Post on 02-Jun-2018
transcript
8/10/2019 Active Disturbance Rejection
1/34
Electronics2013,2, 246-279; doi:10.3390/electronics2030246OPEN ACCESS
electronicsISSN 2079-9292
www.mdpi.com/journal/electronicsArticle
A Simulative Study on Active Disturbance Rejection Control
(ADRC) as a Control Tool for Practitioners
Gernot Herbst
Siemens AG, Clemens-Winkler-Strae 3, Chemnitz 09116, Germany;
E-Mail: gernot.herbst@siemens.com; Tel.: +49-371-475-2883.
Received: 20 May 2013; in revised form: 27 June 2013 / Accepted: 22 July 2013 /
Published: 15 August 2013
Abstract: As an alternative to both classical PID-type and modern model-based approaches
to solving control problems, active disturbance rejection control (ADRC) has gained
significant traction in recent years. With its simple tuning method and robustness against
process parameter variations, it puts itself forward as a valuable addition to the toolbox of
control engineering practitioners. This article aims at providing a single-source introduction
and reference to linear ADRC with this audience in mind. A simulative study is carried
out using generic first- and second-order plants to enable a quick visual assessment of the
abilities of ADRC. Finally, a modified form of the discrete-time case is introduced to speed
up real-time implementations as necessary in applications with high dynamic requirements.
Keywords:active disturbance rejection control (ADRC); extended state observer (ESO)
1. Introduction
Active disturbance rejection control (ADRC) [14] has emerged as an alternative that combines easy
applicability known from classical PID-type control methods with the power of modern model-based
approaches. The foundation for ADRC is an observer who jointly treats actual disturbances and
modeling uncertainties, such that only a very coarse process model is necessary in order to design a
control loop, which makes ADRC an attractive choice for practitioners and promises good robustness
against process variations. Present applications range from power electronics [5], motion control [6] and
superconducting radio frequency cavities [7] to tension and temperature control [8].
While it can be shown (cf. Section2.3) that the linear case of ADRC is equivalent to a special case of
classical state space control with disturbance estimation and compensation based on the internal model
8/10/2019 Active Disturbance Rejection
2/34
Electronics2013,2 247
principle [9], there is an important difference to model-based approaches, such as model predictive
control [10] or embedded model control [11]: for the latter, an explicit model of the process to be
controlled is necessary. ADRC, on the other hand, does only assume a certain canonical model regardless
of the actual process dynamics and leaves all modeling errors to be handled as a disturbance. Ofcourse this may come at the price of performance losses compared to a controller built around a precise
process model or a model of the reference trajectory. Therefore, while employing the same mathematical
tools, ADRCs unified view and treatment of disturbances can be seen as a certain departure from the
model-based control school [12], shifting back the focus from modeling to control. This may be key to
its appeal for practitioners.
The remainder of this article is organized as follows: After providing a step-by-step introduction
to the linear case of ADRC in the following section, a series of simulative experiments is carried out
to demonstrate the abilities of ADRC when being faced with varying process parameters or structural
uncertainties and to visually provide insights into the effect of its tuning parameters. For the discrete-timecase, which is introduced afterwards, an optimized formulation is presented, which enables a controller
implementation with very low input-output delay.
2. Linear Active Disturbance Rejection Control
The aim of this section is to repeat and present the linear case of ADRC in a self-contained
manner, following [3,13]. While the majority of articles introduces ADRC with a second-order process,
here the first-order case will be considered first and explicitly, due to its practical importance, since
there are many systemsalbeit technically nonlinear and higher-orderwhich exhibit a dominatingfirst-order-like behavior, at least in certain operating points. The second-order case will be developed
subsequently with a similar use case in mind. Additionally, it will be shown in Section2.3 that linear
ADRC can be seen as a special case from the perspective of classical state space control with disturbance
compensation based on the internal model principle.
2.1. First-Order ADRC
Consider a simple first-order process,P(s), with a DC gain,K, and a time constant, T:
P(s) = y(s)u(s)
= KT s + 1
T y(t) +y(t) =Ku(t) (1)
We add an input disturbance, d(t), to the process, abbreviateb= KT
and rearrange:
y(t) = 1
T y(t) +
1
T d(t) +
K
T u(t) =
1
T y(t) +
1
T d(t) + b u(t)
As our last modeling step, we substituteb = b0 +b, whereb0shall represent the known part ofb = KT
and b, an (unknown) modeling error, and, finally, obtain Equation (2). We will see soon that all that we
need to know about our first-order process to design an ADRC is b0 b, i.e., an approximate value ofK
T. Modeling errors or varying process parameters are represented by band will be handled internally.
y(t) =
1
T y(t) +
1
T d(t) +b u(t)
generalized disturbancef(t)
+b0 u(t) = f(t) + b0 u(t) (2)
8/10/2019 Active Disturbance Rejection
3/34
Electronics2013,2 248
By combining 1Ty(t), the disturbanced(t), and the unknown part b u(t)to a so-called generalized
disturbance, f(t), the model for our process changed from a first-order low-pass type to an integrator.
The fundamental idea of ADRC is to implement an extended state observer (ESO) that provides an
estimate, f(t), such that we can compensate the impact of f(t) on our process (model) by means of
disturbance rejection. All that remains to be handled by the actual controller will then be a process with
approximately integrating behavior, which can easily be done, e.g. by means of a simple proportional
controller.
In order to derive the estimator, a state space description of the disturbed process in Equation (2)
is necessary: x1(t)
x2(t)
=
0 1
0 0
A
x1(t)
x2(t)
+
b0
0
Bu(t) +
0
1
f(t)
y(t) =
1 0
C
x1(t)
x2(t)
(3)
Since the virtual input, f(t), cannot be measured, a state observer for this kind of process can, of
course, only be built using the input, u(t), and output, y(t), of the process. An estimated state, x2(t),
however, will provide an approximate value of f(t), i.e., f(t), if the actual generalized disturbance,
f(t), can be considered piecewise constant. The equations for the extended state observer (integrator
process extended by a generalized disturbance) are given in Equation (4). Note that for linear ADRC,
a Luenberger observer is being used, while in the original case of ADRC, a nonlinear observer was
employed [4]. x1(t)x2(t)
=
0 1
0 0
x1(t)
x2(t)
+
b0
0
u(t) +
l1
l2
(y(t) x1(t))
=
l1 1
l2 0
ALC
x1(t)
x2(t)
+
b0
0
B
u(t) +
l1
l2
L
y(t)(4)
One can now use the estimated variables, x1(t) = y(t)and x2(t) = f(t), to implement the disturbancerejection and the actual controller.
u(t) =u0(t) f(t)
b0with u0(t) =KP (r(t) y(t)) (5)
The according structure of the control loop is presented in Figure 1.SinceKPacts on y(t), rather than
the actual outputy(t), we do have a estimation-based state feedback controller, but the resemblance to a
classical proportional controller is striking to practitioners. In Equation (5), u0(t)represents the output
of a linear proportional controller. The remainder of the control law in u(t)is chosen such that the linear
controller acts on a normalized integrator process if f(t) f(t)holds. The effect can be seen by putting
Equation (5) in Equation (2):
y(t) = f(t) + b0 u0(t) f(t)
b0=
f(t) f(t)
+ u0(t) u0(t) =KP (r(t) y(t))
8/10/2019 Active Disturbance Rejection
4/34
Electronics2013,2 249
Figure 1. Control loop structure with ADRC for a first-order process.
ProcessKP1
b0
1
b0
Observer
u yr
y = x1
f = x2
u0
If y(t) y(t)holds, we obtain a first-order closed loop behavior with a pole,sCL = KP:
1
KP y(t) +y(t)
1
KP y(t) +y(t) r(t)
If the state estimator and disturbance rejection work properly, one has to design a proportional
controller only one single time to obtain the same closed loop behavior, regardless of the parametersof the actual process. For example, one can calculate KP from a desired first-order system with
2%-settling time:
KP 4
Tsettle(6)
In order to work properly, observer parameters, l1 and l2, in Equation (4) still have to be determined.
Since the observer dynamics must be fast enough, the observer poles, sESO1/2 , must be placed left of the
closed loop pole,sCL. A simple rule of thumb suggests for both poles:
sESO
1/2
=sESO (3 . . . 10) sCL with sCL = KP 4
Tsettle(7)
Placing all observer poles at one location is also known as bandwidth parameterization [3]. Since
the matrix (A LC) determines the error dynamics of the observer, we can compute the necessary
observer gains for the common pole location, sESO, from its characteristic polynomial:
det(sI (ALC)) =s2 + l1 s + l2!
