INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 1
WIRELESS WEARABLE ORTHOPEDIC DEVICE FOR POSTURE
MONITORING DURING FRACTURE HEALING PERIOD
BSDhanya1 SRamya2 VS Jagadhish3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mail ramyasekar687gmailcom
Abstractminus
The observance of any human physiological parameters throughout rehabilitation
exercises needs noninvasive sensors for the patient This paper describes a wireless wearable
Criss-cross flex array sensors for posture monitoring during rehabilitation or reinforcement
exercises The subject posture is measured through a sensorized Criss-cross flex array sensors
using an inductive sensor sewn directly on the fabric The wireless wearable Criss-cross flex
array sensors design specifications are the following independence from the remote unit easy
to use lightweight and comfort of wearing This paper reports the abstract framework the
invented device description and also the adopted experimental setup
Keywordsminus Parameters Rehabilitation Noninvasive sensors Wearable criss-cross sensors
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 2
A PROACTIVE SYSTEM TO PREVENT PRESSURE ULCERS
ACQUIRED VIA PROLONGED HOSPITALIZATION WIRELESS
ALDharini1 MHarshavarthini2 12 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mail dharinicbe98gmailcom
Abstractminus
Pressure ulcers are a serious problem affecting over a million patients every year
These ulcers often occur when patients have limited mobility and cannot change positions in
bed on their own Eventhough there are accepted guidelines for attending and repositioning
high-risk patients the rate of pressure ulcers continues to rise This paper presents a wearable
wireless vital sign monitor capable of continuously measuring the duration and orientation of a
patientrsquos posture throughout Patient posture is determined using a tri-axial accelerometer
attached to a patientrsquos torso A set of algorithms are used to process the accelerometer signals
to adaptively identify accelerometer alignment on the patient and classify patient orientation
and enables alerts to be sent to the caregiver when a patient turn is due in accordance with the
protocol adopted by the hospital A novel method to address the need for improved pressure
ulcer prevention is presented The patientrsquos position is continuously monitored and the turning
procedure carried out is logged and updated on the hospitalrsquos cloud system thereby enabling
centralized monitoring Under a controlled setting system was able to continuously monitor
patientrsquos position and can accurately detect standard patient positions
Keywordsminus pressure ulcers repositioning wearable tri axial accelerometer cloud system
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 3
WILDLIFE COLLISION AVOIDER
SSneha Prabha1 SKaran Kumar2 AVishnu3 1 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 2 UG Scholar Department of Mechatronics
SNS College of Technology Coimbatore India 3Assistant Professor Department of Mechatronics
SNS College of Technology Coimbatore India
E Mail snehasoundravelgmailcom
Abstractminus
One of the main problems facing all developed countries is death and injuries from
road accidents When an animal accident occurs on the road the main problem is a traffic
accident This article provides a simple and inexpensive way to automatically detect animals on
motorways to prevent collisions with vehicles using computer vision technology There is also
a method for determining the distance between the vehicle mounted on the vehicle and the
actual device Using the proposed system more than 2200 positive and negative images were
recorded and tested at different vehicle speeds After a 2 second rule the proposed method can
warn the driver when the vehicle speed is 35 km h and the animal is recognized correctly The
overall accuracy of the proposed method is almost 825
Keywordsminus wildlife accident vehicle speed detection images
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 4
REACTIVE POWER IMPROVEMENT USING ADAPTIVE
CURRENT CONTROLLER METHOD
KSenrayan1 DrPSivaraman2
1 Research Scholar Department of Electrical and Electronics Engineering Bannari Amman Institute of Technology Erode India
2Assistant Professor Department of Biomedical Engineering Bannari Amman Institute of Technology Erode India
E Mail ksenrayangmailcom
Abstractminus
Most of the pollution issues created in power systems are due to the non-linear
characteristics and fast switching of power electronic equipment Power quality issues are
becoming stronger because sensitive equipment will be more sensitive for market competition
reasons equipment will continue polluting the system more and more due to cost increase
caused by the built-in compensation and sometimes for the lack of enforced regulations
Efficiency and cost are considered today almost at the same level In this paper the three-phase
grid connected inverter has been investigated The inverterrsquos control strategy is based on the
adaptive hysteresis current controller Inverter connects the DG (distributed generation) source
to the grid The main advantages of this method are constant switching frequency better
current control easy filter design and less THD (total harmonic distortion) Since a constant
and ripple free dc bus voltage is not ensured at the output of alternate energy sources the main
aim of the proposed algorithm is to make the output of the inverter immune to the fluctuations
in the dc input voltage This inverter can be used to connect the medium and small-scale wind
turbines and solar cells to the grid and compensate local load reactive power Reactive power
compensating improves SUF (system usage factor) The simulation results confirm that
switching frequency is constant and THD of injected current is low
Keywordsminus Adaptive hysteresis current controller distributed generation system grid connected inverter system usage factor total harmonic distortion
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 5
ARDUINO BASED SMART IRRIGATION SYSTEM USING GSM
VChandan Kumar1 VAvinash Reddy2 SRamkishore3 1 2 3 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail vchandankumar2gmail
Abstractminus
Irrigation is a scientific process of supplying water to the soil that is to be cultivated
Generally in dry regions having little rainfall water had to be supplied to the fields either
through canals or hand pumps tube wells Conventional irrigation methods have problems such
as increase in workload of farm labor and it cause a problems such as over-irrigation or under-
irrigation and leaching of soil India is the country of agriculture Agricultural sector is very
important as far as Indian villagerrsquos point of view Productivity of agriculture fieldrsquos do not
depend on excess of water sprinkled to the field but depends on better matching of water
supply with crop and uniform environmental conditions that are suitable for farming To
measure the crop water demand it is essential to estimate the soil humidity Under irrigation or
over-irrigation system leads to excessive or less water supply which may cause worse results
such as yield reduction
Keywordsminus Irrigation agriculture productivity
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 6
VEHICLE ACCIDENT DETECTION WITH GSM MODULE
Pavan Kumar Galam1 SMurugesan2 Somasekhar Reddy3 PMurugan4 1 2 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
3Assistant Professor Department of Electronics and Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail pavan99424gmailcom
Abstractminus
This paper presents a modified design of Vehicle Accident Detection with GSM
Module In highly populated Countries everyday people lose their lives because of accidents
and poor emergency facilities We Can save the lives when the correct time of ambulance is
provided This project implies a system which is a solution to this drawback when a vehicle
meets with an accident immediately a Vibration sensor will detect the signal and sends it to the
