openUP (July 2007)
Low-cost drip irrigation—A suitable technology for
southern Africa? An example with tomatoes using saline irrigation water
Louise Karlberga, Johan Rockströma, John G. Annandaleb and J. Martin Steynb
aStockholm Environment Institute (SEI), Box 2142, 103 14 Stockholm, Sweden bDepartment of Plant Production and Soil Science, University of Pretoria, Pretoria 0002,
South Africa
Abstract Using saline water for irrigation increases water productivity by freeing up fresh water
that can be allocated to domestic or other uses. Drip irrigation is widely regarded as the
most promising irrigation system in combination with saline water. Simple drip irrigation
kits that are affordable for smallholder farmers have successfully been implemented for
irrigation of vegetable gardens in several countries in sub-Saharan Africa. The possibility
of using low-cost drip irrigation with saline water to successfully irrigate a common
garden crop, tomatoes, was tested in this study. Two low-cost drip irrigation systems with
different emitter discharge rates (0.2 and 2.5 l h−1) were used to irrigate tomatoes
(Lycopersicon esculentum Mill. cv. “Daniella”) with water of three different salinity
levels (0, 3 and 6 dS m−1). In addition, plastic mulch to minimise soil evaporation was
also compared to a “bare soil” or uncovered treatment. Two consecutive tomato crops
(spring and autumn) were produced during two growing seasons, starting from September
2003 and ending in April 2004, at the Hatfield Experimental Farm in Pretoria, South
Africa. An average yield of 75 Mg ha−1 was recorded for all treatments and seasons,
which can be compared with the average marketable yield for South Africa of
approximately 31.4 Mg ha−1. Even at the highest irrigation water salinity (6 dS m−1), a
openUP (July 2007)
yield above the average marketable yield was achieved, indicating that low-cost drip
irrigation works well in combination with saline water. Furthermore, the study showed
that the choice of drip irrigation system with regard to discharge rate is of minor
importance when irrigating with saline water. However, combining low-cost drip
irrigation with plastic mulch increased the yield by on average 10 Mg ha−1 for all
treatments. For the bare soil treatments, rainfall had an important role in the leaching of
salts from the soils. Finally, the study showed that specific leaf area was higher at high
irrigation water salinities, which is contrary to results from other studies. To be able to
generalise the promising findings from this study, there is a need to mechanistically
model the impact of different climates, soils and irrigation management practices, as well
as the long-term sustainability of these systems.
Article Outline 1. Introduction
2. Materials and methods
2.1. Experimental set-up and management
2.2. Design of drip irrigation systems
2.3. Treatments
2.4. Measurements
2.5. Analysis of data
3. Results
4. Discussion
5. Conclusion
Acknowledgements
References
1. Introduction Access to safe water in large areas of sub-Saharan Africa is one of the major challenges
in the efforts of achieving the UN Millennium Development Goals (MDGs) of halving
openUP (July 2007)
the number of poor and malnourished (Falkenmark and Rockström, 2004). Three-quarters
of the world's poor live in rural areas and depend largely on agriculture as their main
source of income (IFPRI, 2004). In sub-Saharan Africa that figure is as high as 80%.
Rural livelihoods are strongly dependent on water, both for domestic and agricultural
purposes (FAO, 2000 and Rockström, 2000). The water productivity, i.e. the amount of
fresh water required to produce a unit biomass, of these agricultural systems is low;
however, studies have shown that several techniques such as the use of supplementary
irrigation (Barron, 2004), fertiliser (Stoorvogel and Smaling, 1990) and strategies to
minimise soil evaporation (Daamen et al., 1995 and Rockström, 2003), can increase
water productivity substantially. Using saline water for irrigation is another way of
increasing the water productivity by enabling more fresh water to be used for domestic
and other purposes. Saline groundwater from boreholes unsuitable for human
consumption is a potential water resource for agriculture in areas of water scarcity in sub-
Saharan Africa (Karlberg and Penning de Vries, 2004).
Saline water up to 11 dS m−1 has been used successfully for commercial irrigation of a
number of crops globally (Hoffman et al., 1990 and Rhoades et al., 1992). However, in
order to assure maximum yields from crops irrigated with saline water, it is necessary to
develop special management procedures (Pasternak and De Malach, 1994). Presently,
drip irrigation is widely regarded as the most promising irrigation system to use with
saline water (e.g. Meiri et al., 1992 and Suarez, 1992). Several factors contribute to the
good results obtained with saline water when using drip irrigation (Dasberg and Or,
1999): (i) less water use (high application efficiency) results in less salt deposited on the
field, (ii) avoidance of leaf burn, (iii) high frequency drip irrigation prevents the soil from
drying out between irrigation events, thereby avoiding peaks in salt concentration and
concomitant high osmotic potentials and (iv) salts are continuously leached out from the
wetted section and accumulate at the wetting front away from the active root zone.
Simple drip irrigation kits that are affordable and easy to assemble and maintain have
been implemented successfully for irrigation of vegetable gardens of small-scale farms in
several countries in sub-Saharan Africa, e.g. Kenya, Zimbabwe and South Africa (Du
Plessis and Van der Stoep, 2000, Kabutha et al., 2000 and Chitsiko and Mudima, 2002).
openUP (July 2007)
However, Karlberg and Penning de Vries (2004) conclude that research on the use of
saline water in low-cost drip irrigation systems is generally lacking.
Low-cost drip systems utilise gravity as the force to push water through the pipes.
Normally a head of only 0.5–1 m is used for bucket kits (Sijali, 2001). Using a head of
between 0.5 and 1.5 m, and 10 m long laterals results in an average emitter discharge of
approximately 0.2–3.0 l h−1 depending on the drip system (Chigerwe et al., 2004). This
figure can be compared with flow rates under conventional drip of approximately 2.0–
8.0 l h−1 (Dasberg and Or, 1999) irrespective of the length of the laterals. Low emitter
discharge rates lead to longer irrigation application periods, and therefore a more even
salt concentration compared to high emitter discharge rates. On the other hand, a very
low discharge rate might result in higher soil evaporation since the soil surface is wetted
for a longer period of time. The latter process leads to a lower irrigation efficiency and
higher soil salinities. To conclude, discharge rate might be a factor to take into
consideration when choosing between different low-cost drip-systems, although it is
unclear which discharge rate should be superior.
Irrigation efficiency could also be improved by using plastic mulch. A mulch prevents the
soil from drying out between irrigation events, and thus peaks in salt concentration in the
root zone can be avoided. Such peaks are believed to have a negative impact on growth,
and the use of mulch can therefore be expected to have a positive effect on yield under
saline water irrigation; however, it is unclear if this effect has any significant effect on
crop yield.
