smartARS provertical fuse switch disconnectors
- thermoplastics of V0 flammability class- double clearance between open contacts- arc chutes with deionization plates over every contact- fast installation using PPN technology- remote monitoring- built-in current transformers- adapted to existing assembly systems- reversibility - top/bottom cable terminal connection- wide range of accesories
SWITCHGEAR
smart thinking
SWITCHGEAR
6
CONSTRUCTION
smartARS pro fuse switch disconnectors are manufactured in two versions: one pole switching (separately each pole) three pole switching (three poles at the same time)
They have manually operated handle therefore making and breaking operations should be done withdetermined movement.smartARS pro fuse switch disconnectors are available in following sizes (according to rated current): 00 (160 A); 2 (400 A); 3(630 A).smartARS pro fuse switch disconnectors are designed for installation on to 185 mm busbar system.
All plastic parts of fuse switch disconnector smartARS pro are made of halogen free, fibre glass strengthened, self extinguishing materials. Thanks to the application of flame retardants the highest flammability class – V0 was achie-ved. Fuse switch disconnectors made from such termoplastics self-extinguish in specified time after ignition sour-ce is removed. Also dripping of flaming parts of plastic does not occur.Silver plated contacts provide low power loss. Depending on clamp type, smartARS pro fuse switch disconnec-tors enable user to connect circular or sector-shaped conductors with bare ends or conductors with lug terminals. Arc chutes equipped with steel deionization plates are installed over each contact. smartARS pro fuse switch di-sconnectors are designed for using current transformers and ammeters. Protection degree of IP30 from the front is provided. In opened position smartArs pro provide protection degree IP20. Additionally offered accesories enable to install smartARS fuse switch disconnectors of different sizes on common busbar systems and facilitate opera-tion. All sizes of ARS pro fuse switch disconnectors are provided complete with clamps (i. e. screws, V-terminals, 2V-terminals) and shrouds for cable terminals.
GENERAL NFORMATION
smartARS pro vertical fuse switch disconnectors are designed for distribution of electricity and protection against short circuits and overloads in three phase alternative current circuits. They are intended for direct installation on horizontal or vertical busbar systems.smartARS pro fuse switch disconnectors meet technical requirements of polish and european electricity boards and are conformed with EN 60947-1, EN 60947-3, IEC 60947-1, IEC 60947-3 standards. smartARS pro fuse switch di-sconnectors are dedicated for applications which require reliability and safety like low voltage distribution boards in-stalled in transformer substations, industrial low voltage assemblies and cable cabinets.
Design of smartARS pro fuse switch disconnectors provides clearly visible, safe gap in the current circuit after the fuse link removal.
smartARS pro fuse switch disconnectors are designed to perform the following functions: protection energy distribution earthing switching touch protection
GE
NE
RA
L N
FOR
MA
TIO
N
ENERGY SAFELY SWITCHED
7
OPERATING CONDITIONS to be installed in the room free of any dust, aggressive or explosive gases, altitude up to 2000 meters above sea level, outdoor – in cabinets with protection degree > IP 34, ambient temperature from -25 °C to +55 °C, relative humidity of the air should not be higher than 50% at temperature of +40°.
