Instruction Manual
200 SeriesCentrifugal Pumps
Read and understand this manual prior to operating or servicing this product.
611 Sugar Creek Road
Delavan, WI 53115
Tel: (800) 252-5200 or (262) 728-1900Fax: (800) 252-5012 or (262) 728-4904
E-mail: [email protected] site: www.gowcb.com
Information contained in this manual is subject to change without notice and does not represent a commitment on the part of SPX Corporation. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express writ-ten permission of SPX Corporation.
Copyright 2001, 2010 SPX Corporation. All Rights Reserved.
Gore-Tex is a registered trademark of W.L. Gore & Associates, Inc. Kalrez is a registered trademark of DuPont Dow Elastomers. Chemraz is a registered trademark of Greene, Tweed & Co.
Revision Date: 10/2010
Publication: 95-03009
Waukesha Cherry-Burrell Table of Contents
Warranty ................................................................................................................5
Shipping Damage or Loss ...................................................................................... 5Warranty Claim ...................................................................................................... 5
Safety .....................................................................................................................6Care of Stainless Steel .........................................................................................7
Stainless Steel Corrosion ....................................................................................... 7Elastomer Seal Replacement Following Passivation ............................................. 7
Introduction ...........................................................................................................8Manual Content ...................................................................................................... 8Receiving Your Pump ............................................................................................ 8
Receiving and Inspection .......................................................................... 8Pump Characteristics ............................................................................................. 9200 Series Base Mount Description ....................................................................... 9
Base Mount Components .......................................................................... 9Motor Adapter ........................................................................................... 9Stand ......................................................................................................... 10Base (Optional) ......................................................................................... 10
Performance Characteristics .................................................................................. 13Authorization ............................................................................................. 13Standard Construction .............................................................................. 13Construction Options ................................................................................. 13
Operating Parameters ............................................................................................ 14Capacities .............................................................................................................. 15Dimensions ............................................................................................................ 16Centrifugal 200 Series Pump and Pedestal Weights ............................................. 22
Installation .............................................................................................................24Pump Location ....................................................................................................... 24Pump Leveling ....................................................................................................... 24Supply and Discharge Piping/Valves ..................................................................... 24
Installations That May Cause Operation Problems ................................... 26Electrical Connections ............................................................................................ 26Flush Seal Option ................................................................................................... 27
Type 4 Seal (Double mechanical with flush) ............................................. 27Before First Startup ................................................................................................ 28
Clean Pump and Piping ............................................................................ 28Cleaning Safety Procedures .................................................................................. 28
Manual Cleaning ....................................................................................... 28Cleaning-In-Place (CIP) ............................................................................ 28
Preliminary Test Run .............................................................................................. 29Check For Possible Motor Overload Conditions ....................................... 29
Operation ...............................................................................................................30Starting the Pump .................................................................................................. 30Priming the Pump/Stopping the Pump ................................................................... 30
Priming the Pump With the Feed Source Above Pump Level ................... 30Priming the Pump With the Feed Source Below Pump Level ................... 31Stopping the Pump .................................................................................... 31
Maintenance ..........................................................................................................32Scheduled Maintenance ......................................................................................... 32
Routine Maintenance ................................................................................ 32Disassembly of Pump With a Type 1 Seal ............................................................. 32
Removal of the Water Cascade ................................................................ 32Inspect Parts ............................................................................................. 34
Assembly of Pump With a Type 1 Seal .................................................................. 34Backplate Assembly .................................................................................. 34Backplate/Impeller Assembly .................................................................... 3510/2010 95-03009 Page 3
Table of Contents Waukesha Cherry-Burrell
Type 4 Double Seal ................................................................................................ 37
Disassembly of Type 4 Seal ...................................................................... 37Removal of the Water Cascade ................................................................. 38Assembly of Type 4 Seal ........................................................................... 39
Disassembly of Modular Base-Mounted Pumps ..................................................... 41Disassembling the Outer Seal Assemblies ................................................ 42Assembling the Outer Seal Assemblies ..................................................... 42
Pre-assembled (Cartridge) Seals ......................................................................... 43Disassembly of Pre-assembled (Cartridge) Seals ..................................... 43Assembly of a Pump With Pre-assembled (Cartridge) Seals .................... 44
Pedestal Base-Mounted Pump Housing Lubrication .............................................. 46Pump Alignment ..................................................................................................... 46
Checking Angular Alignment ..................................................................... 46Checking Parallel Alignment ...................................................................... 46
Servicing the Electric Motor .................................................................................... 47General Service Information ...................................................................... 47Motor Lubrication Instructions ................................................................... 47
Standard Seal Dimensions .....................................................................................48Cartridge Seal Dimensions .....................................................................................49
Parts Lists ..............................................................................................................50Type 1 Seal Kits ..................................................................................................... 50Type 4 Seal Kits ..................................................................................................... 51Type 1 Seal Components and Common Parts ....................................................... 52Type 4 Seal Components and Common Parts ....................................................... 542045 Pump Parts .................................................................................................... 562065LV - 2065 - 2065HV Pump Parts .................................................................... 582075 Pump Parts .................................................................................................... 602085LV - 2085 Pump Parts .................................................................................... 622105 Pump Parts .................................................................................................... 64Style C Small Bore Pedestal Mount Parts ............................................................ 66Style C Large Bore Pedestal Mount Parts ........................................................... 68Motor Mounts .......................................................................................................... 70Motor Shaft Shims .................................................................................................. 70
Troubleshooting ....................................................................................................71Page 4 95-03009 10/2010
Waukesha Cherry-Burrell Warranty
10/2010 95-03009 Page 5
Warranty
Seller warrants its products to be free from defect in materials and work-manship for a period of one (1) year from the date of shipment. This war-ranty shall not apply to products which require repair or replacement due to normal wear and tear or to products which are subjected to accident, misuse or improper maintenance. This warranty extends only to the origi-nal Buyer. Products manufactured by others but furnished by Seller are exempted from this warranty and are limited to the original manufacturers warranty.
Sellers sole obligation under this warranty shall be to repair or replace any products that Seller determines, in its discretion, to be defective. Seller reserves the right either to inspect the products in the field or to request their prepaid return to Seller. Seller shall not be responsible for any transportation charges, duty, taxes, freight, labor or other costs. The cost of removing and/or installing products which have been repaired or replaced shall be at Buyers expense.
Seller expressly disclaims all other warranties, express or implied, includ-ing without limitation any warranty of merchantability of fitness for a par-ticular purpose. The foregoing sets forth Sellers entire and exclusive liability, and Buyers exclusive and sole remedy, for any claim of damages in connection with the sale of products. In no event shall Seller be liable for any special consequential incidental or indirect damages (including without limitation attorneys fees and expenses), nor shall Seller be liable for any loss of profit or material arising out of or relating to the sale or operation of the products based on contract, tort (including negligence), strict liability or otherwise.
Shipping Damage or Loss If equipment is damaged or lost in transit, file a claim at once with the delivering carrier. The carrier has signed the Bill of Lading acknowledging that the shipment has been received from the seller in good condition. Seller is not responsible for the collection of claims or replacement of materials due to transit shortages or damages.
Warranty Claim Warranty claims must have a Returned Goods Authorization (RGA)from the Seller before returns will be accepted.
Claims for shortages or other errors, exclusive of transit shortages or damages, must be made in writing to Seller within ten (10) days after delivery. Failure to give such notice shall constitute acceptance and waiver of all such claims by Buyer.
Safety Waukesha Cherry-Burrell
Page 6 95-03009 10/2010
SafetyREAD AND UNDERSTAND THIS MANUAL
PRIOR TO INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT
Waukesha Cherry-Burrell recommends users of our equipment and designs follow the latest Industrial Safety Stan-dards. At a minimum, these should include the industrial safety requirements established by:
1. Occupational Safety and Health Administration (OSHA), Title 29 of the CFRSection 1910.212- General Requirements for all Machines
2. National Fire Protection Association, ANSI/NFPA 79ANSI/NFPA 79- Electrical Standards for Industrial Machinery
3. National Electrical Code, ANSI/NFPA 70ANSI/NFPA 70- National Electrical CodeANSI/NFPA 70E- Electrical Safety Requirement for Employee Workplaces
4. American National Standards Institute, Section B11
Attention: Servicing energized industrial equipment can be hazardous. Severe injury or death can result from electri-cal shock, burn, or unintended actuation of controlled equipment. Recommended practice is to disconnect and lockout industrial equipment from power sources, and release stored energy, if present. Refer to the National Fire Protection Association Standard No. NFPA70E, Part II and (as applicable) OSHA rules for Control of Hazardous Energy Sources (Lockout-Tagout) and OSHA Electrical Safety Related Work Practices, including procedural requirements for:
Lockout-tagout
Personnel qualifications and training requirements
When it is not feasible to de-energize and lockout-tagout electrical circuits and equipment before working on or near exposed circuit parts
Locking and Interlocking Devices: These devices should be checked for proper working condition and capability of performing their intended functions. Make replacements only with the original manufacturers renewal parts or kits. Adjust or repair in accordance with the manufacturers instructions.
Periodic Inspection: Industrial equipment should be inspected periodically. Inspection intervals should be based on environmental and operating conditions and adjusted as indicated by experience. At a minimum, an initial inspection within 3 to 4 months after installation is recommended. Inspection of the electrical control systems should meet the rec-ommendations as specified in the National Electrical Manufacturers Association (NEMA) Standard No. ICS 1.3, Pre-ventative Maintenance of Industrial Control and Systems Equipment, for the general guidelines for setting-up a periodic maintenance program.
Replacement Equipment: Use only replacement parts and devices recommended by the manufacturer to maintain the integrity of the equipment. Make sure the parts are properly matched to the equipment series, model, serial num-ber, and revision level of the equipment.
Warnings and cautions are provided in this manual to help avoid serious injury and/or possible damage to equipment:
DANGER: marked with a stop sign.Immediate hazards which WILL result in severe personal injury or death.
WARNING: marked with a warning triangle.Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION: marked with a warning triangle.Hazards or unsafe practices which COULD result in minor personal injury or product or property damage.
Waukesha Cherry-Burrell Care of Stainless Steel
10/2010 95-03009 Page 7
Care of Stainless Steel
Stainless Steel Corrosion Corrosion resistance is greatest when a layer of oxide film is formed on the surface of stainless steel. If film is disturbed or destroyed, stainless steel becomes much less resistant to corrosion and may rust, pit or crack.
