7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
1/35
STRESS ANALYSIS ON POWER DRIVE GEAR OF
BFU-5 MILLING MACHINE USING FINITE
ELEMENT METHODA PROJECT REPORT
Submitted by
D. MANJU
I. LAKME @ ASHYA
Inpartial fulfillment for the award of the degree
of
BACHELOR OF TECHNOLOGYIN
MECHANICAL ENGINEERING
Under the guidance of
Mr.S. GUNABALAN,
Assistant Professor- Mechanical Department
BHARATHIYAR COLLEGE OF ENGINEERING AND
TECHNOLOGYKARAIKAL
PONDICHERRY UNIVERSITY: PUDUCHERRY
MAY 2010
1
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
2/35
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
3/35
ACKNOWLEDGEMENT
Several people have directly or indirectly contributed towards the development and
success of this project. It is indeed of a great pleasure to acknowledge the help of all these
individuals.
We wish to express our sincere thanks to our beloved Principal,
Prof. Dr. V.JAYARAMAN and Prof. C.RAVICHANDRAN our Head of Department of
Mechanical Engineering for his kind permission to work on this project.
We are greatly indebted to our project guide Mr.S.GUNABALAN,Asst. Professor
of the Department of Mechanical Engineering for his valuable guidance, advice and highly
useful suggestion without which this project would not have been brought to this successful
completion.
Last but not the least, we take great pleasure and consider it a proud privilege to
express our indebtedness and gratitude to our Senior Lecturers Mr.K.MARIMUTHU
,Ms.S.SRIDEVI ,Mr.VIJAYANAND and Staff Mr.JAGADESH ,Mr. JOSEPH
,Mr.GANESH of the department of mechanical engineering for their support in successful
completion of this project.
We also thank all the teaching and non-teaching staffs of our department for providing
us with valuable suggestion and kind cooperation for the project without any inhibition.
3
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
4/35
ABSTRACT
From smaller watches an instruments to heaviest and most powerful machineries
like lifting cranes spur gear is used to transmit the power from negligibly small values
thousands of KW using gears of diameter from a few mm to many meters. They are used in
automobiles, hoisting machineries rolling mills, machining tools such as lathes, milling
machines, shaping machines and so on.
Gear drives should be designed in such a way that they should overcome the
following gear failures:
Tooth breakage is caused due to over loads of either impact or static action
,repeated overloads causes low endurance fatigue .To overcome this gear material of
sufficient beam strength may be selected.
Pitting of tooth surface is caused due to over pressing of the tooth of one gear to the
tooth of mating gear. During continuous operation a crack may be formed which may
increase in size and change into pits .To prevent pitting the tooth are checked for
surface endurance.
Abrasive wear is the principle reason for the failure of open and closed gearing of
machineries operated in media, polluted by abrasive materials. This increases
dynamic load, noise, weakens the tooth and finally leads to breakage. To prevent this
gear can be protected from corrosive atmosphere.
Seizing of the tooth is due to crushing of oil film on the tooth surface under high
pressure leading to scores and scratches on its surface. To prevent this operating
temperature and properties of lubricants are properly maintained.
4
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
5/35
CHAPTER I
INTRODUCTION:
1.1 What is Gear:
A gear is a toothed wheel designed to transmit torque to another gear or toothed
component .This simple mechanism is well known since humankind started to deal with
machineries.
Early engineers developed wood gears with cylindrical pegs for cogs to multiply
torque and to change speed properties of different shafts. Subsequently cogs were replaced
by teeth and many archaeological discoveries had revealed that ancient civilizations (100
b.c.) used gears for a large variety of purposes,
From a single spur gear pair in water mill, to differential gear systems in very
complex astronomical calculating device, such as the Antikythera mechanism.
1.2 TYPES OF GEARS:
The following are the main types of gears:
Spur gear
Helical gear
Bevel gear
Worm gear
Rack and Pinion ,and so on
.
1.3 Spur Gear:
5
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
6/35
Spur gear is cylindrical in shape, with teeth on the outer circumference that
are straight and parallel to the axis (hole).There are a number of variations of the basic spur
gear ,including pinion wire, stem pinions, rack and internal gears.
Gears are used in many mechanical devices. Gears are a simple machine that
can give you a mechanical advantage. The components of any mechanical devices could be
broken down into simple machines. There are six basic simple machines: lever, pulley, wheel
and axle, inclined plane, wedge, and screw. The gear is considered to be within the wheel and
axle category of simple machines. Gears
(1) transmit motion,
(2) increase/decrease speed, and
(3) increase/decrease torque (power).