=
s sESO2
=s22sESO s +
sESO2
From this equation, the solutions forl1and l2can immediately be read off:
l1= 2 s
ESO
and l2= sESO2 (8)To summarize, in order to implement a linear ADRC for a first-order system, four steps are necessary:
1. Modeling: For a process with (dominating) first-order behavior, P(s) = K
T s + 1, all that needs to
be known is an estimate b0 KT
.
2. Control structure: Implement a proportional controller with disturbance rejection and an extended
state observer, as given in Equations (4) and (5):
x1(t)
x2(t)=l1 1
l2 0 x1(t)
x2(t)+b0
0 u(t) +l1
l2 y(t)u(t) =
KP (r(t) y(t)) f(t)
b0=
KP (r(t) x1(t)) x2(t)
b0
8/10/2019 Active Disturbance Rejection
5/34
Electronics2013,2 250
3. Closed loop dynamics: ChooseKP, e.g. according to a desired settling time Equation (6):
KP 4
Tsettle.
4. Observer dynamics: Place the observer poles left of the closed loop pole via Equations (7) and (8):
l1= 2 sESO, l2= sESO2 with sESO (3 . . . 10) sCL and sCL = KPIt should be noted that the same control structure can be applied to a first-order integrating process:
P(s) =y(s)
u(s)=
KI
s y(t) =KI u(t)
With an input disturbance, d(t), and a substitution, KI = b= b0+ b, with b representing the
unknown part ofKI, we can model the process in an identical manner as Equation (2), with all differences
hidden in the generalized disturbance, f(t):
y(t) = (d(t) +b u(t)) gen. disturbancef(t)
+b0 u(t) = f(t) + b0 u(t)
Therefore, the design of the ADRC for a first-order integrating process can follow the same four
design steps given above, with the only distinction thatb0must be set to b0 KIin step 1.
2.2. Second-Order ADRC
Following the previous section, we now consider a second-order process, P(s), with a DC gain, K,
damping factor,D, and a time constant, T.
P(s) =y(s)
u(s)=
K
T2s2 + 2DT s + 1 T2 y(t) + 2DT y(t) +y(t) =Ku(t) (9)
As for the first-order case, we add an input disturbance, d(t), abbreviate b= KT2
and split b into a
known and unknown part,b=b0+b:
y(t) =
2D
T y(t)
1
T2y(t) +
1
T2d(t) +b u(t)
generalized disturbancef(t)
+b0 u(t) = f(t) + b0 u(t) (10)
With everything else combined into the generalized disturbance, f(t), all that remains of the process
model is a double integrator. The state space representation of the disturbed double integrator is: x1(t)x2(t)x3(t)
=0 1 00 0 1
0 0 0
A
x1(t)x2(t)x3(t)
+ 0b0
0
B
u(t) +
001
f(t)
y(t) =
1 0 0
C
x1(t)x2(t)
x3(t)
(11)
8/10/2019 Active Disturbance Rejection
6/34
Electronics2013,2 251
Figure 2. Control loop structure with active disturbance rejection control (ADRC) for a
second-order process.
ProcessKP1
b0
1
b0
Observer
u yr
y = x1
f = x3
u0
KD
y = x2
In order to employ a control law similar to the first-order case, an extended state observer is needed
to provide an estimation, x1(t) = y(t), x2(t) = y(t)and x3(t) = f(t):
x1(t)x2(t)x3(t)
=0 1 0
0 0 10 0 0
x1(t)
x2(t)x3(t)
+0
b00 u(t) +
l1
l2l3 (y(t) x1(t))
=
l1 1 0l2 0 1l3 0 0
ALC
x1(t)x2(t)x3(t)
+ 0b0
0
B
u(t) +
l1l2l3
L
y(t)
(12)
Using the estimated variables, one can implement the disturbance rejection and a linear controller
for the remaining double integrator behavior, as shown in Figure2. A modified PD controller (without
the derivative part for the reference value r(t)) will lead to a second-order closed loop behavior withadjustable dynamics. Again, this actually is an estimation-based state feedback controller.
u(t) =u0(t) f(t)
b0with u0(t) =KP (r(t) y(t))KD y(t) (13)
Provided the estimator delivers good estimates, x1(t) = y(t) y(t), x2(t) = y(t) y(t) and
x3(t) = f(t) f(t), one obtains after inserting Equation (13) into Equation (10):
y(t) =
f(t) f(t)
+ u0(t) u0(t) KP (r(t)y(t))KD y(t)
Under ideal conditions, this leads to:
1
KP y(t) +
KD
KP y(t) +y(t) =r(t)
While any second-order dynamics can be set using KP andKD, one practical approach is to tune the
closed loop to a critically damped behavior and a desired 2% settling time Tsettle,i.e., chooseKP and KD
to get a negative-real double pole,sCL1/2=s
CL:
KP=
sCL
2
and KD= 2 sCL with sCL
6
Tsettle(14)
Similar to the first order case, the placement of the observer poles can follow a common rule of thumb:
sESO1/2/3=sESO (3 . . . 10) sCL with sCL
6
Tsettle(15)
8/10/2019 Active Disturbance Rejection
7/34
Electronics2013,2 252
Once the pole locations are chosen in this manner, the observer gains are computed from the
characteristic polynomial of(ALC):
det(sI (ALC)) =s3 + l1 s2 + l2 s + l3
!= s sESO
3=s3 3sESO s2 + 3 sESO
2 ssESO
3
The respective solutions forl1,l2and l3are:
l1= 3 sESO, l2=3
sESO
2and l3=
sESO
3(16)
To summarize, ADRC for a second-order system is designed and implemented as follows:
1. Modeling: For a process with (dominating) second-order behavior,P(s) = K
T2s2 + 2DT s + 1, one
only needs to know an approximate value b0 KT2
.
2. Control structure: Implement a proportional controller with disturbance rejection and an extendedstate observer, as given in Equations (12) and (13): x1(t)x2(t)
x3(t)
=l1 1 0l2 0 1l3 0 0
x1(t)x2(t)
x3(t)
+ 0b0
0
u(t) +l1l2
l3
y(t)u(t) =
KP (r(t) y(t))KD y(t)
f(t)
b0=
(KP (r(t) x1(t))KD x2(t)) x3(t)
b0
3. Closed loop dynamics: Choose KP and KD, e.g. according to a desired settling time as given in
Equation (14):KP=
sCL2
, KD= 2 sCL with sCL
6
Tsettle
4. Observer dynamics: Place the observer poles left of the closed loop poles via Equations (15)
and (16):
l1= 3 sESO, l2=3
sESO
2, l3=
sESO
3with sESO (3 . . . 10) sCL
2.3. Relation to Linear State Space Control with Disturbance Estimation and Compensation
Given that linear ADRC only employs tools known from classical linear state space control, how can
it be compared to existing approaches? In this section, we will demonstrate that linear ADRC can be
related to state space control with disturbance estimation and compensation based on the internal model
principle [9]. We will start with a linear state space model of a process disturbed by d(t), as follows:
x(t) =Ax(t) +Bu(t) +Ed(t), y(t) = Cx(t) (17)
Further, we assume to possess a model for the generation of the disturbance, d(t):
xd(t) =Adxd(t), d(t) = Cdxd(t) (18)
Note thatAd andCdin Equation (18) refer to modeling the disturbance generator in this section only
and should not be mistaken for the discrete-time versions ofA andCused in Section4. The process
model is now being extended by incorporating the internal state variables, xd(t), of the disturbance
8/10/2019 Active Disturbance Rejection
8/34
Electronics2013,2 253
generator, resulting in an augmented process model in Equation (19), for which an observer given in
Equation (20) can be set up [14]:
x(t)xd(t)=A ECd0 Ad x(t)xd(t)+B0 u(t), y(t) = C 0 x(t)xd(t) (19) x(t)xd(t)
=
A ECd
0 Ad
A
x(t)
xd(t)
+
B
0
B
u(t) +
L
Ld
L
y(t)
C 0
C
x(t)
xd(t)
(20)
Accordingly, the standard state space control law can now be enhanced by the estimated state variables
of the disturbance generator in order to compensate or minimize the impact of the disturbance on the
process, if a suitable feedback matrix, Kd, can be found:
u(t) =G r(t)K x(t)Kd xd(t) (21)
After inserting Equation (21) into Equation (17), it becomes apparent thatprovided an accurate
estimation, xd(t), is availablethe disturbance may be compensated to the extent that BKd= ECd can
be satisfied [14].
