TLA-101 LINE ARRAY SYSTEM
Exterior design and specifications are subject to change without notice.
Add The third Industry District, Wentang Dongcheng,
Dongguan, Guangdong Province, 523121 China
Tel +86 (0)769 22024612 22024613
Fax +86 (0)769 22665939 22263072
ELDER AUDIO MANUFACTURE CO.,LTD
Http:www.elderaudio.com
TLA -101 is a line array loudspeaker for medium
scale sound reinforcement.
Using the TLF-101 Flying Frame it can be flown
in vertical columns with up to 12 cabinets giving
a 90 constant dispersion pattern in the
horizontal plane.
TLA-101 is a 2-way design housing 2 10"
neodymium kapton LF drivers and 2 4" 1"
(101.6 25.4 mm) neodymium kapton wave planar
compression drivers.
The cylindrical wave segments of each cabinet
will couple without gabs and sum up coherently.
Splay angles between adjacent cabinets can be
set in the range from 0 to 5 .
LINE ARRAY SYSTEM
TLA-101 System is driven by modular power amplifier AP-4U or AM-4U with analog or digital control cards.
All components are arranged symmetrically around
the centre axis of the cabinet to produce a perfect
symmetric dispersion pattern. This set up allows a
very smooth crossover design with well defined
overlap of adjacent frequency bands resulting in a
very consistent and accurate horizontal dispersion.
Due to dipolar arrangement of the LF drivers the
nominal dispersion of 90 is maintained down to
200Hz.
| 2 |
TLA-101 frequency response extends from
90 Hz to above 18KHz.
TLA-101 cabinet is constructed of plywood and
has impact and weather resistant polyurethane
finish. The front of the loudspeaker cabinet is
protected by a rigid metal grill.There are two
handles in the side panels.All necessary rigging
components are mounted to the cabinet.
Up to 6 pieces of TLA-101 cabinets can be
stacked and interlinked by using the standard
TLA rigging components and the TLF-101 flying
frame for ground support.
TLA-101
Ratent No.200630061267.8
H I G H - T E C H F O R Y O U R L I S T E N I N G E N J O Y M E N T
1pcs
2pcs
8pcs
8pcs
2pcs
1pcs
1pcs
1pcs
6pcs
1pcs
1pcs
3pcs
10pcs
4pcs
1pcs
2pcs
4pcs
4pcs
4pcs
6pcs
1pcs
2pcs
2pcs
1pcs
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Case
MF/ LF Neodymium Kapton driver
Screw
Screw
Neodymium Kapton driver
Bolt
Back holder left
Splay link
Screw
Back holder right
Self-locking Nut
Locking pins
Screw
Screw
Terminal board
Connector
Shim
Cushion shim
Nut
Screw
Front link right
Front grill
Screw
Front link left
Plywood 18mm 12-laminate
10"
H/H5 30M D=8.2-8.7
P/H5 40M D=9
4" planar wave driver
M10 136mm
TLA-101
TLA-101
B/H5 25M D=10
TLA-101
M10 self-locking
11.8 65mm
T/H4 12A
3 12KM
TLA-101(160 100 2)
NEUTRIK NL4MPR
M3 washer
M3 spring
M3 Nut
K/H5 25M
TLA-101
TLA-101
T/H4 25A
TLA-101
| 3 |
ASSEMBLY DIAGRAM
| 4 |
This calculation software is used to calculate the
flying parameters for TLA-101 Line Array system.
It can automatically calculate parameters such
as splay angle between cabinets, number of
loudspeakers needed, flying point position, etc.
according to various application requirements in
different venues.