Gears can be divided into three major classes: parallel-axis gears, nonparallel but
coplanar gears, and nonparallel and non-coplanar gears. Parallel-axis gears are the simplest
and the most universal type of gear. They may transfer very much power and the high
efficiency in this classification, while spur gear is the main kind of gears.
1.4 Gear nomenclature:
6
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
7/35
fig 1.1
Addendum:
The radial distance between the Pitch Circle and the top of the teeth.
Centre Distance:
The distance between centres of two gears.
Circular Pitch:
Inches of Pitch Circle circumference per tooth.
Circular Thickness:
The thickness of the tooth measured along an arc following the Pitch Circle
Clearance:
The distance between the top of a tooth and the bottom of the space into
which it fits on the meshing gear.
Dedendum:
The radial distance between the bottom of the space between teeth and the top
of the teeth.
Diametral Pitch:
Teeth per inch of diameter. Sometimes written (incorrectly) as Diametrical
Pitch.
Face:
The working surface of a gear tooth, located between the pitch diameter and
the top of the tooth.
Face Width:
The width of the tooth measured parallel to the gear axis.
Flank:The working surface of a gear tooth, located between the pitch diameter and
the bottom of the space between gear teeth
Module:
Teeth per millimeter of Pitch Diameter
Pitch Circle:
7
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
8/35
The circle, the radius of which is equal to the distance from the center of the
gear to the pitch point.
Pitch Diameter:
Diameter of the pitch circle
Pressure Angle:
Angle between the Line of Action and a line perpendicular to the Line of
Centres
Root Circle:
The circle that passes through the bottom of the tooth spaces.
Root Diameter:
The diameter of the Root Circle
Pitch) for a given Pitch Diameter.
Whole Depth:
The distance between the top of the teeth and the bottom of the spaces
between teeth.
Working Depth:
The depth to which a tooth extends into the space between teeth on the mating
gear.
1.5 SPUR GEAR APPLICATIONS:
From smaller watches an instruments to heaviest and most powerful machineries
like lifting cranes spur gear is used to transmit the power from negligibly small values
thousands of KW using gears of diameter from a few mm to many meters.They are used in
automobiles,hoisting machineries rolling mills,machining tools such as lathes ,milling
machines,shaping machines and so on.
1.6 COMMON FAILURE WITH SPUR GEAR:
Gear drives shoud be designed in such a way that they should overcome the
following gear failures:
8
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
9/35
Tooth breakage is caused due to over loads of either impact or static action
,repeated overloads causes low endurance fatigue .To overcome this gear material of
sufficient beam strength may be selected.
Pitting of tooth surface is caused due to overpressing of the tooth of one gear to the
tooth of mating gear.During continous operation a crack may be formed which may
increase in size and change into pits .To prevent pitting the tooths are checked for
surface endurance.
Abrassive wear is the principle reason for the failure of open and closed gearing of
machineries operated in media,polluted by abrassive materials. This increases
dynamic load, noise, weakenes the tooth and finally leads to breakage.To prevent this
gear can be protected from corrosive atmosphere.
Seizing of the tooth is due to crushing of oil flim on the tooth surface under high
pressure leading to scores and cratches on its surface.To prevent this operating
temperature and properties of lubricants are properly maintained.
9
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
10/35
CHAPTER II
PROBLEM IDENTIFICATION
2.1 PROBLEM IDENTIFICATION:
The common failure encountered in spur gear is tooth failure.Spur gear found wide
application in all machining parts. Therfore gear failure cause heavy loss and economic loss
to end users.
Spur gear clip(fig 2.1)
The main cause of spur gear tooth failure are
i. Continous usage
ii. Due to wear
10
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
11/35
iii. Fracture
Hence it is felt that a detail study is required to find out the cause for tooth failure and
FEA is required to overcome the set failures. In this project a detailed modeling and FEA
was done to address the above problem.