Parameters smartARS 00 pro smartARS 2 pro smartARS 3 pro
Rated thermal current Ith=Inwith fuse links A 160 400 630
Rated voltage Un V 690 690 690
Utilization category
690 VAC-22B AC-22B
AC-21B
500 V AC-22B
400 V AC-23B AC-23B AC-23B
Rated switching current Ie A 160 400 630
Rated short-circuit making current
690 V
kA
80 100 80
500 V100 120 120
400 V
Rated short-circuit withstand current
690 V
kA
80 100 80
500 V100 120 120
400 V
Rated insulation voltage Ui V 1000 1000 1000
Rated impulse withstand voltage Uimp. kV 12 12 12
Rated frequency Hz 50-60 50-60 50-60
Mechanical durability Numberof cycles
1600 1000 1000
Electrical durability 200 200 200
IP degree of protection IP 30 30 30
Fuse links size - 00 1, 2 3
Table 1. MAIN TECHNICAL DATA OF smartARS pro
FUNCTIONALITY making and breaking operations should be done with determined movement, parallelly moving, double contact system, designed for installation on 185 mm busbar system two versions: single pole switching (separately each pole) or triple pole switching (three poles at the same time), fuse switch disconnectors width: 50 mm(smartARS00 pro), 100 mm (smartARS 2,3 pro) suitable for top cable terminal connection, possible connection of conductors with lug terminals (screw terminals) or circular/sector-shaped conductors
with bare ends (V-terminals, 2V-terminals) using V-clamps voltage test is performed through test holes possible installation of earthing device fast installation using PPN technology remote monitoring built-in current transformers adapted to existing assembly systems
TEC
HN
ICA
L DA
TA
SWITCHGEAR
8
smar
tAR
S 00
pro Parameters smartARS 00 pro
Rated thermal current Ith=In A 160
Rated thermal current Ith=Inwith solid links A 210
Rated voltage Un V 690
Utilization category -AC-22B AC-23B
690 400
Rated switching voltage Ue V 690
Rated switching current Ie A 160
Rated short circuit making current
690 VkA
80
500 V 100
Rated short circuit withstand current
690 VkA
80
500 V 100
Rated insulation voltage Ui V 1000
Rated impulse withstand voltage Uimp. kV 12
Rated frequency Hz 50-60
Mechanical durability Number of cycles
1600
Electrical durability 200
IP degree of protection IP 30
Fuse links size - 00
Accesories on page 58
Version Weight Article No.
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 00-1-V pro cable terminals: V-terminals: V-clamps 25-150SW 2,5 kg 63-001414-001
smartARS 00-1 pro cable terminals: bridge terminals (S) 4-70mm2, M8 screw terminals 2,4 kg 63-001414-002
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 00-3-V pro cable terminals: V-terminals: V-clamps 25-150SW 2,6 kg 63-001415-001
smartARS 00-3 pro cable terminals: bridge terminals (S) 4-70mm2, M8 screw terminals 2,5 kg 63-001415-002
smartARS 00 pro version with adjusted to front line and terminal cover of ARS 2,3 without using adapters
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 00-1-V pro cable terminals: V-terminals: V-clamps 25-150SW 2,6 kg 63-002070-001
smartARS 00-1 pro cable terminals: bridge terminals (S) 4-70mm2, M8 screw terminals 2,5 kg 63-002070-002
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 00-3-V pro cable terminals: V-terminals: V-clamps 25-150SW 2,7 kg 63-002071-001
smartARS 00-3 pro cable terminals: bridge terminals (S) 4-70mm2, M8 screw terminals 2,6 kg 63-002071-002
smartARS 00 pro version with fast installation modules using PPN technology
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 00-1-V SM pro cable terminals: V-terminals: V-clamps 25-150SW 2,7 kg 63-001899-001
smartARS 00-1 SM pro cable terminals: bridge terminals (S) 4-70mm2, M8 screw terminals 2,6 kg 63-001899-002