The aim of this paper is to test the possibility of using low-cost drip irrigation with saline
water to successfully irrigate a common garden crop, tomatoes, in South Africa. More
specifically, the objective was to compare the impact of irrigation water salinity on crop
yield using these systems. Furthermore, additional objectives were to test the impact of
discharge rates and the use of mulching on soil evaporation, soil water content, soil
salinity and crop yield.
2. Materials and methods A field experiment was carried out at the Hatfield Experimental Farm, Pretoria
University, South Africa (25°45′S, 28°16′E) during two growing seasons, the first from
openUP (July 2007)
September to December 2003, and the second from January to April 2004. These periods
coincide largely with the rainy season that occurs from October to March, during which
most of the average annual rainfall of 670 mm falls. The climate is characterised by dry,
mild winters and hot, wet summers. The hydro-climate is sub-tropical and semi-arid, with
an annual potential evaporation of 1650 mm year−1. A large part of the precipitation can
fall during intense thunderstorms, resulting in large quantities of run-off from the fields.
In addition, rainfall is erratic with frequent dry-spells.
2.1. Experimental set-up and management
Before planting in September, soil samples were analysed to design a fertiliser
programme. The soil has been classified as a sandy clay loam, consisting of
approximately 60% sand, 10% silt and 30% clay (Tesfamariam, 2004). Furthermore, the
mean field capacity is 28.4% volumetric water content, mean wilting point is around
15.8% volumetric water content and mean bulk density is 1.52 Mg m−3 in the uppermost
metre of soil. Prior to the experiment, the electrical conductivity (EC) of the water in the
dam used for irrigation was determined to be 0.22 dS m−1. Fields were ploughed and
fertiliser incorporated 2 weeks before planting using 165 kg N ha−1, 33 kg P ha−1 and
165 kg K ha−1. Raised production beds (6 m × 1.8 m) were made, each separated by a
0.6 m path (Fig. 1). Finally, the drip irrigation kits were assembled, black plastic mulch
rolled out and secured at the edges with stones, and each bed was pre-irrigated with 65 l
of water of treatment specific salinity. The same beds were also used during the second
season. Six-week-old tomato seedlings (Lycopersicon esculentum Mill. cv. “Daniella”)
were planted on the 9th of September for the spring season and on the 12th of January for
the autumn season. Each plot was planted with a total of 42 seedlings in 2 rows, with a
spacing of 1.2 m between rows and a spacing of 30 cm in the row, to match the location
of the emitters. This resulted in a density of 2.9 plants m−2. During the growing season,
additional fertiliser was applied as fertigation (spring: 37.6 kg N ha−1, 15.4 kg P ha−1,
111.4 kg K ha−1; autumn: 42.8 kg N ha−1, 15.4 kg P ha−1, 126.6 kg K ha−1) and sprayed
on the foliage (3.1 kg N ha−1 and 4.0 kg Ca ha−1 in both seasons) at regular intervals
throughout the experiment for all treatments. In addition, pesticides were applied due to
problems with cutworms and nematodes.
openUP (July 2007)
Fig. 1. (a) Layout of raised production beds and irrigation systems, and location of some
of the measurement equipment. Both plots are irrigated with the high discharge rate
system (microtubes). The plot on the right is covered with a plastic mulch, whereas the
one on the left is a “bare” or uncovered soil treatment. (b) A schematic illustration of the
drip irrigation systems seen from above. Left: Microtube (high discharge rate). Right: In-
line (low discharge rate). In the in-line system, the position of the measurement
equipment is portrayed as white circles.
Irrigation took place in the evenings around sunset. Each plot was irrigated from a
separate tank located at the end of the production bed into which salt and water was
added. All treatments received the same amount of irrigation water. The irrigation
scheduling (irrigation amount and frequency) was determined from modelling of tomato
plants with the use of regional climatic data from a previous year but with zero
precipitation, using a parameterisation derived from data on saline-water, drip-irrigated
tomatoes from Israel (Karlberg et al., 2006). Since the effect of water stress was not the
focus of the study, an irrigation schedule in which water did not limit growth at any stage
during the experiment was chosen. Fixed amounts of either 15, 30 or 50 l were given to
each plot every second day in the beginning of the growing season, and daily towards the
end of each season, depending on the estimated demand. In the case of rain, irrigation
was reduced by the corresponding amount of water that had fallen as precipitation even
for the mulch treatments. For the treatments with intermediate irrigation water salinity
(3 dS m−1), 1.76 g NaCl l−1 was added to the irrigation water, whereas the corresponding
figure for the high irrigation water salinity treatments (6 dS m−1) was 3.51 g NaCl l−1.
The resulting amount of irrigation water (daily values) for spring and autumn, as well as
daily precipitation are shown in Fig. 2. During the first season, a total of 300 g salt m−2
was added to the soil for the treatments with intermediate irrigation water salinity, and
double this for the treatments with the high salinity water. The corresponding figures for
autumn were 175 and 350 g m−2, respectively. Algal growth in the tanks posed the risk of
clogging emitters, and all tanks were therefore continuously treated with algae eating
bacteria and were also cleaned by hand at regular intervals. As the plants grew bigger
they were trellised, and fruit were hand picked as they ripened. Final harvest took place
openUP (July 2007)
on the 17th and 18th of December for the spring season, and from 21st to 24th of April
for the autumn season.
Fig. 2. Daily irrigation amounts for (a) spring and (b) autumn, and daily precipitation for
(c) spring and (d) autumn.
2.2. Design of drip irrigation systems
Each plot consisted of a raised production bed drip-irrigated with laterals connected to a
50 l tank (Fig. 1). A microtube system produced by International Development
Enterprises (IDE, CO, USA) was used to represent the high discharge system. This
system was developed for smallholder farmers and is therefore easy to assemble and
manage. It has an emitter discharge rate of about 2.5 l h−1at a 1-m head and a distribution
uniformity of about 85% (Chigerwe et al., 2004). Two 60 cm long microtubes extend
from the lateral and emit water at the end of each microtube. To represent the low
discharge system, we chose an in-line emitter system produced by Plastro Irrigation
Systems Ltd. (Israel). These laterals were designed for commercial farmers, but can
openUP (July 2007)
easily be connected to a simple bucket or drum and used for garden irrigation. It has an
emitter discharge rate of about 0.2 l h−1 at a 1-m head and a distribution uniformity of
over 95% (Chigerwe et al., 2004). Both systems had an emitter spacing of 30 cm. The
50 l irrigation tanks were positioned approximately 90 cm above the raised surface of the
beds. After a tank was filled with water, a tap located underneath it was opened and water
gravity fed into the laterals and was discharged through the emitters. Each emitter
irrigated one plant.
