KX-TDE/NCP NEW FEATURES & FUNCTIONS VER -...

transcript

NEW FEATURES & FUNCTIONS VER.5

KX-TDE/NCP

New SLC (MCSLC) Card (KX-TDA1176/TDA1178) KX-TDE100/200 only KX-NCP500 Capacity Expansion KX-NCP500 only Maximum ICD-G Queuing : 30→100 Caller can exit from ICD-G Queuing Automatic start 2-way Recording Emergency Alert （SMDR) Conference Group with Auto-Answer Function One Touch Busy Override Tenant based ARS Improves Service Out Function CLIP when VM Transfer Incoming Call LCD Improves ICD Group Call Log Improves VM connection

New Features/Functions - 1 The new features/functions are available from, - KX-TDE100/200/600 MPR Ver.5. - KX-NCP500/1000 MPR Ver.5.

Improves SIP Trunk feature - T.38 disable mode is supported. - Forward CLIP (A-number) for SIP trunk - Refer Transfer is supported for SIP trunk - P-Asserted-Identity header is supported for SIP trunk - CODEC Priority Notification from SIP network - Improves FAX Connect ability - Redundancy Function is supported for SIP trunk - Delete alphabet Caller-ID

SIP Phone Feature RU/UA Model Only PCMC ID Lock

New Features/Functions – 2 The new features/functions are available from,

- KX-TDE100/200/600 MPR Ver.5. - KX-NCP500/1000 MPR Ver.5.

NEW SLC (MCSLC) CARDS KX-TDA1176 (MCSLC-16) KX-TDA1178 (MCSLC-24)

For KX-TDE100/200 (Ver.5)only

TDE100 Max. S Power 4 M Power 6

TDE200 Max. M Power 8 L Power 8

KX-TDA1176 (MCSLC16)

- 16 Port Single Line Telephone Ext. with Caller ID and Message Lamp Card

- KX-TDE0105 (MEC card) is needed.

- Standby power consumptions: 9W

One SLT goes to Off-hook mode, additionally 0.35W will be consumed.

- KX-TDE600 does NOT support KX-TDA1176.

Cable Maximum Distance ø 0.4 mm: 698 m ø 0.5 mm: 1,128 m ø 0.6 mm: 1,798 m CAT 5: 1,128 m

TDE100 Max. S Power 2 M Power 5

TDE200 Max. M Power 5 L Power 5

KX-TDA1178 (MCSLC24)

- 24 Port Single Line Telephone Ext. with Caller ID and Message Lamp Card

- KX-TDE0105 (MEC card) is needed.

- Standby power consumptions: 11W

One SLT goes to Off-hook mode, additionally 0.35W will be consumed.

- KX-TDE600 does NOT support KX-TDA1178.

Cable Maximum Distance ø 0.4 mm: 698 m ø 0.5 mm: 1,128 m ø 0.6 mm: 1,798 m CAT 5: 1,128 m

PBX Power unit

SLT Capacity Ver. 4

SLT Capacity Ver.5 New

KX-TDE100 (6 Slot)

S 64 = 16x4 64 = 24x2 + 16x1

M 96 = 16x6 128 = 24x5 + 8x1

KX-TDE200 (8 Slot for Extension)

M 128 = 16x8 128 = 24x5 + 8x1

L 128 = 16x8 168 = 24x5 + 16x3

KX-TDA1176/1178 (MCSLC16/24) Maximum SLT capacity of KX-TDE100/200 is as follows.

KX-NCP500 CAPACITY EXPANSION

KX-TDE/NCP Version 5

NCP500 Ver.5

The current NCP500 hardware with Ver.5 software can support the below specification.

