PRO
DU
CT C
ATAL
OGU
E | U
K
32
INTRODUCTION 5
CONSTRUCTION 10
MOUNTING PRINCIPLE | GLASSLINE 12
SOLUTIONS 14
DRAIN UNIT | LINE | WALL 16
DRAIN UNIT | CORNER | WALL 18
MOUNTING SET | WALL | FLOOR 19
MOUNTING ELEMENT | WALL 19
OUTLET UNITS | NEW | INTRODUCTION 20
OUTLET UNIT | LINE 22
OUTLET UNIT | CORNER 28
ACCESSORIES | LINE 32
ACCESSORIES | CORNER 33
CLASSICLINE FRAME | WALL 34
CLASSICLINE GRATING 35
CLASSICLINE SOAP SHELF 37
HIGHLINE PANEL | CORNER 38
HIGHLINE FRAME | LINE | WALL 39
HIGHLINE PANEL | LINE 40
HIGHLINE CASSETTE | LINE 41
HIGHLINE CUSTOM | LINE 42
GLASSLINE | FLEXIBLE MODULE 45
GLASSLINE | FIXED MODULE 46
GLASSLINE | SHOWER SCREENS 48
GLASSLINE | SHOWER DOOR 50
GLASSLINE | TOP RAILS 52
MODULE 1100 54
FLEX FRAMES 56
FREESTANDING SYSTEM 58
DRAIN UNIT | LINE | FLOOR 59
CLASSICLINE FRAME | FLOOR 60
HIGHLINE FRAME | FLOOR 61
COLOURS PROVIDE AN OVERVIEW!
In order to provide an overview, unidrain®'s products have been divided into colour categories. These colours are a part of unidrain®'s graphic universe, creating continunity and connection throughout the brochures, price lists, adverts, web, etc.
5
phot
o: Fl
ugha
fen
Stut
tgar
t
VA 2.42/178972
BRILLIANTLY CONCEIVED, FLAWLESS DESIGN
Imagine a bathroom where the floor drain is not in the way during your shower. Where you don't have to stand with one foot positioned on either side of the floor grating, but where the grating is tucked neatly out of the way. Imagine a bathroom featuring built-in elements, not because they have to be there, but
because you prefer to adorn your bathroom with the design.
On the following pages you will see how imagination meets reality. The floor drain which, on the surface, nestles against the wall, beautifully emphasising the bathing area's atmosphere of wellness and comfort,
and which below the surface provides you with the safest and strongest installation on the market. The shower creen, featuring the same safety as the floor drain, is concealed and firmly embedded in the floor
and wall, while also bringing a natural affinity to the bathroom.
unidrain® is world class, award-winning Danish design. Design that not only pleases the eye, but which is just as much a technical product appreciated by installers and architects. The unique, patented flange system works synergistically with the fundamental elements of the construction – the floor and wall – and this principle extends to the installation of the shower screens. The floor drain and shower screens
thus unite in a unique and strong collaboration that has never before been seen.
For the HighLine range:
76
A
B
C
D
A
B
D
D D
Bedr
e Ba
d ©
A
A
BB
C C
EE
FF
unidrain® GlassLine is a range of shower screens designed as a natural extension of the original unidrain® floor drain. Using a unique
flange system, the shower screen is simply and securely installed in the floor and wall and represents a complete concept together with the unidrain® floor drain.
The GlassLine shower screen can be installed in two ways: The fixed module embraces the entire shower cubicle with an integrated drain unit.
The flexible module can be installed on a regular drain unit. Both solutions can be combined with outlet unit, frame, grating/panel and shower screen.
NEWGLASSLINE SHOWER SCREEN
FLEXIBLE MODULEFIXED MODULE
A: Grating or panelB: Frame D: Outlet unitE: Fixed moduleF: Shower screen
A: Grating or panelB: Frame C: Drain unit D: Outlet unitE: Flexible moduleF: Shower screen
Shower screen and floor drain
the unidrain® principle
Combining the products is very simple. With just a few choices, you can select a solution
that suits your bathroom.
FLOOR DRAINS
unidrain®'s floor drains are an intelligent and functional solution. The system is composed of drain unit, outlet unit, frame and
grating/panel, and are available in both line and corner solutions.
The two design ranges, ClassicLine and HighLine, each offer clean lines and streamlined design and constitute the top,
visible part of the floor drain. The installation of the drain unit and the outlet unit is the same for both ranges.
A: Grating or panelB: FrameC: Drain unit D: Outlet unit
A: Grating or panelB: FrameC: Drain unit D: Outlet unit
UNIDRAIN® LINE UNIDRAIN® CORNER
98
In the HighLine range, the traditional grating is replaced by a panel available in three solutions:
- Panel is a brushed stainless steel or frosted glass solution
- Custom is a flat base on top of which you lay your choice of floor tile
- Cassette is a base with wall/floor junctions all the way around, making it suitable for flooring such as terrazzo (using own material)
HIGHLINE
Design for floor drains
The top, visible part of the floor drain is available in two design ranges: ClassicLine and HighLine.
CLASSICLINE
ClassicLine is the original design range from unidrain® and consists of frame and grating. A selection of elegant
and timeless grating designs in brushed stainless steel ensures that there is a product to suit all tastes.
WORTH KNOWING
• The drain unit and outlet unit are the same for both ClassicLine and HighLine
• The frame is mandatory, as the grating is supported by the frame
WORTH KNOWING
• The drain unit and outlet unit are the same for both ClassicLine and HighLine
• The frame is optional and can be omitted, leaving just a narrow slit in the floor to allow water to drain away
HighLineClassicLine ClassicLine
1110
1
2
3
4
5
CONSTRUCTION unidrain® is placed directly against the rear wall. The vertical wall flanges are fixed to the wall and ensure a completely waterproof overlap with the membrane.
Similarly, the horizontal floor flanges ensure the floor is waterproof by overlapping the floor membrane.
unidrain®'s unique construction is patented in Europe (no. 1287213) and awaiting patent
approval in a number of countries worldwide.
unidrain® is a registered trademark.
EN 1253
EN 1253(European Standard
for floor drains)
Floor flange
Reinforcement
Floor membrane
Wall membrane
Reinforcement
Wall flange
Wooden floor joists with 22 mm floor plate (plywood or similar).
Waterproofing system such as lubrication membrane with sealing tape/ reinforcement tape. Tile/tiled brick flooring.
Shown with Mounting Set 22 mm (see page 19).
In-situ concrete on a stable poured foundation with a base made from concrete or other suitable base material. Lubrication membrane with sealing tape/reinforcement tape. Tile/tiled brick flooring.
unidrain® is tested and approved for internal fitting with all types of floor structures
for wet rooms with tiles, heavy concrete structures and lightweight wooden floor joists. For mounting in wooden floor joists and other
lightweight floor constructions, we recommend using the unidrain® Mounting Set
(see page 9).
For all structures, the materials and building methods used must be suited to and approved
for use in a wet room.
Detailed building guidelines can be downloaded from www.unidrain.com
CONCRETE WOODEN FLOOR JOISTS
FOR ALL TYPES OF STRUCTURES
RELIABLE RESULT
Because unidrain® is placed against the wall, it only requires a single-sided slope as opposed to the traditional four-sided incline. It is thus easier to produce a correct base without the risk of depressions or reverse slope.
The result is a completely level floor surface. This makes it easier to lay large tiles that do not require cutting around the drain. The end result is both waterproof and reliable.
BUILDING METHOD
SIMPLE AND PRECISE FITTING AND MOUNTING
Simple and easy mounting with precise fitting ensures correct placement during the entire building process.
FIXATION DURING POURING
The drain unit is fixed throughout the entire pouring process, ensuring it does not move. Placement against the wall, away from the work area, eases the task of reinforcement and floor heating.
EASY PRODUCTION OF A BASE WITH ONE-SIDED SLOPE
A one-sided base makes it easier to produce a correct base without the risk of reverse slope and depressions. The base for the tiled surface is thus completely even and smooth.
WET ROOM SECURE CONNECTION WITH WALL AND FLOOR
The overlap of the membrane with the floor and wall flanges of the drain forms a waterproof and wet room secure seal with the floor and wall.
EASY TILE FITTING ON A TOTALLY FLAT SURFACE
The one-sided slope makes tile laying even easier, even with very large tiles. It is not necessary to cut the tiles to fit around the drain.
1.
2.
