MERIT TELECOM (NIG.) LTD
Page 1
OPERATION GUIDELINE
SCAN MODE DRIVE
TEST
MERIT TELECOM (NIG.) LTD
Page 2
Written by Muhammad Ameen Reviewed by Tadeola O. Atalabi
Approved by Date 07-May-2009
Document No. MRTL-RF-GDL-001
MERIT TELECOM (NIG.) LTD
Page 3
Executive Summary
The purpose of this document is to give guidelines to engineers carrying out drive tests in Scan
Mode using TEMS Investigation tool. The document briefly explains how to configure TEMS
Investigation for scan mode drive testing, how to select channel groups for special frequencies
and how to export data to Mapinfo and other tools. The document briefly discusses the post
processing analysis as well.
MERIT TELECOM (NIG.) LTD
Page 4
TEMS Investigation supports scanning of GSM Radio Frequency carriers with SONY ERICSSON
Phones including K790i which Merittel is using extensively for its RF Activities. However, the
phone cannot act as an ordinary phone while it is scanning. In particular, it cannot engage in
voice calls or data transfer.
1.1 How to setup for Frequency Scanning Mode?
The scanning tasks are setup/configured from Equipment Control Bar shown below. The
buttons and combo box will be active once Phone and Dongle are connected to the system.
After connecting the devices, the above shown equipment control bar will become active.
Select MS1 from the Device Combo Box.
Select “[GSM] Frequency Scanning” from the scanning task combo box. Since Sony Ericsson
K790i is only GSM/DCS capable phone so the TEMS Investigation will not show any other
options like WCDMA Frequency Scanning etc.
Click the “Scanning Properties” button.
The “Measurement Settings” dialog box will show up as shown below. The options in the dialog
box might differ slightly depending upon the capabilities of the scanning devices.
MERIT TELECOM (NIG.) LTD
Page 5
The options on the dialog box are;
Manual Selection: Clicking will open a new dialog box where we can select the frequencies
whose scanning is intended. See section 1.1.1.
Decode BSIC: The check box should be checked as BSIC decoding is the requirement of
ZAIN Nigeria.
Decode SI on The check box should be checked for better post test analysis. Strongest Cell:
1.1.1 Channel Selection
On the following dialog box you can either configure the channel groups or can manually select
frequencies on your own accord. ZAIN Nigeria is using the following frequencies in their
network.
GSM [900 Band] : 101 – 116
DCS [1800 Band] : 736 - 763
The simplest way is to write the frequencies manually in the “Select Channels” box. The syntax
for writing ZAIN frequencies is;
101-116,736-763[1800]
MERIT TELECOM (NIG.) LTD
Page 6
You can also define your own channel groups by clicking on the “Define” button on the “Select
Channels Manually” dialog box.
Select Ok and return to Equipment Control Bar.
1.2 Performing a Scan
On the Equipment Control Bar, choose the device to scan with in the combo box
Select GSM Frequency Scanning.
Click connect.
Start recording the log file as per normal procedure.
Click the Start Scanning button.
Once you have finished traversing the intended drive test route, click the stop scan button.
Please note that during Scan Mode Drive Test, you will not be able to see any footprint in the
map inside TEMS investigation however, Scan Bar chart will keep showing changing signal levels
of various scanned frequencies.
1.3 Presenting the Data
There are multiple ways to present and analyze the scanned data.
1.3.1 Scan Bar Chart
TEMS Investigation has a built in chart for showing scanned data. To open a scanned bar chart,
Open the Navigation Pane and then click in the following order,
Navigation Pane Presentation GSMScanningScan Bar Chart
MERIT TELECOM (NIG.) LTD
Page 7
Once the Scan Bar Chart is displayed as shown below, the two separate charts could be
interpreted as;
The top chart by default shows the strongest scanned frequencies/channels sorted by
decreasing signal strength.
The bottom chart by default shows all scanned frequencies/channels in order of ascending
ARFCN.
1.3.2 Exporting the log file to Mapinfo
The log file could be exported in the same manner as being done for normal drive test log files
except that different “Information Elements” need to be selected for the export to MapInfo tab
format.
On the menu bar, click in the following order to make the necessary selection for Information
elements.
LogfileExport LogfileAdd order(on the Add Export Order dialong box, click)Setup, the
following window will show up;
MERIT TELECOM (NIG.) LTD
Page 8
Select the information elements as indicated. You may add extra ones depending on your
requirement for analysis.
The map could be drawn indicating signal level of one frequency on the entire route. For
example see frequency scan of Site ANA025 sector A with ARFCN 743 on the entire route.