SLIM COMBOSetup guide
Guide d'installation
English 3
Français 7
Español 11
Português 15
KNOW YOUR PRODUCT
Holder of iPad
Microphone hole
Any Angle stand
Magnetic spine toconnect iPadKeyboard LED
Shortcut keys
Keyboard
Keyboardpower button
Micro USBcharging port
iPad volume up/downiPad power button
Holder for stylusor digital pencil
SLIM COMBOSetup guide
English
SETTING UP THE CASE1. Insert iPad into iPad holder, and press down
until it clicks into place. Make sure the camera and microphone match up to the openings on the iPad holder.
2. If you have a stylus or digital pencil, slide it into the holder on the side of the case.
ESTABLISHING THE CONNECTION To pair your keyboard case with your iPad:1. Switch on the power button. If the LED status
light is red, charge the keyboard.2. On your iPad, make sure Bluetooth® is on.
– Select Settings > Bluetooth > On.– Select “iPad” from the Devices menu.
3. Press the Bluetooth® connect button on the keyboard for 2 seconds until the status light blinks. The keyboard is discoverable for 3 minutes.
4. If your iPad requests a PIN, enter it using the keyboard (not on the iPad), then press ENTER.
5. When a successful connection is made, the status light stays on for a short time, then turns o�.
FOUR VERSATILE MODES1. Typing modePull out the stand on the back of the iPad holder to the desired angle. Attach the keyboard, and place the iPad case on a �at surface to start typing.
2. Viewing modeDetach the keyboard. Pull out the stand on the back of the iPad holder to the desired angle.
4. Reading modeDetach the keyboard. Close the stand on the back of the iPad holder, and hold in portrait orientation for the optimum reading position.
3. Studio modeDetach the keyboard. Pull out the stand on the back of the iPad holder until the iPad is in a comfortable drawing position.
2s
ON
20-70°
English
DETACHING YOUR iPAD1. To detach your iPad from the case, lay it on
a at surface.2. Press down on one corner of the iPad holder
to release one side of the iPad; repeat on the opposite corner.
3. Lift the iPad from the bottom to release it from the case.
SHORTCUT KEYS
LED LIGHT INDICATORS
LED Behavior StatusBlinking green Battery is chargingSolid green Battery is fully charged (100%)Red Battery level is low (less than 10%), recharge the batteryBlinking white Fast: Keyboard is in discovery mode, ready for pairing Slow: Keyboard is trying to reconnect to iPadSolid white Bluetooth® pairing or reconnection is successful
ctrl
shift
Home
Switchlanguage
Keyboardbrightness
down
Keyboardbrightness
up
Search Virtualkeyboard
Previoustrack
Play/pause
Nexttrack
Mute Volumedown
Volumeup
Bluetooth Batterycheck
Lockscreen
English
CHARGING THE BATTERYIf the status light is red, the keyboard folio battery needs to be charged.1. Plug one end of the micro-USB cable into the
charging port and the other end into a USB port on your computer.Alternatively, you can use a USB charger, provided the power output rating is no more than 5V-500mA.The status light blinks green as the battery charges.
2. Charge the battery until the status light turnssolid green.
BATTERY DISPOSAL1. Pry o� top cover of keyboard with screwdriver.2. Detach battery from circuit board and remove
battery.3. Dispose of your product and battery according
to local laws.
BATTERY INFORMATION• A fully charged battery provides about 3 months
of use when the keyboard is used about two hours a day.
• Charge the battery if the status light turns red brie�y after the keyboard turns on.
• When not in use, turn o� the keyboard to conserve battery power.
• The keyboard enters sleep mode automatically if not used for a while in the typing position. Press any key to wake it.
Battery
English
PRÉSENTATION DU PRODUIT
Support pour iPad
Trou pour le microphone
Support multi-angle
Tranche magnétique pour connecter un iPadTémoin lumineux du clavier
Touches de raccourci
Clavier
Bouton d'alimentation du clavier
Câble de charge micro USB
Volume +/- de l'iPadBouton d'alimentation de l'iPad
Support pour stylet ou stylo numérique
SLIM COMBOGuide d'installation
Français
INSTALLATION DE L'ÉTUI1. Insérez l'iPad dans le support pour iPad, puis appuyez
vers le bas jusqu'à ce qu'il s'enclenche. Véri�ez que l'appareil photo et le microphone correspondent aux ouvertures du support pour iPad.
2. Si vous possédez un stylet ou un stylo numérique, glissez-le dans le support sur le côté de l'étui.
ÉTABLISSEMENT DE LA CONNEXION Pour coupler votre étui clavier à votre iPad:1. Basculez le bouton d'alimentation sur "ON". Si le témoin
d'état s'allume en rouge, chargez le clavier.2. Sur votre iPad, assurez-vous que le Bluetooth® est activé.