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 00-3-V SM pro cable terminals: V-terminals: V-clamps 25-150SW 2,9 kg 63-001904-001
smartARS 00-3 SM pro cable terminals: bridge terminals (S) 4-70mm2, M8 screw terminals 2,8 kg 63-001904-002
FUSE SWITCH DISCONNECTOR smartARS 00 pro (160 A, 690 V)For installation on to 185 mm busbar systemFuse switch disconnector’s width 50 mm Switching: three poles simultaneously - operation with two hands or single pole switching
smartARS 00-1 pro smartARS 00-3 pro
Table 2. TECHNICAL DATA
Table 3. VERSIONS
ENERGY SAFELY SWITCHED
9
smartA
RS 00 pro
Table 4. smartARS 00 pro TERMINAL CLAMPS
Description smartARS 00 pro
ClampS-bridge clamp
2 x M5 x 25M8 screw* V- clamp 25-150 SW HM 10-120
Picture of clamp
Drawing of clamp
Cross –section of conductors
4 - 70 mm2Lug terminalmax 185 mm2
re 16 mm2 - 95 mm2
se 25 mm2 - 150 mm2re 10 mm2 - 70 mm2
se 25 mm2 - 120 mm2
rm 16 mm2 - 95 mm2
sm 25 mm2 - 150 mm2rm 10 mm2 - 70 mm2
sm 25 mm2 - 95 mm2
Tightening torque 3 Nm** 12 Nm** 20 Nm** 15 Nm**
***
For stranded conductors using cable ferrules is recommended
**) using tension wrench is recommended***) fuse switch disconnectors with V-terminals are equipped with steel V-clamp HM 10-120 on request
fuse switch disconnector to busbar system – 12 Nm, recommended tightening torque for screws and nuts with property class 8.8 – 21 Nm
SWITCHGEAR
10
Possibility of connection of fused tee off adapter for temporary power supply
Padlocking and sealing in closed and parked position
Test holes
Rotary cover with labeling area
FUSE SWITCH DISCONNECTOR smartARS 2 pro (400 A, 690 V) smartARS 3 pro (630 A, 690 V)
smar
tAR
S 2
pro|
sm
art A
RS
3 pr
o
For installation on to 185 mm busbar systemFuse switch disconnector’s width 100 mm 3- pole switching - 3 phases simultaneously or 1-pole switching - each phase separately
smartARS 2 pro
Fuse monitoring module
Possibility of sealing each phase separately
ENERGY SAFELY SWITCHED
11smartARS 2 pro (400 A, 690 V)
Parameters smartARS 2 pro
Rated thermal current Ith with fuse links A 250(NH1), 400(NH2)Rated thermal current Ith with solid links A 600Rated voltage Un V 690Utilization category - AC-22B AC-23BRated switching voltage Ue V 690 400Rated switching current Ie A 250(NH1), 400(NH2)
Rated short circuit making currentUe=690 V kA
100Ue=500 V 120
Rated short circuit withstand currentUe=690 V kA
100Ue=500 V 120
Rated insulation voltage Ui V 1000Rated impulse withstand voltage Uimp. kV 12Rated frequency Hz 50-60Mechanical durability Number
of cycles1000
Electrical durability 200IP degree of protection IP 30Fuse links size - 1, 2Accesories on page 59
Version Weight Article No.
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independentlysmartARS 2-1-V pro cable terminals: V-terminals: V-clamps 240 mm2 5,8 kg 63-001340-001
smartARS 2-1-M pro cable terminals: screw terminals: pressed nuts M12 5,7 kg 63-001340-003
smartARS 2-1-2V pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,4 kg 63-001340-005
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneouslysmartARS 2-6-V pro cable terminals: V-terminals : V-clamps 240 mm2 5,8 kg 63-001341-001
smartARS 2-6-M pro cable terminals: screw terminals: pressed nuts M12 5,7 kg 63-001341-003
smartARS 2-6-2V pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,4 kg 63-001341-005
smartA
RS 2 pro
Fuse switch disconnector designed for operation with NH1 and NH2 fuse links
smartARS 2 pro version equipped with modules for fast installation using PPN technology
for installation on 185 mm busbar system, fast installation modules equipped with screws, ONE POLE SWITCHING - each phase independently