11
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
12/35
CHAPTER III
METHODOLOGY
3.1 METHODOLOGY:
To execute the project study we have followed the methodology given below:
a) REVERSE ENGINEERING:
To find out geometrical and mechanical properties of the spur gear which is under
study.
a. Calculating dimensions using Profile Projector and Vernier Calliper.
b. Microstructure Analysis Material properties identification.
c. Hardenability test to measure depth of hardness for identifying whether the
material is case hardened.
b) MODELLING:
1. AUTOCAD 2000 is used to draw Spur gear.
2. The drawn Spur gear is imported in PRO-E3. IGES conversion is made and the PRO-E diagram is imported to
Ansys
c) FEA:
FEM tool provides exact gear geometry, relative positioning and the automatic
FEM discretization for a wide family of spur gears.
12
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
13/35
3.2 REVERSE ENGINEERING:
3.2.1 VERNIER MEASUREMENTS:
Vernier calliper is used to measure the dimensions of the Spur Gear accurately inmm .The measured dimensions are
No of teeth = 64
Addendum circle = 99mm
Inside diameter = 25mm
Face width = 20mm
Bush outside diameter = 25mm
Bush inside diameter = 22mm
Key width = 6mm
We cant find the tooth depth and tooth thickness using Vernier calliper. Hence we
have to go for Profile measurement using profile Projector.
13
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
14/35
3.2.2 PROFILE MEASUREMENTS:
Profile projectors magnification is 10 times larger than the original size .Small
objects are magnified and it is drawn in a paper and its dimensions are measured and the final
value divided by 10 gives the original value.
14
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
15/35
Gear Tooth with defects (fig 3.1)
Comparing the above 3 profile diagrams we conclude that
Tooth depth = 3.5mm
Tooth thickness = 1mm
15
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
16/35
3.2.3 MICROSTRUCTURE ANALYSIS:
Microstructure analysis is used to find the structure of the given specimen.
The surface of the specimen is polished using emery papers of grade 1/0,2/0,3/0,4/0.
Etchant nital 4% is applied on the polished surface.
The specimen is mounted on the telescopic microscope but the structure is not
identified due to continous usage of the gear.
So the surface is grinded for 0.5mm and the above procedure is done again.
Finaly by viewing in telescopic microspe we identified that the structure is Gray Cast
Iron.
Microstructure of Gray CI (fig 3.2)
16
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
17/35
3.2.4 HARDENABILITY TEST:
Rockwell hardness testing machine is used for testing the hardness of the
material . A straight line is drawn along the grinded surface of the gear and is divided into 6
equal parts measuring 5 mm each and readings are taken applying a load of 1500N (specified
for Cast iron).The following table shows the hardness value of the material.
Hardenability (fig 3.3)
17
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
18/35
ROCKWELL HARDNESS TEST:
Specimen Indenter Load
(kg f)
Dial gauge reading
Gray Cast Iron Diamond
(1/16 steel ball)
150
63.5
64.9
61.9
62.9
63.8
64
The readings obtained from the dial gauge are irregular so we conclude that the
surface is not case hardened,but the surface of the gear is somewhat hardened due to
machining.
18
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
19/35
3.2.5 DESIGN CALCULATION (manual):
INPUT:
Power(P)=1.1kw
Speed(N)=1400rpm
No of teeth pinion(Z1)=64
No of teeth of Gear(Z2)=84
Addendum circle diameter()=99mm
Inside diameter=25mm
Face width(F)=20mm
Tooth thickness=1mm
Tooth height=3.5mm
Pressure angle( )=20
SOLUTION:
MODULE(m)
Outer diameter=(No of teeth+2)Module
99=(64+2)m
m=1.5mm
ADDENDUM(a)
19
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
20/35
Addendum=module
a=1.5mm
DEDENDUM(b)
Dedendum=1.25*Addendum
b=1.25*1.5
b=1.8mm
CENTER DISTANCE(C)
m=2C/(Z1+Z2)
1.5=(2*C)/(64+84)
C=111mm
BOTTOM CLEARENCE(c)
c=0.25*m
c=0.25*1.5
c=0.2
c=0.3mm
PITCH DIAMETER(D)
D=m*Z1
D=1.5*64
D=96mm
DIAMETREL PITCH(Pd)
20
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
21/35
Pd=Z1/D
Pd=64/96
Pd=0.6mm
CIRCULAR PITCH(p)
p=D/Z1
p=(*96)/64
p=4.7mm
ROOT DIAMETER(df1)
df1=(Z1-2f )m-2c
df1=(64-2)1.5-2*0.2
df1=92.6mm
PITCH LINE VELOCITY(V)
V=DN/60
V=(mZ1N)/60
V=(*1.5*64*90)/60
V=0.452m/sec
TANGENTIAL LOAD(Wt)
Wt=(P/V)*Cs
Wt=(1.1*10^3/0.452)*1
Wt=2444.44m/sec
21
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
22/35
3.3 MODELLING:
Gear calculation values from MITCALC:
Since it is very difficult to draw a gear tooth exactly we downloaded a Gear
calculation software from MITCALC.