3.
4.
5.
1312
WHAT MAKES GLASSLINE UNIQUE- Patented system: A single complete solution for the bathroom- Secure watertight covering of the entire shower cubicle- Quick and easy installation- Defines the slope in the shower cubicle- No visible fittings or screws- Glass surfaces are treated with Cleantec for easier maintenance- Easy to install with underfloor heating
MOUNTING PRINCIPLEUNIDRAIN® GLASSLINE
GlassLine construction is available in two types: the fixed and the flexible module.
The fixed module is a natural extension of the original design of the floor drain.
The fixed module consists of two welded profiles placed perpendicularly on the drain
unit: One is for mounting on the side wall and the other is used for mounting
the shower screen.
The flexible module is a separate profile, which is attached and fastened to the
existing drain units with bolts. The shower screen is then mounted.
CONSTRUCTIONTWO MODELS
FIXED MODULE FLEXIBLE MODULE
WORTH KNOWING
• Can be combined with both ClassicLine and HighLine (with frame)
• Can be installed with HighLine Custom without frame
• Can be combined with drain unit, outlet unit, frame, grating/panel and shower screen from the permanent range
WORTH KNOWING
• Can be combined with both ClassicLine and HighLine (with frame)
• The drain unit is a part of the fixed module
• Can be combined with outlet unit, frame, grating/panel and shower screen from the permanent range
Wall membrane
Reinforcement
Reinforcement
Wall profile
Reinforcement
Reinforcement
Fixed module
Fixed module
Floor membrane
unidrain®'s patented flange system is extended to the installation of the shower screen, making GlassLine the strongest and most wet
room secure installation ever for shower cubicles.
The fixed/flexible module is fitted to the wall and embedded firmly into the floor. When the floor is poured, it follows the two % slope
in the shower cubicle to make the pouring process easier than ever before, and decreases the risk of depressions or reverse slope.
The wall profile is fixed to the rear wall and the shower screen is attached to the profile as well as inserted into the track in the fixed/flexible module. Wall and floor flanges ensure a 100 % waterproof
solution and the tiles elegantly conceal the strong underlying installation. The shower screen is now firmly attached to both the
wall and floor, eliminating the risk of loosening over time.
INSTALLATION PRINCIPLE
WORTH KNOWING• The shower screen can be installed either before or after tile fitting
• The shower screen is mounted on a rail on the wall and can be replaced in case of damage
1514
Install unidrain® in the corner or let it follow the corners.
Place unidrain® along a wall, in a sunken shower cubicle or quite simply wherever there is a need for it.
The illustrations show examples of simple and functional shower cubicles that are possible using unidrain®’s unique floor drain system.
SOLUTIONS
Line solution: 1004 in an open bathroom
Line solution: 1001 in niche with three solid walls.
Line solution: 5002 with right aligned shower screen.
Line solution: 1004 in sunken niche in open bathroom.
Corner solution: 2011 in sunken corner niche.
Module solution: 1100 wall-to-wall in larger bathroom.
Module solution: 1100 in larger niche with three solid walls.
Module solution: 1100 in inward corner.
1716
1003 10041002
(L)(R)
150
57
(C)
80
(H)
(L)(R)
150
(C)
80
(H)
150
80
(R)
(H)
(C)
(L)
57
1001
(L)(R)
150
57
(C)
80
(H)
!57
HighLine
ClassicLine+
Shower cubicle with two solid walls and open/glass partition on the right.
For shower cubicle with three walls.
Total construction height (excl. frame/grating) = height of the outlet unit + (H).
(H) = Distance from the top edge of outlet unit to the top of floor flange/underside of tile.
DRAIN UNIT | LINE | WALL SpecificationsMaterials: 1.5 mm stainless steel (AISI 304)Surface: PickledMembrane: Lubrication membrane or sheet membranes.Floor construction: AllFlooring: Tiles/tile bricks
Shower cubicle with two solid walls and open/glass partition on the left.
For shower cubicle/bath with distance to walls.
Line 1001 Line 1002
For shower cubicle with three solid walls.
The drain unit has three wall flanges and one floor flange.
For shower cubicle with open right side, glass wall or similar.
The drain unit has two wall flanges and two floor flanges.
Usage: Line drain Line drain
Wall flange: Rear wall/left/right Rear wall/left
Length model: 700* 800* 900* 1000* 1200* 700* 800* 900* 1000* 1200*
*Installation length (L): 702 mm 802 mm 902 mm 1,002 mm 1,202 mm 757 mm 857 mm 957 mm 1,057 mm 1,257 mm
Frame (R): 695 mm 795 mm 895 mm 995 mm 1,195 mm 695 mm 795 mm 895 mm 995 mm 1,195 mm
Center (C): 351 mm 401 mm 451 mm 501 mm 601 mm 351 mm 401 mm 451 mm 501 mm 601 mm
Height (H): 17 mm 18 mm 19 mm 20 mm 22 mm 17 mm 18 mm 19 mm 20 mm 22 mm
Item no.: 1001.0700 1001.0800 1001.0900 1001.1000 1001.1200 1002.0700 1002.0800 1002.0900 1002.1000 1002.1200
EAN no.*: 3030 3047 3054 3061 3078 3085 3092 3108 3115 3122
Line 1003 Line 1004
For shower cubicle with open left side, glass wall or similar.
The drain unit has two wall flanges and two floor flanges.
Can be freely positioned against rear wall, independent of any side walls.
The drain unit has one wall flange and three floor flanges.
Line drain Line drain
Rear wall/right Rear wall
700* 800* 900* 1000* 1200* 300* 700* 800* 900* 1000* 1200*
757 mm 857 mm 957 mm 1,057 mm 1,257 mm 432 mm 812 mm 912 mm 1,012 mm 1,112 mm 1,312 mm
695 mm 795 mm 895 mm 995 mm 1,195 mm 315 mm 695 mm 795 mm 895 mm 995 mm 1,195 mm
351 mm 401 mm 451 mm 501 mm 601 mm 216 mm 406 mm 456 mm 506 mm 556 mm 656 mm
17 mm 18 mm 19 mm 20 mm 22 mm 12 mm 17 mm 18 mm 19 mm 20 mm 22 mm
1003.0700 1003.0800 1003.0900 1003.1000 1003.1200 1004.0300 1004.0700 1004.0800 1004.0900 1004.1000 1004.1200
3139 3146 3153 3160 3177 3238 3184 3191 3207 3214 3221
*Please note fitting
dimensions!
*570769200xxxx
1918
!
2011
HighLine
ClassicLine+
(L2)(L2)
(L1)55
63
197
195195
DRAIN UNIT | CORNER | WALL SpecificationsMaterials: 1.5 mm stainless steel (AISI 304)Surface: PickledMembrane: Lubrication membrane or sheet membranes.Floor construction: AllFlooring: Tiles/tile bricks
Shower cubicle with corner drain.
Total construction height (excl. frame/grating) = see page 32-34.
MOUNTING SET | WALL | FLOORMOUNTING ELEMENT | WALL
unidrain® with ClassicLine frame/grating and Mounting Set 22 mm | wall. unidrain® with ClassicLine frame/grating and Mounting Element 135 mm.
Corner 2011
The drain unit has two wall flanges and one floor flange.
Usage: Corner drain
Wall flange Two rear walls
Length model: 200
Length (L): L1: 377/L2: 267 mm
Frame (R): 270/193mm
Item no.: 2011.0200
EAN no.*: 6659
Mounting Set 22 mm Mounting elementLine | wall
300-1000 mm
Line | wall
1,200 mm
Corner | wall
200 mm
Line | floor
300-900 mm
Line | wall
100 mm
Line | wall
135 mm
The set consists of a front, back and side profile(s) that are mounted into wooden joists using screws. The drain unit is inserted into the profile and ”clicked” in place.
Ensures correct placement and fitting of drain unit in wooden floor joist construction. It is customised to various lengths by cutting the front and back profile.
Note: Also available as Mounting Set (38 mm) for wooden floor joist construction with base. See unidrain.dk for more information.
Easier mounting with prefabricated polystyrene sheets.
Can be cut to size and adapted to fit all model lengths.