– Sélectionnez Paramètres > Bluetooth > Activé.– Sélectionnez "iPad" dans le menu Dispositifs.
3. Appuyez sur le bouton de connexion Bluetooth® sur le clavier pendant 2 secondes jusqu'à ce que le témoin d'état clignote. Le clavier passe en mode de détection pendant trois minutes.
4. Si votre iPad vous demande un code PIN, saisissez-le à l'aide du clavier (et non de l'iPad), puis appuyez sur ENTRÉE.
5. Lorsque la connexion est établie, le témoin d'état reste allumé un bref instant, puis s'éteint
QUATRE MODES POLYVALENTS1. Mode SaisieTirez le support situé à l'arrière du support de l'iPad et positionnez-le à l'angle souhaité. Fixez le clavier et placez l'étui de l'iPad Pro sur une surface plate pour commencer à taper.
2. Mode VisionnageDétachez le clavier. Tirez le support situé à l'arrière du support de l'iPad et positionnez-le à l'angle souhaité.
4. Mode LectureDétachez le clavier. Fermez le support situé à l'arrière du support de l'iPad et tenez-le en mode portrait pour une position de lecture optimale.
3. Mode StudioDétachez le clavier. Tirez le support situé à l'arrière du support de l'iPad jusqu'à ce que l'iPad se trouve dans une position de dessin confortable.
2s
ON
20-70°
Français
RETRAIT DE L'IPAD1. Pour retirer votre iPad de l'étui, posez-le sur
une surface plate.2. Appuyez sur un angle du support de l'iPad pour
faire sortir un côté de l'iPad; répétez l'opération du côté opposé.
3. Soulevez l'iPad par le bas pour le faire sortir de l'étui.
TOUCHES DE RACCOURCI
TÉMOINS LUMINEUX
Comportement des témoins lumineux ÉtatVert clignotant La batterie est en cours de chargeVert en continu La batterie est entièrement chargée (100 %).Rouge Le niveau de charge est faible (inférieur à 10 %), rechargez la batterieBlanc clignotant Rapide: le clavier est en mode de détection et prêt à être couplé Lent: le clavier tente de se reconnecter à iPadBlanc en continu Le couplage ou la reconnexion Bluetooth® sont e�ectifs
ctrl
shift
Accueil
Changer de langue
Réduction de la luminosité
du clavier
Augmentation de la luminosité
du clavier
Recherche Clavier virtuel
Piste précédente
Lecture/pause
Piste suivante
Sourdine Volume – Volume + Bluetooth Vérification des piles
Verrouillage d'écran
Français
CHARGE DE LA BATTERIESi le témoin d'état est rouge, vous devez charger la batterie de l'étui Keyboard Folio.1. Branchez l'une des extrémités du câble micro-USB
sur un port de charge, et l'autre sur le port USB de votre ordinateur.Vous pouvez également utiliser un chargeur USB, à condition que la puissance nominale ne soit pas supérieure à 5 V - 500 mA.Le témoin d'état clignote en vert pendant le chargement de la batterie.
2. Rechargez la batterie jusqu'à ce que le témoin d'état a�che une lumière verte continue.
RECYCLAGE DES BATTERIES USAGÉES1. Retirez le couvercle du clavier à l'aide d'un tournevis.2. Détachez la batterie du circuit imprimé et retirez-la.3. Mettez au rebut le produit et sa batterie
conformément à la législation locale.
INFORMATIONS SUR LA BATTERIE• Chargée au maximum, la batterie a une auto-
nomie de 3 mois, dans le cas d'une utilisation du clavier moyenne de deux heures par jour.
• Rechargez la batterie si le témoin d'état clignote en rouge brièvement après la mise sous tension du clavier.
• Lorsque vous n'utilisez pas le clavier, éteignez-le pour préserver la batterie.
• Le clavier entre automatiquement en veille s'il n'est pas utilisé pendant un certain temps en position de frappe. Appuyez sur une touche pour le réactiver.
Batterie
Français
COMPONENTES DEL PRODUCTO
Soporte para iPad
Ori�cio de micrófono
Soporte multiángulo
Lomo magnético para acoplamiento de iPadLED de tecladoTeclas de acceso
directo
Teclado
Botón de encendido del teclado
Puerto de carga micro USB
Subir y bajar volumen de iPadBotón de encendido del iPad
Soporte para stylus o lápiz digital
SLIM COMBOGuía de instalación
Español
COLOCACIÓN DE LA FUNDA1. Inserta el iPad en el soporte para iPad y presiona hacia
abajo hasta que encaje con un "click". Asegúrate de que la cámara y el micrófono coinciden con las aberturas del soporte para iPad.
