod : The THV- PWM ACTI VE
t r ans f er s act i ve s i gnal . I t det ect s t he r es i s t ance by r ecogni zi ng t he vol t age
val ue, F/ B, whi l e per mi t s t he envi r onment al r ecogni t i on vol t age. - Out put Vol t age Cont r ol Met hod : Tr ans f er Out put Vol t age i s out put
and cont r ol l ed by changi ng t he Dut y cycl e of t he THV PWM Si gnal . 90% Dut y: +650V,
10% Dut y: +5KV ± 5%
2) Char ge Vol t age( MHV) - I nput Vol t age: 24 V DC ±15% - Out put Vol t age: - 1. 3KV ~ - 1. 8KV DC ±50V - Out put Vol t age Ri s e Ti me : 50ms Max
IV . SMPS & HVPS PBA
4-4. SMPS & HVPS Spec. - Out put Vol t age Fal l Ti me : 50ms Max - Out put Loadi ng Range : 30M ohm ~1000M ohm - Out put Cont r ol Si gnal ( MHV- PWM) : CPU i s HV out put when PWM i s LOW
3) Cl ear i ng Vol t age( THV- ) - The( +) Tr ans f er Vol t age i s not out put becaus e t he THV PWM i s cont r ol l ed wi t h hi gh. - The( - ) Tr ans f er Vol t age i s out put becaus e t he THV – Enabl e Si gnal i s cont r ol l ed wi t h l ow. - The out put f l uct uat i on r ange i s bi g becaus e t her e i s no Feedback cont r ol .
4) Devel opi ng Vol t age( DEV) - I nput Vol t age: 24 V DC ±15% - Out put Vol t age: - 200V~600V DC ±20V - Out put Vol t age Fl uct uat i on r ange: PWM Cont r ol - I nput cont r as t of t he out put s t abi l i t y degr ee ± 5% or l es s Loadi ng cont r as t : ±5% or l es s - Out put Vol t age Ri s e Ti me : 50ms Max - Out put Vol t age Fal l Ti me : 50ms Max - Out put Loadi ng r ange : 10M ohm ~1000M ohm - Out put Cont r ol Si gnal ( BI AS- PWM) : t he CPU out put i s HV out put when PWM i s l ow.
5) Suppl y - Out put Vol t age: - 400V ~ 800V DC±50V( ZENER us i ng, DEV) - I nput cont r as t of t he out put s t abi l i t y degr ee under ±5%
Mechani s mMechani s m
SCX- 4200 Ser i esSCX- 4200 Ser i es
I. General Specification
II. Process
III. Disassembly
IV. Troubleshooting
AgendaAgenda
Ⅰ. General Specification
Ⅰ. Understanding the General specifications of SCX-4200 series
Ⅱ. Comprehension of the feature of major elements
ObjectivesObjectives
Ⅰ. General Specification
Model Name SCX-4200Functions Printer,Copier,Scanner
409 *362 * 232(mm)8.7kg12.2kg16*2 Graphic"USB 2.0"500
Printing 4,000Scan to Copy 800
5years/50,000PagesYes"AC110V~127V, 220V ~ 240V"Energy Star Compliant53dBA38dBA53dBA
EMI Approval Class BYes (5/10/15/30/45min.off)LaserNo18ppm/19ppm(A4/Letter)
Resolution Normal 600*600dpiRET No
Items
General
Size (W*D*H)Weight with accessoriesWeight with PackageLCDInterface
Engine Life
Max Duty Cycle
AMV(Average Month Volume)
Power Switch
Input VoltagePowerConsumption
Power Sleep Mode
NoiseOperatingStandbyPrintingEMI Approval
PC Print Power Save ModePrint MethodN/W I/fSpeed (Engine)
Ⅰ. General Specification