2.3. Treatments
The experiment was limited to 12 treatments arranged as a randomised complete block
design with 3 factors. The two drip systems with high (H) and low (L) discharge rates
were used to irrigate the tomatoes with water of three different salinity levels (low
salinity = 01 dS m−1; intermediate salinity = 3 dS m−1; high salinity = 6 dS m−1). These
treatments were repeated with plastic mulch (M) and under bare soil conditions (B). All
treatments were replicated three times. The exact position of each treatment within a field
was randomised separately for each replicate. To avoid edge effects, the first and last
production bed of each field were also planted with tomato plants and drip irrigated with
fresh water according to the same irrigation schedule as the other plots, but were not
included in the experiment.
2.4. Measurements
Measurements were taken at different intervals before, during and after the growing
periods. Above ground dry mass was determined using destructive samples to estimate
carbon allocation to leaves, fruit and stem. One plant per plot was collected
approximately every 2 weeks, by identifying an average sized plant for each treatment
and cutting the stem at the soil surface. A total of five samples were taken from each plot.
Samples were dried in an oven at 60 °C for up to 7 days and were subsequently weighed.
At planting, 20 seedlings were used for destructive sampling, which also included root
depth and mass. Moreover, at harvest, plants for destructive sampling were dug up to
allow both above and below ground measurements. Thus, root depth and mass could also
be determined at harvest, bearing in mind that some of the root system was undoubtedly
openUP (July 2007)
left behind in the soil. The destructive samples also enabled the determination of leaf area
using an LI 3100 belt driven leaf area meter (LiCor, Lincoln, NE, USA). In addition,
plant height and canopy diameter was measured throughout the experiment for all
treatments, and the onset of flowering and fruit formation was also recorded. At harvest,
total above ground biomass of the green parts (i.e. leaves and stems) was weighed in the
field for each treatment. In the same manner, total fruit biomass was weighed separately
and included both edible and inedible fruits.
Soil water content was recorded throughout the experiment at different depths using a
neutron probe model 503DR CPN Hydroprobe (Campbell Pacific Nuclear, CA, USA).
The instrument had been calibrated before the start of the experiment (Tesfamariam,
2004). Twenty-four neutron probe access tubes were installed in pairs in one of the
replicates, one in the wet area next to a plant and one in the middle of the plant bed, for
all 12 treatments. The neutron probe measured soil water content every 20 cm in the
uppermost metre of the soil profile. In addition, the diameter of the wetted area of the soil
surface around each dipper was measured for the plants adjacent to the access tubes
during the spring experiment.
Microlysimeters (e.g. Daamen et al., 1993) were used to measure soil evaporation from
the wetted area next to the plants and from the centre of the plant beds, for all bare soil,
low and high salinity treatments. Each lysimeter consisted of an outer liner pipe
permanently located in the soil, and an inner pipe (length: 150 mm; diameter: 82 mm),
which is the actual lysimeter used for sampling (Fig. 3). Before planting, all liner pipes
were positioned in the soil so that the upper part of the cylinder was level with the soil
surface. One-half of the liners were located in the wet area next to an emitter, and the
other half in the dry area in the middle of the production beds. Soil evaporation was
measured daily, starting from sunrise the morning after an irrigation event and ending at
sunset on the onset of the next irrigation event. During this cycle, consisting of 1–4 days,
one soil sample per lysimeter was used. Samples were collected at sunrise following an
irrigation event, by pressing the lysimeter into the soil until the entire cylinder was filled
with soil, and then carefully digging it up. Each sample was taken in the edge plots at the
same location as the outer pipe in the corresponding treatment plot, i.e. a lysimeter was
filled with wet soil if it was positioned in a liner located in the wet area of the soil and so
openUP (July 2007)
forth. Once excavated, the lysimeter was trimmed flush at the base, placed on a sheet
metal base plate and sealed with waterproof tape. The microlysimeters were then
weighed with a portable balance that weighed to ±1 g, and mounted in the corresponding
liner tube. Every evening at sunset they were collected, weighed and returned to their
locations in the field. At sunrise the morning after an irrigation event, a new cycle was
started and new soil samples were taken in the same manner. In case of rain, a cycle had
to be interrupted and a new cycle could only be started once the rain had ceased. As the
weighing process is extremely wind sensitive, all samples were weighed inside a box
placed in the field. Soil evaporation was determined from the difference in mass between
two measurements, and from the soil surface area of the sample. Two to three cycles of
soil evaporation were collected three times during spring (September, October and
November) and twice during autumn (January and March), resulting in a total of five
series.
Fig. 3. Left: Microlysimeters with soil samples in the field. The microlysimeter in the
lower part of the picture is located in the middle of the production bed, whereas the
second is located next to an emitter under the plant canopy. Right: The inner pipe of the
microlysimeter turned upside down with the metal base plate attached to the bottom of
the lysimeter with tape.
openUP (July 2007)
During the experiment, 12 ceramic cup soil water samplers (Soil Moisture Equipment
Co., CA, USA) were used to measure the electrical conductivity of the soil water close to
the stem and at the edge of the wetted zone at the soil surface, at two different depths (20
and 40 cm). The treatments chosen for sampling (all without mulch) were: high discharge
rate, high salinity; low discharge rate, high salinity; and low discharge rate, intermediate
salinity.
Intercepted Photosynthetically Active Radiation (PAR) was measured twice during the
spring experiment with the use of a sunfleck ceptometer (Decagon Devices Inc., WA,
USA). In addition, humidity, wind speed, solar radiation, air temperature and
precipitation was recorded on an hourly basis at a weather station adjacent to the fields.
2.5. Analysis of data
All statistical analyses were performed in STATISTICA ver. 6. Multifactor analysis of
variance (ANOVA) was used to compare the different treatments. Unplanned pairwise
comparisons were preformed using Tukey's HSD test to interpret interactions between
factors. The data-set on yield and the destructive samples from the autumn experiment, as
well as the soil water salinity measurements, contained missing values. In the case of
yield data, imputation by interpolating from other measurements was used to substitute
five values. However, the destructive samples data-set from the autumn season contained
too many missing values due to problems related to the calibration of the scales,
imprecise sampling and mixing of samples, and therefore the whole data-set was
excluded from the analysis. To overcome the problem with missing data in the soil
salinity measurements, mean values for each month were used. In order to achieve
homogeneous variances for the biomass data from the destructive samples, the ANOVA
was done on the logarithm of the masses.
