8/4/2019 Working in Hot Environments
1/108
8/4/2019 Working in Hot Environments
2/108
Emergency Information
Company Emergency Phone Number
Poison Control Centre
Doctor
Ambulance
Fire
Police
Prepared by
Canadian Centre for Occupational Health and SafetyHamilton, Ontario, Canada
CCOHS, 2005
8/4/2019 Working in Hot Environments
3/108
First Edition
Working in HotEnvironments: A Health
and Safety Guide
Published 2005
P05-1EISBN 0-660-19453-8
DSS Catalogue Number CC273-2/05-1E
Canada: $10.00 (+ GST)
US/Others: $10.00 (USD)(Prices subject to change without notice)
8/4/2019 Working in Hot Environments
4/108
Personal Information
This handbook belongs to:
Name
Company
Position
Address
Telephone
Doctor
Telephone
Allergies
Medical Conditions
In case of emergency please notify:
Name
Relation
Address
Telephone
8/4/2019 Working in Hot Environments
5/108
Working in Hot Environments: A Healthand Safety Guide
Objectives
The guide will help health and safety committeemembers and representatives as well as supervisors,managers, engineers and other health and safetyprofessionals to:
1. Conduct hazard assessment of heat exposure inthe workplace.
2. Identify risk factors for work in hot environments.
3. Develop prevention programs and practices toreduce injury and illness.
4. Plan problem-solving actions through employeeand management involvement.
5. Develop hazard controls based on the mostcurrent knowledge in the field of occupationalhealth and safety.
6. Comply with legal requirements.
Scope
The guide provides:
Practical guidance for the identification, assess-ment and control of the health and safety hazardsrelated to working in hot environments; and
Applicable legislation, standards and guidelines
addressing heat stress.
Detailed information on specific workplace hazardscan be obtained from the Inquiries Service of theCanadian Centre for Occupational Health and Safety(CCOHS).
8/4/2019 Working in Hot Environments
6/108
Target Audience
The guide is intended to serve as a handy reference for
health and safety committee members, health and safetyrepresentatives, employees, supervisors and managers.
For training sessions, the guide can serve as a practicalhandout for future reference.
Summary
Heat stress is the net heat load on the body from thecombined effect of hot environmental conditions (airtemperature, radiant heat, humidity and air movement),internal body heat due to physical activity, and clothingrequirements. Workplaces and occupations associatedwith excessive heat exposure include: foundries, steelmills, bakeries, construction sites, kitchens, grounds
maintenance, dishwashing and steaming.Heat strain is the overall response of the body resultingfrom heat stress. It can cause a wide variety of healthdisorders. Heat stroke is the most serious health risk,which can be fatal if medical attention is not availablepromptly. People doing heavy physical work in hot andhumid conditions are affected more than those doing
light work.
Heat stress is largely preventable by engineering andadministrative control methods. As a last resort or inextreme conditions, the use of personal protection iswarranted. Engineering controls are designed toeliminate or minimize the level of heat exposure at thesource of the hazard. Administrative controls reduceheat exposure at the worker. These measures includeestablishing procedures for acclimatization of newworkers, training in safe work practices, reducing theduration of work in hot environments and providingplenty of drinking water. Workers and supervisorsmust receive adequate training and education to beable to recognize early symptoms of health disordersand seek timely medical help.
8/4/2019 Working in Hot Environments
7/108
Under excessively hot working conditions, personalprotective equipment such as cooling vests, hats andother body cooling equipment may be necessary.
It might be necessary to stop work in extremely hotconditions.
Employers can prevent or minimize heat stress hazardsby implementing appropriate policies and programs.A workplace heat stress policy must include clearlydefined procedures for working safely in hotenvironments and for providing care to potential heat
stroke victims.
8/4/2019 Working in Hot Environments
8/108
8/4/2019 Working in Hot Environments
9/108
Table of Contents
IntroductionSection 1. Legal Responsibilities to Prevent Heat Stress
1. Responsibilities as set out in Health
and Safety legislation...............................................2
2. Ways of meeting responsibilities: being prepared.......3
Section 2. The Bodys Response to Hot Environments1. The bodys heat balance ..............................................8
2. Heat exchange between the body
and the environment.................................................9
3. Effect of clothing.......................................................13
4. Other contributing factors .........................................13
Section 3. Safety and Health Concerns
1. Safety Concerns.........................................................16
2. Health Concerns
(a) Heat Strain ..........................................................16
(b) Heat-related illnesses..........................................18
Section 4 Measures of Heat Exposure
1. Measures of Occupational Heat Exposure: ..............26
The WBGT index
2. Environmental Measures of Heat Exposure..............30
Section 5 Heat Exposure Standards and Guidelines
1. Occupational exposure limits ....................................32
2. Thermal comfort guidelines for offices.....................40
8/4/2019 Working in Hot Environments
10/108
Section 6. Control Measures
1. Engineering Controls.................................................42
2. Administrative Controls ............................................45
3. Personal Protection....................................................50
4. Sample Safe Work Practices......................................53
Section 7. Occupational Health and Safety Legislation.
1. Canadian Legislation.................................................58
2. US Legislation...........................................................61
Section 8. Sources of Additional Information.
1. Canadian Government Departments with .................64
ResponsibilityOccupational Health and Safety
2. US Federal Safety and Health Agencies ...................69
Section 9. Bibliography and Internet Links 73
Section 10. Appendices
A. A summary of health hazards and ...........................78
preventive measures
B. The Humidex ............................................................79C. Safety tips for different levels of the UV index ......81
D. Glossary ....................................................................83
E. Abbreviations ...........................................................85
F. Sample heat stress policy and checklist ...................87
G. Case histories: fatalities from occupational ............ 92
heat exposure
8/4/2019 Working in Hot Environments
11/108
Introduction
Everyone likes warm weather. However, when it
becomes too hot we feel discomfort. Working undervery hot conditions can cause serious adverse healtheffects. Examples of hot working conditions include:
Working in foundries, steel mills, smelters andglass factories.
Working near furnaces and extremely hot ormolten metals.
Outdoor work such as construction, road repair,open-pit mining and farming in summer months.
Working in laundries, restaurant kitchens, bakeriesand canneries.
In a hot working environment, how hot we feeldepends on the following factors:
air temperature;
relative humidity (moisture content of the air);
air movement;
physical exertion (heavy workload produces morebody heat than light work); and,
clothing.The combined effect of the environmental factors (airtemperature, relative humidity and air movement) areexpressed as the wet bulb globe temperature index,commonly known as WBGT. For occupationalexposures WBGT is used as an overall measureof heat exposure.
In this guide we frequently use the terms heat stress,heat strain and heat-related illnesses. Heat Stress isthe overall heat load on the body, including environ-mental heat and inner body heat production due toheavy workload. Heat Strain refers to the bodysresponse to heat stress. Heat-Related Illnesses refers toadverse health effects due to heat stress.
8/4/2019 Working in Hot Environments
12/108
The bodys defense mechanisms make adjustments todeal with moderate excess heat exposure. In extremelyhot working conditions, the risk of heat-related illnesses
increases. Heat stroke is the most severe adversehealth effect related to heat exposure. It can be fatalunless medical attention is provided immediately.
In a particular hot environment, everyone is not affect-ed equally. Some individuals are more susceptiblethan others to extreme heat and may be at greater risk.Personal factors such as body weight, diet, level of
acclimatization, medications and alcohol consumptioncontribute to how an individual responds to hot work-ing conditions. It is important to consider individualsusceptibility when developing safe work practices.
The guide provides information to assist workers andtheir supervisors with the recognition and prevention
of heat-related illnesses. The main purpose of theguide is to emphasize the importance of developingsafe work practices and implementing preventivemeasures to prevent (or minimize) worker exposureto extreme heat.
8/4/2019 Working in Hot Environments
13/108
Section 1
Legal Responsibilitiesto Prevent Heat Stress
1. Responsibilities as set out in Health and
Safety legislation.
2. Ways of meeting responsibilities:being prepared.
8/4/2019 Working in Hot Environments
14/108
2
Employers are obliged to prevent heat-related illnessesand fatalities. Such responsibilities are the same asthose for other occupational hazards such as noise,
chemicals and radiation.
1. Responsibilities as set out in Healthand Safety legislation.
Some jurisdictions may not have health and safetyregulations specifying occupational heat exposure limits.
This does not mean that employers do not haveobligations to protect employees from harmful heatexposures.
Under the general duty clause of the OccupationalHealth and Safety Act (Canada Labour Code Part IIfor federal jurisdiction), employers are responsible to
protect the health and safety of employees. For example,the Canada Labour Code Part II states:
Every employer shall ensure that the health and safetyat work of every person employed by the employer isprotected. Canada Labour Code Part II, section 124.
All provincial and territorial OSH acts have similar
provisions. Therefore, employers have a legalresponsibility to protect employees from harmfulheat exposure.
8/4/2019 Working in Hot Environments
15/108
3
2. Ways of meeting OHS responsibilities:being prepared.
The purpose of being prepared to meet OHSresponsibilities is to prevent heat-related illnesses fromoccurring and reduce the impact of potentially harmfulheat exposure situations.
