Post on 20-Dec-2015
transcript
Electronics Manufacturing Processes
Manufacture of Electronics Components
Manufacture of Printed Circuit Boards (PCB’s)
Assembly of components on PCB’s
Electronics Manufacturing Processes
Manufacture of Electronics Components
Manufacture of Printed Circuit Boards (PCB’s)
Assembly of components on PCB’s
Electronics Component Manufacture
Electronics Components Mechanical and Electro-mechanical:
PCB mounted DIP switches, mains switches, disc drives
Passive Solid State Devices:Resistors, Capacitors
Active Solid State Devices:Transistors, Diodes, Thermionic valves, FETs and MOSFETs
Passive devices: resistors
Carbon Composite ResistorSlug leads mold bake seal- cheap, poor tolerance, rugged
Wire-wound resistorwind wire leads mold seal- high power, low resistance, high frequency apps
Film resistorFilm is cut by laser high precision- low frequency applications
Passive devices: capacitors
Tabbed tubular paper capacitor
Disk-ceramic capacitor Tubular ceramic capacitors
Active devices: Silicon wafer production
Quartzite (SiO2) + Carbon (C) + Heat + catalysts Si + CO2Raw Si:
Si + HCl SiCl4 + Hydrogen Fractional distillation
SiCl4 + H2 + catalysts Si + HCl
Pure Si:
Pure Monocrystalline Si:
Melt pure Si, Seed crystal drawn out slowly
Typical Single Crystal Ingot sizes:1-2m long, 8cm / 15cm / 30 cm diameter
Ingot sliced (Diamond saw)
Active Devices: Doping pure silicon
Silicon Dopant: Phosphorus, N-type Dopant: Aluminum, P-type
Doping processes:Diffusion (heat wafer in atmosphere with atoms of dopant)Ion implantation (ions of dopant are accelerated, bombard surface)
Diode (showing doping)
Active components: Transistors
NPN transistor
MOSFETMetal-Oxide SiliconField Effect Transistor
Active components: Integrated Circuits
Monolithic IC: Entire circuit made on a single crystal wafer
Hybrid IC: Monolithic IC + other components directly assembled into it
Hybrid micro-circuit film components
Active components: IC’s..
Depositing films of materials on substrate to make circuits
Thin Film Processes:
Form components on circuits by vacuum evaporation, sputtering, or anodizationFilm thickness is ≤ 5 m
Thick Film Processes (silk-screening)
Print liquid or paste through a screen (mask) onto substrate firing (baking) Film thickness is ~ 10 m
Silk-screening
IC’s: Resistive elements depositionvacuum deposition
Subtractiveprocess
Additiveprocess
Diffused Junction Process
- Photolithography is the most commonly used process- Photoresists: positive: more soluble when exposed negative: less soluble when exposed- Feature size = f(wavelength) small features need low radiation- Mask = = Artwork- Projection: - Direct: mask scale is 1:1 - Reducing: mask scale is 10:1
Packaging of components
- Packaging puts the chip (silicon) into a protective case
- Package provides external connections that are spaced conveniently (at distance, arranged in array) for soldering
Exploded view of TO package
Packaging of componentsStructure of a Surface mount component
SOIC packageSmall Outline IC
Avoiding possible heat damage to IC during soldering:
- Solder a chip carrier to the PCB - Insert chip into carrier
IC
Chip carrier
Integrated Circuit (IC) Manufacture
- Slicing the Silicon ingot- Fabrication of IC’s (Lithography, Sputtering, diffused junction, …)- Testing each IC on the slice
[source: www.towajapan.co.jp]
- Dicing (cutting each chip out with a diamond saw)- Packaging
Packaging
Dual Inline Package and its lead-frame
Steps in Lead Frame Manufacture:
(1) Cut copper strips(2) Clean in a chemical bath(3) laminate a layer of photoresist(4) Expose photoresist through mask(5) Develop and etch(6) Remove lamination(7) Plate internal regions with gold/silver
Dual Inline Package and its lead-frame
Steps in Lead Frame Manufacture:
(1) Cut copper strips(2) Clean in a chemical bath(3) laminate a layer of photoresist(4) Expose photoresist through mask(5) Develop and etch(6) Remove lamination(7) Plate internal regions with gold/silver
- Make leadframe
- Die attachment (chip bonded to leadframe using epoxy)- Wire bonding (ultrasonic welding)- Encapsulation (moisture resistant coating)- Molding (plastic package)
- Marking (chip number, co. name, marked on package [laser, silkscreen])- DTFS: deflash, trim the leadframe, form the leads, singulate (cut dambars)- Leadfinishing: electroplating the leads
Electronics Manufacturing Processes
Manufacture of Electronics Components
Manufacture of Printed Circuit Boards (PCB’s)
Assembly of components on PCB’s
PCB Manufacture
Types of PCB's single-side, double-side and multi-layer
Which type to use ?(a) Circuit complexity(b) Available space(c) Cost
Typical PCB
insulated substrate
copper connections
protective covering
Manufacturing glass reinforced epoxy resin copper-clad boards
Boards are produced in "clean-rooms"Manufacturing process: hot-pressing
• Place copper sheet on the lower plate• Place few layers of glass cloth impregnated with epoxy on top• [IF two-sided PCB's]: Place copper sheet on above• Press between steel plates in a steam-heated hydraulic press (~7,000,000 Pa) • Water cooling to 25º C• Trim to clean out extruded epoxy
• Punch/Drill holes for alignment• Make circuit on PCB (lithography)• Drill through holes (for component leads)
Multi-layer PCBs
• Similar process as single layer, but takes several steps
Schematics and features onMulti-layer PCB’s
Electronics Manufacturing Processes
Manufacture of Electronics Components
Manufacture of Printed Circuit Boards (PCB’s)
Assembly of components on PCB’s
PCB Assembly
- Insert leaded component into holes on PCB- Solder- Protective coating
Manual electronics assembly
Automated electronics assembly
Automated PCB Assembly
Component inputs:
Leaded Component IC’s, components with no wire leads
PCB Manufacture
Surface mount chip assembly:
- Silk-screening to apply solder paste on the board - Automated assembly of components (>30,000 components per hour) - IR or Wave soldering
Automatic soldering
Step 1. Application of the solder resistCover PCB with solder resist except Lands
Land
Step 2. Flux application
Foam fluxing Spray fluxing Ultrasonic Spray fluxing
Automatic soldering..
Step 3. Solder Application
Dip solderingDip soldering
Dual wave solder bath
Automatic soldering..
Step 4. Automatic removal of solder bridges: Hot air-jet knives
air-jet
Hot air jet knifeSOLDER
WAVE
air-jet
Hot air jet knifeSOLDER
WAVE
Types of circuit boards
Special considerationsfor SMT boards