8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 1/16
systems
www.z-systems.biz
Z-Look3
Evo SLM*
> P
r o d u c t C a t a l o g u e M a r c h 2 0 1 2
Experience and InnovationZ-Look3 implants – zirconia implants made of ZrO2 TZP-A HIP, proven in use over many years
S W I S S M A D E
C E R T I F I
CA T E
*Surface Laser Modified
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 2/16
New surface – all at a glance
˘Z-Look3 Evo SLM :: Implants
Z-Look3 Evo SLM is based upon the established, sand-
blasted surface Z-Look3. The modification of thesurface is achieved by a patented procedure (patent
pending). The material removal is realised by laser
technology and results in an enlargement of the
surface by increased macro- and micro-roughness.
The laser treatment on the thread flank follows the
thread lead (red marked area). This patented procedure
(patent pending) makes sure that the excellent
breaking strength of the Z-Look3 Evo implants stays
unaltered high.
Z-Look3 Evo rapide SLM, the next generation of
zirconia implants*Revolutionary surface technology
:: Unique laser modified surface (patent pending)
:: Increased surface roughness: SRa of Z-Look3 Evo SLM
rises by + 143 % from 1,49 µm to 3,62 µm in com-
parison to the sandblasted standard Z-Look3 Evo
surface
:: Based on clinical experience since 2004 with zirconia
implants (first placed in 2001)
* An extensive preclinical study is completed and
accepted for publication (JOMI / Journal of Oral and
Maxillofacial Implants)
2<
ystems
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 3/16
˘Z-Look3 Evo SLM :: Implants
Technology
Fig. 1 + 2 :: ESEM* picture of the peak of the thread flank.
The surface is sandblasted.
Fig. 3 + 4 :: ESEM* picture of the peak of the thread flank.
The surface is sandblasted and laser modified.
Fig. 1: Surface of Z-Look3 and Z-Look3 Evo implants (x 500) Fig. 3: New Surface of Z-Look3 Evo SLM implants (x 500)
Fig. 2: Surface of Z-Look3 and Z-Look3 Evo implants (x 2.000) Fig. 4: New Surface of Z-Look3 Evo SLM implants (x 2.000)
Roughness profile Z-Look3 Evo – ZrO2 sandblasted
P r o f i l h ö h e [ µ m ]
8
6
4
2
0
-2
-4
-6
-8
100 200 300 400 500 600 700 800
Profillänge [µm]
Mesurments: Alicona Infinte Focus IFM
Ra = 0.670µm
Roughness profile Z-Look3 Evo SLM – ZrO2 sandblasted and laser modified
Mesurments: Alicona Infinte Focus IFM
Ra = 3.10µm
P r o f i l h ö h e [ µ m ]
8
6
4
2
0
-2
-4
-6
-8
100 200 300 400 500 600 700 800
Profillänge [µm]
> 3
systems
* ESEM: Environmental Scanning Electron Microscope
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 4/16
Z3 Evo-40-10 SLM
:: Optimised possibilities of indication
thanks to new implant sizes withreduced shoulder width
:: Perfect individual aesthetics by
grindable preparation border*
:: Tapering thread with widened core
diameter in the upper part of the
thread for optimum mechanical
strength and better primary stability
:: A uniform CAD-CAM optimised conical
abutment for all standard implants
without insertion hexagon
:: Optimised insertion by large-surface
transmission of force on two parallel
surfaces:: Retention groove for holding tools and
accessories securely
:: Angulation and individualisation by
simple grinding*
M a g n i fi c a t i o n
> Implant 4 mm x 10mm
:: Revolutionary surface technology bypatented laser modified surface
(patent pending). Increased surface
roughness.
:: Improved self-tapping thread
:: Newly designed bone chip reservoir
ystems
4<
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 5/16
> 5
systems˘Z-Look3 Evo SLM :: Implants
The essentials at a glanceZ-Look3 Evo SLM
Z-Look3 Evo SLM :: Z-Look3 Evo SLM implants are based
on the experience of more than 20.000 Z-Look3 andZ-Look3 Evo implants made of ZrO2 TZP-A HIP, sold
since August 2004.