SPLYes
Fpot Stand by Approx. 11 secondsPower Save Less than 53 seconds
208 x 273 mm (Letter)-256levelColor CIS
Line,Halftone 15secGray 30secColor 75secOptical 600x2,400dpiEnhanced 4,800x4,800dpi(USB)
256levelMax 216mmEffective 208mm
Scan Length Max 297mm18cpm/19cpm(A4/Letter)
Copy Quality Selection Text 600x300dpior Original Image type Text/Photo 600x300dpiselection Mode Photo 600x600dpi
Stand by approx : 11secFrom Cold Start Less than 53 sec
Speed
Copy
FCOT
Scan
HalftoneScan MethodScan Speed (Second/scan) 300dpi
Halftone
Resolution(Optical)
Scan Width
PC Print
Print LanguageToner Save
Printable AreaDuplex Print
Ⅰ. General Specification
Copy Speed SDMC 18ppm/19ppm(A4/Letter)50-200%1~99
Darkness Control 3 level Light, Normal, DarkCopy Mode(=Original) Text, Text/Photo, PhotoAuto return to defaultmode Yes( after 1 minute) Time can be changeable:
15,30,60,180 sec, off2-up Copy YesAutoFit Copy Yes2 Side in 1 pg Yes(ex. ID Card Copy)Clone YesPoster Yes
CassetteMain Tray 250Sheets/20lb(75gr)Bypass 1sheet
NoFace Down 50 sheets/20lb(Plain Paper)Face Up 1 Sheet
Face down /Face up
Main Tray Legal,A4,Letter,FolioExecutive,B5,A5,A6
Bypass Envelope6 3/4, 7 3/4,#9,#10DL,C5,B5
Copy
Type
Input Capacity
Paper Handling
Zoom RangeMulti Copy
Special Copy
Optional Cassette
Output Capacity
Output Control
Paper Type
Ⅰ. General Specification
Main Tray 16 ~ 24 Ib(60gr ~ 90gr)Bypass 16 ~ 32 IbStandard output Bottom to Top Front(FIFO)Straight Through Face up/Single SheetMax 216*356mm(5.8"*14")Min 76*127mm(3"*5")DOS NoWin 3.x NoWin 95 NoWin 98&WinME YesWin NT 4.0 NoWin 2000 YesWin XP YesMac Yes(Mac Printer,Twain)Linux Yes(Print,Scan)
WHQL Printer,WIA Yes(WinXP only)Printer SPLTWAIN YesWIA Yes
RCPNo (Remote Control Panel,Only web services for upgradeFW)
PC-FAX No(Only available through PC)
Driver
Software
Paper Path
Paper Size
OS Compatibility
Paper Handling
Media Weight
Ⅰ. General Specification
Offset BoxYesYesYes(Electronic)
S/W CD ROM 1CD for user manual SmarThru4,Print Driver,ScanDriver
Toner Cartridge Yes 1 eaPower Cable Yes 1 ea(L-shape power cable)Printer Cable No China,Korea,Russia : USBType One Piece
Front Door open and frontloading
Initial 1K PagesRunning 3K Pages
Toner Count Level Sensor No(Dot Counter)Minimum Specification Pentium-II 233MHz
64MB RAM120MB Free disk space
PC Interface USB 2.0(Without HUB mode)50,000 Pages50,000 Pages50,000 Pages50,000 Pages
PeriodicReplacing Parts
Pickup RollerTransfer RollerSeparation PadFuser Unit
Owner's manual
Accessory
Package & POP
Consumables
How to install
Toner Life
POPQIG
Package
PC Specification
Ⅰ. General Specification
Ⅰ. SCX-4200 gives the image acquisition ability by using of Color CIS module for copy and scan.
Ⅱ. Is there the function of PC scan in SCX-4200?
