1
Xenocron Tuning Solutions
Client Dyno Tuning Agreement Last Updated 6/21/18
Please make sure you read, initial and understand everything on these pages. If you have questions, please
ask via phone or email before you come for your appointment, not after you arrive on the day of your tune. In
order for you to get the maximum benefit out of us tuning your car, we need to work together to make that
happen. I will expect (assume) that everything in this list is up to par unless prior arrangements are made and
possible issues are discussed before you come in for your tune. Please fill out all blank spots with the
information requested before arriving with your car and sign this form to signify that you have read it
completely and you agree to all terms. We do not perform any mechanical work like we outline here, we do not
have techs and we cannot look at your car and know this stuff is perfect. None of this is required, but it is
HIGHLY advised for your own good.
Arrival Time and Tune Start: ______ initial
All tuning appointments begin at your scheduled time, a confirmation email is sent to everyone
confirming the DATE and TIME. I expect that you arrive early or at least right on time so that we can get the
full amount of allotted time in for tuning your car. The clock starts at your scheduled time and most flat rate
tunes are scheduled to go for 3-4 hours max. If your vehicle is in 100% working order, we shouldn’t need any
more time for the full experience including setup, loading on the dyno, tuning, unloading, and final button up of
the car. If you arrive late for any reason, this will cut into the allotted time for tuning. I don’t want to have to
“rush” when tuning so please don’t put me in that situation. If the tune goes longer than the allotted time, it is
$150/hr that your car is on dyno and in my shop after the flat rate time cutoff. If you do not want to continue on
at this time, it is your responsibility to stop me and notify me that you are not willing to incur any additional
charges. We will of course discuss options at that point as I want to help you out to the best of my ability and
my ultimate goal is that you leave happy.
Payment: ______ initial
Payment is due in full up front before beginning your tune. This total is less any deposit you have paid
already and will need to be paid in cash only please. For instance, if you paid a $100 deposit for the
appointment and your flat rate tune price is $600, you will pay $500 in cash before the tune begins. Any parts,
labor or other charges incurred during the session will be tallied at the end of the tune and can be paid for with
cash, credit card or Paypal as needed. If you do not bring cash with you to your appointment, I will direct you
to the nearest ATM, and ask you to go there first before beginning the tune. This will of course most likely cut
into the allotted time for tuning and I really don’t want to have that happen so please plan ahead. All pricing is
online and current as well as included at the end of this agreement.
Running Vehicle: _______ initial
Any vehicle which arrives for its tuning appointment in a NON-RUNNING state will be charged an
automatic $100 surcharge. Vehicle must be able to start, run and drive into the dyno in order to be considered
ready for a Dyno Tune. If the battery is dead when you unload the car off of your trailer, this is the same
circumstance and you will be charged the same fee unless you bring your own jumper pack, get it started and
running and can drive it up to the dyno. A vehicle will not be loaded or strapped onto the dyno until it is in a
properly running state. Any labor needed to fix a vehicle to get it to run will be charged independently of the
tuning price if the customer is not able to perform the work themselves, with their own tools.
2
Please make sure the following items are completed prior to your tune date, and fill in the
information in the blank spots on this paper along with your intials. These are not
required but are for your best interest and to give the tuner the best information possible.
Parts List / Setup Details: ______ initial
It is always in the customer’s best interest to have a thorough and detailed understanding of all of the
parts in any setup and the details of the build. As a tuner, a lot of my job requires guessing and assuming, and
prefer to eliminate as many assumptions and make as few guesses as possible, so that I can tune your car more
effectively and safely and at the same time make the most power the setup can deliver. If you don’t know what
brands were used in your build, or the specs on the parts used in your setup, this makes it harder to do my job
since generally I am not the one who recommended which parts you should use or did the build myself. The
more you know, the less likely you are to be ripped off by a shop or builder that did some mechanical work for
you at the same time so PLEASE, get intimately acquainted with your parts list and build specs. For example,
if you have a 700 HP drag car built, I expect you to know what your piston to wall clearance was set at by your
machinist.
Compression Test:
In my opinion, you should know the health of your motor before having it tuned. I can be more
thorough when I know that compression is good before beginning a tune. Performing a tune on an unhealthy
motor is the quickest way to a disaster and a potential waste of other good parts that might be ruined in the
process. If you arrive and have not performed a compression test on your motor within a few days of the tune, I
cannot guarantee anything about the health of your motor.
