Post on 10-Aug-2021
transcript
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
Permanent Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance (1 kHz) 1 nF to 100 nF 0.056% to 0.061% Direct Method usingLCR Meter
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance (1 kHz) 100 nF to 1 µF 0.05% Direct Method usingLCR Meter
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance (1kHz) 1 µF to 100 µF 0.05% Direct Method usingLCR Meter
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (300 Hz to 10kHz)
1 A to 20 A 0.079% to 0.102% Direct Method withusing master 8½ DMMFluke 8508 A
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (300 Hz to 10kHz)
100 µA to 100 mA 0.03% Direct Method usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 1 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (300 Hz to 10kHz)
100 mA to 1 A 0.041% to 0.079% Direct Method usingmaster 8½ DMM Fluke8508 A
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (50 Hz) 20 A to 1000 A 0.5% to 1.0% Direct method masterUsing Shunt With DMM
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Inductance (1kHz) 100 µH to 100 mH 0.236% to 0.065% Direct Method usingmaster LCR meter
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Inductance (1kHz) 100 mH to 10 H 0.065% to 0.073% Direct Method usingLCR Meter
10 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (20 Hz to 50kHz)
1 mV to 100 mV 0.820% to 0.014% Direct method usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 2 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
11 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (20 Hz to 50kHz)
1 V to 100 V 0.017% to 0.011% Direct Method usingmaster 8½ DMM Fluke8508A
12 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (20 Hz to 50kHz)
100 mV to 1 V 0.014% to 0.017% Direct method usingmaster 8½ DMM Fluke8508A
13 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (45 Hz to 1kHz)
100 V to 1000 V 0.01% to 0.007% Direct Method usingmaster 8½ DMM Fluke8508 A
14 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (50 kHz to 500kHz)
1 V to 20 V 0.07% to 0.230% Direct Method usingmaster 8½ DMM Fluke8508 A
15 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Capacitance (1 kHz) 220 pF to 300 nF 5.79% to 0.27% Direct Method usingmaster StandardCalibrator Fluke 5522A& Decade CapacitanceBox
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 3 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
16 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Capacitance (100 Hz) 1 µF to 30 µF 1.55% to 0.56% Direct Method usingmaster StandardCalibrator Fluke 5522A& Decade CapacitanceBox
17 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Capacitance(1 kHz) 300 nF to 100 µF 0.27% to 1.13% Direct Method usingmaster StandardCalibrator Fluke 5522A& Decade CapacitanceBox
18 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1 kHz) 3.3 mA to 1 A 0.15% to 0.073% Direct Method by usingmaster StandardCalibrator Fluke 5522A
19 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1 kHz) 30 µA to 330 µA 0.54% to 0.17% Direct Method by usingmaster StandardCalibrator Fluke 5522A
20 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1 kHz) 330 µA to 3.3 mA 0.17% to 0.15% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 4 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
21 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (10Hz to 1kHz) 330 µA to 3.3 mA 0.25% to 0.26% Direct Method by usingmaster StandardCalibrator Fluke 5522A
22 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (10Hz to 1kHz) 3.3 mA to 3 A 0.26% to 0.23% Direct Method by usingmaster StandardCalibrator Fluke 5522A
23 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1kHz) 1 A to 10 A 0.073% to 0.12% Direct Method by usingmaster StandardCalibrator Fluke 5522A
24 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (45 Hz to 5kHz)
3 A to 20 A 0.23% to 0.13% Direct Method by usingmaster StandardCalibrator Fluke 5522A
25 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (50 Hz) 20 A to 1000 A 0.68% to 0.37% Direct Method by usingmaster StandardCalibrator Fluke 5522A& current coil
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 5 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
26 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Inductance (1 kHz) 100 µH to 10 H 2.35 % to 1.14 % Direct Method usingmaster DecadeInductance Box
27 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50 Hz @ UPF 1.2 W to4.8 kW,0.01 A to 20A,120 V to 240 V
0.16% Direct Method usingmaster StandardCalibrator Fluke 5522A
28 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50Hz @ 0.5 Lag, 6 W
to 2.4 kW,0.01 A to20 A,120 V to240 V
0.46% Direct Method usingmaster StandardCalibrator Fluke 5522A
29 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50Hz @ 0.8 Lead 9.6W to 3.8 kW,0.01 A to20 A,120 V to 240 V
0.20% Direct Method usingmaster StandardCalibrator Fluke 5522A
30 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50Hz @0.2 Lag, 2.4 W
to 960 W,0.01 A to20 A,120 V to240 V
0.56% Direct Method usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 6 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
31 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power Factor 0.2 Lag to UPF 0.003 Direct Method usingmaster StandardCalibrator Fluke 5522A
32 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power Factor 0.2 Lead to UPF 0.0003 Direct Method usingmaster StandardCalibrator Fluke 5522A
33 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (10 Hz to 10kHz)
1 V to 30 V 0.080% to 0.042% Direct Method by usingmaster StandardCalibrator Fluke 5522A
34 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (10 Hz to 10kHz)
100 mV to 1 V 0.086% to 0.080% Direct Method by usingmaster StandardCalibrator Fluke 5522A
35 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (10 Hz to 10kHz)
30 mV to 100 mV 0.12% to 0.086% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 7 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
36 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (100kHz) 30 mV to 30 V 0.452% to 0.054% Direct Method by usingmaster StandardCalibrator Fluke 5522A
37 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (100kHz) 30 V to 100 V 0.054% to 0.024% Direct Method by usingmaster StandardCalibrator Fluke 5522A
38 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45 Hz to 1kHz)
30 V to 300 V 0.20% to 0.022% Direct Method by usingmaster StandardCalibrator Fluke 5522A
39 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45 Hz to 1kHz)
300 V to 1000 V 0.022% to 0.035% Direct Method by usingmaster StandardCalibrator Fluke 5522A
40 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (450kHz) 30 mV to 3 V 1.116% to 0.121% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 8 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
41 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45Hz to10kHz)
1 mV to 3 mV 0.712% to 0.24% Direct Method by usingmaster StandardCalibrator Fluke 5522A
42 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45Hz to10kHz)
3 mV to 30 mV 0.24% to 0.042% Direct Method by usingmaster StandardCalibrator Fluke 5522A
43 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 1 A to 20 A 0.080% to 0.052% Direct method by usingmaster 8½ DMM Fluke8508 A
44 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 1 mA to 100 mA 0.002% to 0.008% Direct method by usingmaster 8½ DMM Fluke8508 A
45 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 10 µA to 100 µA 0.0010% Direct method by usingmaster 8½ DMM Fluke8508 A
46 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 100 µA to 1 mA 0.001% to 0.002% Direct method by usingmaster 8½ DMM Fluke8508 A
47 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 100 mA to 1 A 0.062% to 0.080% Direct method by usingmaster 8½ DMM Fluke8508 A
48 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 20 A to 1000 A 1.19% Direct Method using8½ DMM Fluke 8508with Shunt
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 9 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
49 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 Gohm to 10 Gohm 0.116% to 0.133% Direct Method by Usingmaster 8½ DMM Fluke8508 A
50 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 Mohm to 10 Mohm 0.001% to 0.002% Direct Method by Usingmaster 8½ DMM Fluke8508 A
51 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 mohm to 100 mohm 0.061% to 0.207% Direct Method by Usingmaster LCR Meter &DRB
52 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 ohm to 100 ohm 0.0015% to 0.0010% Using LCR Meter &DRB
53 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 10 kohm to 100 kohm 0.0007% to 0.0008% Direct Method by Usingmaster 8½ DMM Fluke8508 A
54 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 10 Mohm to 100 Mohm 0.002% to 0.008% Direct method by usingmaster 8½ DMM Fluke8508 A
55 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 Mohm to 1 Gohm 0.008% to 0.116% Direct Method by Usingmaster 8½ DMM Fluke8508 A
56 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 mohm to 150mohm
0.206% Direct Method by Usingmaster LCR Meter &DRB
57 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 ohm to 10 kohm 0.0010% to 0.0007% Direct Method by Usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 10 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
58 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 kohm to 1 Mohm 0.0008% to 0.001% Direct Method by Usingmaster 8½ DMM Fluke8508 A
59 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 150 mohm to 1 ohm 0.206% to 0.0015% Direct Method by usingmaste LCR Meter &DRB
60 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 1 mV to 100 mV 0.44% to 0.0003% Direct Method by usingmaster StandardCalibrator Fluke 5522A
61 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 1 V to 100 V 0.0002% to 0.0003% Direct Method by usingmaster DMM Fluke8508A
62 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 100 mV to 1 V 0.0003% to 0.0003% Direct Method by usingmaster StandardCalibrator Fluke 5522A
63 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 100 V to 1000 V 0.0004% to 0.0004% Direct Method by usingmaster StandardCalibrator Fluke 5522A
64 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 1 A to 10 A 0.027% to 0.063% Direct Method by usingmaster StandardCalibrator Fluke 5522A
65 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 1 mA to 100 mA 0.016% to 0.011% Direct Method by usingmaster StandardCalibrator Fluke 5522A
66 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 10 µA to 100 µA 0.25% to 0.023% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 11 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
67 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 10 A to 20 A 0.063% to 0.11% Direct Method by usingmaster StandardCalibrator Fluke 5522A
68 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 100 µA to 1 mA 0.023% to 0.016% Direct Method by usingmaster StandardCalibrator Fluke 5522A
69 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 100 mA to 1 A 0.011% to 0.027% Direct Method by usingmaster StandardCalibrator Fluke 5522A
70 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 20 A to 200 A 0.5% Direct Method usingCurrent Source
71 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 200 A to 1000 A 0.66% to 0.32% Direct Method by usingmaster Fluke 5522Awith current coil 5500A
72 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Power 10 W to 1 kW,1V to1000V, 1mA to 1000A.
