Post on 06-Apr-2018
transcript
8/2/2019 Lab Manual Mechanics-II
1/26
Engineering Mechanics-II
Lab Manual
Department of Mechanical Engineering
International Islamic University Islamabad
1
8/2/2019 Lab Manual Mechanics-II
2/26
Experiment No: 01
Layout of Engineering Mechanics-II Lab
Layout: The setting of apparatus in specific order is called layout.
Product Layout: Arrangement as per required product.
Process Layout: Layout as specified process.
1. Square and V-thread: An apparatus to compare the efficiencies of square andV-thread.
2. Fly Wheel: Fly wheel is device to control the motion or reduce fluctuation.Application in fuel control, aero plane fuel rod.
3. Linear and Angular Velocity: Apparatus convert linear velocity into angularvelocity and vice versa.
4. Screw Jack: Used to lift load. To find efficiency and mechanical advantage ofscrew jack.
5. Inclined Plane: An apparatus used to find mechanical advantage of inclinedplane at different angles. To compare mechanical advantage of different angles.
6. Derrick Crane: It is also called moveable crane. It is used to lift heavy loads.7. Western Differential Pulley: Device to lift heavy loads through differential
gears.8. Worm and Worm Wheel: Device used to convert translational motion into
transverse motion.
2
8/2/2019 Lab Manual Mechanics-II
3/26
Experiment No. 02
a. To determine Mechanical Advantage of Inclined Plane.b. To compare Actual and Ideal Mechanical Advantage.
Theory:
Mechanical Advantage: Assessment of effective forces on rigid bodies is called
mechanical advantage.
Inclined Plane: Archimedes 3 century B.C discovered six simple machines. Inclined
plane is one of them. A flat/smooth surface which has ends at different heights is called
inclined plane.
Apparatus:
Inclined plane, pulley, weights, protector, meter rod, scale pan and spring balance.
Procedure:
First of all found the weight of trolley or roller and the scale pan with the help of
spring balance. Than clean the surface of inclined plane and adjusted to angle of 30.
Then I connected the trolley and the scale by a thread, which pass over a pulley. Then I
placed the trolley in middle of inclined plane and scale pan hangs freely. Then I
adjusted the weight in the scale pan till on gently tapping the inclined plane. The trolley
just moved I noted the readings i.e. P and W. Then I calculated the mechanical and
ideal advantage by formula
3
8/2/2019 Lab Manual Mechanics-II
4/26
M.A= W/P, I.M.A=l/h
Precautions:
1. Same inclination of load should be avoided.2. Load holder should be at center of plane.
Calculations:
Length of inclined plane= l
Height of upper end= h1
Height of lower end= h2
Height= h = h1-h2
Real mechanical advantage= l/h
S/No W(N) P(N) Angel I.M.A A.M.A
4
8/2/2019 Lab Manual Mechanics-II
5/26
Experiment #03
1-To compare actual and ideal mechanical advantage of inclined plane.
2-To derive relationship between angle and mechanical advantage (actual and
ideal) at different angles.
Apparatus:
-inclined plane
-pulley
-weight
-protector
-meter rod
-scale pan
-spring balance
Theory
Inclined plane:
An inclined plane is a flat surface that higher at one end. It make of moving things
easier
Mechanical advantage:
M.A is the ratio of output distance and input distance.
i.e M.A=output/input
Difference between ideal and actual mechanical advantage
In ideal mechanical advantage friction is ignored while in actual mechanical advantagefriction is considered.
Mechanical advantage of inclined plane
The mechanical advantage of inclined plane is equal to the length of slope divided by
the height of the inclined plane.
5
8/2/2019 Lab Manual Mechanics-II
6/26
Procedure:
First of all I found the weight of roller and scale pan with the help of spring balance.
Then I clean the surface of inclined plane and adjusted to an angle of 11 degree. Then I
connected the trolley and scale pan by thread, which passes over pulley. Then I placed
the trolley in middle of inclined plane, and inclined plane hangs freely. I placed load and
effort and noted the reading when moving just started
Thus finding value of p and w putting in formulas a.m.a=w/p and i.m.a=l/h get these
required advantages. We see that I.M.A and A.M.A are inversely proportional to angle.
Precautions:
1-roller should be placed at middle of inclined plane
2-reading should be taken at that time when movement starts.
3-mishanding should be avoided
4-angle should be adjusted carefully
Comments:
It is noted that I.M.A and A.M.A are different because friction is ignored in actual
mechanical advantage.
Table
s/no angle W(n) P(n) l h A.M.A I.M.A
6
8/2/2019 Lab Manual Mechanics-II
7/26
7
8/2/2019 Lab Manual Mechanics-II
8/26
Experiment #04
To determine the mechanical advantage of screw jack
Apparatus:
-screw jack
-weights
-hanger
-thread
Jack (device)
A jack is a mechanical device used to lift heavy loads or apply great forces.