Usage: Line drain | wall Line drain | wall Corner drain | wall Line drain | floor Line drain Line drain
Fits length model: 300-1000 1200 200 300-900 300-1200 300-1200
Materials: Stainless steel/wood Stainless steel/wood Stainless steel/wood Stainless steel/wood EPS EPS
Surface: Pickled/wood Pickled/wood Pickled/wood Pickled/wood Fibreglass-reinforced mortar surface
Fibreglass-reinforced mortar surface
Fits: 1001.0300-10001002.0300-10001003.0300-10001004.0300-1000
1001.12001002.12001003.12001004.1200
2011.0200 3002.0700-09003004.0300-0900
All line drain units
| wall
All line drain units
| wall
Item no.: 1804.1022 1804.1222 2801.0222 3804.0922 1860.0100 1860.0135
EAN no.*: 3597 3603 4136 6574 6406 6413
*570769200xxxx
*570769200xxxx
2120
Length model
Outlet unit Ø Direction 300 700 800 900 1000 1200
1311.0032 32 mm Horizontal 64 69 70 71 72 74
1311.0050 50 mm Horizontal 64 69 70 71 72 74
1312.0050 50 mm Vertical 108 113 114 115 116 118
1312.0075 75 mm Vertical 113 118 119 120 121 123
1312.0075 + 1850.0075 75 mm Vertical 201 206 207 208 209 211
1411.0050 50 mm Horizontal 98 103 104 105 106 108
1411.0075 75 mm Horizontal 98 103 104 105 106 108
1412.0075 75 mm Vertical 158 163 164 165 166 168
1413.0075 75 mm Horizontal 190 195 196 197 198 200
1414.0075 75 mm Vertical 255 260 261 262 263 265
1415.0050 50 mm Vertical 98 103 104 105 106 108
1417.0050 50 mm Horizontal 64 69 70 71 72 74
LINE: 1001, 1002, 1003 and 1004
CORNER: 2011
Outlet unit Ø Direction mm
2311.0032 32 mm Horizontal 72
2311.0050 50 mm Horizontal 72
2411.0050 50 mm Horizontal 126
2411.0075 75 mm Horizontal 126
2412.0075 75 mm Vertical 193
2415.0032 32 mm Horizontal 72
2415.0050 50 mm Horizontal 72
(see page 22-23).
(see page 24-26).
LOCK FIXTURE FOR DRAIN UNITNew lock fixture for the drain unit ensures that the outlet unit is fixed in exactly the right position
FITTING TO BASEAllows fitting of outlet unit to base
LOCK FIXTURE FOR DRAIN UNITNew lock fixture for the drain unit ensures that the outlet unit is fixed in exactly the right position
LOWER INSTALLATION HEIGHTHeight has been reduced by 10 mm
LOWER INSTALLATION HEIGHTHeight has been reduced by 18 mm
LOWER INSTALLATION HEIGHT• The P-water trap's low installation
height makes it suitable for multi-storey buildings
• High self-cleaning effect
LARGER CAPACITYThe drain outlet capacity is increased by up to 90 %.
WATER TRAP A new ring at the top of the water trap makes it easier to lift it out for cleaning
OUTLET UNITS
NEW GENERATION
INSTALLATION HEIGHT
2322
Ø 32 Ø 50 Ø 50
(H)
48
80
122
150
13
45
77
(H)
38
80
150
132
13
45
77
(H)38
80
150
132
13
45
77
218218 218
5252 52
Ø 75
218
50 101
Ø 50
50
218
50 96
150
80
75
9151
66
13 (H)
150
80
50
75
75
47
58
13 (H)
1312.0075
190
75
180
75
1850.0075
260
(H)
80
150
13
66
140
SpecificationsMaterials: Plastic (PP)
Gasket: EPDM
OUTLET UNIT | LINE
NEW GENERATION NEW GENERATION
• LOWER INSTALLATION HEIGHT• LOCK FIXTURE FOR DRAIN UNIT• FITTING TO BASE
NEW GENERATION
NEW GENERATION NEW GENERATION NEW GENERATION NEW GENERATION
Extra lowinstallation
height:52 mm
Extra lowinstallation
height:52 mm
Extra lowinstallation
height:52 mm
Extra lowinstallation
height:50 mm
Extra lowinstallation
height:50 mm
Extra lowinstallation
height:140 mm
Line 1311.0032 Line 1311.0050 Line 1417.0050
Horizontal outlet unit Ø 32 mm.
Excl. ordour barrier.
Can be turned 180˚ if a backward facing outlet is required.
Horizontal outlet unit Ø 50 mm.
Excl. ordour barrier.
Can be turned 180˚ if a backward facing outlet is required.
Horizontal outlet unit Ø 50 mm.
Includes built-in odour barrier with high self-cleaning effect.
The odour barrier can be removed and cleaned.
Can be turned 180˚ if a backward facing outlet is required. Note: The odour barrier is VA approved.
Usage: Line drain Line drain Line drain
Outlet dimensions: Ø 32 mm Ø 50 mm Ø 50 mm
Outlet direction: Horizontal Horizontal Horizontal
Capacity: 0.4 l/s 0.85 l/s 0.6 l/s
Water trap/odour barrier: Without Without With (odour barrier)
Side inlet: Without Without Without
Fits:1001, 1002, 1003, 1004, 1100, 3002, 3004,
5002, 50031001, 1002, 1003, 1004, 1100, 3002, 3004,
5002, 50031001, 1002, 1003, 1004, 1100, 3002, 3004,
5002, 5003
Item no.: 1311.0032 1311.0050 1417.0050
EAN no.*: 7892 7908 7915
*570769200xxxx
Line 1312.0050 Line 1312.0075 Line 1850.0075
Vertical outlet unit Ø 50 mm.
Excl. ordour barrier.
Vertical outlet unit Ø 75 mm.
Excl. ordour barrier.
P-water trap Ø 75 mm.
High self-cleaning effect.
P-water trap can be used instead of the built-in water trap/odour barrier that comes with some of the outlet units.
Suitable for installation in frequently used showers.
Line drain Line drain Line drain
Ø 50 mm Ø 75 mm Ø 75 mm
Vertical Vertical Horizontal
1.7 l/s 2.5 l/s 1.7 l/s
Without Without
Without Without
1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003
1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003
Outlet unit 1312.0075, 1412.0075, 1414.0075, 2412.0075
1312.0050 1312.0075 1850.0075
7922 7939 7946
!Total construction height (excl.
tiles) = height of the outlet unit + (H).(H) = Distance from top edge of outlet unit to underside of tile.(See measurement specifications for the selected drain unit p. 16-17).The construction height indicated may vary by 3 mm due to manufacturing tolerances.
2524
!
Ø 7586 146
218 218
(H)
(H)
53
86
80
87
139
150
150
13
13
4562
77
99
Ø 75
Ø 50Ø 5086 86
218 218
(H) (H)
58 58
80 80
132 72
150 150
13 13
4545
77 77
NEW GENERATIONNEW GENERATIONNEW GENERATION NEW GENERATION
• LOWER INSTALLATION HEIGHT• LARGER CAPACITY• LOCK FIXTURE FOR DRAIN UNIT
NEW GENERATION
Line 1411.0075 Line 1412.0075
Horizontal outlet unit Ø 75 mm.
Incl. built-in water trap.
The water trap can be removed, separated and cleaned.
Can be turned 180˚ if a backward facing outlet is required.
Vertical outlet unit Ø 75 mm.
Incl. built-in water trap.
The water trap can be removed, separated and cleaned.
Line drain Line drain
Ø 75 mm Ø 75 mm
Horizontal Vertical
1.0 l/s 1.5 l/s
With With
Without Without
Unit 1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003 Unit 1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003
1411.0075 1412.0075
7977 7984
Line 1411.0050 Line 1415.0050
Horizontal outlet unit Ø 50 mm.
Incl. built-in water trap.
The water trap can be removed, separated and cleaned.
Can be turned 180˚ if a backward facing outlet is required.
Horizontal outlet unit Ø 50 mm.
Incl. built-in water trap.
The water trap can be removed, separated and cleaned.
Can be turned 180˚ if a right or left facing outlet is required.
Usage: Line drain Line drain
Outlet dimensions: Ø 50 mm Ø 50 mm
Outlet direction: Horizontal Horizontal
Capacity: 0.91 l/s 0.8 l/s
Water trap: With With
Side inlet: Without Without
Fits: Unit 1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003 Unit 1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003
Item no.: 1411.0050 1415.0050
EAN no.*: 7960 8288
Total construction height (excl. tiles) = height of the outlet unit + (H).(H) = Distance from top edge of outlet unit to underside of tile.(See measurement specifications for the selected drain unit p. 16-17).The construction height indicated may vary by 3 mm due to manufacturing tolerances.
