MAN-001 Rev. 4 | Created 3-10-2020 | ECN-00519
This manual covers all Model 0304 and Model 0305 configurations
For service, parts, and customer support, contact us:
SECURITY ENGINEERED MACHINERY 5 Walkup Drive | Westborough, MA 01581
508-366-1488 | [email protected] www.semshred.com
SEM Model 0304 & 0305 Operation and Maintenance Manual
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 1
ContentsDisclaimers.............................................................................................................. 2Safety ..................................................................................................................... 3About Your Shredder - 0304 ................................................................................... 4 Overview and Intended Use ...................................................................................4Shredder Configuration ..................................................................................................4About Your Shredder - 0305 ................................................................................... 5 Overview and Intended Use ...................................................................................5 Shredder Configuration ..........................................................................................5 Acceptable Media – HDD Combo Chute ...............................................................6 Acceptable Media – SSD Combo Chute ................................................................6 Unacceptable Media ..............................................................................................6Unpacking and Installation .................................................................................... 7 Uncrating ................................................................................................................7General Installation ............................................................................................... 8Conveyor Shroud Installation ................................................................................. 9Assembling Dust Cover .......................................................................................... 9Electrical .............................................................................................................. 11 Installation ............................................................................................................11 Voltage Specifications...........................................................................................12Operation ............................................................................................................ 13 Standard and CE Control Scheme - 0304/0305 ...................................................13 Pre-Start Up ..........................................................................................................13 Start Up Procedure and Operation .....................................................................14 Shut-Down Procedure ..........................................................................................15Maintenance ......................................................................................................... 16 Maintenance Tools and PPE .................................................................................16 Maintenance Schedule .........................................................................................16 Air Filtration System ............................................................................................18 Current Relay Adjustment ....................................................................................21 Cutting Head Adjustment ...................................................................................22Maintenance Diagrams ......................................................................................... 23 General Layout - 0305 ..........................................................................................23 General Layout - 0304 ..........................................................................................24 Drive System .........................................................................................................25Extra Options and Spare Parts ............................................................................. 26
Model 0305 & 0304 Operation and Maintenance Manual
2 SEM | www.semshred.com
DisclaimersEvery care has been taken by the staff of SEM in compilation of the data contained in all training and informational materials (“collateral”) and in verification of its accuracy when published; however, the content of this collateral is subject to change without notice due to factors outside the control of SEM and this collateral should therefore be used as a guide only. The products referred to in these publications are continually improved through further research and development, which may lead to the alteration of information contained in this collateral. SEM does not accept any responsibility whatsoever for misrepresentation by any person of the information contained in this collateral and expressly disclaims any and all liability and responsibility to any person, whether a reader/viewer of this collateral or not, with respect to claims, losses, damage, or any other matter, either direct or consequential, arising out of or in relation to the use and reliance upon any information contained or products referred to in this collateral. SEM does not warrant that the equipment will work properly in all environments and applications, and makes no warranty or representation, either implied or expressed, with respect to the performance, throughput, or maintenance requirements of the machine. Performance, throughput, and maintenance requirements vary depending on screen size, feed rate, and media type as well as operational procedures. Information in this collateral is subject to change without notice and does not represent a commitment on the part of SEM. SEM assumes no responsibility for any inaccuracies that may be contained in this collateral or any omissions that may have occurred. SEM makes no commitment to update or keep current the information in this collateral and reserves the right to make improvements to this collateral and/or to the products described therein at any time without notice.
Proprietary Information: This document contains proprietary and confidential information of SEM, and shall not be used, disclosed or reproduced, in whole or in part, for any purpose, without the prior written consent of SEM. Title in and to this document and all information contained herein remains at all times in SEM. This information is exempted from disclosure under FOIA, as amended.
The combo SSD chute and SSD units intended for the destruction of solid state media only. Attempting to shred rotational drives in the SSD chute could cause catastrophic damage to the unit and will void warranty.