We will now compare the combined state and disturbance observer based on the augmented process
model, as well as the control law to linear ADRC presented before. The first- and second-order case will
be distinguished by (a) and (b):
Process model and disturbance generator: When comparing Equations (20) to (4) and (12),
respectively, one obtains the (double) integrator process with a constant disturbance model. The
respective matricesEcan be found using Equations (2) and (10):
(a) A=0, B=b0, C=1, E= 1T
, Ad=0, Cd= T= Kb0
(b) A=
0 1
0 0
, B=
0
b0
, C=
1 0
, E=
01
T2
, Ad=0, Cd= T
2 = Kb0
Control law: The comparison of Equations (5) and (21) or (13) can be made with f= xdbeing the
estimated state of the disturbance generator:
(a)
1
b0 KP (r(t) y(t)) f(t)= KPb0 r(t) KPb0 x1(t) 1b0 f(t)gives: Kd=
1
b0, K= K1=
KP
b0, G=
KP
b0=K1
(b) 1
b0
KP (r(t) y(t))KD y(t) f(t)
=KP
b0 r(t)
KP
b0 x1(t)
KD
b0 x2(t)
1
b0 f(t)
gives: Kd= 1
b0, K=
K1 K2
with K1=
KP
b0,K2=
KD
b0, G=
KP
b0=K1
One can see that the observer and control law are equivalent in structure for both linear ADRC and a
state space approach based on the internal model principle, and the model of the disturbance generator
in ADRC could be made more visible by this comparison. If the standard design procedure of a statespace observer and controller with disturbance compensation will lead to the same parameter values as
ADRC will be verified subsequently by following the necessary steps to design K,Kd,G and Lbased onthe same design goals used in linear ADRC before:
8/10/2019 Active Disturbance Rejection
9/34
Electronics2013,2 254
Feedback gain K: The closed loop dynamics are determined by the eigenvalues of(ABK). For
ADRC, all poles were placed on one location,sCL. With this design goal, one obtains for K:
(a) det (sI (ABK)) !=s sCL gives K1=
sCL
b0
(b) det (sI (ABK)) !=
s sCL2
gives K1=
sCL2
b0and K2=
2sCL
b0
Gain compensation G: In order to eliminate steady state tracking errors, G must be chosen to
G=
C (ABK)1 B1
, which givesG=K1for both the first- and second-order case.
Observer gainL: The dynamics of the observer for the augmented system are determined byplacing the eigenvalues of
ALC as desired, which is the identical procedure, as in Equations(8) and (16).
Disturbance compensation gain Kd: As mentioned above, Kd should be chosen to achieve
BKd !=ECdif possible:
(a) BKd=b0 Kd!
=ECd=1 gives Kd= 1
b0
(b) BKd=
0
b0 Kd
!=ECd
0
1
gives Kd=
1
b0
Obviously, both designs deliver the same parameters. Based on this comparison, one may view
linear ADRC and its controller design as a special case of classical state space control with an observer
using a system model augmented by a certain disturbance generator model (following the internal model
principle) and disturbance compensation. However, a subtle, but important, distinction has to be made:while the latter relies on a model of the plant (like all modern model-based control approaches), ADRC
does always deliberately assume an integrator model for the plant and leaves all modeling errors to be
handled by the disturbance estimation. Therefore, ADRC can be applied without accurately modeling
the process, which presents a departure from the model-based control school [ 12].
3. Simulative Experiments
In the ideal casewith noise-free measurements and unlimited, ideal actuators in the control
loopADRC would be able to suppress basically all effects of disturbances and parameter variations ofthe process. In practice, however, we have to live with constraints, such as limited observer dynamics or
saturated controller outputs, leading to a compromise when choosing the parameters of the controller.
This section is meant to provide insights into the abilities and limitations of continuous-time ADRC in
a visual manner. To that end, the controllerdesigned once and then left unchangedwill be confronted
with a heavily varying process. The influence of the ESO pole placement (relative to the closed loop
poles) will also be examined, as well as limitations of the actuator. The experiments are carried out by
means of Matlab/Simulink-based simulations.
In Section4.2,further simulations will be performed for the discrete-time implementation of ADRC,
also addressing the effect of noise and sampling time.
8/10/2019 Active Disturbance Rejection
10/34
Electronics2013,2 255
3.1. First-Order ADRC with a First-Order Process
In a first series of experiments, a continuous-time ADRC (as introduced in Section2.1) operating on
a first-order system will be examined. The process structure and nominal parameters used to design the
controller are:
P(s) =y(s)
u(s)=
K
T s + 1 with K=1 and T=1
The ADRC is designed following the four steps described in Section 2.1. For now, we assume perfect
knowledge of our process and set b0= KT
=1, but will leave this value unchanged for the rest of the
experiments in this section. The desired closed loop settling time is chosen, Tsettle= 1. To this end, the
proportional gain of the linear controller is, according to Equation (6), set to KP= 4Tsettle
=4. Unless
otherwise noted in individual experiments, the observer poles are chosen be sESO1/2 =s
ESO =10 sCL =
10 (KP) = 40. The respective values of the observer gains are obtained via Equation ( 8).
Throughout Section 3.1, noise-free control variables and ideal measurements will be assumed.
Reaction on noisy measurements will be part of further experiments in Section4.2.
3.1.1. Sensitivity to Process Parameter Variations
Given the explicit feature of ADRC to cope with modeling errors, our first goal will be to provide
visual insights into the control loop behavior under (heavy) variations of process parameters. A series of
simulations was run with fixed ADRC parameters as given above and a first-order process with varying
parameters,K(DC gain) andT(time constant). In Figure3,the closed loop step responses are displayed
on the left- and the according controller outputs on the right-hand side. For bothKandT, values were
chosen from an interval reaching from 10% of the nominal value to 1000%, i.e., a decrease and increase
by factors up to ten.
The results are quite impressive. One can see that the closed loop step response remains similar
or nearly identical to the desired behavior (settling time of one second) for most process parameter
settings in Figure3. Almost only for the five- and ten-fold increased time constant, larger overshoots
become visible. In theory, ideal behavior (i.e., almost complete ignorance of parameter variations) can
be obtained by placing the observer poles far enough to the left of the closed loop poles, as will be shown
in Section3.1.2.Note that we are not constrained by actuator saturation here; this case will be examined
in Section3.1.3.
3.1.2. Effect of Observer Pole Locations
In the previous Section3.1.1, the observer poles were placed ten times faster than the closed loop
pole (sESO1/2
=sESO =10 sCL). How does the choice of this factor influence the behavior and abilities
regarding process parameter variations? We will repeat the simulations with varying time constant, T,
of process both with slower and faster observers. To demonstrate a rather extreme case, as well, we will,
for the faster setting, apply a factor ofsESO =100 sCL.
The results in Figure4are ordered from fastest (top) to slowest observer setting (bottom). For the
fastest setting, the theoretical ability to almost completely ignore any modeling error is confirmed. In
order to achieve this behavior in practice, the actuator must be fast enough and must not saturate within
8/10/2019 Active Disturbance Rejection
11/34
Electronics2013,2 256
Figure 3. Experiment 3.1.1: fixed first-order ADRC controlling first-order process with
varying parameters. Nominal process parameters: K= 1, T = 1. ADRC parameters:
b0= KT
=1, Tsettle = 1, sESO = 10 sCL. (a) Variation of K, closed loop step response;
(b) Controller outputu for (a); (c) Variation ofT, closed loop step response; (d) Controlleroutput u for (c).
0 0.5 1 1.5 2 2.5 30
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5K = 10
(a)
0 0.5 1 1.5 2 2.5 35
0
5
10
15
20
t
u
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
K = 10
(b)
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2T = 0.5
T = 2
T = 5
T = 10
(c)
0 0.5 1 1.5 25
0
5
10
15
20
t
u
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5T = 10
(d)
the desired range of parameter variations. For slower observer settings, the actual closed loop dynamics
increasingly differ from the desired dynamics, noticeable especially from larger overshoots for process
variations with stronger low-pass character.
3.1.3. Effect of Actuator Saturation
In practice, the abilities of any controller are tied to limitations of the actuator,i.e., its dynamics and
the realizable range of values of the actuating variable. While the actuator dynamics can be viewed
as part of the process dynamics during controller design, one has to take possible effects of actuator
saturation into account.