LINE ARRAY CALCULATION SOFTWARE
| 6 |
MIX FOHOUT LEFT OUT RIGHT
AMP 1 AMP 2
AMP 3
CONNECTION EXAMPLE WITH AP-4U AND AM-4U
Frequency response
Sensitivity( 1m / 1 W)
Dispersion
Nominal impedance LF
Nominal impedance HF
Power handling capacity LF
Power handling capacity HF
55 Hz-18 kHz
104 dB single cabinet
90 10
8/16 ohms
8/16 ohms
400W/1900W peak 10 ms
80W/450W peak 10 ms
SPECIFICATIONS
| 5 |
LF 2 x 10" neodymium driver
HF 2 x 4"x 1" 101.6 x 25,4 mm neodymium
Kapton planar wave drivers,max.SPL: 133 dB
COMPONENTS
TLA-101 loudspeakers are mechanically connected
using a three-point suspension system.
This consists of the TLF-101 flying frame from
which the cabinets are suspended using rigging
links and pins located on both front sides of the
cabinet and a central rear splay link.
The rear splay link allows quick and easy selection
of vertical angles between cabinets.
These are all permanently attached to the cabinets.
TLF-101 flying frame is a welded steel frame
designed to suspend a maximum of 12 pieces of
TLA-101cabinet.
TLA-101
THREE POINT SUSPENSION SYSTEM
The advantage of handling things in this way is
quite obvious. Using the control modules provides
the opportunity to set up a very compact sound
reinforcement system, individually matching a
particular application .Cable length and connecting
labour can be reduced to the minimum.
There are two AC circuit breakers on the rear panel
of AP-4U or AM-4U. If the switch shuts off automatically
on normal using condition, push it back to the ON
position. No fuses are used.
AP-4U and AM-4U are remote-controllable with the digital
control card and therefore construct the platform for 3
PA systems.
A wide range of analog modules with individual
functions are available. With these modules
signal processing which is normally realized by
external equipment can be integrated into the
power amplifier.
The module slots inside the front panel of the
AP-4U or AM-4U power amplifier make it easy
and convenient to insert or take out analog or
digital control card.
AP-4U and AM-4U are 4 channel modular power
amplifiers and the most flexible solution for any
mobile and permanent installation application.
The RMS power output of AP-4U is 1200W/8
per channel.
There is one mute switch with indicator for each
channel on the front panel of AP-4U or AM-4U.
AP-4U&AM-4U
MODULAR POWER AMPLIFIER
Ratent No.200630061266.3
AP-4U
AM-4U
| 8|| 7 |
AP-4U
AM-4U
Power 4 channel mode
4 channel mode
THD
Inter modulation distortion
Frequency response
Phase deviation
Damping factor
Crosstalk
S/N ratio
Total gain
Error of channel gain
Input sensitivity
Slew rate
Input impedance
Input connectors
Output connectors
Cooling
Controls on front panel
Controls on back panel
Indicator on front panel
Amplifier protection
Dimensions(W D H)
Power supply
Weight
8 4 1200W peak 4 3000W
4 4 1800W peak 4 5000W
<0,1% 20Hz-20KHz
<0,5% (f = 60Hz/7KHz, 4:1) on normal working condition
20Hz - 20KHz ( 0,25dB)
<15
> 600 20Hz-400Hz
-75dB
>105dB
40 0.5dB
<0.25dB
1V
>100 V/ s
Unbalanced:10K ; Balanced:20K
3-pin XLR Neutrik
Speakon NL4 MP
two fans, brushless , stepless shifting speed control
4 mute button
2 circuit breaker
4 mute indicator
DC /overload/overheat/protection etc.
483 452 178mm
AC 220V-230V, 50Hz 60Hz, 1500VA
40Kg
| 10 |
SPECIFICATIONS
The connection cable for AP-4U or AM-4U
is alternative with one open end or with a
32 A 3-pole CEE standard plug available.
Cleaning the filters system is simple
without demounting the amplifier from
the rack. AP-4U is equipped with two
independent brushless and stepless
fans working with automatic speed-control
function. The air circulation is front-to-rear,
allowing trouble-free operation even in
smaller power amplifier rack systems.
Also the mechanic construction and
manufacturing guarantee is the highest precision.
The robust and highly rigid steel chassis
is meant to survive the extensive wear
of touring applications.
| 19 |
With a peak output of 12 KW AP-4U can be equipped
for driving woofers .Fo r example AP-4U can be
attached to up to eight pieces of T18W and form the
bass foundation for Line Array TLA-101 or ONAX PA
System.