0.08% to 0.45% Using Calibrator Fluke5522A with CurrentCoil Direct Method.
73 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Power (1V to1000V, 1mA to 1000A)
1 KW to 19.9 KW 0.45% to 0.65% Using Calibrator Fluke5522A with current coilDirect Method.
74 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Oscilloscope 1 mV to 130 V 0.29% to 0.096% Direct Method
75 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 0.1 Mohm to 1 Gohm 5.89% to 4.91% Direct Method usingmaster of high stabilityDecade Megohm Box
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 12 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
76 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 Gohm to 100 Gohm 4.91% to 8.61% Direct Method usingmaster of high stabilityDecade Megohm Box
77 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 kohm to 10 kohm 0.0036% to 0.0035% Direct Method usingStandard CalibratorFluke 5522A
78 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 mohm 0.609% Direct Method usingfixed resistor box
79 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 Mohm to 10 Mohm 0.0041% to 0.014% Direct Method usingStandard CalibratorFluke 5522A
80 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 ohm to 10 ohm 0.10% to 0.015% Direct Method usingStandard CalibratorFluke 5522A
81 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 kohm to 100 kohm 0.0035% to 0.0034% Direct Method usingStandard CalibratorFluke 5522A
82 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 mohm 0.610% Direct Method usingfixed resistor box
83 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 Mohm to 300 Mohm 0.014% to 0.38% Direct Method usingStandard CalibratorFluke 5522A
84 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 ohm to 100 ohm 0.015% to 0.004% Direct Method usingStandard CalibratorFluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 13 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
85 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 Gohm to 1 Tohm 5.81% Direct Method usingmaster of high stabilityDecade Megohm Box
86 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 ohm to 1 kohm 0.004% to 0.0036% Direct Method usingStandard CalibratorFluke 5522A
87 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 kohm to 1 Mohm 0.0034% to 0.0041% Direct Method usingStandard CalibratorFluke 5522A
88 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 150 mohm 0.609% Direct Method usingfixed resistor box
89 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 150 mohm to 1 ohm 0.611% to 0.10% Direct Method usingStandard CalibratorFluke 5522A:
90 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 300 Mohm to 1 Gohm 0.38% to 1.78% Direct Method usingStandard CalibratorFluke 5522A
91 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 50 mohm 0.610% Direct Method usingsing fixed resistor box
92 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 1 mV to 10 mV 0.240% to 0.023% Direct Method by usingmaster StandardCalibrator Fluke 5522A
93 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 1 V to 10 V 0.0015% to 0.0016% Direct Method usingmaster StandardCalibrator Fluke 5522A:
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 14 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
94 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 10 mV to 100 mV 0.023% to 0.0039% Direct Method by usingmaster StandardCalibrator Fluke 5522A
95 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 10 V to 1000 V 0.0016% to 0.0023% Direct Method by usingmaster StandardCalibrator Fluke 5522A
96 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 100 mV to 1 V 0.0039% to 0.0015% Direct Method by usingmaster StandardCalibrator Fluke 5522A
97 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Amplitude-Sq wave /Oscilloscope (1 kHz)
1 mV to 55 Vp-p 0.6% to 0.3% Direct Method by usingmaster StandardCalibrator Fluke 5522A
98 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Bandwidth -Oscilloscope
50 kHz to 1 GHz 0.23% to 0.87% Direct Method usingmaster StandardCalibrator Fluke 5522A
99 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(B type)
600 °C to 1750 °C
0.53°C to 0.39°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
100 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(E type)
-200 °C to 900 °C 0.48°C to 0.27°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 15 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
101 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller (Jtype)
-200 °C to 1200 °C 0.28°C to 0.31°C Direct Method by usingMaster used- StndCalibrator Fluke 5522A& 6½ DMM
102 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(K type)
-200 °C to 1350 °C 0.26°C to 0.48°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
103 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(N type)
-200 °C to 1300 °C 0.48°C to 0.35°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
104 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(R type)
10 °C to 1750 °C 0.67°C to 0.48°C Direct Method by usingMaster StandardCalibrator fluke 5522A
105 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(RTD type)
-200 °C to 800 °C 0.05 °C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 16 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
106 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(S type)
10 °C to 1450 °C 0.56°C to 0.54°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
107 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller (Ttype)
-200 °C to 400 °C 0.60°C to 0.17°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
108 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(B type)
600 °C to 1750 °C 0.47°C to 0.11°C Direct Method by usingMaster StandardCalibrator fluke 5522A
109 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(E type)
-200 °C to 900 °C 0.20°C to 0.45°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
110 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller (Jtype)
-200 °C to 1200 °C 0.15°C to 0.25°C Direct Method by usingMaster StandardCalibrator fluke 5522A
111 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(K type)
-200 °C to 1350 °C 0.37°C to 0.48°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 17 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
112 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(N Type )
-200 °C to 1300 °C 0.45°C to 0.30°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
113 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(R type)
10 °C to 1750 °C 0.62°C to 0.44°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
114 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(RTD type)
-200 °C to 800 °C 0.071°C to 0.083°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
115 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(S type)
10 °C to 1750 °C 0.61°C to 0.51°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
116 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller (Ttype)
-200 °C to 400 °C 0.55°C to 0.16°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
117 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 GHz 0.0011% to 0.0024% Direct Method usingmaster FrequencyCounter Philips- PM6669
118 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Timer 1 sec to 9000 sec 0.06% to 0.05% Comparison Method byusing master DigitalTimer Beltronics - 501
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 18 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
119 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 1 Hz to 1 GHz 0.004% to 0.006% Direct Method usingmaster StandardCalibrator Fluke 5522A
120 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Timer Marker /Oscilloscope
1 ns to 5 s 0.0003 sec Direct Method usingmaster StandardCalibrator Fluke 5522A
121 MECHANICAL-ACCELERATION ANDSPEED
Acceleration (Peak)@80Hz
6.6 m/s2 2.96% Using Digital VibrationMeter by ComparisonMethod
122 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@160Hz
10.0 m/s2 2.83% Using Digital VibrationMeter by ComparisonMethod
123 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@160Hz
20.1 m/s2 2.48 % Using Digital VibrationMeter by ComparisonMethod
124 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@160Hz
40.2 m/s2 2.44 % Using Digital VibrationMeter by ComparisonMethod
125 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@160Hz
50.1 m/s2 2.41 % Using Digital VibrationMeter by ComparisonMethod
126 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@40Hz
12.3 m/s2 2.56 % Using Digital VibrationMeter by ComparisonMethod
127 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@40Hz
20.5 m/s2 2.49 % Using Digital VibrationMeter by ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 19 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
128 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@40Hz
28.8 m/s2 2.49 % Using Digital VibrationMeter by ComparisonMethod
129 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@40Hz
4.0 m/s2 3.43 % Using Digital vibrationMeter By ComparisonMethod
130 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@80Hz
11.5 m/s2 2.63 % Using Digital VibrationMeter by ComparisonMethod
131 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@80Hz
16.7 m/s2 2.53 % Using Digital VibrationMeter by ComparisonMethod
132 MECHANICAL-ACCELERATION ANDSPEED
Acceleration(Peak)@80Hz
2.8 m/s2 5.04 % Using Digital VibrationMeter by ComparisonMethod
133 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@160Hz
0.009 mm 11.87% Using Digital VibrationMeter by ComparisonMethod
134 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@160Hz
0.030 mm 4.36% Using Digital VibrationMeter by ComparisonMethod
135 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@160Hz
0.050 mm 3.24% Using Digital VibrationMeter by ComparisonMethod
136 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@160Hz
0.126 mm 2.56% Using Digital VibrationMeter by ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 20 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
137 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@40Hz
0.065 mm 2.89% Using Digital VibrationMeter by ComparisonMethod
138 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@40Hz
0.196 mm 2.47% Using Digital VibrationMeter by ComparisonMethod
139 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@40Hz
0.263 mm 2.45% Using Digital VibrationMeter by ComparisonMethod
140 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@40Hz
0.459 mm 2.44% Using Digital VibrationMeter by ComparisonMethod
141 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@80 Hz
0.026 mm 4.79% Using Digital VibrationMeter by ComparisonMethod
142 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@80Hz
0.011 mm 10.27% Using Digital VibrationMeter by ComparisonMethod
143 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@80Hz
0.046 mm 3.08% Using Digital VibrationMeter by ComparisonMethod
144 MECHANICAL-ACCELERATION ANDSPEED
Displacement(Peak)@80Hz
0.067 mm 2.76% Using Digital VibrationMeter by ComparisonMethod
145 MECHANICAL-ACCELERATION ANDSPEED
Stroboscope,tachometer (NonContact Type)
25000 rpm to 45000rpm
0.008% By Comparison methodby using masterTachometer Calibrator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 21 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