SpecificationsMaterials: Plastic (PP)
Gasket: EPDM
OUTLET UNIT | LINE
*570769200xxxx
2726
!
243178
218218
(H)
150
13
72
Ø 75
Ø 75
Ø 40Ø 40
Ø 40
50
111
85
62
(H)
150
13
72
Ø 40
50
144111
13845
NEW GENERATIONNEW GENERATION
Total construction height (excl. tiles) = height of the outlet unit + (H).(H) = Distance from top edge of outlet unit to underside of tile.(See the measurement specifications for the selected drain unit).The construction height indicated may vary by 3 mm due to manufacturing tolerances.
NEW GENERATION • LOWER INSTALLATION HEIGHT• LARGER CAPACITY• LOCK FIXTURE FOR DRAIN UNIT
Line 1413.0075 Line 1414.0075
Horizontal outlet unit Ø 75 mm.
Incl. built-in water trap (can be separated and cleaned).
Note: The water trap has two function options:- Place the water trap at the top so it is used only for the floor drain.- Push the water trap down into the outlet unit so that it can also be used for the two upper side inlets.
The two lower inlets require a separate water trap.
Can be turned 180˚ if a backward facing outlet is required.
Vertical outlet unit Ø 75 mm.
Incl. built-in water trap (can be separated and cleaned).
Note: The water trap has two function options:- Place the water trap at the top so it is used only for the floor drain.- Push the water trap down into the outlet unit so that it can also be used for the two upper side inlets.
The two lower inlets require a separate water trap.
Usage: Line drain Line drain
Outlet dimensions: Ø 75 mm Ø 75 mm
Outlet direction: Horizontal Vertical
Capacity: 1.5 l/s 1.85 l/s
Water trap: With With
Side inlet: 4 pcs. Ø 40 mm (can be opened if required) 4 pcs. Ø 40 mm (can be opened if required)
Fits: Unit 1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003 Unit 1001, 1002, 1003, 1004, 1100, 3002, 3004, 5002, 5003
Item no.: 1413.0075 1414.0075
EAN no.*: 7991 8004
OUTLET UNIT | LINE
*570769200xxxx
2928 OUTLET UNIT | CORNER SpecificationsMaterials: Plastic (PP)
Gasket: EPDM
Diagonal measurements from inside corner to front. Diagonal measurements from inside corner to front. Diagonal measurements from inside corner to front. Diagonal measurements from inside corner to front.
Corner 2311.0032 Corner 2311.0050
Horizontal outlet Ø 32 mm.
Excl. ordour barrier.
Can be rotated 360˚, which may facilitate direction of pipework.
Horizontal outlet Ø 50 mm.
Excl. ordour barrier.
Can be rotated 360˚, which may facilitate direction of pipework.
Usage: Corner drain Corner drain
Outlet dimensions: Ø 32 mm Ø 50 mm
Outlet direction: Horizontal Horizontal
Capacity: 0.5 l/s 0.8 l/s
Water trap: Without Without
Side inlet: Without Without
Fits: Unit 2011.0200 Unit 2011.0200
Item no.: 2311.0032 2311.0050
EAN no.*: 6581 6598
Corner 2415.0032 Corner 2415.0050
Horizontal outlet Ø 32 mm.
Includes built-in odour barrier with high self-cleaning effect.
The odour barrier can be removed and cleaned.
Can be rotated 360˚, which may facilitate direction of pipework.
Note: The odour barrier is VA approved.
Horizontal outlet Ø 50 mm.
Includes built-in odour barrier with high self-cleaning effect.
The odour barrier can be removed and cleaned.
Can be rotated 360˚, which may facilitate direction of pipework.
Note: The odour barrier is VA approved.
Corner drain Corner drain
Ø 32 mm Ø 50 mm
Horizontal Horizontal
0.4 l/s 0.5 l/s
With (odour barrier) With (odour barrier)
Without Without
Unit 2011.0200 Unit 2011.0200
2415.0032 2415.0050
6789 6796
Extra lowinstallation
height:51 mm
Extra lowinstallation
height:51 mm
Extra lowinstallation
height:51 mm
Extra lowinstallation
height:51 mm
*570769200xxxx
3130 OUTLET UNIT | CORNER
Diagonal measurements from inside corner to front.
Diagonal measurements from inside corner to front.
Diagonal measurements from inside corner to front.
SpecificationsMaterials: Plastic (PP)
Gasket: EPDM
Corner 2411.0050 Corner 2411.0075 Corner 2412.0075
Horizontal outlet Ø 50 mm.
Incl. built-in water trap (can be separated and cleaned).
Can be rotated 360˚, which may facilitate direction of pipework.
Horizontal outlet Ø 75 mm.
Incl. built-in water trap (can be separated and cleaned).
Can be rotated 360˚, which may facilitate direction of pipework.
Vertical outlet Ø 75 mm.
Incl. built-in water trap (can be separated and cleaned).
Usage: Corner drain Corner drain Corner drain
Outlet dimensions: Ø 50 mm Ø 75 mm Ø 75 mm
Outlet direction: Horizontal Horizontal Vertical
Capacity: 0.8 l/s 0.9 l/s 1.0 l/s
Water trap: With With With
Side inlet: Without Without Without
Fits: Unit 2011.0200 Unit 2011.0200 Unit 2011.0200
Item no.: 2411.0050 2411.0075 2412.0075
EAN no.*: 6604 6611 6628
*570769200xxxx
3332 ACCESSORIES | LINE ACCESSORIES | CORNER
NEW GENERATION
Strainer Water trap Water trap Odour barrier Riser piece
1810.0010 1820.0040 1820.0010 1820.0030 35 mm 55 mm
Simplifies daily floor drain maintenance.
Prevents water trap becoming clogged.
Fits outlet units: 1411.0050/1411.0075/ 1412.0075/1413.0075/ 1414.0075/1415.0050
Meets capacity and self-cleaning require-ments according to EN 1253 (the common European standard for floor drains) and is VA approved.
Can easily be removed from the outlet unit using the mounted hook, then separated and cleaned.
Fits outlet units: 1401.0050/1401.0075/ 1402.0075/05.0050/ 1403.0075/1404.0075
Meets capacity and self-cleaning require-ments according to EN 1253 (the common European standard for floor drains) and is VA approved.
Can easily be removed from the outlet unit, disassembled without tools, and cleaned.
Fits outlet units: 1311.0032/1311.0050/ 1312.0050/1312.0075/ 1417.0050
Has automatic odour barrier instead of water trap so it cannot dry out.
The odour barrier can be removed and cleaned.
Note: The odour barrier is VA approved.
Placed between the drain unit and the outlet unit.
Suitable for very deep placement of outlet unit.
Usage: Line drain Line drain Line drain Line drain Line drain Line drain
Model: 1810 1820 1820 1820 H 35 mm H 55 mm
Materials: Stainless steel Plastic (PP) Plastic (PP) Plastic (PP) Plastic (PPS) Plastic (PPS)
Surface: Brushed - - - - -
Gasket: - TPE TPE TPE EPDM EPDM
Item no.: 1810.0010 1820.0040 1820.0010 1820.0030 1830.0035 1830.0055
EAN no.*: 2446 8011 2439 6710 3436 3443
*570769200xxxx
Strainer Water trap Odour barrier Riser piece Hook Shower wiper
2811.0010 2821.0020 2821.0030 2830.0095 1840.0000 5300.0000
Simplifies daily floor drain maintenance.
Prevents water trap becoming clogged.
Fits outlet units: 2411.0050/2411.0075/
2412.0075
Meets capacity and self-cleaning require-ments according to EN 1253 (the common European standard for floor drains) and is VA approved.
Can easily be removed from the outlet unit, disassembled without tools, and cleaned.
Fits outlet units: 2311.0032/2311.0050/
2415.0032/2415.0050
Has automatic odour barrier instead of water trap so it cannot dry out.
The odour barrier can be removed and cleaned.
Placed between the drain unit and the outlet unit.
Suitable for very low placement of outlet unit.
1 pcs. Ø 40 mm side inlet (can be opened if required)
Note: Cannot be combined with water trap 2821.0020.
Hook to lift the water trap out of the outlet unit.
Can be used on line and corner models.