If parameters of our example process change, the control loop behavior may be influenced or limited
by actuator saturation in different ways: If the process becomes slower (i.e., the time constant T
increases), actuator saturation will increase the settling time. If, on the other hand, the DC gain of
8/10/2019 Active Disturbance Rejection
12/34
Electronics2013,2 257
Figure 4. Experiment3.1.2: effect of pole locations for the extended state observer (ESO) on
a fixed first-order ADRC controlling first-order process with varying parameter, T. Nominal
process parameters: K=1,T=1. ADRC parameters: b0= KT =1,Tsettle=1,sESO varying.(a) Closed loop step response, sESO =100 sCL; (b) Controller output ufor (a); (c) Closed
loop step response, sESO =10 sCL; (d) Controller output u for (c); (e) Closed loop step
response, sESO =5 sCL; (f) Controller outputu for (e).
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(a)
0 0.5 1 1.5 210
0
10
20
30
40
t
u
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5T = 10
(b)
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(c)
0 0.5 1 1.5 25
0
5
10
15
20
t
u
T = 1
T = 0.1
T = 0.2T = 0.5
T = 2
T = 5
T = 10
(d)
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(e)
0 0.5 1 1.5 25
0
5
10
15
t
u
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(f)
8/10/2019 Active Disturbance Rejection
13/34
Electronics2013,2 258
Figure 5. Control loop structure of first-order ADRC considering actuator saturation.
ProcessKP1
b0
1
b0
Observer
ulim yr
y= x1
f = x2
u0 u
Actuator
model
Figure 6. Experiment3.1.3: effect of actuator saturation, |ulim| 5, on fixed a first-order
ADRC controlling first-order process with varying parameters. Nominal process parameters:
K=1,T=1. ADRC parameters: b0= KT
=1,Tsettle=1,sESO =10 sCL. On the right-hand
side, the controller outputs are shown before the limitation (dashed line) takes effect. (a)
Variation ofK, closed loop step response; (b) Controller outputu for (a); (c) Variation ofT,
closed loop step response; (d) Controller outputu for (c).
0 0.5 1 1.5 2 2.5 30
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
K = 10
(a)
0 0.5 1 1.5 2 2.5 32
0
2
4
6
8
10
t
u
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
K = 10
(b)
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(c)
0 0.5 1 1.5 22
0
2
4
6
8
10
t
u
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(d)
the process decreases, the control loop may be not be able to reach the reference value under actuator
saturation.
In classical PID-type control, some sort of anti-windup strategy would be required to prevent the
side-effects of actuator saturation. We will see in the experiments of this section that for ADRC, those
effects can be overcome very simply by feeding the state observer with the limited actuating variable,
ulim(t), instead ofu(t), either by a measured value or by an actuator model, cf. Figure5.
8/10/2019 Active Disturbance Rejection
14/34
8/10/2019 Active Disturbance Rejection
15/34
Electronics2013,2 260
Figure 8. Experiment 3.1.5: effect of structural uncertainties on a first-order ADRC
controlling a process with dominating first-order behavior (K= 1, T=1) and higher-order
dynamics caused by an unknown second pole ats= 1/T2. ADRC parameters: b0= KT
=1,
Tsettle= 1,sESO
= 2 sCL
. (a) Variation ofT2, closed loop step response; (b) Controller outputufor (a).
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T2= 0.001
T2= 0.01
T2= 0.05
T2= 0.1
(a)
0 0.5 1 1.5 20
1
2
3
4
t
u
T2= 0.001
T2= 0.01
T2= 0.05
T2= 0.1
(b)
3.1.4. Effect of Dead Time
Many practical processes with dominating first-order behavior do exhibit a dead time. While there are
many specialized model-based approaches to control such processes, we are interested in how ADRC
will handle an unknownalbeit smallamount of dead time in the control loop.
In Figure 7, simulations were performed as in previous experiments, and a dead time, Tdead, was
added to the process with Tdead 0.1, i.e., up to 10 %, compared to the time constant, T, of the
process. As expected, oscillations are inevitably starting to appear with increasing Tdead, especially
in the controller output. However, this situation can be improved if the dead time of the process isat
least approximatelyknown. An easy way of incorporating small dead times into ADRC can be found
by delaying the controller output fed into the observer by TESOdead, i.e., usingu(tTESO
dead) instead ofu(t)
in Equation (4). In Figure7(c)and(d), this approach was implemented using TESOdead =0.05. Clearly, the
oscillations in the controller output are less prominent, even ifTESO
deaddoes not match the actual dead time.
3.1.5. Effect of Structural Uncertainties
In the experiments carried out so far in this section, it was assumed that our process could be
reasonably well described by a first-order model. In practice, such a first-order model almost always
results from neglecting higher-order dynamics, e.g. of the actuator. While it could already be seen that
ADRC can handle variations of parameters very well, how does it behave if higher-order dynamics
become unexpectedly visible in the process?
To demonstrate this behavior, a second pole was added to the process in the simulations from Figure8,
resulting in a second time constant, T2 0.1, i.e., up to 10% of the dominant time constant, T. One
can see that some oscillations start to appear during the transient as the higher-order pole approaches
the dominant pole. While these results are acceptable, further simulations showed that ADRC did not
8/10/2019 Active Disturbance Rejection
16/34
Electronics2013,2 261
Figure 9. Experiment 3.1.6: comparison of first-order ADRC and PI controller faced
with varying process parameters, K and T. Nominal process and ADRC parameters are
as throughout Section3.1. For each combination, the closed loop step response is shown.
(a) Variation ofK, ADRC; (b) Variation ofK, PI; (c) Variation ofT, ADRC; (d) VariationofT, PI.
0 0.5 1 1.5 2 2.5 30
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
K = 10
(a)
0 0.5 1 1.5 2 2.5 30
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
K = 10
(b)
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(c)
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.1
T = 0.2
T = 0.5
T = 2
T = 5
T = 10
(d)
provide an advantage comparing to standard PI controllers as large as it does in the case of parameter
robustness, cf. Section3.1.6.
3.1.6. Comparison to PI Control
Given the ubiquity of PID-type controllers in industrial practice, how does the standard approach
keep up against ADRC? To that end, we will repeat the experiment regarding sensitivity towards process
parameter variations and compare the ADRC results to a PI controller.
For the first-order process, a PI controller is sufficient to achieve any desired first-order closed loop
behavior. In order to obtain comparable results, the PI controller is designed for nearly identical closed
loop dynamics as the ADRC by aiming for the same settling time and placing a zero on the pole of the
first-order process:
CPI(s) =KP+KI
s with KI=
3.85
KTsettle=3.85 and KP=KI T=3.85
8/10/2019 Active Disturbance Rejection
17/34
Electronics2013,2 262
Figure 10. Experiment 3.1.7: comparison of disturbance rejection behavior (first-order
ADRC vs. PI controller). Process and ADRC parameters are as throughout Section 3.1.
Input disturbance,d=1, was effective fromt=2 untilt=4. (a) Step response and reaction
on disturbance; (b) Controller outputu for (a).
0 1 2 3 4 5 60
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
ADRC
PI
(a)
0 1 2 3 4 5 61
0
1
2
3
4
t
u
ADRC
PI
(b)
The simulation results in Figure 9 clearly demonstrate the ability of the ADRC approach to keep
the closed loop dynamics similar, even under major parameter variations. The PI controller delivers
dynamics that vary heavily, as do the process parameters.
3.1.7. Disturbance Rejection of ADRC and PI
As a final experiment for the continuous-time first-order ADRC, we want to examine the disturbance
rejection abilities by injecting an input disturbance into the process for both ADRC and the PI controller
from Section3.1.6.
On the left-hand side of Figure10, a closed loop step response is shown. The input disturbance is
effective during the period from t= 2 until t= 4. While both controllers were tuned for the same reaction
on setpoint changes, the impact of the disturbance is compensated for much faster by ADRC compared
to the PI controller. In classical control, one would need to tune the PI controller much more aggressively
and add a setpoint filter or follow another 2DOF approach in order to obtain similar results [ 15].
3.2. Second-Order ADRC with a Second-Order Process
The second-order ADRC will be examined using a second-order process with the following
nominal parameters:
P(s) =y(s)
u(s)=
K
T2s + 2DT s + 1 with K=1, D=1 and T=1
Again, perfect knowledge of the process is assumed, b0 = KT2
=1, but then b0 is left unchanged
throughout Section 3.2. The desired closed loop settling time is Tsettle =5. The parameters of the
PD controller are, following Equation (14), set to KP=
6Tsettle
2=1.44 and KD=
12Tsettle
=2.4. Unless
otherwise noted in individual experiments, the observer poles are chosen to besESO1/2/3= s
ESO = 10 sCL =
8/10/2019 Active Disturbance Rejection
18/34
Electronics2013,2 263
10 6
Tsettle
= 12. The respective values of the observer gains,l1/2/3, are obtained via Equation (16).