smartARS 2-1-V SM pro cable terminals: V-terminals: V-clamps 240 mm2 6,2 kg 63-001340-201
smartARS 2-1-M SM pro cable terminals: screw terminals: pressed nuts M12 6,1 kg 63-001340-203
smartARS 2-1-2V SM pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,8 kg 63-001340-205
for installation on 185 mm busbar system, fast installation modules equipped with screws, THREE POLE SWITCHING - all phases simultaneously
smartARS 2-6-V SM pro cable terminals: V-terminals: V-clamps 240 mm2 6,2 kg 63-001341-201
smartARS 2-6-M SM pro cable terminals: screw terminals: pressed nuts M12 6,1 kg 63-001341-203
smartARS 2-6-2V SM pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,8 kg 63-001341-205
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, ONE POLE SWITCHING - each phase independently
smartARS 2-1-V SMH pro cable terminals: V-terminals: V-clamps 240 mm2 6,4 kg 63-001340-401
smartARS 2-1-M SMH pro cable terminals: screw terminals: pressed nuts M12 6,3 kg 63-001340-403
smartARS 2-1-2V SMH pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,0 kg 63-001340-405
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, THREE POLE SWITCHING - all phases simultaneously
smartARS 2-6-V SMH pro cable terminals: V-terminals: V-clamps 240 mm2 6,4 kg 63-001341-401
smartARS 2-6-M SMH pro cable terminals: screw terminals: pressed nuts M12 6,3 kg 63-001341-403
smartARS 2-6-2V SMH pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,0 kg 63-001341-405
smartARS 2-1-M prosmartARS 2-6-M pro
Table 5. TECHNICAL DATA
Table 6. VERSIONS
SWITCHGEAR
12
smar
tAR
S 2
pro
Description smartARS 2-x-V pro smartARS 2-x-2V pro
Clamp V- clamp 35-300SW-B V- clamp HS 2/35-240-C
Picture of clamp
Cro
ss-s
ectio
n of
co
nduc
tors
Cro
ss-s
ectio
n of
co
nduc
tors
35 - 185 mm2 35 - 240 mm2 35 - 185 mm2 35 - 240 mm2
35 - 240 mm2 35 - 300 mm2 35 - 240 mm2 35 - 300 mm2
Tightening torque 30 Nm 40 Nm
For stranded conductors using cable ferrules is recommended*) Bars of maximum width of 40 mm and maximum thickness of 8 mm can be fixed to M type screw terminals when protective barrier between phases is installed.
fuse switch disconnector to busbar system – 32 Nm, recommended tightening torque for screws and nuts with property class 8.8 – 56 Nm
Description smartARS 2-x-2V pro smartARS 2-x-M pro
Clamp V- clamp 2/35-300SW-B M–screw M12*
Picture of clamp
Cro
ss-s
ectio
n of
co
nduc
tors
Cro
ss-s
ectio
n of
co
nduc
tors
Lug
term
inal
bare end with crosssection of
35 - 185 mm2 35 - 240 mm2
35 - 240 mm2 35 - 300 mm2
Tightening torque 30 Nm 56 Nm
Tabela 7. smartARS 2 pro TERMINAL CLAMPS
ENERGY SAFELY SWITCHED
13smartARS 3 pro (630 A, 690 V)
Parameters smartARS 3 pro
Rated thermal current Ith with fuse links A 630
Rated thermal current Ithwith solid links A 750Rated voltage Un V 690Utilization category - AC-23B AC-22B AC-21BRated switching voltage Ue V 400 500 690Rated switching current Ie A 630
Rated short circuit making current690 V
kA80
500 V 120Rated short circuit withstand current kA 100Rated insulation voltage Ui V 1000Rated impulse withstand voltage Uimp. kV 12Rated frequency Hz 50-60Mechanical durability Number
of cycles1000
Electrical durability 200IP degree of protection IP 30Fuse links size - 3Accesories on page 59
Version Weight Article No.
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independentlysmartARS 3-1-V pro cable terminals: V-terminals: V-clamps 240 mm2 6,6 kg 63-001340-002
smartARS 3-1-M pro cable terminals: screw terminals: pressed nuts M12 6,5 kg 63-001340-004
smartARS 3-1-2V pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,2 kg 63-001340-006