Shower wiper for cleaning the shower cubicle.
Corner drain Corner drain Corner drain Corner drain Corner/Line -
2811 2821 2821 H 95 mm 1840 5300
Stainless steel Plastic (PP) Plastic (PP) Plastic (PP) Plastic/steel Steel/rubber
Brushed - - - - Brushed
- TPE TPE EPDM - -
2811.0010 2821.0020 2821.0030 2830.0095 1840.0000 5300.0000
6666 6673 6680 6697 6802 8219
3534
137
191
Classic
Column
51
(L)
! !
(L2)(L2)
(L1)(H)
18
10
18
(H)*
2
CLASSICLINE FRAME | WALL CLASSICLINE GRATING SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Dimensions: 3 mm solid
SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Insert: Synthetic material
Frame height (H) = tile thickness + approx. 2 mm for tile mortar and membrane. *Frame width = 19 mm incl. 2 mm gap to rear flange = 80 mm incl. 2 mm gap to rear flange
Frame height (H) = tile thickness + approx. 2 mm for tile mortar and membrane.
Cross-section of outlet unit with frame and grating. *Height of frame.
Line 1500 Corner 2500
The height of the frame (8, 10 or 12 mm) depends on the thickness of the floor tile. The rubber insert ensures accurate fitting inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.
The frame is mandatory and has a double function – to support the grating and provide a perfectly flush finish with the tile/tile brick.
Usage: Line drain Corner drain
Length model: 300* 700* 800* 900* 1000* 1200* 200*
Length (L): 315 mm 695 mm 795 mm 895 mm 995 mm 1,195 mm L1: 270/L2: 193 mm
Fits: Unit 1004 Unit 1001, 1002, 1003, 1004, 1100, 5002, 5003 Unit 2011
Item no.: 8 mm (H)
1500.0308 1500.0708 1500.0808 1500.0908 1500.1008 1500.1208 2501.0208
EAN no.: 3245 3276 3306 3337 3368 3399 2606
Item no.: 10 mm(H)
1500.0310 1500.0710 1500.0810 1500.0910 1500.1010 1500.1210 2501.0210
EAN no.: 3252 3283 3313 3344 3375 3405 2613
Item no.: 12 mm(H)
1500.0312 1500.0712 1500.0812 1500.0912 1500.1012 1500.1212 2501.0212
EAN no.*: 3269 3290 3320 3351 3382 3412 2620
Line 1600 Corner 2600
The grating is placed on a countersunk bearing inside the frame to ensure a precise fit.
Can only be used with ClassicLine frame.
Usage: Line drain Corner drain
Length model: 300* 700* 800* 900* 1000* 1200* 200*
Length (L): 280 mm 660 mm 760 mm 860 mm 960 mm 1,160 mm 191 mm
Item no.:Classic
1601.0300 1601.0700 1601.0800 1601.0900 1601.1000 1601.1200 2601.0200
EAN no.*: 2231 1098 1104 1111 2255 2279 15.5036.020
Item no.:Column
1602.0300 1602.0700 1602.0800 1602.0900 1602.1000 1602.1200 2602.0200
EAN no.*: 2286 1128 1135 1142 2309 2323 2668
Item no.:Inca
1603.0300 1603.0700 1603.0800 1603.0900 1603.1000 1603.1200 -
EAN no.*: 2330 1159 1166 1173 2354 2378 -
Item no.:Square
1604.0300 1604.0700 1604.0800 1604.0900 1604.1000 1604.1200 -
EAN no.*: 2385 1180 1197 1203 2408 2422 -
Item no.:Stripe
1605.0300 1605.0700 1605.0800 1605.0900 1605.1000 1605.1200 -
EAN no.*: 2897 2910 2927 2934 2941 2965 -
Item no.: Anni-versario
1606.0300 1606.0700 1606.0800 1606.0900 1606.1000 1606.1200 -
EAN no.*: 8226 8233 8240 8257 8264 8271 -
*Please note installation dimensions!
*570769200xxxx
Classic Column Inca Square Stripe Anniversario19
19
10 (H)
80
(L)
3736
204
288
315
86
Classic
Column
Classic
Column
CLASSICLINE SOAP SHELF SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Line 1850 Corner 2850
Soap shelf incl. grating and installation set.
Designed for insertion in tile joint or screw mounting into existing shower cubicle.
For corner installation only.
Usage: Wall Wall
Length model: 300* 200*
Length (L)*: 315 mm 288/204 mm
Item no.:Classic
1850.0301 2850.0201
EAN no.*: 6369 6383
Item no.:Column
1850.0302 2850.0202
EAN no.*: 6376 6390
*Please note installation dimensions!
*570769200xxxx
3938
!
198142 198142
6
270201
6 66 6
HIGHLINE FRAME | LINE | WALL SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Insert: Synthetic material
Frame height (H) = tile thickness + approx. 2 mm for tile mortar and membrane. Without use of frame: air gap between panel and floor tile = 6 mm.*Frame width = 19 mm incl. 2 mm gap to rear flange = 76 mm incl. 2 mm gap to rear flange
SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Heightener set: Plastic (POM)
Without frame With frame
Cross-section of drain unit without frame/ with Panel in brushed stainless steel.
Cross-section of drain unit with frame/ with Panel in brushed stainless steel.
Heightener setH: 6, 8, 11, 21 mm.Mounted under the panel.
HIGHLINE PANEL | CORNER
Line 1910
The frame is optional but is designed to emphasise the exclusive design of the floor drain.
The height of the frame (10, 12 or 25 mm) depends on the thickness of the floor tile.
Exclusive frame design with 4 mm solid stainless steel surface.
Insert ensures accurate fitting inside the unit.
Usage: Line drain
Length model: 300* 700* 800* 900* 1000* 1200*
Length (L)*: 315 mm 695 mm 795 mm 895 mm 995 mm 1,195 mm
Fits unit: 1004 1001, 1002, 1003, 1004, 1100, 5002, 5003
Item no.: 10 mm (H)
1910.0310 1910.0710 1910.0810 1910.0910 1910.1010 1910.1210
EAN no.*: 4242 4259 4266 4273 4280 4297
Item no.: 12 mm(H)
1910.0312 1910.0712 1910.0812 1910.0912 1910.1012 1910.1212
EAN no.*: 4303 4310 4327 4334 4341 4358
Item no.: 15 mm(H)
1910.0315 1910.0715 1910.0815 1910.0915 1910.1015 1910.1215
EAN no.*: 4365 4372 4389 4396 4402 4419
Item no.: 25 mm(H)
1910.0325 1910.0725 1910.0825 1910.0925 1910.1025 1910.1225
EAN no.: 4426 4433 4440 4457 4464 4471
HighLine corner
The frame is optional but is designed to emphasise the exclusive design of the floor drain.
The height of the frame (10, 12 or 25 mm) depends on the thickness of the floor tile.
Exclusive frame design with 4 mm solid stainless steel surface.
Usage: Corner drain
Length model: Panel excl. frame Panel incl. frame
Length model: 200* 200* 200* 200* 200*
Height: – 10 mm 12 mm 15 mm 25 mm
Item no.: Brushed stainless
steel
2920.0201 2911.0210 2911.0212 2911.0215 2911.0225
EAN no.*: 6772 7038 7045 7052 7069
*Please note installation dimensions!
*570769200xxxx
*570769200xxxx
25
19*
8 (H)
76*
(L)
4140
1 2 5 15
(L)
37
1 2 5 15
(L)
(H)
37
SpecificationsMaterials: Stainless steel (AISI 304)/safety glass
Surface: Brushed/frosted
Heightener set: Plastic (PE)
SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Heightener set: Plastic (PE)
Heightener setH: 1, 2, 5, 15 mm.Adjust height for Panel when floor tile is over 10 mm thick.Installed between panel and rail.
Heightener setH: 1, 2, 5, 15 mm.Adjust height for Cassette when floor tile is over 10 mm thick.Installed between cassette and rail.
Cross-section of drain unit with frame and Panel in brushed stainless steel.
Cross-section of drain unit with frame and Cassette.
Cross-section of drain unit without frame and with Cassette.
Without use of frame: air gap between Cassette and floor tile = 6 mm.
HIGHLINE PANEL | LINE HIGHLINE CASSETTE | LINE
Without frame With frame Without frame With frame
Line 1920 | PANEL
Choose between solid brushed stainless steel or frosted glass.