146 MECHANICAL-ACCELERATION ANDSPEED
Stroboscope,tachometer (NonContact Type)
60 rpm to 25000 rpm 0.7% to 0.008% By Comparison methodby using masterTachometer Calibrator
147 MECHANICAL-ACCELERATION ANDSPEED
Tachometer ( ContactType)
100 rpm to 5000 rpm 1.4% to 0.12% Comparison Method byusing masterTachometer Calibration
148 MECHANICAL-ACCELERATION ANDSPEED
Velocity (Peak) @40Hz 82.0 mm/s 2.42% Using Digital VibrationMeter by ComparisonMethod
149 MECHANICAL-ACCELERATION ANDSPEED
Velocity (Peak)mm/s@40Hz
16.1 mm/s 2.52% Using Digital VibrationMeter by ComparisonMethod
150 MECHANICAL-ACCELERATION ANDSPEED
Velocity (Peak)@40Hz 48.7 mm/s 2.43% Using Digital VibrationMeter by ComparisonMethod
151 MECHANICAL-ACCELERATION ANDSPEED
Velocity (Peak)@40Hz 65.1 mm/s 2.42% Using Digital VibrationMeter by ComparisonMethod
152 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@160Hz 39.9 mm/s 2.42% Using Digital VibrationMeter by ComparisonMethod
153 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@160Hz 69.7 mm/s 2.41% Using Digital VibrationMeter by ComparisonMethod
154 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@160Hz 9.9 mm/s 2.80% Using Digital VibrationMeter by ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 22 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
155 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@160Hz 99.3 mm/s 2.41% Using Digital VibrationMeter by ComparisonMethod
156 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@80Hz 13.2 mm/s 2.50% Using Digital VibrationMeter by ComparisonMethod
157 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@80Hz 22.8 mm/s 2.47% Using Digital VibrationMeter by ComparisonMethod
158 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@80Hz 33.3 mm/s 2.44% Using Digital VibrationMeter by ComparisonMethod
159 MECHANICAL-ACCELERATION ANDSPEED
Velocity(Peak)@80Hz 5.7 mm/s 3.00% Using Digital VibrationMeter by ComparisonMethod
160 MECHANICAL-ACOUSTICS
Sound Level Meter 114 dB @ 1kHz 0.82dB Using Sound levelCalibrator
161 MECHANICAL-ACOUSTICS
Sound Level Meter 94 dB @ 1kHz 0.82dB Using Sound levelCalibrator
162 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
3 Point Micrometer,Res : 0.001 mm
0 to 100 mm 3.6µm Using master MasterRing Gauges
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 23 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
163 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Bevel Protractor, Res:1min
0 ° to 360 °
5.66arc of min Using profile projector
164 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Bore Gauge (0.001mm) Upto 2mmTransmisson only
2.4µm Using masterElectronic Dial gaugecalibration Tester
165 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper (Analog / Dial /Digital) Res: 0.01mm
0 mm to 1000 mm 8.6µm Using master CaliperChecker & GaugeBlock
166 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper Checker 0 mm to 1000 mm 8µm Using master GaugeBlock Set & HeightMeasuring System
167 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Coating ThicknessGauge (Res: 0.1 µm)
0 to 2000 µm 3.4µm Using master StandardThickness Foils
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 24 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
168 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Combination Set,Res:1°
0 ° to 180 ° 13.2 arc of min Using Profile Projector
169 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Comparator Dial Stand( Flatness)
Up to 300 mm 7µm Using master Lever dial& Linear height master
170 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Micrometer,Res: 0.001mm
0 mm to 300 mm 4µm Using Master GaugeBlock Set
171 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Vernier ( Analog/ Dial / Digital), Res:0.01mm
0 mm to 600 mm 15.2µm Using master Gaugeblock Set
172 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Calibration Tester /LVDT probe withIndicator, Res:0.001µm
0 to 25mm 1.3µm Using master ULM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 25 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
173 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Gauge- Plungertype ( Analog / Digital),Res: 0.001mm
0 mm to 1 mm 2.3µm Using masterElectronic Dial GaugeCalibration Tester
174 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Gauge- Plungertype ( Analog / Digital),Res: 0.001mm
0 mm to 10 mm 2.6µm Using masterElectronic Dial gaugeCalibration Tester
175 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Gauge- Plungertype ( Analog / Digital),Res: 0.001mm
0 mm to 50 mm 6.3µm Using masterElectronic DialCalibration GaugeTester
176 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Thickness Gauge,Res: 0.01 mm
Upto 10mm 7µm Using master GaugeBlock Set
177 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Elongation gauge 14.7 mm to 81 mm 24µm Using Digital Caliper byComparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 26 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
178 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Engineering Square /Angle Plates(Squareness)
Up to 350 mm 7.0µm Using master DigitalDial Gauge & LinearHeight Master
179 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog / Digital /Flange / Point / V Anvil/ Pitch ) , Res : 0.001mm
0 mm to 450 mm 3µm Using master GaugeBlock Set
180 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog / Digital /Flange / Point / V Anvil/ Pitch ) , Res : 0.01mm
0 mm to 1000 mm 7µm Using master GaugeBlock Set
181 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Feeler gauge 0.02 mm to 1 mm 2.1µm Using master UniversalLength Machine
182 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Flankiness Gauge 4.89 mm to 33.9 mm 7µm Using Profile ProjectorBy Comparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 27 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
183 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Foils Upto 2000 µm 1.2µm Using master UniversalLength Machine
184 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Gauge Block Set 0.5 mm to 25 mm 0.12 µm Using master GaugeBlock Grade 'k'comparator system
185 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Gauge Block Set 25 mm to 50 mm 0.12µm Using master GaugeBlock Grade 'k'
186 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Gauge Block Set 50 mm to 75 mm 0.14µm Using master GaugeBlock Grade 'k'
187 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Gauge Block Set 75 mm to 100 mm 0.20µm Using master GaugeBlock Grade 'k'
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 28 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
188 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Granite Square(Squareness, Flatness)
Upto 600 mm 13.5µm Using Lever DialGauge and Linearheight Master
189 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Groove Dial / LegCaliper (OD & ID)Gauge, Res: 0.025mm
Upto 150 mm 7.0µm Using master GaugeBlock Set
190 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge ( Dial /Digital & Analog ) Res:0.01mm
0 mm to 1000 mm 11.8µm Using master CaliperChecker
191 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge ( Dial /Digital & Analog ) Res:0.01mm
0 mm to 600 mm 11.2µm Using master CaliperChecker
192 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height MeasuringSystem, Res: 0.1 µm
0 mm to 1000 mm 4.6µm By using Master GaugeBLock long Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 29 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
193 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Internal Micrometer /Stick Micrometer(Including ExtensionRod ) Res: 0.01mm
Upto 300 mm 8µm Using Gauge Block Set& gauge BlockAccessories
194 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Dial Gauge(0.001mm)
0 to 0.14 mm 2.4µm Using masterElectronic Dial gaugeCalibration Tester
195 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Dial Gauge(0.002mm)
0 to 0.2 mm 3.1µm Using masterElectronic Dial gaugeCalibration Tester
196 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Dial Gauge, 0.01mm
0 to 1 mm 5.3µm Using masterElectronic Dial gaugecalibration Tester
197 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Measuring Pins (Grade 1& 2)
Upto 25 mm 2µm Using Universal lengthMachine
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 30 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
198 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Measuring Tape / PiTape, Res: 0.5 mm1.00 mm lc
Upto 50000 mm (541 + L/100)µm(L inmm)
Using master Scale &Tape CalibrationMachine
199 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Micrometer Head, Res: 0.001mm
Up to 25 mm 1.3µm Using Master LeverDial Gauge & LinearHeight Master
200 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Parallel Block Up to 1000 mm 10µm Using master LeverDial Gauge
201 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Pistol Caliper (Res:0.01 mm)
0 to 100 mm 10µm Using master GaugeBlock Set
202 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Pitch Micrometer, Res :0.01mm
0 to 200 mm 7µm Using master GaugeBlock Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 31 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
203 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauges 1 mm to 300 mm 1.5µm Using master UniversalLength Machine
204 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Ring Gauges 4 mm to 300 mm 2.3µm Using master UniversalLength Machine
205 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Portable Roughnesstester Ra/ Rz
Up to 100 µm 6.41 µm Using SurfaceRoughness MasterBlock
206 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Radius Gauges 0.5 mm to 25.0 mm 6µm Using master Profileprojector
207 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Setting Rods &Extensions Rods
25 mm to 975 mm 10µm Using master GaugeBlock Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 32 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
208 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauges / DialSnap Gauges / WidthGauges
10 mm to 300 mm 2.5 µm Using Universal LengthMachine
209 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Spirit Level / FrameLevel, Res : 10µm / m
Upto 0.12 mm/m 15µm/m Using masterElectronic Level
210 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Steel scale / Taperscale Res: 0.5 / 1 mm
0 mm to 1000 mm 271µm Using master scale &Tape CalibrationMachine
211 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge 0 mm to 1000 mm 13.5µm Using Linear HeightMaster and lever DialGauge
212 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Tape Scale Calibrator 0 mm to 1000 mm 10.2µm Using Slip Gauge Setand Long Slip Gauges
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 33 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
213 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Taper Thread PlugGauge ( Effective Dia)
0 mm to 100 mm 3µm Using master UniversalLength machine
214 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Taper Thread RingGauge ( Effective Dia)
0 mm to 110 mm 4.8µm Using master UniversalLength Machine
215 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Test Sieves 0.16 mm to 1 mm 5µm Using master profileprojector
216 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Test Sieves 1 mm to 100 mm 18µm Using master profileprojector