As in Section 3.1, throughout this section, noise-free control variables and ideal measurements will
be assumed.
3.2.1. Sensitivity to Process Parameter Variations
For the second-order ADRC, sensitivity to variations of the process parameters will be examined
firstly. Deviations from the original DC gain (K= 1) were made in a range of 10% to 500% by setting
Kto one of the values 0.1, 0.2, 0.5, 2 and 5. The damping factor,D, of the process was varied within a
range of 10% to 1000% of the original value, D= 1, using settings 0.1, 0.2, 0.5, 2, 5 and 10. Finally,
the time constant, T, of the second-order process was varied in a range of 50% to 350% of the original
value,T=1, using the values 0.5, 2, 3 and 3.5.
From the results in Figure11,one can see that the closed loop behavior is almost not at all affected,
even by relatively large changes of K and D. Only for very small values of K, the step response
becomes slower; and for very large values of the damping, D, some overshoot becomes visible. Changes
in the time constant, T, do, for larger values, increase overshoot and oscillations more than in the
first-order case.
In order to fully appreciate the robustness towards parameter changes of the process, one has to
compare these results against standard controllers, such as PID, as will be done in Section3.2.6.
3.2.2. Effect of Observer Pole Locations
In the previous section, we saw that changes in the process time constant, T, affected the closed loop
behavior stronger than changes inKand D. We will therefore demonstrate the influence of the observer
poles on the sensitivity by repeating the experiments with varyingT for different observer pole locations.
In the previous experiments, the observer poles were set ten times to the left of the closed loop poles
in thes-plane,i.e.,sESO =10 sCL. Here, both slower and faster observers will be examined, as well, by
settingsESO =100 sCL andsESO =5 sCL.
As visible in the simulation results in Figure12,almost ideal behavior canat least in theorybe
obtained by placing the observer poles far enough left in the s-plane, i.e., choosing large factors
k in
sESO
=k
sCL
. Of course, this comes at the price of the need for faster actuators and largercontroller outputs. Furthermoreas we will see in Section 4.2faster observers are more sensitive
to measurement noise and will be limited by sample time restrictions in discrete time implementations.
3.2.3. Effect of Actuator Saturation
Analogously to Section3.1.3,the experiments were carried out by extending the controller structure,
such that the saturated controller output, ulim(t), was fed back to the observer instead ofu(t) (compare
Figure5for the first-order case). The resulting step responses and controller outputs for varying process
parameters can be found in Figure13. As expected, lowering the DC gain,K, of the process forced the
controller into saturation, such that the desired process output could not be reached anymore. It has to
be stressed again that the controller output did not wind up, as visible in Figure 13.
8/10/2019 Active Disturbance Rejection
19/34
Electronics2013,2 264
Figure 11. Experiment3.2.1:a fixed second-order ADRC controlling second-order process
with varying parameters. Nominal process parameters: K= 1, D = 1, T = 1. ADRC
parameters: b0= KT2 =1, Tsettle= 5, sESO =10 sCL. (a) Variation ofK, closed loop stepresponse; (b) Controller outputu for (a); (c) Variation ofD, closed loop step response; (d)
Controller outputufor (c); (e) Variation ofT, closed loop step response; (f) Controller output
ufor (e).
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
(a)
0 5 10 155
0
5
10
15
t
u
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
(b)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
D = 1
D = 0.1
D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(c)
0 5 10 150
1
2
3
4
5
6
t
u
D = 1
D = 0.1
D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(d)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(e)
0 5 10 152
0
2
4
6
t
u
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(f)
8/10/2019 Active Disturbance Rejection
20/34
Electronics2013,2 265
Figure 12. Experiment3.2.2: effect of observer pole locations for a second-order ADRC
controlling second-order processes with varying parameter,T. Nominal process parameters:
K= 1,D =1, T=1. ADRC parameters: b0= KT2 =1,Tsettle= 5,sESO varying. (a) Closedloop step response, sESO =100 sCL; (b) Controller output u for (a); (c) Closed loop step
response, sESO =10 sCL; (d) Controller output u for (c); (e) Closed loop step response,
sESO =5 sCL; (f) Controller outputu for (e).
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(a)
0 5 10 155
0
5
10
15
t
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(b)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
.
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(c)
0 5 10 152
0
2
4
6
t
u
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(d)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(e)
0 5 10 151
0
1
2
3
4
t
u
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(f)
8/10/2019 Active Disturbance Rejection
21/34
Electronics2013,2 266
Figure 13. Experiment3.2.3: effect of actuator saturation, |ulim| 3, on a fixed second-order
ADRC controlling a second-order process with varying parameters. Nominal process
parameters:K= 1,D = 1,T= 1. ADRC parameters:b0= K
T2 = 1,Tsettle= 5,s
ESO = 10sCL.
The controller outputs are shown before the limitation (dashed line) takes effect. (a)
Variation ofK, closed loop step response; (b) Controller outputu for (a); (c) Variation ofD,
closed loop step response; (d) Controller outputufor (c); (e) Variation ofT, closed loop step
response; (f) Controller outputu for (e).
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
(a)
0 5 10 151
0
1
2
3
4
5
t
u
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2K = 5
(b)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
D = 1
D = 0.1
D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(c)
0 5 10 150
1
2
3
4
t
u
D = 1
D = 0.1D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(d)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(e)
0 5 10 151
0
1
2
3
4
t
u
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(f)
8/10/2019 Active Disturbance Rejection
22/34
Electronics2013,2 267
Figure 14.Experiment 3.2.4: effect of dead time,Tdead, on a second-order ADRC controlling
a process with second-order dynamics (K= 1,D = 1,T= 1) and unknown dead time. ADRC
parameters:b0= KT2
=1, Tsettle= 5,sESO =5 sCL. In (c) and (d), a fixed dead time,TESOdead,
was incorporated into the observer to improve the controller behavior. ( a) Variation ofTdead,closed loop step response; (b) Controller output u for (a); (c) Closed loop step response,
observer withTESOdead =0.1; (d) Controller outputu for (a).
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
Tdead
= 0
Tdead
= 0.1
Tdead
= 0.2
Tdead
= 0.3
(a)
0 5 10 150.4
0.6
0.8
1
1.2
1.4
1.6
t
u
Tdead
= 0
Tdead
= 0.1
Tdead
= 0.2
Tdead
= 0.3
(b)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
Tdead
= 0
Tdead
= 0.1
Tdead
= 0.2
Tdead
= 0.3
(c)
0 5 10 150.4
0.6
0.8
1
1.2
1.4
1.6
t
u
Tdead
= 0
Tdead
= 0.1
Tdead
= 0.2
Tdead
= 0.3
(d)
When decelerating the process (increased damping D), the closed loop dynamics suffered when the
controller output ran into saturation (increased settling time), but there were no additional oscillations
after recovering from saturation, as known from classical PID control without anti-windup measures.
3.2.4. Effect of Dead Time
Similar to Section3.1.4, the second-order ADRC was confronted with an unknown dead time in the
process withTdead 0.3. One can see from Figure14(a)that the controller and observer work very well
together, such that the output is hardly being affected by the dead time, which is also an improvement
compared to the first-order case in Section 3.1.4. In the controller output in Figure14(b), however,
oscillations become increasingly visible with larger values ofTdead. Again, this situation can be improvedby delaying the input of the observer, i.e., using u(t TESOdead) instead ofu(t) in Equation (12). For a
8/10/2019 Active Disturbance Rejection
23/34
Electronics2013,2 268
Figure 15. Experiment3.2.5: effect of structural uncertainties on a second-order ADRC
controlling a process with dominating second-order behavior (K=1, D= 1, T=1) and
higher-order dynamics caused by an unknown third pole at s = 1/T3. ADRC parameters:
b0=
K
T2 =1, Tsettle= 5, sESO
=5 sCL
. (a) Variation ofT3, closed loop step response; (b)Controller outputu for (a).
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T3= 0.001
T3= 0.01
T3= 0.1
T3= 1
(a)
0 5 10 150.5
1
1.5
2
t
u
T3= 0.001
T3= 0.01
T3= 0.1
T3= 1
(b)
fixed value, TESOdead =0.1, the controller behavior is shown in Figure 14(c)and(d), where the controller
oscillations are already significantly reduced, even ifTESOdead does not match the actual dead time.
3.2.5. Effect of Structural Uncertainties
Besides unknown dead times, the controller may be faced with higher-order dynamics in the process.