3. Results Total yield, including inedible fruit, for each treatment is presented in Fig. 4. During
spring, the average marketable yield was approximately 94 Mg ha−1 whereas during
autumn the corresponding figure was 55 Mg ha−1, representing a significant difference
between seasons (p < 0.0001). Even the yield from the plants irrigated with the highest
openUP (July 2007)
salinity level (6 dS m−1), was above the average marketable yield of 31.4 Mg ha−1 for
South Africa recorded between 1098–2002 (FAO, 2004). Yield was significantly higher
at low irrigation water salinity than at high salinity levels (p < 0.0001). An unplanned
pairwise comparison using Tukey's HSD test for the various salinity treatments revealed
that this difference was only significant between low and high irrigation water salinity
(p = 0.0001), and between medium and high irrigation water salinity (p = 0.013). Despite
the reduction in yield under highly saline conditions (6 dS m−1), these treatments still
yielded on average 66 Mg ha−1 as compared with 80 Mg ha−1 for the fresh water
treatments. Mulch also had a significant effect on yield for all salinities and irrigation
systems (p < 0.0001), increasing the yield by 10 Mg ha−1 on average over all treatments.
There was no significant difference in yield between the high and the low discharge rate
systems, irrespective of salinity level. The analysis of the destructive samples taken
during spring confirmed the findings from the analysis of the final yield (Fig. 5). It was
found that, on average, above ground biomass was significantly higher at low levels of
irrigation water salinity (p < 0.0001), and for mulch treatments (p < 0.0001), whereas
there was no difference between irrigation systems.
Fig. 4. Total yield for all treatments for: (a) spring and (b) autumn. L: low discharge rate;
H: high discharge rate; 0: EC 0 dS m−1; 3: EC 3 dS m−1; 6: EC 6 dS m−1. Vertical bars
denote one standard deviation of the mean.
openUP (July 2007)
Fig. 5. Total above ground biomass from destructive samples for: (a) the mulch
treatments and (b) the bare soil treatments for the spring experiment (mean values for the
two discharge rate systems).
Soil water content was analysed for the root zone (upper 40 cm). As expected, the soil
was generally wetter closer to the emitter than in the middle of the production beds
(p < 0.0001), even though after rainfall events the soil was sometimes wetter in the
middle of the field for the bare soil treatments. Comparing only the data from the soil
close to the emitters, it was found that soil water content was higher at high salinities
(p < 0.0001) (Fig. 6). In addition, including plastic mulch affected the two irrigation
systems differently (p = 0.007). For the low discharge rate system, the soil water content
was significantly higher when mulch was included (p < 0.0001, Tukey's HSD), whereas
for the high discharge rate system there was no difference between the mulch and the
bare soil treatment.
openUP (July 2007)
Fig. 6. Soil water content measured close to the emitter in the root zone (upper 40 cm) for
both seasons for: (a) the low discharge and (b) the high discharge system. 0: EC
0 dS m−1; 6: EC 6 dS m−1; M: mulch; B: bare soil.
The analysis of the soil evaporation data revealed no significant difference between
systems during spring (Fig. 7), whereas during autumn, soil evaporation was found to be
higher for the low discharge rate system compared to the system with a high discharge
rate (Fig. 8) (p = 0.041). Moreover, there was no significant difference in soil evaporation
between salinity treatments for any of the seasons. Soil evaporation was higher from the
wet soil close to the emitters than from the centre of the beds (spring: p < 0.0001;
autumn: p = 0.001). There was a significant variation between series (i.e. between
September, October and November for spring, and January and March for autumn)
(spring: p < 0.0001; autumn: p < 0.0001) for both seasons, but not between days within a
openUP (July 2007)
series. Finally, measurements of the wetted area of the soil surface showed that the
diameter was around 30 cm for both systems.
Fig. 7. Soil evaporation during the spring season for: (a) the wetted soil close to the
emitters and (b) the soil in the middle of the production beds. L: low discharge rate; H:
high discharge rate; 0: EC 0 dS m−1; 6: EC 6 dS m−1.
openUP (July 2007)
Fig. 8. Soil evaporation during the autumn season for: (a) the wetted soil close to the
emitters and (b) the soil in the middle of the production beds. L: low discharge rate; H:
high discharge rate; 0: EC 0 dS m−1; 6: EC 6 dS m−1.
Soil water salinity was higher at high irrigation water salinity then at low (p < 0.0001)
(Fig. 9). However, no significant difference in mean soil water salinity was found
between the two systems.
Fig. 9. Soil salinity at four locations in the soil: (a) edge of the wetted zone, 20 cm depth;
(b) close to the stem, 20 cm depth; (c) edge of wetted zone, 40 cm depth; (d) close to
stem, 40 cm depth. L: low discharge rate; H: high discharge rate; 3: EC 3 dS m−1; 6: EC
6 dS m−1.
Specific leaf area was higher at high irrigation water salinity then at low salinity during
the autumn season (Table 1), whereas during spring no such relationship could be seen.
Interestingly, specific leaf area was also significantly higher for the mulch treatments
than for the plants grown without mulch during autumn.
openUP (July 2007)
Table 1.
Specific leaf area measurements for both seasons
Treatment Mean (m2 gC−1)a
Standard deviation
Range (m2 gC−1) p-Valueb n
Spring
Low discharge rate 0.0117 0.0023 0.0091–0.0141 ns 108
High discharge rate 0.0114 0.0023 0.0091–0.0131 108
0 dS m−1 0.0112 0.0022 0.0090–0.0131 ns 72
3 dS m−1 0.0115 0.0023 0.0090–0.0130 72
6 dS m−1 0.0118 0.0025 0.0093–0.0148 ns 72
Mulch 0.0116 0.0021 0.0093–0.0134 ns 108
No mulch 0.0114 0.0025 0.0089–0.0139 108
Autumn
Low discharge rate 0.0112 0.0044 0.0044–0.0167 ns 126
High discharge rate 0.0113 0.0045 0.0040–0.0174 108
0 dS m−1 0.0103 0.0037 0.0037–0.0155 0.000053 72
3 dS m−1 0.0116 0.0048 0.0043–0.0174 72
6 dS m−1 0.0118 0.0046 0.0047–0.0183 ns 72
Mulch 0.0116 0.0045 0.0047–0.0176 0.000487 108
No mulch 0.0108 0.0043 0.0037–0.0165 108
openUP (July 2007)
ns: not significant at the 0.05 level. a Unit is square metre leaf per gram carbon of leaf. b Calculated using Tukey's HSD test. For the different salinity treatments, the
comparisons were only made between low and medium salinity, and medium and high
salinity. A significant difference between either low or high salinity compared to medium
salinity, implies that there was also a significant difference between low and high
salinity, and thus this comparison was not made.