AP-4U or AM-4U has various application possibilities
by mixing different control cards. For example, AP-4U
or AM-4U with properly chosen mixed modes of control
cards can be used to drive TLA-101 Array System or
T12L and T18W clusters.
MODULAR POWER AMPLIFIER
AP-4U
Power 4 channel mode
4 channel mode
THD
Intermodulation distortio
Frequency response
Phase deviation
Damping factor
Crosstalk
Signal to noise ratio
Total gain
Error of channel gain
Input sensitivity
Slew rate
Input impedance
Input connectors
Output connectors
Cooling
Controls on front panel
Controls on back panel
Indicator on front panel
Amplifier protection
Dimensions(W D H)
Power supply
Weight
| 12 |
SPECIFICATIONS
| 11 |
MODULAR POWER AMPLIFIER
8 4 0-220W,A/B Mode,200-750W H Mode
8 4 0-220W,A/B Mode,200-1200W H Mode
<0,1% 20Hz-20KHz
<0,5% (f = 60Hz/7KHz, 4:1
on normal working condition)
20Hz - 20KHz ( 0,25dB)
<15
> 600,20Hz-400Hz
-75dB
>105dB
40dB( 100)
<0,25dB
0.775V
>103V/ s
10K /Unbalanced:10K ; Balanced:20K
8pcs,3-pin XLR Neutrik
4pcs,Speakon NL4 MP
two fans, brushless,stepless speed control
4 mute button
2 circuit breaker
4 mute indicator
DC/overload/overheat/protection etc.
483 452 178mm
AC 220V-230V, 50Hz 60Hz, 1500VA
36Kg
AM-4U works with the same control modules as the
AP-4U. When power rating is under 200W this
amplifier works in class A/B mode.
AM-4U is an ideal amplifier for tops of TLA-101or
ONAX tops . Also various bi-amp mode applications
or monitoring system on the stage is not a problem
for the amplifier. Like AP-4U AM-4U is also a
4-channel amplifier and equipped with two power
supplies.
The connection cable for AM-4U is alternative
with one open end or with a 16 A 3-pole CEE
standard plug available. Cleaning the filters
system is simple without demounting the
amplifier from the rack. AM-4U is equipped
with two independent brushless andstageless
fans working with automatic speedcontrol
function. The air circulation is front-to-rear,
allowing trouble-free operation even in
smaller power amplifier rack systems.
Also the mechanic construction and
manufacturing guarantee highest precision.
The robust and highly rigid steel chassis is
meant to survive the extensive wear of
touring applications.
AM-4U
Analog control card C-4800 is configured for Amplifier AP-4U or AM-4U.
Ord.No.
101244
101443
101769
101788
101243
101654
101753
101224
101554
101876
101563
101142
101987
101977
101997
101907
Model
T12L/HF
T12 L/A / LF
T15F/A/LF
T15F/A/HF
T12L/B/HF
T12L/B/LF
T15F/B/HF
T15F/B/LF
T18W /LF
TLA -101/HF
TLA -101/LF
Universal 4 in 4 output
Monitor bi amp CM 215 15"2"HF
Monitor bi amp CM 215 15"2"LF
Monitor bi amp CM 212 12"2"HF
Monitor bi amp CM 212 12"2"LF
| 14 |
THE FOLLOWING LIST SHOWS SOME SIGNAL PROCESSING MODULES FOR THE ONAX SERIES PA PRODUCTS.
| 13 |
ANALOG CONTROL CARDC-4800 FOR AP-4U AND AM-4U
Control modules can also be exchanged
conveniently: Switch off the power, take out the
control card, demount the knurled screw from the
control card, take unwanted module out of the
socket in the control card and insert wanted one.
The heart of every modern PA system is the
sophisticated controlling of the loudspeakers.
The analogue control cards are configured for
Amplifier AP-4U or AM-4U.The specified modules
that are configured for a certain system are used
to drive individualized PA systems such as
TLA-101 Line Array system, ONAX PA system
or on-stage monitoring system.
