1
TDEFNODEModeling block motions, fault locking, strain rates, transients
Use GPS velocities, displacements, time series, earthquake slip vectors, fault slip rates, InSAR
2
Acknowledgments
Funding: NSF, NASA, USGS, GNS Science
Routines: Chuck DeMets, Charles Williams, Steve Roecker, Bob King, W. Randolph Franklin, Dave Hollinger, Numerical Recipes
Debuggers: Dave Hollinger, Larry Baker
Guinea pigs (beta testers): Suzette Payne, Linette Prawirodirdjo, Laura Wallace, Zhang Zhuqi, and others
3
Download
web page, source
http://web.pdx.edu/~mccaf/www/defnode/
ppt, two examples
% ftp chandler.mit.eduLogin mitg, no pwd
cd incoming/workshop_miami
mget td*1117*
4
• Defnode - modeling steady motions only, use linear velocities
• Tdefnode - includes time-dependent motions and uses time series; data are time-sensitive
5
Motivation
• Velocity fields are superposition of multiple signals; rotations, strain rates, noise
• Time series showing strong non-linear (transient) effects
6
Not as scary as GAMIT
7
Field through mid 2009
Large-scale rotation with subduction locking superimposed
8
-0.06 deg/Myr
-0.25 deg/Myr
-0.39 deg/Myr
-0.15 deg/Myr
Calculate uniform strain and rotation rates in regions
Figure has block rotations removed from vectors
Courtesy of S. Payne
9
East component of continuous GPS site SAMP
mill
imet
ers
Non-linearity of time series is a major challenge.
2004 quake
2005 quakeAfterslip
Steady velocity
Afterslip from both events
The Sumatra quakes of 2004 and 2005, with afterslip
10
Block model can be used in non-steady state settings to separate kinemtics from transients.
In some cases the inter-event velocities are clear - short transients separated by long inter-event times.
Data from GNS Science
Data from PANGA
From McCaffrey 2009 GRL
11
Long-term velocity?
In other cases, it is difficult to see the steady site velocity through the transients.
Block models help by taking advantage of the spatial correlation among nearby sites
Data from GNS Science
12
TBLP
P566
Inter-event velocities are not independent
Parkfield quake
Data from PBO
13
Modeling estimated co-seismic offsets
2002 2009
14
Occurrence of earthquakes results in non-linear GPS time series.
We model the time series as a combination of the linear trend (kinematics) plus the steps from quakes.
Papua time series
15
Block model from inversion of GPS time series
Thrusting~17 mm/yrOblique
~11 mm/yrStrike-slip~10 mm/yr
Mountain building comprises only ~10% of the action
16
Yellowstone
17
InSAR (M. Aly)
18
Time series with sinusoidal term
InSAR data may overlap or have gaps in time
19
Multiple sill-like sources each with own time history
20
Complex GPS time series
Invert simultaneously with InSAR
21
22
Deformation analysis
Velocity field V(x,y) = [ Vx(x,y), Vy(x,y) ]
Solve for deformation gradient tensor:
dVx/dx dVx/dy
dVy/dx dVy/dy
Where:
Vx = x dVx/dx + y dVx/dy + Cx
Vy = x dVy/dx + y dVy/dy + Cy
23
The strain rate tensor is:
dVx/dx ½ (dVx/dy + dVy/dx)½ (dVx/dy + dVy/dx) dVy/dy
The vertical axis rotation rate is:
½ ( dVx/dy – dVy/dx )
This is done here in Cartesian coordinates (x,y) but can be done in spherical coordinates as well. TDEFNODE uses shperical coordinates (Savage).
24
25
Strain rates
Rotation rates
Not computed with TDEFNODE; butProgram is available.
26
Blocks
• Closed polygons on surface of Earth• Each characterized by angular velocity,
uniform strain rate• Bounded by faults, or pseudo-faults
27
Faults
• Surfaces dipping into the Earth described by nodes
• Separate blocks in three dimensions• Coincide with block boundaries at surface• Slip according to relative velocities of blocks• Have locking or not• Can have transients
28
Transients
• Spatial and time dependence types are specified
• Many types can be modeled - quakes, after-slip, slow-slip, volcanic
• Superimposed on long-term linear velocities
29
Data
• GPS velocities (East, North, Up)• GPS displacements (E, N, U)• GPS time series (E, N, U)• InSAR interferograms• Fault slip rates or directions• Earthquake slip vectors• Uplift rates or displacements (tidegauge, coral, etc.)