Arduino microcontroller Microcontroller will send an alert message through the GSM modem
by that we can confirm that accident is happen to our relatives or a person The proposed
systems have been simulated and practically design by the use of hardware components and the
results are satisfied with the expectation
Keywordsminus Vehicle Accident Arduino Uno GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 2
A PROACTIVE SYSTEM TO PREVENT PRESSURE ULCERS
ACQUIRED VIA PROLONGED HOSPITALIZATION WIRELESS
ALDharini1 MHarshavarthini2 12 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mail dharinicbe98gmailcom
Abstractminus
Pressure ulcers are a serious problem affecting over a million patients every year
These ulcers often occur when patients have limited mobility and cannot change positions in
bed on their own Eventhough there are accepted guidelines for attending and repositioning
high-risk patients the rate of pressure ulcers continues to rise This paper presents a wearable
wireless vital sign monitor capable of continuously measuring the duration and orientation of a
patientrsquos posture throughout Patient posture is determined using a tri-axial accelerometer
attached to a patientrsquos torso A set of algorithms are used to process the accelerometer signals
to adaptively identify accelerometer alignment on the patient and classify patient orientation
and enables alerts to be sent to the caregiver when a patient turn is due in accordance with the
protocol adopted by the hospital A novel method to address the need for improved pressure
ulcer prevention is presented The patientrsquos position is continuously monitored and the turning
procedure carried out is logged and updated on the hospitalrsquos cloud system thereby enabling
centralized monitoring Under a controlled setting system was able to continuously monitor
patientrsquos position and can accurately detect standard patient positions
Keywordsminus pressure ulcers repositioning wearable tri axial accelerometer cloud system
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 3
WILDLIFE COLLISION AVOIDER
SSneha Prabha1 SKaran Kumar2 AVishnu3 1 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 2 UG Scholar Department of Mechatronics
SNS College of Technology Coimbatore India 3Assistant Professor Department of Mechatronics
SNS College of Technology Coimbatore India
E Mail snehasoundravelgmailcom
Abstractminus
One of the main problems facing all developed countries is death and injuries from
road accidents When an animal accident occurs on the road the main problem is a traffic
accident This article provides a simple and inexpensive way to automatically detect animals on
motorways to prevent collisions with vehicles using computer vision technology There is also
a method for determining the distance between the vehicle mounted on the vehicle and the
actual device Using the proposed system more than 2200 positive and negative images were
recorded and tested at different vehicle speeds After a 2 second rule the proposed method can
warn the driver when the vehicle speed is 35 km h and the animal is recognized correctly The
overall accuracy of the proposed method is almost 825
Keywordsminus wildlife accident vehicle speed detection images
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 4
REACTIVE POWER IMPROVEMENT USING ADAPTIVE
CURRENT CONTROLLER METHOD
KSenrayan1 DrPSivaraman2
1 Research Scholar Department of Electrical and Electronics Engineering Bannari Amman Institute of Technology Erode India
2Assistant Professor Department of Biomedical Engineering Bannari Amman Institute of Technology Erode India
E Mail ksenrayangmailcom
Abstractminus
Most of the pollution issues created in power systems are due to the non-linear
characteristics and fast switching of power electronic equipment Power quality issues are
becoming stronger because sensitive equipment will be more sensitive for market competition
reasons equipment will continue polluting the system more and more due to cost increase
caused by the built-in compensation and sometimes for the lack of enforced regulations
Efficiency and cost are considered today almost at the same level In this paper the three-phase
grid connected inverter has been investigated The inverterrsquos control strategy is based on the
adaptive hysteresis current controller Inverter connects the DG (distributed generation) source
to the grid The main advantages of this method are constant switching frequency better
current control easy filter design and less THD (total harmonic distortion) Since a constant
and ripple free dc bus voltage is not ensured at the output of alternate energy sources the main
aim of the proposed algorithm is to make the output of the inverter immune to the fluctuations
in the dc input voltage This inverter can be used to connect the medium and small-scale wind
turbines and solar cells to the grid and compensate local load reactive power Reactive power
compensating improves SUF (system usage factor) The simulation results confirm that
switching frequency is constant and THD of injected current is low
Keywordsminus Adaptive hysteresis current controller distributed generation system grid connected inverter system usage factor total harmonic distortion
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 5
ARDUINO BASED SMART IRRIGATION SYSTEM USING GSM
VChandan Kumar1 VAvinash Reddy2 SRamkishore3 1 2 3 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail vchandankumar2gmail
Abstractminus
Irrigation is a scientific process of supplying water to the soil that is to be cultivated
Generally in dry regions having little rainfall water had to be supplied to the fields either
through canals or hand pumps tube wells Conventional irrigation methods have problems such
as increase in workload of farm labor and it cause a problems such as over-irrigation or under-
irrigation and leaching of soil India is the country of agriculture Agricultural sector is very
important as far as Indian villagerrsquos point of view Productivity of agriculture fieldrsquos do not
depend on excess of water sprinkled to the field but depends on better matching of water
supply with crop and uniform environmental conditions that are suitable for farming To
measure the crop water demand it is essential to estimate the soil humidity Under irrigation or
over-irrigation system leads to excessive or less water supply which may cause worse results
such as yield reduction
Keywordsminus Irrigation agriculture productivity
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 6
VEHICLE ACCIDENT DETECTION WITH GSM MODULE
Pavan Kumar Galam1 SMurugesan2 Somasekhar Reddy3 PMurugan4 1 2 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
3Assistant Professor Department of Electronics and Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail pavan99424gmailcom
Abstractminus
This paper presents a modified design of Vehicle Accident Detection with GSM
Module In highly populated Countries everyday people lose their lives because of accidents
and poor emergency facilities We Can save the lives when the correct time of ambulance is
provided This project implies a system which is a solution to this drawback when a vehicle
meets with an accident immediately a Vibration sensor will detect the signal and sends it to the
Arduino microcontroller Microcontroller will send an alert message through the GSM modem
by that we can confirm that accident is happen to our relatives or a person The proposed
systems have been simulated and practically design by the use of hardware components and the
results are satisfied with the expectation
Keywordsminus Vehicle Accident Arduino Uno GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 3
WILDLIFE COLLISION AVOIDER
SSneha Prabha1 SKaran Kumar2 AVishnu3 1 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 2 UG Scholar Department of Mechatronics
SNS College of Technology Coimbatore India 3Assistant Professor Department of Mechatronics
SNS College of Technology Coimbatore India
E Mail snehasoundravelgmailcom