NCP500 Ver. 4 NCP500 Ver. 5 NCP1000 Ver.4/5

Telephone

Max. 156 172 172 SLT 24 36 *) 36 DT3xx/T76xx 20 40 W/DXDP 40 T7650/T7656 20 36 36 Other DPT 6 10 10 APT 4 4 4 IP-PT 128 128 128 SIP Ext. 128 128 128

DSS console 8 8 8

Max. 32 32 32 2ch CS 7 11 11 8ch CS **) 3 5 5 IP-CS **) 16 16 16

Power Factor (Software S/W) 28 44 44 PS 64 64 64

NCP500 Capacity Expansion

*) 2 x DLC16 or SLC16 Required = Cannot use OPB3 (& Door phone card)

**) One 8ch CS counts as 2 x 2ch CS.

CS Power unit and System total number of CS NCP500 Ver. 4 NCP500 Ver. 5 NCP1000 Ver.4/5

Max. CS Power units 32 32 32 2ch CS 1 1 1 8ch CS 2 2 2 IP-CS 2 2 2

System total number of CS 19 21 21

NCP500 Ver. 4 NCP500 Ver. 5 NCP1000 Ver.4/5 2ch CS 7 11 11 8ch CS 3 5 5 IP-CS 16 16 16 PS 64 64 64

NCP500 Capacity Expansion NCP500 Ver.5

The current NCP500 hardware with Ver.5 software can support the below specification.

MAXIMUM ICD-G QUEUING: 30→100

ICD-G 600

CO Queuing Table Max. 30

Default : 30

Queuing Table Max. 100

No Optional Programming

Maximum ICD-G Queuing : 30 → 100 Before Ver.5 (Max. 30)

TDE/NCP Ver.5 (Max. 100)

CALLER CAN EXIT FROM ICD-G QUEUING

OGM-1: Welcome to Panasonic….. OGM-2: Please wait for the moment.

Customer Request function

External call

The user wants to exit from the queuing and leave a message in the mail box.

Cycles forever

Caller can exit from ICD-G Queuing Before Ver.5

Once an external call goes into an ICD-G queuing table, the caller has only two options, wait for the call to be answered by the ICD-G agent or disconnect the line.

External call

Ext.202 Dial “2”

No AA Service

- Only AA is available (not DISA - dial extension number). - When the caller is listening to the BGM/MOH (wait

period), the DISA AA function does not work.

Caller can exit from ICD-G Queuing TDE/NCP Ver.5

The ICD-G Queuing OGM performs not only sending OGM but also DISA AA service. When the caller is listening the OGM, the caller can exit to an extension specified by AA.

ICD-G: 601

VM Group:500

Mail Box: 601

DISA 502: Dial 0 → 500

Caller can exit from ICD-G Queuing TDE/NCP Ver.5 + If a VM is connected to the PBX

If a system has a VM and an ICD-G has a VM mail box, the caller has three options, wait for the call to be answered by the ICD-G agent, disconnect the line or leave a message to a mail box.

External call

OGM-1: Welcome to Panasonic….. OGM-2: Please wait for the moment. Or dial “0” to leave voice message.

VM Mail Box 601

Dial “0”

Add Message

Caller can exit from ICD-G Queuing TDE/NCP Ver.5 + If a VM is connected to the PBX

TDE/NCP Ver.5 + If a VM is connected to the PBX

VM custom service is also available

Program Point

VM Custom Service

Dial “0”

VM Group:500

Custom Service

DISA 502: Dial 0 → 500

External call

Select

Caller can exit from ICD-G Queuing

ICD-G: 601

Dial Dial

Caller can exit from ICD-G Queuing Limitation

Only when the caller is listening the OGM (OGM-2), the caller can exit to the extension specified by AA. When the caller is listening the BGM/MOH (wait period), the OGM-2 DISA AA function does not work.

Counter Idea

Change wait period to OGM-3 (OGM-3 records MOH/BGM)

- VM in other PBX (Centralized VM) can NOT be DISA-AA destination.

VM Group: 500

VM Group

D-PT integration

DISA 502: Dial 0 → 500

Centralized VM

Caller can exit from ICD-G Queuing TDE/NCP Ver.5 Technical Condition

- VM has to be KX-TVA/TVM using Digital (PT) integration.

1.External call

ESVM:599

ICD-G: 601

DISA 502: Dial 0 → 599

Ext.2002

Ext.2003

Ext.2001

2. Dial 0

3. Go to Ext.2001 SVM

- Ext.2001 has to have an SVM box. - A setup of C-FWD to SVM on Ext.2001 is not necessary.

