3G Analysis using actix

transcript

Remark(before analysising)

1. Once you get the log file ,first check if all the route in the cluster has

been covered,ifnot,the log is useless,tell the DT Teams to test again

2. If you are now using the logs for ATP report ,check if the time reached 4

hours.If not, the log is useless,tell the DT Teams to test again

3. When you are analysisingthe Log file ,make sure you have selected the

right Log files,if the log file is not right ,all the KPI you get is useless.

4. In the bracket of the name of each KPI is the services we need the

pictures.If there are many service ,it means all these services’s pictures is

5. Some pictures and KPIs are together ,we can finish it at the same time to

save our time.

6. The Threshold and the coloer must be the same as the picture.

7. Combine all the logs if there are many logs with the same service.

Here shows how to Combine:

8. Log name: when you get a log ,the name of it may be very long ,so in the

lengend it will be

very long ,it’s not good to see ,such like follow:

So we need to change the log names like this:

Cluster 6 -short call

Cluster 7 –HSDPA short call

It’s short and easy to see

So please rename the log before analysising(if the log with 2 MS,copy 2

with different names)

★★★Drive Route & Collected Samples(Part 3

in report)

Pictures:

Position：

★★★Belows are picture we need:（Part

5/6 in report）

★★★ Total List ★★★：

Servic

Pictures We Need check

Scanne

Best Server 　

RSCP 　

RSCP-Histogram 　

RSCP-Graph 　

EcIo 　

EcIo Histogram 　

EcIo-Graph 　

Best Server 　

RSCP 　

RSCP-Histogram 　

RSCP-Graph 　

EcIo 　

EcIo Histogram 　

EcIo-Graph 　

TxPower 　

Pilot Pollution 　

Active Set Size 　

Droped Call 　

Short Best Server 　

Call-to

Mobile

RSCP 　

RSCP-Histogram 　

RSCP-Graph 　

EcIo 　

EcIo Histogram 　

EcIo-Graph 　

TxPower 　

Pilot Pollution 　

Active Set Size 　

Droped Call 　

Access Failures 　

Best Server 　

RSCP 　

RSCP-Histogram 　

RSCP-Graph 　

EcIo 　

EcIo Histogram 　

EcIo-Graph 　

TxPower 　

Pilot Pollution 　

HSDPA Throughput 　

HSDPA CQI 　

Droped Call 　

Best Server 　

RSCP 　

RSCP-Histogram 　

RSCP-Graph 　

EcIo 　

EcIo Histogram 　

EcIo-Graph 　

TxPower 　

Pilot Pollution 　

HSUPA Throughput 　

Droped Call 　

R99 PS Best Server 　

RSCP 　

RSCP-Histogram 　

RSCP-Graph 　

EcIo 　

EcIo Histogram 　

EcIo-Graph 　

Pilot Pollution 　

R99 Throughput DL 　

R99 Throughput UL 　

Access Failures 　

Droped Call 　

Access Failures 　

Call to

★★★ Example and Notice ★★★

Some other Notice:

1. In the picture, no need to show PSC\NodeB ID\Sector ID, just show the

sites, and the site should be on the front layer.

2. In the picture ,the route should be full-screen,the cluster boundary

\PreDT route should be shown on the map ,don’t show other things.

3. The legend and the color should allow the pictures below.

4. The names of superscream should be like this:

Cluster6-Long Call

Cluster6-Short Call to Mobile

Cluster6-Short Call to PSTN

Cluster6-HSDPA Long

Cluster6-HSUPA Long

Clusetr6-R99

CLuset6-Scanner

Cluster6-HS Short

KPI：Best Server

Snapshot：

Position：

KPI：Best Server(Just for Scanner)

Position：

KPI：RSCP

Snapshot：

Position：

KPI：RSCP -Histogram

Snapshot

Position：

Method ： fill the percentage into the Excel(only the GREEN colum) file

which I send to you，and then the graph will appear automaticly。

automati c generate graph for RSCP and ECNO. zi p

-----this Excel file

KPI : RSCP-Graph

Position：

KPI：RSCP（Just for scanner）

Snapshot：

Position：

KPI：RSCP（Just for scanner）-Histogram

The method as the same as KPI：RSCP-Histogram

KPI：RSCP（Just for scanner）-Graph

The method as the same as KPI：RSCP-Graph

KPI：Ec/Io

Snapshot：

Position：

KPI：Ec/Io –Histogram

For scanner may be different ，ask ZhuJin

Snapshot:

Position：

KPI : Ec/Io –Graph

Position：

KPI：Ec/Io（Just for scanner）

Snapshot:

Position：

KPI：Ec/Io（Just for scanner）-Histogram

The method as the same as KPI：Ec/Io-Histogram

KPI：Ec/Io（Just for scanner）-Graph

The method as the same as KPI：Ec/Io-Graph

KPI：TxPower

Snapshot：

Position：

KPI：Pilot Pollution

Snapshot：

Position：

The definination of PilotPollution:

KPI：Active Set Size

Snapshot：

Position：

KPI：HSDPA Throughtput

Snapshot：

Position：

KPI：R99 Throughtput DL

Snapshot：

Position：

KPI：HSUPA Throughtput

Snapshot：

Position：

KPI：R99 Throughtput UL

Snapshot：

Position：

KPI：HSDPA CQI（DL ）

Snapshot：

Position：

KPI：Access Failures

Snapshot：

Position：

KPI：Droped Call

Snapshot：

Position：

★★★Belows are DT KPIs we need ：（ part

9/10/11 in report）

★★★ Total List ★★★：

Part 9

Information

Element

Mode Total

attempts

Accept

Limit(As Per

SOW) (%)

Accept

Short(

CSV Access

Failure Rate

CS Setup

　 <1.0% Yes 　

*Voice Call

Setup time

(Mobile to

Mobile)

CS Setup

　 95th percentile

≤ 9 seconds

Yes 　

PSD Access

Failure Rate

　 ≤ 1.0 % Yes 　

PSD Drop

　　PS

　 ≤ 1.0 % Yes 　

PSD R99

Average DL

throughput

(kbps) Loaded

　 ≥ 210 Yes 　

PSD R99

Average UL

throughput

(kbps)-

Loaded

　　PS

Calls　

　 ≥ 180 Yes 　

PSD Call

Setup time

　　PS

　 95th percentile

sessions ≤ 3

seconds

Yes 　

Short(

*Voice Call

Setup time

(Mobile to

Calls　

　 95th percentile

≤ 5 seconds

Yes 　

Average UL

（XXXmin

　 > 0.8 Mbps Yes 　

Long Throughput

(kbps) for UE

category 3

under load

HSUPA Drop

　　Time

（XXXmin

　 ≤ 1.0 % 　　

CSV Drop

　Time

（XXXmin

　 <1.0% Yes 　

CSV Quality

　　 95th percentile

of samples ≤

2.0 % BLER

Yes 　

Soft/Softer Setup 　　 <1.6 Yes 　

Handover

Overhead

Average DL

Throughput

(kbps) for UE

category 8

under load

　　 > 2 Mbps Yes 　

HSDPA Drop

　　 ≤ 1.0 % Yes 　

Access Failure

　　 ≤ 1.0 % Yes 　

HSUPA Setup 　　 ≤ 1.0 % Yes 　

Access Failure

Part 10

Information

Element

Mode Total

attempts

Limit(

As Per

Accepta

Comments

Latency-

Stationary

5-DC1 HSPA Ping 1000

percenti

session

s ≤ 100

Yes 　

Stationary

Maximum UL

HSUPA Bit

Rate (kbps)

under no load

(UE Category

　 HSUPA

N/A > 1.2

Yes 　

Stationary

Maximum DL

HSDPA Bit

Rate (kbps)

under no load

(UE Category

　 HSDPA

N/A > 6

Yes 　

Session

　 HS Short Count 95th

percenti

Yes 　

Activation

Statianary

session

second

PSD Latency 5-DC2 PS Ping 1000

percenti

session

s ≤ 100

Yes 　

Part 11

Information

Element

Mode Total

attempts

Limit(

Accepta

Comments

e As Per

CSV Access

Failure Rate

Setup OK

+ Setup

　 / Yes 　

CSV Drop

Complete

　 / Yes 　

KPI：CSV Access Failure Rate–From short call

（Mobile to Mobile）

If this value don’t meet’s our target （1%），Check that if CS Call Setups

>400,if not ,tell me

Position:

Description:

CSV Access Failure= CS Failed Setups / CS Call Setups *100%

Example:

CSV Access Failure = 1/7 *100% = 14.28%

KPI ： *Voice Call Setup time (Mobile to

Mobile)–From Short Call （Mobile to Moble）

Position:

Description:

From RRCConnectionReq to Alerting

Example:

In the picture ,the percent of the time less than 9s is 100%

KPI：PSD Access Failure Rate – PS R99

Position:

Description:

HSDPA Access Failure= PS Failed Setups / PS Call Setups *100%

Example:

HSDPA Access Failure = 0/12 *100% = 0%

KPI：PSD Drop Rate – PS R99

Position:

Decription：

PSD Drop Rate = PS Dropped Calls / PS Successful Calls *100%

Example：

In this picture, PSD Drop Rate = 0/9*100% =0%

KPI：PSD average DLThroughput–From PS-R99

Position:

Open the two workbook,then operate like this:

Description:

Example:

In this picture ,its 285kbps.

KPI ： PSD average UL Throughput–From PS-

Position:

Open the two workbook,then operate like this:

Description:

Example:

In this picture ,it’s 165 kbps.

KPI：PSD Call Setup time–from R99 PS

Position:

Description:

From RRCConnectionReq to PDPActive Complete

Example:

In this picture,the percent of time less than 3s is 99.4%

KPI：Voice Call Setup time (Mobile to PSTN)–

From Short Call (Mobile to PSTN)

Position:

Description:

From RRCConnectionReq to Alerting

Example:

In the picture ,the percent of time less than 5s is 98.8%

KPI ： HSUPA Average UL Throughput –HSUPA

Position:

Decription：

Example：

In this picture, it’s 299.16kbps.