The operation of taking out the control card from
the rack is very simple without disassembling the
amplifier from the rack: Switch off the power,
demount the two knurled screws from the front
panel,disconnect the contact strip out of the input
port in the amplifier and take out the control card.
By properly combining control modules, we can
drive tops (two way active) and woofers together
with one 4-channel amplifier. The various poss-
ibilities of combining control modules according to
real application requirement make configuration
and application of PA systems obviously economic
and efficient.
A wide range of panel modules for different applications
are available. Here we cannot provide a closed listing
of all modules, since the amplifier system, with its open
architecture feature, is still being continuously optimized
and expanded by our talented and innovative R&D
engineers to meet the changing and developing application
demands world wide. So if you are interested in our
updated listing of models, please contact local dealer.
T18W
T12L
T15F
ACCESSORIES
SHACKLES, O-RINGS, CHAINS, STEEL ROPES, SLINGS, CASES AND SPEAKER CABLES
Ord.No. Name
201643 Hoist connecting chain with shackles
201244 Hoist connecting chain with two legs and 2 hooks
201443 Hoist connecting wire rope with 1 hook
201769 Shackles
201788 O-rings
201243 3M Sling
201654 2M Sling
201753 15M Speakon cable
201224 10M Speakon cable
201554 5M Speakon cable
201876 1M Speakon cable
201563 Flight case for 2 ONAX speaker cabinets
201287 Flight Case for 4 TLA-101
201554 Flight Case for 2 TLF-101 Flying frame
201142 PX-7000 Power supply
201987 PX-40 K Power supply
| 16 |
T18W
| 15 |
Ord.No.
101244
101443
101769
101788
101243
101654
101753
101224
101554
101876
101563
101142
101987
101977
101997
101907
Model
T12L/HF
T12 L/A / LF
T15F/A/LF
T15F/A/HF
T12L/B/HF
T12L/B/LF
T15F/B/HF
T15F/B/LF
T18W /LF
TLA -101/HF
TLA -101/LF
Universal 4 in 4 output
Monitor bi amp CM 215 15"2"HF
Monitor bi amp CM 215 15"2"LF
Monitor bi amp CM 212 12"2"HF
Monitor bi amp CM 212 12"2"LF
T15F
T15F
T12L
T12L
Control Modules
PX-40K PX-7000
PX-7000 power supply
Input
Out6
Out5
Out1-4
Max power
Fuse 1-4
Fuse 5
Fuse 6
Case
Weight
1 32A 220-250V,CEE,IP44,3-pole connector
1 32A 220-250V,CEE,IP44,3-pole
1 16A,220-250V,CEE,IP44,3-pole
16A,220-250V,universal Asian standard socket
73KVA
16A/16A 220/230V
16A220/230V
32A 220/230V
1.5mm Metal Case,19"U
6Kg
PX-40K power supply
Case
Output max.
Input max
Output A1-A8 and B1-B8
Output C1 and C2
Output D1-D6
Monitoring
Weight
Dimensions
20 HE 19" back and front door,butterfly locking system, 4 wheels (2 with brake )
43 KVA
3 63 A Cekon socket
8 16A Schuko socket, 8 16A Chinese socket
3 32A 5 pole Cekon socket
32 A 3-pole socket
3 UV Meters, 15 x Control lights
45Kg
1,12M x 0,7M x 0,63M 19" 20U
19" 3U module with 4 32A 3-pin CEE IP 44 socket
19" 3U module with 4 32 A 5-pin CEE IP 44 socket
19" 2U module with 8 15A Schuko CEE IP44 socket
19" 2U module with 8 15A Chinese socket
19" 3U module with 2 32 A 3-pin and 2 32A 5-pin CEE IP44 socket
3U analogue Input UV meter module
3U digital Input UV meter module
3U 3 63 A power input module
Ord.No.66958
Ord.No.66352
Ord.No.66548
Ord.No.66738
Ord.No.66221
Ord.No.66566
Ord.No.66747
Ord.No.66959