In order to meet their health and safety responsibilities,employers must:
1. Identify conditions that pose a risk of heat-relatedillness;
2. Evaluate the risk of adverse health effects;
3. Develop and implement a prevention program inconsultation with the health and safety committee;
4. Evaluate the effectiveness of the program; and,
5. Periodically review the heat stress policy andprogram and make continuous improvements inconsultation with the health and safety committee.
Supervisors have legal responsibilities to ensure thatemployees work safely. In order to meet theirresponsibilities, supervisors must:
1. Identify potential heat stress situations in theirworkplace;
2. Ensure that employees follow safety proceduresrequired by the employer;
3. Take every precaution reasonable in thecircumstances for the protection of employees; and,
4. Ensure that changes of equipment or process aredone only after evaluation of their impact onemployee health and safety.
Workers are responsible too. They must:
1. Follow safe work practices established by theemployer; and,
2. Report unsafe conditions to their supervisor.
8/4/2019 Working in Hot Environments
16/108
4
A heat stress policy and program is a systematic planof action designed to prevent heat stress and relatedadverse health effects. Because needs differ from one
workplace to another, a prevention program developedfor one workplace may not serve the needs of others.It is vital to develop and implement a workplace-specificprevention program in consultation with the workplacehealth and safety committee.
Following are the basic elements of a heat stressprevention program.
Conformity with the company healthand safety policy.
Conformity with the occupational healthand safety legislation.
Conformity with the overall workplace healthand safety policy and program.
A time frame for implementation and completion.
Provision for regular monitoring and review.
Procedures for keeping records of the successesand problems of the program.
Clearly defined roles and responsibilities.
Employee orientation. Job specific training.
Reporting and investigating incidents.
Emergency procedures.
Medical and first aid procedures.
8/4/2019 Working in Hot Environments
17/108
5
All persons working in hot conditions must receiveadequate training and education so that they are ableto recognize early warning signs and symptoms of
heat-related illnesses, especially heat stroke.Individuals affected by heat stroke are usually unableto recognize their own symptoms. The survival of heatstroke victims depends on the coworkers ability toidentify the signs and symptoms of heat stroke andtake timely action.
Provide prompt medical attention to heat stroke victims
8/4/2019 Working in Hot Environments
18/108
8/4/2019 Working in Hot Environments
19/108
Section 2
The Bodys Response toHot Environments.
1. The bodys heat balance.
2. Heat exchange between the bodyand the environment.
3. Effect of clothing.
4. Other contributing factors.
8/4/2019 Working in Hot Environments
20/108
8
1. The bodys heat balance.A healthy human body maintains its internal temperature
(core temperature) around 37C. Variations, usually ofless than 1C, may occur with the time of the day,level of physical activity or emotional state.
In order to maintain a constant body temperature, thebody must continuously lose as much heat as it gains.This implies that when it is hot, our body must lose moreheat compared to the heat loss in a cool environment.
Hot
Very Hot
EX
TREME
CA
UTION
CAUTION
LESSHAZARD
OUS
8/4/2019 Working in Hot Environments
21/108
9
The body gains heat in two ways:
1. Metabolic (inner body) heat production.
2. Heat gain from the environment.Metabolic heat is the heat produced within the body. Itis a result of the physical and chemical processes thattake place within the body for continued growth,functioning and movement. Even when we are sittingquietly, the bodys internal processes are active andproduce some amount of metabolic heat. The
metabolic heat production increases with increase inthe physical activity.
Heat gain from the environment occurs from contactwith the surrounding hot air and from hot objects inthe vicinity. As the environment warms-up, the bodytends to warm-up as well. The body's internalthermostat maintains constant inner body temperature
by increasing the body heat loss to offset increasedheat gain from the environment.
8/4/2019 Working in Hot Environments
22/108
10
2. Heat exchange between the body andthe environment
There are three main ways the body exchanges heatwith its surroundings:
Radiation
Convection
Sweat evaporation
Radiation is the direct heat exchange between the bodyand an object without direct contact with the object.
The body gains heat from surrounding hot objects,such as hot metal, furnaces or steam pipes.
The body loses heat to cold objects, such aschilled metallic surfaces.
No radiant heat gain or loss occurs when thetemperature of surrounding objects is the same asthe skin temperature (about 35C).
When we stand in the sun, we feel warm because ourbody receives heat from the sun by the radiation process.
Radiant heat is the main concern when working near
hot objects or outdoors on a hot and sunny summerday. Radiant heat can come directly from hot objectsand also as reflection from nearby surfaces.
Convection is the process by which the bodyexchanges heat by contact with the surrounding air.
The body gains heat from the hot air that comes incontact with the body; for example, hot air comingfrom heating vents.
The body looses heat to cold air that comes incontact with the skin; for example, cold draftfrom leaky outside doors.
8/4/2019 Working in Hot Environments
23/108
11
Convective heat exchange increases when:
Air speed increases; and/or
The difference between air temperature and skintemperature increases.
Sweat Evaporation cools the body. Cooling by sweatevaporation increases when:
Wind speed increases; and
Relative humidity (the moisture content of the air)
decreases.
Besides radiation, convection and sweat evaporation,a small amount of heat is lost through conduction andrespiration.
8/4/2019 Working in Hot Environments
24/108
12
Conduction is the process in which the bodyexchanges heat with an object that comes in contactwith the body. Usually, bodys heat gain or loss by
conduction process is very small compared to the heatexchange by radiation, convection and sweat evapora-tion processes.
Respiration contributes to a very small amount ofheat exchange between the body and the inhaled hotair. The amount of heat exchanged through breathingis very small and can be ignored in assessing heat
stress.
1. When body core temperature rises
Blood flow to skin increases
Sweating increases Heart rate increases to move blood to the skin
2. When this works well
Core temperature drops or stabilizes at a safe level
Normal Cooling Mechanisms
1. Heat exhaustion and heat stroke occur when the body issubjected to more heat than it can cope with
Heat Stress
8/4/2019 Working in Hot Environments
25/108
13
1. The body becomes unable to control its innerbody temperature
2. Death or permanent damage may occur if medical treatment is
not given promptly
3. Symptoms
No sweating
Red, hot, dry skin Throbbing headache Dizziness Nausea
Heat Stroke
8/4/2019 Working in Hot Environments
26/108
3. Effect of ClothingClothing affects heat exchange between the body and
the environment. Heavy clothing that fails tobreathe does not allow the body to cool off by aircirculation and sweat evaporation processes.
Cool Down by removing clothes
4. Other contributing factorsIn addition to high temperature and humidity, theeffect of heat stress on the body depends on severalindividual factors such as general health and lack ofacclimatization. Certain medications such asantihistamines, cold remedies, diuretics, tranquilizers,etc. may cause heat intolerance by decreasing sweat-
ing or increasing urination. People taking such medica-tions must consult their doctor about their ability towork in hot environments.
8/4/2019 Working in Hot Environments
27/108
Section 3
Safety and HealthConcerns.
1. Safety Concerns
2. Health Concerns
(a) Heat Strain
(b) Heat-related illnesses
8/4/2019 Working in Hot Environments
28/108
16
1. Safety concernsHeat stress can cause safety problems by impairing a
workers ability to work safely. Heat can lead to accidentsresulting from the slipperiness of sweaty palms and toaccidental contact with hot surfaces. Heat causesdizziness. Heat may also affect mental alertness andphysical ability to work increasing the risk of incidents.As a worker moves from a cold to a hot environment,fogging of eyeglasses can briefly obscure vision,
presenting a safety hazard.
2. Health Concerns
(a) Heat Strain
Heat strain is the response of the body to heat exposure.
It is a series of physiological responses to heat stress.Excessive and prolonged heat strain can causeheat-related illnesses. An early recognition of heatstrain signs and symptoms will help in preventingpotentially serious health disorders.
The severity of heat strain varies greatly from one personto another. Some highly susceptible individuals are
affected sooner than others. However, as the level ofexposure and/or the exposure duration increases moreand more people are likely to be affected. The signsand symptoms of heat strain include:
Sweating
Discontinued sweating
Increased heart rate
Increased inner body temperature
Urinating less frequently than normal
Small volume of dark-colored urine
Irritability
Lack of coordination Lack of judgement
8/4/2019 Working in Hot Environments
29/108
17
Sweating:
The presence of sweat on the skin, or sweat-soakedclothing, is a sign of heat strain.
Sweat evaporation cools the body. Commonly usedmethods to increase the sweat evaporation rate are:
Increasing the air flow rate over skin and clothingsurfaces.
Lowering the ambient temperature and relative
humidity. Reducing radiant heat gain from the sun and hot
objects in the vicinity.
Reducing the level of physical activity (metabolicheat production).
Discontinued sweating:
Absence of sweating in a very hot environment canbe a sign of potential heat stroke. Affected personsrequire immediate first aid and medical attention.
Increased heart rate:
An increase in the heart rate is an indication that thebody has to work harder than normal to cope withthe increased heat load.
Increased inner body temperature:
When the body is unable to cope with the hotenvironment, the bodys heat gain exceeds the bodyscapability to lose heat. As a result, the inner bodytemperature rises increasing the risk of heat-relatedillnesses.
8/4/2019 Working in Hot Environments
30/108
18
Decreased frequency and volume of urination andchange in the colour of urine:
In hot environments the volume of urine and thefrequency of urination decrease because of loss ofbody fluids through sweating. These are warning signsof dehydration. People need to develop a habit ofdrinking adequate volumes of water at frequent intervalsto maintain their normal frequency ofurination, urine colour and urine volume.