Corrosion pitting, rusting and stress cracks may occur due to chemical attack. Use only cleaning chemicals specified by a reputable chemical manufacturer for use with 300 series stainless steel. Do not use excessive concentrations, temperatures or exposure times. Avoid contact with highly corrosive acids such as hydrofluoric, hydrochloric or sulfuric. Also avoid prolonged contact with chloride-containing chemicals, especially in presence of acid. If chlorine-based sanitizers are used, such as sodium hypochlorite (bleach), do not exceed concentrations of 150 ppm available chlorine, do not exceed contact time of 20 minutes, and do not exceed temperatures of 104F (40C).
Corrosion discoloration, deposits or pitting may occur under product deposits or under gaskets. Keep surfaces clean, including those under gaskets or in grooves or tight corners. Clean immediately after use. Do not allow equipment to set idle, exposed to air with accumulated foreign material on the surface.
Corrosion pitting may occur when stray electrical currents come in contact with moist stainless steel. Ensure all electrical devices connected to the equipment are correctly grounded.
Elastomer Seal Replacement Following Passivation
Passivation chemicals can damage product contact areas of WCB equipment. Elastomers (rubber components) are most likely to be affected. Always inspect all elastomer seals after passivation is completed. Replace any seals showing signs of chemical attack. Indications may include swelling, cracks, loss of elasticity or any other noticeable changes when compared with new components.
Introduction Waukesha Cherry-Burrell
Introduction
Manual Content Maintenance procedures in this manual do not cover aseptic or high pres-sure pump applications. These are covered in special addendums avail-able from your Waukesha Cherry-Burrell representative.
Receiving Your Pump All ports are covered at the factory to keep out foreign objects during tran-sit. If the covers are missing or damaged, thoroughly inspect the fluid head, by removing the pump cover (if applicable). Be sure that the pump-ing head is clean and free of foreign material before rotating the shaft. Each Waukesha pump is shipped completely assembled, lubricated, and ready for use. Make sure you review Operation on page 30 before oper-ating your pump.
Receiving and Inspection1. WCB equipment is inspected prior to shipment. When leaving the fac-
tory, it is well-crated for normal transportation procedures. WCB can-not, however, guarantee safe arrival. Therefore, upon receipt of this equipment, check the received items against the packing list for dam-aged or missing parts. Check the packing material thoroughly for small parts.
2. Visually inspect for damage or loss. Immediately report any damage or loss to the delivery carrier while present. Following the immediate notification of the lost or damaged parts, make a claim against the carrier including a detailed description of the loss or damage, and a cash value. WCB's responsibility terminates F.O.B. point of manufac-ture unless otherwise specified per the General Terms and Condi-tions of Sale as published by WCB and amended from time to time. Contact WCB Order Services if shipping information is required for handling claims.
See also Shipping Damage or Loss on page 5.Page 8 95-03009 10/2010
Waukesha Cherry-Burrell Introduction
Pump Characteristics The Waukesha 200 Series Pump is built for extremely durable service.
The casing, backplate and impeller/stub shaft are cast 316L stainless steel for extra strength and resistance to line shock and corrosion. Large bearings and shaft provide positive alignment and minimize vibration.
The casing is clamped to the motor adapter bracket (close coupled) or bearing housing (base mount) for easy disassembly while permitting 360 degree rotation of the discharge port.
200 Series pumps are available with three standard seal types:
Type 1: Single mechanical seal, externally-mounted and balanced.
Type 1C: Single mechanical seal with water cascade flush.
Type 4: Double mechanical seal with flush housing.
All seal components are interchangeable between models. All seal assemblies use an externally-mounted, balanced rotary seal for longer seal life and better sealing capability. The stationary seal face is revers-ible and replaceable.
200 Series pumps are designed for a broad range of sanitary and indus-trial applications. Sanitary models are designed for clean-in-place and meet U.S.D.A. and 3A Standards.
200 Series Base Mount Description
The Waukesha 200 Series Modular Base Mounted Centrifugal Pump design consists of four components (in addition to pump and motor). These components are used in various combinations and arrangements to provide flexibility to meet various needs.
Base Mount ComponentsBearing Housing (Pump Adapter) The bearing housing is made of epoxy-coated cast iron with 316 SS
shaft, ball bearings.
The adapter mounts to the pump components (the same components are used for close coupled pumps).
The bearing housing also includes a coupling for the motor shaft plus guards used in style "C" arrangements.
Style "C" ArrangementThe style "C" arrangement is composed of the bearing housing and base with the stand attached to the bearing housing, for use with foot-mounted T-frame motors. The pump and motor are mounted and supported independently. (Figure 1).
Motor Adapter The motor adapter is made of epoxy-coated cast iron.
The motor adapter is used to mount a standard NEMA C-face motor onto the bearing housing.
The motor adapter is used to provide an accurate, rigid shaft alignment.
Figure 1 - Style C10/2010 95-03009 Page 9
Introduction Waukesha Cherry-Burrell
Stand The stand (pedestal) is made of epoxy-coated cast iron.
The stand attaches under the motor adapter or bearing housing.
Base (Optional) The epoxy-coated channel base is used in style "C" arrangements.
See Table of Base Size Used On Modular Base Mounted Centrifugal Pumps on page 20.
Figure 2 - Common Part Identification
A. Motor Shims H. O-ring
B. Motor Adapter J. Impeller
C. Lock Washer K. O-ring
D. Cap Screws L. Impeller Retainer
F. Seals (detail not shown) M. Clamp
G. Backplate N. CasingPage 10 95-03009 10/2010
Waukesha Cherry-Burrell IntroductionFigure 3 - Type 1 Seal Assembly (Water Cascade Type 1C)
CT100-063
A
B
C
DE
FG H
J
K
L
M
A. Motor Shims G. Rotary Seal
B. Deflector H. Cap Screws
C. Spring Retainer J. Seat Retainer
D. Springs K. Stationary Seal
E. Tabbed Washer L. L-gasket
F. O-ring M. Water Cascade Block10/2010 95-03009 Page 11
Introduction Waukesha Cherry-BurrellFigure 4 - Type 4 Seal Assembly
CT100-064b
16 22 82
5
910
6, 7 1110
95
28
1713
121415
2. Stationary Seal 12. Housing O-ring
5. Rotary Seal 13. Seal Housing
6. Set Screw 14. Seal Retainer
7. Spring Retainer 15. Cap Screws
8. L-gasket 16. Slinger
9. Seal O-ring 17. NPT Plug
10. Tabbed Washer 22. Motor Shims
11. Springs Page 12 95-03009 10/2010
Waukesha Cherry-Burrell Introduction
Performance Characteristics
Authorization3A/USDA (Sanitary Models)/EHEDG
Standard Construction Casing: 316L Stainless Steel
Port Connections: S-Line
Backplate: 316L Stainless Steel
Impeller W/Integral Shaft: 316L Stainless Steel
Impeller Retainer: 316L Stainless Steel
Shaft Seal: Single Mechanical, external balanced (Type 1)
Rotary Seal Material: Carbon
Stationary Seal: Siliconized Graphite
Elastomers: FDA approved FKM
Finish: All product contact surfaces are provided with a sanitary polish (150 Grit). Industrial pumps are unpolished.The motor adapter bracket is painted with a cast iron paint; a two-part epoxy, TNEMEC 104, Sky-Blue #104-BB-42 on the motor bracket and motor (if ordered).
Mounting: Close coupled for JM shafted motors
Construction OptionsPorts
Bevel SeatFemale I-LineMale I-LineQ-LineButt-weldFemale or Male N.P.T150 Lb. Flange, DIN or SMS
Seal Type Water Cascade (Type 1C) Double Mechanical w/flush (Type 4 Shaft Seal) WFI - Special Type 4 shaft seal for water for injection applications Aseptic Shaft Seal - barrier flush design Commercially available seals (Contact your WCB representative for
details)Rotary Seal Material
PurebideSilicone CarbideTungsten Carbide
Stationary Seal Silicone CarbideTungsten Carbide10/2010 95-03009 Page 13
Introduction Waukesha Cherry-Burrell
Elastomers
EPDM (FDA approved)Silicone (FDA approved)Teflon Encapsulated (FDA approved)FFKM
Finishes/Product Contact Surfaces 25RA 20RA ElectropolishUnpolished - Industrial
Leg KitSee Motor Mounts on page 70.
Base Mounting Footless C-face motorsFooted C-face motorsT-Frame motors NOTE: T-Frame motors can be configured with or without bases, couplings or coupling covers.
Pedestal MountedTwo types on stands; see Base Mount Components on page 9.
MotorsNEMA JM (standard) totally enclosed fan cooled (TEFC) for close-coupled pumps
1750 or 3500 RPM single phase 115/230 volt and 3 phase 230/460 volt
Optional EnclosuresWashdownExplosion proofSevere Duty/Chemical Duty
Operating Parameters Nominal CapacityUp to 1150 U.S. GPM (260 Cubic Meters/Hr.)