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 3
Safety
Read and understand instruction manual and be aware of all warning stickers.
Always follow proper PPE and lock out tag out procedures (LOTO).
Make sure that all guards and access panels are in place at all times, EXCEPT when the power is locked off for maintenance work or cleaning.
Always know where emergency stop buttons are located.
Always know or have quick access to emergency phone numbers.
Always ensure that all maintenance and operating personnel read and understand this manual, including those personnel working second or third shift.
Always have a standard break-in time for a new operator. A minimum of two hours is suggested.
Always wear safety glasses when operating shredder.
Always lock-out power at the disconnect when shredder is not in use, when servicing shredder, or when performing routine shredder maintenance. This includes cleaning.
Never operate this or any other machine while under the influence of drugs, alcohol, or medications.
Never wear loose fitting clothing, ties, or jewelry while in the vicinity of this shredder.
Never allow long hair to be in the vicinity of the machine without use of a protective hair net.
Never place any part of your body in or on any part of the machine while in operation.
Never allow other personnel within ten feet of this machine while in operation.
Never remove guards, perform maintenance, or clear jam up debris without first locking out power disconnect.
Never allow horse play around machine.
Never bypass or interfere with any safety limit switches or guards. They are safety devices and serious injury can result if bypassed.
Never allow minors to operate the machine.
Model 0305 & 0304 Operation and Maintenance Manual
4 SEM | www.semshred.com
About Your Shredder0304 For information about other cutting head configurations and features, such as wider feed chutes, 11” X 2.5” (option to 19.25”W), contact SEM customer care.
The maintenance and operation information in this manual is also applicable to the Model 0301 and 0302. Contact SEM Customer Care for electrical information or details about these devices.
Overview and Intended Use
The SEM Model 0304 HDD/SSD Shredder employs a 20 horsepower motor to de-stroy up to 3,000 rotational or solid state hard drives or up to 3,500 e-media devices (phones, RAM, etc.) per hour depending on the cutting head configuration chosen at purchase. This unit is also capable of destroying enterprise drives at a rate of up to 800 per hour, and up to 1,400 enterprise SSDs per hour. Solid state media can be destroyed with a combo HDD chute but SEM recommends using the combo SSD chute for higher security destruction.
Size and Weight: When fully assembled, the SEM Model 0304 is approximately 67” (170.18cm) tall by 65” (165.1cm) wide and 114” (289.56cm) deep. It weighs approxi-mately 4,700 lbs (2,100 kg).
Note: The images shown in this manual may appear slightly different due to the age of your machine and the features ordered with it. All functionality and locations re-main the same or very similar to your machine. Contact SEM customer service with any questions. Some iimages may show optional features that must be ordered at time of purchase.
Shredder Configuration
The SEM Model 0304 is designed to shred standard rotational hard drives, solid state drives, tapes and various electronic media depending on the cutting head configura-tion chosen at the time of purchase. Hard drive shreds at 1.5” or 0.75” shred widths. This can also shred SSDs but not to secure particle sizes.
HDD/SSD combo units have two cutting heads allowing destruction of both types of media. HDD can be shredded to 38mm/1.5”, while SSD can be shredded to 0.375”.
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 5
About Your Shredder0305
For information about other cutting head configurations and features, such as wider feed chutes or .375 SSD shred widths contact SEM customer care.
The maintenance and operation information in this manual is also applicable to the Model 0301 and 0302. Contact SEM Customer Care for electrical information or details about these devices.
Overview and Intended Use
The SEM Model 0305 HDD/SSD Shredder employs a 10 horsepower motor to de-stroy up to 3,000 rotational or solid state hard drives or up to 3,500 e-media devices (phones, RAM, etc.) per hour depending on the cutting head configuration chosen at purchase. This unit is also capable of destroying enterprise drives at a rate of up to 800 per hour, and up to 1,200 enterprise SSDs per hour. Solid state media can be destroyed with a combo HDD chute but SEM recommends using the combo SSD chute for higher security destruction.