(b) Heat-Related illnesses
Prolonged exposure to hot working conditions cancause a wide range of adverse health effects.Commonly known heat illnesses are:
Heat rash
Heat edema Heat cramp
Heat exhaustion
Heat syncope (fainting)
Heat stroke
Signs and symptoms of heat illnesses include:
Excessive sweating
Rapid breathing
Weakness or fainting
Tiredness
Headache
Confusion
Heat Rash,also called prickly heat or miliaria, is acondition in which areas of the skin itch intensely andoften feel prickly, or sting. Heat rash looks like tinybumps surrounded by a zone of red skin. It usuallyoccurs on clothed parts of the body, such as the back,abdomen, neck, upper chest, groin, or armpits andgoes away within a few days.
8/4/2019 Working in Hot Environments
31/108
19
Heat edema is swelling which generally occursamong people who are not acclimatized to working inhot conditions. Swelling is often most noticeable in
the ankles.
Heat cramps are painful muscle cramps, which resultfrom excessive loss of salt from the body. Muscles ofthe extremities and the abdominal wall are usuallyinvolved. Heat cramps are promptly relieved when theindividual takes drinks that replace the body electrolytes,and rests in a cool environment.
Heat exhaustion occurs as a result of excessive lossof water and salt from the body. The symptoms includeheavy perspiration, flushed skin and low blood pressure.
Prompt recovery occurs when the affected individualmoves to a cool environment, takes rest and drinks wateror beverages with adequate water and electrolyte content.
Heat Syncope is a sudden dizziness experienced afterphysical exertion in a hot environment. The skinappears pale and sweaty but is generally moist andcool. The pulse may be weakened, and the heart rate isusually rapid. Body temperature is normal.
Heat Stroke
Heat stroke is a medical emergency, which can be fatalunless first aid and medical help is promptly provided.If you or someone you are with becomes ill, hasdifficulty in breathing, or feels confused or disoriented,SEEK MEDICAL ATTENTION IMMEDIATELY.
8/4/2019 Working in Hot Environments
32/108
20
Heat stroke signs and symptoms include:
Extremely high body temperatures (above 41C).
Mental confusion, delirium, or coma. Absence of sweating.
Complete or partial loss of consciousness.
Red, hot, and dry skin (no sweating).
Rapid, strong pulse.
Throbbing headache.
Dizziness.
The following actions are basic elements of a first response:
TAKE the affected person to a cooler area (for example,an air-conditioned shed or air-conditioned vehicle).
REMOVE excess clothing (hard hat, boots, shirt).GIVE the person water to drink, if conscious.
ALLOW the person to rest.
COOL the persons body with cool water, coldcompresses, and/or rapid fanning.
TAKE the person to medical facility for propermedical care.
Risk of heat stroke is higher than normal if a person is:
Not fully acclimatized;
Not in good physical health;
Ill as a result of pre-existing diarrhea or fever; or,
Recovering from a heat-related illness.
A case of heat stroke should be taken as a warning. Itindicates a possibility that other workers could beaffected. It is important to take immediate remedialaction to prevent future recurrence of heat strokes insimilar environments.
8/4/2019 Working in Hot Environments
33/108
21
Illnesses caused by long-term (chronic) heatexposure
Some researchers have reported that certain disordersof the kidney, liver, heart, digestive system, centralnervous system and skin may be linked to long-termheat exposure. Other probable effects include: chronicheat exhaustion, sleep disturbances and susceptibilityto minor injuries. There is no conclusive scientificevidence linking such effects and long-tem exposureto heat.
Effect on the eye due to long-term (chronic) heatexposure
The eye has no heat sensors and no blood vessels tocarry heat away. The lens of the eye is particularlyvulnerable to radiant heat from red-hot objects
(infrared radiation). Following are some examples ofsources of radiant heat exposure:
Glass products manufacturing plants.
Iron, steel and nonferrous foundries.
Brick-firing and ceramics operations.
Bakeries.Glass blowers and furnace-men may develop cataractsafter many years of exposure to radiant heat from hotobjects. Foundry workers, blacksmiths and ovenoperators are also exposed to potentially harmful levelsof infrared radiation.
Medications that may affect heat illnessesCertain medications can affect heat tolerance. Peopletaking medications must ask their doctor if they needto be extra careful when working in hot environments.
The following table summarizes the symptoms,treatment and preventive actions for common
heat-related illnesses.
8/4/2019 Working in Hot Environments
34/108
22
Recognitionand
PreventionofHeatRelatedIllne
sses
H
eatrelated
il
lness
H
eatRash
H
eatCramps
Symp
toms
-Red
bumpyrashwith
severeitching
-Pain
fulcrampsinarms,
legs
ors
tomach
-Can
occursuddenlyatwork
orlaterathome
-Cram
pscanbeawarningof
othe
rmoredangerousheat
indu
cedillness
Treatments
-Changeintod
ryclothes
-Avoidhotenv
ironments
-Rinseskinwithcoolwater
-Movetoacoolarea
-Loosenclothing
-Drinkcoolsa
ltedwater(1tsp.
saltpe
r
gallonofwat
er)orcommercialfluid
replacement
beverage
-Seekmedical
aidifcrampsareserious
Prevention
-Washregularly
to
keepskinclean
anddry
-Usesaltinfood
(ifonalow
saltdiet,
discusswitha
doctor)
-Saltinfoodwillgive
thebodyallthe
salt
thebodyneeds
8/4/2019 Working in Hot Environments
35/108
23
Hea
trelated
illne
ss
Fain
ting
(hea
tsyncope)
HeatExhaustion
Sympto
ms
-Sudden
fainting
-Coolmoistskin
-Weak
pulse
-Heavysweating
-Coolmoistskin
-Bodytemperatureover38C
-Weak
pulse
-Norm
alorlowbloodpressure
-Person
istired,
weak,
clums
y,
upsetorconfused
-Person
isverythirsty
-Person
ispanting
or
breathing
rapidly
-Person'svision
is
blurred
Treatments
-Fainting
maybedueto
aheartattack
-GetMedicalaid
-Assessneedfo
rCPR
-Moveto
acool
area
-Loosen
Clothin
g
-Maketheperson
liedown
-Offersipsofcoo
lwaterifpersoniscons
cious
-GETMEDICAL
AID.
Thiscondition
can
leadto
heatstroke,
which
can
kill
-Movetheperso
n
to
acool,shadedarea
-Loosen
orremoveexcessclothing
-Providecoolw
aterto
drink
(saltedifpossible)
-Fan
andspraywith
coolwater
Prevention
-Reducephysi
cal
activity
levels
and/or
heatexposure
-Drinkfluidsre
gularly
-Checkon
eac
h
other
to
helpspott
he
signsandsym
ptoms
thatoften
pre
cede
heatstroke
-Reducephysical
activity
levels
and/or
heatexposure
-Drinkfluidsre
gularly
-Checkon
each
other
to
helpspott
he
symptomsth
atoften
precedeheat
stroke
8/4/2019 Working in Hot Environments
36/108
24
H
eatrelated
illness
H
eatStroke
Symp
toms
-Highbodytemperature
(over41C)
-Personisweak
-Con
fused,
upsetor
actingstrangely
-Personhashot,
dry,
redskin,
a
fastpulse,
ora
headacheo
r
dizziness
-Inlaterstagesa
personpas
ses
out
andhasconvulsions
Treatments
-CALLAMBUL
ANCE.
Thisconditionc
an
killa
person
quickly
-Remove
excessclothing
-Fanandspra
ythe
personwithcoolwater
-Offersipsof
coolwater
Prevention
-Reduce
physical
activitylevelsand/or
heatexposur
e
-Drink
fluidsr
egularly
-Check
oneac
hother
to
helpspot
the
symptomsth
atoften
precede
heat
stroke
-Learnto
recognize
warningsign
sofa
heatstroke
Source:OntarioMinistryof
Labour,OccupationalHealthandSafetyDivision,
Gui
de
to
HeatStress
"http://www.g
ov.p
e.c
a/phot
os/original/wcb_
heat_
stres
s.p
df"www.g
ov.p
e.c
a/photos/original/wcb_
heat_
stress.p
df
8/4/2019 Working in Hot Environments
37/108
Section 4
Measures of HeatExposure
1. Measures of Occupational Heat Exposure:
The WBGT index
2. Environmental Measures of Heat Exposure
8/4/2019 Working in Hot Environments
38/108
26
1. Measures of Occupational HeatExposure: The WGBT Index.
How hot we feel depends on the combined effect ofthe following environmental and workload factors:
Temperature of the surrounding air.
Radiant heat from the sun and other hot objects inthe vicinity.
Relative humidity (moisture content of thesurrounding air).
Speed of air movement.
Level of physical activity.
WBGT (Wet Bulb Globe Temperature) index
The Wet Bulb Globe Temperature (WBGT) indextakes into account all the environmental factors, i.e.,air temperature, radiant heat, humidity and airmovement speed, and gives a single number measureof the perceived heat.