This gear calculation is already done by a person called JOHN DOE. In that
software we changed his input values and gave our calculated values from reverse
engineering and click the button Calc which automatically calculates the other parameters
which is needed for our designing.
SYMBOL EXPANSION VALUES UNITS
M Module 1.5 mm
A Addendum 1.5 mm
B Dedendum 1.8 mm
C Center distance 111 mm
C Bottom clearance 0.2 mm
D Pitch diameter 96 mm
P Diametral pitch 0.6 mm
P Circular pitch 4.7 mm
df1 Root diameter 92.6 mm
22
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
23/35
The values of manual calculation coincides with the MITCALC values. So we
conclude that our dimensional analysis is correct. Lets move to modelling.
3.3.1 DRAFTING - 2D:
CAD involves the designer's use of the computer as a versatile alternative to
more traditional modes of drawing and modelling and is today an indispensable tool for
graphic and product designers, engineers, interior designers, and architects.
Computer-aided design (CAD) is the use of computer technology for the
design of objects, real or virtual. CAD often involves more than just shapes. As in the manual
drafting of technical and engineering drawings, the output of CAD often must convey also
symbolic information such as materials, processes, dimensions, and tolerances, according to
application-specific conventions.
CAD may be used to design curves and figures in two-dimensional ("2D")
space; or curves, surfaces, and solids in three-dimensional ("3D") objects.
3.3.2 Design of Gear tooth:
Importing 2D drawing of gear tooth to Autocad by using MITCALC is shown
below
23
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
24/35
2D drawing of gear(fig 3.4)
Pinion model(fig 3.5)
24
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
25/35
Spur gear using autocad(fig 3.6)
3.3.3 INTRODUCTION TO PRO-E
In recent years, the computer has become a powerful tool in design and
manufacturing. CAD/CAM systems (Computer Aided Designing and Computer Aided
Manufacturing) can increase design accuracy, reduce lead times and improve overall
engineering productivity in the design and manufacturing industry.
Pro/Engineer is one of new CAD/CAE/CAM software in the world, featuring
the best operation in the design. The advantages are listed as the following:
1 Formidable, parameter design function permission, superior product
differentiated and manufacturability.
2 Integrates the application to develop out from the concept to the manufacture
within one kind of application.
3 The design change system allows you to float variable.
4 Completes the virtual simulation function to enable you to improve the
product performance and to surpass the product quality goal.
25
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
26/35
3.3.4 IMPORTING AUTOCAD DRAWING:
First setting the working directory, the file which is required is saved in
working directory that can be opened from any folder as we prefer . This is the main use of
setting working directory.
Now with the help of working directory the autocad drawing is opened in Pro-
e and necessary changes were made and is saved. Extrude the saved drawing for 20mm width
and save in IGES file.
26
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
27/35
Pro-e model(fig 3.7)
3.3.5 IGES
The Initial Graphics Exchange Specification (IGES) (pronounced eye-jess) defines
a neutral data format that allows the digital exchange of information among Computer-aided
design (CAD) systems
Using IGES, a CAD user can exchange product data models in the form of circuit
diagrams, wireframe, freeform surface or solid modeling representations. Applications
supported by IGES include traditional engineering drawings, models for analysis, and other
manufacturing functions
3.3.6. ANSYS:
INTRODUCTION TO ANSYS:
Ansys is a modeling software used in engineering drawings.The following
procedure is used for modelling in ansys.
First level in Ansys is Environment ie, file setting. Set the environment where
we are going to work.
Second level is analysis. It has four main menus, they are
PREFERENCES
27
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
28/35
What type of experiment we are going to do
Preference for GUI filtering -Structural
PREPROCESSOR
It is the key thing for any analysis .It includes modeling ,material properties
,load and so on.
ELMENTAL TYPE
Shell 93
MATERIAL PROPERTIES
Youngs Modulus=113000N/mm2
Poissons Ratio=0.25
SOLUTION
It solves the problem in preprocessor and gives the solution.