KPI：HSUPA Drop Call Rate–From HSUPA Long

Position:

Here is the time lasts:

Description:

Drop times= 1

The lasting time: from 15:05 to 16:55 ,it’s totally 111 minutes. (make

sure the time is coutinuous, if not ,we need to minus the time it inturrupt)

The HSUPA Drop Rate = Drop times /The lasting time(minute)*1.5

Example:

The HSUPA Drop Rate = 1/111*1.5 = 1.35%

KPI：CSV Drop Rate–From Long call

Position:

Here is the times it droped

Description:

Drop times= 2

The CSV Drop Rate = Drop times /The lasting time(minute)*1.5

Example:

The CSV Drop Rate = 2/111*1.5 = 2.7%

KPI：CSV Quality (DL)–From Long call

Position:

Description:

The BLER which below 2 percent

Example:

In the picture ,the CSV Quality(DL) = 95%

KPI ： Soft/Softer Handover Overhead–From

Longcall

Position:

Description:

Example:

2838*1:(2838 means the point nums of 1 pilot, 1 means that are 1 pilot in

the ActiveSet)

217*2 : (217 means the point nums of 2 pilot, 2 meast that are 2 pilots in

the ActiveSet)

19*3(19 means the point nums of 3 pilot, 3 meast that are 3 pilots in the

ActiveSet)

The Soft/Softer Handover Overhead = (2838*1+217*2+19*3)/

(2838+217+19) = 1.115

KPI ： HSDPA Average DL Throughput –HSDPA

Position:

Decription：

Example：

In this picture ,it’s 309.87kbps

KPI：HSDPA Drop Call Rate–From HSDPA Long

Position:

Description:

Drop times= 1

The HSDPA Drop Rate = Drop times /The lasting time(minute)*1.5

Example:

The HSDPA Drop Rate = 1/111*1.5 = 1.35%

KPI ： HSDPA AccessFailure Rate–From HS

Short Call

Position:

Description:

HSDPA Access Failure= PS Failed Setups / PS Call Setups *100%

Example:

HSDPA Access Failure = 0/12 *100% = 0%

KPI ： HSUPA Access Failure Rate–From HS

Short call （ It’s the same as HSDPA Access

Failure Rate）

Position:

Description:

HSUPA Access Failure= PS Failed Setups / PS Call Setups *100%

Example:

HSUPA Access Failure = 0/12 *100% = 0%

KPI：HSDPA Latency-Stationary

Positon:

Description：

Example:

In this picture,it’s 100%.

KPI：Stationary Maximum UL HSUPA Bit Rate

(kbps) under no load (UE Category 3)

Position:

Example:

In this picture,It’s 1.448Mbps

KPI：Stationary Maximum DL HSDPA Bit Rate

(kbps) under no load (UE Category 8)

Position:

Example:

In this picture,it’s 7.2Mbps.

KPI ： HSDPA Session Activation time-

Statianary

Position:

Example:

KPI：PSD Latency

Positon:

Description：

Example:

KPI：CSV Access Failure Rate-GSM

Position:

Description:

CSV Access Failure Rate = Setup Fail / (Setup OK + Setup Fail) *100%

Example:

In the picture:

CSV Access Failure Rate = 7 / (214 + 7) *100% = 3.2%

KPI：CSV Drop Call Rate-GSM

Position:

Description:

CSV Drop Call Rate = Call Dropped / (Call Complete + Call

Dropped)*100%

Example:

In this picture,it’s 2/(208+2) = 0.95%

★★★UMTS KPI Summary – OSS

Counters:(Part 8 in report)

We need the OSS KPIs like this:

And we will give you the KPI like this: The KPI template：（fill this）

KPI _CL35_CL32_CL7. xl s

OSS KPI Templ ate. xl sx

★★★Uplink Interference Analysis [RTWP]（Part

13 of the report）

We need the Interference KPI like this:

RNCID Cell ID Exist

Interference

Maximu

m Cell

RTWP(db

Average

Cell Freq

RTWP(db

Minimum

Cell Frep

RTWP(db

36 13301 No -86.2 -106.516 -106.8

RNCID Cell ID Exist

Interference

Maximu

m Cell

RTWP(db

Average

Cell Freq

RTWP(db

Minimum

Cell Frep

RTWP(db

36 14062 No -63.7 -

106.3173

36 13151 No -79.2 -

106.4029

-106.6

36 14531 No -81.2 -

106.5058

-106.8

36 14523 No -85.3 -

106.5548

-106.7

And we will give you the KPI like this: The KPI template：（fill this）

KPI _CL35_CL32_CL7. xl s

I nterference Anal ysi s KPI . xl sx

Belows are Drop Call List we

List of Dropped Calls

# SITE

Reason Action Taken Problem

Solved

We can find the call drops in the pictures below:

In this picture we can find which site it droped .

If you want to know the reason,see the signal .

3G Analysis using actix

Documents