Abstractminus
One of the main problems facing all developed countries is death and injuries from
road accidents When an animal accident occurs on the road the main problem is a traffic
accident This article provides a simple and inexpensive way to automatically detect animals on
motorways to prevent collisions with vehicles using computer vision technology There is also
a method for determining the distance between the vehicle mounted on the vehicle and the
actual device Using the proposed system more than 2200 positive and negative images were
recorded and tested at different vehicle speeds After a 2 second rule the proposed method can
warn the driver when the vehicle speed is 35 km h and the animal is recognized correctly The
overall accuracy of the proposed method is almost 825
Keywordsminus wildlife accident vehicle speed detection images
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 4
REACTIVE POWER IMPROVEMENT USING ADAPTIVE
CURRENT CONTROLLER METHOD
KSenrayan1 DrPSivaraman2
1 Research Scholar Department of Electrical and Electronics Engineering Bannari Amman Institute of Technology Erode India
2Assistant Professor Department of Biomedical Engineering Bannari Amman Institute of Technology Erode India
E Mail ksenrayangmailcom
Abstractminus
Most of the pollution issues created in power systems are due to the non-linear
characteristics and fast switching of power electronic equipment Power quality issues are
becoming stronger because sensitive equipment will be more sensitive for market competition
reasons equipment will continue polluting the system more and more due to cost increase
caused by the built-in compensation and sometimes for the lack of enforced regulations
Efficiency and cost are considered today almost at the same level In this paper the three-phase
grid connected inverter has been investigated The inverterrsquos control strategy is based on the
adaptive hysteresis current controller Inverter connects the DG (distributed generation) source
to the grid The main advantages of this method are constant switching frequency better
current control easy filter design and less THD (total harmonic distortion) Since a constant
and ripple free dc bus voltage is not ensured at the output of alternate energy sources the main
aim of the proposed algorithm is to make the output of the inverter immune to the fluctuations
in the dc input voltage This inverter can be used to connect the medium and small-scale wind
turbines and solar cells to the grid and compensate local load reactive power Reactive power
compensating improves SUF (system usage factor) The simulation results confirm that
switching frequency is constant and THD of injected current is low
Keywordsminus Adaptive hysteresis current controller distributed generation system grid connected inverter system usage factor total harmonic distortion
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 5
ARDUINO BASED SMART IRRIGATION SYSTEM USING GSM
VChandan Kumar1 VAvinash Reddy2 SRamkishore3 1 2 3 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail vchandankumar2gmail
Abstractminus
Irrigation is a scientific process of supplying water to the soil that is to be cultivated
Generally in dry regions having little rainfall water had to be supplied to the fields either
through canals or hand pumps tube wells Conventional irrigation methods have problems such
as increase in workload of farm labor and it cause a problems such as over-irrigation or under-
irrigation and leaching of soil India is the country of agriculture Agricultural sector is very
important as far as Indian villagerrsquos point of view Productivity of agriculture fieldrsquos do not
depend on excess of water sprinkled to the field but depends on better matching of water
supply with crop and uniform environmental conditions that are suitable for farming To
measure the crop water demand it is essential to estimate the soil humidity Under irrigation or
over-irrigation system leads to excessive or less water supply which may cause worse results
such as yield reduction
Keywordsminus Irrigation agriculture productivity
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 6
VEHICLE ACCIDENT DETECTION WITH GSM MODULE
Pavan Kumar Galam1 SMurugesan2 Somasekhar Reddy3 PMurugan4 1 2 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
3Assistant Professor Department of Electronics and Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail pavan99424gmailcom
Abstractminus
This paper presents a modified design of Vehicle Accident Detection with GSM
Module In highly populated Countries everyday people lose their lives because of accidents
and poor emergency facilities We Can save the lives when the correct time of ambulance is
provided This project implies a system which is a solution to this drawback when a vehicle
meets with an accident immediately a Vibration sensor will detect the signal and sends it to the
Arduino microcontroller Microcontroller will send an alert message through the GSM modem
by that we can confirm that accident is happen to our relatives or a person The proposed
systems have been simulated and practically design by the use of hardware components and the
results are satisfied with the expectation
Keywordsminus Vehicle Accident Arduino Uno GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 4
REACTIVE POWER IMPROVEMENT USING ADAPTIVE
CURRENT CONTROLLER METHOD
KSenrayan1 DrPSivaraman2
1 Research Scholar Department of Electrical and Electronics Engineering Bannari Amman Institute of Technology Erode India
2Assistant Professor Department of Biomedical Engineering Bannari Amman Institute of Technology Erode India
E Mail ksenrayangmailcom
Abstractminus
Most of the pollution issues created in power systems are due to the non-linear
characteristics and fast switching of power electronic equipment Power quality issues are
becoming stronger because sensitive equipment will be more sensitive for market competition
reasons equipment will continue polluting the system more and more due to cost increase
caused by the built-in compensation and sometimes for the lack of enforced regulations
Efficiency and cost are considered today almost at the same level In this paper the three-phase
grid connected inverter has been investigated The inverterrsquos control strategy is based on the
adaptive hysteresis current controller Inverter connects the DG (distributed generation) source
to the grid The main advantages of this method are constant switching frequency better
current control easy filter design and less THD (total harmonic distortion) Since a constant
and ripple free dc bus voltage is not ensured at the output of alternate energy sources the main
aim of the proposed algorithm is to make the output of the inverter immune to the fluctuations
in the dc input voltage This inverter can be used to connect the medium and small-scale wind
turbines and solar cells to the grid and compensate local load reactive power Reactive power
compensating improves SUF (system usage factor) The simulation results confirm that
switching frequency is constant and THD of injected current is low
Keywordsminus Adaptive hysteresis current controller distributed generation system grid connected inverter system usage factor total harmonic distortion
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 5
ARDUINO BASED SMART IRRIGATION SYSTEM USING GSM
VChandan Kumar1 VAvinash Reddy2 SRamkishore3 1 2 3 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail vchandankumar2gmail
Abstractminus
Irrigation is a scientific process of supplying water to the soil that is to be cultivated
Generally in dry regions having little rainfall water had to be supplied to the fields either
through canals or hand pumps tube wells Conventional irrigation methods have problems such
as increase in workload of farm labor and it cause a problems such as over-irrigation or under-
irrigation and leaching of soil India is the country of agriculture Agricultural sector is very