Viscosity Up to 1500 CPS
Differential PressureUP to 340 Feet (100 Meters)
TemperatureUp to 450F (230C)
Nominal Speeds1450 or 2900 RPM - 50HZ1750 or 3500 RPM - 60HZ Page 14 95-03009 10/2010
Waukesha Cherry-Burrell Introduction
Capacities
Sanitary Model
Inlet Size inch (mm)
Maximum impeller Size
inch (mm)
Maximum Capacity GPM (M3/HR)
20451.5 (40) 4.5 (115) 190 GPM (43)
2.0 (50) 4.5 (115) 190 GPM (43)
2065LV
1.5 (40) 6.5 (165) 200 GPM (45)
2.0 (50) 6.5 (165) 200 GPM (45)
2.5 (65) 6.5 (165) 200 GPM (45)
2065 2.5 (65) 6.5 (165) 400 GPM (91)
2065HV 3.0 (75) 6.5 (165) 500 GPM (114)
2075 3.0 (75) 8.7 (221) 143 GPM (33)
2085LV 2.0 (50) 8.7 (221) 143 GPM (33)
20853.0 (75) 8.7 (221) 840 GPM (191)
4.0 (100) 8.7 (221) 840 GPM (191)
21054.0 (100) 10.5 (265) 1400 GPM (318)
6.0 (150) 10.5 (265) 1400 GPM (318)10/2010 95-03009 Page 15
Introduction Waukesha Cherry-Burrell
Dimensions
Figure 5 - Footprint Dimensions
B
F
G
D
X
YAA
AB
AE
Z
CT100-046
CP
Sanitary Model Size (Inlet x Outlet)
Motor Frame
2045All
2065LVAll
20652-1/2x2
2065HV3x2
2085LV2x1-1/2
20752x1-1/2
20853x2-1/2
20854x2-1/2
21054x4
21056x4
Dim.Callout
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
CPinch(mm)
145JM 18.94(481)16.35(415)
16.94(430)
17.04(433)
16.16(410)
16.16(410)
17.50(445)
17.05(433) -- --
182JM 21.81(554)19.66(500)
20.25(514)
20.35(517)
18.09(459)
18.09(459)
19.43(494)
18.96(482) -- --
184JM -- 19.66(500)20.25(514)
20.35(517)
18.09(459)
18.09(459)
19.43(494)
18.96(482)
25.13(638)
25.16(639)
213JM -- 21.91(557)22.50(572)
22.60(574)
21.72(552)
21.72(552)
23.05(585)
22.55(573)
23.88(607)
23.91(607)
215JM -- 21.91(557)22.50(572)
22.60(574)
21.72(552)
21.72(552)
23.05(585)
22.55(573)
26.56(675)
26.59(675)
254JM -- 25.47(647)26.06(662)
26.17(665)
25.53(648)
25.53(648)
26.87(682)
26.43(671)
27.63(702)
27.66(703)
256JM -- -- 27.81(706)27.92(709)
25.53(648)
25.53(648)
26.87(682)
26.43(671)
29.38(746)
29.41(747)
284JM -- -- -- 28.44(722)27.66(703)
27.66(703)
29.00(737)
28.50(724)
29.94(760)
29.97(761)
286JM -- -- -- 29.94(760)29.16(791)
29.16(791)
30.50(775)
30.00(762)
31.44(799)
31.47(799)
324JM -- -- -- -- 29.97(761)29.97(761)
31.31(795)
30.81(782)
31.63(803)
31.66(804)
326JM -- -- -- -- 31.47(799)31.47(799)
32.81(833)
32.31(821)
32.87(835)
32.91(836)Page 16 95-03009 10/2010
Waukesha Cherry-Burrell IntroductionTable of Dimensions
FrameA
inch(mm)
Binch(mm)
Dinch(mm)
AAinch(mm)
ABinch(mm)
Finch(mm)
Einch(mm)
Ginch(mm)
145JM 8.56(218)6.87(174)
3.5 (89)
.50(13)
5.25(133)
12.50(317)
5.50(140)
182JM 9.81(249)8.44(214)
4.50(114)
.75(19)
5.87(149)
12.50(317)
7.50(190)
184JM 9.81(249)8.44(214)
4.50(114)
.75(19)
5.87(149)
12.50(317)
7.50(190)
2.00(51)
213JM 12.18(309)10.06(256)
5.25(133)
.75(19)
7.38(187)
12.50(317)
8.25(209)
215JM 12.18(309)10.06(256)
5.25(133)
.75(19)
7.38(187)
16.0(406)
8.25(209)
254JM 14.68(373)12.0(305)
6.25(159)
1.0(25.4)
8.94(227)
16.0(406)
10.0(254)
256JM 14.68(373)12.0(305)
6.25(159)
1.0(25.4)
8.94(227)
25.5(648)
10.0(254)
284JM 18.87(225)13.63(346)
7.0(178)
1.5(38)
12.25(311)
25.5(648)
11.0(279)
286JM 18.87(225)13.63(346)
7.0(178)
1.5(38)
12.25(311)
25.5(648)
11.0(279)
2.50(64)
324JM 20.75(527)15.56(395)
8.0(203)
1.5(38)
13.18(335)
25.5(648)
12.5(317)
326JM 20.75(527)15.56(395)
8.0(203)
1.5(38)
13.18(335)
25.5(648)
12.5(317)
NOTE: Figure 5 dimensions for the Inlet, Outlet, items X,Y, and Z are listed in Table of Dimensions on page 18.10/2010 95-03009 Page 17
Introduction Waukesha Cherry-BurrellTable of Dimensions
Model(**)
Inletinch(mm)
Outletinch(mm)
Xinch(mm)
Yinch(mm)
Zinch(mm)
2045 1.5(40)1.5(40)
3.88(98)
1.81(46)
2.25(57)
2045 2.0(50)1.5(40)
3.88(98)
1.81(46)
2.25(57)
2065LV 1.5(40)1.5(40)
4.75(120)
1.94(49)
3.19(81)
2065LV 2.0(50)1.5(40)
4.75(120)
1 94(49)
3.19(81)
2065LV 2.5(65)1.5(40)
4.75(120)
1.94(49)
3.19(81)
2065 2.5(65)2.0(50)
4.44(113)
1.94(49)
3.94(100)
2065HV 3.0(75) 2.0(50)
4.44(113)
1.94(49)
3.94(100)
2075 3.0(75)1.5(40)
6.69(170)
1.75(44)
4.5(114)
2085LV 2.0(50)1.5(40)
6.69(170)
1.75(44)
4.5(114)
2085 3.0(75)2.5(65)
5.63(143)
2.53(64)
5.06(129)
2085 4.0(100)2.5(65)
5.63(143)
2.03(52)
5.06(129)
2105 4.0(100)4.0
(100) 6.94(176)
2.86(73)
6.75(171)
2105 6.0(150)4.0
(100)6.94(176)
2.90(74)
6.75(171)Page 18 95-03009 10/2010
Waukesha Cherry-Burrell IntroductionFigure 6 - Style "B" and "C" Less Base Plate
CT100-065
B Y Z
X
D
6.54 Sm Bore10.47 Lg Bore
3.45 Sm Bore5.74 Lg Bore
4.500 Sm Bore6.85 Lg Bore
1 (1/4 keyway) Sm Bore1.25 (1/4 keyway) Lg Bore
.56 Dia
6.25 Sm Bore9.50 Lg Bore
B D
ModelInletinch(mm)
Outletinch
Sm Boreinch
Lg Boreinch
Sm Boreinch
Lg Boreinch
Xinch
Yinch
Zinch
P2045 1.5(40)1.5(40)
16.39(416) --
3.0 (76) --
3.88(98)
1.81(45)
2.25(57)
P2045 2.0(50)1.5(40)
16.39(416) --
3.0(76) --
3.88(98)
1.81(45)
2.25(57)
P2065LV 1.5(40)1.5(40)
16.71(224) --
2.0(50)
5.2(132)
4.75(120)
1.94(49)
3.19(81)
P2065LV 2.0(50)1.5(40)
16.71(224) --
2.0(50)
5.2(132)
4.75(120)
1.94(49)
3.19(81)
P2065LV 2.5(65)1.5(40)
16.71(224) --
2.0(50)
5.2(132)
4.75(120)
1.94(49)
3.19(81)
P2065 2.5(65)2.0(50)
17.30(439) --
2.0(50)
5.2(132)
4.44(112)
1.94(49)
3.94(100)
P2065HV 3.0(75)2.0(50)
17.93 (455)
21.30(541)
2.0(50)
5.2(132)
4.44(112)
1.94(49)
3.94(100)
P2075 3.0(75)1.5(40)
17.19(436)
20.42(581)
1.0(25)
4.2(106)
6.69(176)
1.75(44)
4.50(114)
P2085LV 2.0(50)1.5(40)
17.19(436)
20.42(581)
1.0(25)
4.2(106)
6.69(176)
1.75(44)
4.50(114)
P2085 3.0(75)2.5(65)
18.41(467)
21.90(556)
1.0(25)
4.2(106)
5.63(143)
2.53(64)
5.06(128)
P2085 4.0(100)2.5(65)
17.91(454)
21.40(543)
1.0(25)
4.2(106)
5.63(143)
2.03(51)
5.06(128)
P2105 4.0(100) -- -- 22.57(573) --
3.2(81)
6.94(176)
2.86(72)
6.75(171)
P2105 6.0(150) -- --22.60(574) --
3.2(81)
6.94(176)
2.90(73)
6.75(171)
NOTE: Dimensions X,Y, and B apply to pumps with clamp connections.10/2010 95-03009 Page 19
Introduction Waukesha Cherry-BurrellTable of Base Size Used On Modular Base Mounted Centrifugal Pumps
Motor HP & RPMSanitary Models
P2045 P2065LV P2065 P2065HV P2075 P2085LV P2085 P2105
Up to 5HP 1750 RPM SM.B. SM.B. SM.B. SM.B. SM.B. SM.B. SM.B. SM.B.
Up to 5HP 3500 RPM SM.B. SM.B. SM.B.
7HP 1750 RPM SM.B. LG.B.
7HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B. SM.B.
10HP 1750 RPM SM.B. LG.B.
10HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B. SM.B.
15HP 1750 RPM LG.B.
15HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B.
20HP 1750 RPM LG.B.
20HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B.
25HP 1750 RPM LG.B.
25HP 3500 RPM LG.B. LG.B.
30HP 1750 RPM LG.B.
30HP 3500 RPM LG.B. LG.B.
40HP 1750 RPM LG.B.
40HP 3500 RPM LG.B.
50HP 1750 RPM LG.B.
50HP 3500 RPM LG.B.
60HP 3500 RPM LG.B.
75HP 3500 RPM LG.B.
SM.B. = Small Base
LG.B. = Large Base Page 20 95-03009 10/2010
Waukesha Cherry-Burrell IntroductionFigure 7 - Base Plate Dimensions for Modular Base-Mounted Centrifugal Pumps
Width
Length
Base plates (optional) are provided in three widths and five lengths (depending on motor frame and pump model).