WBGT is calculated by using one of the followingtwo formulas:
1. With direct exposure to sunlight:
WBGTout = 0.7 Tnwb + 0.2 Tg + 0.1 Tdb
2. Without direct exposure to the sun:
WBGTin = 0.7 Tnwb + 0.3 Tg
Abbreviations used in the above formula are as follows:Tnwb = natural wet-bulb temperature (accounts for
cooling due to sweat evaporation).
Tg = globe temperature (accounts for the radiantheat exposure).
Tdb = dry-bulb (accounts for air temperature).
Occupational exposure limits are generally given inWBGT units.
8/4/2019 Working in Hot Environments
39/108
27
Instrumentation for measuring WBGT
A WBGT monitoring instrument consists of:
1. A dry-bulb thermometer to measure air tempera-ture (Tdb).
2. A natural (static) wet-bulb thermometer to meas-ure evaporative temperature (Tnwb).
3. A black globe thermometer to measure radianttemperature (Tg).
A Dry bulb thermometer is an ordinary thermometercommonly used to measure the air temperature. The bulbof the thermometer must be shielded from the sun andother hot objects in the vicinity to prevent radiant heatfrom reaching the thermometer bulb. However the shieldshould not interfere with the airflow around the bulb.
A Natural wet bulb thermometer has a wet wickcovering its bulb.
The wick must be wetted by direct application ofwater from a syringe one-half hour before eachreading.
The wick must cover the bulb of the thermometer
and an equal length of additional wick must coverthe stem above the bulb.
The wick must be replaced periodically to avoidsalt and dirt accumulation.
8/4/2019 Working in Hot Environments
40/108
28
A Globe thermometer consists of a 15 cm (6 inch) indiameter hollow copper sphere painted on the outsidewith a matte black finish. The thermometer bulb or
another temperature sensor is fixed in the center of theinterior of the sphere.
The following diagram illustrates the components of aWBGT monitoring instrument.
Helpful tips for using a WBGT monitor
FOLLOW operating instructions provided by theequipment manufacturer.
PLACE the monitor as close as possible to theposition of the worker involved.
AVOID placing the monitor close to a hot surface orin a draft unless this represents an actual conditionof the workers environment.
8/4/2019 Working in Hot Environments
41/108
29
ENSURE that the wick is damp at all times. Use onlydistilled water.
ALLOW about 25 minutes for the unit to stabilizeafter it has been set up.
Personal Heat Stress Monitors
Personal heat stress monitors are commerciallyavailable. These are convenient to use to monitor theworker exposure during a work shift. Personal
monitors are generally equipped with a data loggingsystem, which stores and displays temperature dataand warns the worker when pre-set temperaturethresholds are reached.
8/4/2019 Working in Hot Environments
42/108
30
2. Environmental measures of heat exposureEnvironmental measures are generally based on air
temperature and relative humidity but do not take intoaccount the effect of radiant heat and air movement inthe workplace. Therefore, such measures cannot be usedto determine occupational heat stress in the industry.
Two commonly used environmental measures are:
1. The Humidex; and,
2. The Heat Index.
The Humidex
Environment Canadas Weather Service uses thehumidex as a measure of how hot people feel in outdoorenvironmental conditions. The humidex gives a
combined effect of air temperature and relativehumidity as a single number that is intended to reflectperceived heat (see Appendix B). Humidex levels canbe obtained on the Environment Canada website:http://www.weatheroffice.ec.gc.ca/canada_e.html.
Heat Index
The US National Weather Service has developed aHeat Index Chart to express perceived heat for differentenvironmental conditions of temperature and humidity.A heat index chart is available from the NationalWeather Service (NWS), the US National Oceanicand Atmospheric Administration (NOAA).Website:http://www.srh.noaa.gov/lzk/images/hindex1.gif.
8/4/2019 Working in Hot Environments
43/108
Section 5
Heat Exposure Standardsand Guidelines.
1. Occupational exposure limits.
2. Thermal comfort guidelines for offices.
8/4/2019 Working in Hot Environments
44/108
32
1. Occupational exposure limitsThe purpose of occupational exposure limits is to
eliminate or minimize the risk of heat-related illnesses.Exposure limits are set by provincial, territorial andfederal jurisdictions responsible for workplace healthand safety. Many regulatory agencies use the exposureguidelines recommended by the American Conferenceof Governmental Industrial Hygienists (ACGIH). Forfurther details please refer to the most recent version
of the ACGIH publication Threshold Limit Valuesfor Chemical Substances and Physical Agents &Biological Exposure Indices. The occupationalexposure limits are generally given as work/restregimen for working in hot environments.
An Example of Heat Stress Exposure Limits
Saskatchewan (Canada) Hot Conditions Guidelinesand Saskatchewan Labour publication "http://www.labour.gov.sk.ca/safety/thermal/hot/index.htm"Working Under Hot Conditions recommend thefollowing rest break schedule for working in hotenvironments. For exposure limits applicable to yourworkplace, please consult your health and safety
regulations.
8/4/2019 Working in Hot Environments
45/108
33
Sources: "http://www.labour.gov.sk.ca/safety/thermal/hot/page%208%20.htm"http://www.labour.gov.sk.ca/safety/thermal/hot/page%208%20.htm, and"http://www.worksafesask.ca/topics/specific_hazards/physical/heat.html"http://www.worksafesask.ca/topics/specific_hazards/physical/heat.html
Recommended
RestBreakSche
dulesforAcclimatizedWorkers
WetBulbGlobeTempe
rature(WBGT)Index
Heavy
Moderate
Light
Continuo
us
work
upto25.
0C
upto27.
0C
upto30.
0C
15
minutes
restperh
our
25.0
C
to2
6.0
C
27.0
C
to2
8.0
C
30.0
C
to3
0.
6C
30
minutes
restperhour
26.
0C
to28
.0C
28.
0C
to29
.0C
30.
6C
to31
.4C
45
minutes
restperhour
28.0
C
to30
.0C
29.0
C
to31
.0C
31.
4C
to32
.2C
WorkLoad
WorkRate
8/4/2019 Working in Hot Environments
46/108
34
Notes and definitions for the above table
The WBGT index in the above tables is based on
American Conference of Governmental IndustrialHygienists (ACGIH) TLV Documentation.
These indices are not equivalent to regular thermometerreadings. The tables apply only to acclimatized workerswithout special needs who are wearing lightweight, lightcoloured, loose-fitting cotton clothing. Adjustments mustbe made to these indices for workers with special needs.
Heavy work Intermittent lifting, pushing orpulling (such as pick and shovel work) or hardsustained work, such as assembly line activitieswhere workers are paced by machines andcannot stop.
Moderate work (1) Work done in a sitting posi-
tion, but requiring heavy arm and leg motions; or(2) work done while standing and involving mod-erate work at a machine or bench; or (3) workdone while walking about and involving moderatelifting or pushing activities.
Light work Sitting or standing; work at amachine or bench that requires mostly arm work.
Continuous work Assumes that there are shortmorning and afternoon breaks and a longer lunchbreak in an eight hour day.
Rest breaks This includes all breaks, such asregular work breaks and unscheduled pauses duringwork. If rest breaks occur in an area that issignificantly cooler than the work position,
the WBGT is modified.
8/4/2019 Working in Hot Environments
47/108
35
Applying the Recommended Rest Break Schedule
The recommended rest break schedule applies to
workers who are fully acclimatized. New workers andworkers returning from more than two weeks vacationor sick leave should be allowed a week to acclimatize.Start with a short exposure to hot worktwenty percentof the time on the first day. Another twenty percentshould be added each day after that.
The recommended rest break schedule assumes that
the WBGT index of the resting place is the same orsimilar to that of the workplace. Where the WBGT ofthe work area is different from that of the rest area, atime weighted average should be used. The weightedaverage should not exceed a WBGT of 30C for lightwork, 27C for moderate work and 25C for heavywork for any one hour of continuous work. The
weighted average is determined by the equation:WBGT1 x t1 + WBGT2 x t2
_____________________ = weighted average
t1 + t2
Where:
WBGT1 is the work area index
WBGT2 is the rest area index
t1 is the time worked every hour
t2 is the length of the rest period every hour
8/4/2019 Working in Hot Environments
48/108
36
Special Situations
If a job requires specialized clothing such as heavy
coveralls, "turn out gear" for firefighters orchemical-resistant clothing, the WBGT index mustbe adjusted down. The WBGT index should also beadjusted down for special needs workers, such as:
persons over 40
the obese
alcohol abusers unconditioned or unacclimatized workers who are
likely more susceptible to heat stress disorders
In these situations, obtain advice from a competentperson or a physician if needed.
If a job requires heavy coveralls, the WBGT index must be adjusted down
8/4/2019 Working in Hot Environments
49/108
37
When WBGT Indices Exceed the Table Guidelines
Higher heat exposures than shown in the table should
only be permitted where: A competent person will determine the maximum
length of work exposure to extreme heat that issafe, based on past experience in similar conditions.
Each worker will pace the speed of work and willbe able to terminate any particular heat exposurebecause of strain or discomfort.
A doctor will determine the fitness of each workerfor work in extreme heat.
Workers will be watched by a trained supervisoror worker who can recognize signs of heat effects.
Appropriate protective clothing or equipment willbe provided to reduce the intensity of heat exposure.
An emergency plan will be in place to rescue andtreat workers who become ill.
8/4/2019 Working in Hot Environments
50/108
38
Canadian Regulations
The following table summarizes requirements for the
thermal conditions in the workplace.