The SVM of the 1st ICD-G member will answer after the caller dials digit 0.

ESVM box

Caller can exit from ICD-G Queuing What if a Customer wants to use ESVM for recording a message?

ESVM floating extension number can be assigned in the DISA AA destination.

AUTOMATIC START 2-WAY RECORDING

1- Call to Ext.2001

Ext.2001

Three party conference

1- Call to Ext.2001 2- Ext.2001 answers the call. 3- The PBX starts 2 way recording automatically.

2- Answer

3- 2-way Recording

Before Ver.5 1- Call to Ext.2001 2- Ext.2001 answers the call. 3- Press “2-way recording” button to start 2 way recording.

Automatic start 2-way Recording TDE/NCP Ver.5

Manual Recording

Condition - PT(IP/Digital/Analog), PS and SLT can use this function. - SIP Phone can NOT use this function. - Internal call/External call/ICD-G call is automatically recorded. - Incoming call/Outgoing call is automatically recorded. - We cannot change the above-mentioned conditions (E.g. Only external incoming call is automatically recorded) - Programming “2-way recording” button is not necessary. If you program a 2-way recording button, it can be used to stop and then re-start 2-Way recording”.

Once it is programmed it will always start automatically “2-way recording”. A manual start cannot be performed.

Automatic Recording

Automatic start 2-way Recording TDE/NCP Ver.5 (New Program Item)

Automatic start 2-way Recording Technical Specifications

The Max. number of simultaneous recordings

NCP/TDE100,200 TDE600 (Basic) TDE600 (Basic)

+ 3 x TDE620

Max. 10 10 40

Condition 3 x TVM50 1 x TVM200

3 x TVM50 1 x TVM200

2 x TVM200

– A maximum of 10 calls can be recorded to VM for NCP and TDE100/200 at the same time (PBX supports 10 x 3 conference)

– A maximum of 24 calls can be recorded to one VM for TDE600, because one VM supports 24ch.

– A maximum of 40 calls can be recorded to two or more VM for TDE600, because TDE600 supports10 x 3 conference hardware per cabinet.

– VM has to be KX-TVA/TVM using Digital (PT) integration.

– VM DTMF integration does NOT support automatic recording.

– Centralized voice mail does NOT support automatic recording.

– E-SVM card cannot be used this function.

Ext.2002

All operator conversation

Ext.2001

Manager

Ext.1001

Mail Box Ext. No 201 1001

Programming Point

Automatic start 2-way Recording TDE/NCP Ver.5

It is also possible to record all of the conversation to one mail box.

• Ext.1001 (Manager) has a mail box 201.

• Ext.2001, Ext2002 (Operator) conversation can be recorded on the mail box 201.

• Only Ext.1001 can listen to the recorded message.

EMERGENCY ALERT (SMDR) KX-TDE/NCP Version 5

Before Ver.5 After finishing the call, this extension number is outputted to SMDR, only.

“Emergency Dial” table

Ext.2001

SDMR (RS232C/LAN)

Emergency Call

Ver.5 New

Emergency Alert (SMDR) TDE/NCP Ver.5

If a dialed number is matched with the “Emergency Dial” table, when dialing is completed, the extension number is outputted to SMDR (1st SDMR). Also, after finishing the call, this extension number is outputted to SMDR (2nd SMDR).

Option Ver.5 function

Default Ver.4 function

Emergency Alert (SMDR) Related Programming

“Emergency Dial” table SDMR

(RS232C/LAN)

CA Call Account

If the CA call account software is installed to a PC, we can see an Emergency call alert by a popup window, after dialing is completed. - Version up is NOT required for CA Call Accounting

software.

Emergency Alert (SMDR)

Ext.2001 Emergency Call

CONFERENCE GROUP WITH AUTO-ANSWER FUNCTION

1.Dial *321#

Ext.2003 Ext.2001 Ext.2002

Auto-Answer=ON

Conference Group No.1

3. Speaker is automatically ON

Ext.1001

2. Call

4. Paging

Have to

The “Auto Answer” setting is a necessity!!!