The new abutment has been designed uniformly for all
standard implants, an integrated retention groove en-
sures secure retention of the insertion tool and acces-
sory parts.
The insertion hexagon known from the Z-Look3
implant is not required. Occlusal grinding of the abut-
ment postoperatively is not necessary.
The variable implant insertion depth – due to counter-
sinking the implant shoulder to a differing depth –
does not apply. New insertion tools with improved
force transmission onto the abutment are available.
Excellent red-white aesthetics can be achieved by the
possibility of simple individual grinding* of the abutment
(preparation border and/or angulation).
Details of the proven thread design have been opti-
mised, the known implantation procedure has been
largely retained and the existing surgical tray can still
be used. Additional implant sizes and shoulder dia-
meters simplify selecting the right implant for difficultindications.
Impression caps, laboratory analogues and gingiva form-
ers simplify prosthetic handling.
* Z-System has had the manual grinding ability investigated for you by the renowned Fraunhofer Institute of Material Mechanics. The results show no
impairment in use of the ground Z-Look3 implants, manually ground implants have no increased risk of fracture. Z-Systems grinding procedure: use
exclusively red ring (47 µm) diamond instruments, maximum water cooling, working without pressure. Z-Systems will be pleased to make the results
available to you on request.
Z-Look3 Evo SLM implant/sectional drawing of abutment/sectional drawing of
abutment with angle piece adapter
Surface marked red shows the abutment area that must be ground for
an angulation of 20°, depending on implant diameter.
Gingiva former Impression cap
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 6/16
Material :: All Z-Look3 ceramic components are pro-
duced from zirconia (zirconium dioxide). However,
there is more than one grade of zirconia to choose
from. In the production of the components, the selection
of the raw materials as well as control during the
cleaning and production processes are extremely
important. Only leading manufacturers of dental
ceramic products are choosen as manufacturer of
Z-Look3 Evo SLM implants and components produced
from zirconia. They must meet Z-Systems’ quality cri-
teria. Depending on the requirements for the system
component, whether it is an implant, a cutting tool or
other surgical tool, the composition and the pro-
duction processes for the zirconia will vary.
Information about the different types of zirconia used
can be found with the descriptions of the individual
components.
Certification :: Medical devices from Z-Systems bear
the CE marking and are manufactured according to
the specifications of ISO 9001, ISO 13485, as well as
MDD 93/42/EEC.
Z-Systems is registered with the US Food and Drug
Administration (FDA).
An overview of the Z-Look3 implant system features:
:: Implants and surgical instruments are produced
from zirconia.
:: The Z-Look3 implant system enables completely
metal-free treatment.
:: Four different one-piece implant designs for a broad
range of indications.
:: Abutments easily modifiable, no specific prosthetic
parts required.
:: The design and material allow the prosthetic pro-
cedure and treatment to be carried out in a similar
manner as for natural teeth. The abutments can be
ground easily in the mouth.
:: The implant design is ideal for treatment withCAD-CAM prosthodontics.
:: The design allows compensation of implant diver-
gences of up to 20º (by simple intraoral grinding).
Many people are satisfied with what is available. We are
not. Many follow the maxim: no experiments. We have
successfully tested our implants. That is why Z-Systems
is here today: We develop and produce metal-free solu-
tions in dental implantology made from high perfor-
mance special ceramics. Certified and approved: white
aesthetics thanks to zirconia (zirconium dioxide).
6<
˘Z-Look3 Evo SLM
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 7/16
> 7
systems
Implants
Material :: All zirconia implants are produced from
ZrO2 TZP-A HIP bioceramics according to ISO 13356. This
material has been in use for a long time in the pro-duction of hip joint prostheses. Among other things,
the material reaches its bending strength, which is
much higher than with commonly used titanium, due
to the «Hot Isostatic Post Compaction» process. The
material is reprocessed after the sintering process by
being further compacted in industrial furnance for
three days at 2000 bar, which significantly improves
the physical characteristics of the base material.