ACGIH TLVs: Threshold Limit Values (TLVs) recommended by the AmericanConference of Governmental Industrial Hygienists (ACGIH). The ACGIH TLVbooklet is updated annually.
Wet Bulb Globe Temperature Index (WBGT)
ACGIH TLVs
ACGIH TLVs
Similar to ACGIH TLVs
Hot Conditions Guidelines in WBGT units
ACGIH TLVs
Heat Stress (Health and Safety Guidelines)
April 2003 ACGIH TLVs
Safety in mines: Occupational exposure limitsWBGT similar to ACGIH TLVs
ACGIH TLVs
ACGIH TLVs
ACGIH TLVs
ACGIH TLVs
Jurisdiction
Canada, Federal
British Columbia
Alberta
Saskatchewan
Manitoba
Ontario
Quebec
New Brunswick
Nova Scotia
Prince EdwardIsland
Newfoundland
Canadian Regulations
8/4/2019 Working in Hot Environments
51/108
39
The Occupational Health Clinics for Ontario Workers(OHCOW) has developed a simplified screening to assessworkplace heat stress using humidex as a measure of the
environmental heat. The following table summarizes theHumidex Based Heat Response Plan.
Source: http://www.ohcow.on.ca/menuweb/hhrplan.pdf.
Response
- supply water to workers on an as needed basis
- post Heat Stress Alert notice.
- encourage workers to drink extra water.
- start recording hourly temperature andrelative humidity.
- post Heat Stress Warning notice.
- notify workers that they are drinking extra water.
- ensure workers are trained to recognize symptoms.
- provide 15 minutes relief per hour.
- provide adequate cool (1015C) water, at least 1cup (240 mL) of water every 20 minutes.
- workers with symptoms should seek
medical attention.
- provide 30 minutes relief per hour in addition to theprovisions listed previously.
- if feasible provide 45 minutes relief per hour inaddition to the provisions listed above.
- if a 75% relief period is not feasible then stop work
until the Humidex is 42C or less.
- stop work until the Humidex is 44C or less
Humidex
25-29C
30-33C
34-37C
38-39C
40-42C
43-44C
45C or over
Humidex Based Heat Response Plan
8/4/2019 Working in Hot Environments
52/108
40
2. Thermal comfort guidelines for officesThe occupational heat exposure limits are not applicable
to office work. There are no regulations specific tooffice work. However, there are guidelines for thermalcomfort in offices.
The following table shows the temperature and relativehumidity ranges recommended by the CanadianStandard Association's Standard CAN/CSA Z412-00 -"Office Ergonomics.
% Relative Humidity
50%
50%
Heating Season
Cooling Season
Temperature
2023.5C6875F
2326C7379F
Temperature and Humidity of an OfficeEnvironment taken from CSA Z412-00
8/4/2019 Working in Hot Environments
53/108
Section 6
Control Measures
1. Engineering Controls
2. Administrative Controls
3. Personal Protective Equipment
4. Sample Safe Work Practices
8/4/2019 Working in Hot Environments
54/108
42
1. Engineering ControlsEngineering controls are the most effective means of
reducing heat exposure in industrial work environments.Following are some examples of commonly usedengineering controls:
Automation and mechanization of tasks
Automation and mechanization of tasks reduces the need
for heavy physical work. Reducing heavy physical effortreduces the inner body heat production rate, and hence,the risk of heat stress.
Use of mechanical aids
Mechanical aids such as carts, turn tables, etc. reducethe amount of physical effort needed to perform a task
and hence reduce metabolic heat production.
Location of work stations away from hot objectsand processes
Increasing distance from hot surfaces reduces radiantheat exposure.
Insulating hot surfaces
Insulation reduces the surface temperature of aradiant heat source and hence reduces the radiantheat exposure of workers.
8/4/2019 Working in Hot Environments
55/108
43
Shielding
Shields stop radiated heat from reaching the worker.
Two types of shields can be used. Shields that reflect heat: Stainless steel, aluminum
or other bright metal surfaces reflect heat backtowards the source.
Shields that absorb heat: Absorbent shields, suchas water-cooled jackets made of black-surfacedaluminum, can absorb heat.
Ventilation and air conditioning
Ventilation, localized air conditioning and cooled observationbooths are commonly used to provide cool work stations.Cooled observation booths allow workers to cool down afterbrief periods of intense heat exposure while still allowing
them to monitor equipment.
Using local exhausts
Local exhaust systems remove the hot air and steamproduced by a process before it mixes with the ambientair in the work area.
Reducing the relative humidity
Air conditioning, dehumidification, and elimination ofopen hot water baths, drains, and leaky steam valveshelp reduce relative humidity.
Increasing air movement
If the air temperature is less than the skin temperature(35C or 95F), a fan can increase air movement. Briskair movement causes body cooling by convection andincreased sweat evaporation.
8/4/2019 Working in Hot Environments
56/108
44
Using fans to cool off
Fans don't cool the air they just move air around. Fans
keep you cool by increasing the rate of sweat evaporation.Following are some helpful tips for using fans.
USE your fan in or next to a window, box fans arethe best.
USE a fan to bring cool air in from outside.
USE your fan by plugging it directly into the wall outlet.
If you need an extension cord, it should be CSAapproved and should not present a trip hazard.
DO NOT use fans if the room is closed and filled withhot air. Blowing hot air on the body will increase therisk of adverse health effects.
DO NOT use a fan to blow extremely hot air on yourself.
This can cause heat exhaustion to happen faster.
8/4/2019 Working in Hot Environments
57/108
45
2. Administrative ControlsThe purpose of administrative controls is to minimize
heat stress risks by controlling work schedules, worklocations and work procedures. Administrative controlsinclude the following:
Acclimatization
Safe work practices
Training
Exposure time reduction
Prevention strategies for workers
Acclimatization
Acclimatization is the most important administrativecontrol. The concept of acclimatization is based on the
fact that the longer people work in hot environments, themore tolerant they become. People who are not used toworking in hot environments should be given a week ortwo to get acclimatized to the heat. Some individualsmay need longer than others. Also, persons with poorhealth may need more time to acclimate.
Helpful tips for the acclimatization of employees:ACCLIMATIZE new employees before assigning a full
workload. It is advisable to assign about half of thenormal workload to a new employee on the first dayof work and gradually increase on subsequent days.
INCREASE the duration of work gradually when a
new or transferred employee starts working in a hotenvironment.
INCREASE the level of physical activity gradually start with light work on the first day and graduallyincrease the work-load on subsequent days.
MONITOR heat strain symptoms during the acclimati-
zation period. If an individual shows symptoms ofexcessive strain, reduce the duration of exposureand/or the level of activity.
8/4/2019 Working in Hot Environments
58/108
46
ADVISE employees who are on medication to consulttheir doctor and inquire if the medication will affecttheir heat tolerance ability.
Loss of acclimatization
Loss of acclimatization occurs gradually when a personis moved permanently away from a hot environmentor after several days of absence from work.
Safe Work PracticesREDUCE physical effort needed for performing a task.
PROVIDE an appropriate work-rest regimen asrecommended in the health and safety legislation.The American Conference of GovernmentalIndustrial Hygienists (ACGIH) has recommended a
work-rest regimen which can be found in the currentversion of the ACGIH publication Threshold Limits(TLVs) for Chemical Substances and PhysicalAgents & Biological Exposure Indices.
SCHEDULE jobs to minimize heat stress.
SCHEDULE outdoor jobs so that people perform
physically demanding jobs during cooler periods ofthe day.
PAY attention to employees with special needs.Advise and encourage pregnant workers and workerswith a medical condition to discuss any limitationsand special precautions needed for working in hotenvironments with their doctor.
PROVIDE appropriate training and education toenable employees to:
Develop a high degree of awareness about thepotential hazards of working in hot environments;and
Ways of preventing adverse health effects due tosuch hazards.
8/4/2019 Working in Hot Environments
59/108
47
Provide appropriate training and education
A training program should include the following topics:
Employers responsibilities in providing a safeworkplace and establishing safe work practices;
Hazards and potential health effects of heat stress;
Use of WBGT monitor and interpretation of results;
Principles of work-rest regimen design;
Predisposing factors, danger signs and symptomsof heat-related illnesses;
First-aid procedures for heat-related disorders;
Possible side effects of certain medications whentaken in a hot environments;
Proper use and maintenance of protective clothingand equipment.
8/4/2019 Working in Hot Environments
60/108
48
ALLOW adequate recovery time. Provide adequate restperiods to reduce the risk of adverse health effects.
USE the Buddy System. In hot working environmentsthe buddy system is a must. Individuals are lesslikely to notice their own symptoms. The survival ofthe affected person depends on the co-workersability to recognize the symptoms and seek timelymedical help.
MINIMIZE metabolic heat production by:
Reducing work pace;
Reducing work duration;
Reducing the physical exertion required to per-form a task;
Increasing the frequency and duration of rest
breaks; Substituting light tasks for heavy ones;
Increasing assigned staff so that more workersshare the workload;
Reducing the use of heat generating devices; and,
Reducing the time and frequency of working with
or near heat sources.
Prevention Strategies for Workers
In hot environments, workers can use certain preventivestrategies to minimize the risk of adverse health effects.Such strategies include:
REPORT discomfort and early symptoms of heat-relatedillnesses to your supervisor.
