CNC- Machining Centers Optional Aggregates. Aggregates nHigh torque through optimized gears nLittle...

transcript

CNC- Machining CentersOptional Aggregates

Aggregates

High torque through optimized gears

Little wear due to precise high quality bearings and special hardened surfaces of the gears

Modular design for best flexibility

Optional Aggregates Available

78533+1 Spindles

Drilling

78542-Spindles

Drilling, SawShaping

7950Floating head

79531-Spindle

Drilling, Saw,Shaping

79542-Spindles

Drilling, Shaping

7855 / 7856 / 7857VarioNC (4½ Axes)

79551-Spindle

Saw unit (heavy duty)

79562-Spindles

79582-Spindles

Lock case

Moulding (Omega)

79592-Spindles

Lock case, Shaping

79831-Spindle

Saw, Shapeing

79574-Spindles

Drilling, Shapeing

79841-Spindle

Drilling, SawShapeing

79863-Spindles

Drilling (Horizontal)

79871-Spindle

Drilling, SawShaeping (45° fixed)

79881-Spindle

NCcollet chuck

drilling

Saw with scoring unit

Optional Aggregate# 7853

Data sheet

Optional Aggregates# 7853

HSK-F 63 collet chuck Drilling Transmission ratio: 1:1,48 9,000 rpm 3+1 spindles for collet chuck

- 0,5 – 10 mm, ER16 Drill bits with effective length up to 130 mm Drill centers in 32 mm grid 3x clockwise and 1x counterclockwise Rotatable from 0° - 360°

Datenblatt

Optional Aggregaqtes# 7854

HSK-F 63 collet chuck Transmission ratio: 1:1,48 9,000 rpm 2 spindles with collet chucks

1–16 mm, ER25 / 3–20 mm, ER32 With saw blade mount

– D = max. 220 mm, d=30 mm– 2 x driving pins, d=6 mm

Rotatable 0° - 360°

Optional AggregatesVarioNC

VarioNC 7855 (collet chuck/ saw blade mount)

VarioNC 7856(Saw blade mount)

VarioNC 7857 (ET Clamping system)

Optional AggregatesVarioNC

For machining workpiece in free plane Workpiece positioning by

– Turning (C-axis 0° - 360°) – Inclining (A-axis 0° - 100°)

Positioning of axis results from one after another (A- and C-axis)

All positioning operations are always performed outside the machining operation.Interpolation during machining is not possible.

Changing Units (Option)Turning mitre gear drive 7855

Datenblatt

with HSK-F 63 collet chuck Transmission ratio: 1:1,09 Nout (max.) 15.000 rpm

1 spindles with collet chuck

- 1-16 mm, ER25 mini With saw blade mount

d = 30 mm, max. Ø 200 mm Pivot range 0° - 100° Rotable from 0° - 360° Oil bath lubrication Variant-Packages

Datenblatt

with HSK-F 63 collet chuck Transmission ratio: 1:1,09 nout (max.) 15.000 min-1

1 spindles with saw blade mountd = 30 mm, max. Ø 200 mm

Pivot range 0° - 100° Rotable from 0° - 360° Oil bath lubrication

Variant-Packages

Datenblatt

with HSK-F 63 collet chuck Transmission ratio: 1:1,09 nout (max.) 15.000 rpm

1 spindles with collet chuck

= 30 mm, max. Ø 200 mm Pivot range 0° - 90° Rotable from 0° - 360° Oil bath lubrication

Variant-Packages

Changing Units (Option)VarioNC Variant-Packages

Vector axis (C-axis) 0°-360° can be turned infinitely

Tool changer 789212 /14 /16-fold-Magazin Pick-up

Max. Ø tool: > Space 1- 7: Ø 100 mm > Space 8-14: Ø 110 mm Maximum tool weight: > 5 kg per tool > 60 kg when full

For collect chuck with HSK shank

1x VarioNC angle pivoting gear

selectable from: 7855 / 7856 / 7857

Variant 1

Vector axis (C-axis) 0°-360° can be turnedinfinitely

Tool changer 78902-fach-Magazin - Pick-up

Max. Ø tool: > Ø 200 mm Maximum tool weight: > 6 kg per tool

For collect chuck with HSK shank

1x VarioNC angle pivoting gearchoosable from: 7855 / 7856 / 7857

Variant 2

Changing Units (Option)Floating head with head cone 7950

Changing Units (Option)Floating head with head cone

Floating head 7950,with HSK 63 F shaft – nout (max.) 10,000 rpm – with collet chuck

of 2 - 16 mm, ER25 – tracer machining

Floating head cone – with inside diameter 110 mm – with inside diameter 65.5 mm

(for floating head 7950)