Conference Group with Auto-Answer Before Ver.5

1. Ext.1001 holds a conference (*321#)

2. The PBX calls pre-programmed DECT-PS

3. All DECT PS on the conference group automatically answers.

Speaker phone is automatically “ON”.

4. Ext.1001 user can page.

Condition: All PS have to be set to “Auto-Answer” = ON.

1.Dial *321#

Ext.2003 Ext.2001 Ext.2002

Auto-Answer=ON

Ext.1001

2. Call

4. Paging

2. The PBX calls a pre-programmed DECT-PS

3. All DECT PS on the conference group automatically answer.

Speaker phone is automatically “ON”.

Condition: System programming is required.

Regardless of “Auto Answer” = ON/OFF

Please set “Enable”

Conference Group with Auto-Answer New Program Item and Functionality

1.Dial *321#

Ext.2003 Ext.2001 Ext.2002

Ext.1001

2. Call

4. Paging

2. The PBX calls a pre-programmed DECT-PS

3. All DECT PS on the conference group automatically answer. Speaker phone is automatically “ON”.

5. An answer (DECT-PS) is possible by pressing any keys.

Condition: System programming is required.

5. Press any keys

Please set “Enable”

Broadcast Mode Ability to Talk Auto-Answer Extension function

Answer Mode Talk Mode Disable Enable Disable Manual Answer Both way Disable Enable Enable Auto-Answer Both way Enable Disable Disable Manual Answer One way Enable Disable Enable Auto-Answer One way

Enable Enable Disable Manual-Answer One way → Press any key → Both way

Enable Enable Enable Auto-Answer One way → Press any key → Both way

Conference Group with Auto-Answer New Program Item and Functionality

1.Dial *321#

Ext.2003 Ext.2001 Ext.2002

Ext.1001

2. Call

4. Paging

This function also works on a D-PT.

Conference Group with Auto-Answer TDE/NCP Ver.5

2. The PBX calls a pre-programmed D-PT

3. All D-PT’s on the conference group automatically answer. Speaker phone is automatically “ON”.

Regardless of “Auto Answer” = ON/OFF

ONE TOUCH BUSY OVERRIDE

Ext.2002

1- Ext.2001 is talking to an external person on SCO-1. 2- Ext.2002 press the SCO-1 button → Busy Tone 3- Ext.2002 press “3” or “OVER” for overriding the call.

Ver.5 (System option = ON) 1- Ext.2001 is talking to an external person

on SCO-1. 2- Ext.2002 press the SCO-1 button →

Overriding the call.

Ext.2001

1- Talking

Default : Disable

New Program Item

One Touch Busy Override Before Ver.5

TENANT BASED ARS KX-TDE/NCP Version 5

Tenant-B UK

Company

International call Provider :BT

Tenant-A Japanese Company

International call Provider :KDDI

Customer needs a tenant base ARS reading table.

Tenant based ARS Before Ver.5 ARS function

All ARS reading tables are all for tenants,

Customer Request function (Sample) One PBX is shared with two or more companies. The companies have a contract with different telephone carriers.

Japanese company has to use KDDI for international call.

→ Dial +1 (USA call) → KDDI Line

UK company has to use BT for international call.

→ Dial +1 (USA call) → BT Line

KDDI BT

TDE600 Applied ARS Leading Digits Table Tenant 1 2 -- 19 20 21-32 Leading Digits Table 1-50 51-100 -- 901-950 951-1000 1-1000

Tenant Base

If the tenant ARS mode is selected to “Enable”,

TDE100/200/NCP Applied ARS Leading Digits Table Tenant 1 2 -- 7 8 - Leading Digits Table 1-50 51-100 -- 301-350 351-400 401-1000 (Not used)

Tenant based ARS TDE/NCP Ver.5

TDE-NCP version 5 supports tenant Independent ARS table.

TDE600 Applied ARS Leading Digits Table Tenant 1 2 -- 19 20 21-32 Leading Digits Table 1-1000

If the tenant ARS mode is selected to “Same as System Setting”, the PBX checks “8-1 System Setting”, applied ARS Leading Digits Table is as follows.