DRINK plenty of water even if you do not feel thirsty.Sweating results in the loss of body fluids. Excessivewater loss may cause dehydration. Thirst is not areliable indication of bodys need for fluid replace-
ment. A person should drink approximately 250millilitres (one cup) of cool water every 20 minutes.Coffee, sweet beverages and alcohol must be avoided.
8/4/2019 Working in Hot Environments
61/108
49
MAINTAIN a healthy diet. On hot days, eat lightfoods such as fruits and vegetables, and avoid heavyfoods such as proteins which increase body heat.
LIMIT non-work heat stress exposures.
REPORT any changes in health status to yoursupervisor. Pregnant workers and those with medicalconditions should consult their physician about theiroccupational exposures to heat stress. Older workersshould be particularly cautious due to a decreased
ability to sweat.
CONSULT your doctor if you are taking medicationsthat may cause heat intolerance or inhibited sweat-ing. Certain antibiotics will cause photosensitivity.People taking such drugs should avoid strongmid-day sunlight.
Alcohol Consumption increases the risk of heart related illness
8/4/2019 Working in Hot Environments
62/108
50
3. Personal ProtectionEngineering controls are the most desirable method
of controlling heat exposure. Personal protectiveequipment (PPE) should be used as an interim measurewhile engineering controls are being explored.
Eye protection
Eye protection that absorbs infrared radiation (heat
rays), may be needed when working near very hotobjects, such as molten metals and red-hot objects.
Clothing
Ordinary clothing provides someprotection from heat radiated bysurrounding hot surfaces. Light
clothing allows maximum skinexposure and efficient bodycooling by sweat evaporation.
Cotton clothing is cooler thanpolyester clothing. However, cottonwill absorb water and wet clothing
tends to be uncomfortable.When selecting clothing,heat stress prevention should bebalanced with other health andsafety risks. For example, foroutdoor workers, a balance mustbe achieved between heat stress
prevention and the ultravioletexposure.
Cooling Vest
8/4/2019 Working in Hot Environments
63/108
51
Impermeable clothing
Work that requires the use of impermeable clothing
presents an added heat burden. Impermeable clothingreduces the body's ability to dissipate heat. Therefore,it is necessary to provide a cooler working environ-ment than that recommended for workers wearinglight clothing.
Protective clothing
The selection of protective clothing depends on thespecific circumstance. Working in certain hotenvironments may require insulated gloves, insulatedsuits, reflective clothing, infrared-reflecting face shieldsand safety footwear (e.g., foundry boots, welder's boots).For extremely hot conditions, thermally conditionedclothing is available. Examples of such protective
clothing are:
A self-contained air conditioner in a backpack.
A compressed air source which feeds cool air intothe jacket or coveralls through a vortex tube.
A jacket which has pockets that can be filled withcontainers of ice.
Check with your local safety equipment supplierregarding the types of personal protective equipmentavailable and the degree of protection such clothing isexpected to provide.
In a high radiant heat situation, people generally usereflective clothing. However, this advantage may benullified if the clothes interfere with the sweatevaporation. For very hot environments air, wateror ice-cooled insulated clothing may be used.
Workers who move back and forth between very hot,dry indoor environments and cold, winter outdoorenvironments find that long underwear moderates
the extremes in temperatures.
8/4/2019 Working in Hot Environments
64/108
52
Method of Control
Reduce body heat production
Stop exposure to radiated heatfrom hot objects
Reduce convective heat gain
Increase ventilation
Clothing
Acclimatization
Duration of work
Rest area
Water
Pace of work
First aid and medical care
Action
Mechanize tasks
Insulate hot surfaces. Use reflectiveshields, aprons, remote controls
Lower air temperature. Increase air speedif air temperature below 35C. Increaseventilation. Provide cool observationbooths
Reduce humidity. Use a fan to increase airspeed (movement)
Wear loose clothing that permits sweat
evaporation but stops radiant heat. Usecooled protective clothing for extremeconditions
Allow sufficient acclimatization period fornew workers
Shorten exposure time and use frequentrest breaks
Provide cool (air-conditioned) rest-areas
Provide cool drinking water
If practical, allow workers to set their ownpace of work
Establish emergency procedures. Assignone person trained in first aid to eachwork shift. Train workers in recognition
of signs and symptoms of heat stroke
Table 3 - Summary of Heat Stress Control Measures
Engineering controls
Administrative controls
8/4/2019 Working in Hot Environments
65/108
53
4. Sample safe work practicesThe following are some examples of safe work practices
for preventing heat stress.
(a) Working outdoors during prolonged heat spells
In the summer months, outdoor workers are simultane-ously exposed to two main health hazards:
i. Heat stress as air temperature and/or humidity
increases; and,
ii. UV rays from sunlight.
Preventing health effects of heat Stress
AVOID unnecessary or unusual stressful activity.
PERFORM stressful tasks during the cooler parts of
the day (early morning or at night).
AVOID double shifts and overtime whenever possible.Employers must not permit double shift or overtimeto workers in hot environments.
ADOPT a recommended work-rest regimen to recoverfrom the heat stress.
DRINK plenty of water in frequent small portions.Employers are required to provide plenty of drinkingwater in hot workplaces.
AVOID alcohol consumption. The consumption ofalcoholic drinks increases the risk of dehydrationand other heat-related illnesses.
CONSULT your doctor about potential side effects ifyou are taking blood pressure control medication,diuretics or water pills.
TAKE sufficient sleep and good nutrition for maintaininga high level of heat tolerance.
8/4/2019 Working in Hot Environments
66/108
54
Preventing health effects of UV exposure
During outdoor work, the safety measures for UVprotection depend on the intensity of UV rays in
the sunlight.
The weather service of Environment Canada expressesthe intensity of UV rays in the units of UV index.The UV index is the highest during noon hours inthe summer months and lowest in the mornings andevenings of winter days. Appendix C gives safety tips
for different levels of UV index.
(b) Working near extremely hot objects
People who work near extremely hot objects are at ahigh risk of heat stress. The main source of heatexposure is radiant heat from hot surfaces such asfurnaces and molten metals. Examples of suchworkplaces include:
Iron, steel and nonferrous foundries
Brick-firing and ceramics operations
Glass products manufacturing plants
Rubber products manufacturing plants
Bakeries Restaurant kitchens
Smelters
You must pay special attention if:
You are unacclimatized;
You have a history of heat intolerance; You are recovering from a fever;
You are dehydrated;
You have circulatory disorders;
You are taking medication; or,
You are in overall poor health.
8/4/2019 Working in Hot Environments
67/108
Basic Safety tips
PROVIDE adequate ventilation and air movement.
INSTALL shields to reduce radiant heat exposurefrom hot surfaces.
PROVIDE cool work stations.
PROVIDE adequate protective clothing and equipmentincluding gloves, safety footwear and eye protection.When selecting protective clothing, consider the
following important factors:
Protection from radiant heat; and
Allowance for sweat evaporation.
ENSURE that all new and transferred employees areacclimatized before assigning them a full work-load.
Acclimatization may also be needed for employeeswho return to work after several days of vacation.
PLAN job rotation to reduce duration of heat exposure.
PROVIDE cool drinking water and make sure thatemployees understand the importance of drinkingwater at frequent intervals.
PROVIDE adequate rest breaks. Work-rest periodsrecommended in the ACGIH TLV bookletmay be used as a guideline todevelop a company policy.
Drink plenty of water
55
8/4/2019 Working in Hot Environments
68/108
Hands free water system provides ready access to drinking water
Hands FreeDelivery Tube
Two-LiterResevoir
Harness
56
8/4/2019 Working in Hot Environments
69/108
Section 7
Occupational Health andSafety Legislation
1. Canadian Legislation
2. US Legislation
8/4/2019 Working in Hot Environments
70/108
58
1. Canadian LegislationThe purpose of Occupational Health and Safety
(OH&S) legislation is to protect you, the employee,against any hazards on the job. The occupationalhealth and safety act outlines the rights andresponsibilities of employers, supervisors andemployees in ensuring workplace health and safety.
The Canadian health and safety legislation is basedon the internal responsibility system. In this system,
everyone in the workplace is responsible for healthand safety. Employers have legal responsibility toprovide a safe workplace and ensure that work iscarried out in a safe manner.
Employers responsibilities
Employers must provide a safe workplace to preventrisk of injury and illness. Therefore, it is the employersresponsibility to protect employees from harmfulheat exposure.
In some Canadian jurisdictions, there are no regula-tions with respect to heat stress. However, the generalduty clause in the health and safety act holds theemployer responsible for the overall health and safetyof employees. Therefore, employers are responsiblefor implementing an adequate heat stress preventionprogram.
8/4/2019 Working in Hot Environments
71/108
59
Employee responsibilities
In general, employees must take all reasonable and
necessary precautions to ensure their own health andsafety and that of other employees and any personswho might be affected by their activities. Followingare some examples of employee responsibilities:
Follow safe work practices established bythe employer.
Use safety equipment required by the employer.
Report any unsafe conditions or practices tothe employer.
Report every accident or incident (near miss).
Employees Rights
Employees have the following three basic rights:
Right to know: The employer must provide informationabout any actual or potential hazards, and trainemployees in safe work practices.