Approximately ‘Healthy’ numbers –
8:1-8.5:1 compression: 150-170 psi per cylinder
8.5:1~9.5:1 compression: 170-210 psi per cylinder
9.5:1~11:1 compression: 210-250 psi per cylinder
11:1+ compression: 250+ per cylinder (highly depends on cams being used)
The tested numbers shouldn’t vary any more than 10% from cylinder to cylinder or this may indicate a
problem.
Results: Cylinder #1 ______ Cylinder #2 ______ Cylinder #3 ______ Cylinder #4 ______
Valve Adjustment
See the specs for your motor/cams from a Service Manual for what the valve lash should be set to on
your motor. Set the valves on a fully cold engine only as metal expands when heated which could throw off
your settings when performing a valve adjustment on a warm motor. Please write the settings you used when
adjusting your valve lash. Valve lash is VERY important if you want to make POWER, please don’t
overlook this as a non-essential piece of the build puzzle. Refer to a factory manual for actual factory specs or
your cam manufacturer…and my recommendation is always to set lash on the LOOSER side of the spectrum.
Intake Setting: ______ Exhaust Setting: ______ Date Performed: ________
3
Timing Belt/Chain and Base Timing ______ initial
The timing belt/chain, camshafts and crank need to all be synched correctly before coming in for your
scheduled tune. This is a fairly simple process on a stock motor and you can check your Service Manual for
procedures on how to perform this. Various motor combinations (Frankenstein motors with VTEC Heads on
Non-VTEC blocks) may affect exactly how you bring the motor into proper spec. Other things that may affect
timing will be block and head surfacing, adjustable cam gears set incorrectly, timing belt set on the wrong teeth
of the cam gear or incorrectly machined aftermarket cam gears, using the wrong parts for the combination put
together and more. Please consult a professional before your tune if you aren’t 100% sure that your timing is
set correctly. If timing is off, this will result in an additional charge for us to repair if easily possible.
Also check base timing with a timing light and make sure it is approximately in the 14-18 degree BTDC
(before top dead center) region. Adjust the distributor if this setting is way out of spec to see if you are able to
bring it within spec using only the distributor. If you can, chances are everything mechanically is set
correctly…if you cannot, then chances are something is set incorrectly. I will set and sync base timing before
beginning the tune using a timing light, but I want you to make sure it is close and that something else is not
“off” before beginning the tune. If the timing belt is aligned incorrectly, this will increase the cost of the
appointment if I need to fix it during the tune or end the day early for you if you don’t have additional funds in
your budget to fix it correctly. A motor cannot be tuned properly with cam timing set incorrectly.
Tires, Alignment and Suspension ______ initial
The dyno we use is a small roller dyno, Mainline AWD Digital unit. Very sticky tires or slicks DO
NOT work very well with our dyno rollers. Normal everyday street tires (all season or summer) work best for
traction, wear and HP readings. Please do not arrive with sticky tires, semi-slicks (BFGs) or full slicks…if
these are the only tires you have, please call ahead of your tune and we will make other arrangements if
possible. A vehicle out of alignment will measure LOWER HP than one in correct alignment. If you are
concerned with HP #s, please make sure you give yourself the best chance of achieving your goals.
Your suspension should be set properly and all bolts, ball joints, tie rods and bushings should be in good
shape. Cars are driven in excess of 130 mph sometimes on the dyno and a suspension failure at that speed in
this environment could be extremely dangerous. If I look at your car when it comes in and notice a potential
problem, I will turn the car away and your deposit will not be refunded.
For ride height, please do not bring in completely slammed to the floor cars, a normal aggressive street
drop of 1-2” is fine…any lower we may have issues with exhausts hitting, tires rubbing or other. When the car
is strapped to our Mainline AWD Dyno, instead of holding the car in place on top of rollers like a Dynojet or
Mustang dyno, the car is strapped over the lower control arms and is pulled DOWN into the dyno which lowers
it even more while strapped down. Please do not ignore this.