Widths Available:
10 inches15 inches18 inches
Lengths Available:
20 inches (Style A Only)24 inches32 inches38 inches50 inches10/2010 95-03009 Page 21
Introduction Waukesha Cherry-Burrell
Centrifugal 200 Series Pump and Pedestal Weights
Figure 8 - Close-Coupled Pump (Less Motor and Legs)
Motor Frame
Pump Model
2045LBS(KG)
2065LVLBS(KG)
2065LBS(KG)
2065HVLBS(KG)
2075LBS(KG)
2085LVLBS(KG)
2085LBS(KG)
2105LBS(KG)
142-184JM 21(9.5)31
(14)33
(14.9) 35
(15.8)57
(25.8)57
(25.8)51
(23.1)60
(27.2)
213-215JM 35(15.8)37
(16.7)39
(17.6)60
(27.2)54
(24.4)54
(24.4)78
(35.3) --
254-256JM 37(16.7)39
(17.6)41
(18.5)63
(28.5)57
(25.8)57
(25.8)79
(35.8) --
284-326JM 51(23.1)53
(24)71
(32.2)64
(29)82
(37.1)82
(37.1) -- --
Add 5LB. For Pumps With Double Seals
Add Listed Weight for Legs
Motor Frame WeightlBS (KG)
142-213JM 10.5 (4.7)
215-254JM 12.5 (5.6)
254-326JM 42.5 (19.2)
Figure 9 - Legs Page 22 95-03009 10/2010
Waukesha Cherry-Burrell IntroductionFigure 10 - Pedestal Pump (Less Base and Motor)
Pump Model
PEDESTAL2045lbs
(KG)
2065LVlbs
(KG)
2065lbs
(KG)
2065HVlbs
(KG)
2075lbs
(KG)
2085LVlbs
(KG)
2085lbs
(KG)
2105lbs
(KG)
SMALL BORE 92(41) 106 (48)108
(48.9) 110
(49.8)131
(59.4)131
(59.4)125
(56.6) --
LARGE BORE -- -- -- -- -- -- 235 (106.5)240
(108.8)
Figure 11 - Base Weight (add to Pedestal Weight)
MOTORSMALLBORE
LBS (KG)
LARGEBORE
LBS (KG)
48 30 (13.6) --
56 30 (13.6) --
143/145T 31 (14.6) --
182/184T 32 (14.5) 50 (22.6)
213/215T 33 (14.9) 50 (22.6)
254/256T 40 (18.1) 52 (23.5)
284/286T 35 (15.8) 62 (28.1)
284/286TS -- 64 (29.0)
324/326T -- 65 (29.4)
324/326TS -- 65 (29.4)
364TS -- 65 (29.4)10/2010 95-03009 Page 23
Installation Waukesha Cherry-Burrell
Installation
Pump Location Consider the following when determining a location for the installation of your pump:
Locate the pump as near as is practical to the liquid supply.
Keep the supply piping short and straight to keep the pump supplied with liquid and prevent damaging cavitation.
Make sure the pump is accessible for service and inspection during operation.
Protect the motor from flooding.
Pump LevelingLevel the pump by loosening the set screws (Figure 12, item A) to adjust the length of the legs.
Supply and Discharge Piping/Valves
Consider the following when determining supply/discharge piping and valve installation of your pump:
Use a line size equal to or larger than the connection size on the pump, especially the inlet supply line.
Keep the supply line as short and straight as possible and use as few elbows, valves, or other types of restriction as possible. Avoid up and down rises which will trap air.
Be certain all joints in the suction line are well-sealed to prevent air leaks.
Maintain a straight length of pipe (Figure 13, item A) at least 8 diameters long at the pump inlet.
Figure 12 - Leveling Leg Set Screw Location
Figure 13 - Straight Pipe Length Page 24 95-03009 10/2010
Waukesha Cherry-Burrell Installation
The pump casing may be rotated with the discharge connection
pointing in any direction. The best pump performance will be with the outlet up, to the left, or positions in between; these positions ensure a flooded casing and prevent problems caused by air in the system (Figure 14).
All joints in the suction line must be well-sealed to prevent air from being sucked into the system.
Support the supply and discharge piping near the pump so that no strain is put on the pump casing.
If an expansion joint is used, install a pipe anchor between the joint and the pump.
If a reducer is connected to an inlet, use an eccentric-type reducer to prevent problems caused by trapped air (Figure 16).
CAUTION: The pump and piping may contain sharp edges. Wear gloves while installing and servicing the pump to help avoid injuries from these hazards.
The line slope will depend on application requirements; the best pump operation is with the supply line sloped slightly upward toward the pump to prevent trapping air. If the system must drain into the pump casing, keep the downward slope to a minimum or priming problems may occur.
Install shutoff valves to isolate the pump from the supply and discharge lines. This will allow the pump to be serviced without draining the system.
Figure 14 - Recommended Discharge Positions
Figure 15 - Pipe Supports
Figure 16 - Correct Eccentric Installation10/2010 95-03009 Page 25
Installation Waukesha Cherry-Burrell
Installations That May Cause Operation Problems This pump is not self priming. If the pump is installed above the
supply liquid level, install a foot valve or other system check valve to keep the system flooded for priming (Figure 17, item A)
A throttling valve may be required to control the pump flow rate to prevent motor overload. Always install the throttling valve (Figure 17, item B) in the discharge piping, at least 10 pipe diameters from the pump outlet.
Never install a throttling valve in the supply piping (Figure 17, item C).
Any system throttling valves or similar devices to control the flow rate must be installed in the discharge line. Do not install any system throttling valves or similar devices to control the flow rate in the supply line. Restriction in the supply line may cause cavitation and pump damage.
Water hammer in the system can damage the pump and other system components. Water hammer often occurs when valves in the system are suddenly closed, causing lines to move violently and with a loud noise. When this condition is present, find and eliminate the source of the water hammer. One way to eliminate water hammer is to slow down the actuation speed of the valve.
Do not expose the pump to freezing temperatures with liquid in the casing. Frozen liquid in the casing will damage the pump. Drain the casing before exposing it to freezing temperatures.
Electrical Connections WARNING: To avoid electrocution, ALL electrical installation should be done by a registered Electrician, following Industry Safety Standards. All power must be OFF and LOCKED OUT during installation.
Read the motor manufacturer's instructions before starting the installation. Follow the manufacturer's lubrication schedules.
Check the motor nameplate to be sure the motor is compatible with the electrical supply and all wiring, switches, and starters. Make sure all overload protections are correctly sized (Figure 18).
Check the pump rotation following the electrical installation. The correct rotation is counterclockwise when facing the pump inlet connection (Figure 14 and Figure 18).
Figure 17 - Valve Piping Installation
Figure 18 - Direction of Motor RotationPage 26 95-03009 10/2010
Waukesha Cherry-Burrell Installation
Flush Seal Option When this option is ordered, a fitting assembly (Figure 19, item A) is sup-
plied for directing a flow of water onto the backplate/seal area. The water cascade block must be above the seal on the assembled
backplate to flow water onto the seal face.
The connection (Figure 19, item B) is 1/4 inch O.D. tubing.
The required flow is approximately 5 U.S. gallons per hour.
The recommended water supply is cool and filtered. If the product solidifies at a cool temperature, warm or hot water can be used.
NOTE: To prevent hose contact with the rotating shaft and seal parts dur-ing operation, pull the excess hose to the outside of the adapter.
Type 4 Seal (Double mechanical with flush)Attach the seal flush supply to the bottom 1/4-inch pipe-threaded hole in the flush housing. The drain tubing attached to the top hole allows moder-ate pressure to be supplied to the seals and allows continuous flooding. (Figure 20).
Figure 19 - Cascade System Installation
Figure 20 - Type 4 Flush Housing10/2010 95-03009 Page 27
Installation Waukesha Cherry-Burrell
Before First Startup Clean Pump and Piping
Disassemble the pump and clean all product contact parts and seal parts prior to the first operation. Follow the instructions in the Cleaning Safety Procedures, below and Routine Maintenance on page 32. Thoroughly clean the pump of any materials which could have accumulated during installation.
Cleaning Safety Procedures
Manual CleaningAddress the following recommendations when manually cleaning your pump:
Do not use toxic and/or flammable solvents.
Lock out electrical power and shut off all air prior to cleaning the equipment.
Keep electrical panel covers closed and power off when washing the equipment.
WARNING: To prevent an accidental start-up, lock out the power source with lock and key.
Clean up spills as soon as possible.
Never attempt to clean the equipment while it is operating.
Wear proper protective clothing.
Cleaning-In-Place (CIP)When performing CIP:
1. Make certain that all connections in the cleaning circuit are properly applied and tight to avoid contact with hot water or cleaning solutions.
2. When the cleaning cycle is controlled from a remote or automated cleaning center, establish safe procedures to avoid automatic start-up while servicing equipment in the circuit.
NOTE: Always replace the o-rings when reassembling the pump. If the area behind these seals becomes soiled, contact WCB Application Engi-neering for a specific cleaning and sanitizing procedure validated to remove bacteria.Page 28 95-03009 10/2010
Waukesha Cherry-Burrell Installation
Preliminary Test Run Test the system using a preliminary run with the materials that will be
pumped. DO NOT run the pump at this time to produce final product.
See Starting the Pump on page 30.
Check For Possible Motor Overload ConditionsCertain combinations will overload the motor when operated with open unrestricted discharge, resulting in an unacceptably high flow rate. Addi-tional discharge restriction may be required to lower the flow rate and lower the horsepower requirement. DO NOT add a restriction to the sup-ply line. If the pump was incorrectly selected, a smaller impeller or a higher motor horsepower may be required.
If you are uncertain about pump selection and application, temporarily install an ammeter in the electrical service.
Ammeter Test
WARNING: To avoid electrocution and equipment damage, only a qualified electrician should install the ammeter.
Operate the pump under process conditions and check the motor amp draw versus the nameplate full load rating. If the amp draw exceeds the motor rating, a system change or pump change is required.
If the process conditions and/or liquid changes (higher viscosity, higher specific gravity), recheck the motor amp draw.10/2010 95-03009 Page 29
Operation Waukesha Cherry-Burrell
Operation Before proceeding, make sure your pump has been correctly installed as
described in Installation on page 24.
Starting the Pump 1. If the pump has a flush seal option, start the flow of flush water (approximately 5 US gallons per hour recommended rate) before operating the pump.
2. Before starting the pump, prime the pump by flooding the pump cas-ing with liquid, to avoid damage to pump parts. See Priming the Pump With the Feed Source Above Pump Level on page 30 or Priming the Pump With the Feed Source Below Pump Level on page 31.
3. Start the pump motor.
4. Check the pump to see that liquid is flowing and that all piping con-nections and seals are leak-free.
5. Make sure that the pump is not operating against a closed discharge. Continued operation against a closed discharge will heat the liquid in the casing to boiling and lead to pump damage.
6. Slowly open the discharge valve until the desired flow is obtained. Observe the pressure gauges and if pressure is not attained quickly, stop the pump and prime it again.