Size and Weight: When fully assembled, the SEM Model 0305 is approximately 66” (167.64 cm) tall by 58” (147.32 cm) wide and 89” (226.06 cm) deep. It weighs approxi-mately 2,800 pounds (1270 kg).
Note: The images shown in this manual may appear slightly different due to the age of your machine and the features ordered with it. All functionality and locations re-main the same or very similar to your machine. Contact SEM customer service with any questions. Some images may show optional features that must be ordered at time of purchase.
Shredder Configuration
The SEM Model 0305 is designed to shred standard rotational hard drives, solid state drives, tapes and various electronic media depending on the cutting head configuration chosen at the time of purchase. Hard drive shreds at 1.5”shred widths. This can also shred SSDs but not to secure particle sizes. HDD/SSD combo units have two cutting heads allowing destruction of both types of media. HDD can be shredded to 1.5”, while SSD can be shredded to 0.375”.
Model 0305 & 0304 Operation and Maintenance Manual
6 SEM | www.semshred.com
Acceptable Media
HDD Combo Chute
The following media is acceptable to be destroyed with combo HDD chute:
• Rotational Hard Drive
• Enterprise Hard Drive
• Tapes
SSD Combo Chute
The following media is acceptable to be destroyed with an combo SSD chute:
• Solid State Drives
• Enterprise SSDs
Do not shred rotational hard drives using the combo SSD chute as damage to the machine may occur and your warranty will be voided.
Unacceptable Media
The following materials should never be destroyed used a SEM Model 0305 shredder.
• Batteries
• Capacitators
• LCDs
Batteries and capacitors should never be destroyed using this machine. Both can be found inside of cell phones, tablets, etc. They must be removed from all devices before shredding. Destruction of batteries could lead to safety hazards and cause damage to the machine. All batteries must be removed from cell phones, PDAs, tablets, etc. prior to destruction.
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 7
Unpacking and Installation Your new SEM shredder has been secured to a pallet for shipping. Please inspect equipment immediately for shipping damage.
• Note any damage to the packaging or unit on the bill of lading and contact SEM customer service.
• Retain packaging for 90 days.
• Using a lift truck with a minimum capacity of 4,000 lbs. Remove the machine from the carrier and transport to operation site. Remove pallet and discard responsibly after 90 days.
• SEM shredders are equipped with swivel casters for ease of handling.
• Inspect the machine for any damages prior to installation and operation. Check the oil level and check for any oil leaks.
• After inspection, make certain that all guards and safety devices are installed properly.
• If purchased, make sure to install the conveyor shroud and gaylord dust cover before operation.
• Consumables are also included within shipments.
Uncrating
• Fork lift with 4,000 or 6,000 lb. capacity, see above.
• Pry bar
• Strap cutters
• Hammer, drill
• #2 Phillips, T20, T25 Bits, 9/16”socket wrench
Unpacking:
• Remove front and top of crate with drill and appropriate bits marked with spraypaint. Cut straps holding the unit with strap cutters.
• Remove bolts holding brackets at the base of the unit in the front and back. Remove boards in front and on top of the unit.
• Remove the unit from the pallet and bring as close to installation point as possible with fork lift truck.
Model 0305 & 0304 Operation and Maintenance Manual
8 SEM | www.semshred.com
General Installation This machine may be installed in an office or warehouse setting within six feet of an appropriate electrical receptacle.
Note: The unit’s weight is mostly on the left side. Use care when moving and stay clear if it begins to tip.
Note: It is recommended to move the unit as close to the installation area as possible using a fork lift, particularly if it requires traversing uneven surfaces.
Storage: If unit requires storage, it can be stored in its shipping crate or unpackaged. If unpackaged, ensure that all caster locks are engaged.