Please Initial Tire Check ______ Suspension Check ______ Ride Height Check ______
Check Engine Lights ______ initial
The car should have ZERO Check Engine Lights. Please do not make an appointment or come until all
check engine lights are cleared. If you need help with this, please call or email us well before your appointment
and we will help guide you on this. If your car arrives with a check engine light, please expect to pay labor for
fixing the light. If it is something we are not able to fix on that day, your car will not be tuned and your deposit
will not be refunded. Exceptions to this are O2 sensor codes or the knock sensor…these can generally be
disabled in the software being used but please call us prior to the tune if you have any lights.
4
Electrical and Wiring ______ initial
All wiring should be solid and correct before arriving. Connections that aren’t at least crimped or
soldered can vibrate loose and cause intermittent issues or worse, engine failure. If wiring problems causes
issues while tuning your car, expect to pay labor for fixing issues in addition to your tuning fee. If any wiring
issues cause harm to tuning gear that is attached to your car, you will be expected to pay for my replacement
cost of those items. All grounds should be clean (no paint underneath ground wires), connected in the correct
spots and corrosion free. Your alternator, battery and charging system should be operating up to par charging
the car somewhere in the 13.5 – 14.7 volt range. Any lower or any higher and there can be problems tuning the
car properly. Make sure all BELTS are tensioned correctly.
Fuel System ______ initial
Your fuel system should be designed to support the Horsepower goals you have for your setup. Properly
operating injectors, fuel pump and fuel pressure regulator are required with ZERO leaks. If there is any
question about what fuel pump is in your tank, I suggest you remove it and replace it with a proper Aftermarket
Fuel Pump for your car. We carry fuel pumps in stock if you need one. In rare cases if you need this done, we
can supply the fuel pump and we can install this for you for a charge on the day of the tune. Do not install a
fuel pump in a dirty or rusted fuel tank…you will have issues immediately or later on down the road when your
fuel supply is cut off and engine damage occurs. Fuel filters are important to keep everything running nicely.
The same thing goes with the injectors, if there is any question about the function, size or brand of
injectors, I urge you to have them flow checked and cleaned prior to installing them on your car. If you
purchase them new, you should not have to do this. Injectors can be installed as well on the day of the tune if
you need this done for a charge. If you install the injectors yourself, please make sure they are secure in the
intake manifold and in the fuel rail with good o-rings. Please do not use cracked or worn o-rings on either side
of the injector and do not FORCE these in when installing them. We do stock a variety of injectors in-house
and we can install them on the day of the tune if needed.
You can use a stock fuel pressure regulator in most cases rather than spending money on an aftermarket
piece for N/A or boosted setups under 15 psi…I do suggest though that you acquire a fuel pressure gauge that
installs on an aftermarket fuel rail or on the stock fuel filter. If you do go with an aftermarket regulator,
PLEASE use a well-known brand name and not some knock-off…your fuel system is the most important
system and good parts need to be used…there is no breathing room when your motor is starved for fuel.
What Fuel are you Using: _______________ Fuel Pump Used: ____________________
Injectors Used: ____________________ FPR Used: ____________________
Ignition and Spark ______ initial
Your ignition system is almost as important as your fuel system. Without proper spark, there will be no
power and the car cannot run to its full potential. Please make sure your coils/distributor are working correctly.
See a Service Manual for procedures on how to check your Coil and Ignitor (ICM). Make sure you have a clean
(or new) rotor and cap…and make sure the little rubber seal around the outside of the distributor is present and
in good shape to keep moisture out of the inside. Your spark plug wires should be working well, I also like
OEM stock plug wires or NGK. I highly suggest staying away from ALL MSD products including external
coils, digital spark boxes and plug wires. I have never experienced one benefit to using an MSD product
personally. If your arrive with MSD parts on your car, I will tune it, but if the part fails while tuning or is bad
from the start, there will be an extra charge or your car may not be able to be completely tuned and you will still
be responsible for all of the tuning fees. OEM parts have been used on many 600+ HP cars…there is no need
5
for aftermarket ignition products unless you have a completely serious race car, and then there are many other
better products to use rather than MSD.
Make sure your spark plugs are in good shape and gapped correctly. We stock spark plugs here but if
you don’t want to purchase a set from us, please have at least one or two extra sets with you when you come for
your appointment. Please call well before your tuning appointment if you need recommendations on which
plugs to run for your application. Any car being tuned on Hondata S300 or KPRO will need to be running
Resistor Plugs, please do not use Non-Resistor Plugs in these applications or there are side effects with the
Hondata hardware. We do carry plugs in stock for our most common applications.