217 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Pitch Gauge,Set Pitch Flank Angle
0.3 mm to 6.0 mm 3 µm & 5.1 arc min Using master ProfileProjector
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 34 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
218 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Pitch Gauge,Set Pitch Flank Angle
55 ° to 60 ° 5.1 min of arc Using master ProfileProjector
219 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread plug Gauge (Effective Dia)
Up to 300 mm 2.1µm Using master UniversalLength Machine
220 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Ring Gauge (Effective Dia)
3 mm to 300 mm 2µm Using master UniversalLength Machine
221 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Ultra Sonic ThicknessGauge
Upto 200mm 7.3µm Using master GaugeBlock Set
222 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Universal LengthMeasuring Machine
Upto 100 mm 0.7µm Using master GaugeBlock Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 35 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
223 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
'V' - Block (Parallelism)symmetry, squareness
Up to 200 mm 6.6µm Using master Mandrel& Lever Dial Gauge &Linear Height Master
224 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld Fillet Gauge 0 mm to 25 mm 10.1µm for linear & 3min arc
Using Profile projectorBy Comparsion Method
225 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
wet / Dry FilmApplicator
0 mm to 200 mm 8.68µm Using Profile ProjectorBy ComparisionMethod
226 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Wire gauge 0.3 mm to 10 mm 8.8 µm Using Profile ProjectorBy ComparisionMethod.
227 MECHANICAL-FORCE PROVINGINSTRUMENTS
Push Pull Gauge ,Force gauge, SpringBalance
10 N to 1000 N 1.4N Using master StainLess Weights andhanger of weights 10,50, 100 N as per VDI /VDE 2624 Part 2.1
228 MECHANICAL-HARDNESS TESTINGMACHINES
Shore Hardness Tester 0 to 100 Shore A&D 2.2 Shore A&D Using RubberHardness TesterASTM-D-2240-15
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 36 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
229 MECHANICAL-PRESSUREINDICATING DEVICES
Digital / Dial VaccumGauges / Transmitters /Transducers.
0 bar to (-) 0.75 bar 0.014 bar Digital Pressure Gaugewith uncertainty of0.0008 bar. Procedurebased on ISO 3567 &ISO 27893 standards.
230 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(HYDRAULIC)Digital /Analog PressureGauges, PressureIndicator WithTransducer /Transmitter, PressureSwitch
0 bar to 1000 bar 0.15 bar Digital Pressure gaugewith uncertainty of0.021 bar. Procedurebased on DKD-R 6-1guidelines.
231 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(HYDRAULIC)Digital /Analog PressureGauges, PressureIndicator WithTransducer /Transmitter & PressureSwitches
0 bar to 700 bar 0.29 bar Digital Pressure gaugewith uncertainty of0.182 bar. Procedurebased on DKD-R 6-1guidelines.
232 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC) Digital /Dial Gauges / PressureIndicator WithTransmitter /Transducer.
0 bar to 20 bar 0.014 bar Digital Pressure gaugewith uncertainty of0,01bar. Procedurebased on DKD-R 6-1guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 37 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
233 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC)Pressure gauges,Magnehelic gauges,Differential PressureTransmitters, LowPressure Indicators/Transducers,Barometer
0 mbar to 500 mbar 0.31 mbar Digital Manometer withuncertainty of 0.06mbar. Procedure basedon DKD-R 6-1guidelines.
234 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC)Digital /Dial Gauges / PressureIndicator WithTransmitter /Transducer.
0 bar to 70 bar 0.04 bar Digital Pressure gaugewith uncertainty of0.022 bar. Procedurebased on DKD-R 6-1guidelines.
235 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC)Pressure gauges, Magnehelicgauges, DifferentialPressure Transmitters,Low PressureIndicators/Transducers,Barometer.
0 mbar to 2000 mbar 2.14 mbar Digital Manometer withuncertainty of 1.03mbar. Procedure basedon DKD-R 6-1guidelines.
236 MECHANICAL-TORQUEMEASURINGDEVICES
Torque Wrench (Type-I)Class B,C,D,E andType II class A B C D
200 Nm to 1000 Nm 1.2 % Using Torque wrenchCalibration System asper IS/ISO 6789
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 38 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
237 MECHANICAL-TORQUEMEASURINGDEVICES
Torque Wrench (Type-I)Class B,C,D,E, TypeII, A B C D
0 Nm to 20 Nm 0.36 % Using Torque wrenchCalibration System asper IS/ISO 6789
238 MECHANICAL-TORQUEMEASURINGDEVICES
Torque Wrench (Type-I)Class B,C,D,E, TypeII, Class A, B, C, D
20 Nm to 200 Nm 1.5% Using Torque wrenchCalibration System asper IS/ISO 6789,
239 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Universal TestingMachine (CompressionMode)
100 N to 1000 KN 0.80% Using master ProvingRing and load cells asper IS 1828 Part 12015
240 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Universal TestingMachine (CompressionMode)
200 kN to 2000 KN 0.80 % Using master ProvingRing and load cells asper IS 1828 Part 12015
241 MECHANICAL- UTM,TENSION CREEPAND TORSIONTESTING MACHINE
Universal TestingMachine (TensileMode)
0.5 KN to 50 KN 0.99% Using master LoadCells as per IS 1828Part 1 2015
242 MECHANICAL-VOLUME
DENSITYHydrometer ,L.C= 0.0005 g/ ml
0.600 g / ml to 1.8 g/ ml 0.0009 g/ml using referencehydrometer andcalibration liquid ofappropriate density.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 39 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
243 MECHANICAL-VOLUME
Measuring Cylinder 10 ml 0.8 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
244 MECHANICAL-VOLUME
Measuring Cylinder 100 ml 1.9 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.001 g)
245 MECHANICAL-VOLUME
Measuring Cylinder 1000 ml 11.5 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.001g)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 40 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
246 MECHANICAL-VOLUME
Measuring Cylinder 10000 ml 75.0 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 g)
247 MECHANICAL-VOLUME
Measuring Cylinder 20 ml 1.5 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
248 MECHANICAL-VOLUME
Measuring Cylinder 200 ml 2.3 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.001 g)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 41 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
249 MECHANICAL-VOLUME
Measuring Cylinder 2000 ml 12.0 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01g)
250 MECHANICAL-VOLUME
Measuring Cylinder 5 ml 0.1 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
251 MECHANICAL-VOLUME
Measuring Cylinder 50 ml 1.5 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 42 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
252 MECHANICAL-VOLUME
Measuring Cylinder 500 ml 10.5 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodbased on ISO4787:2010 & ISO20461 with Electronicweighing Balance (Readability : 1 mg)
253 MECHANICAL-VOLUME
Measuring Cylinder 5000 ml 25.0 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 g)
254 MECHANICAL-VOLUME
Micropipette 1 µl 0.01 µl Using Weights ofAccuracy Class E1 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 43 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
255 MECHANICAL-VOLUME
Micropipette 10 µl 0.03 µl Using Weights ofAccuracy Class E1 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
256 MECHANICAL-VOLUME
Micropipette 100 µl 0.62 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
257 MECHANICAL-VOLUME
Micropipette 1000 µl 6.20 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.01 mg )
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 44 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
258 MECHANICAL-VOLUME
Micropipette 2 µl 0.01µl Using Weights ofAccuracy Class E1 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
259 MECHANICAL-VOLUME
Micropipette 20 µl 0.04 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.01 mg /0.1 mg)
260 MECHANICAL-VOLUME
Micropipette 200 µl 1.30 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 45 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
261 MECHANICAL-VOLUME
Micropipette 2000 µl 12.5 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.01 mg /0.1 mg)
262 MECHANICAL-VOLUME
Micropipette 5 µl 0.02 µl Using Weights ofAccuracy Class E1 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
263 MECHANICAL-VOLUME
Micropipette 50 µl 0.20 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.001 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 46 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
264 MECHANICAL-VOLUME
Micropipette 500 µl 3.10 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.01 mg )
265 MECHANICAL-VOLUME
Micropipette 5000 µl 32.0 µl Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 8655( part 6):2002 with using masterMicro Balance (Readability : 0.1 mg)
266 MECHANICAL-VOLUME
Pipette & burette 10 ml 0.03 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 47 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
267 MECHANICAL-VOLUME
Pipette & burette 100 ml 0.21 mlml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
268 MECHANICAL-VOLUME
Pipette & burette 25 ml 0.06ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 mg )
269 MECHANICAL-VOLUME
Pipette & burette 5 ml 0.02 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 48 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
270 MECHANICAL-VOLUME
Pipette & burette 50 ml 0.11 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
271 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
10 ml 0.03ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 mg)
272 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
100 ml 0.21 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 49 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
273 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
1000 ml 2.2 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 g)
274 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
20 ml 0.06 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 mg)
275 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
200 ml 0.41 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.001 g)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 50 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
276 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
2000 ml 4.60 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 g)
277 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
5 ml 0.02 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.01 mg )
278 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
50 ml 0.11 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.1 mg )
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 51 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
279 MECHANICAL-VOLUME
Volumetric ( Flask /Beaker)
500 ml 1.03 ml Using Weights ofAccuracy Class E2 &Distilled water byGravimetric methodson ISO 4787:2010 &ISO 20461 with masterusing Balance (Readability : 0.001 g)
280 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I) Readability :0.0001 mg
1 mg to 2.1 g 0.003mg Using StandardWeights of acccuracyClass E1 andprocedure based OIMLR-76: 2006.