2. Si tienes un stylus o lápiz digital, deslízalo en el soporte situado en el lateral de la funda.
ESTABLECIMIENTO DE LA CONEXIÓN Para emparejar la funda con teclado y el iPad:1. Desliza el botón de encendido. Si el diodo de estado
es rojo, carga el teclado.2. En el iPad, asegúrate de que está activada la función
Bluetooth®.– Selecciona Ajustes > Bluetooth > Activado.– En el menú de dispositivos, selecciona “iPad”.
3. Mantén pulsado el botón de conexión Bluetooth® durante dos segundos hasta que el diodo de estado emita destellos. El teclado es detectable durante 3 minutos.
4. Si el iPad solicita un PIN, introdúcelo mediante el teclado (en lugar del iPad) y pulsa INTRO.
5. Al establecerse correctamente una conexión, el diodo de estado permanece encendido durante unos momentos, luego se apaga
CUATRO MODOS DE USO1. Modo de escrituraColoca en el ángulo deseado la pieza retráctil de la parte posterior del soporte para iPad Acopla el teclado y coloca la funda para iPad en una super�cie plana para empezar a escribir.
2. Modo de visualizaciónDesacopla el teclado. Coloca en el ángulo deseado la pieza retráctil de la parte posterior del soporte para iPad.
4. Modo de lecturaDesacopla el teclado. Pliega la pieza retráctil de la parte posterior del soporte para iPad y mantenlo con orientación vertical para una posición de lectura óptima.
3. Modo de estudioDesacopla el teclado. Coloca en el ángulo deseado la pieza retráctil de la parte posterior del soporte para iPad hasta que el iPad esté en una posición cómoda para dibujar.
2s
ON
ACTIVADO
20-70°
Español
DESACOPLAMIENTO DEL IPAD1. Para desacoplar el iPad de la funda, apóyalo sobre
una supercie plana.2. Presiona una esquina del soporte para iPad para
liberar un lado del iPad. Repite para la esquina opuesta.
3. Levanta el iPad por la parte inferior para sacarlo de la funda.
TECLAS DE ACCESO DIRECTO
INDICADORES LUMINOSOS LED
LED EstadoDestellos verdes La batería se está cargandoVerde permanente La batería está totalmente cargada (100%)Rojo El nivel de carga es bajo (menos del 10%), recarga la bateríaDestellos blancos Rápidos: El teclado está en modo de detección, listo para el emparejamiento Lentos: El teclado está intentando reconectarse al iPadBlanco permanente El emparejamiento o la reconexión Bluetooth® se realizó correctamente
ctrl
shift
Inicio
Cambiar idioma
Reduce el brillo del teclado
Aumenta el brillo del teclado
Búsqueda Teclado virtual
Pista anterior
Reproducir/pausa
Pista siguiente
Silencio Bajar volumen Subir volumen Bluetooth Comprobación de baterías
Bloqueo de pantalla
Español
CARGA DE LA BATERÍASi el diodo de estado es rojo, es preciso cargar la batería de la funda con teclado.1. Conecta un extremo del cable micro USB al puerto
de carga y el otro a un puerto USB de la computadora.También puedes usar un cargador USB siempre y cuando el voltaje de salida no supere los 5 V y 500 mA.El diodo de estado emite destellos verdes mientras se carga la batería.
2. Carga la batería hasta que el diodo de estado emita una luz verde permanente.
PARA DESECHAR LA BATERÍA1. Ejerce palanca con un destornillador para retirar
la tapa superior del teclado.2. Desconecta la batería de la placa y retírala.3. Deshazte del producto y su batería de acuerdo
con las normas de legislación local.
INFORMACIÓN SOBRE BATERÍAS• Si la batería tiene una carga completa, puede durar
unos tres meses con un uso medio del teclado de dos horas diarias.
• Carga la batería si el diodo de estado emite luz roja brevemente después de encender el teclado.
• Cuando no uses el teclado, apágalo para conservar la carga de la batería.
• El teclado entra automáticamente en modo de suspensión si no se utiliza durante cierto tiempo mientras está en posición de escritura. Pulsa cualquier tecla para reactivarlo.
Batería
Español
CONHEÇA O SEU PRODUTO
Suporte para iPad
Abertura do microfone
Suporte para múltiplos ângulos
Faixa magnética para conectar ao iPad ProIndicador de luz em LED
Teclas de atalho
Teclado
Botão de energia do teclado
Porta de carregamento micro USB
Botões de volume do iPadBotão de energia do iPad
Suporte para caneta ou lápis digital
SLIM COMBOGuia de instalação
Portuguese
INSTALAÇÃO DA CAPA1. Insira o iPad no suporte do iPad e pressione para baixo
até encaixá-lo. Certi�que-se de que a câmera e o microfone estão no mesmo lugar das aberturas no suporte do iPad.