Mechanical jack
A mechanical jack is a device which lifts heavy equipment. The most common form isa car jack, floor jack or garage jack which lifts vehicles so that maintenance can beperformed. Car jacks usually use mechanical advantage to allow a human to lift avehicle by manual force alone. More powerful jacks use hydraulic powerto providemore lift over greater distances. Mechanical jacks are usually rated for a maximum
lifting capacity (for example, 1.5 tons or 3 tons)
Hydraulic jack
A hydraulic jack uses a fluid, which is incompressible, that is forced into a cylinder by apump plunger. Oil is used since it is self lubricating and stable. When the plunger pullsback, it draws oil out of the reservoir through a suction check valve into the pumpchamber. When the plunger moves forward, it pushes the oil through a discharge checkvalve into the cylinder. The suction valve ball is within the chamber and opens witheach draw of the plunger. The discharge valve ball is outside the chamber and openswhen the oil is pushed into the cylinder. At this point the suction ball within the chamber
is forced shut and oil pressure builds in the cylinder.
Pneumatic jack
A pneumatic jack is a hydraulic jack that is actuated by compressed air - for example,air from a compressor - instead of human work. This eliminates the need for the user toactuate the hydraulic mechanism, saving effort and potentially increasing speed.
8
http://en.wikipedia.org/wiki/Mechanical_advantagehttp://en.wikipedia.org/wiki/Hydraulic_machineryhttp://en.wikipedia.org/wiki/Tonhttp://en.wikipedia.org/wiki/Hydraulic_machineryhttp://en.wikipedia.org/wiki/Tonhttp://en.wikipedia.org/wiki/Mechanical_advantage8/2/2019 Lab Manual Mechanics-II
9/26
Sometimes, such jacks are also able to be operated by the normal hydraulic actuationmethod, thereby retaining functionality, even if a source of compressed air is notavailable
Screw jack
It is the most important and 90% used jack because it has ability of self locking. It isused to lift houses from foundation. The screw is pushed upward until l desired height isreached.
9
8/2/2019 Lab Manual Mechanics-II
10/26
Procedure
1-wrap the string round the circumference 0f the flanged table and pass it over thepulley
2-attach hanger to free end of the string
3-the weight which is placed on the head of screw is called load (w) and the weightwhich is placed in the hanger is called effort(p)
4-note the initial readings of w and p
5-note reading when moment starts.
6-repeat process three times varying w and p
7-draw graph between w and M.A
8-Draw graph between p and M.A
TABLE
s/no W(N) P(N) M.A=W/P
PRECAUTIONS
1-String should not be flexible to avoid extension
2-wraping string should be such that it ends at lower part of flanged table Comments
It was very simple experiment and we enjoy it.
10
8/2/2019 Lab Manual Mechanics-II
11/26
Experiment No: 05
To compare efficiencies of square and V-thread
Apparatus:
Square and v-thread apparatus, weights, hangers, steel rule, string.
11
8/2/2019 Lab Manual Mechanics-II
12/26
Theory:
A thread is a grove or removal of surface in specific order and angel. The square
thread form is common thread form for lead screws. It gets its name from the square
cross section of the thread.
The v-thread gets its name from the v like cross section of the thread. This thread wad
invented by Soviet Climber. Square thread has less life than v thread because of the
fact that square thread have greater contact area, hence greater friction and hence
more worn and tear.
Efficiency:
% E= W/P.V *100
Where W is load or resistance force, p is the effort force an v is the velocity ratio.
Velocity ratio= Distance moved by effort/ Distance mobbed by load.
Procedure:
1. First work the screw on the square thread.2. For one complete turn of a table, the effort works through the circumference of
the table and the load rises through the pitch of the square thread. Measurethese and calculate the velocity ratio v.
3. Now find the effort p that is just sufficient to raise the load w applied to the screw.
Do this for w= 0, 5, 10, 15..4. For each reading calculate the % efficiency.5. Next work the screw on the v-thread and calculate the corresponding velocity
ratio v.6. Applying the same set of loads. Find the respective corresponding efforts and
calculate the efficiency for each reading.
S/N0 Load W Effort P Efficiency=w/pv*100
Square V-thread square v-thread
Precautions:
1. Determine pitch of the screw carefully.2. Take care that effort is applied in such a way that the load is just raised and not
lowered.3. Before performing experiment check that apparatus is ok by turning the table by
hand.Experiment No: 06
12
8/2/2019 Lab Manual Mechanics-II
13/26
a. To compare efficiencies and M.A of square and v-thread.b. To draw relationship between n and M.A with the help of graph.
Apparatus:
Square and v-thread apparatus, weights, hangers and strings.
