8/12/2019 The Mo Dynamics
1/20
8/12/2019 The Mo Dynamics
2/20
Volumetric Properties of Pure Fluids
The three-dimensional p
v
T surface is useful for bringing out thegeneral relationships among the three phases of matter normally
under consideration. However, it is often more convenient to work
with two-dimensional projections of the surface.
pvT sur face and projections for a substance that expands on f reezing
Three-dimensional view.
8/12/2019 The Mo Dynamics
3/20
PT Diagram for a pure Substance
If the pvT surface is projected onto the pressuretemperature plane, a
property diagram known as a phase diagram resul ts. As shown in F ig., when the
surface is projected in this way, the two-phase regions reduce to lines. A point on
any of these lines represents all two-phase mixtures at that particular temperatureand pressure.
The triple line of the three-dimensional pvT surface projects onto a point on
the phase diagram. This is called the tr iple point.
The line representing the two-phase solidliquid region on the phase diagram
slopes to the left for substances that expand on freezing and to the right for those
that contract.
The term saturation temperature designates the
temperature at which a phase change takes place at
a given pressure, and this pressure is called the
saturation pressurefor the given temperature. It isapparent from the phase diagrams that for each
saturation pressure there is a unique saturation
temperature, and conversely.
8/12/2019 The Mo Dynamics
4/20
Phase diagram for water
The temperature assigned to the triple point of water is 273.16 K.
The measured pressure at the triple point of water is 0.6113 kPa.
8/12/2019 The Mo Dynamics
5/20
PV Diagram
On PV diagram the boundaries of PT diagram are areas i.e., regions where twophases, solid/ liquid, solid/ Vapour, and liquid/vapour co exist in equilibrium.
The triple point here becomes a horizontal line, where the three phases co-exist
at a single a single temperature and pressure.
Fig shows a PV diagram, with 3 isotherms
super imposed. the line labeled T
8/12/2019 The Mo Dynamics
6/20
The horizontal segments of the isotherms in the 2-phase region become
progressively shorter at higher temperatures, being ultimately reduced to apoint at C, thus the critical isotherm labeled Tc exhibits a horizontal inflection
at the critical point C at the top of the dome. Here the liquid and vapour phases
cannot be distinguished from each other, because their properties are the same.
At the top of the dome, where the saturated liquid and saturated vapor lines
meet, is the cri tical point. The critical temperature Tc of a pure substance is
the maximum temperature at which liquid and vapor phases can coexist inequilibrium. The pressure at the critical point is called the critical pressure, pc.
The specific volume at this state is the critical specific volume.
8/12/2019 The Mo Dynamics
7/20
Sketch of a temperaturespecif ic volume diagram for water
showing the liquid, two-phase liquidvapor, and vapor regions
TemperatureSpecific volume diagram
8/12/2019 The Mo Dynamics
8/20
SATURATION TABLES
The saturation tables are a list property values for the saturated liquid and
vapor states. The property values at these states are denoted by the subscripts fand g, respectively. (ref tables)
The specific volume of a two-phase liquidvapor mixture can be
determined by using the saturation tables and the definition of quality given by,
The total volume of the mixture is the sum of the volumes of the liquid
and vapor phases
V= Vliq+ V vap
Dividing by the total mass of the mixture, m, an average specific
volume for the mixture is obtained
8/12/2019 The Mo Dynamics
9/20
Since the liquid phase is a saturated liquid and the vapor phase isa saturated vapor, Vliq =mliq vfand V vap = mvapvg, so
by the definition of quality, x= mvap /m, and noting that
mliq/m =1- x, the above expression becomes
8/12/2019 The Mo Dynamics
10/20
8/12/2019 The Mo Dynamics
11/20
8/12/2019 The Mo Dynamics
12/20
Generalized Compressibility Chart
UNIVERSAL GAS CONSTANT, R
Let a gas be confined in a cylinder by a piston and
the entire assembly held at a constant temperature. Thepiston can be moved to various positions so that a series of
equilibrium states at constant temperature can be visited.
Suppose the pressure and specific volume are measured at
each state and the value of the ratio is volume per mole
determined. These ratios can then be plotted versus pressureat constant temperature. The results for several temperatures
are sketched in Fig. When the ratios are extrapolated to zero
pressure, precisely the same limiting value is obtained for
each curve. That is,Sketch of PV/T versus pressur e
for a gas at several specif ied
values of temperatur e.
If this procedure were repeated for other gases, it would be found in every instance that
the limit of the ratio as p tends to zero at fixed temperature is the same, namely Since the
same limiting value is exhibited by all gases, is called the universal gas constant. I ts
value as determined experimentally is
R 8.314 kJ/kmol . K
8/12/2019 The Mo Dynamics
13/20
COMPRESSIBILITY FACTOR, Z
The dimensionless ratio is called the compressibil i ty factor and is denoted by Z.
That is,Z=pv/RT
Vari ation of the compressibil ity factor of hydrogen
with pressur e at constant temperature.
8/12/2019 The Mo Dynamics
14/20
8/12/2019 The Mo Dynamics
15/20
EQUATIONS OF STATE
Considering the curves of two fig. (refer slide 12 & 13), it is reasonable to think
that the variation with pressure and temperature of the compressibility factor forgases might be expressible as an equation, at least for certain intervals ofp and
T. Hencce we can write Two expressions.
1. One gives the compressibility factor as an infinite series expansion in
pressure:
where the coefficients depend on temperature only. The dots in Eq. represent
higher-order terms. The other is a series form entirely analogous to Eq. 3.29 but
expressed in terms of Volume V instead ofP
These Equations are known as vir ial equations of state, and the coeff icients
andB, C, D, . . . are called virial coefficients.
8/12/2019 The Mo Dynamics
16/20
Equations of state can be classified by the number of adjustable constants they
include. Let us consider some of the more commonly used equations of state in
order of increasing complexity
1. Two-Constant Equations of State
a. VAN DER WAALS EQUATION
An improvement over the ideal gas equation of state based on elementary
molecular arguments was suggested in 1873 by van der Waals, who noted that
gas molecules actually occupy more than the negligibly small volumepresumed by the ideal gas model and also exert long-range attractive forces on
one another.
Based on these elementary molecular arguments, the van der Waals equation
of state is
The constant b is intended to account for the finite volume occupied by the
molecules, the term accounts for the forces of attraction between molecules,
and is the universal gas constant. Note than when a and b are set to zero, the
ideal gas equation of state results.
8/12/2019 The Mo Dynamics
17/20
b. REDLICHKWONG EQUATION
The RedlichKwong equation, considered by many to be the best of the two-
constant equations of state, is
8/12/2019 The Mo Dynamics
18/20
Internal Energy, Enthalpy, and Specific Heats of Ideal Gases
For a gas obeying the ideal gas model, specific internal energy depends only ontemperature. Hence, the specific heat cv is also a function of temperature alone.
That is,
This is expressed as an ordinary derivative because u depends only on T.
By separating variables
On integration
8/12/2019 The Mo Dynamics
19/20
For a gas obeying the ideal gas model, the specific enthalpy depends only on
temperature, so the specific heat cp, is a function of temperature alone.That is
Separating variables
On integration
8/12/2019 The Mo Dynamics
20/20
An important relationship between the ideal gas specific heats can be developed
by differentiating Eq. with respect to temperature
and introducing Eqs. for dh& duto obtain
On a molar basis, this is written as
For an ideal gas, the specific heat ratio, k, is also a function of temperature only
and