2. Se você possuir uma caneta ou lápis digital, guarde no suporte na lateral do estojo.
ESTABELECENDO A CONEXÃO Para parear a sua capa com teclado e seu iPad:1. Ligue o botão de energia. Se a luz de status do LED estiver
vermelha, carregue o teclado.2. No seu iPad, certi�que-se de que o Bluetooth®
esteja ligado.– Selecione Settings > Bluetooth > On.– Selecione “iPad” no menu Dispositivos.
3. Pressione o botão de conexão do Bluetooth® no teclado por 2 segundos até que a luz de status pisque. O teclado �ca detectável por três minutos.
4. Se o seu iPad solicitar um código PIN, insira-o usando o teclado (não no iPad) e pressione ENTER.
5. Quando uma conexão é estabelecida com êxito, a luz de status azul acende-se por um curto período, apagando-se em seguida.
QUATRO MODOS VERSÁTEIS1. Modo de digitaçãoAjuste o suporte traseiro do iPad para o ângulo desejado. Acople o teclado e coloque a capa do iPad em uma superfície plana para começar a digitar.
2. Modo de visualizaçãoDesacople o teclado. Ajuste o suporte traseiro do iPad para o ângulo desejado.
4. Modo de leituraDesacople o teclado. Feche o suporte traseiro do iPad e mantenha a orientação retrato para obter a melhor posição para leitura.
3. Modo estúdioDesacople o teclado. Ajuste o suporte traseiro do iPad para que esteja em uma posição de desenho confortável.
2s
ON
ATIVADO
20-70°
Portuguese
REMOVENDO O IPAD1. Para soltar o iPad da capa, posicione-o em
uma superfície plana.2. Precione um dos cantos da capa do iPad para
liberar um lado do iPad. Repita o procedimento ao canto oposto.
3. Erga o iPad para soltá-lo da capa.
TECLAS DE ATALHO
INDICADORES DE LUZ LED
Comportamento do LED StatusVerde piscando A bateria está sendo carregadaVerde estável A bateria está totalmente carregada (100%)Vermelho Nível de bateria está baixo (menos de 10%), recarregue a bateriaBranco piscando Rapidamente: teclado está no modo de detecção, pronto para o pareamento Lento: o teclado está tentando se reconectar ao iPadBranco estável O pareamento ou a reconexão do Bluetooth® teve êxito
ctrl
shift
Início
Alternar idioma
Reduzir brilho da luz
do teclado
Aumentar brilho da luz
do teclado
Pesquisar Teclado virtual
Faixa anterior
Reproduzir/Pausar
Próxima faixa
Sem som Diminuir volume
Aumentar volume
Bluetooth Verificação da bateria
Bloquear tela
Portuguese
CARREGANDO A BATERIASe a luz de status vermelha acender, a bateria do teclado folio precisa ser carregada.1. Conecte uma extremidade do cabo mini-USB
à porta de carregamento e a outra extremidade à porta USB no computador.Como alternativa, você pode usar um carregador USB contanto que a taxa de saída de energia não seja maior do que 5 V - 500 mA.A luz de status verde piscará enquanto a bateria é carregada.
2. Carregue a bateria até a luz de status verde �car estável.
DESCARTE DA BATERIA1. Remova a capa superior do teclado com uma chave
de fenda.2. Desconecte a bateria da placa de circuitos
e remova-a.3. Descarte o produto e a bateria de acordo com
as leis locais.
INFORMAÇÕES DA BATERIA• Uma bateria completamente carregada fornece
energia por cerca de três meses de uso quando o teclado é usado por cerca de duas horas por dia.
• Carregue a bateria se a luz de status vermelha acender-se brevemente depois de o teclado ser ligado.
• Quando não em uso, desligue o teclado para poupar energia da bateria.
• O teclado entra no modo de hibernação automaticamente quando não é usado por um período de tempo na posição de digitação. Pressione qualquer tecla para ligá-lo novamente.
Bateria
Portuguese
© 2018 Logitech, Logi and the Logitech Logo are trademarks or registered trademarks of Logitech Europe S A and/or its affiliates in the U S and other countries
© 2018 Logitech, Logi et le logo Logitech sont des marques commerciales ou déposées de Logitech Europe S A et/ou de ses sociétés affiliées aux États-Unis et dans d’autres pays
WEB-621-001166 002