To transport, unlock all caster locks and then push on a flat surface. Do not push this unit on inclined or declined surfaces as control of the unit may be lost and damage to the machine or injury to personnel may occur. Install the output conveyor if not installed. Requires metal shears, one 1-1/8” open wrench or adjustable wrench, 9/16” socket wrench, and 1/2” wrench.
• With the assistance of an overhead crane or a forklift, the conveyor can be hoisted into position. Use a sling to lift the conveyor assembly into place, then, using the bolts supplied at rear of machine, attach conveyor and tighten bolts.
• Install conveyor belt around drive pulley (under cutting head) and pull belt along belly pan and top plate. A second person may be necessary to bring both ends together. When both ends are put together, take extra care to align the lacing. When aligned properly, put connecting pin (supplied) through the lacing. Clip off any excess pin which may be hanging out.
• Tighten belt snug. Belt must be tight enough so that it cannot be stopped by a hand.
Remove hardware
from end of conveyor.
Reinstall bolts where they
were removed (both sides).
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 9
Conveyor Shroud InstallationInstall conveyor shroud if not installed. It is recommended that two people do this and requires 1/2” wrench, 1/2” socket, and 1-1/8” wrench. This section only applies to units purchased with the optional conveyor shroud.
• Remove hardware from the end of the conveyor. Loosen the nut holding the conveyor’s bearing covers and remove the covers.
• Have second person hold the shroud in place at the end of the conveyor and install the bolts into the holes from which they were removed.
• Ensure conveyor shroud side covers are on the outside.
• Tighten bolts and reinstall conveyor bearing covers.
• With the assistance of an overhead crane or a forklift, the conveyor can be hoisted into position. Use a sling to lift the conveyor assembly into place, then, using the six bolts supplied at rear of machine, attach conveyor and tighten bolts.
• Install conveyor belt around drive pulley (under cutting head) and pull belt along belly pan and top plate. A second person may be necessary to bring both ends together. When both ends are put together, take extra care to align the lacing. When aligned properly, put connecting pin (supplied) through the lacing. Clip off any excess pin which may be hanging out.
Assembling Dust CoverThis section only applies to units purchased with the optional dust cover.
• Open the box (not included) and unfold.
• Fold open the walls inside the base.
• May help to place a piece of wood inside to hold the shape. (Fig. 1)
• Staple or otherwise secure the walls to the base.
• Slide the opening in the middle of the cover around the conveyor shroud and tighten the cord. (Fig. 2)
• Slide the rest of the cover over the box. (Fig. 3)
• Guide the belt through the loops and tighten snugly. (Fig. 4, 5)
Model 0305 & 0304 Operation and Maintenance Manual
10 SEM | www.semshred.com
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 11
Electrical Installation
NOTE: All electrical MUST be completed by a licensed electrician.
• Be sure to follow proper “Lock Out Tag Out” (LOTO) procedures.
• A schematic can be found in both the electrical panel and debris drawer. Available in PDF on request.
• All units work on 3-phase AC power.
• All electrical installation must be done by a qualified electrician. Follow all national and local electrical codes and ordinances.
• All internal wiring has been factory installed and tested prior to shipping. Electrical installation consists of providing adequate machine power only.
• Check building service to ensure correct voltage is available and that the electrical current requirements can be met.
• Ensure area is clear. Turn the key switch on and turn E-STOP clockwise, ensuring it’s not engaged. Check for proper motor rotation. The conveyor belt should run away from the operator if the forward button is pressed. Motor rotation is dependent on how customer’s electrical panel is wired. If rotation is wrong, a licensed electrician can correct it.
• Electrical installation is complete. Replace all guards and safety devices.
• Notes: SEM recommends a less than 3% voltage drop on the receptacle/disconnect for optimal performance while under load.
• Run a few drives and adjust current relay as needed. See section 4.6 for information regarding adjusting current relay. Recommend using a licensed electrician.