POSTPROCESSOR
It gives the report of the analysed model.
3.3.7 IMPORTING PRO-E MODEL:
The pro-e model in IGES form is imported to ANSYS and the procedures mentioned
above are done. The results are as shown below.
3.4 FINITE ELEMENT ANALYSIS:
The main part of the present work deals with the modeling of a spur gear and try to
give a unique approach to design gears, joining static and dynamics analyses.
28
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
29/35
FEM tool provides exact gear geometry, relative positioning and the automatic FEM
discretization for a wide family of spur gears. The code generates gear profiles based on
parameters describing the cutting tool and particular attention is paid on simulating the
enveloping process
In order to provide a FE model, a parametric routine is used to generate automatically
the mesh according to the teeth profiles geometry. This tool allows a fast and accurate static
analysis of the gear and the calculation of the main source of dynamic excitation, such as the
transmission error. The transmission error is strictly related to the variable global mesh
stiffness, which depends on the gear position, materials and teeth geometry.
A correct FEA can provide the value of the mesh stiffness, i.e. the transmission error.
In the second part of the work a single degree of freedom oscillator with clearance
type nonlinearity is considered. Such an oscillator represents the simplest model able to
analyze a single teeth gear pair.
29
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
30/35
Arresting all degrees of freedom(fig 3.8)
30
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
31/35
Meshing (fig 3.9)
The model is also able to predict the effect of detailed profile modifications and
manufacturing errors on the vibration of the spur gear .
3.4.1 SOLUTION OF FEA:
Von Mesis stress(fig 3.10)
Von Mesis stress analysis shows very less and well below the ultimate stress, so the
failure may not be due to working stress.
31
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
32/35
Drawing using profile projector(fig 3.11)
Shear stress(fig 3.12)
32
Breakage area
Breakage area
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
33/35
The figure 2.2 shows two main variations, ie dark blue and navy blue which has
values as -271.2 and +118.09.
The positive value represents tensile shear sress and negative value represents
compressive shear stress. When the gear revolves, changes occurs as compressive to tensile
and tensile to compressive alternatively.
Due to continuous change in shear stress, breakage occurs as shown in figure 2.2
along the boundary of the dark blue area.
Since this happens below the ultimate stress the breakage is due fatigue fracture after
150 to 200 hours of usage.
This is proved practically in the figure 2.1.
33
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
34/35
CHAPTER IV
CONCLUSION AND FUTURE SCOPE
4.1 CONCLUSION:
Project study reports on an extensive stress analysis of the toothed gear.
Particular interest is devoted to a study of the observed movement of the maximum-stress
position around the edge of the gear tooth associated with the variations due to shear loads.
A theoretical finite element model of spur gear system was developed. The research result
shows that the theoretical methods presented in this thesis have, good simulation accuracy.
This method could also be applied to many other engineering problems.
This study shows the Von Mesis stress analysis shows very less deviation.The
same way in this analysis it shows less deviation on the gear tooth except the edge of the
tooth where the load is applied and it is exceptional.
So from the following analysis we conclude that breakage occurs mainly due to
Fatigue fracture and not due to material properties.Wear fracture possibility is more due to no
surface hardening.
4.2 FUTURE SCOPE:
The present study can be applied to other types of gears such as Worm gear, Helical
gear and so on. The shear stress analysis can be further extended to other kind of analysis
such as wear , temperature distribution and so on.
34
7/27/2019 STRESS ANALYSIS ON POWER DRIVE GEAR OF BFU-5 MILLING MACHINE USING FINITE ELEMENT METHOD
35/35
CHAPTER V
BIBLIOGRAPHY:
5.1 REFERENCES:
i .Mechanical Engineering Design:Joseph Edward Shigley(MCGraw-Hill Book
Company).
ii.A Text Book Of Machine design:R.S Khurmi,J.K.Gupta(Eurasia publishing house
Pvt. Ltd)
iii.Design Of Transmission System:V.Jayakumar(Lakshmi publications,Nagapattinam
District,Tamil Nadu).
iv.Design Data:Faculty of Mechanical Engineering(PSG College Of
Technology,Coimbatore).
v.Design of Transmission elements:T.J.prabu
vi.Mechanical engineering design:Joseph E.Shigley ,Charles R.Misckke
5.2 WEBSITE
i.School.mech.uwa.edu.au
ii.Gizmology.net/gears.htm
iii.swiftdsl.com