Priming the Pump/Stopping the Pump
Priming the Pump With the Feed Source Above Pump Level
1. Fill the supply tank with liquid; open the supply line (suction) valve (Figure 21, item B).
2. Vent any air trapped in the supply line or casing by opening the dis-charge valve (Figure 21, item A).
3. Start the pump.
Figure 21 - Pump Below Supply (Feed Source Above Pump Level)Page 30 95-03009 10/2010
Waukesha Cherry-Burrell Operation
Priming the Pump With the Feed Source Below Pump LevelThe pump will not self-prime if the liquid supply is below the pump level. When the liquid supply is below the pump level, an outside source must be provided for priming.
1. Close the discharge valve (Figure 22, item C) and open the air vents.
2. Open the valve installed in the outside supply line (Figure 22, item A) until liquid flows from vent valves.
3. Close the vent valves.
4. Close the outside supply line.
NOTE: Use a check valve system (Figure 22, item B) to keep the supply line and pump casing flooded with liquid; otherwise the pump must be primed before each operation.
Stopping the Pump1. To stop the pump, shut off power to the pump motor.
NOTE: Liquid in the system can flow freely through the pump; the pump does not act as a shutoff valve.
2. Shut off supply and discharge lines.
Figure 22 - Pump Above Supply(Feed Source Below Pump Level)10/2010 95-03009 Page 31
Maintenance Waukesha Cherry-Burrell
Maintenance
Scheduled Maintenance A routine maintenance program can extend the life of your pump. Make sure to keep maintenance records. These records will help pinpoint potential problems and causes.
Routine MaintenanceYour scheduled routine maintenance should include the following items:
Check for unusual noise, vibration, and bearing temperatures
Inspect the pump and piping for leaks
Check the Mechanical Seal area for leakage(No leakage is desired)
Check the backplate gasket for wear/damage
Bearing lubrication (See motor manufacturer for correct specifications)
Seal Monitoring
Vibration analysis
Check the discharge pressure
Temperature monitoring
Disassembly of Pump With a Type 1 Seal
1. Shut off the product flow to the pump and relieve any product pres-sure.
2. Shut off and lock out power to the pump.
3. Disconnect the suction and discharge pipe fittings. 4. Remove the casing clamp and casing.
5. Slide the o-ring off of the backplate.
6. Remove the impeller retainer bolt and shaft o-ring.
NOTE: The retainer bolt has standard right-hand threads.
Removal of the Water Cascade1. Loosen the socket head screws holding the water cascade block on
the stationary seat retainer and remove the plastic hose.
2. Pull off the impeller/backplate assembly and place it on a clean flat surface with the impeller shaft up.
CAUTION: Handle the impeller/backplate assembly with care to prevent damage to the seal components.
NOTE: If the assembly cannot be removed from the motor shaft by hand, contact Waukesha Cherry-Burrell Customer Service.
Figure 23 - Removal of the Water Cascade SystemPage 32 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
3. Locate the shims on the motor shaft and remove them.
NOTE: Motor shaft shims may fall off the motor shaft or hang up inside the deflector. Be sure to place all shims back on the motor shaft.
4. Remove the deflector (Figure 24, item B).
5. Loosen the two (2) set screws (Figure 24, item D) in the spring retainer (item C) and slide the retainer and washer (item F) off the shaft. Save the three (3) springs (item E).
6. Use the backplate to slide the rotary seal up the impeller shaft approximately 1-1/2 inches (Figure 25).
7. With the backplate resting on the impeller, push the rotary seal toward the backplate until the o-ring is free (Figure 26).
8. Remove the o-ring, then lift the rotary seal off the shaft (Figure 24, items G and H).
9. Lift the backplate off the impeller.
CAUTION: To avoid seal failure, DO NOT place fingers on the car-bon seal face.
Figure 24 - Type 1 Seal Items
Figure 25 - Moving Rotary Seal Up the Shaft
Figure 26 - Push Rotary Seal Down10/2010 95-03009 Page 33
Maintenance Waukesha Cherry-Burrell
10. Remove the four 1/4" hex bolts and stationary seat retainer ring (Fig-
ure 27, items A and B).
11. Pull the stationary seal and L-gasket out of the backplate (Figure 27, items C and D).
NOTE: The stationary seal is brittle. Prying or hammering on the seal plate can shatter the seal. If the stationary seal cannot be removed by hand, place a 2-1/4 inch diameter plastic or wood rod on the impeller side of the seal and apply even pressure to dislodge the seal.
Inspect Parts Once disassembly is complete, perform the following inspections:
Examine all seal surfaces and replace seals that are scratched, cracked and/or braised.
Inspect all o-rings and o-ring seats for abrasions, cuts or other wear that could cause leakage.
Clean all seat areas and alignment surfaces.
NOTE: Stationary seals are reversible. Use both sides before replacing them.
NOTE: Replace the rotary seal when the seal face extends less than 1/32 inch (1 mm) from the body (Figure 28).
Assembly of Pump With a Type 1 Seal
Backplate Assembly
1. Lightly lubricate both sides of the L-gasket (Figure 29, item D) with a sanitary lubricant and insert it into the backplate seal cavity.
2. Place the stationary seal into the L-gasket (Figure 29, items C and D).
3. Place the seat retainer over the stationary seal and secure the retainer with four 1/4-20 x 1/2 inch hex head cap screws (Figure 29, items B and A).
4. Tighten the cap screws evenly.
Figure 27 - Removing Stationary Seal
Figure 28 - Rotary Seal Replacement Minimum
Figure 29 - Stationary Seal AssemblyPage 34 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
Backplate/Impeller Assembly1. Place the impeller on a clean flat surface, shaft-end up, and slide the
assembled backplate onto the impeller shaft.
NOTE: Avoid hitting the stationary seal against the impeller shaft, as it could break the seal.
2. Carefully place the rotary seal in position over the impeller shaft and down against the stationary seal.
3. Lubricate and slide the seal o-ring onto the impeller shaft. Use the spring retainer as a tool to push the o-ring into the rotary seal (Figure 30).
4. Slide the tabbed washer (Figure 29, item F) over the impeller shaft and engage the tabs of the washer into notches on the outside of the rotary seal (Figure 31, items F and H).
5. Install the three seal springs into the holes in the spring retainer (Fig-ure 31, items C and E). Hold the springs in place with RTV silicone sealant.
6. Slide the spring retainer over the impeller shaft until the slots in the spring retainer engage the drive tabs on the washer and the springs rest against the washer (Figure 31).
7. With the backplate against the impeller, push the spring retainer down to compress the springs until the length of visible spring is approximately 1/8".
8. Lock the spring retainer in place by tightening the set screws (Figure 31, item D).
9. Install the deflector onto the impeller shaft (Figure 31, item B).
10. If your system has a water cascade, thread the water cascade hose through the adapter and install the cascade block on the backplate (Figure 32, items A and B).
11. Slide the motor shims onto the shaft. Use the same number of shims that were removed when the pump was disassembled.
12. Install the impeller assembly on the stub shaft of the motor.
13. Hand-tighten the impeller retainer bolt on the shaft.
Figure 30 - Installing O-ring Using Spring Retainer
Figure 31 - Type 1 Seal Assembly
Figure 32 - Installing Water Cascade System10/2010 95-03009 Page 35
Maintenance Waukesha Cherry-Burrell
14. Check the space between the back of the impeller and the backplate
with a feeler gauge (0.030" nominal) while holding the backplate tight against the bearing housing flange. (Any axial movement of the shaft should not be added to the 0.030" nominal clearance) (Figure 33). If needed, change this clearance by adding or removing shims. Shims (Figure 34, item A) are added on the drive shaft (Figure 34, item C) behind the impeller shaft (Figure 34, item B).
15. Confirm the operating clearances by clamping the casing to the bear-ing housing flange and rotating the shaft/impeller manually to be sure the impeller does not touch the casing or backplate.
16. When the proper shim pack is confirmed, remove the casing, impel-ler, and backplate, leaving the shim pack on the shaft.
17. Remove the backplate/impeller assembly and apply anti-seize or equal compound to the motor shaft and install the key.
NOTE: Always replace the o-rings and L-gasket when reassembling the pump. If the area behind these seals becomes soiled, contact WCB Appli-cation Engineering for a specific cleaning and sanitizing procedure vali-dated to remove bacteria.
18. Install the casing o-ring on the backplate and clamp the casing in place (Figure 35).
NOTE: Rotate the impeller manually to ensure it does not rub on the backplate or casing.
Figure 33 - Clearance Between Impeller and Backplate
Figure 34 - Locations of Shims
Figure 35 - Install Casing Page 36 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
Type 4 Double Seal The Type 4 Seal is essentially two Type 1 seals assembled back to back
in a chamber which bolts to the backplate in place of the stationary seat retainer. Except for the additional components (chamber, seals), Type 1 and Type 4 components are interchangeable (Figure 36).
Disassembly of Type 4 Seal
Figure 36 - Type 4 Seal Components
A B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
T
U
V
CT100-089W F
A. Impeller F. O-ring L. Rotary Seal S. Stationary Seal
B. Backplate G. Washer M. O-ring T. L-gasket
C. L-gasket H. Spring Retainer N. NPT Port U. Seat Retainer
D. Stationary Seal J. Spring P. Flush Housing V. Hex Head Screw (4)
E. Rotary Seal K. Washer R. O-ring W. Set Screw
CAUTION: Handle the impeller/backplate assembly with care to prevent damage to the seal com-ponents.
1. Shut off the product flow to the pump and relieve any product pres-sure.
2. Shut off and lock out power to the pump.
3. Disconnect the suction and discharge pipe fittings.
4. Remove the casing clamp and casing. Slide the o-ring off the back-plate.
5. Remove the impeller retainer bolt and shaft o-ring.
NOTE: The retainer bolt has standard right-hand threads. 10/2010 95-03009 Page 37
Maintenance Waukesha Cherry-Burrell
Removal of the Water CascadeIf your system is equipped with a water cascade system, remove it before proceeding.
1. Loosen the socket head screws holding the water cascade block on the stationary seat retainer and remove the plastic hose.
2. Pull off the impeller/backplate assembly and place it on a clean flat surface with the impeller shaft facing up.
NOTE: If the assembly cannot be removed from the motor shaft by hand, contact Waukesha Cherry-Burrell Customer Service.