TDE100/200/NCP Applied ARS Leading Digits Table Tenant 1 2 -- 7 8 - Leading Digits Table 1-1000

Tenant based ARS TDE/NCP Ver.5

IMPROVED SERVICE OUT FUNCTION

“Extension dial lock” : Ver.4/5 “DND” : Ver.4/5 “Display Lock” : Ver.5

Need the extension PIN

Other user cannot see call log and cannot listen to SVM message.

Improved Service Out Function Before Ver.5 Service Out status

“Extension dial lock” and “DND” are assigned automatically by “Service Out” operation. Therefore other users can see the call log and listen to the SVM message.

TDE/NCP Ver.5 Service Out status

“Extension dial lock”, “DND” and “Display Lock” are assigned automatically by “Service Out” operation.

Improved Service Out Function How to un-lock

NB: Input an extension PIN (Default: Blank) before use this function.

CLIP WHEN VM TRANSFER KX-TDE/NCP Version 5

Ext.2001

1. Call

Ext.1001

System Programming 2.9 System Options → Option 4

CLIP:4771111

2. Transfer

Centralized VM

CLIP:4771111 VM Ext. Number

CLIP when VM Transfer Before Ver.5

When a VM transfers a CO call to a remote extension, The CLIP information form the VM is dependant upon the system programming.

VoIP-Net

Note: Ext.1001 (Local extension) receives always CLIP: 4771111, regardless of programming.

CLIP when VM Transfer TDE/NCP Ver.5

The remote extension receives always the CO CLIP, regardless of the system programming.

Ext.2001

1. Call

Ext.1001

System Programming 2.9 System Options → Option 4

CLIP:4771111

2. Transfer

Centralized VM

CLIP:4771111

VoIP-Net

CLIP:4771111

Option Bit: 0C-5 0C-5=Disable: TDE/NCP Ver.5 (Default) 0C-5=Enable: Before TDE/NCP Ver.5

CLIP when VM Transfer TDE/NCP Ver.5

If a customer likes the previous function, please change the option bit 0C-5 to “Enable”

INCOMING CALL LCD KX-TDE/NCP Version 5

Incoming Call LCD Before Ver.5

If a caller name or ID / DID name / CO line number is displayed on PT LCD. They can be switched by the “Transfer” key or the “INFO” soft key. If the user presses the button by accident, this can become confusing, because last mode is stored and displayed, when the next call arrives.

TDE/NCP Ver.5

TDE-NCP Ver.5 does not the save display mode, even after PT operation. - Display switch operation itself is kept. - Display mode can be assigned using PCMC. - “Automatic save after PT operation” is controlled by the PCMC system reserved bit. This is now default and new specification for this function.

Default (Disable)

Option Bit: 06-5 06-5=Disable: TDE/NCP Ver.5 (Default) 06-5=Enable: Automatic save after PT operation

Incoming Call LCD TDE/NCP Ver.5

IMPROVED ICD GROUP CALL LOG

TDE/NCP Ver.5 TDE-NCP Ver. 5 records ICD group call, when the call is overflowed to VM.

Ext.1001

1. Call 2. OVF

3. VM Answer

4. Disconnect

ICD-G Log Key

Improved ICD-G Call Log Before Ver.5

1- If an incoming call goes to an ICD-G.

2- If a member of ICD-G does not answer, the call is OVF to a VM,

3- The VM answers the call.

4- If the caller disconnects the line before the VM starts the message recording.

→There is No call log on the system (ICD-G Log key or VM).