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneouslysmartARS 3-6-V pro cable terminals: V-terminals: V-clamps 240 mm2 6,6 kg 63-001341-002
smartARS 3-6-M pro cable terminals: screw terminals: pressed nuts M12 6,5 kg 63-001341-004
smartARS 3-6-2V pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,2 kg 63-001341-006
smartARS 2 pro version equipped with modules for fast installation using PPN technology
for installation on 185 mm busbar system, fast installation modules equipped with screws, ONE POLE SWITCHING - each phase independently
smartARS 3-1-V SM pro cable terminals: V-terminals: V-clamps 240 mm2 7,0 kg 63-001340-202
smartARS 3-1-M SM pro cable terminals: screw terminals: pressed nuts M12 6,9 kg 63-001340-204
smartARS 3-1-2V SM pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,6 kg 63-001340-206
for installation on 185 mm busbar system, fast installation modules equipped with screws, THREE POLE SWITCHING - all phases simultaneously
smartARS 3-6-V SM pro cable terminals: V-terminals: V-clamps 240 mm2 7,0 kg 63-001341-202
smartARS 3-6-M SM pro cable terminals: screw terminals: pressed nuts M12 6,9 kg 63-001341-204
smartARS 3-6-2V SM pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,6 kg 63-001341-206
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, ONE POLE SWITCHING - each phase independently
smartARS 3-1-V SMH pro cable terminals: V-terminals: V-clamps 240 mm2 7,2 kg 63-001340-402
smartARS 3-1-M SMH pro cable terminals: screw terminals: pressed nuts M12 7,1 kg 63-001340-404
smartARS 3-1-2V SMH pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,8 kg 63-001340-406
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, THREE POLE SWITCHING - all phases simultaneously
smartARS 3-6-V SMH pro cable terminals: V-terminals: V-clamps 240 mm2 7,2 kg 63-001341-402
smartARS 3-6-M SMH pro cable terminals: screw terminals: pressed nuts M12 7,1 kg 63-001341-404
smartARS 3-6-2V SMH pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,8 kg 63-001341-406
smartA
RS 3 pro
smartARS 3-1-M pro smartARS 3-6-M pro
Table 8. TECHNICAL DATA
Table 9. VERSIONS
SWITCHGEAR
14
smar
tAR
S 3
pro
Tabela 10. smartARS 3 pro TERMINAL CLAMPS
Description smartARS 3-x-V pro smartARS 3-x-2V pro
Clamp V- clamp 35-300SW-B V- clamp HS 2/35-240-C
Picture of clamp
Cro
ss-s
ec-
tion
of
cond
ucto
rs
Cro
ss-s
ec-
tion
of
cond
ucto
rs
35 - 185 mm2 35 - 240 mm2 35 - 185 mm2 35 - 240 mm2
35 - 240 mm2 35 - 300 mm2 35 - 240 mm2 35 - 300 mm2
Tightening torque 30 Nm 40 Nm
Description smartARS 3-x-2V pro smartARS 3-x-M pro
Clamp V- clamp 2/35-300SW-B M–screw M12*
Picture of clamp
Cro
ss-s
ectio
n of
co
nduc
tors
Cro
ss-s
ectio
n of
co
nduc
tors
Lug
term
inal
bare end with crosssection of
35 - 185 mm2 35 - 240 mm2
35 - 240 mm2 35 - 300 mm2
Tightening torque 30 Nm 56 Nm
For stranded conductors using cable ferrules is recommended*) Bars of maximum width of 40 mm and maximum thickness of 8 mm can be fixed to M type screw terminals when protective barrier between phases is installed.Apator takes responsibility for technical quality of V-terminals manufactured only by the company. Minimum tightening torque (M12 screw) for screws
ENERGY SAFELY SWITCHED
15
smartA
RS pro
with lateral busbar term
inals
Description smartARS 2-x-NL pro smartARS 2-x-NR pro smartARS 3-x-NL pro smartARS 3-x-NR pro
Clamp M12 screw M12 screw M12 screw M12 screw
Picture of clamp
Lateral busbar terminals Left side Right side Left side Right side
Tightening torque 56 Nm 56 Nm 56 Nm 56 Nm
FUSE SWITCH DISCONNECTOR smartARS proWITH LATERAL BUSBAR TERMINALS
Version Weight Article No.