Engine Fluids ______ initial
Make sure you are running the proper amount and proper weight of oil for your application. There
should be ZERO oil leaks from the motor for obvious reasons, no exceptions please. Make sure all seals are
tight, and that your drain bolt is secure.
Your coolant system should be running a 50/50 water/glycol mixture or straight water with additives for
your track car (normally just straight water with water wetter). There should be no leaks in the radiator, cap or
lines…you should have an overflow reservoir and the system should be properly bled and hold pressure. All
clamps should be checked and secured prior to arriving for your tune.
O2 Sensor Bung ______ initial
You NEED to have an O2 Sensor bung, easily accessible and free and clear from any objects. If you
have an O2 sensor currently in a bung in your exhaust, please make sure it is not rust-locked in there and it is
able to be removed. If the plug or installed O2 sensor isn’t able to be easily removed, you may incur extra labor
charges. If you show up without an O2 bung, I may have to put a clamp in your exhaust which is not as
accurate and harder to get a good tune with for idle and part throttle. The O2 sensor bung needs to be 12-18”
from the turbo outlet if you are running a turbo. If you are N/A or Supercharged, the bung needs to be in the
exhaust where ALL exhaust gases travel by…do not put a bung in one or two runners on a header…this can
potentially give the tuner bad information and will throw things off. We can also use an o2 sensor off the
exhaust in most cases as well using a pipe sniffer as long as there are no leaks in your exhaust.
Exhaust System ______ initial
Your exhaust system should be free from leaks, cracks or other issues as leaks in the exhaust before the
O2 sensor can throw off readings. I am a big believer of high flow catalytic convertors. Your manifold should
be secured to the head of the motor with all bolts and a leak free gasket. If you are running a turbo, it should be
secure to the manifold with at least (suggested) 2.5” downpipe and a DUMPTUBE should be venting exhaust
gases below the oil pan with an externally gated waste-gate setup. If you arrive without a dump tube, we may
not be able to safely tune your vehicle. If you don’t have a FULL EXHAUST exiting out from the back bumper
or a dump tube, I need to be made aware BEFORE you arrive…no exceptions.
TRACK ONLY VEHICLES __________________________ SIGNATURE, Date __________
In accordance with the CLEAN AIR ACT, we do not tune, modify or adjust ANY system, mechanical or
electrical parts that may affect your vehicles emissions for street vehicles. Therefore we ONLY provide ECU
tuning and other services for vehicles that will be used in racing applications ONLY. In many instances we do
allow others to rent our dyno to tune their own vehicles, if you are in this category, any modifications you do
are at your own risk!
6
Common Sense Check ______ initial (Do NOT Initial this box to show you are ACTUALLY
reading this document)
If you think something is apt to fail, it probably will. Perform a complete common sense check of your
entire setup and car before coming in for your appointment. If you have rubber hoses near a hot manifold, they
are probably going to melt. If you have a loose wire or ground, it is probably going to cause issues with the
tune. If you are spending good money on a tune, you are going to want to get the best bang for your buck. If I
have to fix common sense issues that should have been addressed prior to your arrival to complete the tune,
there will be an extra charge. I will help you by answering any questions before the tune to get these potential
issues fixed free of charge! I want your tuning experience to be positive, but I cannot do my job with
mechanical or electrical issues.
DO NOT ARRANGE TO PICK UP YOUR TRAILER ON THE MORNING OF YOUR TUNE. Most
likely UHaul or whoever will mess up your reservation and make you late or cause you to miss your tune.
Load your car on a trailer the NIGHT BEFORE!
Engine Break-In Procedures (for a freshly built motor)
If this is a new motor build that you are bringing for a tune, to save yourself money, and to make sure
you get the most out of the time allotted for tuning, I urge you to do research and follow the recommendation of
your engine builder. We have a write-up on our support site that may give you some guidance on this as well.
Please visit SUPPORT.XENOCRON.COM for instructions on products we sell, along with
helpful write-ups, links to other sites and general information about tuning and parts that we
carry.