3. Locate the shims on the motor shaft and remove them.
NOTE: Motor shaft shims may fall off the motor shaft or hang up inside the deflector. Be sure to place all shims back on the motor shaft.
CAUTION: Handle the impeller/backplate assembly with care to prevent damage to the seal com-ponents.
4. Place the impeller assembly face down (on impeller vanes) and remove the hex head screws (Figure 36, item V) from the back of the seal assembly.
5. Carefully lift off the seat retainer, o-ring, L-gasket, stationary seal, and flush housing (Figure 36, items P, R, T, S and U).
6. Loosen (2) set screws in the spring retainer (Figure 36, items W and H).
7. Lift off rotating seal components See Figure 36:Rotary Seal (item L)O-ring (item M)Washer (item K)Spring Retainer (item H)Springs (there are six springs, 3 up and 3 down) (item J)Washer (item G)
8. Use the backplate to slide the rotary seal up the impeller shaft approximately 1-1/2 inches (Figure 38).
9. With the backplate resting on the impeller, push the rotary seal toward the backplate until the o-ring is free (Figure 39).
10. Remove the stationary seal and L-gasket from the backplate. (Figure 40, items D and C)
NOTE: The stationary seal is brittle. Prying or hammering on the seal plate can shatter the seal. If the stationary seal cannot be removed by hand, place a 2-1/4 inch diameter plastic or wood rod on the impeller side of the seal and apply even pressure to dislodge the seal.
11. Inspect and replace all damaged and worn parts.
Figure 37 - Removal of Water Cascade System
Figure 38 - Move Rotary Seal Up Shaft
Figure 39 - Push Rotary Seal DownPage 38 95-03009 10/2010
Waukesha Cherry-Burrell MaintenanceFigure 40 - Type 4 Seal Components
A B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
T
U
V
CT100-089W F
A. Impeller F. O-ring L. Rotary Seal S. Stationary Seal
B. Backplate G. Washer M. O-ring T. L-gasket
C. L-gasket H. Spring Retainer N. NPT Port U. Seat Retainer
D. Stationary Seal J. Spring P. Flush Housing V. Hex Head Screw (4)
E. Rotary Seal K. Washer R. O-ring W. Set Screw
Assembly of Type 4 Seal
CAUTION: Handle the impeller/backplate assembly with care to prevent damage to the seal com-ponents.
1. Clean all parts and lubricate all elastomer (rubber-like) parts.
2. Install the L-gasket in the backplate (Figure 40, items B and C).
3. Install the L-gasket in the seat retainer (Figure 40, item T).
4. Install the stationary seals (Figure 40, item S) in the L-gaskets.
5. Place the backplate and rotary seal onto the impeller shaft.
6. Temporarily put 0.03" shims between the impeller vane and back plate to a preset clearance. Be sure to remove the shims before final assembly (Figure 41).
7. Place the o-ring (Figure 40, item F) on the shaft and use the spring retainer to push the o-ring into the rotary seal (Figure 42).
8. Place the washer (Figure 40, item G) over the rotary seal with tabs in the outside diameter notches.
9. Place three springs (Figure 40, item J) in one side of the spring retainer (item H). Hold them in place with silicone sealer, and slide the spring retainer (with the springs down) onto the impeller shaft the against the washer.
Figure 41 - Shim Placement 10/2010 95-03009 Page 39
Maintenance Waukesha Cherry-Burrell
10. Place the remaining three (3) springs in the spring retainer.
11. Slide the washer and o-ring (Figure 40, items K and F) onto the shaft against the spring retainer.
12. Use the spring retainer to press the o-ring into the rotary seal.
13. Remove the 1/4 NPT plug from the center port on the flush housing (Figure 40, item N).
14. Install an o-ring (Figure 40, items M and R) in both ends of the hous-ing.
15. Install the L-gasket in the seat retainer (Figure 40, items T and U).
16. Install the stationary seal (Figure 40, item S) in the L-gasket.
17. Install the housing over the seal assembly.
18. With flush ports facing away from the backplate, place the seat retainer (Figure 40, item U) on the housing.
19. Tighten the seat retainer in place with four (4) hex screws (Figure 40, item V).
NOTE: Be sure to tighten the screws evenly until full metal-to-metal con-tact is made on the backplate and seat retainer.
20. Install the original shims on the motor adapter shaft.
21. Install the backplate with the seal assembly and impeller on the motor shaft.
22. Check the impeller/backplate clearance with the backplate held firmly in position against the motor adapter. Check the space between the back of the impeller and the backplate with a feeler gauge (0.030" nominal) while holding the backplate tight against the bearing housing flange. Any axial movement of the shaft should not be added to the 0.030" nominal clearance (Figure 43). If needed, change this clear-ance by adding or removing shims. Shims (Figure 44, item A) are added on the drive shaft (Figure 44, item C) behind the impeller shaft (Figure 44, item B).
23. Confirm the operating clearances by clamping the casing to the bear-ing housing flange and rotating the shaft/impeller manually to be sure the impeller does not touch the casing or backplate.
24. Tighten the set screws in the spring retainer through the 1/4" NPT center port in the flush housing (Figure 40, item N).
25. Insert the plug in the port and tighten it.
26. Remove the backplate/impeller assembly and apply anti-seize or equal compound to the motor shaft and install the key.
27. Install the backplate/impeller assembly and lock it in place using the o-ring and impeller retainer bolt.
Figure 42 - Installing O-ring Using Spring Retainer
Figure 43 - Clearance Between Impeller and Backplate
Figure 44 - Locations of ShimsPage 40 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
NOTE: Always replace the o-rings and L-gasket when reassembling the pump. If the area behind these seals becomes soiled, contact WCB Appli-cation Engineering for a specific cleaning and sanitizing procedure vali-dated to remove bacteria.
28. Install the casing o-ring on the backplate and clamp the casing in place (Figure 45).
NOTE: Rotate the impeller manually to ensure it does not rub on the backplate or casing.
Disassembly of Modular Base-Mounted Pumps
Figure 46 - Removing the Impeller Assembly
Figure 47 - Removing Coupling Covers
Figure 48 - Bearing Shaft Assembly Removal
Refer to Disassembly of Pump With a Type 1 Seal on page 32 and Type 4 Double Seal on page 37 for information on disassembling the pump seal items.
1. Shut off the product flow to the pump and relieve any product pres-sure.
2. Shut off and lock out power to the pump.
3. Disconnect the suction and discharge pipe fittings.
4. Remove the casing clamp and casing (Figure 46, item C). Slide the o-ring off of the backplate
5. Remove the impeller retainer bolt and shaft o-ring (Figure 46, item B).
6. Pull the impeller/backplate assembly off the bearing housing shaft (Figure 46, items D and A).
7. Remove the coupling cover cap screws (Figure 47, item B).
8. Loosen the set screws on the pump coupling (Figure 47, item A).
9. Remove the stand/housing assembly, than remove the end cap (Fig-ure 51, item C on page 42).
10. Push the shaft and bearing assembly out of the housing from the impeller end. (Figure 48).
11. Remove the retaining ring and press the bearings off the shaft (Figure 48, items A and B).
Figure 45 - Install Casing 10/2010 95-03009 Page 41
Maintenance Waukesha Cherry-Burrell
Disassembling the Outer Seal Assemblies1. Using an 1/8" hex wrench, loosen the set screws (Figure 49, item A).
NOTE: The set screws are located opposite the grease fittings in the adapter or end cap.
2. Remove the impeller end of the bearing housing (Figure 49, item B).
3. Remove the outer seal ring assemblies (the inner seal ring and o-rings). See Figure 49 and Figure 50.
Assembling the Outer Seal AssembliesReverse the disassembly procedure (above) with the added step of installing new o-rings in the seal rings.
NOTE: Figure 49 shows the seal position at the motor end. Seals at the pump end face inward. Make sure to tighten the set screws when install-ing the outer seal assemblies (Figure 51).
NOTE: Replace all rubber parts whenever a unit is dismantled for inspec-tion or repair. Lubricate the rubber parts with an approved/sanitary lubri-cant prior to assembly.
Figure 49 - Remove Set Screws
Figure 50 - Seal Configuration
Figure 51 - Outer Seal Assemblies
A. Outer Seal Assembly D. Set Screw
B. Set Screw E. Adapter
C. End Cap F. Stand Page 42 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
Pre-assembled (Cartridge) Seals
Figure 52 - Remove Casing Clamp, Casing and O-ring
Figure 53 - Removal of Wet End
Figure 54 - Remove Seal Assembly.
A. Shims E. Adapter
B. Cap Screw F. Backplate
C. Cartridge Seal G. Impeller
D. Socket Head Screw
Pre-assembled (Cartridge) seals have all of the seal components mounted to a flange, and are pre-adjusted at the factory. Follow the seal manufacturer's (John Crane, A.W. Chesterton, etc.) recommendations regarding application, operation and maintenance.
NOTE: The cartridge seal comes with a set of removable lugs/spacers in place that are used to hold the assembly together until installation is final. Do not remove these lugs until installation is complete and you are instructed to do so in step 17 on page 46.
Disassembly of Pre-assembled (Cartridge) Seals1. Remove all flush connections and fittings.
2. Remove the casing clamp, casing, and o-ring from the housing flange (Figure 52).
3. Remove the impeller retainer bolt and o-ring; then loosen the seal set screws (Figure 53, item A).
4. Pull the impeller, backplate, and seal off the bearing shaft as a unit. Set the assembly face down (on the impeller).
NOTE: The clearance shims that position the impeller within the casing are at the end of the impeller hub (inside the seal.) Keep the shims together as a set for reassembly (Figure 54).
5. Remove the cap screws (Figure 54, item B) holding the cartridge seal to the seal adapter (Figure 54, items C and E).
6. Remove the seal unit from the backplate assembly.
7. Pull the seal from the seal adapter. (Figure 54, items C and E)
8. Remove the seal adapter by removing the socket head cap screws (Figure 54, item D) holding the adapter to the backplate.10/2010 95-03009 Page 43
Maintenance Waukesha Cherry-Burrell
Assembly of a Pump With Pre-assembled (Cartridge) Seals1. Place the shims, backplate and impeller on the shaft assembly.
Hand-tighten the impeller retainer bolt on the shaft.