Theory:
A thread is a grove or removal of surface in specific order and angel. The square
thread form is common thread form for lead screws. It gets its name from the square
cross section of the thread.
The v-thread gets its name from the v like cross section of the thread. This thread wad
invented by Soviet Climber. Square thread has less life than v thread because of the
fact that square thread have greater contact area, hence greater friction and hencemore worn and tear.
Efficiency:
% n= W/P.V *100
Where W is load or resistance force, p is the effort force an v is the velocity ratio.
Velocity ratio= Distance moved by effort/ Distance mobbed by load.
Mechanical Advantage is the number of times a machine multiplies the input force. M.A
for square and v-thread is calculated by formula M.A=w/p.
Procedure:
1. First work the screw on the square thread.2. For one complete turn of a table, the effort works through the circumference of
the table and the load rises through the pitch of the square thread. Measurethese and calculate the velocity ratio v.
3. Now find the effort p that is just sufficient to raise the load w applied to the screw.Do this for w= 0, 5, 10, 15..
4. For each reading calculate the % efficiency.
5. Also calculate mechanical advantage for each reading.6. Next move the screw on the v-thread and calculate the corresponding velocity
ratio v.7. Draw graphs between M.A and w, M.A and p and also M.A and n.
S/No Effort p Efficiency=w/pv*100 M.A=w/p
13
8/2/2019 Lab Manual Mechanics-II
14/26
Precautions:
1. Determine pitch of the screw carefully.2. Take care that effort is applied in such a way that the load is just raised and not
lowered.3. Before performing experiment check that apparatus is ok by turning the table by
hand.
14
8/2/2019 Lab Manual Mechanics-II
15/26
Experiment No: 07
To determine Moment of Inertia of fly wheel by free falling method.
Apparatus:
Fly wheel apparatus, thread, weight, stop watch.
Theory:
A fly wheel is rotating mechanical device that is used to store rotational energy.
The Andalusion agronomist Ibn Bassal in 1060 in his Kitabal-Filaha, describes the
flywheel effect employed in a water wheel machine.
15
8/2/2019 Lab Manual Mechanics-II
16/26
Application of fly wheel is: Reciprocating engines, friction motors, punching and riveting
machines, aircraft fuel system.
Moment of Inertia: also called mass moment of Inertia, rotational inertia, polar moment
of inertia or the angular mass is a measure of an object resistance to changes to its
rotation. It is the property of the material.
M.O.I = mr2
It is different for different shapes of bodies. E.g for ball it is 2/5mr2. However for fly
wheel M.O.I = mght2/8^2N(N+n) where
M= mass
N= no of revolutions due to mass m
n= no of turns of thread.
T= total time of revolutions.
H= height
Procedure:
1. Wound a thread aver the flywheel also count number of turns also attach ahanger on the end side of the thread.
2. Put some weight on the hanger.3. Now release the weight and on the same instant start the stop watch.
4. Count the number of revolutions until flywheel stops, when the fly wheel stops atthe same instant stop the stopwatch and note the time t.
5. Calculate the moment of inertia by the formula.Precautions:
1. Turns of the thread should not overlap each other and they should be tight.2. Marking the center of flywheel can help counting number of revolutions.3. Take care while starting or stopping the stop watch.
16
8/2/2019 Lab Manual Mechanics-II
17/26
Experiment No: 08
To verify the relationship between angular and linear velocity
Apparatus
An axle mounted in bearings
Three differential diameters around a light cord is wrapped and a free and
carries a small mass
The axle also carriers a hand wheel at one end which has stop pin so that
exact number of revolutions can be held
Procedure
17
8/2/2019 Lab Manual Mechanics-II
18/26
If necessary remove the stop pin and wind the masses up so that all are
ear the axle, the replace the stoppin.it is convenient to have all the
masses level to start.the masses can be adjusted by screwing on their
indvidual adjuster. Measure the height of masses above the floor.
Remove the stop pin and under allow the shaft number of times, say five.
Then replace the stop pin. Again measure the respective axle diameters
and note your data in a suitable table.
Results
Fill in the table below with your experimental data and compute the
remaining values
Axle diameter
Intial height h1
final height h2
S=h1-h2
S/d
30mm 50mm 70mm
W=2s/rat
As the axle is rigid w and t are the same for all three diameters during themotion. Hence we may write
S1/r1=s2/r2=s3/r3
Comments
This experiment was very good
It is easy to perform
Precaution
Value should be taken accurately
Height should be taken accurately
18
8/2/2019 Lab Manual Mechanics-II
19/26
Masses should be taken accurately
19
8/2/2019 Lab Manual Mechanics-II
20/26
Experiment No: 09
i. To find tension in jib and tie of derrick crane
ii. To compare experimental and graphical value:
Theory
Tension: process of stretching something tight.