Default: Disable

1. Call 2. OVF 3. VM Answer 4. Disconnect (Before VM

message recording)

1. Call 2. OVF 3. VM Answer 4. Disconnect (After VM message

recording)

1. Call 4. Disconnect (Before OVF)

Disable No Call Log No Call Log Call Log

Enable Call Log Call Log Call Log

If the OVF destination is a VM

Improved ICD-G Call Log TDE/NCP Ver.5 New Option

Ext.1001

1. Call 2. OVF

3. VM Answer

4. Disconnect

ICD-G Log Key

Default: Disable

If the OVF destination is a VM

Improved ICD-G Call Log TDE/NCP Ver.5 New Option

Ext.1001

1. Call 2. OVF

3. VM Answer

4. Disconnect

ICD-G Log Key

1. Call 2. OVF 3. D-PT answer 4. Disconnect

1. Call 2. OVF 3. D-PT does not answer 4. Disconnect

1. Call 4. Disconnect (Before OVF)

Disable No Call Log Call Log Call Log

Enable Call Log Call Log Call Log

IMPROVED VM CONNECTION

Disable

1. Call AA

Service

Enable

1. Call Mailbox Service

AA Service

2. OVF 1. Call

Customer Request function

ICD-G OVF → AA Service

Extension Intercept →Mailbox

Improved VM connection Before Ver.5

There is one optional item to control the VM function, when an incoming call is intercepted (OVF) to the VM from the Ext. (ICD-G).

2. Intercept

1. Call AA

Service

2. Intercept

AA Service

2. OVF 1. Call

Improved VM connection TDE/NCP Ver.5

Two optional items to control VM function, when an incoming call is intercepted (OVF) to VM from the Ext. (ICD-G).

Disable

Enable

Disable

Enable

This option has an effect for external calls only, not for internal calls.

- T.38 DISABLE MODE IS SUPPORTED. - FORWARD CLIP (A-NUMBER) FOR SIP TRUNK - REFER TRANSFER IS SUPPORTED FOR SIP TRUNK - P-ASSERTED-IDENTITY HEADER IS SUPPORTED FOR SIP TRUNK - CODEC PRIORITY NOTIFICATION FROM SIP NETWORK - IMPROVES FAX CONNECT ABILITY - REDUNDANCY FUNCTION IS SUPPORTED FOR SIP TRUNK - DELETE ALPHABET CALLER-ID

Improvement features of SIP Trunk

New Program Item

Improves SIP Trunk feature (TDE/NCP Ver.5)

T.38 disable mode

Before Ver.5

For out going FAX We can select “enable”/”disable” T.38 function.

For incoming FAX We cannot select “enable”/”disable” T.38 function.

→ When un-compatible T.38 incoming FAX arrives the system, the FAX connection will be failed.

TDE-NCP Ver.5

For out going FAX We can select “enable”/”disable” T.38 function.

For incoming FAX We can select “enable”/”disable” T.38 function.

→ Un-compatible T.38 incoming FAX → Please set “Disable” → G.711 mode

1. Call TDE/NCP

CLIP:8821111 C-FWD to CO

CLIP:4771111 INVITE: CLIP Information ?

Forward CLIP (A-number)

When the SIP trunk incoming call is forwarded to a mobile network through the SIP trunk, incoming CO callers CLIP (A-number) can be sent using the diversion header feature.

SIP-Provider

Before Ver.5

CLIP We can select the extension CLIP or the Caller CLIP.

TDE-NCP Ver.5

CLIP We can select the extension CLIP or the Caller CLIP.

And the PBX sends the Caller CLIP by the diversion header element (Select System Option).

New Program Item

Forward CLIP (A-number) (New Program Item)

NB: SIP IOT is strongly required before this is set to “Enable” !

SIP-Provider

3.Connect

TDE/NCP

Ext.1001

1. Talking TDE/NCP

Ext.1001 2. Refer Transfer

4.Voice paths are released

-Attended Transfer -Blind Transfer

External Caller

Refer Transfer

When a TDE/NCP Ver. 5 extension makes a call, the caller can transfer the call to another external party through the SIP trunk by using the Refer Transfer feature.

Blind Transfer

Attended Transfer

Refer Transfer (Operation differences)

New Program Item

Refer Transfer (New Program Item)

NB: SIP IOT is strongly required before set to “Yes” !

SIP-Provider

TDE/NCP

Ext.1001 External Caller

2. Refer Transfer to Ext.1002

1. Talking

Refer Transfer (Condition)

TDE/NCP Ver. 5 does not support a refer transfer request from the SIP provider.