2. Check the impeller/backplate clearance with the backplate held firmly in position against the motor adapter. Check the space between the back of the impeller and the backplate with a feeler gauge (0.030" nominal) while holding the backplate tight against the bearing housing flange. Any axial movement of the shaft should not be added to the 0.030" nominal clearance (Figure 55). If needed, change this clear-ance by adding or removing shims. Shims (Figure 54, item A) are added on the drive shaft behind the impeller shaft (Figure 54, item G).
3. Confirm the operating clearances by clamping the casing to the bear-ing housing flange and rotating the shaft/impeller manually to be sure the impeller does not touch the casing or backplate.
4. When the proper shim pack is confirmed, remove the casing, impeller and backplate, leaving the shim pack on the shaft.
5. Insert the L-gasket into the backplate (Figure 56, items B and C).
6. Insert the cartridge adapter (Figure 56, item A) into the backplate (Figure 56, item C) and tighten with four socket head cap screws (Fig-ure 56, item D).
7. Install the cartridge seal unit and use the retaining bolts (Figure 57, item B) and flat washers (Figure 57, item A) to secure the unit to the cartridge adapter. Do not tighten the retaining bolts yet.
CAUTION: Be sure the removable lugs/spacers that position the rotating part of the seal in the housing are in place at this time.
8. Apply FDA-approved anti-seize compound to the shaft.
Figure 55 - Clearance Between Impeller and Backplate
Figure 56 - Insert L-gasket, Fasten Adapter in Place
Figure 57 - Fastening Seal Unit in Place Page 44 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
9. (Pedestal Pump only)
Install and position the seal guard (Figure 58).
10. Slide the impeller, backplate and seal unit onto the shaft.
NOTE: Be sure the flushing ports in the cartridge seal are positioned with the inlet toward the bottom and the outlet toward the top (Figure 60, item C).
11. Install the impeller key (Figure 59, item A).
12. Install the o-ring on the impeller retainer bolt (Figure 59, item C).
13. Install the impeller retainer bolt and tighten it (Figure 59, item B).
14. Hold the backplate in place and tighten the cartridge seal into the car-tridge adapter by tightening the cap screws (Figure 60, item E).
. NOTE: The backplate and seal can be rotated to give access to the bolts through the holes in the guard.
15. Install the o-ring and casing; clamp in place (Figure 61).
16. Tighten the two set screws to the shaft (Figure 60, item B).
17. Remove the lugs/spacers (Figure 60, item A).
NOTE: Keep the lugs/spacers to reinstall on the seal cartridge if removal is ever required.
18. Connect the flushing fluid and flood seal.
19. Turn the shaft manually to be sure the shaft rotates without the impel-ler hitting or binding.
Figure 58 - Installing the Guard
Figure 59 - Installing Impeller Assembly
Figure 60 - Typical Cartridge Seal
A. Lugs/Spacers D. Seal Adapter
B. Set Screw (2) E. Cap Screws
C. Flush Pots
Figure 61 - Install O-ring, Casing, Clamp10/2010 95-03009 Page 45
Maintenance Waukesha Cherry-Burrell
Pedestal Base-Mounted Pump Housing Lubrication
Waukesha Series 200 Pedestal Pumps are lubricated with NLGI grade 2 Lithium Complex Grease. Use only NLGI grade 2 Lithium Complex thick-ened greases to replenish the bearing grease supply. The location of the grease fittings is indicated in Figure 62.
NOTE: Combining greases that will not mix with the products above can change the viscosity/consistency of the grease, resulting in bearing dam-age. If there is doubt, remove the bearings, clean, and re-pack them.
For compatible lubricants, contact Waukesha Cherry-Burrell Application Engineering at 1-800-252-5200 or 262-728-1900.
Lubrication Schedule
Size/RPM Hours NOTE: If operating tempera-tures are over 158F (70C), reduce hours by half for every 27F (15C) over the operat-ing temperature.
Small Bore/1750 RPM 4400Small Bore/3500 RPM 2000Large Bore/1750 RPM 2000Large Bore/3500 RPM 1000
Pump AlignmentA flexible coupling is used to compensate for end play and small differ-ences in alignment. The pump and drive shaft should be aligned as closely as possible.
Checking Angular AlignmentUsing feeler gauges or taper gauges, adjust to get equal dimension at all points. At the same time, set space between the coupling halves to the manufacturers recommended distance.
Checking Parallel AlignmentUsing straight edges and shims, move the drive and shim height as needed.
Figure 62 - Grease Fittings on the Pedestal Pump
Figure 63 - Checking Angular Alignment
Figure 64 - Checking Parallel AlignmentPage 46 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
Servicing the Electric Motor
See the motor manufacturers instructions for specific service information.
General Service InformationInspect units at regular intervals.
Keep units clean and ventilation openings clear of dust, dirt or other debris.
CAUTION: Do not over-grease. Excessive lubrication may dam-age the unit.
Lubricate the units per the manufacturers instructions and the instruction plate on the unit.
Motor Lubrication InstructionsSome small motors have sealed-for-life bearings which require no lubrica-tion.
WARNING: Disconnect all power sources to the unit and discharge all parts which may retain an electrical charge before attempting any maintenance or repair. Screens and covers must be maintained in place when the unit is in operation.
Greasable bearings are shipped with a high-quality, wide-temperature-range grease in the bearings.
Some motors can be greased. Refer to the motor manufacturers instruc-tions for more information regarding lubrication procedures and additional service procedures.10/2010 95-03009 Page 47
Maintenance Waukesha Cherry-Burrell
Standard Seal Dimensions
Figure 65 - Installed Seal Length (for aid of assembly) Page 48 95-03009 10/2010
Waukesha Cherry-Burrell Maintenance
Cartridge Seal Dimensions
The following pictorial list of cartridge seals is provided to assist in identifying some of the seals provided with the Model 200 centrifugal pumps. Use of these cartridges requires a cartridge seal adapter.
Figure 66 - Installed Cartridge Seal Length (for aid of assembly)
Figure 67 - Typical Cartridge Seal Installation
A. Socket Head Cap Screw
B. Cartridge Seal Assembly
C. Set Screw (2)
D. Cap Screw
E. Bearing Shaft
F. Clearance Shims 10/2010 95-03009 Page 49
Parts Lists Waukesha Cherry-Burrell
Parts Lists
Type 1 Seal Kits
CT100-172
6
Basic Seal Kit
4 Impeller Retainer O-Ring, FKM 1 1 V70214 V70220 V70220 V70220 V702205 Rotary Seal, Carbon 1 1 9-225A 9-225A 9-225A 9-225A 9-225A6 Seal O-Ring, FKM 1 1 V70224 V70224 V70224 V70224 V702249 Casing O-Ring, FKM 1 1 V70252 V70439 V70446 V70446 V70450
309-241 309-242 309-243 309-243 309-244PL5030-CH13
KIT PART NUMBER
2075ITEM NO.
KIT CONTAINS
DESCRIPTION2085LV
2085 2105QTY.
REQ. PER PUMP
QTY. IN TYPE 1 BASIC
20452065LV
2065 2065HV
Complete Seal Kit
2075
2 Stationary Seal, Purebide 1 1 23-17 23-17 23-17 23-17 23-174 Impeller Retainer O-Ring, FKM 1 1 V70214 V70220 V70220 V70220 V702205 Rotary Seal, Carbon 1 1 9-225A 9-225A 9-225A 9-225A 9-225A6 Seal O-Ring, FKM 1 1 V70224 V70224 V70224 V70224 V702248 L-Gasket, FKM 1 1 9-37 9-37 9-37 9-37 9-379 Casing O-Ring, FKM 1 1 V70252 V70439 V70446 V70446 V70450
309-245 309-246 309-247 309-247 309-248PL5030-CH14
KIT PART NUMBER
DESCRIPTION
KIT CONTAINS2105
QTY. REQ. PER
PUMP
2085LV 2085
2065LV 2065
2065HV2045ITEM
NO.
QTY. IN TYPE 1 BASIC Page 50 95-03009 10/2010
Waukesha Cherry-Burrell Parts Lists
Type 4 Seal Kits
CT100-173
6
Basic Seal Kit
2075
4 Impeller Retainer O-Ring, FKM 1 1 V70214 V70220 V70220 V70220 V702205 Rotary Seal, Carbon 2 2 9-225A 9-225A 9-225A 9-225A 9-225A6 Seal O-Ring, FKM 2 2 V70224 V70224 V70224 V70224 V702249 Casing O-Ring, FKM 1 1 V70252 V70439 V70446 V70446 V70450
12 Seal Housing O-Ring, FKM 2 2 V70039 V70039 V70039 V70039 V70039309-249 309-250 309-251 309-251 309-252
PL5030-CH15
2105KIT CONTAINS
ITEM NO.
KIT PART NUMBER
QTY. REQ. PER
PUMP
QTY. IN TYPE 1 BASIC
DESCRIPTION
2065LV 2065
2065HV
2085LV 20852045
Complete Seal Kit
2075
2 Stationary Seal, Purebide 2 2 23-17 23-17 23-17 23-17 23-174 Impeller Retainer O-Ring, FKM 1 1 V70214 V70220 V70220 V70220 V702205 Rotary Seal, Carbon 2 2 9-225A 9-225A 9-225A 9-225A 9-225A6 Seal O-Ring, FKM 2 2 V70224 V70224 V70224 V70224 V702248 L-Gasket, FKM 2 2 9-37 9-37 9-37 9-37 9-379 Casing O-Ring, FKM 1 1 V70252 V70439 V70446 V70446 V7045012 Seal Housing O-Ring, FKM 2 2 V70039 V70039 V70039 V70039 V70039
309-253 309-254 309-255 309-255 309-256PL5030-CH16
KIT PART NUMBER
KIT CONTAINSITEM NO. DESCRIPTION
2105QTY.