7
Optional Suggestions & Procedures to Perform
Leak Down Test
Similar to a compression test, it’s another measure of your engines health. There shouldn’t be any more
of a leak down than 10% in any one cylinder. If you are seeing more than 10%, try to find where the air is
leaking. You can do this by listening or feeling at the dipstick hole or by taking off the radiator cap and
watching for bubbles in the coolant. Air in the dipstick points to the piston rings, ring lands or the pistons
themselves. Air in the coolant points to head gasket issues, or cracked or sinking sleeves. Air coming out of
the Throttle Body means your intake valves are leaking and air out of the exhaust means your exhaust valves
are leaking. It is HIGHLY recommended to perform a leak down test on a new motor BEFORE installing it
into a vehicle.
VTEC, VTC (or any other variable cam) Operation
If your vehicle is running well on your basemap, check to make sure VTEC is operating properly by
slowly accelerating to your VTEC crossover point. Generally a very noticeable tone change occurs when the
engine switches to the VTEC cam profile. If you don’t hear this sound or notice a change, make sure there are
no check engine lights that relate to VTEC (VTEC pressure), make sure your car is completely up to temp and
make sure you are going faster than 20 mph when you are attempting to test this. Also, make sure VTEC is
activated in the chip you are running and you know where it is set. In all cases this is not possible to test ahead
of time, but if you can make sure, it will make tuning the car easier. Any limiters to cam shaft phasing must be
mechanically installed prior to the tune.
Vehicle Alignment
Getting a professional, proper full vehicle alignment is one of the best things you can do for a fast car. It
will track straight and be more responsive at higher speeds, which is imperative with all cars that I have tuned
or done work on. Having your wheels balanced is certainly recommended as well. It will also help the car
track better on the dyno rollers and keep it from pulling and make it safer to operate on the dyno. A poor
alignment will register as LESS POWER on the Dyno because of friction losses.
Lips, Side Skirts, Rear Diffusers and Body Kits
I would suggest that if you have any of these items, you remove them before coming to the dyno if you
suspect they might hit or come close to hitting when the vehicle is operated on the dyno. If I have to remove
them to get the car to clear on the dyno, there will be an extra charge. Under panels may also prohibit proper
strapping.
Replacement Parts
Any parts that you have spare parts for or feel might fail on the dyno, bring those replacement parts with
you. So many times people have come to get tuned and had a part fail on them and of course they have a
replacement for that part or something that will work at home. Please bring anything you feel might help you
out.
Bring Your Tools to the Dyno
If there are things on the car that might need to be fixed, and you are mechanically capable of fixing
those while on the dyno, bring your tools with you. I have no problem with you fixing your own car while it’s
on the dyno, but you need to use your own tools, not mine. If you are using my tools or equipment, it will be
the same charge as if I was working on the car.
8
Address to our physical shop location:
Xenocron Tuning Solutions
301 Route 17S (Old Route 17 or Route 17 S)
Human Entrance is Unit 1 (Dyno is in Unit 10)
Hillburn, NY 10931
GPS systems don’t seem to find our address very well…below are some directions that may help you.
Please arrive BEFORE your scheduled tuning appointment time. My time is as valuable
as your time, so please respect that...arriving on time also allows me to spend more time
actually tuning your car, rather than waiting for it to arrive. A properly running car
should easily be able to be tuned in the ~2-4 hour window I allot for…and sometimes I
schedule tunes back to back from one another. If you arrive late, I cannot let your
tardiness cut into someone else’s tuning time who might be scheduled after you. Please do
not bring an entourage of people with you…I prefer to have the owner of the car there
with no more than one friend, girlfriend or the mechanic who works on your car. If you
bring more than yourself and one friend, I will have to ask the others to wait outside. From Tappan Zee Bridge (Route 87/287 Thruway Westbound/North): Proceed to Exit 15A. Make right at traffic light and the next immediate right again. This is our road…you will pass under an overpass, (Thruway), go straight to #301, a small Brown Building, entrance will be on your right. From Thruway (Route 87 south) Eastbound/South: Proceed to Exit 15A. At end of exit make left, proceed approx. ¼ mile to #301, a small Brown Building, entrance will be on your right. From George Washington Bridge/ Palisades Interstate Pkwy. Head North: Proceed to Exit 9, West towards Albany. You will be on N.Y.S. Thruway Westbound. Proceed to Exit 15A, follow directions as #1 from Exit 15A. From Palisades Interstate Pkwy, South: Exit at 9, West/Albany. Follow directions as #3 from Exit 9 West. From Lincoln Tunnel: Route 3 West to Route 17 North. Stay on Route 17 North approx. 20 miles. Route 17 North merges with N.Y.S. Thruway. Continue onto N.Y.S. Thruway North to Exit 15A. Follow same directions as #1 from Exit 15A. From South/Central New Jersey: Garden State Pkwy. North to the end. Bear left onto N.Y.S Thruway North/Albany. Proceed to Exit 15A. Follow same directions as #1 from Exit 15A. From Morristown, Wayne Area: Take Route 287 North to N.Y.S Thruway (87) North. Exit at 15A. Follow same directions as #1 from Exit 15A.