Ⅲ. Printing Specification of SCX-4200 is equal to ML-15x0, ML-17x0, and SCX-4x16, SF-565P
ReviewReview
Ⅰ. Understanding the basic structures and operating principle of each parts (Engine Part, Scanner Part) Ⅱ. Studying the printing process and electronic photo process Ⅲ. Comprehension of System Layout
ObjectivesObjectives
Ⅱ. Process
Ⅱ. Process
A. Engine Part
B. Scanner Part
Ⅱ. Process
L S U
Toner Cartridge
1
2
3
5
6
78
Fuser
1 Paper Input (Cassette)
2 Paper Input (Manual Feeder)
3 Paper Out (Face Down)
4
Paper Empty Sensor (Manual)5
Paper Empty Sensor (Cassette)6
Paper Feeding Sensor7
Paper Exit Sensor
4
8Paper Out (Face Up)
A. Engine Part
Ⅱ. Process
1. Printing Process
PC
ORIGINAL DOCUMENT
DRIVERCONVERT TO THE PRINTER LANGUAGE
ELECTRICAL SIGNAL
CONNECTIVITYCONTROLLER
CONVERT TO THE BITMAP IMAGE
1.CHARGING 3.DEVELOPMENT2.EXPOSURE
4.TRANSFER5.FIXING
RECOVERY TO THE ORIGINAL IMAGE
LSU
2. Electronic Photo Process
Ⅱ. Process
3. System Layout3-1. Feeding Section
Feeding Method : Universal Cassette Type Feeding Standard : Center Loading Feeding Capacity : Cassette 250 Sheets(75g/ ㎡, 20lb Paper Standard) Manual 1 Sheet(Paper, OHP, Envelope, etc.) Paper Detecting Sensor : Photo Sensor Paper Size Sensor : None Sheet-Guide paper, Sheet-Sub Cassette
Ⅱ. Process
3. System Layout3-2. Transfer Ass’y
Li f e Span : Pr i nt over 50, 000 Sheet s ( i n 15~30℃)
Ⅱ. Process
3. System Layout3-3. Driver Ass’y
By driving the motor, it supplies power to the feeding unit, the fusing unit, and the distributing unit. In SCX-4200 Series, Latch Gear is used for an easy Jam Removal at Gear Drv Fuser
Ⅱ. Process
3. System Layout3-4. Fuser Ass’y
Ⅱ. Process
Halogen Lamp - Control the Fusing Temperature by Heating (Receptacle type) Thermostat - Temperature Intercepting Device, Open 170°c (Receptacle type) Heat Roller - Teflon Coating, Same as ones of Snipe (ML-2010) Pressure Roller - Silicon, Same as ones of Snipe (ML-2010) Thermistor - Temperature Detecting Sensor
3. System Layout3-5. LSU(Laser Scanner Unit)
Ⅱ. Process
3. System Layout3-6. Toner Cartridge
Developing Method : Non-magnetic 1 element contacting method Toner : Non-magnetic 1 element shatter type toner Toner remaining amount detecting sensor : None The life span of toner : 3,000 Sheets(IDC Pattern/A4 Standard) OPC Cleaning : Collect the toner by using electric static + FILM OPC Management of disused toner : Collect the toner by using electric static (Non-Cleaner type) OPC Drum protecting Shutter : None
Ⅱ. Process
Ⅱ. Process
Scan Method : 600dpi Color CIS Module
Maximum Scan Width : 216 mm (width of Letter Size)
Effective Scan Length : 297 mm
Scan Line Time : 1.637 msec(mono)
SCAN LOWER
TIMING BELT
SLIDER-CIS
CIS
MOTOR ASS’Y
COVER PANEL
SHAFT CIS
B. Scanner Part
1. Layout
Ⅱ. Process
2. Panel Functions
Ⅰ. What is the function of paper feeding sensor in Engine part? Ⅱ. Do you know life of Transfer Roller? Ⅲ. Do you know the function of Thermistor and Thermostat?
ReviewReview
Ⅱ. Process
Ⅲ. Disassembly
Ⅰ. Studying the method of disassemble parts from a complete whole Ⅱ. Comprehension of the function of each parts
Ⅲ. Understanding the basic structures of major part (Engine, Scanner).
ObjectivesObjectives
Let’s see a ‘Flash’ Manual
Ⅲ. Disassembly
Ⅲ. Disassembly
Ⅰ. To separate the Scan Unit (Scan Assembly), What is should you do?