important as far as Indian villagerrsquos point of view Productivity of agriculture fieldrsquos do not
depend on excess of water sprinkled to the field but depends on better matching of water
supply with crop and uniform environmental conditions that are suitable for farming To
measure the crop water demand it is essential to estimate the soil humidity Under irrigation or
over-irrigation system leads to excessive or less water supply which may cause worse results
such as yield reduction
Keywordsminus Irrigation agriculture productivity
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 6
VEHICLE ACCIDENT DETECTION WITH GSM MODULE
Pavan Kumar Galam1 SMurugesan2 Somasekhar Reddy3 PMurugan4 1 2 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
3Assistant Professor Department of Electronics and Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail pavan99424gmailcom
Abstractminus
This paper presents a modified design of Vehicle Accident Detection with GSM
Module In highly populated Countries everyday people lose their lives because of accidents
and poor emergency facilities We Can save the lives when the correct time of ambulance is
provided This project implies a system which is a solution to this drawback when a vehicle
meets with an accident immediately a Vibration sensor will detect the signal and sends it to the
Arduino microcontroller Microcontroller will send an alert message through the GSM modem
by that we can confirm that accident is happen to our relatives or a person The proposed
systems have been simulated and practically design by the use of hardware components and the
results are satisfied with the expectation
Keywordsminus Vehicle Accident Arduino Uno GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 5
ARDUINO BASED SMART IRRIGATION SYSTEM USING GSM
VChandan Kumar1 VAvinash Reddy2 SRamkishore3 1 2 3 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail vchandankumar2gmail
Abstractminus
Irrigation is a scientific process of supplying water to the soil that is to be cultivated
Generally in dry regions having little rainfall water had to be supplied to the fields either
through canals or hand pumps tube wells Conventional irrigation methods have problems such
as increase in workload of farm labor and it cause a problems such as over-irrigation or under-
irrigation and leaching of soil India is the country of agriculture Agricultural sector is very
important as far as Indian villagerrsquos point of view Productivity of agriculture fieldrsquos do not
depend on excess of water sprinkled to the field but depends on better matching of water
supply with crop and uniform environmental conditions that are suitable for farming To
measure the crop water demand it is essential to estimate the soil humidity Under irrigation or
over-irrigation system leads to excessive or less water supply which may cause worse results
such as yield reduction
Keywordsminus Irrigation agriculture productivity
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 6
VEHICLE ACCIDENT DETECTION WITH GSM MODULE
Pavan Kumar Galam1 SMurugesan2 Somasekhar Reddy3 PMurugan4 1 2 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
3Assistant Professor Department of Electronics and Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail pavan99424gmailcom
Abstractminus
This paper presents a modified design of Vehicle Accident Detection with GSM
Module In highly populated Countries everyday people lose their lives because of accidents
and poor emergency facilities We Can save the lives when the correct time of ambulance is
provided This project implies a system which is a solution to this drawback when a vehicle
meets with an accident immediately a Vibration sensor will detect the signal and sends it to the
Arduino microcontroller Microcontroller will send an alert message through the GSM modem
by that we can confirm that accident is happen to our relatives or a person The proposed
systems have been simulated and practically design by the use of hardware components and the
results are satisfied with the expectation
Keywordsminus Vehicle Accident Arduino Uno GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 6
VEHICLE ACCIDENT DETECTION WITH GSM MODULE
Pavan Kumar Galam1 SMurugesan2 Somasekhar Reddy3 PMurugan4 1 2 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
3Assistant Professor Department of Electronics and Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail pavan99424gmailcom
Abstractminus
This paper presents a modified design of Vehicle Accident Detection with GSM
Module In highly populated Countries everyday people lose their lives because of accidents
and poor emergency facilities We Can save the lives when the correct time of ambulance is
provided This project implies a system which is a solution to this drawback when a vehicle
meets with an accident immediately a Vibration sensor will detect the signal and sends it to the
Arduino microcontroller Microcontroller will send an alert message through the GSM modem
by that we can confirm that accident is happen to our relatives or a person The proposed
systems have been simulated and practically design by the use of hardware components and the
results are satisfied with the expectation
Keywordsminus Vehicle Accident Arduino Uno GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 7
SMART SWITCH FOR FARMING
VSailesh1 SBhanutejaswi2 MPoornasree3 KJeyaprakash4 123 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail saileshv1108gmailcom
Abstractminus
Bluetooth technology has brought revolution to each and every field of common manrsquos
life by making everything smart and intelligent BLUETOOTH refers to a network of things
which make a self-configuring network The development of Intelligent Smart Farming
Bluetooth based devices is day by day turning the face of agriculture production by not only
enhancing it but also making it cost-effective and reducing wastage The aim objective of this
paper is to propose a Novel Smart BLUETOOTH based Agriculture Stick assisting farmers in
getting Live Data (Temperature Soil Moisture) for efficient environment monitoring which
will enable them to do smart farming and increase their overall yield and quality of products
The Agriculture stick being proposed via this paper is integrated with Arduino Technology
Breadboard mixed with various sensors and live data feed can be obtained online from Things
speak com The product being proposed is tested on Live Agriculture Fields giving high
accuracy over 98 in data feeds
Keywordsminus self-configuring network agriculture broadband
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 8
AUTOMATIC SHUTTLE MOVEMENT DETECTION USING
TEXTILE INDUSTRY
KSathish1 12 UG Scholar Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mail smartsathish898gmailcom
Abstractminus
The investment in an automated yarn defect detection system is more than economical
when reduction in labor cost and associated benefits are considered The inspection of real yarn
defects is particularly challenging due to the large number of yarn defect classes which are
characterized by their vagueness and ambiguity Categorization of fabric defect detection
techniques is useful in evaluating the qualities of identified features In this project a novel
defect detection scheme based on yarn moving detection is proposed to tackle the problem of
automated defect detection for woven fabrics n the proposed scheme important texture
features of the textile yarn detection are extracted using a pre-trained yarn network The test
results obtained exhibit accurate defect detection with low false alarms thus showing the
effectiveness and robustness of the proposed detection scheme In addition the proposed
detection scheme is further evaluated in real time by using a prototyped automated inspection
system
Keywordsminus yarn defect-detection
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 9
ENSURING ROAD SAFETY AND BETTER ENVIRONMENT BY
DESIGN AND IMPLEMENTATION OF AN EMBEDDED SYSTEM