4. Discussion All treatments resulted in a total yield above or equal to the average marketable yield of
31.4 Mg ha−1 for South Africa (FAO, 2004). Thus, during this growing season, it was
possible to use water of a salinity up to 6 dS m−1 for supplementary irrigation of tomatoes
using low-cost drip systems at a garden scale. However, the results from the field
experiment also included inedible fruit, which should be borne in mind when comparing
the yield from the experiment with the average yield for South Africa. Furthermore, a
higher yield can be expected in a controlled field experiment compared to the on-farm
situation, due to factors such as reliable availability of fertiliser and irrigation water. The
yield from the second crop was significantly lower than the first. This result is to be
expected, since the experiment started with a non-saline soil (approximately 1 dS m−1 at
saturation), whereas the salinity treatments for the second season started with more saline
soils (e.g. a soil water salinity of 9 dS m−1 from the high salinity treatments). However,
this advantage might have been counteracted by the high load of salt due to the large
amounts of irrigation water applied to the fields in combination with very low rainfall
during spring, compared to the second season. Larger problems with pests during autumn
might also have contributed to the differences in yield. All in all, since climate varies
with season, it is difficult to compare yields between spring and autumn.
Increasing salinity levels in the irrigation water led to reductions in plant size and yield.
At high irrigation water salinities soil water content was generally high. This is likely to
be the result of lower plant water uptake, either caused by the smaller plant size (toxicity
effect), or causing the smaller plant size (osmotic effect). Soil evaporation was unaffected
by the irrigation water salinity level, even though canopy size varied between salinity
openUP (July 2007)
treatments. Soil samples were taken from the edge plots that were irrigated with fresh
water. Therefore, measured soil evaporation for the salinity treatments might be higher
than in reality, due to the effect of lower vapour pressure because of high soil salinity.
Soil salinity was higher for high irrigation water salinities than at lower levels, and soil
salinity was substantially influenced by rainfall. From the start of the experiment until
February, soil salinity kept increasing steadily. The heavy rainfall at the end of that
month and in March caused significant leaching of the salts and subsequently a decrease
in soil water salinity. Between February and March, the average soil salinity level in the
root zone fell between 3 and 5 dS m−1, depending on treatment, whereas soil water
content remained relatively constant during this period. Salinity levels continued to
decrease until the end of the second season, but they never returned to the initial levels at
the beginning of the experiment in September. It has been shown that the impact of an
individual rain storm can cause substantial leaching of salts from the soil (Hoffman et al.,
1990), and the onset of monsoon rains caused a sharp reduction of soil salinity in saline
water irrigated rice fields from 6 to 2 dS m−1 in Bangladesh (Mondal et al., 2001).
Salinity levels closest to the emitter seemed to fluctuate less over time compared to other
locations.
Mulching minimises soil evaporation and thus prevents large fluctuations in soil water
content, whereby peaks in soil water salinity occur. A positive effect of mulch on yield
was evident for all treatments; however, there was no difference in the magnitude of this
positive effect between irrigation water salinity treatments, indicating that fluctuations in
soil water content, rather than peaks in salinity concentrations was important for plant
growth. An additional benefit of mulch was the reduction of weeds. Mulch treatments
required a lot of maintenance in the beginning of the growing season when the plants
were small, as wind tended to lift the mulch up and cover some of the plants, which
caused occasional leaf damage. On sunny days the black plastic used in the experiment
got very hot, causing high soil temperatures underneath the sheets. This might have had a
positive effect on growth in the beginning of spring, but may otherwise have caused plant
stress. It is unclear as to how much of the precipitation reached the soil through the holes
in the plastic next to the plants, as opposed the amount that was lost as runoff. This
openUP (July 2007)
apparent drawback of increased runoff from the plastic is counteracted by the
concentration of precipitation next to the plants, due to the location of the holes.
A low emitter discharge rate keeps the soil water content relatively constant, resulting in
small fluctuations in soil salinity and thus lower salinity stress in comparison to high
discharge rate systems. However, when the soil surface is wetted for a long period of
time, the cumulative soil evaporation becomes high. Since irrigation took place at sunset,
both systems had almost finished irrigating by the next morning depending on the amount
of irrigation water used, and therefore this latter effect may not be of importance.
Furthermore, the soil wetting pattern and the ability to leach salts from the soil might
have varied between the two systems, although the area of the wetted soil surface was
found to be the same for both. Since no significant difference between the two drip
irrigation systems was found, neither in the final yield data, nor in the measurements on
above ground biomass, the combined effect of these processes might have been the same
for the two systems. Nonetheless, the analysis of the water balance data shows that soil
water content was not affected by mulching in the high discharge rate system, whereas it
was higher with mulch than without in the low discharge rate system, especially at low
salinity. Assuming that transpiration is proportionate to total above ground dry matter
within each salinity treatment, and that transpiration equals plant water uptake, both
systems transpire approximately the same amount of water per salinity level. Thus, the
withdrawal of water from the soil by plant roots is not likely to have caused these
differences in soil water content in the root zone with and without mulch between the two
irrigation systems. Measurements of soil evaporation showed that the system with a low
discharge rate had a higher average evaporation rate (5.13 mm day−1) than the other
irrigation system (4.24 mm day−1) during autumn. This is probably due to the longer
duration of irrigation in the former case, causing the upper soil in the slow discharge rate
system to be wetter in the morning following an irrigation event, thus leading to higher
soil evaporation. Soil water content is also affected by drainage, which might have been
higher for the high discharge rate system due to the higher application rate. However,
since no measurements were made on drainage, this variable remains unknown.