The set consists of a panel, rail, heightener set and screws. The set must be assembled before mounting.
The Panel solution is placed directly inside the unit, where the shape of the rail ensures a precise fit.
Can be installed with or without HighLine frame (see frame p. 43).
Set includes 6 mm tile template, which is used as a distance piece when mounting without a frame.
Usage: Line drain
Length model: 300* 700* 800* 900* 1000* 1200*
Length with/without frame (L)*: 253/315 mm 633/695 mm 733/795 mm 833/895 mm 933/995 mm 1133/1,195 mm
Item no.: Brushed stainless steel
1920.0300 1920.0700 1920.0800 1920.0900 1920.1000 1920.1200
EAN no.*: 4488 4495 4501 4518 4525 4532
Item no.: frosted glass White
1930.0300 1930.0700 1930.0800 1930.0900 1930.1000 1930.1200
EAN no.*: 6819 6826 6833 6840 6857 6864
Item no.: frosted glass Black
1931.0300 1931.0700 1931.0800 1931.0900 1931.1000 1931.1200
EAN no.*: 6871 6888 6895 6901 6918 6925
Line 1940 | CASSETTE
The set consists of a cassette, rail, heightener set and screws. The set must be assembled before mounting.
Available in 10, 12, 15 and 25 mm heights, (depending on the thickness of the floor tile).
Can be supplemented with own material such as matching floor tile, terrazzo etc.onto which it is mounted.
The Cassette solution is placed directly inside the unit, where the shape of the rail ensures a precise fit.
Can be installed with or without HighLine frame (see frame p. 43).
Set includes 6 mm tile template, which is used as a distance piece when mounting without a frame.
Usage: Line drain
Length model: 300* 700* 800* 900* 1000* 1200*
Length with/without frame L)*:
253/315 mm 633/695 mm 733/795 mm 833/895 mm 933/955 mm 1133/1,195 mm
Item no.: 10 mm(H)
1940.0310 1940.0710 1940.0810 1940.0910 1940.1010 1940.1210
EAN no.*: 5089 5096 5102 5119 5126 5133
Item no.: 12 mm(H)
1940.0312 1940.0712 1940.0812 1940.0912 1940.1012 1940.1212
EAN no.*: 5140 5157 5164 5171 5188 5195
Item no.: 15 mm(H)
1940.0315 1940.0715 1940.0815 1940.0915 1940.1015 1940.1215
EAN no.*: 5201 5218 5225 5232 5249 5256
Item no.: 25 mm(H)
1940.0325 1940.0725 1940.0825 1940.0925 1940.1025 1940.1225
EAN no.*: 5263 5270 5287 5294 5300 5317
*Please note installation dimensions!
*570769200xxxx
*570769200xxxx
Cross-section of drain unit without frame and Panel in stainless steel. Without use of frame: air gap between Panel and floor tile = 6 mm.
4342
2
146103
6 43
6 10 3
6
14
6
6 mm
6 mm
6 mm
1
3
2
6
4
14
1 2 5 15
(L)
37
SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Heightener set: Plastic (PE)
HIGHLINE CUSTOM | LINE
Heightener setH: 1, 2, 5, 15 mm.Adjust height of Custom base if the tiles on the base do not have the same thickness as the tiles on the rest of the floor.Installed between base and rail.
Cross-section of drain unit with frame and Custom (with own materials).
Cross-section of drain unit without frame and Custom (with own materials). Without use of frame: gap between Custom and floor tile = 6 mm.
The Custom solution consists of a rail and a stainless steel base. The shape of the rail ensures accurate fitting inside the unit. The rail and the base are screwed together after which your choice of tile can then be laid. A heightener set is included for height adjustment of the base.
INSTALLATIONHIGHLINE CUSTOMEXAMPLE WITH 10 MM TILE
Floor tile is cut to achieve a gap between the tile on the base and the other tiles of at least 6 mm.
Custom rail and base seen from below.
BASE SIDES Lay own tiles on base with overhang of max. 20 mm (depending on tile thickness and type of tile. In this example the overhang is 14 mm).
BASE, LONG SIDE Lay own tiles on base with overhang of max. 10 mm (depending on tile thickness and type of tile. In this example the overhang is 6 mm).
1.
2.
3.
4.
Recommended glue
Tile(10 mm)
Glue (1 mm)
Custom Panel (5 mm)
LENGTH SECTION
Riserpiece
Custom baseOverhang
Riserpiece
Overhang
Tile(10 mm)
Tile
Tile mortar(3 mm)
Tile mortar
Glue
CROSS-SECTION
The products are shown in random order.
Manufacturer Product
Bostik • Maxibond
• Maxibond X-TREME
• Clearbond
Danalim • Montage Ekstra 292
• Turbo tack 291
Henkel • Pattex no more nails
Novatech • Tec7
• Trans7
Without frame With frame
Rail
Line 1950 | CUSTOM
The set consists of a Custom base, rail, heightener set and screws. The set must be assembled before mounting.
Glue own material such as matching floor tile on the base to complete the solution.
The Custom solution is placed directly inside the unit, where the shape of the rail ensures a precise fit.
Can be installed with or without HighLine frame (see frame p. 43).
Set includes 6 mm tile template, which is used as a distance piece when mounting without a frame.
Usage: Line drain
Length model: 300* 700* 800* 900* 1000* 1200*
Length with/without frame (L)*: 253/315 mm 633/695 mm 733/795 mm 833/895 mm 933/995 mm 1133/1,195 mm
Item no.: 1950.0300 1950.0700 1950.0800 1950.0900 1950.1000 1950.1200
EAN no.*: 5324 5331 5348 5355 5362 5379
*Please note installation dimensions!
*570769200xxxx
4544
HighLine
ClassicLine+
66
60-165
(D)
900: H = 17 mm 1000: H = 19 mm 1200: H = 24 mm
308143
6658
4,5
68
54
10
2104
GLAS
SLIN
ESpecificationsMaterials: 1.5 mm stainless steel (AISI 304)Surface: PickledMembrane: Lubrication membrane or sheet membranesFloor construction: Concrete/woodFlooring: Tiles/tile bricks
GLASSLINE | FLEXIBLE MODULE
Flexible module 5000
Can be combined with units 1002/1003/1004 in all lengths.
The flexible module has a built-in slope so the floor in the shower cubicle slants the correct two % downward to the floor drain.
The shower niche is framed by flanges on two sides and increases wet room safety.
The shower screen is installed in the track of the fixed module to eliminate risk of loosening over time.
Combine with: outlet unit, drain unit, frame, grating/panel and shower screen.
Model: 900* 1000* 1200*
Shower screen depth: 900 mm 1,000 mm 1,200 mm
*Installation depth (D) 998 mm 1,098 mm 1,302 mm
Slope: 17 19 24
Item no.: 5000.0900 5000.1000 5000.1200
EAN no.*: 7380 7397 7403
*Please note installation dimensions!
*570769200xxxx
Drain unit, outlet unit, frame and grating/panel are not included!
shower screen
(900, 1000, 1200)
glass
packing 1 mm
(Slope)
4746
!
HighLine
ClassicLine+
(A)
(R)
(B)
(D)
66 (H)(C)
19
60 - 165
801, 901, 100166
40
143
19
3658
66
(A)
(R)
(B)(H)
60 - 165
Shower screen, outlet unit, frame and grating/panel are not included! 4,5
6810
2085
(glass)
(slope)
packing 1 mm
2104
54
Total construction height (excl. frame/grating) = height of the outlet unit + (H).
(H) = Distance from the top edge of outlet unit to the top of floor flange/underside of tile.
GLASSLINE | FIXED MODUL SpecificationsMaterials: 1.5 mm stainless steel (AISI 304)Surface: PickledMembrane: Lubrication membrane or sheet membranes.Floor construction: Concrete/woodFlooring: Tiles/tile bricks
*Please note installation dimensions!
Fixed module 5002 | Right aligned shower screen
The fixed module has a built-in slope so the floor in the shower cubicle slants the correct two % downward to the floor drain.
The shower niche is framed by flanges on three sides and increases wet room safety.
The shower screen is installed in the track of the fixed module to eliminate risk of loosening over time.
Combine with: outlet unit, frame, grating/panel and shower screen.