Indications :: Z-Look3 Evo SLM implants are designed
for surgical implantation into the upper and lower jaw
for the attachment of prosthodontic appliances to
replace missing teeth.
Osseointegration and healing time :: The unique pat-
ented (patent pending) laser modified Z-Look3 Evo SLM
surface has an increased surface roughness.
Due to the one-piece design, the implants must be
protected from load during healing. Longterm tempo-
raries, protective splints or hollowed out interim pros-
theses can be used for this purpose. A healing time ofthree months for the lower jaw and six months for the
upper jaw is recommended.
Note :: Please note our detailed instructions for sur-
gical and prosthetic procedures.
Insertion. The prerequisites :: Sufficient bone quantity
must be available. The thread must be covered by at
least 1 mm of healthy bone. Simultaneous sinus floorelevation with implantation is only indicated if there is
at least 7 mm of remaining bone available in the ver-
tical dimension. The Z-Look3 Evo SLM implants are
selftapping. For bones in category D1/D2 or hard cor-
tical bone, pre-cutting with appropriate tap is recom-
mended. When inserting the implant, we recommend
a torque of 35 Ncm.
Implant characteristics – an overview
:: The abutment can be ground in the same way as
natural teeth. Special care should be taken with the
treatment protocol i.e. red diamond, max. red hand
piece rotational speed, max. water cooling and low
pressure.*
:: One-piece design, therefore no microgap, reduces the
possibility of bone loss.
:: The apical part of the implant is conical to improve
introduction into the cavity.
:: The star-shaped apical cut-out serves to receive bone
chips.
:: The rounded thread prevents tension and notchingeffects.
:: The implant can be inserted manually or with the
angle piece.
:: Implants can be inserted further or unscrewed even
after the abutment is modified.
:: The wide implant shoulder enables compensation of
implant divergence of up to 20º.
˘Z-Look3 Evo SLM :: Implants
* Z-System has had the manual grinding ability investigated for you by the renowned Fraunhofer Institute of Material Mechanics. The results show no
impairment in use of the ground Z-Look3 implants, manually ground implants have no increased risk of fracture. Z-Systems grinding procedure: use
exclusively red ring (47 µm) diamond instruments, maximum water cooling, working without pressure. Z-Systems will be pleased to make the results
available to you on request.
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 8/16
8<
ystems
Z3 Evo-36-10 SLM ø 3.6 mmø shoulder 4.6 mminsertion depth 10 mm
With reduced threaddiameter and reducedlength, especially for lim-ited alveolar ridge widthwith reduced vertical
bone availability.Upper jaw:lateral incisors,lower jaw: central/lateral incisors.Not suitable for ::– Upper jaw:central incisors– Upper/lower jaw:canines, premolars andmolars as well asbridge restoration.
fig. 1
Z-Look3 Evo SLM implants are currently available in the following dimensions:
˘Z-Look3 Evo SLM :: Implants
Z-Look3 Evo SLM :: is available in various lengths and dia-
meters.
Please note :: In the selection of implant length, the
excess length of the drill (drill tip = max. 1.3 mm) must
always be taken into consideration. (See sketch on page 10).
Implant configurationsIn lengths and diameters
Z3 Evo-36-11 SLM ø 3.6 mmø shoulder 4.6 mminsertion depth 11.5 mm
With reduced thread di-ameter, especially for lim-ited alveolar ridge widthwith sufficient verticalbone availability.
Upper jaw: lateral incisors,lower jaw: central/lateral incisors.Not suitable for ::– Upper jaw:central incisors– Upper/lower jaw:canines, premolars andmolars as well asbridge restoration.
Z3 Evo-40-08 SLM ø 4 mmø shoulder 4.8 mminsertion depth 8 mm
Suitable for mostindications with reducedvertical bone availability.
Z3 Evo-40-10 SLM ø 4 mmø shoulder 4.8 mminsertion depth 10 mm
With standard threaddiameter for universaluse in the upper andlower jaw.
Z3 Evo-40-11 SLM ø 4 mmø shoulder 4.8 mminsertion depth 11.5 mm
With standard threaddiameter for universaluse in the upper andlower jaw.