GOOGLE Maps Search “XENOCRON TUNING SOLUTIONS
FACEBOOK Search “Xenocron Tuning Solutions”
845-504-5340 (phones are NOT on afterhours or weekends)
Please call if you have any problems when trying to find us.
9
Xenocron Tuning Solutions, INC. “XTS” and Mainline/Dynolog Dynamometer
Waiver, Disclaimer & Absolute Release
1. As the “Customer” I hereby represent that I have read, understand and have completed ALL ABOVE
procedures and checks and that I have full authority to authorize the testing/tuning of this vehicle and to
enter into this Waiver/Release.
2. I am aware that all tests are intended to be and will be at maximum performance and at wide-open
throttle, thus applying stress similar to that which the vehicle would experience during operation on the
road/track and is therefore susceptible to the same risks as on the road/track which may cause engine,
power train and/or tire/wheel failure or damage.
3. As the “Customer” I know and accept ALL risks of running my vehicle on the dynamometer.
4. As the “Customer” I hereby represent that I know the complete condition of the vehicle and I assure
that it is in acceptable condition to run on the Dynamometer. I have been advised that XTS does not
know, nor assumes any such knowledge of the condition of the vehicle being tested/tuned and I
nevertheless, agree to have my vehicle run on the Dynamometer. As the “Customer” I represent that
all parts of the vehicle are in good condition and are capable of full power and full throttle performance
during any testing/tuning being performed.
5. Therefore, I hereby release XTS and Mainline Dyno from any liability of any nature for damage or other
losses which may be sustained as a result of the testing/tuning on the Mainline AWD Chassis
Dynamometer.
6. I assure XTS that my vehicle being tuned or modified is being used for RACING purposes ONLY and
will not be driven on public roads at any time.
Please complete ALL of the following vehicle information
Vehicle Make ____________________ Vehicle Model & Year ____________________
Engine Type ____________________ Rev Limit Requested ____________________
Fuel Used ____________________ Auto or Manual ____________________
VIN # ____________________ Turbo, S.C. or N/A ____________________
XTS Reserves the right to decline or discontinue dynamometer services for any reason at any time. By signing this waiver, the
customer authorizes XTS and its employees to operate the vehicle in the manner and to the limits stated above. With my signature, I
agree to all conditions, risk and self-liability of my vehicle and agree to hold XTS and Mainline Dyno free from any liability and cause
of action, which might arise from the use of my vehicle on said equipment. When tuning your vehicle, if the ECU or tuning solution
allows for “tune locking” we reserve the right to choose to lock or not lock the tune at our discretion. By signing this, you agree to
that fact as well.
PRINTED NAME: ___________________________ SIGNATURE: _____________________
DATE: ___________________________ MEDIA OK? _____________________
ADDRESS: _____________________________________________________________________
EMAIL: ___________________________ PHONE # _____________________
Level of Risk You Are Comfortable With (circle 1 – 10, 1 means LOW, 10 means you are ok with risk)
1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 – 9 - 10
PLEASE PAY CLOSE ATTENTION TO THE DYNO OPERATOR AT ALL TIMES AND LISTEN CAREFULLY TO INSTRUCTIONS
DURING VEHICLE TESTING
10
Things I WILL NOT Do
Do not even bother asking me to do these things because it will not happen:
- Street tunes – I have a family that depends on me. I can’t afford to die while driving in your race car. I
use a dyno to have a controlled environment for tuning. Under no circumstances will we go on the street
with your vehicle. We can provide a LOG review of you on the track, provided by you via email after
the tune. If you would like me to check a LOG of you on a racing track after the tune, make sure you
have a log equipped ECU, and an O2 sensor that is wired to the ECU to be able to log accurate Air/Fuel
Ratios.