Model 0305 & 0304 Operation and Maintenance Manual
12 SEM | www.semshred.com
Voltage Specifications
0305
Voltage / Frequency
Full Load Amps (FLA) [FLA with Air System]
Recommended Disconnect
Apparent Power (Line to Line) kVA
208V/60Hz 31 [36] 50 Amp 11.2 [13]
230V/60Hz 28 [33] 50 Amp 11.2 [13.1]
380V/50Hz 18.1 [20.4] 30 Amp 11.9 [13.4]
400-415V/50Hz 18 [20.3] 30 Amp 12.7 [14.3]
460V/60Hz 14 [16.1] 30 Amp 11.2 [12.8]
0304
Voltage / Frequency
Full Load Amps (FLA) [FLA with Air System]
Recommended Disconnect
Apparent Power (Line to Line) kVA
208V/60Hz 52.4 [55.8] 75 Amp 11.2 [13]
230V/60Hz 48.4 [51.6] 75 Amp 11.2 [13.1]
460V/60Hz 24.2 [25.8] 50 Amp 11.9 [13.4]
380,400-415V/50Hz 27.5 [29.2] 50 Amp 12.7 [14.3]
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 13
Operation Standard and CE Control Scheme
Depending on model, buttons may be in slightly different positions.
Emergency Stop: Immediately turns off power to the machine. Machine cannot turn on until disengaged. Twist to disengage.
Shredder Forward: Starts the machine.
Shredder Reverse: Makes the cutters rotate backwards to unjam the machine or help in cleaning waste from cutting head. Must be held down to run in reverse. Machine must be stopped before reversing.
Key Switch: Turns power to the machine on or off.
Shredder Stop: Stops the machine. Press the stop button anytime to stop the machine.
Hour Meter: Shows number of hours machine has operated.
Pre-Start Up
• Familiarize yourself with all controls and button locations.
• Ensure that all guards and covers are in place.
• A certified SEM service technician is available over the phone or on site for startup instruction and training. Contact SEM customer service for details and have your serial number available: [email protected].
Model 0305 & 0304 Operation and Maintenance Manual
14 SEM | www.semshred.com
Start Up Procedure and Operation
PPE: SEM recommends wearing safety glasses, mask, and gloves while operating this machine. However, each site should determine its own PPE.
Turn the KEY SWITCH on and disengage the E-STOP, then press the SHREDDER FORWARD BUTTON. The cutters will begin to rotate towards each other and the output conveyor will begin to run forward, away from the operator.
In Case of Emergency: The E-STOP button or turn the KEY SWITCH.
Feeding: Begin feeding material into the appropriate feed chute. Feed drives one at a time.
Chute Blocker: If this unit is equipped with a chute blocker, be sure that it is covering the correct chute. To change chutes, lift the knob and slide it towards the chute that is not in use.
Reminder: DO NOT SHRED ROTATIONAL HARD DRIVES USING THE SSD CHUTE.
New Operators: New operators should be given a minimum 2-3 hour equipment training time, beginning with a slow feed rate, approximately one drive every 10-15 seconds. The operator will soon be able to judge how quickly the shredder can be fed.
Debris Drawer Lock (Optional): The debris drawer is equipped with a lock and blue key if CE or specified at purchase. Turn the key before opening the drawer. Do not attempt to force the drawer open or open drawer while unit is running.
Important/Warning: The debris drawer is attached to keep excess material from col-lecting on floor. Drawer must be emptied frequently (approx. every 100 drives) or dam-age to the belt and unit may occur. Debris drawer should be emptied at the beginning and end of each operator’s shift regardless of the number of drives shredded.
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 15
Clearing a Jam
• In the event of a jam, ensure that all personnel are clear of both the input chute and the cutting head.
• Hold the SHREDDER REVERSE button for 5-7 seconds. This will cause the cutters to run backwards for as long as the reverse button remains pressed.