281 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class Ii) Readability :1 mg
1 mg to 1 kg 0.002 g Using StandardWeights of accuracyClass E1 & E2, andprocedure as per OIMLR-76: 2006.
282 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :100 mg
0.1 g to 20 kg 0.10 g Using StandardWeights of AccuracyClass E2 & F1.Procedure as per OIMLR-76: 2006.
283 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III)Readability :10 g
10 g to 100 kg 10.0 g Using StandardWeights of accuracyClass M1 andprocedure as per OIMLR76:2006
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 52 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
284 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCEReadability : 1 g
1 g to 100 kg 1.0 g Using StandardWeights of accuracyClass M1, andprocedure as per OIMLR76:2006.
285 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I) Readability :0.001 mg
1 mg to 5.1 g 0.005 mg Using StandardWeights of accuracyClass E1 andprocedure as per OIMLR-76: 2006.
286 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I) Readability :0.1 mg
1 mg to 200 g 0.06 mg Using StandardWeights of accuracyClass E1 andprocedure as per OIMLR-76: 2006.
287 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I)Readability :0.01 mg
1 mg to 50 g 0.011 mg Using StandardWeights of accuracyClass E1 andprocedure as per OIMLR-76: 2006.
288 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class II)Rwadability:10 mg
0.1 mg to 5 kg 0.011 g Using StandardWeights of AccuracyClass E1& E2 .Procedure as per OIMLR 76:2006.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 53 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
289 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :100 mg
0.1 g to 35 kg 0.97 g Using StandardWeights of accuracyClass F1& M1.Peocedure as perOIML R-76: 2006.
290 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :100 mg
0.1 mg to 10 kg 0.037 g Using StandardWeights of AccuracyClass E1& E2.Procedure as per OIMLR-76: 2006.
291 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :50 g
2 kg to 500 kg 20.0 g Using StandardWeights of accuracyClass F2. Peocedureas per OIML R76:2006
292 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance (ClassIII)Readability: 100 mg
0.1 mg to 2 kg 0.011 mg Using Weights ofAccuracy Class E1&E2 . Procedure as perOIML R 76:2006.
293 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class IV)Readability :100 g
2 kg to 1000 kg 50.0 g Using StandardWeights of accuracyClass M1, procedureas per OIML R76:2006
294 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
1 g 0.004 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 54 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
295 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
1 mg 0.002 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance (d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
296 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
10 g 0.012mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.01mg).Procedure as per OIMLR 111-1 guidelines.
297 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
10 mg 0.002 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
298 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
2 g 0.004 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 55 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
299 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
2 mg 0.002 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
300 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
20 g 0.016 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.01mg).Procedure as per OIMLR 111-1 guidelines.
301 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
20 mg 0.002 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
302 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
200 g 0.099 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.01mg).Procedure as per OIMLR 111-1 guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 56 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
303 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
200 mg 0.003 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111- 1, 2004.
304 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
5 g 0.006 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
305 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
5 mg 0.002 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
306 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
50 g 0.014 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.01mg).Procedure as per OIMLR 111-1 guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 57 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
307 MECHANICAL-WEIGHTS
MASS - Weights (E2Class & Coarser)
500 mg 0.003 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
308 MECHANICAL-WEIGHTS
MASS - Weights (F1Class & Coarser)
1 kg 0.001 g Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 1mg).Procedure as per OIMLR 111-1 guidelines.
309 MECHANICAL-WEIGHTS
MASS - Weights (F1Class & Coarser)
500 g 0.001 g Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 1mg).Procedure as per OIMLR 111-1 guidelines.
310 MECHANICAL-WEIGHTS
MASS - Weights (F2Class & Coarser)
2 kg 0.009 g Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 10mg).Procedure as per OIMLR 111-1 guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 58 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
311 MECHANICAL-WEIGHTS
MASS - Weights (F2Class & Coarser)
20 kg 0.090 g Using StandardWeights of accuracyClass E2 andElectronic weighingBalance(d: 100mg).Procedure as per OIMLR 111-1 guidelines.
312 MECHANICAL-WEIGHTS
MASS - Weights (M1Class & Coarser)
10 kg 0.083 g Using StandardWeights of accuracyClass E2 andElectronic weighingBalance(d: 100mg).Procedure as per OIMLR 111-1 guidelines.
313 MECHANICAL-WEIGHTS
MASS -WEIGHTS(AccuracyClass F2 and coarser)
5 kg 10.0mg Using E2 ClassStandard Weights andElectronic weighingbalance(d: 10mg).Procedure as per OIMLR111-1.
314 MECHANICAL-WEIGHTS
MASS - Weights(E2Class & Coarser)
100 g 0.089 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.01mg).Procedure as per OIMLR 111-1 guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 59 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
315 MECHANICAL-WEIGHTS
MASS Weights (E2Class & Coarser)
50 mg 0.002 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
316 MECHANICAL-WEIGHTS
Weights (E2 Class &Coarser)
100 mg 0.003 mg Using StandardWeights of accuracyClass E1 andElectronic weighingBalance(d: 0.001mg).Procedure as per OIMLR 111-1 guidelines.
