Post on 11-Aug-2020
transcript
Page 1 of 8
1A Parts in this box.
1B Hardware in this box.
Queen size only:Extra parts.
1C
BIFOLD FUTON FRAME Assembly Instructions Full Size • Queen Size
*Note: Use 4pc of 100mm Bolts and 4pc of 60mm Boltsto attach the arms to the Stretchers.
Clevis Pinsx 2
Long Allen Keyx 1
Metal Bracketx 4
16mmBolts x 16
WoodenDowels x 18
30mmBolts x 12
60mmBolts x 10
80mmBolts x 4
WoodButtons x 4
BarrelNuts x 18
100mmBolts x 4
B3 Roller completewith Clevis pin, Washer and
Locking pin x 4
Back Side Rails x 2
Arms x 2
Stretchers x 2
Back Rails and Slats x 1
Seat Rails and Slats x 1
Seat Side Rails x 2
Full Size: Slat Supports x 6
2pc with extra holes& plastic stoppers
2pc with extra holes
Queen Size: Slat Supports x 6
2pc with extra holes& plastic stoppers
2pc with extra holes
3pc are longer forthe Back deck
50mm Bolts x 2
Short Legs x 2
WINSTON TRAY ARM0309
30mm Bolts
30mm Bolts
16mm Bolt
16mm Bolt
16mm Bolts
16mm Bolts
Page 2 of 8
2A
The Back Deck slat bundle is longer than the seat. Identify the correct slat supports as shown below,and fit under the slats. *Queen size pleasenote: The Slat supports for the BackDeck are longer than on the Seat.
Fit the Slat Supports to the Back Deck.
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
Slat support*without Holes.
Slat support*with Holes.
Back Deck Railsand Slats (longer)
Slat support*with Holes.
Holes.
Holes.
Important! Leave the bolts a bit loose.
16mm Bolt 30mm Bolt
BIFOLD FUTON FRAME
WINSTON TRAY ARM2B
Use the 16mm Bolts and the30mm Bolts to attach theSlat supports, butdo not fully tighten them yet!
Fit the B3 Rollers to theBack Side Rails
Clevis pins
Washers
Locking pins
Back Side Rail
B3 Rollers
0309
60mm Bolt
60mm Bolt
Wooden Dowels
Barrel Nut
Barrel Nut
Wooden Dowels
Barrel Nut
Wooden Dowels
60mm Bolt
60mm Bolt
Barrel Nut
Barrel Nut
Wooden Dowels
Back Side Rail(Right Hand)
Back Side Rail(Left Hand)
The Bolts should be leftloose to make aligningthe parts easier.
Push fit or lightly tap the Wooden dowels into the ends of theSeat deck. Use 60mm bolts and Barrel nuts to fix theBack Side Rails to the Back deck.
Do not fully tighten any of the bolts yet!
Page 3 of 8
3A Assemble the Side Rails to the Back Deck.
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
WoodButton
WoodButton
Only when all the parts are correctlyin place, should you tighten all the Bolts.
Finally, fit the two wood buttons.
BIFOLD FUTON FRAME
WINSTON TRAY ARM0309
Use the 16mm Bolts and the 30mmBolts to attach the Slat supports, butdo not fully tighten them yet!
Page 4 of 8
4A
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
Slat support*with Holes andPlastic stoppers.
Seat Deck Railsand Slats (shorter)
WoodBlock
WoodBlock
Slat supportwithout Holes.
Slat support*with Holes andPlastic stoppers.
Plasticstoppers.
Holes
30mm Bolts
30mm Bolts
16mm Bolts
16mm Bolt
16mm Bolt
16mm Bolts
Important! Leave the bolts a bit loose.
16mm Bolt 30mm BoltThe Seat Deck slat bundle is shorter than the seat. Identify the correct slat supports as shown below,and fit under the slats.
Fit the Slat Supports to the Seat Deck.
BIFOLD FUTON FRAME
WINSTON TRAY ARM0309
Push fit or lightly tap the Wooden dowels into the ends of theSeat deck. Use bolts and Barrel nuts to fix the Back Side Railsto the Seat deck.
