8/3/2019 XG100 Flash Utility Guide v3.0
1/12
Janam XG100 Flash Utility Guide
Reference Guide
Version 3.0
This document will be treated as Confidential Information under the terms stated in theNon-Disclosure Agreement. No part of it may be circulated, quoted or reproduced for
distribution without prior written approval from Janam Technologies LLC .
8/3/2019 XG100 Flash Utility Guide v3.0
2/12
Janam XG100 Flash Utility Guide
This document describes how to download .NB0 files onto Win CE 6 (Craft) device
using USB cable.
!
1. Windows XP PC2. USB Mobile cradle or Single Cradle with a USB cable (A to B plug)3. 9V DC/2A Power supply.4. Files (*.NB0)
"#
1. Hardware setup is shown asFigure 1.
Figure 1: USB Cable Connection
Software setup: Installing USB Remote NDIS Device Driver on
Windows XP PC
For USB Image download, the RNDIS driver for the Windows XP PC has to be
installed first. Skip this procedure if the USB Remote NDIS Device Driver
installation has been done.
Instruction:
a) Setup a USB Connection asFigure 1.b) Press & release + buttons and immediately press & hold
+ buttons until the device enters Download Mode. The
device will display the splash screen for Download Mode asFigure 2.
XG100
(WinCE6)
USB Mobile/
Single Cradle
PC(WinXP)
DC Power
Supply 9V
USB Cable
DC Input
USB plug to
USB port
8/3/2019 XG100 Flash Utility Guide v3.0
3/12
Janam XG100 Flash Utility Guide
Figure 2: Splash screen for Download Mode
c) After few seconds, Windows XP shows a notification box to indicate that a newhardware device has been found. Refer toFigure 3.
Figure 3: New Hardware Found
d) On the next dialog box select Install from a list or specific location.
8/3/2019 XG100 Flash Utility Guide v3.0
4/12
Janam XG100 Flash Utility Guide
Figure 4: Select Install from a list or specific location (Advanced)
e) On the next dialog box key in the path where you would find the driver files forthe RNDIS KITL driver, under the folder of [ActiveSync_USB_Host_Driver].
Click button to proceed.
Figure 5: Browse for ActiveSync_USB_Host_Driver folder
8/3/2019 XG100 Flash Utility Guide v3.0
5/12
Janam XG100 Flash Utility Guide
f) Hardware Installation warning dialog box prompts. Click on button to continue.
Figure 6: Continue installation by clicking on button
g) Driver installation starts.
8/3/2019 XG100 Flash Utility Guide v3.0
6/12
Janam XG100 Flash Utility Guide
Figure 7: Installation in progress
h) Click on button when the driver installation is completed.
Figure 8: Installation completed
i) The setup is complete.
8/3/2019 XG100 Flash Utility Guide v3.0
7/12
Janam XG100 Flash Utility Guide
Procedure for Image Flashing
1. Setup a USB Connection asFigure 1.2. Press & release + buttons and immediately press & hold
+ buttons until the device enters Download Mode. Thedevice will display the splash screen for Download Mode asFigure 9.
Figure 9: Splash screen for Download Mode
8/3/2019 XG100 Flash Utility Guide v3.0
8/12
Janam XG100 Flash Utility Guide
3. Copy XGFlash.exe into the PC Desktop. Double click on XGFlash.exe tolaunch the XG Series Flashing Program as below. Refer toFigure 10.
Figure 10: XG Series Flashing Program
8/3/2019 XG100 Flash Utility Guide v3.0
9/12
Janam XG100 Flash Utility Guide
4. Switch to XG Series Flashing Program, click on toolbar. Browseto select the software image (ALLIMAGE.nb0) to be flashed into the device.Click on button. Refer toFigure 11.
Figure 11: Open ALLIMAGE.nb0 image file
8/3/2019 XG100 Flash Utility Guide v3.0
10/12
Janam XG100 Flash Utility Guide
5. Click on the toolbar to start downloading the image. Refer toFigure 12.
Figure 12: Download ALLIMAGE.nb0 file
8/3/2019 XG100 Flash Utility Guide v3.0
11/12
Janam XG100 Flash Utility Guide
6. Image downloading message is shown in XG Series Flashing Program. ACKis increasing from 0 to the full file size of the nb0 file, in this case is 61,734,912bytes. Message of Transfer of ALLIMAGE.nb0 has successfully completed is
also shown on the message box. Refer toFigure 13.
Figure 13: USB image download completed
8/3/2019 XG100 Flash Utility Guide v3.0
12/12
Janam XG100 Flash Utility Guide
7. Leave the device untouched until the image update process is completed. Thedevice will auto-cold boot with calibration screen appears asFigure 14.
Figure 14: Calibration screen appears after image flashing completed
8. Now it is safe to remove the connection from the PC.