• Release the reverse button. The machine will come to a stop. After the machine has completely stopped, press the forward button and try to shred material.
• If machine jams again, reverse shredder, LOCK OUT POWER, and manually remove the jammed material.
• Restart machine in the forward direction to resume operation.
Warning: NEVER hold the forward button as damage to the machine and the elec-trical system may occur.
Shut-Down Procedure
• Allow input chute and output conveyor to clear all material before shutting down. Wait approximately 30 seconds.
• Press the Shredder Stop button. Turn Key Switch to off position and activate E-STOP.
• Turn off the disconnect switch. Begin daily cleaning.
• See section 4.2 for maintenance schedule.
Model 0305 & 0304 Operation and Maintenance Manual
16 SEM | www.semshred.com
MaintenanceMaintenance Tools and PPE
• Safety glasses and cut resistant gloves
• One 1-1/8” wrench or one adjustable wrench
• 7/16” and two 1/2” wrench or socket wrench
• Phillips head and flathead screwdriver
• 1-1/8” crowfoot wrench
• Grease gun with standard fitting
Maintenance Schedule
Daily:• Empty debris drawer (every 100 drives and before and after every shift).
• Wipe down machine with cleaning solution.
• Rake waste in gaylord to prevent pyramiding.
Every 15-20 Hours:• Open the conveyor rear access panel and clean debris from the cutters and inspect
air inlet. Remove any magnetic buildup over the air inlet.
• Grease main bearings, wear plates. There are eight grease fittings, four on each side of conveyor. Add 4 pumps of grease into each fitting. Warning: do not over-pump.
• Apply light machine oil to cutters.
• Check belt tension. If slipping or loose, tighten.
• Replace prefilter.
Every 30-40 Hours: • Apply oil to conveyor drive chains.
• Check oil level of spur gears.
• Clean HEPA filter (see air filtration section).
• Replace prefilter quarterly or as needed.
• Pliers
• WD-40
• Cleaning solution and rag
• Beam torque wrench 0-80in/lb range
• Adapters- 1/4” to 3/8”. and 3/8” to 1/2”
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 17
Lube Schedule
Conveyor Belt Adjustment
Setting Tension
Tools Required: 1-1/8” wrench or adjustable wrench, beam torque wrench (0-80 in./lb.), drive adapters, and 1-1/8” crowfoot wrench.
• Be sure to check belt tension every 20 hours. Belts stretch after break in period.
• Read all safety warnings before proceeding.
• De-energize the unit using proper LOTO procedures.
• Loosen bearing cover nut and remove bearing cover.
• Loosen jam nuts on each side of machine (see figure below). Leave 1/2” gap between jam nut and adjustment bracket.
• Use beam torque wrench, adapters, and 1-1/8” crowfoot wrench to tighten adjustment nuts to ensure torque range is between 40-50 in./lb.
• Ensure all personnel are clear and that no tools are on machine belt, or input chute.
ITEM FREQUENCY TYPECutters Every 15-20 hours Light machine oil
Main bearings, Wear Plates, Output Conveyor Pulley Bearings
Every 15-20 hours Multi-purpose grease (4 pumps per bearing)
Chain Every 30-40 hours Chain and cable lube
Jam NutAdjustment
top nutBearing Cover
Nut
Model 0305 & 0304 Operation and Maintenance Manual
18 SEM | www.semshred.com
• Turn machine on and run machine in forward for five minutes.
• Stop machine and turn power off. Draw a mark on each adjustment nut with a sharpie to track changes made in next step.
• Make all adjustments in small increments. By design, the conveyor belt should have 1/16” or less clearance between it and the side frames. Remove shroud if needed to check the alignment position.
• Adjust alignment by tightening adjustment nut one quarter turn at a time on the side of conveyor where the belt is rubbing the side frame. Tightening will move the belt away from the nut being tightened.
• Fully tighten jam nuts up to plate.
• Replace bearing covers.
• Turn power on and run machine in forward for five minutes.