30
X is the position of the surface observation point,k represents the velocity component (x, y, or z),
RB is the angular velocity of the block containing the observation point relative to
the reference frame,
RG is the angular velocity of the GPS velocity solution containing the observation
point relative to the reference frame,is the horizontal strain rate tensor (X is the offset from strain rate origin)
HF is the Euler pole of the footwall block of fault relative to the hangingwall block,
N is the number of nodes along the fault,Qi is the position of node i,
i is the coupling fraction at node i,
Gjk (X, Qi) is the kth component of the response function giving the velocity at X due
to a unit velocity along fault at Qi in the jth direction on fault plane (downdip or
along strike)
GPS velocity vectors and uplift rates
Vk(X) = [ RG X ]k + [ RB X ]k + kkXk+klXl +
j=1,2 i=1,N [- HF Qi ]j i Gjk (X, Xi)
31
Other data typesTilt rates:
T(X) = [ Vz(X+X) - Vz(X - X) ] / (2 X )
(X is at the mid-point of the leveling line and X is the offset from the mid-point to the ends)
Slip vector and transform fault azimuths:
A(X) = arctan{[( HR - FR ) X]x / [( HR - FR ) X]y }
Geologically estimated fault slip rates or spreading rates:
R(X) = | ( HR - FR ) X |
32
Compiling
• TDEFNODE is written in fortran and has one C program to link
• Edit tdefcom1.h - set dimensions of arrays• Edit tdefiles.h - set filenames for earthquakes
and volcanoes to be included in profile lines• Edit Makefile provided, put in your compiler
names and flags• gcc and gfortran work fine• Put the executable file ‘tdefnode’ in your
path.
33
Control file
• All input information (except data files) are put in a file that the program reads at startup
• Each line has a 2-character key that signifies its purpose
• Key characters are in first two columns, followed by a colon :
• Order of lines does not matter
34
Models
• Model names are specified by MO: option and are 4-characters long
• The Control file can have multiple models using the MO: - EM: structure
• The model to run is selected in the command line:% defnode control_file model
35
Building the Blocks
Two options
1. Define all block outlines and faults separately
2. Program builds blocks from faults
36
Method 1. Define Blocks and Faults
Fault
Block
Use BL: to outline block;FA: to describe fault
37
Block boundaries are determined by seismicity, faulting, strain rates, … (reviewers always ask for justification of block boundaries).
38
Fault segmentBlock outline
• The block outline has the surface nodes and must coincide exactly with the fault surface nodes. • Not every edge of block has to be a defined fault.• But every fault must fall on a block edge.
39
Faults - defined by nodes
Nodes are in an irregular grid. Confined to depth contours.Designated by (longitude, latitude, depth).Subsurface nodes can be generated by program.
40
Representation of fault slip
• Nodes are specified along depth contours of fault
• Slip at each node is V, where ranges fromto and V is taken from poles
• Area between nodes is broken into small patches
• Surface deformation for each patch is determined and summed
Response (Green’s) functions are determined by putting unit velocity at one node and zero at all other nodes, then calculating the surface velocities by integration.
Pyramidical Bilinear
41
Half-space dislocation model (HSDM) to calculate surface deformation due to fault locking and slip events
42
Velocities from elastic strain rates arising from fault locking
surface
Locked fault
Free slipping
Use back-slip method to compute elastic deformation around locked fault.
Integrate over fault using small patches, can represent non-planar fault and non-uniform locking
43
Angular velocities - AV (Euler poles)• Each block has an AV assigned• Multiple blocks can have same AV, in which case there is no
fault between them• Long-term linear velocity V of each point in block is V = x r• AVs can be fixed or adjusted in inversion• Entered as Cartesian or Spherical coords, always units of
‘degrees per Million years’ and right-hand rule• PO: option to input AV• BP:, BC: options assign AV to blocks• PI: option to adjust AV in inversion
44
Strain Rate Tensors (SRT)• Each block may have uniform SRT assigned (optional)• May arise due to small faults within block (anelastic, permanent
deformation)• Multiple blocks can have same SRT (use common origin)• Long-term linear velocity V of each point in block is relative to
specified origin• SRTs can be fixed or adjusted in inversion• Entered as nanostrain per year (10-9 / year)
• Described by 3 components Exx, Eyy, Exy
• ST: option to input SRT and origin• BP: or BC: option to assign SRT to blocks• SI: option to adjust SRT in inversion
45
Strain Rate Velocities
Block
Origin (o, o)
Point (, )
46
Assign AV and SRT to Blocks
Block
Blk1
Blk2
Blk3
47
Method 2. Define Faults, Build blocks
Fault (extends to depth, can be locked)
Block
Set flag +mkbFA: to describe faultsBC: to identify blocks
Pseudo-fault (surface boundary, free-slip)
48
Region is divided into ‘blocks’, contiguous areas that are thought to rotate rigidly.
Each block rotates about a pole.
The rotating blocks are separated by dipping faults.
Velocities due to fault locking are added to rotations to get full
velocity field.
The relative long-term slip vectors on the faults
are determined from rotation poles.
Back-slip is applied at each fault to get surface
velocities due to locking.
49
The strain rate tensor near a locked fault represents a spatial transition from the velocity of one block to the velocity of the other. In other words, a locked fault allows one block to communicate information about its motion into an adjacent block.
50
Rotate velocity fields (or time series) into common reference frame.
Specify reference frame block with RE: option
Velocity fields are rotated to minimize velocities of sites on that block.
GI: option - list fields to be rotated
Does not require all velocity fields to have sites on reference block, since all velocity fields must agree on all blocks.