- AEM FIC, Greddy EManage, SAFC, pretty much any other piggyback.
- Guess your Horsepower “on your setup” before the tune.
- Tune pump gas or any setup to the limit, “safely” (high compression, high boost, etc). To find a LIMIT,
you have to break things, unfortunately.
- OBX Products, these are all crap…they all break eventually or have issues. If you show up with OBX
products on your car, or SSAutoChrome or any Ebay type brand, expect that I will suggest you not even
attempt to tune. We will still tune the car for you, but will state our feelings again on these products.
- Same goes for the following fuel injectors. Southbay, Five-O Motorsports, Injector Nation or any other
Ebay brand, no-name, Asian knock-off injectors that will be an issue. There will be no support for any
idle, part throttle or weird running issues you might incur running these injectors. Use proper injectors
with data from reputable companies like Injector Dynamics and Fuel Injector Clinic.
- Action Clutch, garbage
- Blox Cams and Cam Gears…good luck.
11
PRE-TUNING CHECKLIST (short sheet)
Compression Test Results #1_____ #2 _____ #3 _____ #4 _____ #5 _____ #6 _____ #7_____ #8 _____
Leak Down Test Results #1_____ #2 _____ #3 _____ #4 _____ #5 _____ #6 _____ #7_____ #8 _____
Boost Leak Test Performed? YES NO Max PSI Achieved with no Leaks _____ psi
Injector Size & Brand _____________________ New, Used or Freshly Flow Tested (provide sheets)?
- Please provide ANY manufacturer data sheets at time of tune (addt’l costs if no data provided)
- Fuel Pressure set to _______ psi (don’t say STOCK)
Camshaft Specs, if cams were degreed, please provide a complete CAM CARD with information. If no
information is provided, I WILL NOT TOUCH CAM GEARS
Valve Adjustment Checked and Set to the following: INT _______” EXH _______”
Bore and Stroke, don’t just say “stock” ____________________________________
Engine Build Details, what pistons, what compression, what rods, what rod bolts, what oil pump, an engine
build blueprint sheet would work nicely here! Also, who performed all work?
_______________________________________________________________________________________
Base Timing Checked and set with a timing light? YES or NO
All engine fluids, filled, bled and checked? YES or NO
Easily accessible O2 Sensor Bung in the exhaust and also LEAK FREE? YES or NO
- Knowing my dyno setup please try to think in advance of any possible exhaust or interference issues
Will the customer need fresh spark plugs when they arrive at the dyno? YES or NO
Customer and Shop Signed Liability Waiver/Release Included? YES or NO
My dyno likes street tires, NO SLICKS, NO SEMI-SLICKS on the drive wheels _______ initial
Zero Check Engine Lights _______ initial
12
2018 Flat Rate Retail Price list: Honda/Acura
ANY Stock Honda ECU “Tunable” Vehicle with BOLT –ONs only - $400
- Must have stock injectors, maf/map, and engine must be 100% internally stock (no SWAPS)
- Hondata (S300, KPRO or FLASHPRO), KTUNER, Neptune (OBD1) only (Hardware discount N/A)
Honda Chip Tuning using NEPTUNE Dealer Software $600 (pump gas, N/A)
- Add Nitrous or One Boost level (wastegate) +$100
- ECU Controlled PWM Boost by Gear +$150 (must have Solenoid and ECU components already)
- Prices includes Neptune Chip Tuning License Fee (one time purchase)
Hondata S300 or Neptune RTP - $500 (pump gas, N/A)
- Add Nitrous or One Boost level (wastegate) +$100
- ECU Controlled PWM Boost by Gear +$150 (must have Solenoid and ECU components already)
Hondata KPRO - $500 (pump gas, N/A)
- Add Nitrous or One Boost level (wastegate) +$100
- ECU Controlled PWM Boost by Gear +$150 (must have Solenoid already)
Hondata FLASHPRO - $500 (pump gas, N/A)
- Add Nitrous or One Boost level (wastegate) +$100
- ECU Controlled PWM Boost by Gear +$150 (must have Solenoid already)
- If using our DEALER FLASHPRO, add $295 to prices above (see additional notes)
Haltech ELITE ECUs, Pro Plugin, Platinum Sport 1000/2000 - $600 (pump gas, N/A)
- One Boost level (wastegate) +$100
- Multiple Boost Levels (PWM Boost by Gear or Electronic Boost Controller) +$150
AEM Series II - $600 (pump gas, N/A)
- One Boost level (wastegate) +$100
- Multiple Boost Levels (PWM Boost by Gear or Electronic Boost Controller) +$150
*** FOR ANY VEHICLE WE TUNE, WE INCLUDE ONE FREE TRACK SUPPORT SESSSION (In person or Remotely)
as part of the tune. In Person support is available if we are attending a popular event or remote support can be scheduled
in advance. Ask the tuner for details. Does NOT include chip tuning options.