Jib: The arm of a mechanical crane
Tie :
A beam or rod that joins parts and gives support.
Derrick crane: A machine for hoisting and moving heavy objects,
consisting of a movable boom equipped with cables and pulleys and
connected to the base of an upright stationary beam.
Procedure
20
8/2/2019 Lab Manual Mechanics-II
21/26
Setup the apparatus as describe above. Adjust collar as required and
ensure that the forked of the jib is screwed well into the sleeve to allow for
adjustment after loading. Selecting suitable dimensions for the jib, the
height of the collar and carefully note the dimensions a, back and d show
in the sketch below. The hanger should not be fitted at this stage
Note the initial readings of the tie and jib laces. Suspend a suitable load
from the hook. Adjust the length of the tie by altering the cord and adjust
the length of the jib by revolving the jib sleeves until the original dimension
of the configuration are re-established. Now note the final readings of jib
and tie laces. Repeat the experiment for different loads.
Change the shape of the configuration an
D repeats the above experiments.
Result
Tabulate the results as follows
Dimensions Applied load
p(N)
Jib force J Tie force T
a b c d initial
final net initial
final Net
21
8/2/2019 Lab Manual Mechanics-II
22/26
Experiment No: 10
To find the velocity ratio, mechanical advantage and load lost in friction and the
efficiency of worm and worm wheel.
Apparatus:
1. Worm
2. Worm wheel
3. Weight
Theory :
A worm drive is a gear arrangement in which a worm (which is a gear inthe form of a screw) meshes with a worm gear (which is similar in
appearance to a spur gear, and is also called a worm wheel). The
terminology is often confused by imprecise use of the term worm gear to
refer to the worm, the worm gear, or the worm drive as a unit.
Like other gear arrangements, a worm drive can reduce rotational
speed or allow higher torque to be transmitted. The image shows a
section of a gear box with a worm gear being driven by a worm. A worm is
an example of a screw, one of the six simple machines.
22
8/2/2019 Lab Manual Mechanics-II
23/26
Procedure:
1. For one complete turn of pulley a wheel effort p is applied the worm moves the
worm wheel through teeth and for one complete turn of worm wheel the load wraises through a height equal to circumference of pulley hence velocity ratio.
2. V=dist moved by effort/dist moved by load.
3. Now find p which is just to raise the load w attached to worm wheel.
4. Do it for w=0, 4, 6, 8., mechanical advantage is given as
5. M .A=w/p, Efficiency=w/pv*100.
6. Calculate these for each reading. If the machine were ideal, the load L lifted by it
would satisfy the relation.
7. P* dist moved by effort=L*dist moved by load is L=pv.
8. Hence L-w or pv-w is called load lost due to friction.
s/no Load w(lds)
Effort p M.A=w/p % Efficiency=w/pv*100
Load lost lfriction=pv-w
Precautions:
1. Take care that effort is applied is such a way that loads are raised not allowed.
2. That value of effort p is to be considered just enough to raise the loads.
23
8/2/2019 Lab Manual Mechanics-II
24/26
Experiment: 11
To find the velocity ratio, mechanical advantage and the load lost in friction and
the efficiencies of a western differential pulley.
Apparatus:
1. Western differential pulley
2. Lock
3. Weights
Theory :
A differential pulley, sometimes called a "chain hoist," or sometimes
colloquially called a "chain fall," is used to manually lift very heavy objects
like car engines. It is operated by pulling upon the slack section of a
continuous chain that wraps around pulleys. The relative sizes of two top
pulleys determine the maximum weight that can be lifted by hand.
24
8/2/2019 Lab Manual Mechanics-II
25/26
25
8/2/2019 Lab Manual Mechanics-II
26/26
Procedure:
1. For one complete turn off pulley at where effort p is applied, the worm moves the
worm wheel through teeth and for one complete turn of worm wheel the load wraises through a height equal to circumference of pulley.
2. Hence velocity ratio: V=dist moved by effort/dist moved by load.
3. Now find p which is just to raise the load w attached to worm wheel.
4. Do it for w=0, 4, 6, 8
5. Mechanical advantage is given as M.A=w/p. Efficiency=w/pv*100.
6. Calculate these for each reading. If the machine were ideal, the load l lifted by it
would satisfy the relation.
7. P*dist moved by effort=L*dist moved load is L=pv
8. Hence L-w or pv-w is called load lost due to friction.
9. Take w along x-axis and all other quantities along y-axis.
10.Velocity ratio=v=8x/1/2x=16
S.NO Load w(lbs)
Effort p(lbs)
Mechanicaladvantage=w/p
Efficiency=w/pv*100
Load lost infriction=pv-w
Precautions:
1. Take care that effort is applied in such a way that load is raised not Lowered.
2. That value of effort p is to be considered just enough to raise the loads.
26