REQ. PER PUMP
QTY. IN TYPE 1 BASIC
20452065LV
2065 2065HV
2085LV 208510/2010 95-03009 Page 51
Parts Lists Waukesha Cherry-Burrell
Type 1 Seal Components and Common Parts
Ct100-167Page 52 95-03009 10/2010
Waukesha Cherry-Burrell Parts Lists
Type 1 Seal Components and Common Parts
1 Deflector 1 69-1* Stationary Seal, Purebide 1 23-17* Stationary Seal, Silicon Carbide 1 23-17A* Stationary Seal, Tungsten Carbide 1 23-17F
3 Stationary Seal Retainer 1 23-784 1/4-20 x 1/2 Bolt 4 30-62
* Rotary Seal, Carbon 1 9-225A* Rotary Seal, Purebide 1 9-225B* Rotary Seal, Silicon Carbide 1 9-225C* Rotary Seal, Tungsten Carbide 1 9-225F
6 1/4-20 x 3/8 Set Screw 2 30-1787 Spring Retainer 1 23-77
* L-Gasket, FKM 1 9-37* L-Gasket, EPDM 1 9-37E* L-Gasket, Silicone 1 9-37R* L-Gasket, FFKM 1 9-37K* L-Gasket, substitute, Teflon 1 20-278 1* Gasket Seal, Gore-Tex (used with 20-278) 1 T80041 1* Seal O-Ring, FKM 1 V70224* Seal O-Ring, EPDM 1 E70224* Seal O-Ring, Silicone 1 S75224* Seal O-Ring, FFKM 1 K75224
10 Washer, tabbed 1 43-8711 Spring 3 24-6518 Block, Water (For type 1 cascade) 1 134-219 8-32 x 1/4 Screw (For type 1 cascade) 1 30-17620 1/4" Plastic Hose (For type 1 cascade) 1 74-121 1/4" Hose Fitting (For type 1 cascade) 1 78-18
Shim, 1" x .005" 143-215JM as req'd 35-1Shim, 1" x .010" 143-215JM as req'd 35-2Shim, 1" x .020" 143-215JM as req'd 35-3Shim, 1-3/8" x .005" 254-326JM as req'd 35-4Shim, 1-3/8" x .010" 254-326JM as req'd 35-5Shim, 1-3/8" x .020" 254-326JM as req'd 35-6
PL5030-CH11NOTES:* Recommended Spare Parts1. T80041 must be used in conjunction with 20-278 if 20-278 is selected.
NOTESITEM NO.
DESCRIPTIONQTY. PER
PUMP
PART NO.
22
2
5
8
910/2010 95-03009 Page 53
Parts Lists Waukesha Cherry-Burrell
Type 4 Seal Components and Common Parts
CT100-064b
16 22 82
5
910
6, 7 1110
95
28
1217
13
121415Page 54 95-03009 10/2010
Waukesha Cherry-Burrell Parts Lists
Type 4 Seal Components and Common Parts
* Stationary Seal, Purebide 2 23-17* Stationary Seal, Silicon Carbide 2 23-17A* Stationary Seal, Tungsten Carbide 2 23-17F* Rotary Seal, Carbon 2 9-225A* Rotary Seal, Purebide 2 9-225B* Rotary Seal, Silicon Carbide 2 9-225C* Rotary Seal, Tungsten Carbide 2 9-225F
6 1/4-20 x 3/8 Set Screw 2 30-1787 Spring Retainer 1 23-77
* L-Gasket, FKM 2 9-37* L-Gasket, EPDM 2 9-37E* L-Gasket, Silicone 2 9-37R* L-Gasket, FFKM 2 9-37K* 2 20-278 1* Gasket Seal, Gore-Tex (used with 20-278) 2 T80041 1* Seal O-Ring, FKM 2 V70224* Seal O-Ring, EPDM 2 E70224* Seal O-Ring, Silicone 2 S75224* Seal O-Ring, FFKM 2 K75224
10 Washer, tabbed 2 43-8711 Spring 6 24-65
* 12 O-Ring, Housing, FKM 2 V7003913 Housing, Seal 1 23-8014 Retainer, Seal 1 23-7915 1/4-20 x 3 Cap Screw 4 30-175
Slinger, 143-215JM 1 69-4Deflector, 254-326JM 1 69-1
17 1/4" NPT Plug 2 78-155Shim, 1" x .005" 143-215JM as req'd 35-1Shim, 1" x .010" 143-215JM as req'd 35-2Shim, 1" x .020" 143-215JM as req'd 35-3Shim, 1-3/8" x .005" 254-326JM as req'd 35-4Shim, 1-3/8" x .010" 254-326JM as req'd 35-5Shim, 1-3/8" x .020" 254-326JM as req'd 35-6
PL5030-CH12NOTES:* Recommended Spare Parts1. T80041 must be used in conjunction with 20-278 if 20-278 is selected.
NOTESITEM NO.
DESCRIPTIONQTY. PER
PUMP
PART NO.
L-Gasket, substitute, Teflon
16
22
2
5
8
910/2010 95-03009 Page 55
Parts Lists Waukesha Cherry-Burrell
2045 Pump Parts
CT100-113a
Seals
12
8 7
5
109
2 4
111
3
2045 Casing Parts
1-1/2 x 1-1/2 2 x 1-1/2S-Line (MP) CENTPT00549 CENTPT00550Bevel Seat CENTPT00551 CENTPT00552I-Line; Female CENTPT00553 CENTPT00554I-Line; Male CENTPT00555 CENTPT00556Q-Line CENTPT00557 CENTPT00558Weld CENTPT00559 CENTPT00560NPT; Male CENTPT00561 CENTPT00562 1NPT; Female CENTPT00563 CENTPT00564 1150 LB. Flange CENTPT00565 CENTPT00566 1
PL5030-CH2NOTES:1. These casings do not meet the requirements of 3A Sanitary Standards.
FITTING TYPE NOTESSANITARYPage 56 95-03009 10/2010
Waukesha Cherry-Burrell Parts Lists1 Casing (see 2045 Casing Parts List) 12 Impeller, Full 4.5" Diameter 1 5-80X 13 Impeller Retainer 1 129-773X
* Impeller O-Ring, FKM 1 V70214* Impeller O-Ring, EPDM 1 E70214* Impeller O-Ring, Silicone 1 S75214* Impeller O-Ring, FFKM 1 K75214* Impeller O-Ring, PTFE ENCAP. 1 T80214
5 Adapter, 143JM - 184JM Frame, SS 1 122059+ 27 3/8 - 16 x 3/4" Hex Screw 4 30-508 3/8" Lockwasher 4 43-28
* Casing O-Ring, FKM 1 V70252* Casing O-Ring, EPDM 1 E70252* Casing O-Ring, Silicone 1 S75252* Casing O-Ring, FFKM 1 K75252* Casing O-Ring, PTFE ENCAP. 1 T80252
10 Backplate 1 1-59X11 Casing Clamp 1 119-7112 Key - 3/16" 1 65-3
PL5030-CH1NOTES:*
1.
2. Previously supplied as 2 pieces, an adapter and a seal guard; now a single piece.
Trimmed impellers use the same part number and price; specify the diameter required in 1/8" increments on order.
NOTES
4
9
ITEM NO. DESCRIPTION
QTY. PER
PUMP
PART NO.
Recommended Spare Parts - available as kits for standard seals-see seal kit pages.
2045 Pump Parts10/2010 95-03009 Page 57
Parts Lists Waukesha Cherry-Burrell
2065LV - 2065 - 2065HV Pump Parts
CT100-113a
Seals
12
8 7
5
109
2 4
111
3
2065LV - 2065 - 2065HV Casing Parts
2065 SANITARY 2065HV SANITARY1-1/2 x 1-1/2 2 x 1-1/2 2-1/2 x 1-1/2 2-1/2 X 2 3 X 2
S-Line (MP) CENTPT00569 CENTPT00455 CENTPT00413 CENTPT00417 CENTPT00570Bevel Seat CENTPT00571 CENTPT00572 CENTPT00573 CENTPT00574 CENTPT00575I-Line; Female CENTPT00576 CENTPT00577 CENTPT00578 CENTPT00579 CENTPT00580I-Line; Male CENTPT00581 CENTPT00582 CENTPT00583 CENTPT00584 CENTPT00585Q-Line CENTPT00586 CENTPT00587 CENTPT00588 CENTPT00589 CENTPT00590Weld CENTPT00591 CENTPT00592 CENTPT00593 CENTPT00594 CENTPT00595NPT; Male CENTPT00596 CENTPT00597 CENTPT00598 CENTPT00599 CENTPT00600 1NPT; Female CENTPT00601 CENTPT00602 CENTPT00603 CENTPT00604 CENTPT00605 1150 LB. Flange CENTPT00606 CENTPT00607 CENTPT00608 CENTPT00609 CENTPT00280 1
PL5030-CH4NOTES:1. These casings do not meet the requirements of 3A Sanitary Standards.
NOTESFITTING TYPE 2065LV SANITARYPage 58 95-03009 10/2010
Waukesha Cherry-Burrell Parts Lists
2065LV - 2065 - 2065HV Pump Parts
1 Casing (see 2065LV-2065-2065HV Casing Parts List) 12065LV Impeller, 6.5" Dia., 143-215JM, SM Bore 1 109256+ 12065LV Impeller, 6.5" Dia., 254-326JM, LG Bore 1 109258+ 12065 Impeller, 6.5" Dia., 143-215JM, SM Bore 1 109260+ 12065 Impeller, 6.5" Dia., 254-326JM, LG Bore 1 109262+ 12065HV Impeller, 6.5" Dia., 143-215JM, SM Bore 1 109264+ 12065HV Impeller, 6.5" Dia., 254-326JM, LG Bore 1 109266+ 1Impeller Retainer, 143-215JM SM Bore 1 129-771XImpeller Retainer, 254-326JM LG Bore 1 129-772X
* Impeller O-Ring, FKM 1 V70220* Impeller O-Ring, EPDM 1 E70220* Impeller O-Ring, Silicone 1 S75220* Impeller O-Ring, FFKM 1 K75220* Impeller O-Ring, PTFE ENCAPSULATED 1 T80220
Adapter, 143-184JM Frame, SS 1 122045+ 2Adapter, 213-215JM Frame, SS 1 122035+ 2Adapter, 254-256JM Frame, SS 1 121888+ 2Adapter, 284-326JM Frame, SS 1 122069+ 23/8-16 x 1" Hex Screw, 143-184JM Frame 4 30-301/2-13 x 1-1/4" Hex Screw, 213-256JM Frame 4 30-36X5/8-11 x 1-1/2" Hex Screw, 284-326JM Frame 4 30-1053/8" Lockwasher 4 43-281/2" Lockwasher 4 43-165/8" Lockwasher 4 43-33
* Casing O-Ring, FKM 1 V70439* Casing O-Ring, EPDM 1 E70439* Casing O-Ring, Silicone 1 S75439* Casing O-Ring, FFKM 1 K75439* Casing O-Ring, PTFE ENCAPSULATED 1 T80439
10 Backplate 1 1-60X11 Casing Clamp 1 119-70
Key-3/16",