Fuse switch disconnectors smartARS 2 pro - 400A
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 2-1 NL pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - left side 5,1 kg 63-002045-001
smartARS 2-1 NR pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - right side 5,1 kg 63-002045-003
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 2-6 NL pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - left side 5,1 kg 63-002046-001
smartARS 2-6 NR pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - right side 5,1 kg 63-002046-003
smartARS 3 pro - 630 A
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 3-1 NL pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - left side 5,9 kg 63-002045-002
smartARS 3-1 NR pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - right side 5,9 kg 63-002045-004
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 3-6 NL pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - left side 5,9 kg 63-002046-002
smartARS 3-6 NR pro cable terminals: screw terminals : pressed nuts M12; lateral busbar terminals - right side 5,9 kg 63-002046-004
Table 11. TECHNICAL DATA
Table 12. VERSIONS WITH LATERAL BUSBAR TERMINALS
(separation, coupling of busbar systems)
Parameters smartARS 2 pro smartARS 3 proRated thermal current Ith with fuse links A 400 630Rated voltage Un V 690 690
Utilization category690 V
- AC-22BAC-21B
500 V AC-22B400 V AC-23B -
Rated switching current Ie A 400 630
Rated short circuit making current600 V
kA100 80
500 V 120 120400 V
Rated short circuit withstand current600 V
kA100 80
500 V 120 120400 VRated insulation voltage Ui V 1000 1000Rated impulse withstand voltage Uimp. kV 12 12Rated frequency Hz 50-60 50-60Mechanical durability Number
of cycles1000 1000
Electrical durability 200 200IP degree of protection IP 30 30Fuse links size - 1,2 3Accesories on page 59
smartARS 2-1-NR pro
Table 13. smartARS 2 pro I smartARS 3 pro WITH LATERAL BUSBAR TERMINALS - TERMINAL TYPES
SWITCHGEAR
16
elec
tron
ic fu
se m
onito
ring
mod
ule
FUSE MONITORING MODULE
The fuse switch disconnector can be equipped with device that al-lows indication of the current state of the fuse links. Information about fuse link burnout, correct operation or power failure are indi-cated by diode light signal or can be transferred to any automation protection system, through the relay contacts.
NOMINAL PARAMETERS
Voltage value for cable test 2,5 kV DC Minimum operating voltage 200 V Maximum operating voltage 690 V Uimp impulse withstand voltage with operated fuse link 4 kV Uimp between phases 4 kV Uimp between main circuit / relay contacts 3,5 kV Temperature range -40...+85°C Rated insulation voltage Ui 1000 V
MODULE OUTPUTS:
Rated current 100 mA Maximum switching voltage 50 V DC
Fuse links state (resultant)
NO output
NC output diode colour
correct operation „0” (0V) „1” (24V) green
failure „1” (24V) „0” (0V) red
The transport outputs can be supplied with a DC voltage of up to 50 V with current limitation to max. 100mA
Minus should be connected directly to the common terminal, outputs should be connected through the load to the plus.
NC-C
COM-E
NO-C
NNC ”+”COM ”-”NO ”+”
DESCRIPTION OF OPERATION OF THE FUSE MONITORING MODULE
diode is green - correct operation, fuse link works correctly diode is red - failure, fuse link operated diode is red; blinking - phase shift (another phase voltage was detected
at the fuse link outgoing contact) diodes off - module switched off / no power supply
ENERGY SAFELY SWITCHED
17
electronic fuse monitoring m
odule
Table 14. VERSIONS WITH ELECTRONIC FUSE MONITORING MODULE
Fuse switch disconnectors smartARS 2 pro - 400A
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 2-1-V-X pro cable terminals: V-terminals: V-clamps 240 mm2 5,9 kg 63-001340-601
smartARS 2-1-M-X pro cable terminals: screw terminals: pressed nuts M12 5,8 kg 63-001340-603
smartARS 2-1-2V-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,5 kg 63-001340-605
smatARS 2-1-V-X-E pro 6,0 kg 63-811830-201
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 2-6-V-X pro cable terminals: V-terminals: V-clamps 240 mm2 5,9 kg 63-001341-601
smartARS 2-6-M-X pro cable terminals: screw terminals: pressed nuts M12 5,8 kg 63-001341-603
smartARS 2-6-2V-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,5 kg 63-001341-605
smartARS 2 pro version equipped with modules for fast installation using PPN technology
for installation on 185 mm busbar system, fast installation modules equipped with screws, ONE POLE SWITCHING - each phase independently
smartARS 2-1-V SM-X pro cable terminals: V-terminals: V-clamps 240 mm2 6,3 kg 63-001340-701
smartARS 2-1-M SM-X pro cable terminals: screw terminals: pressed nuts M12 6,2 kg 63-001340-703
smartARS 2-1-2V SM-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,9 kg 63-001340-705
for installation on 185 mm busbar system, fast installation modules equipped with screws, THREE POLE SWITCHING - all phases simultaneously
smartARS 2-6-V SM-X pro cable terminals: V-terminals: V-clamps 240 mm2 6,5 kg 63-001341-701
smartARS 2-6-M SM-X pro cable terminals: screw terminals: pressed nuts M12 6,4 kg 63-001341-703
smartARS 2-6-2V SM-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,9 kg 63-001341-705
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, ONE POLE SWITCHING - each phase independently
smartARS 2-1-V SMH-X pro cable terminals: V-terminals: V-clamps 240 mm2 6,5 kg 63-001340-801
smartARS 2-1-M SMH-X pro cable terminals: screw terminals: pressed nuts M12 6,4 kg 3-001340-803
smartARS 2-1-2V SMH-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,9 kg 63-001340-805
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, THREE POLE SWITCHING - all phases simultaneously
smartARS 2-6-V SMH-X pro cable terminals: V-terminals: V-clamps 240 mm2 6,5 kg 63-001341-801
smartARS 2-6-M SMH-X pro cable terminals: screw terminals: pressed nuts M12 6,4 kg 63-001341-803
smartARS 2-6-2V SMH-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 6,9 kg 63-001341-805
Version Weight Article No.