If additional alignment is required, repeat the above steps.
Note: When the machine is run in reverse the belt may run slightly off center to the either side. This is normal. The belt will stretch during the first few days of operation. This will affect alignment since the belt alignment relies in part on proper tensioning for effective tracking.
Air Filtration System
The air filtration system (AFS) on this device is designed to help reduce possible odors and possible contaminants from escaping into the atmosphere during the process of hard drive destruction. The AFS is a low maintenance system that only requires periodic inspection, filter cleaning, and filter changes. The frequency of the inspections is dependent on usage.
HEPA Filter
Pre-Filter
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 19
Warning: Always de-energize the unit using proper LOTO procedures before cleaning, lubricating, maintaining, removing any guards, and after shredding operation is complete.
Note: See maintenance schedule for inspection, cleaning, and replacement frequencies.
Steps for checking Air Filtration System:
1. De-energize the unit using proper Lock Out Tag Out (LOTO) procedures.
2. Tools Required: 1/2” wrench or socket wrench
3. Inspect the air inlet of the AFS by removing the two bolts in the conveyor access panel on top of the conveyor on the rear of the unit and pulling up the cover to look inside. Inlet will be on the left from the rear of the machine.
4. Replace the prefilter. This can be accessed from the front of the shredder by removing the maintenance access panel below the control station. With panel removed, the prefilter will be exposed, and the prefilter can be removed. Note: Handle the prefilter with care. Do not jar or drop the prefilter as it is covered with dust from shredded media/drives.
5. Be sure to thoroughly clean the inside of the prefilter compartment, pulling out any strips or tape.
IMPORTANT: Prefilter must be installed so that the arrow is pointing towards the fan. The arrow on the frame of the prefilter points in the direction of the air flow. The air flow for the AFS goes from left to right.
Conveyor Access Bolts
Model 0305 & 0304 Operation and Maintenance Manual
20 SEM | www.semshred.com
6. The final inspection point is at the back of the shredder at the HEPA filter. Simply inspect the HEPA filter by visual observation. The side of the HEPA filter you can see should be an even white color across the entire surface. The HEPA filter will also have an airflow indicator arrow. Install the filter so that the arrow is pointing outwards from the machine.
a.) Clean the HEPA filter by placing in an empty bag with the airflow arrow facing up.
b.) Lift the filter approx. 1’ (0.3 m) from the ground and drop it several times.
c.) Vacuum both sides of the filter.
.
Note: If the HEPA filter does not appear to be white, then your prefilter could potentially be damaged and should be replaced. If there is an area on the surface of the HEPA filter that appears dark or dirtier than the rest of the filter, then your HEPA filter is potentially damaged and should be replaced.
Contact SEM at [email protected] for replacement parts or service.
HEPA Filter
Direction of Airflow
Fan
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 21
Current Relay Adjustment
Note: Before attempting to adjust the current relay contact SEM at [email protected].
Location: The electrical panel will be located either above the HEPA filter on the rear of the unit or behind the maintenance access panel on the front of the unit, located below the control panel.
Tools Required:
• 7/16” wrench or socket wrench
• Small Phillips or flathead screwdriver
Note: Press the SHREDDER STOP button before making any changes to the current relay. The power does not need to be off for this adjustment.
1. Remove cover to gain access to the current relay.
2. Turn knob labeled I-VALUE clockwise to the next tick mark.
3. Test the machine by feeding one drive at a time to ensure proper operation.
Warning: Over adjustment can cause the overload to trip which will not allow the machine to start until the overload has been reset.
Overload Resets
Current Relay
Model 0305 & 0304 Operation and Maintenance Manual
22 SEM | www.semshred.com
Cutting Head Adjustment
Be sure to de-energize the unit using proper LOTO procedures before adjusting the cutting head. SEM recommends using certified service personnel to adjust the cutting head if necessary.