Therefore, the effect of an unknown third pole in the process was examined in Figure 15. The time
constant,T3, of the third pole was varied within 0.001 T3 1,i.e., the third pole was identical to the
two known poles of the plant in the extreme case. In contrast to the first-order ADRC in Section3.1.5, the
second-order ADRC proved to have very good robustness against an unknown higher-order dynamics,
even in the more challenging cases of Figure15.
3.2.6. Comparison to PI and PID Control
To view and assess the abilities of the second-order ADRC from a perspective of classical control, we
will now employ standard PI and PID controllers andafter fixing their parametersexpose them to
the same process parameter variations, as done in Section3.2.1. To ensure comparability, all controllers
are being designed for the same closed loop dynamics (settling timeTsettle= 5, no overshoot) using the
nominal process parameters,K= 1,D=1,T=1.
The PI controller is given and parameterized as follows:
CPI(s) =KP+KI
s with KI=
2.55
KTsettle=0.51 and KP= KI 1.5 D T=0.765
8/10/2019 Active Disturbance Rejection
24/34
Electronics2013,2 269
Figure 16. Experiment3.2.6: comparison of second-order ADRC, PI and PID controllers
faced with varying process parameters,K,DandT. Nominal process and ADRC parameters
are as throughout Section3.2.For each combination, the closed loop step response is shown.
(a) Variation ofK, ADRC; (b) Variation ofK, PI; (c) Variation ofK, PID; (d) Variation ofD, ADRC; (e) Variation ofD, PI; (f) Variation ofD, PID; (g) Variation ofT, ADRC; (h)
Variation ofT, PI; (i) Variation ofT, PID.
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
(a)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
(b)
0 5 10 15
0
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
K = 1
K = 0.1
K = 0.2
K = 0.5
K = 2
K = 5
(c)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
D = 1
D = 0.1
D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(d)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
D = 1
D = 0.1
D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(e)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
D = 1
D = 0.1
D = 0.2
D = 0.5
D = 2
D = 5
D = 10
(f)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(g)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(h)
0 5 10 150
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
T = 1
T = 0.5
T = 2
T = 3
T = 3.5
(i)
For the PID controller, we will employ a PIDT1-type controller in two-pole-two-zero form, designed
such that the zeros of the controller cancel the process poles. The controller gain is chosen to match the
closed loop dynamics to the PI and ADRC case:
CPID(s) =KI (1 + TZ1 s)(1 + TZ2 s)
s (1 + T1 s) with KI=
3
KTsettle=0.6, TZ1/2= T=1 and T1=0.2
The simulation results are compiled in Figure 16, where each column represents one of the three
controller types and each row, a different process parameter being varied. To summarize, it has to
be stated that in each case, the ADRC approach surpasses the results of PI and PID control by a large
margin with respect to sensitivity towards parameter variations, with a slight advantage of PID compared
to PI control.
8/10/2019 Active Disturbance Rejection
25/34
Electronics2013,2 270
Figure 17. Experiment3.2.7: comparison of disturbance rejection behavior (second-order
ADRC vs. PI vs. PID controller). Process and ADRC parameters are as throughout
Section3.2. Input disturbance,d=0.5, effective fromt= 15 untilt= 25. (a) Step response
and reaction on disturbance; (b) Controller outputu for (a).
0 5 10 15 20 25 30 350
0.2
0.4
0.6
0.8
1
1.2
1.4
t
y
ADRC
PI
PID
(a)
0 5 10 15 20 25 30 350
0.5
1
1.5
2
2.5
3
t
u
ADRC
PI
PID
(b)
3.2.7. Disturbance Rejection of ADRC, PI and PID
As our final experiment for the second-order case, we will evaluate the disturbance rejection
capabilities of ADRC, PI and PID control using the controller settings from the previous section. All of
them are tuned for the same closed loop response.
For each control loop, an input disturbance, d=0.5, is applied during a ten-second interval afterreaching steady state; compare Figure 17. One can easily recognize that ADRC compensates the
disturbance much faster, such that its effect on the control variable remains very low. While both PI and
PID controllers could also be tuned more aggressively for a similar disturbance rejection behavior, one
would have to employ additional measures, such as setpoint filters, to retain a non-oscillating reference
tracking behavior.
4. Discrete Time ADRC
Practical implementations of a controller with a state observer, such as the ADRC approach, will mostlikely be done in discrete time form, e.g. employing a microcontroller. Since the actual control law for
linear ADRC is based on proportional state feedback, a discrete time version can already be obtained by
only discretizing the extended state observer, which will be done in Section4.1. The quasi-continuous
approach will be valid only for sufficiently fast sampling, of course. Otherwise, the state feedback should
be designed explicitly for a discretized process model incorporating sampling delays.
In Section4.2,simulative experiments will be carried out in order to visually assess the influence of
the discretisation process and measurement noise on the control loop performance.
8/10/2019 Active Disturbance Rejection
26/34
Electronics2013,2 271
4.1. Discretisation of the State Observer
For a system without a feed-through term, the standard approach for a discrete-time observer is:
x(k+ 1) =Ad x(k) +Bd u(k) +Lp (y(k)Cd x(k)) (22)
If we look at the equation for the estimation error of Equation ( 22), we can see thatjust as in the
continuous casethe dynamics of the error decay are determined by the matrixAdLp Cd
:
e(k+ 1) =x(k+ 1) x(k+ 1) =Ad Lp Cd
(x(k) x(k))
Since the observer gains in Lpinfluence the pole placement for the matrixAdLp Cd
, they can be
chosen such that the estimation settles within a desired time.
Here,Ad,Bdand Cdrefer to time-discrete versions of the respective matrices in the state space process
models Equations (3) and (11) obtained by a discretisation method. Since there is no matrixDd in the
observer equations, the discretisation of the model must deliver Dd=0, for example, via zero order hold
(ZOH) sampling. This observer approach is also being called prediction observer, since the current
measurement, y(k), will be used as a correction of the estimate only in the subsequent time step, x(k+ 1).
In order to reduce unnecessary time delays (which may even destabilize the control loop), it
is advisable [16] to employ a different observer approach called filtered observer or current
observer [17]. The underlying idea issimilar to Kalman filteringto split the update equation in
two steps, namely a prediction step to predict x(k|k 1) based on measurements of the previous time
step, k 1, and a correction step to obtain the final estimate, x(k|k), incorporating the most recentmeasurement, y(k):
x(k|k1) =Ad x(k1|k1) +Bd u(k1) (prediction)
x(k|k) = x(k|k1) +Lc (y(k)Cd x(k|k1)) (correction)
If we put the prediction into the correction equation and abbreviate x(k|k) = x(k), we obtain one
update equation for the observer:
x(k) = (AdL
cC
dA
d) x(k1) + (B
dL
cC
dB
d) u(k1) +L
cy(k) (23)
From the estimation error, we can see that, in contrast to the prediction observer, the error dynamics
are determined by the matrix(AdLc Cd Ad):
e(k+ 1) =x(k+ 1) x(k+ 1) = (AdLc Cd Ad) (x(k) x(k))
When computing the observer gains inLc, this has to be taken into account, i.e., one must chooseLc,
such that the eigenvalues of(AdLc Cd Ad)match the desired observer pole locations.
The discrete time versions of the matricesA,B andCfrom the the state space process models, which
are necessary for the observer equations, can be obtained by ZOH discretisation [17]:
Ad=I+
i=1
Ai Tisamplei!
, Bd=
i=1
Ai1 Tisamplei!
B, Cd= C, Dd= D (24)
8/10/2019 Active Disturbance Rejection
27/34
Electronics2013,2 272
For the first-order process in Equation (3),A and B are being discretized as follows, whileCd= C=1 0
andDd=D=0 remain unchanged:
A= 0 10 0 , B= b00 gives Ad= 1 Tsample0 1 , Bd= b0 Tsample0 This can be computed via Equation (24) easily, sinceAi =0 fori 2. Following the same procedure
for the second-order case in Equation (11),Cd= C=
1 0 0
andDd= D = 0 remain unchanged,
and one obtains forAdand Bd(sinceAi =0 fori 3):
A=
0 1 00 0 10 0 0
, B= 0b0
0
gives Ad=1 Tsample T
2sample/2
0 1 Tsample
0 0 1
, Bd=b0 T
2sample/2
b0 Tsample
0
Now, one can compute the observer gain, Lc = l1 l2T (first-order case) or Lc = l1 l2 l3T
(for the second-order ADRC) to obtain the desired observer dynamics. The desired pole locations can,
in a first step, be formulated in the s-plane, as in Sections 2.1 and 2.2, and then be mapped to the
z-plane: zESO =esESOTsample . The computation ofLc may either be done numerically or analytically. To
demonstrate this, we will derive the equations for the first-order case with one common pole location,
zESO, for both poles:
det(zI (Ad Lc Cd Ad)) !=zzESO
2detz + l11 l1 TsampleTsamplel2 z + l2 Tsample1 !=z22 zESO zzESO2z2 +
l1+ l2 Tsample2
z + (1 l1)
!=z22 zESO z
zESO
2By comparing the coefficients, one obtains forl1 and l2 (solutions for higher-order observers can be
found in [16]):
l1=1zESO
2, l2=
1
Tsample
1zESO
2 (25)
As in the continuous time case in Section2,the implementation and design of a discrete time linear
ADRC can be summarized in four steps, where the first-order and second-order case are distinguished
by (a) and (b):
1. Modeling:
(a) For a process with dominating first-order behavior, P(s) = K
T s + 1, one should provide an
estimateb0 KT
.