Fixed module Length model (A): 800* 900* 1000*
*Installation dimensions (A): 864 mm 964 mm 1,064 mm
*Installation dimensions (D): 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm
Shower screen (B): 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm
Frame (R): 795 mm 895 mm 995 mm
Slope: 19 mm 19 mm 19 mm
Center (C): 451 mm 501 mm 601 mm 451 mm 501 mm 601 mm 451 mm 501 mm 601 mm
Height (H): 18 mm 19 mm 20 mm
Item no.: 5002.0809 5002.0810 5002.0812 5002.0909 5002.0910 5002.0912 5002.1009 5002.1010 5002.1012
EAN no.*: 7205 7212 7229 7236 7243 7250 7267 7274 7281
Fixed module 5003 | Left aligned shower screen
The fixed module has a built-in slope so the floor in the shower cubicle slants the correct two % downward to the floor drain.
The shower niche is framed by flanges on three sides and increases wet room safety.
The shower screen is installed in the track of the fixed module to eliminate risk of loosening over time.
Combine with: outlet unit, frame, grating/panel and shower screen.
800* 900* 1000*
864 mm 964 mm 1,064 mm
1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm
900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm
795 mm 895 mm 995 mm
19 mm 19 mm 19 mm
451 mm 501 mm 601 mm 451 mm 501 mm 601 mm 451 mm 501 mm 601 mm
18 mm 19 mm 20 mm
5003.0809 5003.0810 5003.0812 5003.0909 5003.0910 5003.0912 5003.1009 5003.1010 5003.1012
7298 7304 7311 7328 7335 7342 7359 7366 7373
*570769200xxxx
Shower screen, outlet unit, frame and grating/panel
are not included!
(Slope)
4948
Stripe RandomColumn ColumnRandom Stripe Transparent
58
(D: 900, 1000, 1200)
26
2104
58(D: 900, 1000, 1200)
2104
26
4,5
68
54
SpecificationsMaterials: stainless steel (AISI 304),10 mm safety float glassDecoration: screen print
GLASSLINE | SHOWER SCREENS
Design: Stripe Design: Column Design: Random
GlassLine | Right aligned shower screens
10 mm safety glass.
The glass surface is treated with Cleantec nano technology, making it water-repellent, less susceptible to limescale and easier to clean.
Applied screen print decoration on the outer surface.
No visible screws or fittings in the finished result.
Design: Design: Stripe Design: Column Design: Random
Model: 900* 1000* 1200* 900* 1000* 1200* 900* 1000* 1200*
Depth (D): 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm
*Installation dimensions: 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm
Height: 2,104 mm 2,104 mm 2,104 mm
Weight incl. packaging: 55 kg 65 kg 79,5 kg 55 kg 65 kg 79,5 kg 55 kg 65 kg 79,5 kg
Item no.: 5110.0902 5110.1002 5110.1202 5120.0902 5120.1002 5120.1202 5130.0902 5130.1002 5130.1202
EAN no.*: 7441 7458 7465 7502 7519 7526 7564 7571 7588
Design: Stripe Design: Column Design: Random Design: Transparent
GlassLine | Left aligned shower screens GlassLine | Shower screen
10 mm safety glass.
The glass surface is treated with Cleantec nano technology, making it water-repellent, less susceptible to limescale and easier to clean.
Applied screen print decoration on the outer surface.
No visible screws or fittings in the finished result.
10 mm safety glass.
Both sides have been given a hydrophobic surface treatment with nano technology (Cleantec) so the shower screen can be placed to the right or the left..
No visible screws or fittings in the finished result.
Design: Stripe Design: Column Design: Random Design: Transparent
900* 1000* 1200* 900* 1000* 1200* 900* 1000* 1200* 900* 1000* 1200*
900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm 900 mm 1,000 mm 1,200 mm
1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm 1,002 mm 1,102 mm 1,302 mm
2,104 mm 2,104 mm 2,104 mm 2,104 mm
55 kg 65 kg 79,5 kg 55 kg 65 kg 79,5 kg 55 kg 65 kg 79,5 kg 55 kg 65 kg 79,5 kg
5110.0903 5110.1003 5110.1203 5120.0903 5120.1003 5120.1203 5130.0903 5130.1003 5130.1203 5100.0900 5100.1000 5100.1200
7472 7489 7496 7533 7540 7557 7595 7601 7618 7410 7427 7434
*Please note installation dimensions!
*570769200xxxx
(see page 49, 50)
5150
2023
GlassLine top rail
GlassLine shower door
GlassLine top rail
The shower door is flush with the steel profile of the Glassline shower screen
776/ 876/ 976
180
10
5
180
*570769200xxxx
Shower door
THE SHOWER DOOR IS ADAPTED TO THE HEIGHT AND WIDTH OF UNIDRAIN’S GLASSLINE SHOWER WALL.
MUST BE COMBINED WITH UNIDRAIN® TOP RAIL.
Tile thickness incl. tile adhesive: 8-12 mm
The surface is treated with Cleantec nanotechnonology on both sides
Supplied with two hinges and a sealing strip
Model: 800* 900* 1000*
*Depth 776 mm 876 mm 976 mm
Height: 2023 mm
Item no.: 5400.0800 5400.0900 5400.1000
EAN no.*: 8479 8486 8462
SpecificationsMaterials: stainless steel8 mm safety float glass
5352
1200
700 / 800 / 900 / 1000 / 1200
40
200
100100
100
40
40
15
15
15
GLASSLINE SHOWER SCREENS SpecificationsMaterials: stainless steel (AISI 304)
SpecificationsMaterials: stainless steel (AISI 304),10 mm safety float glass
Top rail 5310
For finishing the shower screen.
A top rail is recommended for stabilising shower screens measuring 1,200 mm or more.
The top rail is available in one length and can be adjusted to fit the individual shower cubicle.
(See full image p. 48)
Usage: For shower screen For shower screen
Fits: Right aligned shower screens Left aligned shower screens
Materials: Brushed stainless steel Brushed stainless steel
Fits length model: 700-1200 700-1200
Width: 40 mm 40 mm
Height:: 15 mm 15 mm
Item no.: 5310.1202 5310.1203
EAN no.*: 8158 8295
*570769200xxxx
Top rail 5320
For finishing the shower screen.
A top rail is recommended for stabilising shower screens measuring 1,200 mm or more.
For shower screen For shower screen
Right aligned shower screens Left aligned shower screens
Brushed stainless steel, glass Brushed stainless steel, glass
700 800 900 1000 1200 700 800 900 1000 1200
40 mm 40 mm 40 mm 40 mm 40 mm 40 mm 40 mm 40 mm 40 mm 40 mm
15 mm 15 mm 15 mm 15 mm 15 mm 15 mm 15 mm 15 mm 15 mm 15 mm
5320.0702 5320.0802 5320.0902 5320.1002 5320.1202 5320.0703 5320.0803 5320.0903 5320.1003 5320.1203
8165 8172 8189 8196 8202 8301 8318 8325 8332 8349
5554
HighLine
ClassicLine+
MODULE 1100
FLEXIBILITY FORLARGE BATHROOMS
Module 1100 is a customised modular line drain system that is manu-factured to order. Modular line drains can be many meters long and are therefore ideal for institutions, changing rooms and large bathrooms.
Outlet units, frames and gratings are taken from the permanent range. This means that frames and gratings are placed end-to-end, making maintenance easy and manageable. A number of outlet units are also used to ensure as high capacity and low construction height as possible.
Module 1100 for mid-floor placement is available upon request. www.unidrain.com/module1100
You can calculate your own modular line drain system and find the measurement that best fits your individual bathroom.
• Enter your bathroom measurements and choose your combination of modules
• Choose a ClassicLine or HighLine solution
• Choose an outlet unit
Immediately view a design showing the specifications of your individual line drain. Send your calculations to us and we will prepare an estimate for you.
Examples of solutions
Inward corner Outward corner
One module with flex frames Maintain the vertical end flanges, even those with odd dimensions. Extra space can be filled out with flex frames at the sides.
Two modules with angle and flex frameAllow the modular line drain to follow the corners in the shower area so that showers can be installed in several walls.
Two modules without flex framesA modular line drain system that covers double the length of a standard model when not extended with flex frames.
Two modules with flex framesIf the modular line drain has odd measurements, the extra space can be filled out with symmetrically placed flex frames.
Welded together into one component
prior to delivery!