At low salinity without mulch, water is lost from the soil through drainage, water-uptake
and soil evaporation. By covering the soil with a plastic sheet, soil evaporation is
openUP (July 2007)
minimised and thus some water is saved in the soil. In the high discharge rate system this
water seems to be taken up by the plant, since soil water content remains the same as
without mulch, whereas plant growth and thus transpiration is higher. The high discharge
rate system lost less water from the soil as evaporation whereas drainage is assumed to be
higher, resulting in similar soil water contents for the two irrigation systems. Since soil
evaporation is high for the system with the low discharge rate, the inclusion of mulch in
this system has a large impact on the soil water content. In this system, the water that is
saved by mulching is partly used by the plant, expressed as a higher growth compared to
the bare soil treatment, but some water remains in the soil, causing the observed
difference in soil water contents between the mulch and bare soil treatments. It is likely
that water uptake had reached a point where water was no longer limiting to plant growth,
and this is why the plants in this treatment did not utilise all the extra water in the profile.
The higher soil evaporation and the assumed lower drainage in the low discharge rate
system as compared to the high discharge rate system, implies a higher accumulation of
salts in the former system. However, measurements of soil water salinity showed no
difference between systems. Even so, soil salinity levels seem to fluctuate more in the
high discharge rate system, which might be due to larger variations in soil water content
caused by the high infiltration rate, leading to a drying out of the surface soil between
irrigation events. Thus, a measurement taken directly before irrigation might be
substantially higher than the mean soil water salinity during the irrigation cycle. From
this perspective, a comparison of the measured values of soil water salinity from the two
different irrigation systems might be misleading. Further, the impact on growth of these
peaks in salinity concentration is difficult to estimate. Since no difference in yield was
seen between the two systems at high salinity, it is assumed that the combined effect of
all factors affecting soil salinity was of the same magnitude for both systems.
Some temporal patterns were seen in the measurements, especially for soil evaporation.
During spring, potential evaporation increases with time. As the plant grows it shades
more and more of the wetted area surrounding the emitter. The combined effect of these
two factors results in small differences over time in soil evaporation from the wetted area
during spring, whereas for the dry area the difference in evaporation between series is
more dependent on rainfall. On the other hand, during autumn soil evaporation from the
openUP (July 2007)
wetted area shows a marked decrease from the beginning of the season to the middle of
the season, probably caused by a larger shading effect from the plant canopy in
combination with a lower potential evaporation. As for spring, soil evaporation from the
dry area seems to be mainly dependent on rainfall.
No strong relationship between salinity and specific leaf area was found, which
contradicts the findings of Taleisnik (1987), Brugnoli and Björkman (1992) and Marcelis
and van Hooijdonk (1999). Generally, the variation in measurements was higher at high
salinity, which was also the case in the study on radish (Raphanus sativus L.) by Marcelis
and van Hooijdonk (1999). As has been shown by others (Gary et al., 1993 and Marcelis
et al., 1998), specific leaf area is a very variable characteristic, and the absence of a
strong relationship between specific leaf area and salinity might be due to a high degree
of variation in the data.
The results of this study indicate that both irrigation systems are suitable to use in
combination with saline water, and can give good yields. However, at the end of the
second season, soil water salinity levels were higher than they were at the beginning of
the experiment, indicating an accumulation of salts in the root zone. Since the likelihood
of rainfall between April and September is low in this region, the soil water salinity levels
at the end of the experiment represents this year's annual build-up of salt. It is unclear if
this accumulation would continue if the same irrigation practices continued yet another
year, or if the soil water salinity would fluctuate around approximately the same levels.
One of the most determining factors seems to be heavy rainfall, causing leaching of salts
from the soil profile. Since rainfall is erratic in the semi-arid tropics, it is difficult to
predict the long-term sustainability of these systems without using a tool, such as a
simulation model, in which the important processes in the system are accounted for under
varying climatic conditions.
The potential yield increase from adopting the technologies used in this study must be
weighed up against the costs involved in buying, installing and maintaining the systems.
In the case of saline water irrigation, yield loss caused by salinisation must be weighed
against the benefits of being able to allocate more fresh water from irrigation to domestic
use, and the benefits relating to reduced risk of crop failure due to drought when using
supplementary irrigation. In India, a bucket drip irrigation kit irrigating over 100
openUP (July 2007)
individual plants over a 25 m2 area cost US $5 per kit, including the bucket (Postel et al.,
2001), making drip irrigation an affordable technology even for resource poor farmers. A
cheap alternative to plastic mulch is to use crop residues from a previous crop to cover
the soil. Crop residues have profound water conserving effects; they increase infiltration
of rainwater, as well as reduce run-off and soil evaporation (Erenstein, 2002).
The second crop was more affected by pests than the first, which most likely caused a
significant reduction in yield. However, the target group of this study, namely the rural
farmers, would probably not grow a large monoculture twice in a row. On the other hand,
the larger problem with pests during autumn could also have been due to the fact that this
season was a lot wetter than the previous season. Nonetheless, this difference between
seasons caused increased variation in data, which complicated the analysis of the results.
Another source of error stems from the fact that soil water content and soil water salinity
were measured at the same location on each plot throughout the whole experiment. This
means that if there was any disturbance of the soil right next to the measurement points,
the whole measurement series from that treatment might be skew. For example, if the
emitter next to the neutron probe access tube was suddenly blocked, the measurement of
soil water content for that treatment will be lower than the mean value for that plot.
Evaporation from microlysimeters has been shown to be consistent with the evaporation
calculated by gravimetric methods for the first 4 days after core extraction (Daamen et
al., 1993). However, the same study showed that the largest errors in measurements are
caused by the boundary to water flow imposed at the base of the lysimeter at the time of
core extraction, and it is therefore recommended that soil samples should be renewed at
least daily. This recommendation was not followed in this study, due to time and labour
constraints, and might therefore have caused some errors in estimated soil evaporation.
Finally, the imputation used to substitute missing values in the statistical analysis
decreased the variance of the samples; however, the number of missing values were few
in relation to the whole sample which means that the effect of the imputation is probably
rather small.
It is possible that the outcome of this study would have been very different for a different
soil, climate and crop. A more salt sensitive crop could for example have preformed
differently to tomato under the prevailing climatic conditions and treatments. The first
openUP (July 2007)
growing season was very dry and most of the rain came late. Higher rainfall earlier in the
season would most likely have led to higher crop yields for the salinity treatments. To
evaluate the impact of the environmental conditions, the data obtained in this study could
be used in combination with a simulation model. Several transient models for estimating
water uptake under matric and osmotic stress have been developed (e.g. Nimah and
Hanks, 1973, Letey et al., 1985, Cardon and Letey, 1992 and Pang and Letey, 1998).