Z3 Evo-40-13 SLM ø 4 mmø shoulder 4.8 mminsertion depth 13 mm
With standard threaddiameter for universaluse in the upper andlower jaw with especiallygood vertical bone.
fig. 6 fig. 5 fig. 4 fig. 3 fig. 2
8<
ystems
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 9/16
> 9
systems˘Z-Look3 Evo SLM :: Implants
Our implant system is manufactured from zirconia ZrO2 TZP-A HIP.
Z3 Evo-50-08 SLM ø 5 mmø shoulder 6 mminsertion depth 8 mm
With enlarged threaddiameter, particularlysuitable for wide alveolarridges with reduced verti-cal bone availability.
fig. 7
Z3 Evo-50-10 SLM ø 5 mmø shoulder 6 mminsertion depth 10 mm
With enlarged threaddiameter, especially forwide alveolar ridges.
fig. 8
Z3 Evo-50-10R SLM ø 5 mmø shoulder 5.4 mminsertion depth 10 mm
With reduced shoulderdiameter for use withgood bone availabilityand narrow interdentalspace, particularly in
the premolar-/anteriorregion.
fig. 9
Z3 Evo-50-11 SLM ø 5 mmø shoulder 6 mminsertion depth 11.5 mm
With enlarged threaddiameter, especiallyfor wide jaws, withparticularly good verticalbone availability.
fig. 10
Z3 Evo-50-11R SLM ø 5 mmø shoulder 5.4 mminsertion depth 11.5 mm
With reduced shoulderdiameter, for use withparticularly good verticalbone availability and re-duced interdental space,
especially in the premo-lar-/anterior region.
fig. 11
Z3 Evo-50-13 SLM ø 5 mmø shoulder 6 mminsertion depth 13 mm
Due to its length andits diameter, especiallysuitable as immediateimplant* in the upperanterior jaw and the
cuspids.
fig. 12
> 9
systems
Ideal implant selection for Z-Look3 Evo SLM
(with respect to thread diameter) ::
Left illustration: upper jaw
Right illustration: lower jaw
4 :: Ø 4 mm = 4.8 mm shoulder Ø
5 :: Ø 5mm = 6mm shoulder Ø
5R :: Ø 5 mm = 5.4 mm shoulder Ø
3.6 :: Ø 3.6 mm = 4.6 mm shoulder Ø
3.6
4/5R
4/5R
5
55
5
3.6
3.6
4/5R
4/5R
4/5R
4/5R
4/5R
* see http://www.eao.org/conference/past
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 10/16
10<
ystems
M a g n i fi c a t i o n
Z-Tools :: Surgical instruments
Implant Depth Gauge
Z3 Evo-40-11 SLM TZ-DP220Z3-TD325
Drill
max. 1.3 mm
10 mm
15 mm
8 mm
6 mm
11.5 mm
13 mm
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 11/16
> 11
systems
Material :: The cutting instruments are made from
high-tensile ATZ high-performance ceramic (AluminaToughened Zirconia). This aluminium oxide reinforced
zirconia is ideal for the production of drills and taps.
The instruments have excellent cutting performance
and lifetime.
Characteristics of the surgical instruments:
:: Cutting instruments are produced from high-tensileATZ high-performance ceramic.
:: The instruments have excellent cutting perfor-
mance and lifetime.
:: Can be autoclaved up to 20 times at 134ºC standard
programme.
:: Recommended drill speeds for preparing the implant
bed: 400 to 800 rpm.
:: Disinfection with commercially available products.
:: Easily visible depth markings.
˘Z-Tools :: Surgical Instruments
Surgical/cutting instrumentsMetal-free implantology begins with the instruments
fig. 13
Surgical tray Fully equipped surgical tray
Contains :: round drill 2.3 mm x 16 mm,twist drill 2.3 mm x 16mm, twist drill 2.85 mm x 16 mm,twist drill 3.25 mm x 16 mm, twist drill 3.75 mm x 16 mm,twist drill 4.25 mm x 16 mm, tap 3.6 mm, tap 4 mm, tap 5 mm,scalpel no. 12, scalpel no. 15, periosteal elevator,depth gauge 2.2 mm x 20 mm, mandrell,*ratchet adapter 10 mm, *ratchet adapter 20 mm,*angle piece adapter 8 mm, **ratchet adapter 16 mm,**ratchet adapter 24 mm, **angle piece adapter 12 mm,
angle piece extension, torque ratchet.