(b) For a second-order process, P(s) = K
T2s2 + 2DT s + 1, an approximate value b0
KT2
is sufficient.
2. Control structure:
Implement a discrete-time observer with two state variables, x(k) = x1(k) x2(k)T (for thefirst-order case) or three state variables x(k) =
x1(k) x2(k) x3(k)
T(for the second-order case),
as follows:
8/10/2019 Active Disturbance Rejection
28/34
Electronics2013,2 273
x(k) = (AdLc Cd Ad) x(k1) + (Bd Lc Cd Bd) u(k1) +Lc y(k)
Using the estimated state variables, implement a proportional state feedback controller:
(a) u(k) =KP (r(k) y(k)) f(k)
b0=
KP (r(k) x1(k)) x2(k)
b0
(b) u(k) =
KP (r(k) y(k))KD y(k)
f(k)
b0=
(KP (r(k) x1(k))KD x2(k)) x3(k)
b0
3. Closed loop dynamics:
Choose the controller parameters, e.g. via pole placement according to a desired settling time:
(a) KP= sCL with sCL
4
Tsettle
(b) KP=
sCL2
, KD= 2 sCL with sCL
6
Tsettle
4. Observer dynamics:
Place the desired observer poles far enough left of the closed loop poles in the s-plane, e.g. by a
common location, sESO =kESO sCL (3 . . . 10) sCL. Map to thez-plane viazESO =es
ESOTsample
and compute the necessary observer gains:
(a) l1=1zESO
2, l2=
1Tsample
1zESO2
(b) l1=1zESO
3, l2=
32Tsample
1zESO2
1 +zESO
, l3= 1
T2sample
1zESO3
4.2. Simulative Experiments
As in the continuous-time experiments in Section 3.1, a first-order process will be examined in
this section:
P(s) =y(s)
u(s)=
K
T s + 1 with K=1 and T=1
Unless otherwise noted in individual experiments, the ADRC will be designed assuming perfect
knowledge, b0=K/T=1, withkESO= 5, and a desired 2% settling time, Tsettle= 1. The discretisation
will be based on a sampling time Tsample= 0.01. Gaussian measurement noise will be added with a
variance 2noise= 0.0001.
4.2.1. Effect of Sample Time
When choosing the sampling time for a discrete-time implementation of a controller with an observer,
one has to consider not only the process dynamics, but also the dynamics of the observer. If, on the other
hand, restrictions to sample times are present, the dynamics of the observer will be limited. In the
case of ADRC, this would mean that the desired behavior of the process may not be achieved under
all circumstances.
In Figure18, simulations were performed using sample times for ADRC ranging from Tsample=0.01
to Tsample=0.20. As expected, oscillations in the controller output are increasingly visible for large
sample times. Consequently, the closed loop dynamics differ from the desired first-order behavior as thesampling interval becomes too coarse.
8/10/2019 Active Disturbance Rejection
29/34
Electronics2013,2 274
Figure 18. Experiment4.2.1: influence of different sample time settings on discrete-time
ADRC. Measurement noise variance: 2noise= 0.0001. Observer pole placement: kESO= 5.
(a) Variation ofTsample, closed loop step response; (b) Controller outputu for (a).
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
t
y
Ts = 0.01
Ts = 0.02
Ts = 0.05
Ts = 0.1
Ts = 0.2
(a)
0 0.5 1 1.5 20
1
2
3
4
t
u
Ts = 0.01
Ts = 0.02
Ts = 0.05
Ts = 0.1
Ts = 0.2
(b)
Figure 19. Experiment 4.2.2: influence of different levels of measurement noise on
discrete-time ADRC. Sample time: Tsample=0.01. Observer pole placement: kESO= 5.
(a) Variation of2noise, closed loop step response; (b) Controller outputu for (a).
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
t
y
noise = 0
noise = 0.001
noise = 0.0001
noise = 1e05
(a)
0 0.5 1 1.5 20
1
2
3
4
t
u
noise = 0
noise = 0.001
noise = 0.0001
noise = 1e05
(b)
4.2.2. Effect of Measurement Noise
While state feedback controllers based on observers rather than direct measurements are less
susceptible to measurement noise, oscillations in the controller output will still occur with higher noise
levels. In the simulations presented in Figure19, normally distributed noise with increasing variance
ranging from 2noise= 0 to 2noise= 0.001 was added to the process output. The results correspond to
these expectations. The effect of measurement noise on oscillations in the controller output, however,
may be mitigated by designing an observer with slower dynamics, which will be demonstrated in the
following experiment.
8/10/2019 Active Disturbance Rejection
30/34
Electronics2013,2 275
Figure 20. Experiment4.2.3: influence of observer pole placement viakESOon discrete-time
ADRC. Sample time: Tsample=0.01. Measurement noise variance: 2noise=0.0001. (a)
Variation ofkESO, closed loop step response; (b) Controller outputu for (a).
0 0.5 1 1.5 20
0.2
0.4
0.6
0.8
1
1.2
t
y
kESO = 5
kESO = 1
kESO = 2
kESO = 10
(a)
0 0.5 1 1.5 20
1
2
3
4
t
u
kESO = 5
kESO = 1
kESO = 2
kESO = 10
(b)
4.2.3. Effect of Observer Pole Locations
In the simulations with varying observer dynamics presented in Figure 20, the typical trade-off
between fast setpoint tracking and noise rejection becomes visible. If the observer poles are placed
far enough left of the closed loop poles in the s-plane viakESO, the closed loop dynamics can adopt the
desired first-order behavior, but the control variable becomes more sensitive to measurement noise and
increasingly exhibits unwanted oscillations. On the other hand, placing observer poles near the closed
loop poles provides good measures to suppress the effect of measurement noise on the control action,
but the closed loop dynamics will suffer, especially under process parameter changes, cf. Sections3.1.2
and3.2.2.
5. Optimized Discrete-Time Implementation
In a practical discrete-time implementation with tight timing constraints, the lag between sensor
input and controller output should be as small as possible, which means that one should try to reduce
the computational effort for a controller. Due to the observer-based approach, ADRC has a bigger
computational footprint than a classical PID-type controller. In this section, we will try to reduce the
number of computations, on the one hand, and present an implementation focused on low input-output
delay, on the other hand.
5.1. State Variable Transformation
We start with the discrete-time observer from Equation (23) in the following abbreviated form:
x
(k
) =A
ESO x
(k1) +
BESO
u(
k1) +
LESO
y(
k)
and with a control law for the first-order or second-order case:
u(k) =KP (r(k) x1(k)) x2(k)
b0or u(k) =
(KP (r(k) x1(k))KD x2(k)) x3(k)
b0
8/10/2019 Active Disturbance Rejection
31/34
Electronics2013,2 276
Figure 21. Control loop with modified ADRC structure and transformed state variables, x.
(a) Modified first-order structure; (b) Modified second-order structure.