Datenblatt

With HSK 63 F collet chuck Transmission ratio: 1:1 15,000 rpm Pivot range 0° - 100° With adjusting bolts with

marked angle positions Rotateable from 0° - 360°

(manual adjustment)

With collet chuck – 1–16mm, ER25

With saw chuck – D = max. 180 mm, d = 30 mm

Maintenance-free

Datenblatt

With HSK 63 F collet chuck Transmission ratio: 1:1.48 15,000 rpm Rotateable from 0° - 360°

(manual adjustment) 2 spindles with collet chucks

1–16mm, ER25 Drill bits effective length up to 130 mm 1x clockwise and 1x anticlockwise Maintenance-free

Datenblatt

With HSK 63 F collet chuck Transmission ratio: 1:0.676 10,000 rpm Rotateable from 0° - 360°

(manual adjustment) With saw blade mount

– D = max. 220 mm, d=30 mm – 2 x driving pins, d=6 mm

With self-securing clamping coverd = 56mm

Oil bath lubrication

Datenblatt

With HSK 63 F Transmission ratio: 1:1.48

15,000 rpm Rotateable from 0° - 360°

(manual adjustment) with collet chucks

1–16mm, ER25 With saw blade mount

– D = max. 160 mm, d=30 mm

– 4 x fixing screws Maintenance-free

Datenblatt

With HSK 63 F Transmission ratio: 1:1.48 15,000 rpm

Rotateable 0° - 360° (manual adjustment)

Maintenance-free 4 spindles unit with collet chucks

– 2 x 1–16mm, ER25 / 2 x 3 – 20 mm, ER 32 2 x clockwise and 2 x counterclockwise Saves valuable change-over time

Datenblatt

With HSK 63 F Lock case / cutting Transmission ratio: 1:1 12,000 rpm 1 spindle unit for tool shaft

d = 16mm Counterclockwise rotation Max. workpiece thickness 60 mm Maintenance-free

Datenblatt

With HSK 63 F Transmission ratio: 1:1.48 15,000 rpm 2 spindles unit with

– collet mount 2–20 mm, ER32 – collet mount 1–10 mm, ER16

1 x clockwise and 1 x counterclockwise Maintenance-free

Datenblatt

With HSK 63 F Transmission ratio: 1:1.48 12,000 rpm Tool fixing using

- 4 x countersunk bolts Tool diameter

- D = approx. 70 mm Ideal for sharp-edged coping

of corner cutouts (90°)

Compact (short-length) design With HSK 63 F Drilling / cutting / sawing Transmission ratio: 1:1 12,000 rpm Pivot range 0° - 100° Rotateable from 0° - 360°

With collet chuck – 1–16mm, ER25

With saw collet mount– D = max. 180 mm, d = 30 mm

Maintenance-free

Datenblatt

HSK-F 63 collet For horizontal drilling on

matrix table Distance between drill axis and

lower edge of housing: 7.8 mm Transmission ratio: 1:4 12,000 rpm

Rotateable from 0° - 360° 3 cylindrical drill collet

with clamping screw – 32 mm grid

(only in conjunction with C-axis with pneumatic system)

Datenblatt

HSK-F 63 Drilling / sawing / routing

45° (fixed) Transmission ratio: 1:1 12.000 rpm 1 spindle with collet chuck

1–16 mm, ER25 Rotation clockwise With saw blade mount

– D = max. 180 mm, d=30 mm Oil bath lubrication

Datenblatt

HSK-F 63 Transmission ratio: 1:1 12.000 rpm Pivot range 0° - 100° 1 spindle with collet chuck

– D = max. 180 mm, d=30 mm Rotateable from 0° - 360°

with C axis

Optional AggregatesNC-drill chuck

Datenblatt

Changing Units (Option)NC-drill chuck

HSK-F 63 24,000 rpm Clamping range 3-16 mm infinitely adjustable

ideal for intermediate sizes Collet chuck is eliminated

Optional AggregatesScoring Saw Unit

12- / 14- / 16-fold pick-up tool changer necessary HSK 63 F Scoring depth set manually using swivel arm Skew setting (scoring saw / main saw) via

setscrew and digital counter Specially matched tooling system

(scoring saw / main saw ground as a set)

Optional AggregatesScoring Saw Unit

Angle gear– Main saw Ø 250 mm, n(max.) 5.300 rpm– Scoring saw Ø 100 mm, n(max.) 15.900 rpm

– (only in combination with C-axis with pneumatic drive)

advantages:– excellent cutting results– Particularly suited for veneered panels coated with

laminate

CNC- Machining Centers Optional Aggregates. Aggregates nHigh torque through optimized gears nLittle...

Documents