• Over tightening of cutting head can result in excessive wear to wear plates and cutters. This may also shorten cutter and bearing life.
• Cutting head adjustments MUST be made on a COLD cutting head that has not been run within at least twelve hours.
• Ensure that the cutting head has been thoroughly cleaned and that the cutters move freely on the shafts.
Cutter clearance should be checked if any of the following conditions exist:
• Shred capacity drops noticeably.
• Media is passing through cutters without being completely shredded.
• Cutting head becomes extremely hot.
• Abnormal noise being generated from cutting head.
• Noticeable large gap between two cutters.
To Check/Set Cutter Clearance:
• Tools Required:
• 1/2” – 9/16” Wrench
• 3/16 Allen Wrench
• Lock out machine power to prevent injury.
• Remove rear guard.
• Clean and oil the cutting head ensuring that there are no obstructions.
• Locate the set screws on the chain side of the cutting head.
• Loosen the jam nut and using an Allen wrench to turn the screws clockwise to close the gap.
• Once the wear plate touches the cutter, back the screw off half a turn. Tighten the jam nuts and replace all guards and covers.
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 23
Conveyor Access Panel
Electrical Panel
HEPA Filter
Grease Lines (8 total, 4 on
each side)
Rear Access Panel
Conveyor Shroud
Output Conveyor
Chute Blocker
In-Feed Chute
Front Conveyor
Access panel
Debris Drawer
Controls
Maintenance Access Panel
Maintenance DiagramsGeneral Layout - 0305
Model 0305 & 0304 Operation and Maintenance Manual
24 SEM | www.semshred.com
Debris Drawer
In-Feed Chute
Maintenance Panel
Controls
Electrical Panel
(Inside)
Conveyor Access Panel
Output Conveyor
(No Shroud)
Output Conveyor Bolts
(Both Sides)
HEPA Filter (Optional,
Required for CE)
Grease lines (4 per side)
General Layout - 0304
Model 0305 & 0304 Operation and Maintenance Manual
SEM | www.semshred.com 25
Drive System
DESCRIPTION1 Drive Sprocket
2 Tension bracket
3 Idler Sprocket
4 One-way Sprocket Assembly
5 Drive Pulley
6 Drive Chain
7 Cutting Head Adjustment Screw
8 Grease Fittings
8 on back
23
7
1
6
4,5
Model 0305 & 0304 Operation and Maintenance Manual
26 SEM | www.semshred.com
TroubleshootingWARNING: Lock out power before performing any cleaning, oiling, maintenance or troubleshooting.
Problem Possible Cause SolutionMachine will not run (FWD or REV)
No power Check power supply for proper incoming power.
Keyswitch / ESTOP in. Turn to ON position.
Blown fuse / disconnect. Check fuses in disconnect and transformer.
Shredder STOP button remains depressed.
Check buttons.
Overloads Tripping Low voltage
Check for proper power (max 3% drop)
Current relay set too high.
Clear jam
Dirty cutting head. Consult factory setting for current relay.
Shredding capacity is low Dirty cutting head. Clean and lubricate.
Low voltage. Check incoming power.
Current relay. Consult factory.
Extra Options and Spare PartsBelow is a list of spare parts and extras offered for the Model 0305/0304
Description MPNReplacement HEPA Filter 600SHDHEPA
Replacement Pre-Filter 600HDSAFS-PREFILT
Replacement Conveyor Belt Contact Customer Care
Replacement Conveyor Side Rail Kit Contact Customer Care
For service, parts, and customer support, contact us:
SECURITY ENGINEERED MACHINERY 5 Walkup Drive • Westborough, MA 01581
508-366-1488 | [email protected] www.semshred.com
Follow us on social media:
Facebook: https://www.facebook.com/semshred
Twitter: https://twitter.com/semsecure
Linkedin: https://www.linkedin.com/company/security-engineeredmachinery
Youtube: https://www.youtube.com/user/datadestruction