Do not fully tighten any of the bolts yet!
Page 5 of 8
60mm Bolt
Wooden Dowel
Barrel Nut
Seat Side Rail(Right Hand)
Wooden Dowels
Barrel Nuts80mmBolts
WoodenDowel
Barrel Nuts
60mm Bolt atthe front
Barrel Nut
Wooden Dowels
Seat Side Rail (Left Hand)
Underneath, the Plastic stoppersshould be towards the front.
80mm Boltsat the back
80mmBolts
60mmBolt
5A Assemble the Side Rails to the Seat Deck.
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
Wood Button
WoodButton
With the Side Rails loosely bolted in place,ease the ends of the slats into the grooves onthe side rails. Only when all the parts are correctlyin place, should you tighten all the Bolts.
Finally, fit the two wood buttons.
BIFOLD FUTON FRAME
WINSTON TRAY ARM0309
Page 6 of 8
Attach Arms to Stretchers.6C
Using Bolts and Barrel Nuts attach theArms loosely to the Stretchers as shown.
It is important that these Boltsare left LOOSE!
Be sure the holes arefree of wood chipsand saw dust.
Do not force the Boltas you may strip thethread. Be sure thethread is properly started.
Barrel NutBolt
Allen Key Screwdriver
BOLT AND BARREL NUTASSEMBLY SYSTEMInsert Barrel Nuts as shown using a screwdriver. This will help you position the Nut inline with the Bolt.
Bolt
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
Rear stretcher ( no plates )
The Front Stretcher has metal plates which should face upwards.
THIS ENDFRONT
Do not tightenthe Bolts atthis stage!
WoodenDowel
BarrelNuts
BarrelNuts
60mmBolts
100mm Bolts
100mm Bolts
Fit Wooden Dowels to the Stretchers.
6A Fasten Stretcher Brackets to the Arms:
A. Insert the Stretcher Bracket Cleat into the hole provided.
B. IMPORTANT: Don't fully tighten Bracket until Stretchers are all in place for easy alignment.
Cleat
Stretcher Bracket
Hole for Cleat
Leg
Dowel Hole
16mm Bolt
Allen Key
Hole for Bolt
C. Each arm requires two brackets, front and back.
Tap dowels all the way into the middle hole at each end of the Stretchers.
Wooden Dowel
Stretcher
Middle hole
6B
BIFOLD FUTON FRAME
WINSTON TRAY ARM0309
Page 7 of 8
Fit the Back Deck into Position.
Use 2 People!
Please Note:
Tighten all the Bolts.7B
7A
When you have the Back Deckfitted lying flat, tightenall the Bolts.
Insert the Back Deck lying flat. Insert oneend first, then gently lower the other endinto position.
Remember that the Bolts on the Arm should be LOOSE.
Be careful not to scratch the Arms with the Plastic Runners when you lower the ends of the Back Deck.
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
CAREFUL!These can scratch the Arms.
All four joints mustbe left LOOSE.
Tighten all the Bolts.
BIFOLD FUTON FRAME
WINSTON TRAY ARM0309
Back Deck
Seat Deck
Page 8 of 8
Fit the Seat Deck inside of the Back Deck asshown. The Seat Deck is held to theBack Deck with the two ClevisPins as shown below.
Lock the Clevis Pin in place.Rotate the Clevis Pin down so it isretained by the Plastic Stopper.
Plastic Stopper
Seat Deck
Back Deck
Queen size only: Attach short legs.
Exposed part ofthe metal nut
50mm Bolt
Short Leg
Back Deck
TMCONTINENTALFRAME
Assembly Instructions Full Size • Queen Size
Attach the Seat Deck to the Back Deck.8A 8B
Clevis Pin
Wood Block
Back Deck
Seat Deck
Use the Clevis Pins to join the Seat and Back Deck.Carefully align the hole in the Wood Block on theSeat Deck with the hole in the Back Deck.
Short Leg
50mm Bolt
BIFOLD FUTON FRAME
WINSTON TRAY ARM0309