A: Grating or panelB: FrameC: Flex frameC: Drain unit D: Outlet unit A
AAB
D
E
CB
D
C
E
B
D
E
C
WORTH KNOWING
• Modular line drain components are welded together and delivered as one long drain unit
• One frame and one grating/panel are used for each module which are placed end-to-end in in the modular line drain system
• One outlet unit is used for each module to maintain a high capacity and low installation height
5756 SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Flex frames are installed along with
floor tiles!
A: Flex frame end piece/middle piece
B: Flex frame inward corner
C: Flex frame outward corner
FLEX FRAMES
ClassicLine High Line
Flex frames
Flex frames are used to extend the visible lenghth of the floor drain. The are laid end-to-end and installed using tile mortar, so there is no need to cut small pieces of tile.
Flex frames can be used for:
- Drain systems from the permanent range, allowing the module unit to be customised by down to a 10 mm jump.- Module 1100 line drains that cover the distance between frames and gratings to provide a visually uninterrupted result.
Usage: Line drain Line drain
Model: ClassicLine HighLine
Height: H 8 mm H 10 mm H 12 mm H 10/12/15/25 mm
Length: Item no.: EAN no.*: Item no.: EAN no.*: Item no.: EAN no.:* Item no.: EAN no.*:
A:
10 mm 1510.0108 3771 1510.0110 3788 1510.0112 3795 1911.0110 6420
20 mm 1510.0208 3801 1510.0210 3818 1510.0212 3825 1911.0210 6437
30 mm 1510.0308 3832 1510.0310 3849 1510.0312 3856 1911.0310 6444
40 mm 1510.0408 3863 1510.0410 3870 1510.0412 3887 1911.0410 6451
50 mm 1510.0508 3894 1510.0510 3900 1510.0512 3917 1911.0510 6468
60 mm 1510.0608 3924 1510.0610 3931 1510.0612 3948 1911.0610 6475
70 mm 1510.0708 3955 1510.0710 3962 1510.0712 3979 1911.0710 6482
80 mm 1510.0808 3986 1510.0810 3993 1510.0812 4006 1911.0810 6499
90 mm 1510.0908 4013 1510.0910 4020 1510.0912 4037 1911.0910 6505
100 mm 1510.1008 4044 1510.1010 4051 1510.1012 4068 1911.1010 6512
110 mm 1510.1108 4075 1510.1110 4082 1510.1112 4099 1911.1110 6529
120 mm 1510.1208 4105 1510.1210 4112 1510.1212 4129 1911.1210 6536
B corner 1530.1208 6963 1530.1210 6970 1530.1212 6987 1913.1210 6550
C corner 1520.0808 6932 1520.0810 6949 1520.0812 6956 1912.0810 6543
*570769200xxxx
5958
30043002 3002
!
HighLine
ClassicLine+
(L)(R)
208
(C)
71
(H)
H: 120 - 2404 stk.H: 120 - 2404 stk.
(L)(R)
208
(C)
71
(H)
57
SpecificationsMaterials: 1.5 mm stainless steel (AISI 304)Surface: PickledMembrane: Lubrication membrane or sheet membranes.Floor construction: AllFlooring: Tiles/tile bricks
Introduction Sides without wall flanges must comply with rules regarding min. distance to wall.
For line units placed against rear wall, we refer to series 1000 (see pages 16-17).
Freely mounted into floor with a wall on the left.
Freely mounted into floor with a wall on the right.
Freely mounted into floor without walls.
Total construction height (excl. frame/grating) = height of the outlet unit + (H).(H) = Distance from the top edge of outlet unit to the top of floor flange/underside of tile.
FREESTANDING SYSTEMDRAIN UNIT | LINE | FLOOR
Line 3002 Line 3004
For shower cubicle with one solid wall.
The drain unit has one wall flange and three floor flanges.
Incl. Four height-adjustable feet (120-220 mm).
Note: see frames on pp. 58-59
For shower cubicles without fixed side walls.
The drain unit has four floor flanges.
Incl. Four height-adjustable feet (120-220 mm).
Note: see frames on pp. 58-59
Usage: Line drain Line drain
Wall flange: Left or right (can be turned 180˚ if necessary) None
Length model: 700* 900* 300* 700* 800* 900* 1000* 1200*
Length (L): 757 mm 957 mm 432 mm 812 mm 912 mm 1,012 mm 1112 mm 1312 mm
Center (C): 351 mm 451 mm 206 mm 396 mm 456 mm 496 mm 556 mm 656 mm
Height (H): 17 mm 19 mm 12 mm 17 mm 18 mm 19 mm 20 mm 22 mm
Frame (R): 695 mm 895 mm 315 mm 695 mm 795 mm 895 mm 995 mm 1195mm
Item no.: 3002.0700 3002.0900 3004.0300 3004.0700 3004.0800 3004..0900 3004.1000 3004.1200
EAN no.*: 6109 6116 6123 6130 7076 6147 7083 7090
Phot
o: Go
dtve
d Sc
hool
, Cop
enha
gen
*Note installation dimensions!
*570769200xxxx
6160
! !
8837 8868
8844 8875
8851 8882
SpecificationsMaterials: Stainless steel (AISI 304)
Surface: Brushed
Insert: Synthetic material
CLASSICLINE FRAME | FLOOR HIGHLINE FRAME | FLOOR
Frame height (H) = tile thickness + approx. 2 mm for tile mortar and membrane. Frame height (H) = tile thickness + approx. 2
mm for tile mortar and membrane. Without use of frame: air gap between panel and floor tile = 6 mm.
Line 3910 | HighLine
The frame is optional but is designed to emphasise the exclusive design of the floor drain.
The height of the frame (10, 12 or 25 mm) depends on the thickness of the floor tile.
Exclusive frame design with 4 mm solid stainless steel surface. Insert ensures accurate fitting inside the unit.
HighLine Panel, Cassette or Custom must be selected (see pages 40-42).
Usage: Line drain
Length model: 300* 700* 800* 900* 1000* 1200*
Length (L): 315 mm 695 mm 795 mm 895 mm 995 mm 1195 mm
Fits: Unit 3004 Unit 3002, 3004 Unit 3004 Unit 3002, 3004 Unit 3004
Item no.: 10 mm(H)
3910.0310 3910.0710 3910.0810 3910.0910 3910.1010 3910.1210
EAN no.*: 6246 6284 8899 6321 8936 8974
Item no.: 12 mm(H)
3910.0312 3910.0712 3910.0812 3910.0912 3910.1012 3910.1212
EAN no.*: 6253 6291 8905 6338 8943 8981
Item no.: 15 mm(H)
3910.0315 3910.0715 3910.0815 3910.0915 3910.1015 3910.1215
EAN no.*: 6260 6307 8912 6345 8950 8998
Item no.: 25 mm(H)
3910.0325 3910.0725 3910.0825 3910.0925 3910.1025 3910.1225
EAN no.*: 6277 6314 8929 6352 8967 9001
Line 3500 | ClassicLine
The height of the frame (8, 10 or 12 mm) depends on the thickness of the floor tile.
The rubber insert ensures accurate fitting inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. (see gratings p. 35).
The frame is mandatory and has a double function – to support the grating and provide a perfectly flush finish with the tile/tile brick.
Usage: Line drain
Length model: 300* 700* 800* 900* 1000* 1200*
Length (L): 315 mm 695 mm 795 mm 895 mm 995 mm 1195 mm
Fits: Unit 3004 Unit 3002, 3004 Unit 3004 Unit 3002, 3004 Unit 3004
Item no.: 8 mm(H)
3500.0308 3500.0708 3500.0808 3500.0908 3500.1008 3500.1208
EAN no.*: 6154 6185 8806 6215
Item no.: 10 mm(H)
3500.0310 3500.0710 3500.0810 3500.0910 3500.1010 3500.1210
EAN no.*: 6161 6192 8813 6222
Item no.: 12 mm(H)
3500.0312 3500.0712 3500.0812 3500.0912 3500.1012 3500.1212
EAN no.*: 6178 6208 8820 6239
*Please note installation dimensions!
*570769200xxxx
*570769200xxxx
17 25
10 8
10 8(H) (H)
71 65
(L) (L)
6362
Unidrain A/SFarum Gydevej 71DK-3520 Farum
T +45 3910 1010F +45 3910 [email protected]
Editi
on 2
. Uni
drai
n as
sum
es n
o re
spon
sibili
ty fo
r prin
ting
erro
rs.
700
UK
©U
nidr
ain
A/S
| A
ll R
ight
s Res
erve
d