Recent advances of crop growth models have led to the incorporation of more detailed
growth functions into the transient models (e.g. van Dam et al., 1997 and Stöckle et al.,
2003). Furthermore, biochemical photosynthesis models based on the work by Farquhar
et al. (1980) have been developed by several research teams (e.g. Sellers et al., 1996 and
Dai et al., 2004). Karlberg et al. (2006) incorporated a biochemical photosynthesis model
into an ecosystem modelling package, including a transient model for water uptake under
matric and osmotic stress, and a model for increased plant respiration due to ion toxicity.
Thereby, the modelling package could account for processes such as radiation saturation
at high light intensities, and reduced transpiration and photosynthesis as a function of
stomatal closure at high vapour pressure deficits; two important characteristics of dry
tropical environments. This modelling package, which was tested on data on drip-
irrigated tomato grown at various irrigation water salinities in an arid environment, could
also be combined with the data obtained in this project to evaluate the long-term
sustainability of saline water, drip irrigated systems in different environments.
5. Conclusion We conclude that low-cost drip irrigation works well in combination with saline water for
the irrigation of garden crops in semi-arid Africa. Even at quite high irrigation water
salinity (6 dS m−1), a yield above the average marketable yield was reached. Furthermore,
the study showed that the choice of drip irrigation system with regard to discharge rate is
of minor importance when irrigating with saline water. However, combining low-cost
drip irrigation with plastic mulch resulted in a higher yield for all treatments. The choice
of drip system and the inclusion of mulch must be decided upon both from a cost
perspective and from an evaluation of the systems performance in the field, e.g. risk for
blockages. Rainfall had an important role in the leaching of salts from the soils, causing a
openUP (July 2007)
decrease in average soil water salinity of 3–5 dS m−1 over a 4-week period, depending on
treatment. Specific leaf area was found to be higher at high irrigation water salinities,
which contradicts earlier findings (Taleisnik, 1987, Brugnoli and Björkman, 1992 and
Marcelis and van Hooijdonk, 1999). Further, the study showed a higher specific leaf area
for the mulch treatments. Finally, it should be noted that the results of this study are only
valid for the prevailing environmental conditions at the study site. Hence, there is a need
to evaluate the impact of different climates, soils and management practices, as well as
the long-term sustainability of these systems, with a mechanistic modelling approach.
References Barron, 2004 Barron, J., 2004. Dry spell mitigation to upgrade semi-arid rainfed
agriculture: water harvesting and soil nutrient management for smallholder maize
cultivation in Machakos, Kenya. Doctoral Thesis in Natural Resource Management,
Department of Systems Ecology, Stockholm University, Sweden, 39 pp.
Brugnoli and Björkman, 1992 E. Brugnoli and O. Björkman, Growth of cotton under
continuous salinity stress: influence on allocation pattern, stomatal and non-stomatal
components of photosynthesis and dissipation of excess light energy, Planta 187 (1992),
pp. 335–347.
Cardon and Letey, 1992 G.E. Cardon and J. Letey, Soil-based irrigation and salinity
management model: I. Plant water uptake calculation, Soil Sci. Soc. Am. J. 56 (1992), pp.
1881–1887.
Chigerwe et al., 2004 J. Chigerwe, N. Manjengwa, P. van der Zaag, W. Zhakata and J.
Rockström, Low head drip irrigation kits and treadle pumps for smallholder farmers in
Zimbabwe: a technical evaluation based on laboratory tests, Phys. Chem. Earth 29
(2004), pp. 1049–1059.
Chitsiko and Mudima, 2002 Chitsiko, R.J., Mudima, K.T., 2002. Adapting modern
irrigation technologies for use by smallholder farmers—the Zimbabwean experience.
Paper presented at the seminar: “Smallholder Land and Water Management Systems—
Sharing Lessons from Experiences in Africa and Asia”, 1–5 July 2002, Bangkok,
Thailand, 11 pp.
openUP (July 2007)
Daamen et al., 1993 C.C. Daamen, L.P. Simmonds, J.S. Wallace, K.B. Laryea and
M.V.K. Sivakumar, Use of microlysimeters to measure evaporation from sandy soils,
Agr. Forest Meteorol. 65 (1993), pp. 159–173.
Daamen et al., 1995 C.C. Daamen, L.P. Simmonds and M.V.K. Sivakumar, The impact
of sparse millet crops on evaporation from soil in semi-arid Niger, Agric. Water Manage.
27 (1995), pp. 225–242.
Dai et al., 2004 Y. Dai, R.E. Dickinson and Y.-P. Wang, A two-big-leaf model for
canopy temperature, photosynthesis and stomatal conductance, J. Climate 17 (2004) (12),
pp. 2281–2299.
Dasberg and Or, 1999 S. Dasberg and D. Or, Drip Irrigation, Springer-Verlag, Berlin,
Germany (1999) 162 pp.
Du Plessis and Van der Stoep, 2000 Du Plessis, F.J., Van der Stoep, I., 2000. Evaluation
of the appropriateness and management requirements of micro-irrigation in small-scale
farming. Sixth International Micro-Irrigation Congress, “Micro-irrigation Technology for
Developing Agriculture”, Conference Papers, South Africa, 11 pp.
Erenstein, 2002 O. Erenstein, Crop residue mulching in tropical and semi-tropical
countries: an evaluation of residue availability and other technical implications, Soil Till.
Res. 67 (2002), pp. 115–133.
Falkenmark and Rockström, 2004 M. Falkenmark and J. Rockström, Balancing Water for
Humans and Nature: the New Approach in Ecohydrology, EarthScan, London, UK
(2004) 247 pp.
FAO, 2000 FAO, 2000. New dimensions in water security. Lundqvist, J. (Ed.),
AGL/MISC/25/2000, FAO, Rome, Italy, 82 pp.
FAO, 2004 FAO, 2004. A perspective on water control in southern Africa. Support to
regional investment initiatives. Land and water discussion paper 1. Subregional Office
for Southern and East Africa and FAO Land and Water Development Division, FAO,
Rome, Italy, 36 pp.
Farquhar et al., 1980 G.D. Farquhar, S. von Caemmerer and J.A. Berry, A biochemical
model of photosynthetic CO2 assimilation in leaves of C3 species, Planta 149 (1980), pp.
78–90.
openUP (July 2007)
Gary et al., 1993 C. Gary, J.W. Jones and J.J. Longuenesse, Modelling daily changes in
specific leaf area of tomato: the contribution of the leaf assimilate pool, Acta
Horticulturae 328 (1993), pp. 205–210.
Hoffman et al., 1990 G.J. Hoffman, J.D. Rhoades, J. Letey and F. Sheng, Salinity
management. In: G.J. Hoffman, T.A. Howell and K.H. Solomon, Editors, Management of
Farm Irrigation Systems, ASAE Monograph, USA (1990), pp. 667–715.