PMurugan1 JJeya Surya2 GRagadharshini3 1Associate Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail jeyasuryajaisankar11gmailcom
Abstractminus
The project work focuses on prevention of damage of roads and prevents vehicle
damage Now-a-days roads play a very important role in every part of world The problem of
overload in the vehicle transport has emerged Therefore how simply and conveniently to
know the vehicle load and how to effectively limit overload has become a key issue The value
lies in providing safe and convenient travel for the users As the device is working in the
loading process it can ensure to prevent vehicle overloading in the process of driving the
drivers donrsquot have to worry about being fined due to overload syndrome ensure the personal
safety of driving At the same time the system is designed to save the national highway
maintenance fees and to ensure peoplersquos lives and property The main aim of the project is to
identify the effectiveness of using overload system in enhancing the operations in enforcing
vehicle weight limit regulations
Keywordsminus arduino board zigbee GSM
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 10
SMART CROP PROTECTION SYSTEM Hari Obul Sunki Reddy1
1 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education
Krishnankovil India
E Mail sunkireddyhgmailcom
Abstractminus
Crops in farms are many times sweep away by local animals like buffaloes cows
goats birds etc This leads to huge losses for the farmers It is not possible for farmers to road
block entire field or stop over on field 24 hours and guard it So here we come up with
automatic crop protection system from animals This is a microcontroller stationed system
using PIC microcontroller This system uses a motion sensor to detect wild animals moving
closer near the field In such a case the PIR sensor sense it and sends a signal to the
microcontroller to act The microcontroller will activate the buzzer which sounds an alarm to
woo the animals away from the field as well as sends SMS to the farmer so that he may know
about the situation and come to the field in case the animals donrsquot turn away by the alarm This
ensures complete safety of crops from animals thus protecting the farmerrsquos loss
Keywordsminusautomatic crop-protection motion sensor
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 11
DIGITAL MEDI KIT
VMadhubala1 AKuratpannan2 1 2 UG Scholar Department of Electronics and Communication Engineering
PSNA College of Engineering and Technology Dindigul India
E Mailpannankuratgmailcom
Abstractminus
The digital medi kit aims to provide preliminary support for people facing the most
common types Our aim is to combine atmost necessary medical checkup in a single system
The four process are checking heart rate and oxygen content in blood blood pressurepulse
rate insulin level and body temperature This system will be integrated to ArduinoMAX30100
is used to detect heart beat and oxygen content in blood of a person It measures the change in
volume of blood through an organ of body which causes a change in light intensity The
MAX30100 is an integrated pulse oximetry and heart-rate monitor sensor It combines two
LEDs a photodetector optimized optics and low-noise analog signal processing to detect pulse
oximetry and heart-rate signals The MAX30100 is a complete pulse oximetry and heart-rate
sensor system solution The flow of blood volume is decided by the rate of heart pulses and
since light is absorbed by blood then signal pulses are equivalent to heart beat pulses and the
output is given to the LCD display The insulin level of a person is detected by Continuous
Glucose Monitoring (CGM)sensorCGM sensor provies real time glucose readings allowing
people with diabetes to know their glucose levelsThe sensor is inserted under the skin with an
applicator the transmitter is small light weight piece that fits onto the sensor The transmitter
wirelessly senses the glucose data from sensor to monitor The receiver is a slim portable that
is fitted to the arduino and displays the glucose information sent from transmitter It is inserted
on your belly or arm It measures your interstitial glucose level which is glucose found in fluid
between the cells The sensor tests glucose every few minutes A transmitter wirelessly sends
the information to the LCD display To check the blood pressure of a person the vernier blood
pressure sensor is used to measure systemic arterial blood pressure To detect the body
temperature of a personMAX30205 is used The temperature sensor accurately measures
temperature This device converts the temperature measurements to digital form using a high-
resolution
Keywordsminus digital medi kit real-time glucose
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 12
DESIGN OF STATE FEEDBACK CONTROLLER FOR A FOUR
TANK PROCESS AND MONITORING USING IOT
MAtchaya1 KIshwarya2PRajeswari3 MRajalakshmi4 DrMSudalaimani5 1 2 3 4 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
5Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology
Virudhunagar India
E Mail ishwaryak96gmailcom
Abstractminus
Many Industrial Processes of manufacturing refining etc are non-linear time variant
sensitive to disturbances extremely complex and highly challenging to control The Four tank
system acts as the benchmark for the industrial processesThe dynamics of processes offers
great difficulty in controller design To control the process it is important to study the dynamic
behavior of the system which is helpful in the controller design The advanced control
techniques are generally imperative tasks due to the increasing complexity of the processes
Consequently the process industries need more reliable robust accurate and efficient control
systems for the operation of the industrial process The Proportional Integral Derivative (PID)
control scheme has been widely used in many of the industrial processes and dynamic
processes for controlling the industrial parameters Tuning of parameters of a PID controller is
essential for the satisfactory operation for process control Further the conventional tuning
methods are suited only for the open loop linear stable and single-input single-output systems
Hence the simplex controller suited for the four-tank system which is nonlinear has to be
designed In this paper observer based feedback controller is designed and implemented to
increase the accuracy and stability of the four tank systemThe aim is to determine the effective
controller algorithm for this four tank process so that the stability can be improved and to
control and monitor the same using IOT
Keywordsminus Four Tank System (4TS)mathematical modeling state feedback observer
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 13
MICROFLUIDIC APPROACH FOR CANCER CELL DETECTION
BSVindhuja1 JSuryamathi2 PArunkumar3 1 2 UG Scholar Department of Biomedical Engineering
SNS College of Technology Coimbatore India 3Assistant Professor Department of Biomedical Engineering
SNS College of Technology Coimbatore India
E Mailveenavindhuja123gmailcom
Abstractminus
Cancer has a major impact on society The number of cancer death is 1635 per 1 lakh
men and women per year Current diagnostic techniques for tumour metastasis include imaging
studies and serum marker assays however these results shows high rate of false negatives
because it lacks specificity The small sample volumes fast processing times multiplexing
capabilities and large surface-to-volume ratios inherent in microfluidic systems offer new
opportunities for cytology and cytopathology particularly for in vitro cell sorting and detection
Leveraging these advantages various microfluidic platforms have been developed for capturing
rare cells including circulating tumor cells (CTCs) circulating fetal cells and stem cells Here
we are reviewing the dielectroporesis method to separate the cancer cells from normal cells by
applying dc inhomogeneous dc electrical field to the particle in a microfluidic device
Keywordsminus cancer detection microfluids fabrication dielectroporesis sorting
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 14