Right to participate: Employees have the right toparticipate in workplace health and safety activitiesthrough health and safety committees or an employee
health and safety representative.
Right to refuse unsafe work: Employees have theright to refuse performing work that poses a danger totheir health and safety. Health and safety legislationoutlines procedures to be followed in resolving workrefusals. The following chart summarizes steps
involved in resolution of work refusals. Please consultyour appropriate health and safety act for details. Thesteps involved in the resolution process may vary fromone jurisdiction to another.
In Ontario, certified members of the health and safetycommittee have the right to stop work following theprocedure outlined in the Ontario Health and Safety Act.
8/4/2019 Working in Hot Environments
72/108
60
Work Refusal Chart
Supervisor
Union/H&S Rep
H&S Comm. Member
Investigate
UNRESOLVED
UNRESOLVED
BACK TO WORK
RESOLVED
Call GovernmentInspector
Assign reasonablealternative work
Assign work beingrefused to another
worker
Decision of theInspector
Further GovernmentAction
Further EmployerAction or Appeal of
Government Directives
Supervisor and Workerattempt to resolve
problem
Worker OH&S Concern(Work Refusal)
Reports to Supervisor
RESOLVED
RESOLVED
RESOLVED
8/4/2019 Working in Hot Environments
73/108
61
2. U.S. LegislationIn the United States of America (USA) the
Occupational Safety and Health Act is popularlyknown as the OSH Act. The Occupational Safety andHealth Administration (OSHA) is responsible foradministering the OSH Act.
The OSH Act does not cover the following fourcategories of employees:
Self-employed persons; Farms which employ only immediate family
members of the farm employer;
Workers covered by other legislation; and
State and local government employees.
Regulations dealing with OSHA are published in Title29 of the Code of Federal Regulations as:
29 CFR Part 1910 Occupational Safety and HealthStandards; and
29 CFR Part 1926, Construction Standards.
These standards define exposure limits, exposure
monitoring methods, medical surveillance andprotective measures.
Duties of Employer
The OSH Act sets out two main duties for employers:
Employers must provide a workplace which is freefrom hazards that are known to cause of likely tocause death or serious physical harm to employees.
Employers must comply with occupational safetyand health standards under the Act.
8/4/2019 Working in Hot Environments
74/108
62
Duties of Employees
Employees must comply with occupational safety and
health standards, rules, regulations and orders whichare applicable to their own conduct and actions.
Key Provisions
Some key provisions of the OSH Act:
To assure, insofar as possible, that every employee
has safe and healthy working conditions. To require employers to maintain accurate records
of exposures to potentially toxic materials orharmful physical agents and inform employeesof the monitoring results.
To allow at least one employee representative tobe present during the walkaround inspection.
To encourage free and open exchange of informa-tion between employees and the inspector.
To implement procedures for investigating allegedviolations, at the request of any employee oremployee representatives, issuing citations andassessing monetary penalties against employers.
8/4/2019 Working in Hot Environments
75/108
Section 8
Information Sources
1. Canadian Government Departments withResponsibility for Occupational Healthand Safety
2. US Federal Safety and Health Agencies
8/4/2019 Working in Hot Environments
76/108
64
1. Canadian Government DepartmentsResponsible for Occupational
Health and Safety
Canadian Centre for OccupationalHealth and Safety (CCOHS)
Inquiries & Client Services(free answers to your OH&S questions)135 Hunter Street EastHamilton, ON L8N 1M5Phone: 905-570-8094(8:30 AM to 5:00 PM EST Time)Toll-free: 1-800-668-4284 (Canada and US only)
Fax: 905-572-4500E-mail: [email protected] Answers Web Site: www.ccohs.ca/oshanswersWeb Site: www.ccohs.ca
General ContactPhone: 905-572-2981
Fax: 905-572-2206
Federal Jurisdiction
Workplace Health and SafetyHuman Resources and Social Development Canada
1-800-641-4049Ottawa ON K1A 0J2
Web Site: http://www.hrsdc.gc.ca/en/labour/workplace_health/index.shtml
Regional and District Offices:Web Site: http://www1.servicecanada.gc.ca/en/
gateways/where_you_live/menu.shtml
8/4/2019 Working in Hot Environments
77/108
65
Provincial Jurisdictions
AlbertaWorkplace Health and SafetyAlberta Employment, Immigration and Industry
10030-107 StreetEdmonton, AB T5J 3E4(Edmonton and surrounding area)Phone: (780) 415-8690Toll-free in Alberta: 1-866-415-8690
Fax: (780) 422-3730E-mail: [email protected] Site: http://employment.alberta.ca/cps/
rde/xchg/hre/hs.xsl/53.html
British ColumbiaWorkSafeBC (Workers' Compensation Board
of British Columbia)6951 Westminster Highway (Richmond, BC)PO Box 5350 Stn TerminalVancouver, BC V6B 5L5Workplace Safety and Health InquiriesPhone: (604) 276-3100Toll-free in B.C.: 1-888-621-7233 (SAFE)
Fax: (604) 244-6490Emergency and Accident ReportingToll-free in B.C.: 1-888-621-7233 (SAFE)After hours: 1-866-922-4357 (WCB-HELP)Web Site: www.worksafebc.com
Manitoba
Workplace Safety and Health DivisionManitoba Labour and Immigration
200-401 York AvenueWinnipeg, MB R3C 0P8General Inquiries: (204) 945-3446Toll free in Manitoba: 1-800-282-8069After hours: (204) 945-0581Fax: (204) 945-4556E-mail: [email protected] Site: www.gov.mb.ca/labour/safety/
8/4/2019 Working in Hot Environments
78/108
66
New BrunswickWorkplace Health, Safety and CompensationCommission of New Brunswick
1 Portland StreetPO Box 160Saint John, NB E2L 3X9Phone: (506) 632-2200Toll free: 1-800-222-9775Fax: (506) 642-0718E-mail: [email protected] Site: www.whscc.nb.ca
Newfoundland and LabradorOccupational Health and Safety BranchDepartment of Government Services
15 Dundee AvenueMount Pearl, NL A1N 4R6General Inquiries: (709) 729-2706Toll-free in NL: 1-800-563-5471Fax: (709) 729-3445Serious Workplace Accident ReportsPhone: (709) 729-4444 (24 Hours)Web Site: www.gs.gov.nl.ca/ohs/
Northwest Territories and NunavutWorkers' Safety and Compensation Commissionof Northwest Territories and Nunavut
PO Box 8888Yellowknife, NT X1A 2R3
General Inquiries: (867) 920-3888Toll free: 1-800-661-0792Fax: (867) 873-4596Toll Free Fax: 1-866-277-3677E-mail: [email protected] Site: www.wcb.nt.ca
8/4/2019 Working in Hot Environments
79/108
67
IqaluitPO Box 669Iqaluit, NU X0A 0H0Phone: (867) 979-8500Fax: (867) 979-8501Toll-free: 1-877-404-4407Toll Free Fax: 1-866-979-8501E-mail: [email protected]: www.wcb.nt.ca
Nova ScotiaOccupational Health and Safety Division Nova ScotiaDepartment of Environment and Labour andWorkforce Development
5151 Terminal Rd., 6th FloorPO Box 697
Halifax, NS B3J 2T8General Inquiries: (902) 424-5400Toll free in NS: 1-800-952-2687Fax: (902) 424-5640E-mail: [email protected] Site: http://www.gov.ns.ca/enla/ohs/
OntarioMinistry of LabourOccupational Health and Safety Branch
505 University Avenue, 19th FloorToronto ON M7A 1T7416-326-3835Fax 416-326-7761
1-800-268-8013 (province-wide)E-mail: [email protected] Site: www.labour.gov.on.ca/english/hs/index.html
8/4/2019 Working in Hot Environments
80/108
68
Prince Edward IslandWorkers Compensation Board of PEIOccupational Health and Safety
PO Box 757, 14 Weymouth StreetCharlottetown, PE C1A 7L7General Inquiries: (902) 368-5680Toll-free (in Atlantic Canada): 1-800-237-5049Occupational Health & Safety24 Hr Emergency Tel: (902) 628-7513Customer Liaison Service: 1-866-460-3074
Fax: (902) 368-5705Web Site: www.wcb.pe.ca
QubecCommission de la sant et de la scurit du travaildu Qubec (CSST) (Occupational Health & Safety
Commission)1199, rue de BleuryC.P. 6056, Succursale centre-villeMontral QC H3C 4E1Tel: 514-906-3780/514 906-3061, poste 2214
1-866-302-2778Fax: 514-906-3781/514 906-3016
www.csst.qc.ca(514) 906-2911 Urgence 24 h Services deprvention-inspectionWeb Site: http://www.csst.qc.ca/portail/fr/
SaskatchewanAdvanced Education, Employment and LabourOccupational Health and Safety Division
400 - 1870 Albert StreetRegina, SK S4P 4W1Phone: (306) 787-4496Toll-free in SK: 1-800-567-7233Fax: (306) 787-2208Web Site: www.labour.gov.sk.ca/
8/4/2019 Working in Hot Environments
81/108
69
Saskatoon Office:122-3rd Avenue NorthSaskatoon, SK S7K 2H6
Phone: (306) 933-5052Toll-free: 1-800-667-5023Fax: (306) 933-7339
Yukon TerritoryYukon Workers' Compensation, Health and Safety
Board Occupational Health and Safety Branch401 Strickland StreetWhitehorse, YT Y1A 5N8General Inquiries: (867) 667-564524-hour Emergency Line for Reporting SeriousWorkplace Accidents and Injuries: (867) 667-5450Toll free across Canada: 1-800-661-0443Fax: (867) 393-6279E-mail: [email protected] Site: www.wcb.yk.ca
For an up-to-date listing of information sources visithttp://www.ccohs.ca/oshanswers/information/govt.html
8/4/2019 Working in Hot Environments
82/108
70
2. US Federal Safety and HealthAgencies
US Environmental Protection Agency (EPA)Ariel Rios Building1200 Pennsylvania Avenue NW,Washington, DC 20460Phone: (202) 272-0167Web Site: www.epa.gov
National Institute for Occupational Safetyand Health (NIOSH)
Education and Information Division (EID)4676 Columbia Parkway
Cincinnati, OH 452261-800-CDC-INFO (1-800-232-4636)Outside the US: (513) 533-8328Fax: 1-513-533-8347E-mail: [email protected] Site: www.cdc.gov/NIOSH/
Occupational Safety & Health Administration(OSHA)200 Constitution Ave., NWWashington, DC 20210Phone: (202) 693-2000Emergency reporting or if you have workplace safety
and health related questions
Toll Free: 1-800-321-OSHA (6742)Web Site: www.osha.gov
8/4/2019 Working in Hot Environments
83/108
Section 9
Bibliography andInternet Links
8/4/2019 Working in Hot Environments
84/108
72
A Guide to Heat Stress in Agriculture (summary).OSHA/EPA guide (1993, May).