Fuse switch disconnectors smartARS 00 pro - 160A
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smatARS 00-1-V-X-E pro cable terminals: V-terminals: V-clamps 25-150SW + hooked clamps 3,1 kg 63-001606-201
SWITCHGEAR
18
smartARS 3 pro version equipped with modules for fast installation using PPN technology
for installation on 185 mm busbar system, fast installation modules equipped with screws, ONE POLE SWITCHING - each phase independently
smartARS 3-1-V SM-X pro cable terminals: V-terminals: V-clamps 240 mm2 7,1 kg 63-001340-702
smartARS 3-1-M SM-X pro cable terminals: screw terminals: pressed nuts M12 7,0 kg 63-001340-704
smartARS 3-1-2V SM-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,7 kg 63-001340-706
for installation on 185 mm busbar system, fast installation modules equipped with screws, THREE POLE SWITCHING - all phases simultaneously
smartARS 3-6-V SM-X pro cable terminals: V-terminals: V-clamps 240 mm2 7,1 kg 63-001341-702
smartARS 3-6-M SM-X pro cable terminals: screw terminals: pressed nuts M12 7,0 kg 63-001341-704
smartARS 3-6-2V SM-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,7 kg 63-001341-706
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, ONE POLE SWITCHING - each phase independently
smartARS 3-1-V SMH-X pro cable terminals: V-terminals: V-clamps 240 mm2 7,3 kg 63-001340-802
smartARS 3-1-M SMH-X pro cable terminals: screw terminals: pressed nuts M12 7,2 kg 63-001340-804
smartARS 3-1-2V SMH-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,9 kg 63-001340-806
for installation on 185 mm busbar system, fast installation modules equipped with hooked clamps, THREE POLE SWITCHING - all phases simultaneously
smartARS 3-6-V SMH-X pro cable terminals: V-terminals: V-clamps 240 mm2 7,3 kg 63-001341-802
smartARS 3-6-M SMH-X pro cable terminals: screw terminals: pressed nuts M12 7,2 kg 63-001341-804
smartARS 3-6-2V SMH-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,9 kg 63-001341-806
Fuse switch disconnectors smartARS 3 pro - 630A
for installation on 185 mm busbar system, ONE POLE SWITCHING - each phase independently
smartARS 3-1-V-X pro cable terminals: V-terminals: V-clamps 240 mm2 6,7 kg 63-001340-602
smartARS 3-1-M-X pro cable terminals: screw terminals: pressed nuts M12 6,6 kg 63-001340-604
smartARS 3-1-2V-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,3 kg 63-001340-606
for installation on 185 mm busbar system, THREE POLE SWITCHING - all phases simultaneously
smartARS 3-6-V-X pro cable terminals: V-terminals: V-clamps 240 mm2 6,7 kg 63-001341-602
smartARS 3-6-M-X pro cable terminals: screw terminals: pressed nuts M12 6,6 kg 63-001341-604
smartARS 3-6-2V-X pro cable terminals: 2V-terminals: double V-clamps 240 mm2 7,3 kg 63-001341-606
elec
tron
ic fu
se m
onito
ring
mod
ule
ENERGY SAFELY SWITCHED
19
NO
TES
NOTES