AUTOMATION OF BELT CURING PROCESS USING
PLC
PrithiviRaj1 Syed karishma2 Kalyanasundaram3 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
E Mail prithivikcetgmailcom
Abstractminus
This paper mainly focuses on the technical improvement of curing system in the v-belt
manufacturing industry of Veegrip Pvt Ltd Based on the analysis of many experimental data
and under the consideration of economic benefit a series of theoretical indicators are concluded
and its favourable for realizing perfect production The main aim of this project is to automate
the process of V-belt autoclave curing Through the automation we can reduce man power and
improve the accuracy and perfectnessPLC applications are extensively used in manufacturing
industries to control the process so In this project we use VERSAMAX PLC for control
solenoids autoclaversquos cap and to maintain the temperature pressure in the autoclave
Keywordsminus AutomationProgrammable Logic Controllercuring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 15
AUTOMATIC IMMACULATION OF MILK SILO
GRPraveen1 ASamuvel2 BKaran Pandian3 JUma Maheshwari4 1 2 3 UG Scholar Department of Electronics and Instrumentation Engineering
Kamaraj College of Engineering and Technology Virudhunagar India
4Assistant Professor Department of Electronics and Instrumentation Engineering Kamaraj College of Engineering and Technology Virudhunagar India
E Mail praveenofficial1109gmailcom
Abstractminus
Cleaning-in-Place (CIP) is a crucial part to be automated in batch process industries In
many Process industries after completion of a batch the equipment cleaning is done by using
CIP process There are many methods used for cleaning the industrial equipments like tanks in
food and pharmaceutical industries such as 3-step 5-step and 7-step CIP In any industry once
the batch product is manufactured the equipments used for manufacturing should be cleaned to
have hygienic products The tanks pipes are cleaned with different chemical solutions such as
caustic acids enzymes etc To have an economical production sometimes the solutions are
recovered and reused This paper is primarily addicted with a scene to provide combination of
the concepts and application of automation of CIP in the process industries like food dairy
beverage and pharmaceutical verticals Proposed work for dairy industries contains CIP defined
for cleaning and sterilizing of tanks valves and pipes with the help of acid lye and consequent
sterilization with high energy efficiency
Keywordsminus Automation CIP Arduino Dairy
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 16
SMART HELMET
RVengat Rahul1 SVishnu Priya2 KSriramSiva3 PManikandan4
DrPSivakumar5 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
5 Professor Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
E Mailvengatrahulgmailcom
Abstractminus
The thought of developing this project came from social responsibility towards the
society As we can see many accidents occurring around us due to high speed mobile usage in
driving wrong traffic ruleswhile adjusting helmet Usually people die due to lack of treatment
in proper time The reasons for this may be many such as late arrival of ambulance no person
at place of accident to give information to the ambulance So this paper came up with idea of
giving the information about accident as soon as possible and in time Thus the death rate due
to bike accident can be minimized Here the vibration sensors in the helmet which are
connected to Arduino board that delivers a input when the rider crashes Based upon the sensor
valuethe Arduino extract GPS(Global Positioning System) data and then GSM(Global System
for Mobile communication) module automatically sends message to ambulance police and
family members with GPS location Then the accidents caused due to over fall of light at night
time can also be avoided here by helmet equipped with the feature automatic change of night
mode visor Also the android mobile communication can be done via Bluetooth module in the
helmet
Keywordsminus Vibration sensor GSM GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 17
DESIGN AND SIMULATION OF VIBRATION BASED
PIEZOELECTRIC ENERGY HARVESTER
STriphena1 Syed karishma2 RMsoundarya3 MKrishnasamy4 1 2 3 UG Scholar Department of Electronics and Communication Engineering Kalasalingam Academy of Research and Education Krishnankovil India
4Assistant Professor Department of Electronics and Communication Engineering
Kalasalingam Academy of Research and Education Krishnankovil India
E Mailtriphena04gmailcom
Abstractminus
Energy harvesting leads to enhancement demands for wireless sensor which is
developed for low power electronic devices Practical implementation of conventional linear
piezoelectric energy harvesters is not an effective solution because they suffer from narrow
operational bandwith due to their single resonant peak response in frequency spectrumThis
paper proposes a novel multimodal (four pronged spear)shaped (three degrees of
freedom)piezoelectric energy harvester to harness electrical energy from widebandlow
frequencyA single patch of piezoelectric material is used for power generation from multiple
modes of structureThis research mainly focus on vibration based piezoelectric energy
harvesting for low frequency(16-20Hz)Energy harvesting from natural low vibrations which
works as a self power system
KeywordsminusMultimodal harvest piezoelectric
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 18
RECOVERING MULTIPLE CELL UPSETS USING
LOW POWER ERROR CORRECTION CODES IN
MEMORY APPLICATION
ASaran1 SKrishnakumar2 1 UG Scholar Department of Electronics and Communication Engineering
Theni Kammavar Sangam College of Technology Theni India
2Assistant Professor Department of Electronics and Communication Engineering Theni Kammavar Sangam College of Technology Theni India
E Mailsarvan1240gmailcom
Abstractminus
Currently faults suffered by SRAM memory systems have increased due to the
aggressive CMOS integration density Thus the probability of occurrence of single-cell upsets
(SCUs) or multiple-cell upsets (MCUs) augments One of the main causes of MCUs in space
applications is cosmic radiation A common solution is the use of error correction codes
(ECCs) Nevertheless when using ECCs in space applications they must achieve a good
balance between error coverage and redundancy and their encodingdecoding circuits must be
efficient in terms of area power and delay Different codes have been proposed to tolerate
MCUs For instance Matrix codes use Hamming codes and parity checks in a bi-dimensional
layout to correct and detect some patterns of MCUs Recently presented columnndashlinendashcode
(CLC) has been designed to tolerate MCUs in space applications CLC is a modified Matrix
code based on extended Hamming codes and parity checks Nevertheless a common property
of these codes is the high redundancy introduced In this paper we present a series of new low
redundant ECCs able to correct MCUs with reduced area power and delay overheads Also
these new codes maintain or even improve memory error coverage with respect to Matrix and
CLC codes
Keywordsminus Error Correction codes fault-tolerance multiple-cell upsets reliability
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 19
THE BLUEBUG - IOT AND WIRELESS
PROGRAMMING SHIELD
BMahesh1 PPriyavarsha2 UKavitha3
1Assistant Professor Department of Electronics and Communication Engineering Solamalai College of Engineering Madurai India
1 2 UG Scholar Department of Electronics and Communication Engineering
Solamalai College of Engineering Madurai India
E Mail bmaheshmegmailcom
Abstractminus
BluBug wireless programming ampIoT device is the Multiple arduino shields integrated
into one that means Fancy a motor shield Bluetooth shield Wi-Fi shield sensor shield and a
wireless programming shield consolidated into one single board Buying a shield like motor
shield Bluetooth shield Wi-Fi shield sensor shield and a wireless programming shield for