Process
KP
b0
Observer
u yr
x1
x2
(a)
Process
KP
b0
Observer
u yr
x1
x3
x2
(b)
One can simplify the controller structure by scaling the outputs of the observer, such that the
multiplications byb0,KP and KD(the latter only for the second-order case) can be omitted. The desired
scaling of the new state variables, xi, is achieved via:(a) x1=
KP
b0 x1, x2=
1
b0 x2 (for the first-order case)
(b) x1=KP
b0 x1, x2=
KD
b0 x2, x3=
1
b0 x3 (for the second-order case)
The ADRC structure can then be modified as given in Figure 21. Generally speaking, we perform a
coordinate transformation from the old estimated variables xto xby means of a transformation matrix:
T1
=
1
b0 KP 00 1 (1st order ADRC) or T1 = 1b0 KP 0 0
0 KD 00 0 1
(2nd order) (26)Using this matrixT, the state space equations for the extended state observer must be transformed in
order to obtain an ESO working with our new state variables, x=T1 x:
AESO= T1 AESO T, BESO=T1 BESO,LESO=T1 LESO (27)In this manner, multiplications of the state variables by b0, KP andKD can be avoided. Provided the
reference,r(k), does not change at each point in time, one can precompute KPb0 r, as well. The control
laws are being simplified to the following form:
u(k) =KP
b0 r(k) x1(k) x2(k) or u(k) =
KP
b0 r(k) x1(k) x2(k) x3(k)
5.2. Minimizing Latency by Precomputation
In an application with fixed sampling frequency, the controller performance can be improved by
minimizing the latency between acquisition of input signals and output of the updated controller action
within a sampling period. This input-output lag is not necessarily dependent on the overall number of
computations of a control law, but rather on the computations necessary to deliver the controller output,with the computations left being performed after that during the remaining time of the sampling period.
We will optimize the discrete-time implementation of ADRC in this regard and, subsequently, derive
further equations in detail for the second-order case. Following the ideas of the previous section, the
8/10/2019 Active Disturbance Rejection
32/34
Electronics2013,2 277
estimated state variables must be updated according to Equation (28) and used to compute the controller
output in Equation (29), at each point in timek:
x(k) =AESO x(k1) + BESO u(k1) +LESO y(k) (28)with x=
x1x2x3
, AESO=a11a12a13a21a22a33a31a32a33
, BESO=b1b2b3
,LESO=l1l2
l3
u(k) =
KP
b0 r(k) x1(k) x2(k) x3(k) =
KP
b0 r(k)
1 1 1
x(k) (29)
When inserting Equation (28) into Equation (29), one can see that u(k) depends both on variables
from timek,y(k)and r(k), and from time k1,u(k1)and x(k1). An idea for providing u(k)with
lower latency would therefore be to precompute all terms stemming from timek1 already atk1 andonly update this precomputed value, u(k|k1), at timekto obtain and outputu(k) = u(k|k), as soon as
the necessary measurements become available. Further optimization is possible if the reference value, r,
does not change rapidly, remains constant or is known in advance. We will denote this byr(k+ 1|k),i.e.,
r(k+ 1)is already known at time k, for any of the reasons mentioned. Then, only the measured process
output,y(k), has to be included in the update step to obtain u(k) =u(k|k):
u(k) =u(k|k1)
1 1 1
LESO y(k) =u(k|k1)l1+l2+l3 y(k) (30)
In Equation (30), the sum(l1+l2+l3)can be precomputed as well, such that only one multiplication
and one addition is necessary to calculate the controller output, u(k). After that, the remaining time
of the sampling period can be used to update the observer states via Equation (31) and precompute the
output via Equation (32) for the next point in time, k+ 1:
x(k+ 1|k) =AESO x(k|k1) +LESO y(k) x(k)
+BESO u(k) (31)
u(k+ 1|k) =KP
b0 r(k+ 1|k)
1 1 1
x(k+ 1|k) (32)
Note that the actual observer states, x(k), are not explicitly present and updated in the equations
anymore, since only the precomputed values, x(k+ 1|k), are needed. To summarize, a latency-optimized
discrete-time implementation has to perform the following four steps at each point in time k, with the
new controller output,u(k), being available already after the second step:
1. Acquire the current measurement of the process output,y(k).
2. Calculate and outputu(k)by Equation (30).
3. Update the internal observer states by Equation (31).
4. Precompute the controller output fork+ 1 using Equation (32).
8/10/2019 Active Disturbance Rejection
33/34
Electronics2013,2 278
6. Conclusions
By means of simulative experiments using generic first-order and second-order plants, it could
be demonstrated that ADRC can be a powerful control tool. In this article, the linear case was
examined. It can adapt even to heavily varying process parameters, andin contrast to classical
adaptive controllersdo so without having to maintain an explicit model of the process. Since only
little knowledge about a process has to be provided along with the desired closed loop dynamics, the
parameterization is easy for both continuous time and discrete time cases and, therefore, appealing
to practitioners.
For control problems with high dynamic requirements, an optimized formulation of the discrete time
linear ADRC equations can be found, which enables the controller output to be computed with only one
addition and one multiplication after the sensor input becomes available.
If ADRC can show its full potential in a specific application does, however, depend on the relationof process dynamics, observer dynamics, sampling time and measurement noise. In order to provide
the adaptability, the observer has to be fast enough compared to the process and closed loop dynamics,
on the one hand. On the other hand, the placement of the observer poles will be limited by sampling
frequency and the increasing effects of noise on the control action. As long as a good compromise can be
found in this regard, ADRC has to be considered as a strong and welcome alternative to solving practical
control problems.
Acknowledgments
The author would like to thank the reviewers for their helpful suggestions and comments.
Conflicts of Interest
The author declares no conflicts of interest.
References
1. Han, J. From PID to active disturbance rejection control. IEEE Trans. Ind. Electron. 2009,
56, 900906.
2. Gao, Z.; Huang, Y.; Han, J. An Alternative Paradigm for Control System Design. In Proceedings of
the 40th IEEE Conference on Decision and Control, Orlando, Florida, USA, 47 December 2001.
3. Gao, Z. Scaling and Bandwidth-Parameterization Based Controller Tuning. In Proceedings of the
2003 American Control Conference, Denver, Colorado, USA, 46 June 2003; pp. 49894996.
4. Gao, Z. Active Disturbance Rejection Control: A Paradigm Shift in Feedback Control System
Design. In Proceedings of the 2006 American Control Conference, Minneapolis, Minnesota, USA,
1416 June 2006; pp. 23992405.
5. Sun, B.; Gao, Z. A DSP-based active disturbance rejection control design for a 1-kW H-bridge
DC-DC power converter. IEEE Trans. Ind. Electron. 2005, 52, 12711277.6. Su, Y.X.; Zheng, C.H.; Duan, B.Y. Automatic disturbances rejection controller for precise motion
control of permanent-magnet synchronous motors. IEEE Trans. Ind. Electron. 2005, 52, 814823.
8/10/2019 Active Disturbance Rejection
34/34
Electronics2013,2 279
7. Vincent, J.; Morris, D.; Usher, N.; Gao, Z.; Zhao, S.; Nicoletti, A.; Zheng, Q. On active disturbance
rejection based control design for superconducting RF cavities. Nuclear Instrum. Methods Phys.
Res. A2011, 643, 1116.
8. Zheng, Q.; Gao, Z. On Practical Applications of Active Disturbance Rejection Control. InProceedings of the 29th Chinese Control Conference, Beijing, China, 2931 July 2010; pp.
60956100.
9. Francis, B.A.; Wonham, W.M. The internal model principle of control theory. Automatica 1976,
12, 457465.
10. Qin, S.J.; Badgwell, T.A. A survey of industrial model predictive control technology. Control Eng.
Pract. 2003, 11, 733764.
11. Canuto, E. Embedded model control: Outline of the theory. ISA Trans. 2007, 46, 363377.
12. Radke, A.; Gao, Z. A Survey of State and Disturbance Observers for Practitioners. In Proceedings
of the 2006 American Control Conference, Minneapolis, Minnesota, USA, 1416 June 2006; pp.51835188.
13. Chen, X.; Li, D.; Gao, Z.; Wang, C. Tuning Method for Second-order Active Disturbance Rejection
Control. In Proceedings of the 30th Chinese Control Conference, Yantai, China, 2224 July 2011;
pp. 63226327.
14. Ostertag, E. Mono- and Multivariable Control and Estimation; Springer: Berlin, Heidelberg,
Germany, 2011.
15. Araki, M.; Taguchi, H. Two-degree-of-freedom PID controllers. Int. J. Control, Autom. Syst.
2003, 1, 401411.
16. Miklosovic, R.; Radke, A.; Gao, Z. Discrete Implementation and Generalization of the Extended
State Observer. In Proceedings of the 2006 American Control Conference, Minneapolis,
Minnesota, USA, 1416 June 2006; pp. 22092214.
17. Franklin, G.F.; Workman, M.L.; Powell, D. Digital Control of Dynamic Systems, 3rd ed.;
Addison-Wesley Longman Publishing: Boston, MA, USA, 1997.
c 2013 by the author; licensee MDPI, Basel, Switzerland. This article is an open access article
distributed under the terms and conditions of the Creative Commons Attribution license
(http://creativecommons.org/licenses/by/3.0/).