317 OPTICAL- OPTICAL Lux / Light Meter 100 lx to 10000 lx 3.5% Using Light Chamberand Lux Meter ByComparison Method
318 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity (Digital &Analog Thermohygrometer)Temperature &Humidity Meter,Humidity Indicator,Humidity &TemperatureTransmitter withIndicator
20 %RH to 95 %RH@25 ºC
1.48%RH Using StandardHumidity Meter withHumidity Generator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 60 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
319 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity (Digital &Analog Thermohygrometer)Temperature &Humidity Meter,Humidity Indicator,Humidity &TemperatureTransmitter withIndicator
5 °C to 50 °C@60%RH 0.36°C Using StandardHumidity Meter withHumidity Generator
320 THERMAL-TEMPERATURE
Glass Thermometer -80 °C to 150 °C 0.72°C Using SPRT withIndicator & oil
321 THERMAL-TEMPERATURE
Indicators of Oil Baths /Low & High Temp Bath/ Dry bath / furnace /oven/ incubators /autoclave for industrialapplications - singleposition
140 °C to 600 °C 0.35°C Using SPRT & S- TypeThermocouple withdigital Indicator
322 THERMAL-TEMPERATURE
Indicators of Oil Baths /Low & High Temp Bath/ Dry bath /furnace/oven/ incubators /autoclave for industrialapplications - singleposition
-95 °C to 140 °C 0.17°C Using SPRT & S-TypeThermocouple withdigital indicator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 61 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
323 THERMAL-TEMPERATURE
Indicators of Oil Baths /Low & High Temp Bath/ Dry bath/ furnace /oven / autoclave /incubators for industrialapplications - singleposition
600 °C to 1200 °C 2.47°C Using SPRT & S-TypeThermocouple withdigital Indicator
324 THERMAL-TEMPERATURE
Non-ContactThermometerPyrometer
50 °C to 650 °C 6.19°C Using Standard Non-Contact IR Pyrometer,Black Body (Emissivity0.950)
325 THERMAL-TEMPERATURE
Non-ContactThermometerPyrometer
650 °C to 1200 °C 7.88°C Using Standardr Non-Contact IR Pyrometer,Black Body (Emissivity0.950)
326 THERMAL-TEMPERATURE
Temperature (Digital &Analog Thermohygrometer)Temperature &Humidity Meter,Humidity Indicator,Humidity &TemperatureTransmitter withIndicator
5 °C to 50 °C 0.18 °C Using SPRT withIndicator & temperatureGenerator
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 62 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
327 THERMAL-TEMPERATURE
Thermocouples & RTDSensors/ TemperatureSensors with indicators/ Temperature gauges /Transmitters /Temperature Switches& Transmitters withIndicatators
140 °C to 600 °C 0.64°C Using SPRT withIndicator & Dry BlockBath
328 THERMAL-TEMPERATURE
Thermocouples & RTDSensors/ TemperatureSensors with indicators/ Temperature gauges /Transmitters /Temperature Switches& Transmitters withIndicatators
600 °C to 1200 °C 2.53°C Using Fluke S TypeThermocouple withIndicator & Dry BlockBath
329 THERMAL-TEMPERATURE
Thermocouples & RTDSensors/ TemperatureSensors with indicators/ Temperature gauges /Transmitters /Temperature Switches& Transmitters withIndicatators
-95 °C to 140 °C 0.18°C Using SPRT withIndicator & Dry blockBath
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 63 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
Site Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance (1 kHz) 1 nF to 100 nF 0.056% to 0.061% Direct Method usingLCR Meter
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance (1 kHz) 100 nF to 1 µF 0.05% Direct Method usingLCR Meter
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Capacitance (1kHz) 1 µF to 100 µF 0.05% Direct Method usingLCR Meter
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (300 Hz to 10kHz)
1 A to 20 A 0.079% to 0.102% Direct Method withusing master 8½ DMMFluke 8508 A
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (300 Hz to 10kHz)
100 µA to 100 mA 0.03% Direct Method usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 64 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (300 Hz to 10kHz)
100 mA to 1 A 0.041% to 0.079% Direct Method usingmaster 8½ DMM Fluke8508 A
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Current (50 Hz) 20 A to 1000 A 0.5% to 1.0% Direct method masterUsing Shunt With DMM
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Inductance (1kHz) 100 µH to 100 mH 0.236% to 0.065% Direct Method usingmaster LCR meter
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Inductance (1kHz) 100 mH to 10 H 0.065% to 0.073% Direct Method usingLCR Meter
10 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (20 Hz to 50kHz)
1 mV to 100 mV 0.820% to 0.014% Direct method usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 65 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
11 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (20 Hz to 50kHz)
1 V to 100 V 0.017% to 0.011% Direct Method usingmaster 8½ DMM Fluke8508A
12 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (20 Hz to 50kHz)
100 mV to 1 V 0.014% to 0.017% Direct method usingmaster 8½ DMM Fluke8508A
13 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (45 Hz to 1kHz)
100 V to 1000 V 0.01% to 0.007% Direct Method usingmaster 8½ DMM Fluke8508 A
14 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (50 Hz) 1 kV to 25 kV 6.33% to 7.72% Direct Method by usingmaster H.V probeFluke 80K-40 withDMM Fluke 17B
15 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
Voltage (50 kHz to 500kHz)
1 V to 20 V 0.07% to 0.230% Direct Method usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 66 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
16 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Capacitance (1 kHz) 220 pF to 300 nF 5.79% to 0.27% Direct Method usingmaster StandardCalibrator Fluke 5522A& Decade CapacitanceBox
17 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Capacitance (100 Hz) 1 µF to 30 µF 1.55% to 0.56% Direct Method usingmaster StandardCalibrator Fluke 5522A& Decade CapacitanceBox
18 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Capacitance(1 kHz) 300 nF to 100 µF 0.27% to 1.13% Direct Method usingmaster StandardCalibrator Fluke 5522A& Decade CapacitanceBox
19 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1 kHz) 3.3 mA to 1 A 0.15% to 0.073% Direct Method by usingmaster StandardCalibrator Fluke 5522A
20 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1 kHz) 30 µA to 330 µA 0.54% to 0.17% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 67 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
21 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1 kHz) 330 µA to 3.3 mA 0.17% to 0.15% Direct Method by usingmaster StandardCalibrator Fluke 5522A
22 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (10Hz to 1kHz) 330 µA to 3.3 mA 0.25% to 0.26% Direct Method by usingmaster StandardCalibrator Fluke 5522A
23 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (10Hz to 1kHz) 3.3 mA to 3 A 0.26% to 0.23% Direct Method by usingmaster StandardCalibrator Fluke 5522A
24 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (1kHz) 1 A to 10 A 0.073% to 0.12% Direct Method by usingmaster StandardCalibrator Fluke 5522A
25 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (45 Hz to 5kHz)
3 A to 20 A 0.23% to 0.13% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 68 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
26 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Current (50 Hz) 20 A to 1000 A 0.68% to 0.37% Direct Method by usingmaster StandardCalibrator Fluke 5522A& current coil
27 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Inductance (1 kHz) 100 µH to 10 H 2.35 % to 1.14 % Direct Method usingmaster DecadeInductance Box
28 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50 Hz @ UPF 1.2 W to4.8 kW,0.01 A to 20A,120 V to 240 V
0.16% Direct Method usingmaster StandardCalibrator Fluke 5522A
29 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50Hz @ 0.5 Lag, 6 W
to 2.4 kW,0.01 A to20 A,120 V to240 V
0.46% Direct Method usingmaster StandardCalibrator Fluke 5522A
30 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50Hz @ 0.8 Lead 9.6W to 3.8 kW,0.01 A to20 A,120 V to 240 V
0.20% Direct Method usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 69 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
31 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power 50Hz @0.2 Lag, 2.4 W
to 960 W,0.01 A to20 A,120 V to240 V
0.56% Direct Method usingmaster StandardCalibrator Fluke 5522A
32 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power Factor 0.2 Lag to UPF 0.003 Direct Method usingmaster StandardCalibrator Fluke 5522A
33 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Power Factor 0.2 Lead to UPF 0.0003 Direct Method usingmaster StandardCalibrator Fluke 5522A
34 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (10 Hz to 10kHz)
1 V to 30 V 0.080% to 0.042% Direct Method by usingmaster StandardCalibrator Fluke 5522A
35 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (10 Hz to 10kHz)
100 mV to 1 V 0.086% to 0.080% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 70 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
36 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (10 Hz to 10kHz)
30 mV to 100 mV 0.12% to 0.086% Direct Method by usingmaster StandardCalibrator Fluke 5522A
37 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (100kHz) 30 mV to 30 V 0.452% to 0.054% Direct Method by usingmaster StandardCalibrator Fluke 5522A
38 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (100kHz) 30 V to 100 V 0.054% to 0.024% Direct Method by usingmaster StandardCalibrator Fluke 5522A
39 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45 Hz to 1kHz)
30 V to 300 V 0.20% to 0.022% Direct Method by usingmaster StandardCalibrator Fluke 5522A
40 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45 Hz to 1kHz)
300 V to 1000 V 0.022% to 0.035% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 71 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
41 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (450kHz) 30 mV to 3 V 1.116% to 0.121% Direct Method by usingmaster StandardCalibrator Fluke 5522A
42 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45Hz to10kHz)
1 mV to 3 mV 0.712% to 0.24% Direct Method by usingmaster StandardCalibrator Fluke 5522A
43 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
Voltage (45Hz to10kHz)
3 mV to 30 mV 0.24% to 0.042% Direct Method by usingmaster StandardCalibrator Fluke 5522A
44 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 1 A to 20 A 0.080% to 0.052% Direct method by usingmaster 8½ DMM Fluke8508 A
45 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 1 mA to 100 mA 0.002% to 0.008% Direct method by usingmaster 8½ DMM Fluke8508 A
46 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 10 µA to 100 µA 0.0010% Direct method by usingmaster 8½ DMM Fluke8508 A
47 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 100 µA to 1 mA 0.001% to 0.002% Direct method by usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 72 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
48 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 100 mA to 1 A 0.062% to 0.080% Direct method by usingmaster 8½ DMM Fluke8508 A
49 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Current 20 A to 1000 A 1.19% Direct Method using8½ DMM Fluke 8508with Shunt
50 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 Gohm to 10 Gohm 0.116% to 0.133% Direct Method by Usingmaster 8½ DMM Fluke8508 A
51 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 Mohm to 10 Mohm 0.001% to 0.002% Direct Method by Usingmaster 8½ DMM Fluke8508 A
52 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 mohm to 100 mohm 0.061% to 0.207% Direct Method by Usingmaster LCR Meter &DRB
53 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 1 ohm to 100 ohm 0.0015% to 0.0010% Using LCR Meter &DRB
54 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 10 kohm to 100 kohm 0.0007% to 0.0008% Direct Method by Usingmaster 8½ DMM Fluke8508 A
55 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 10 Mohm to 100 Mohm 0.002% to 0.008% Direct method by usingmaster 8½ DMM Fluke8508 A
56 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 Mohm to 1 Gohm 0.008% to 0.116% Direct Method by Usingmaster 8½ DMM Fluke8508 A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 73 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
57 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 mohm to 150mohm