*Adapters with black O-ring receive the taps.**Adapters with white O-ring are used for insertion of Z-Look3 Evo SLM i mplants.
Autoclavable at 134ºC
standard programme.
Note :: Please pay attention to our
detailed instructions for surgicaland prosthetic procedures as well
as to the instructions for care andmaintenance of Z-Look instruments.
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 12/16
12<
ystems ˘Z-Tools :: Surgical Instruments
Drills :: The drills are three-fluted (low in vibrations)
and have a maximum overlength of 1.3 mm. Themarkings on the drills correspond to the insertion
depths of 6, 8, 10, 11.5, 13 and 15 mm. The drills are all
equal in length and can be extended with the angle
piece extension.
Tap :: The implants are self-tapping for bone classes D3
– D4. For bone class D1 – D2 or hard cortical bone, thetap must be used. When inserting the implant, we rec-
ommend a torque of 35 Ncm for the implants in order
to avoid placing too much pressure on the bone. The
taps can be used with the ratchet or the angle piece.
Corresponding adapters are available in a variety of
lengths.
Z3-RD230
Round drill2.3 mm x16 mm
For marking
the implant
position
Z3-TD230
Twist drill2.3 mm x16 mm
For length and
pilot drilling
Z3-TD285
Twist drill2.85 mm x16 mm
For the final
drilling of
the 3.6 mmimplant bed
Z3-TD325
Twist drill3.25 mm x16 mm
For the final
drilling of
the 4 mmimplant bed
Z3-TD375
Twist drill3.75 mm x 16 mm
For the final
drilling of
the 5 mmimplant bed
Z3-TD425*
Twist drill4.25 mm x16 mm
*Optional drillfinal crestal
osteotomy ofthe 5.0 mmimplant bedfor bone class
D1/D2
fig. 14 fig. 15 fig. 16 fig. 17 fig. 18 fig. 19 fig. 20 fig. 21 fig. 22
The versions of the drills Tap design
Z3-T360
Tap3.6 mm
For all 3.6 mm
implants
Z3-T400
Tap4 mm
For all 4 mm
implants
Z3-T500
Tap5 mm
For all 5 mm
implants
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 13/16
> 13
systems˘Z-Tools :: Surgical Instruments
Auxiliary surgical instrumentsMetal-free implantology begins with the instruments
Scalpels, periosteal elevator :: Due to their complex
shape, these instruments are produced from zirconiausing the injection molding process. These instru-
ments must be handled carefully, since it is possible
that they may break if subjected to a hard blow. There
is no risk of breakage during normal use.
ZT-SC12
Scalpel No. 12
Zirconia,12 mm blade
ZT-SC15
Scalpel No. 15
Zirconia,15 mm blade
ZT-PE
Periostalelevator
Zirconia
fig. 24 fig. 25 fig. 23
Auxiliary surgical instruments
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 14/16
14<
ystems ˘Z-Tools :: Auxiliary Surgical Instruments
Depth gauge :: The depth gauge is produced from ATZ
high-performance ceramic (Alumina Toughened Zir-conia) and is used to verify the drilling axis as well as
for X-ray depth measurement for Z-Look3 Evo SLM
implants.
Inserting instruments and ratchet :: The inserting ins-
truments (ratchet- and angle piece adapters) and torqueratchet are made from stainless steel.