SIP-Provider

INVITE Message Header (TDE/NCP Ver.5)

Make a call TDE/NCP

INVITE Message

P-Asserted-Identity Header

TDE/NCP Ver.5 supports the P-Asserted-Identity header.

New Program Item

P-Asserted-Identity Header (New Program Item)

New Program Item

Enable: SIP network CODEC Disable: PBX CODEC (Default)

CODEC Priority Notification

Before Ver.5

When the PBX receives a SIP call from the SIP network, the PBX CODEC selection is first priority against SIP network request.

TDE/NCP Ver.5

CODEC priority is selectable (PBX CODEC or SIP network CODEC )

System Programming

2.9 System Options → Option 2

SIP-Provider

FAX Call

TDE/NCP

Support Super G3 DSP NLP setting DSP Echo setting

Before Ver.5 No No changed No changed

TDE/NCP Ver.5 YES OFF (Automatic) OFF (Automatic)

DSP NLP setting DSP Echo setting

Before Ver.5 No changed No changed

TDE/NCP Ver.5 OFF (Automatic) No changed

G3 FAX

Support Super G3 FAX

Improves FAX Connect ability

TDE/NCP Ver.5 supports Super G3 FAX function over SIP trunk.

SIP-Provider

Redundancy Case-1

SIP-Server-2

TDE/NCP SIP-Server-1 1. Call

Redundancy Case-1

SIP-Server-2

Redundancy Function

TDE/NCP Ver.5 supports the redundancy function in two cases.

SIP-Provider

SIP-Server-2

New Program Item

Timer Value=0: Disable Redundancy Timer Value ≠0: Enable Redundancy

Redundancy Function (New Option Program)

Redundancy Case-1

New Program Item

Disable: Disable Redundancy Enable: Enable Redundancy

Redundancy Function (New Option Program)

Redundancy Case-2

SIP-Provider

SIP-Server-2

NB: SIP IOT is strongly required before set to “Yes” ! It should not be “0”

SIP-Provider

Make a call

TDE/NCP

INVITE Message CLIP: 0924771234aaaaa

Delete data

CLIP 0924771234

Deletion alphabet Caller-ID

When an alphabet characters are contained within the CLIP information, in the INVITE message, these alphabet character’s are deleted.

SIP PHONE FEATURE KX-TDE/NCP Version 5

Before Ver.5

TDE-NCP does not support verification code feature for SIP phone.

TDE/NCP Ver.5 TDE-NCP version 5 supports verification code feature for SIP phone.

SIP Phone Feature

PCMC ID LOCK (RU/UA MODEL ONLY)

Model Registration Specifications

TDA100D 16-digit ID is required to PCMC. ID is provided to only authorized dealer from Panasonic CIS. ID for TDA100D and ID for TDE-NCP are different.

ISDN/DECT/TIE programming is not allowed before registration.

TDE-NCP Version 5

All programming is not allowed before registration. In Russia a dealer has to disclose the PBX password to the user by law . The user can inform the password to an unauthorized dealer, if maintenance fee is cheaper. However the unauthorized dealer cannot program PBX from version 5.

NS1000

The activation key is required in the PBX. The activation key is provided from PSN key management system. The activation key is only provided to authorized dealer s free of charge. Validity of the activation key is 6 months.

PCMC ID Lock TDE/NCP Ver.5

TDE-NCP version 5 supports PCMC ID lock for NCP500-1000RU/UA, TDE100-200RU/UA and TDE600RU/UA.

PC MAINTENANCE CONSOLE (PCMC) FOR TDE-NCP

Please use U-PCMC Ver. 7.2.x.x

KX-TDE600 Ver. 7.2.x.x or later

KX-NCP500/1000 Ver. 7.2.x.x or later

KX-TDE100/200 Ver. 7.2.x.x or later

PCMC for KX-TDE/NCP Ver.5.

THANK YOU VERY MUCH FOR YOUR ATTENTION!

KX-TDE/NCP NEW FEATURES & FUNCTIONS VER -...

Documents