Post on 16-Jul-2020
transcript
Installation InstructionsFor Pre-Attached Rosettes & Short PlatesPassage and Privacy
Door Handing - Rosettes and Short Plates
With step-by-step Installation Pictograms & Drilling Template
Applies to: • Classic and Rope Rosettes• Cottage and Studio Short Plates
Tools Required: #2 Phillips Screwdriver (Not power tools)
Door handing is critical for Split-Finish, or Split-Design products. It’s also used to determine where the Interior and Exterior halves of the lockset are located on the door. And, it’s used to position the latch tongue in relation to the strike plate.
INSTALLATION RULES:
1) Lockset machine mounting screws are inserted from the inside.2) Privacy pin holes are next to the door side containing the latch.3) Latch tongues have a beveled side, and this side should contact
the curved end of the face plate, and curved end of the strike plate.(See *Latch Tongue Note on page 3.)
Inside of Door - The Inside of a door refers to the side of the door that faces the room. For example, for a bedroom door on a hallway, the Inside of the door would face the bedroom.
Outside of Door - The Outside of a door refers to the side of the door that faces away from the room. The Outside of a door is generally more visible to visitors, and therefore a rosette on this side of the door has no visible screws. For example, on a bedroom door, the Outside would face the hallway.
outside
To identify door handing, face door from the Outside.
outside
DOORS OPENING INWARD
Hinge is on the left.Door is Left Hand.
Hinge is on the left.Door is Left Hand.
Hinge is on the right.Door is Right Hand.
Hinge is on the right.Door is Right Hand.
To identify door handing, face door from the Outside.
DOORS OPENING OUTWARD
outsideoutside
Page 1 - PK177 04202017
Exte
rior
Hal
f of
Lock
set
Spin
dle
Spin
dle
Butt
on
Lock
ing
Mec
hani
sm(T
hrea
ded
Priv
acy-
Pin
Hol
e)
Priv
acy
Pin
Hol
e
Priv
acy
Pin
Ant
i-Rot
atio
nBl
ock
1-1/
2” M
achi
ne S
crew
s(1
-3/8
” thi
ck d
oors
), or
1-3/
4” M
achi
ne S
crew
s(1
-3/4
” thi
ck d
oors
)
Latc
h
Latc
h To
ngue
Strik
e Pl
ate
3/4”
Fla
t Hea
dW
ood
Scre
ws
Face
plat
eEmer
genc
yRe
leas
e H
ole
Inte
rior
Hal
f of
Lock
set
Expl
oded
Dra
win
g fo
r Pre
-Att
ache
d Ro
sett
e/Sh
ort P
late
s Pa
ssag
e/Pr
ivac
y
Priv
acy
Emer
genc
yRe
leas
e Ke
y
Page
2 -
PK17
7 0
4202
017
Passage/Privacy
Installation InstructionsFor Pre-AttachedRosettes and Short Plates
Tools Required: #2 Phillips Screwdriver (Not power tools)
Fits doors1-3/8” to 1-3/4” thick
Attach the strike plate to the door jambusing 3/4” long wood screws.
DoorJamb
Install Strike Plate
Door - Inside
Screw in the Privacy Pin
(Privacy Only)
Install Privacy Pin
Door - Inside
Install interior half of lockset with 1-1/2” machine screws (1-3/8” thick doors), or 1-3/4” machine screws (1-3/4” thick doors)
Install Interior Half of Lockset
Door - Inside
InstallExteriorHalf ofLockset
Emergency Release Hole(Privacy Only)
Push spindle buttondown and hold during
insertion
1
2 Insert
Spindle
InsertSpindle
Door - Inside
LatchTongue
* Latch Tongue Note
Bevel Side
Face Plate Curve
Strike Plate Curve
Threaded privacy hubgoes on theinside of thedoor.
Bevel side of latch tongue shouldcontact curved end of face plate,and curved end of strike plate.
Install latch and rotate the latch tongue to change handing.(See page 1 for handing)
Install anti-rotation block. Be certain the arrow is pointing to the edge of the door.
Install faceplate with 3/4” wood screws.
(Anti-Rotation Block)
Arrow
1
2
3
Door - Inside See Latch TongueNote in next panel
*
*
InstallLatch
For 2-3/8” Backset:
For 2-3/4” Backset:
BacksetInformation
NOTE:
DRILLING TEMPLATES ON SEPARATE INCLUDED SHEET
Page 3 - PK177 04202017
MEA
SURE
FRO
M T
HE
FLO
OR
TO T
HE
CEN
TER
OF
EXIS
TIN
G L
OCK
S, A
ND
USE
TH
IS D
ISTA
NCE
AS
THE
CEN
TER
OF
THE
DU
MM
Y M
OU
NT.
IF
THER
EA
RE N
O E
XIST
ING
LO
CKS,
PO
SITI
ON
TH
E D
UM
MY
MO
UN
T 36
” TO
38”
FRO
M T
HE
FLO
OR.
(2) F
OLD
TEM
PLAT
E A
LON
G D
OTT
ED L
INE,
AN
D P
OSI
TIO
N F
OLD
ON
TH
E ED
GE
OF
THE
DO
OR.
T
APE
TEM
PLAT
E TO
FA
CE O
F D
OO
R.
(3) B
EFO
RE D
RILL
ING
VER
IFY
THE
BACK
SET
OF
YOU
R EX
ISTI
NG
DO
ORS
IN Y
OU
R H
OU
SE. D
RILL
PIL
OT
HO
LES
USI
NG
A 7
/64”
DIA
MET
ER B
IT.
(4) I
NSE
RT T
HRE
E W
OO
D S
CREW
S,
SL
IDE
ROSE
TTE
OVE
R M
OU
NT,
AN
D S
CREW
-ON
KN
OB.
(5) I
NSE
RT H
EX S
CREW
S
A
ND
TIG
HTE
N.
FLO
OR
DU
MM
Y M
OU
NT
(1)
TEM
PLAT
E
EDG
E O
F D
OO
RFACE
OF
DO
OR
Page
4 -
PK17
7
0420
2017