Auxiliary surgical instruments Metal-free implantology begins with the instruments
Auxiliary surgical instruments
ZT-HE18
Angle pieceextension
Stainless steel,
extension of theangle piece shaft
ZT-DP220
Depth gauge2.2 mm x 20 mm
ATZ high-perfor-
mance ceramic,verification of the
drilling axis as wellas X-ray depthmeasurement for
Z-Look3 Evo SLMimplants
ZT-MD
Mandrell
Stainless steel,
accepts angle pieceadapter
fig. 26 fig. 27 fig. 29 fig. 28
ZT-HA8
Angle pieceadapter
Stainless steel,
receives the taps
fig. 32
ZT-RA20-8
Ratchet adapter20mmreier Stahl,Stainless steel,
receives and ex-tends the taps
ZT-RA10-8
Ratchet adapter10mm
Stainless steel,
receivesthe taps
fig. 31
TR35
Torque ratchet reier Stahl,Stainless steel,
receives the ratchetadapters
fig. 30
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 15/16
> 15
systems
Insertion instruments :: The insertion instruments for
Z-Look3 Evo SLM implants are not compatible with
Z-Look3. They are manufactured from stainless steel
and may be differentiated by the white colour of the
O-ring.
Accessories :: Impression caps, lab analogues and gingiva
formers are suitable only for unground Z-Look3 Evo SLM
abutments.
Insertion instruments and accessoriesFor Z-Look3 Evo SLM implants
˘Z-Look3 Evo SLM :: Evo
fig. 35
ZT Evo-RA24
Ratchet adapter24 mmreier Stahl,Stainless steel,for insertion of Z-Look3Evo SLM implants
with the torque ratchet
fig. 33
ZT Evo-HA12
Angle piece adapter
Stainless steel,for insertionof Z-Look3 Evo SLM
implantswith the angle piece
ZT Evo-RA16
Ratchet adapter16 mm
Stainless steel,for insertion of Z-Look3Evo SLM implants
with the torque ratchet
fig. 34 fig. 36
ZT-I36
ZT-I40
ZT-I50
ZT-I50R
Impression capreie
X-ray opaque PEEK
fig. 37
ZT-L36
ZT-L40
ZT-L50
ZT-L50R
Laboratory analogue
Titanium, each sizecolour-coded
fig. 38
ZT-G36
ZT-G40
ZT-G50
ZT-G50R
Gingiva formerreier Stahl,
X-ray opaque PEEK
8/13/2019 Teeth implant non metallic
http://slidepdf.com/reader/full/teeth-implant-non-metallic 16/16
Phone +41 (0)62 388 69 69
Fax +41 (0)62 388 69 70
Mail [email protected]
W b t bi
Headquarter
Z-Systems AG
Bittertenstrasse 15
CH-4702 Oensingen
S it l d
You and us
Z-Systems for users
Become a user :: To assure the correct use of Z-Look3
Evo SLM implants, Z-Systems sells Z-Look3 Evo SLM im-plants only to qualified users.
Dentists and implantologists who – apart from mem-
bership in a professional implantological association –
fulfil at least two of the following conditions can
become qualified:
:: Regular participation in Z-Look3 further training
events
:: Participation in implantological further training
courses
:: Implantological experience
:: Implantology as main area of activity
:: Acceptance of the support of an experienced
user of Z-Systems
Internet www.z-systems.biz :: There is a multitude of
information about Z-Systems available to you: detailed
product information, literature, presentations, training,
research results as well as patient cases of many treat-
ments which have thus far been carried out with
Z-Look3.
Z-Training :: Share experience and learn from and with
colleagues – Z-Systems offers its users and anyoneinterested extensive options for continuous profes-
sional development. Z-Look3 courses are offered with-
and without live surgeries. All information about
our courses can be found under «News» on our web
page or contact the Z-Systems service centre directly.
Personal visits :: Z-Systems has a customer service
team covering all of Germany and Switzerland and
is represented in the international market by selected
distributors. We will be pleased to advise you individ-
ually through our service hotline for Switzerland and
internationally +41 62 388 69 69.
www.z-systems.biz
˘Z-Systems :: User Information
Phone 1-877-874-9407
Fax 1-781-754-6565
Mail [email protected]
W b t bi
USA
Z-Systems USA, Inc.
284 Monponsett Street,
Suite 208
H lif M 8