Environment Canada Fact Sheet: Summer
Severe Weatherhttp://www.mb.ec.gc.ca/air/summersevere/index.en.html
Environment Canada Humidex Calculatorhttp://lavoieverte.qc.ec.gc.ca/meteo/Documentation/Humidex_e.html
Environment Canada Weather Office
http://www.weatheroffice.ec.gc.ca/canada_e.htmlProvince of Ontario Heat Stress Guideline
http://www.labour.gov.on.ca/english/hs/guidelines/gl_heat.html
US Dept. of Labour Heat Stresshttp://www.osha.gov/SLTC/heatstress/
OSHA Heat Stress Cardhttp://www.cdc.gov/niosh/topics/heatstress/
Extreme Heathttp://emergency.cdc.gov/disasters/extremeheat/index.asp
FEMA Federal Emergency Management AgencyExtreme Heathttp://www.fema.gov/hazard/heat/index.shtm
The Australian Council of Trade Unions ACTUGuidelines for Working in Seasonal Heathttp://www.actu.asn.au/Archive/Papers/ACTUGuidelinesForWorkingInSeasonalHeat.aspx
Prevent Heat Stresshttp://www.wsib.on.ca/wsib/wsibsite.nsf/public/PreventHeatStress
Heat Stress in Constructionhttp://www.cpwr.com/search.php?zoom_query=heat+stress&zoom_per_page=100&zoom_and=0&zoom_sort=0
OR-OSHA: The Heat Equationshttp://www.cbs.state.or.us/external/osha/pdf/pubs/3333.pdf
Working Outdoors Factsheethttp://www.twcc.state.tx.us/information/videoresources//s_working_outdoorspdf
8/4/2019 Working in Hot Environments
85/108
Ultra violet radiation from the sunhttp://www.cdc.gov/elcosh/docs/d0100/d000146/D000146.html
Hot Environments Health Effectshttp://www.ccohs.ca/oshanswers/phys_agents/heat_health.html
Hot Environments Control Measureshttp://www.ccohs.ca/oshanswers/phys_agents/heat_control.html
US Department of Labour Confined space
Hazardshttp://www.osha.gov/SLTC/smallbusiness/sec12.html: This document on confined space hazards has asection on thermal hazards.
MNOSHA heat-stress guidehttp://www.doli.state.mn.us/heatstrs.html
1. CDC. Illness and death due to environmentalheat--Georgia and St. Louis, Missouri, 1983.MMWR 1984;33:325-6.
2. Ramsey JD, Burford CL, Beshir MY, Hensen RC.Effects of workplace thermal conditions on safework behavior. Journal of Safety Research1983;14:105-14.
3. State of California, Department of Health,Occupational Health Branch. Occupational diseasein California. Annual Reports 1973-1976.
4. Dukes-Dobos FN. Hazards of heat exposure. Areview. Scand J Work Environ Health 1981;7:73-83.
5. Bartley JD. Heat stroke: is total prevention possible?Milit Med 1977;142:528,533-5.
6. World Health Organization. Health factors involvedin working under conditions of heat stress.WHO Technical Report Series 1969; no. 412.
7. Criteria for a recommended Standar; OccupationalExposure to Hot Environments, National Institutefor Occupational Safety and Health. DHHS(NIOSH) publication No. 72-10269, 1972
73
8/4/2019 Working in Hot Environments
86/108
74
8/4/2019 Working in Hot Environments
87/108
Section 10
Appendices
A. A summary of health hazards andpreventive measures
B. The Humidex
C. Safety tips for different levels of theUV index
D. Glossary
E. Abbreviations
F. Sample heat stress policy and checklist
G. Case histories: fatalities from occupationalheat exposure
8/4/2019 Working in Hot Environments
88/108
APPENDIX AA summary of health hazards and preventive measures.
Type of work
Working nearextremely hot
objects such asfoundries,furnaces, red hotmetals, bakeryovens
Working outdoorson hot summerdays such asconstructionwork, road repair,farming andgrounds keeping
Health andSafety Concerns
Heat-related illnesses andheat stroke due to:
1. Radiant heat emissionfrom hot objects
2. Temperature andhumidity of the workingenvironment
3. Dehydration due toexcessive sweating
4. Excessive inner bodyheat production due toheavy workload
5. Risk of cataracts due toinfrared radiationexposure of the eyes
1. Radiant heat fromthe sun
2. Hot environmentaltemperature and relativehumidity
3. Heavy work load
Risk of skin cancer and
eye disorders due to UV(sunlight) exposure
Prevention
Reduce radiant heat emissionfrom hot objects by shieldingthe object
Reduce heat reaching theworker by using adequateshielding
Provide cool air
Provide plenty of drinkingwater
Use mechanical aids toreduce physical exertion
Provide appropriate eyeprotection
Wear wide brim hats, fullsleeve shirts and long pants
Wear loose cotton clothing
Drink plenty of water atfrequent intervals
Perform heavy work duringcooler parts of the day.
Avoid skin and eyeexposure to direct sunlightby using wide brim hats,full sleeve shirts and longpants
Sunglasses with UVprotection
Sun blocking cream withat least SPF 15
Health Hazards and Preventive Measures
74
8/4/2019 Working in Hot Environments
89/108
APPENDIX B
The HumidexThe Weather Service of Environment Canada uses thehumidex to provide the public with a sense of how hotit feels when we are outdoors. At a given temperature,the humidex increases as relative humidity increases.
Environment Canada has provided the following
relationship between humidex and perceived heat:In addition to temperature and humidity, weatherconditions such as the amount of sunshine and windspeed will also affect the how hot a person feels.
Determining the Humidex
The following chart can be used to determine thehumidex. For example, if the temperature is 30Cand the relative humidity is 70%, the humidex is 41C.This is considered a level of great discomfort. For 50%relative humidity and 30C temperature, the humidex is36C, which is a condition of some discomfort.
75
8/4/2019 Working in Hot Environments
90/108
78
Source: Environment Canada: websitehttp://www.wul.qc.ec.gc.ca/metro/documentation/Humidex/humidex_a.html
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
20
21
2
2
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
29
3
1
33
35
37
39
41
43
45
48
50
53
55
58
28
3
0
32
34
36
38
40
42
44
47
49
51
54
56
59
28
3
0
31
33
35
37
39
41
43
45
48
50
52
55
57
60
27
2
9
31
32
34
36
38
40
42
44
46
49
51
53
56
58
26
2
8
30
32
33
35
37
39
41
43
45
47
50
52
54
57
59
26
2
7
29
31
33
34
36
38
40
42
44
46
48
50
53
55
57
25
2
7
28
30
32
33
35
37
39
41
43
45
47
49
51
53
56
58
24
2
6
27
29
31
32
34
36
38
40
42
43
45
47
50
52
54
56
24
2
5
27
28
30
32
33
35
37
38
40
42
44
46
48
50
52
54
57
23
2
4
26
27
29
31
32
34
36
37
39
41
43
45
46
48
50
52
55
57
22
2
4
25
27
28
30
31
33
34
36
38
40
41
43
45
47
49
51
53
55
57
22
2
3
24
26
27
28
30
32
33
35
37
38
40
42
43
45
47
49
51
53
55
57
22
2
2
24
25
26
28
29
31
32
34
35
37
39
40
42
44
45
47
49
51
53
54
56
22
2
3
24
24
26
27
28
30
31
33
34
36
37
39
40
42
43
45
47
49
50
52
54
22
2
3
24
25
26
27
27
28
30
31
33
34
36
37
39
40
42
43
45
47
48
50
52
22
2
3
24
25
26
27
27
28
30
30
32
33
34
36
37
39
40
42
43
45
46
48
49
22
2
3
24
25
26