51
Total long-term (linear) velocities are the sum of the 4 terms:
• Velocity field rotation• Block rotation• Anelastic strain rate within block• Elastic strain rates from fault locking
52
Examples
• Update tdefnode - td_1116.zip
• Oregon - oregon_example.zip
• Costa Rica - cr_example.zip
53
Sample control file:
54
Run 1 - get poles and strain rates
55
Run 2: use PBO field, rotate into PNW field reference frame
56
Run 3: Multiple fields; strain rates, rotation rates and reference frames.
57
Reference frame adjustments for PNW1 and PBO.
58
--- Model input
These lines pertain for mod1, mod2, and mod3
--- First mo signals start of MO: - EM: structure
mo: mod1 mod2
These line pertain to mod1 and mod2
mo: mod1
These lines pertain to mod1 only
mo: mod2
These lines pertain to mod2 only
mo: mod3
These lines pertain to mod3 only
em: end of models
These lines pertain to mod1, mod2, and mod3
en: end of input
Models - a particular set of input parameters, designated by 4-char name. Multiple models can be in a single control file.
59
-- Fault input, blocks from faults
FA: for fault segments
-- For Fault1, it dips to east so start in south
Fa: Fault1 12 3 Blk2 Blk1 1 0 00.0 -90.0 30.0 -90.0 40.0Zd: 5 89Zd: 10 89
Blk1
-100, 30
-100, 40 -90, 40
-90, 30
-80, 40
-80, 30
Fault1
Blk2
-- If making blocks from faults, (+mkb flag) make pseudo-faults from remaining borders. They will be free-slip boundaries.
Fa: Blk1_bndry 24 1 Blk1 Blk1 1 0 00.0 -90.0 30.0 -80.0 30.0 -80.0 40.0 -90.0 40.0
Fa: Blk2_bndry 34 1 Blk2 Blk2 1 0 00.0 -90.0 30.0-100.0 30.0-100.0 40.0 -90.0 40.0
-- Give interior point of block to identify it, and specify pole and strain tensor for each
BC: Blk1 -95.0 35.0 1 0BC: Blk2 -85.0 35.0 2 0
All segments must end at another segment or an error occurs.
60
--- Block and Fault input
BL: for closed blocksFA: for fault segments
For Fault1, it dips to east so start in south
Fa: Fault1 12 3 Blk2 Blk1 1 0 00.0 -90.0 30.0 -90.0 40.0Zd: 5 89Zd: 10 89
Blk1
-100, 30
-100, 40 -90, 40
-90, 30
-80, 40
-80, 30
Fault1
Blk2
If inputting blocks, make polygon of borders of blocks. They will be free-slip boundaries.
BL: Blk1 1 04 -90.0 30.0 -80.0 30.0 -80.0 40.0 -90.0 40.0
BL: Blk2 2 04 -90.0 30.0-100.0 30.0-100.0 40.0 -90.0 40.0
-- BP: is alternative way to specify poles and strain tensors
BP: Blk1 1 0BP: Blk2 2 0
All block and fault points must coincide or an error occurs.
61
Nodes - slip or locking on nodes can be represented in several ways
x
z, w
Locking parameter is (x,z) or (x,w)
Independent nodes with or without smoothing; decreases down-dip; or is specified function of z
V-Boxcar-Gaussian-Exponential
is specified function of x,z- 2D Gaussian- Uniform Polygon
62
x
z, w
V
The fault below has 6 surface nodes and 5 downdip for a total of 30.For independent nodes (fault type FT: 0 or 1) we specify the inter-dependence of the nodes (NN:) and their starting values (NV:).
FT: 1 0NNg: 1 6 5 1 1 2 2 3 3 1 1 2 2 3 3 4 4 5 5 6 6 4 4 5 5 6 6 0 0 0 0 0 0
NV: 1 1.0 1.0 1.0 0.8 0.8 0.8
x
z
63
x
z, w
V
The fault below has 6 surface nodes, so 6 downdip ‘profiles’. For each one the function (z) can have different parameters. For example the function may be:
# DD Prof 1 2 3 4 5 6FT: 1 2 1 1 1PN: 1 1 1 2 2 3 3PV: 1 3 5.0 5.0 5.0 5.0 5.0 5.015.0 15.0 15.0
zu
zl
64
Downdip function 2 for variable , Zu = 6 Zl = 59 km
65
Types of downdip (1D) functions:
Exponential (Type 2)
Boxcar (Type 3)
Gaussian (Type 4)
Types of 2D functions:
Gaussian (Type 6)
Boxcar (Type 7)
Irregular polygon (Type 8)
Types of off-fault functions (not on block boundary)
Planar shear slip (Type 9)
Mogi (Type 10)
Planar expansion crack (Type 11)
66
Interseismic; I recommend locking the updip edge and forcing monotonic decrease in locking downdip
67
x
z, w
Locked nodes
Approximating ‘locking depth’; using downdip boxcar (FT: 3) fixing upper depth (0 km) and locking amplitude (1); solve for lower depth
Unlocked nodes# locking depth approx.FT: 1 3 0 0 1PN: 1 1 1 2 2 3PV: 1 3 1.0 1.0 1.0 0.0 0.0 0.0 15.0 15.0 15.0