0.206% Direct Method by Usingmaster LCR Meter &DRB
58 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 ohm to 10 kohm 0.0010% to 0.0007% Direct Method by Usingmaster 8½ DMM Fluke8508 A
59 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 100 kohm to 1 Mohm 0.0008% to 0.001% Direct Method by Usingmaster 8½ DMM Fluke8508 A
60 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Resistance 150 mohm to 1 ohm 0.206% to 0.0015% Direct Method by usingmaste LCR Meter &DRB
61 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 1 kV to 20 kV 1.70% to 1.67% Direct Method by usingmaster H.V probeFluke 80K-40 withDMM Fluke 17B
62 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 1 mV to 100 mV 0.44% to 0.0003% Direct Method by usingmaster StandardCalibrator Fluke 5522A
63 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 1 V to 100 V 0.0002% to 0.0003% Direct Method by usingmaster DMM Fluke8508A
64 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 100 mV to 1 V 0.0003% to 0.0003% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 74 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
65 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 100 V to 1000 V 0.0004% to 0.0004% Direct Method by usingmaster StandardCalibrator Fluke 5522A
66 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
Voltage 20 kV to 40 kV 1.67% to 1.65% Direct Method by usingmaster H.V probeFluke 80K-40 withDMM Fluke 17B
67 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 1 A to 10 A 0.027% to 0.063% Direct Method by usingmaster StandardCalibrator Fluke 5522A
68 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 1 mA to 100 mA 0.016% to 0.011% Direct Method by usingmaster StandardCalibrator Fluke 5522A
69 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 10 µA to 100 µA 0.25% to 0.023% Direct Method by usingmaster StandardCalibrator Fluke 5522A
70 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 10 A to 20 A 0.063% to 0.11% Direct Method by usingmaster StandardCalibrator Fluke 5522A
71 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 100 µA to 1 mA 0.023% to 0.016% Direct Method by usingmaster StandardCalibrator Fluke 5522A
72 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 100 mA to 1 A 0.011% to 0.027% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 75 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
73 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Current 20 A to 200 A 0.5% Direct Method usingCurrent Source
74 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Power 10 W to 1 kW,1V to1000V, 1mA to 1000A.
0.08% to 0.45% Using Calibrator Fluke5522A with CurrentCoil Direct Method.
75 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Power (1V to1000V, 1mA to 1000A)
1 KW to 19.9 KW 0.45% to 0.65% Using Calibrator Fluke5522A with current coilDirect Method.
76 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Oscilloscope 1 mV to 130 V 0.29% to 0.096% Direct Method
77 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 0.1 Mohm to 1 Gohm 5.89% to 4.91% Direct Method usingmaster of high stabilityDecade Megohm Box
78 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 Gohm to 100 Gohm 4.91% to 8.61% Direct Method usingmaster of high stabilityDecade Megohm Box
79 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 kohm to 10 kohm 0.0036% to 0.0035% Direct Method usingStandard CalibratorFluke 5522A
80 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 mohm 0.609% Direct Method usingfixed resistor box
81 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 Mohm to 10 Mohm 0.0041% to 0.014% Direct Method usingStandard CalibratorFluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 76 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
82 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 1 ohm to 10 ohm 0.10% to 0.015% Direct Method usingStandard CalibratorFluke 5522A
83 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 kohm to 100 kohm 0.0035% to 0.0034% Direct Method usingStandard CalibratorFluke 5522A
84 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 mohm 0.610% Direct Method usingfixed resistor box
85 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 Mohm to 300 Mohm 0.014% to 0.38% Direct Method usingStandard CalibratorFluke 5522A
86 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 10 ohm to 100 ohm 0.015% to 0.004% Direct Method usingStandard CalibratorFluke 5522A
87 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 Gohm to 1 Tohm 5.81% Direct Method usingmaster of high stabilityDecade Megohm Box
88 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 ohm to 1 kohm 0.004% to 0.0036% Direct Method usingStandard CalibratorFluke 5522A
89 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 100 kohm to 1 Mohm 0.0034% to 0.0041% Direct Method usingStandard CalibratorFluke 5522A
90 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 150 mohm 0.609% Direct Method usingfixed resistor box
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 77 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
91 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 150 mohm to 1 ohm 0.611% to 0.10% Direct Method usingStandard CalibratorFluke 5522A:
92 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 300 Mohm to 1 Gohm 0.38% to 1.78% Direct Method usingStandard CalibratorFluke 5522A
93 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Resistance 50 mohm 0.610% Direct Method usingsing fixed resistor box
94 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 1 mV to 10 mV 0.240% to 0.023% Direct Method by usingmaster StandardCalibrator Fluke 5522A
95 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 1 V to 10 V 0.0015% to 0.0016% Direct Method usingmaster StandardCalibrator Fluke 5522A:
96 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 10 mV to 100 mV 0.023% to 0.0039% Direct Method by usingmaster StandardCalibrator Fluke 5522A
97 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 10 V to 1000 V 0.0016% to 0.0023% Direct Method by usingmaster StandardCalibrator Fluke 5522A
98 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
Voltage 100 mV to 1 V 0.0039% to 0.0015% Direct Method by usingmaster StandardCalibrator Fluke 5522A
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 78 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
99 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Amplitude-Sq wave /Oscilloscope (1 kHz)
1 mV to 55 Vp-p 0.6% to 0.3% Direct Method by usingmaster StandardCalibrator Fluke 5522A
100 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Bandwidth -Oscilloscope
50 kHz to 1 GHz 0.23% to 0.87% Direct Method usingmaster StandardCalibrator Fluke 5522A
101 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(B type)
600 °C to 1750 °C
0.53°C to 0.39°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
102 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller (Jtype)
-200 °C to 1200 °C 0.28°C to 0.31°C Direct Method by usingMaster used- StndCalibrator Fluke 5522A& 6½ DMM
103 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(K type)
-200 °C to 1350 °C 0.26°C to 0.48°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
104 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(N type)
-200 °C to 1300 °C 0.48°C to 0.35°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 79 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
105 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(R type)
10 °C to 1750 °C 0.67°C to 0.48°C Direct Method by usingMaster StandardCalibrator fluke 5522A
106 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(RTD type)
-200 °C to 800 °C 0.05 °C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
107 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller(S type)
10 °C to 1450 °C 0.56°C to 0.54°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
108 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
Temperature Indicator /Recorder / Controller (Ttype)
-200 °C to 400 °C 0.60°C to 0.17°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
109 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(B type)
600 °C to 1750 °C 0.47°C to 0.11°C Direct Method by usingMaster StandardCalibrator fluke 5522A
110 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(E type)
-200 °C to 900 °C 0.20°C to 0.45°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 80 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
111 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller (Jtype)
-200 °C to 1200 °C 0.15°C to 0.25°C Direct Method by usingMaster StandardCalibrator fluke 5522A
112 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(K type)
-200 °C to 1350 °C 0.37°C to 0.48°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
113 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(N Type )
-200 °C to 1300 °C 0.45°C to 0.30°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
114 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(R type)
10 °C to 1750 °C 0.62°C to 0.44°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
115 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(RTD type)
-200 °C to 800 °C 0.071°C to 0.083°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
116 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller(S type)
10 °C to 1750 °C 0.61°C to 0.51°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
117 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
Temperature Indicator /Recorder / Controller (Ttype)
-200 °C to 400 °C 0.55°C to 0.16°C Direct Method by usingMaster StandardCalibrator fluke 5522A& 6½ DMM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 81 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
118 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 GHz 0.0011% to 0.0024% Direct Method usingmaster FrequencyCounter Philips- PM6669
119 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Timer 1 sec to 9000 sec 0.06% to 0.05% Comparison Method byusing master DigitalTimer Beltronics - 501
120 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 1 Hz to 1 GHz 0.004% to 0.006% Direct Method usingmaster StandardCalibrator Fluke 5522A
121 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Timer Marker /Oscilloscope
1 ns to 5 s 0.0003 sec Direct Method usingmaster StandardCalibrator Fluke 5522A
122 MECHANICAL-ACCELERATION ANDSPEED
Centrifuge / CentrifugalMotor / Speed (Non-Contact)
10 RPM to 15000 RPM 1.1% to 1.2% By Comparison methodby using Tachometer
123 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Bench Centre(Parallelity andcoaxiality)
Upto 500mm 7.0µm Using Taper Mandrel
124 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height MeasuringSystem, Res: 0.1µm
0 mm to 1000 mm 5.4µm Using Gauge Block Set
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 82 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
125 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Profile Projector / VideoMeasuring System /Micro Scope
0 ° to 360 ° 50 min of arc Using Glass Anglegauge, Glass Scale
126 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Profile Projector / VideoMeasuring System /Micro Scope
Mag.: 10x to 100x 0.6% Using Glass Anglegauge, Glass Scale
127 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Profile Projector / VideoMeasuring System /Micro Scope (L.C.0.001 mm)
0 mm to 200 mm 2.4 µm Using Glass Anglegauge, Glass Scale
128 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate ( Granite/ Cast Iron SurfacePlate)
6000 mm to 2000 mm 2.0 sqrt(L+ W/150)µm,L W in mm
Using Electronic Level
129 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Tape Scale Calibrator 0 mm to 1000 mm 10.2µm Using Slip Gauge Setand Long Slip Gauges
130 MECHANICAL-HARDNESS TESTINGMACHINES
Brinell HardnessTesting Machine
HBW 5/750 & HBW10/3000
7.1% & 3.65% Using StandardHardness BlocksIS:1500 (Part 2):2013
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 83 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
131 MECHANICAL-HARDNESS TESTINGMACHINES
Rockwell Hardness HRA, HRBW, HRC 1.0 HRA, 1.2 HRBW,0.85 HRC
Using StandardHardness Blocks IS1586(Part2):2018
132 MECHANICAL-HARDNESS TESTINGMACHINES
Vickers HardnessTesting Machine
HV1, HV5, HV10,HV30
5.12%HV1, 3.72 HV5,2.5%HV10, 2.0% HV30
Using StandardHardness BlocksIS:1501(Part2)2013
133 MECHANICAL-PRESSUREINDICATING DEVICES
Digital / Dial VaccumGauges / Transmitters /Transducers.