All Hardware that we tune is available through Xenocron and discounts will be provided for ECUs, Sensors,
Injectors, etc that are purchased through Xenocron prior to the tune. Typical hardware or add-ons:
- Chip OBD1 Honda ECU $65 , Chip + Vtec convert $95
- Neptune RTP $400 installed into customer supplied ECU
- Hondata S300 $490 installed into customer supplied ECU - Add Boost by Gear (PWM) circuit- $30
- Hondata KPro $690 installed into customer supplied ECU, Hondata FlashPro $690
ANY Additional Fuel, Add $150
FLEX Fuel on any capable setup, Add $300
TRACK TUNING/SUPPORT - $400 per day (up to 4 cars, travel and expenses not included)
REMOTE Support/Tuning is available @ $100 per hour rate
Discounts:
Purchase tuning hardware at retail from Xenocron = $50 off tune
Repeat customer = $50 off tune
Retunes are $150 per hour, at full hour increments. Time starts when you arrive for your appointment!
ALL PRICING ASSUMES CASH AS THE METHOD OF PAYMENT!!!
13
2018 Flat Rate Price list: Non Honda/Acura
Motec M1, M84, M400, M600, M800 - $700 (pump gas, N/A)
- One Boost level (wastegate) +$100
- Multiple Boost Levels (PWM Boost by Gear or Electronic Boost Controller) +$200
- Additional Fuel +$150
- DBW Throttle Body +$100
- Cam Control (variable cam angel) +$100 (per cam)
- Every tune includes ONE FREE TRACK SESSION (see additional notes)
Haltech Elite, Pro Plugin or Platinum Sport 1000/2000 - $700 (pump gas, N/A)
- One Boost level (wastegate) +$100
- Multiple Boost Levels (PWM Boost by Gear or Electronic Boost Controller) +$150
- Additional Fuel +$150
- Every tune includes ONE FREE TRACK SESSION (see additional notes)
AEM Series II or Infinity - $700 (pump gas, N/A)
- One Boost level (wastegate) +$100
- Multiple Boost Levels (PWM Boost by Gear or Electronic Boost Controller) +$150
- Additional Fuel +$150
- Every tune includes ONE FREE TRACK SESSION (see additional notes)
UPREV (nissan) - $700 (pump gas, N/A includes one-time $300 Osiris License and 2 hours dyno time)
- $100/hr for N/A vehicle after initial 2 hour flat rate block
- One Boost level +$150 per hour after initial 2 hours @ $700
- Multiple Fuels +$150
Cobb Accessport (Subaru) - CALL
- Additional Fuel +$150
Cobb Accessport (Mitsubishi) - CALL
- Additional Fuel +$150
Discounts:
Purchase Standalone ECU hardware at Retail/MSRP from Xenocron = $100 off tune
Repeat customer = $50 off tune
Retunes are $300 minimum for 2 hours, $150 per hour for any additional time needed
FREE Track Support Session is typically for REMOTE work or if we are at the track for an event or another paid
customer. Expenses not included (driving to/from, entry to track or any other expenses incurred). Contact us for
more details if you would like to take advantage of this offer.
ALL PRICING ASSUME CASH AS THE METHOD OF PAYMENT!!!