20
Copyright DASSAULT SYSTEMES 2002 1 Generative Shape Optimizer CATIA Training Foils Version 5 Release 8 January 2002 EDU-CAT-E-GSO-FF-V5R8
| Date post: | 13-Sep-2015 |
| Category: |
Documents |
| Upload: | svjetlana-bardak |
| View: | 85 times |
| Download: | 20 times |
Copyright DASSAULT SYSTEMES 2002 1
Generative Shape Optimizer
CATIA Training Foils
Version 5 Release 8January 2002
EDU-CAT-E-GSO-FF-V5R8
Copyright DASSAULT SYSTEMES 2002 2
This course covers the Generative Shape Optimizer functions.
Targeted audienceMechanical designers
PrerequisitesCourse WFS, COM, SKE, GSD
Generative Shape Optimizer
0.5 day
Copyright DASSAULT SYSTEMES 2002 3
Table of Contents
Introduction to Generative Shape Optimizer p.4Accessing Generative Shape Optimizer p.5The User Interface p.6
Developing wire p.7 Creating junctions p.10 Creating bumped surfaces p.14 Deforming surfaces according to curve wrapping p.18
Copyright DASSAULT SYSTEMES 2002 4
Introduction to Generative Shape Optimizer
In this lesson you will have an overview of the Generative Shape Optimizer user interface.
Generative Shape Optimizer Workbench Presentation
Copyright DASSAULT SYSTEMES 2002 5
Accessing Generative Shape OptimizerGenerative Shape Optimizer is available through the Generative Shape Design workbench :
Generative Shape Optimizer appears as a tool bar inside the Generative Shape Design workbench : the Advanced Surface toolbar.
Copyright DASSAULT SYSTEMES 2002 6
The User Interface
V5R7
Copyright DASSAULT SYSTEMES 2002 7
Developing Wires
In this lesson, you will learn how to develop wires using the workbench Generative Shape Optimizer.
From a revolution surface into a planeFrom a plane into a revolution surfaceThe wire positioning
Copyright DASSAULT SYSTEMES 2002 8
Developing wires (1)The Develop function can be used to develop a wire lying on a revolution surface into a plane.
Wire to develop
Supporting surface
Copyright DASSAULT SYSTEMES 2002 9
Developing wires (2)Positioning the 2D wire (modifying the wire axis system positioning)
Rotation of the wire axis system positioning
New wire axis system origin
Copyright DASSAULT SYSTEMES 2002 10
Creating Junctions
In this lesson, you will learn how to create a junction surface.
Creating a Junction
Copyright DASSAULT SYSTEMES 2002 11
Creating a Junction (1)
A junction is a surface created between existing curves :
Copyright DASSAULT SYSTEMES 2002 12
Creating a Junction (2)The automatic coupling :
Tangency discontinuities
Curvature discontinuity
Tangency discontinuities detection Curvature discontinuities detection
Copyright DASSAULT SYSTEMES 2002 13
Creating a Junction (3)The manual coupling : Coupling Point
Coupling points
Copyright DASSAULT SYSTEMES 2002 14
Creating a Junction (4)The manual coupling : Coupling Curve
Coupling curve
Copyright DASSAULT SYSTEMES 2002 15
Creating Bumped Surfaces
In this lesson, you learn how to create a bumped surface
Creating a bumped surface
Copyright DASSAULT SYSTEMES 2002 16
Creating a Bumped Surface (1)
A bumped surface is a surface deformed inside a given area :
Copyright DASSAULT SYSTEMES 2002 17
Creating a Bumped Surface (2)Influence of the bumped surface parameters :
1. The continuity type :
Point continuity
Tangent continuity
Curvature continuity
2. The deformation area :
Copyright DASSAULT SYSTEMES 2002 18
Creating a Bumped Surface (3)Influence of the bumped surface parameters :
3. The deformation center :
3. The deformation direction :
Copyright DASSAULT SYSTEMES 2002 19
Deforming surfaces according to curve wrapping In this lesson, you learn how to deform a surface according to curve wrapping
Creating a wrap curve
Copyright DASSAULT SYSTEMES 2002 20
Creating a wrap curve