0 bar to (-) 0.75 bar 0.014 bar Digital Pressure Gaugewith uncertainty of0.0008 bar. Procedurebased on ISO 3567 &ISO 27893 standards.
134 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(HYDRAULIC)Digital /Analog PressureGauges, PressureIndicator WithTransducer /Transmitter, PressureSwitch
0 bar to 1000 bar 0.15 bar Digital Pressure gaugewith uncertainty of0.021 bar. Procedurebased on DKD-R 6-1guidelines.
135 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(HYDRAULIC)Digital /Analog PressureGauges, PressureIndicator WithTransducer /Transmitter & PressureSwitches
0 bar to 700 bar 0.29 bar Digital Pressure gaugewith uncertainty of0.182 bar. Procedurebased on DKD-R 6-1guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 84 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
136 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC) Digital /Dial Gauges / PressureIndicator WithTransmitter /Transducer.
0 bar to 20 bar 0.014 bar Digital Pressure gaugewith uncertainty of0,01bar. Procedurebased on DKD-R 6-1guidelines.
137 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC)Pressure gauges,Magnehelic gauges,Differential PressureTransmitters, LowPressure Indicators/Transducers,Barometer
0 mbar to 500 mbar 0.31 mbar Digital Manometer withuncertainty of 0.06mbar. Procedure basedon DKD-R 6-1guidelines.
138 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC)Digital /Dial Gauges / PressureIndicator WithTransmitter /Transducer.
0 bar to 70 bar 0.04 bar Digital Pressure gaugewith uncertainty of0.022 bar. Procedurebased on DKD-R 6-1guidelines.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 85 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
139 MECHANICAL-PRESSUREINDICATING DEVICES
PRESSURE(PNEUMATIC)Pressure gauges, Magnehelicgauges, DifferentialPressure Transmitters,Low PressureIndicators/Transducers,Barometer.
0 mbar to 2000 mbar 2.14 mbar Digital Manometer withuncertainty of 1.03mbar. Procedure basedon DKD-R 6-1guidelines.
140 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I) Readability :0.0001 mg
1 mg to 2.1 g 0.003mg Using StandardWeights of acccuracyClass E1 andprocedure based OIMLR-76: 2006.
141 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class Ii) Readability :1 mg
1 mg to 1 kg 0.002 g Using StandardWeights of accuracyClass E1 & E2, andprocedure as per OIMLR-76: 2006.
142 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :100 mg
0.1 g to 20 kg 0.10 g Using StandardWeights of AccuracyClass E2 & F1.Procedure as per OIMLR-76: 2006.
143 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III)Readability :10 g
10 g to 100 kg 10.0 g Using StandardWeights of accuracyClass M1 andprocedure as per OIMLR76:2006
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 86 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
144 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I) Readability :0.001 mg
1 mg to 5.1 g 0.005 mg Using StandardWeights of accuracyClass E1 andprocedure as per OIMLR-76: 2006.
145 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I) Readability :0.1 mg
1 mg to 200 g 0.06 mg Using StandardWeights of accuracyClass E1 andprocedure as per OIMLR-76: 2006.
146 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE( Class I)Readability :0.01 mg
1 mg to 50 g 0.011 mg Using StandardWeights of accuracyClass E1 andprocedure as per OIMLR-76: 2006.
147 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class II)Rwadability:10 mg
0.1 mg to 5 kg 0.011 g Using StandardWeights of AccuracyClass E1& E2 .Procedure as per OIMLR 76:2006.
148 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :100 mg
0.1 g to 35 kg 0.97 g Using StandardWeights of accuracyClass F1& M1.Peocedure as perOIML R-76: 2006.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 87 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
149 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :100 mg
0.1 mg to 10 kg 0.037 g Using StandardWeights of AccuracyClass E1& E2.Procedure as per OIMLR-76: 2006.
150 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class III) Readability :50 g
2 kg to 500 kg 20.0 g Using StandardWeights of accuracyClass F2. Peocedureas per OIML R76:2006
151 MECHANICAL-WEIGHING SCALEAND BALANCE
Electronic WeighingBalance (ClassIII)Readability: 100 mg
0.1 mg to 2 kg 0.011 mg Using Weights ofAccuracy Class E1&E2 . Procedure as perOIML R 76:2006.
152 MECHANICAL-WEIGHING SCALEAND BALANCE
ELECTRONICWEIGHING BALANCE(Class IV)Readability :100 g
2 kg to 1000 kg 50.0 g Using StandardWeights of accuracyClass M1, procedureas per OIML R76:2006
153 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity Chambers /Climatic Chamber /EnvironmentalChamber/HumidityGenerator/HumiditySource(Single or MultiPoint)
20 %RH to 95 %RH@25°C& 10°C to 50°C@ 50%RH
2.6%RH, 0.7°C Using Data Loggers byMulti channel Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 88 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
154 THERMAL-TEMPERATURE
Thermal FreezersChambers / Ovens /Incubators (IndustrialPurpose) &Furnace,Cold room,Freezer, Deep Freezer,TemperatureChamber,Hot Air Oven,Furnace, Liquid Bath,Muffle Furnace (MultiPoint)
-80 °C to 200 °C 1.6°C Using RTD / TC anddata Logger (Mapping)
155 THERMAL-TEMPERATURE
Thermal Freezers/Chambers / Ovens /Incubators (IndustrialPurpose) & Furnance -multipoint
200 °C to 1200 °C 2.5°C Using RTDThermometer & N TypeThermocouples withMultichannelTemperature Recorder
156 THERMAL-TEMPERATURE
Thermocouples & RTDSensors/ TemperatureSensors with indicators/ Temperature gauges /Transmitters /Temperature Switches& Transmitters withIndicatators
140 °C to 600 °C 0.64°C Using SPRT withIndicator & Dry BlockBath
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 89 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
157 THERMAL-TEMPERATURE
Thermocouples & RTDSensors/ TemperatureSensors with indicators/ Temperature gauges /Transmitters /Temperature Switches& Transmitters withIndicatators
600 °C to 1200 °C 2.53°C Using Fluke S TypeThermocouple withIndicator & Dry BlockBath
158 THERMAL-TEMPERATURE
Thermocouples & RTDSensors/ TemperatureSensors with indicators/ Temperature gauges /Transmitters /Temperature Switches& Transmitters withIndicatators
-95 °C to 140 °C 0.18°C Using SPRT withIndicator & Dry blockBath
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name VAIDYANATHESHWARA INSTRUMENTS, NO. 301/A, 9TH MAIN ROAD, 3RDCROSS, RAJIV GANDHI NAGAR, BENGALURU, KARNATAKA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2473 Page No. : 90 / 90
Validity 27/10/2019 to 26/10/2021 Last Amended on 22/11/2019