every other purpose can have many drawbacks ndash the irritation of connecting and disconnecting
the shields soldering berg sticks on the shields the time and effort that goes into doing these
things and not to mention how heavy all this can be on our pockets BluBug solves all these
problems A time energy and money saving device for all your IoT projects Now monitor
sensor data and control motors from a remote location over the internet No more hassle of
plugging the Arduino to your PC - upload a code from the Arduino IDE wirelessly over
Bluetooth BluBug comes with an Android app for controlling robots via a virtual joystick
switching relays to make your home automation dream a reality observing live sensor behavior
from a distant place and a lot more cool stuff It also features a Bluetooth Terminal like
Arduinorsquos Serial Monitor
Keywordsminus Blue Tooth Motor Driver IoT Wi-Fi
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 20
LEUKOCYTE SEGMENTATION AND COUNTING
BASED ON HSV SATURATION COMPONENT
USING BLOB ANALYSIS
KRajesh1 PRevathi2 TSathiya3 PShalmiya4
1Assistant Professor Department of Electronics and Communication Engineering SSM Institute of Engineering and Technology Dindigul India
1 2 3 UG Scholar Department of Electronics and Communication Engineering
SSM Institute of Engineering and Technology Dindigul India
E Mail krajesh1980gmgmailcom
Abstractminus
Human blood is made up of three major cell types Red Blood Cells (RBC) White
Blood Cells (WBC) and platelets In our body each of them has its own functions RBC helps
with oxygen supply WBC fights infections and platelet helps blood clotting White blood cells
(WBCs) conjointly referred to as leukocytes or leucocytes area unit the cells of
the system that defend the body from communicable disease likewise as foreign invadersAll
white blood cells in the bone marrow are produced and derived from multipotent cells known
as hematopoietic stem cells Leukocytes are found throughout the body including the blood
and lymph system
Keywordsminus Otsu thresholding GLCM Acute Lymphoblastic Leukemia
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 21
ADVANCED MILITARY SPYING AND BOMB
DISPOSAL ROBOT
RKavitha1 MGayathri2 MKaviyapriya3 MDhivya Dharshini4 SMeena5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering Nadar Saraswathi College of Engineering and technology Theni India
E Mail kaviraviraji05gmailcom
Abstractminus
The Technical Improvement Together With The Need For High Performance Robots Created
Faster More Accurate And More Intelligent Robots Using New Robots Control Devices New Drives
And Advanced Control Algorithms The Presented Robot Control System Can Be Used For Different
Sophisticated Robot Applications This Spy And Bomb Detecting Robot Was Fully Controlled By The
Remote And The Commands From The Remote Via RF Transmitter Were Received By The Arduino So
This Spy And Bomb Detecting Robot Can Be Used In Military Applications Most Of The Military
Organization Now Takes The Help Of Robots To Carry Out Many Risky Jobs That Cannot Be Done By
The Soldier These Spy Robots Used In Military Are Usually Employed With The Integrated System
Including Gripper And Cameras Video Screens Sensors The Military Robots Also Have Different
Shapes According To The Purposes Of Each Robot Thus The Proposed System An Intelligent Robot
Using RF Module Saves Human Lives And Reduces Manual Error In Defense Side This Is Specially
Designed Spy And Bomb Detecting Robot System To Save Human Life And Protect The Country From
Enemies One Of The Most Important Things About These Robots Is That They Have The Capability To
Perform Missions Remotely In The Field Without Any Actual Danger To Human man
Keywordsminus RBC WBC WBS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 22
AUTOMATIC ENGINE LOCKER FOR DRUNKEN
DRIVERS
RVimali1 KSubiksha2 KNithyatharshini3 PHarinivashini4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail vimaliravi2707gmailcom
Abstractminus
Every day 60-80 of road accidents occur across the country The statistics show that
there are more than 10 motor vehicles related deaths per day many which are preventable
Road accidents due to motor vehicles occur for a variety of reasons The major reason for road
accident is discussed Drunken driving is the major cause for the road accidents Drivers drive
the vehicle under the influence of alcohol and causes damage to property and life We proposed
a system which would constantly monitor the drivers It detects the presence of alcohol If this
system detects the presence of alcohol it controls the engine This system can be installed in all
kind of vehicles and also ensures the safety of drivers as well as passengers
Keywordsminus Comparators motor drive relay buzzer motor MQ3 alcohol sensor
Automation CIP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 23
ZIGBEE BASED DEFENCE ROBOT
KHemalatha1 BLavanya2 SShakila Banu3 AAnushiya4 SMeena5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail hemalathakaruppasamy08gmailcom
Abstractminus
The Objective of this project is to design and implement intelligent mobile robot using
embedded microcontroller The robot is controlled from the pc in zigbeecommunication using
applicaton software Forwardrightmoveleft move and backward direction commands from the
application software will drive the robot in any desired direction also will run with the
application software microcontroller gets command from pc and transmit the information to
the robot Receiver microcontroller receives the data and performs the necessary movement of
the robot using DC motorssmoke Sensor is used to detect any fireBomb threat and indicating
to control roomwireless camera will be connected with receiver side microcontroller this
camera will monitor all the process simultaneously we can monitor those things in TV through
wireless tunerFurther the human precence can also be monitored using PIR sensorApplication
software is developed using high level programming language
Keywordsminus Defense robot robot navigation remote sensing and monitoring
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 24
AUTOMATIC SPEED CONTROL AND
ACCIDENCE AVOIDANCE SYSTEM MAnitha1 IMalarvizhi2 MNivetha3 RShanmugapriya4 KBharathikannan5
1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail sivaanithaecegmailcom
Abstractminus
The Objective of this project is to develop a system to keep the Vehicle
secure and protect it by the occupation of the intruders The main aim of the project is to
develop a system which automatically control the speed of vehicle and accidence avoidance
Vehicle is controlled automatically without any manual operation when any other obstacle at
particular distance away from the front vehicle Many accidents at High-ways are taking place
due to the close running of vehicles all of sudden if the in front vehicle driver reduces the
speed or applied breaks during the night is quite difficult to the following vehicle driver to
control his vehicle resulting accident This is mainly useful for the Drunken Drivers To avoid
this kind of accident we use the automatic speed control technique
Keywordsminus speed control automatic
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 25
WOMEN SAFETY DEVICE
MSmitha1 PPethana Dharshini2 APriyadharsini3 MSri Poorna Devi4
MArivalagan5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India 5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail msmitha1999gmailcom
Abstractminus
Safety is a very important issue due to rising crimes against women these days To help
resolve this issue we propose a gps based womens safety system that has dual security feature
This device consists of a system that ensures dual alerts in case a woman is harassed or she
thinks she is in trouble This system can be turned on by a woman in case she even thinks she
would be in trouble It is useful because once an incident occurs with a woman she may or may
not get the chance to press the emergency bu1048706on In a bu1048706on press aler_ng system in case a