IFPRI, 2004 IFPRI, 2004. 2003–2004 Annual Report. International Food Policy Research
Institute (IFPRI), Washington, DC, USA, 74 pp.
Kabutha et al., 2000 Kabutha, C., Blank, H., van Koppen, B., 2000. Drip irrigation kits
for small-holder farmers in Kenya: experience and a way forward. Sixth International
Micro-Irrigation Congress, “Micro-irrigation Technology for Developing Agriculture”,
Conference Papers, South Africa, 7 pp.
Karlberg and Penning de Vries, 2004 L. Karlberg and F.W.T. Penning de Vries,
Exploring potentials and constraints of low-cost drip irrigation with saline water in sub-
Saharan Africa, Phys. Chem. Earth 29 (2004), pp. 1035–1042.
Karlberg et al., 2006 L. Karlberg, A. Ben-Gal, P.-E. Jansson and U. Shani, Modelling
transpiration and growth in salinity-stressed tomato under different climatic conditions,
Ecol. Model. 190 (2006), pp. 15–40.
Letey et al., 1985 J. Letey, A. Dinar and K.C. Knapp, Crop-water production function
model for saline irrigation waters, Soil Sci. Soc. Am. J. 49 (1985), pp. 1005–1009.
Marcelis and van Hooijdonk, 1999 L.F.M. Marcelis and J. van Hooijdonk, Effect of
salinity on growth, water use and nutrient use in radish (Raphanus sativus L.), Plant Soil
215 (1999), pp. 57–64.
Marcelis et al., 1998 L.F.M. Marcelis, E. Heuvelink and J. Goudriaan, Modelling
biomass production and yield of horticultural crops: a review, Sci. Horticulturae 74
(1998), pp. 83–111.
Meiri et al., 1992 A. Meiri, H. Frenkel and A. Mantell, Cotton response to water and
salinity under sprinkler and drip irrigation, Agron. J. 84 (1992), pp. 44–50.
Mondal et al., 2001 M.K. Mondal, S.I. Bhuiyan and D.T. Franco, Soil salinity reduction
and prediction of salt dynamics in the coastal ricelands of Bangladesh, Agric. Water
Manage. 47 (2001), pp. 9–23.
openUP (July 2007)
Nimah and Hanks, 1973 M.N. Nimah and R.J. Hanks, Model for estimating soil water,
plant, and atmospheric interrelations: I. Description and sensitivity, Soil Sci. Soc. Am. J.
37 (1973), pp. 522–527.
Pang and Letey, 1998 X.P. Pang and J. Letey, Development and evaluation of ENVIRO-
GRO, an integrated water, salinity and nitrogen model, Soil Sci. Soc. Am. J. 62 (1998),
pp. 1418–1427.
Pasternak and De Malach, 1994 D. Pasternak and Y. De Malach, Crop irrigation with
saline water. In: M. Pessarakli, Editor, Handbook of Plant and Crop Stress, University of
Arizona, Marcel Dekker Inc., New York, U.S. (1994), pp. 599–622.
Postel et al., 2001 S. Postel, P. Polak, F. Gonzales and J. Keller, Drip irrigation for small
farmers. A new initiative to alleviate hunger and poverty, Water Int. 26 (2001) (1), pp. 3–
13.
Rhoades et al., 1992 Rhoades, J.D., Kandiah, A., Mashali, A.M., 1992. The use of saline
waters for crop production. FAO Irrigation and Drainage Paper No. 48, FAO, United
Nations, Rome, 48 pp.
Rockström, 2000 J. Rockström, Water resources management in smallholder farms in
Eastern and Southern Africa: an overview, Phys. Chem. Earth 25 (2000) (3), pp. 279–
288.
Rockström, 2003 J. Rockström, Water for food and nature in the tropics: vapour shift in
rainfed agriculture, Philos. Trans. R. Soc. Lond. B 358 (2003), pp. 1997–2009
Sellers et al., 1996 P.J. Sellers, D.A. Randall, D.A. Collatz, J.A. Berry, C.B. Field, D.A.
Dazlich, C. Zhang, G.D. Collelo and L. Bounoua, A revised land surface
parameterization (SiB2) for Atmospheric GCMs. Part I: model formulation, J. Climate 9
(1996), pp. 676–705.
Sijali, 2001 Sijali, I.V., 2001. Drip irrigation—options for smallholder farmers in eastern
and southern Africa. RELMA Technical Handbook Series 24. Nairobi, Kenya, 60 pp.
Suarez, 1992 D. Suarez, Perspective on irrigation management and salinity, Outlook Agr.
21 (1992) (4), pp. 287–291.
Stoorvogel and Smaling, 1990 Stoorvogel, J.J., Smaling, E.M.A., 1990. Assessment of
soil nutrient depletion in sub-Saharan Africa: 1983–2000, vol. 1: Main Report. Report
No. 28, Winand Staring Centre, Wageningen, The Netherlands.
openUP (July 2007)
Stöckle et al., 2003 C.O. Stöckle, M. Donatelli and R. Nelson, CropSyst, a cropping
systems simulation model, Eur. J. Agronomy 18 (2003), pp. 289–307.
Taleisnik, 1987 E.L. Taleisnik, Salinity effects on growth and carbon balance in
Lycopersicon esculentum and L. pennellii, Physiol. Plantarum 71 (1987), pp. 213–218.
Tesfamariam, 2004 Tesfamariam, E., 2004. Modelling the soil water balance of canola
(Brassica napus L. cv. Hyola 60). M.Sc. Agric. Dissertation, University of Pretoria,
South Africa.
van Dam et al., 1997 van Dam, J.C., Huygen, J., Wesseling, J.G., Feddes, R.A., Kabat,
P., van Walsum, P.E.V., Groenendijk, P., van Diepen, C.A., 1997. Theory of SWAP
Version 2.0. Simulation of water flow, solute transport and plant growth in the soil–
water–atmosphere–plant environment. Report 71, Department of Water Resources,
Wageningen Agricultural University, Technical Document 45, DLO Winard Staring
Centre, The Netherlands, 167 pp.
Corresponding author. Tel.: +46 8 412 14 00; fax: +46 8 723 03 48.
1 The irrigation water from the dam had a salinity level of 0.22 dS m−1. Therefore, the
treatment denoted 0 dS m−1 was in actual fact equal to 0.22 dS m−1, although the former
has been used