Ⅱ. Can you understand the operating method of Scan Unit?
ReviewReview
Ⅰ. Building ability to deal with various problems raised in the field by reviewing troubleshooting Ⅱ. Check the solution of each problem. Ⅲ. Check the difference of each Jam.
ObjectivesObjectives
Ⅳ. Troubleshooting
1. Paper Jams
Ⅳ. Troubleshooting
1. Paper Jams1-1. Paper Jam0
Ⅳ. Troubleshooting
1. Paper Jams1-2. Paper Jam1
Ⅳ. Troubleshooting
Check and Cause Solution
1. If the recording paper is jammed in
front of or inside the fuser.
2. If the recording paper is stuck in
the Fuser just after passing through
the Actuator Feed, Feed Actuator
may be defective.
1. Replace the SMPS.
2. Reassemble the Actuator- Feed
and Spring- Actuator if the return is bad.
1. Paper Jams1-3. Paper Jam2
Ⅳ. Troubleshooting
2. Paper Multi-feeding
Ⅳ. Troubleshooting
3. Copy Problems3-1. Abnormal noise
Ⅳ. Troubleshooting
•Description There is noise from the Platen when copying
Check and Cause Solution1. Check the Scanner Motor and gear.
2. Check the Motor Driver on Driver PBA.
1. Check for correct assembly of gear and motor.
Ensure no parts are fouling and there are no foreign
objects in the mechanism or scanner path. Replace
any worn parts.
2. Replace the main PBA.
3. Copy Problems3-2. Defective Image Quality
Ⅳ. Troubleshooting
3. Copy Problems3-3. Multi Feeding
Ⅳ. Troubleshooting
4. Printing Quality Problems4-1. Vertical Black Line and Band
Ⅳ. Troubleshooting
4. Printing Quality Problems4-2. Vertical White Line
Ⅳ. Troubleshooting
4. Printing Quality Problems4-3. Horizontal Black Band
Ⅳ. Troubleshooting
Charge roller = 37.7mmSupply roller = 44.92mmDevelop roller = 35.2mmTransfer roller = 45.3mm
4. Printing Quality Problems4-4. Black/White Spot
Ⅳ. Troubleshooting
4. Printing Quality Problems4-5. Light Image
Ⅳ. Troubleshooting
4. Printing Quality Problems4-6. Dark Image or a Black
Ⅳ. Troubleshooting
4. Printing Quality Problems4-7. Uneven Density
Ⅳ. Troubleshooting
4. Printing Quality Problems4-8. Background
Ⅳ. Troubleshooting
4. Printing Quality Problems4-9. Ghost(1)
Ⅳ. Troubleshooting
4. Printing Quality Problems4-10. Ghost(2)
Ⅳ. Troubleshooting
4. Printing Quality Problems4-11. Ghost(3)
Ⅳ. Troubleshooting
•Description Ghost occurs at 64.1 mm intervals.
64. 1 mm
4. Printing Quality Problems4-12. Ghost(4)
Ⅳ. Troubleshooting
35.2mm
•Description A White ghost occurs in a black image printing at 35.2mm intervals.
4. Printing Quality Problems4-13. Satins on front of the page
Ⅳ. Troubleshooting
4. Printing Quality Problems4-14. Satins on back of the page
Ⅳ. Troubleshooting
1. 45.3mm : Transfer roller is contaminated.
2. 75.5mm : Pressure roller is contaminated.
4. Printing Quality Problems4-15. Blank Page Print Out(1)
Ⅳ. Troubleshooting
4. Printing Quality Problems4-15. Blank Page Print Out(2)
Ⅳ. Troubleshooting
Review
Ⅳ. Troubleshooting
Ⅰ. What is most frequently happened trouble? Ⅱ. Can you classifying each “Paper Jam”? (Jam0,Jam1,Jam2,Bypass Jam)
Ⅲ. Are you familiar with Printing Quality Problems?
Ⅳ. Do you have more question for troubleshooting in Scanner part?
ReviewReview
The end