woman is hit on the head from behind she may never get the chance to press panic bu1048706on and
no one will know she is in trouble Our system solves this problem This device is to be turned
on in advance by a woman in case she is walking on a lonely road or some dark alley or any
remote area Only the woman authen_cated to the devices can start the system by fingerprint
scan Once started the devices requires the woman to constantly scan her finger on the system
every 1 minute else the system now sends her loca_on to the authorized personnel number
through SMS message as a security measure and also sounds a buzzer con_nuously so that
nearby people may realize the situa_on In this case even if someone hits the woman or the
woman falls down and get unconscious she does not need to do anything the system does not
get her finger scan in 1 minute and it automa_cally starts the dual security feature This device
will prove to be very useful in saving lives as well as preven_ng atroci_es against women The
device uses GPS sensor along with a gsm modemlcd displayleds and microcontroller based
circuit to achieve this system
Keywordsminus women safety device GPS
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 26
BLACK-BOX SYSTEM ACCIDENT ANALYSIS
USING RASPBERRY PI
PDharani Shri1 VJothimeena2 SMariyam Zuhaa3 SSujitha4 SArul Oli5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail shrisivam3gmailcom
Abstractminus
Accident ration is increasing through every year so that analysis about the accident is
very essential normally in Flights the black box will be present to analyze every parameter of
flight if there any accident occurs then they will first search for black box which will have
every parameter log about the flight which gets crashed It is implemented in Raspberry Pi at
low cost Which also sent to the transport department through MQTT protocol Which is
transmitted as quick speed when compared to HTTP protocol since MQTT protocol is
lightweight protocolThis Raspberry Pi system which monitors the car speed alcohol detection
and also transmit those data logs through MQTT protocol so that if there any accident happens
it is identified by studying the catalogs which we obtained from the MQTT protocol which the
MQTT is lightweight protocol consist three layers Publisher Broker and Subscriber Even if
the Subscriber is connecte3d in the centralized node called Broker data get stored in that node
and it sent to the subscriber when the subscriber comes into the network Main advantage of
MQTT is that is lightweight protocol even in low internet speed it can send the data
Keywordsminus MQTT HTTP
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 27
TECHNO TOLLBOOTH USING RFID TAG amp GSM
TECHNOLOGY
PPavithra1 PPriyadharshini2 SDhivya3 GSafrena4 KSangeetha5 1 2 3 4 UG Scholar Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
5Assistant Professor Department of Electronics and Communication Engineering
Nadar Saraswathi College of Engineering and technology Theni India
E Mail priyadarshinipalanichamygmailcom
Abstractminus
ATCS usually known as ldquoAutomated Toll Collection Systemrdquo is a new technology for
collecting toll in a faster and more efficient way It is a great alternative to long waiting at
manual toll plazas In order to overcome the wastage of time and fuel at same time we have
come up with a concept of RFID based automated toll collection system using Arduino RFID
stands for Radio Frequency Identification these cards are unique identities provided to every
vehicle by Registration Office at each city Whenever a vehicle with such Unique ID reaches
the toll plaza the RFID card reader attached on the toll plaza gate reads the card and transfers
the unique ID to Arduino ATmega 328 Accordingly the processor works and deducts a fixed
money from the prepaid card If the cardrsquos ID is valid and has sufficient balance the processor
will command the DC motor to start and open the gate letting the vehicle to pass On passing
from the gate the screen will show the deducted and current balance of the card If the card is
not valid or low in balance it will prompt to move the vehicle to manual toll collection lane
Furthermore a message will be sent to the ownerrsquos registered mobile number with the same
details along with the location of the toll booth
Keywordsminus ATCS RFID ATMega328 SIM900
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 28
SELF ADAPTIVE ENERGY EFFICIENT DATA COLLECTION IN
WIRELESS SENSOR NETWORKS AAntonio Reshme1 ANarendra Kumar2
PG Student1 Professor2
antonioreshmeecegmailcom1 nandhumegmailcom2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Wireless Sensor Networks (WSNs) are normally self-sorted out remote adhoc systems created
by large number of low cost small scale sensor nodes These nodes are little in size and are
worked by battery sources which cant be effectively replaced or recharged Because of energy
requirement the node must total a predefined task with minimum energy dissipation and
prolong the systems lifetime In WSN during the data transmission stage sleepwake-up
scheduling is additionally one of the key issues The purpose for sleepwake-up scheduling is to
save the energy of every node by keeping nodes in rest mode to the extent that this would be
possible and subsequently expanding their lifetime In this paper a Self Adaptive-SleepWake-
up Scheduling (SA-SWS) protocol utilizing Cooperative Media Access Control (CMAC)
allocates the timeslots to forward information from the source to sink The nodes which are
having the most noteworthy residual energy are chosen as the forwarding nodes In this
methodology the reinforcement learning technique was utilized to empower every node to
independently choose its very own operation mode in a decentralized way Simulation results
exhibit the great performance compared with the other methodology for previously mentioned
problem
Index Terms Wireless Sensor Networks (WSN) Self Adaptive SleepWake-up
Scheduling (SA-SWS) Cooperative Media Access Control (CMAC)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)
INTERNATIONAL CONFERENCE ON NEW SCIENTIFIC CREATIONS IN ENGINEERING amp
TECHNOLOGY (ICNSCET) 2019
ELECTRONICS AND COMMUNICATION ENGINEERING | ICNSCETrsquo19 29
IMPROVED CYCLOSTATIONARY DETECTION BASED
SPECTRUM SENSING TECHNIQUE IN COGNITIVE RADIO
NETWORKS S Anusha Priya1 J Julie Antony Roselin2
PG Student1Assistant Professor2
Department of Electronics and Communication Engineering
VV College of Engineering
Abstract
Cognitive Radio (CR) is an intelligent device which is aware of the environment and its
changes and can automatically detect available channels in a wireless spectrum CR has been
used to limit natural resourses efficiently without any interference to Primary Users (PUs) and
can coexist with licensed user Reliable detection of Primary Users in the presence of noise is a
crucial problem in Cognitive Radio Networks (CRN) To address the above issue spectrum
sensing based on Cyclostationary Feature Detection (CFD) is proposed which can robustly
detect hidden primary signals even in low Signal to Noise Ratio (SNR) Here CFD method is
used to investigate the problem of detecting vacant spectral bands Probability of detection is
more precise in CFD which accurately detects the presence of an active primary user by
computing the Spectral Correlation Function (SCF) which applies only to the cyclostationary
processes whereas stationary processes do not exhibit spectral correlation density In this
regards the parameters such as the Probability of detection Probability of false alarm and the
Signal to Noise ratio (SNR) are used to find the vacant frequency bands Thus this method is
more reliable than traditional energy detection scheme as CFD can perfectly distinguish
primary user signal from noise and can perform efficiently even in low SNR region and also in
fading environments
Index Terms Cognitive Radio (CR) Cyclostationary Feature Detection (CFD) Spectrum
Sensing Cyclic Autocorrelation Function (CAF) Spectral Correlation Function (SCF)